FV + STU + GT3U at Buttonwillow Raceway Park

2023-03-01 STU E&O STU NA Weight Chart.

#33737 from Eric Heinrich · Rule change · TB 23-03 (2023-03 Fastrack)

In STU, GCR Section 9.1.4.1.H.1. chart, Factory Engine Displacement (cc) Minimum Weight (lbs), change as follows:
"2450 2596 2595"
"2600 2860 2710"

2023-04-01 STU Alternate OEM Miata Intake Manifold

#33827 from Brandon Steinhauer · Rule change · TB 23-04 (2023-04 Fastrack)

In STU Spec lines, classify Mazda BP5A as follows:
STU Maximum Displacement (cc's) Minimum Weight Notes
Mazda BP5A 1839 Chart May use engine in its entirety or specific
components from the engine.

2023-07-01 STU 2022 Toyota GR Cup for STU

#34449 from Club Racing Board · Rule change · TB 23-06 (2023-05 Fastrack)

In STU Spec Lines, Toyota GR Cup (2022-), classify as follows:

A specification table follows in the original; it is not shown here.

2023-12-01 FV FV Wheel Bearing Clarification

#35150 from Formula/Sports Racing Committee · Rule change · TB 23-12 (2023-12 Fastrack)

In FV, GCR section 9.1.1.C.10.G, change as follows:
"Front W wheel bearings"

2024-02-01 STU ST Electric-Assisted Steering Systems

#35066 from Jose Osiris Pena · Rule change · TB 24-02 (2024-01 Fastrack)

In GCR, Section 9.1.4.M.16., change as follows:
"Power steering may be modified in any of the following ways:
a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be
modified internally to work without pump.
b. an OEM manual steering rack for that model may be fitted
c. an electric power steering pump may be fitted
d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used
e. an OEM hydraulic-assisted steering system may be used"

2024-03-01 STU Letter #35397 addendum

#35453 from Aaron Fitzsimmons · Rule change · TB 24-03 (2024-03 Fastrack)

In STU Spec Lines, Mini Cooper S SC with Minimum Weight 1900 and 2100, add to Notes:
"Alternate LEAP OMICRON hood scoop part # LEP-OMICRON3 is permitted."

2024-03-01 STU S54 Drysump

#35464 from Macey Urso · Rule change · TB 24-03 (2024-03 Fastrack)

In STU Spec Lines, BMW S54 B32 OEM, add to Notes as follows:
"Dry Sump oiling system permitted."

2024-08-01 STU RWD Turbo Disadvantage

#36255 from David Fiorelli · Rule change · TB 24-08 (2024-08 Fastrack)

In GCR, Section 9.1.4.1.H.3 - Inlet Restrictor (mm) Minimum Weight (lbs) table, change as follows:
"RWD cars must reduce restrictor 1 mm from this table"

2024-10-01 FV Disc Brakes

#36822 from Guy Bellingham · Rule change · TB 24-10 (2024-10 Fastrack)

In FV, GCR section 9.1.1.C.4.D, change as follows:
"Any ferrous alloy, unvented rotor may be used, but must have a maximum diameter of 11.75 in. and a minimum thickness of
0.20 in. The otherwise smooth rotor may not be cross-drilled and may have a maximum of three pad cleaning grooves per side."

2024-11-01 STU R53 15% Pulley Request

#36980 from Aaron Fitzsimmons · Rule change · TB 24-11 (2024-11 Fastrack)

In STU Spec Lines, Mini Cooper S SC, add to notes:
1900: "Stock supercharger pulley. 2.565 diameter."
2100: "JCW Pulley permitted. May run a 2.285 diameter pulley."

2024-12-01 STU Request to Remove Miata Hubs from General category

#37138 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)

In GCR, Section 9.1.4.M.18., change as follows:
"18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda
Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."

2024-12-01 STU BMW N54/N55 Engine Allowance

#37146 from Martin Sarukhanyan · Rule change · TB 24-12 (2024-12 Fastrack)

"Turbo inlet restrictors designed per GCR Appendix F Technical Glossary definition of “Turbo Inlet Restrictor” may be required;
see table 9.1.4.1.H.h.2 3. Swapping of turbochargers between engine makes and models is prohibited. Supercharged cars may be
approved on a case-by-case basis; twin turbo engines are allowed on a case-by-case basis only. Contact the Road Racing
Technical Office for details. Twin turbo engines may be converted to single turbo using one of the allowed alternate turbos (see
9.1.4.1.H.3 2). Aftermarket turbocharger and supercharger kits will be allowed on a case-by-case basis.

2025-01-01 STU Audi 1.8t Wagon STU Table B

#36685 from Mike McLaughlin · Rule change · TB 25-01 (2025-01 Fastrack)

In STU Spec Lines, Table B: Alternate Vehicle and Engine Requirements, delete Audi/VW 1.8 Turbo in its entirety.
In STU Spec Lines, Table B: Alternate Vehicle and Engine Requirements, Porsche 944 w/Max Displacement 1800, change as
follows:
Weight: "3050 Chart"
Notes: "VW/Audi 1.8L 35mm turbo engine permittedinlet restrictor required."

2025-01-01 STU Merger GT3 to STU

#37486 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)

In STU, Table C, change STU-GT3 charge as follows:
"(Effective January 1, 2026) TABLE C: STU-GT3U"

2025-01-01 STU GT3 TCR Tire allowance

#37494 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)

In STU, Table C, GT3 TCR, add to Notes the following:
"May run DOT approved tire with maximum section width of 275 with 100 pound weight adder. May not run A compound with
275."

2025-03-01 STU BMW N54/N55 Engine Allowance Follow Up

#37447 from Martin Sarukhanyan · Rule change · TB 25-03 (2025-03 Fastrack)

In STU Spec Lines, Table A, classify BMW N54/N55 as follows:
STU Maximum Displacement
(cc's) Minimum Weight Notes
BMW N54/N55 3.0 Chart +3% (DI) Short blocks, heads, and intakes may be
freely swapped within these engine
designations. N54 twin turbo not allowed

2025-03-01 STU STU Mini Cooper pulley size clarification re: letter #36980

#37717 from Aaron Fitzsimmons · Rule change · TB 25-03 (2025-03 Fastrack)

In STU Spec Lines, Mini Cooper S SC, add to notes:
2100: "May run a 2.285 2.185 diameter pulley."

2025-03-01 STU Question About a Weight Modifier

#37782 from Peter St Pierre · Rule change · TB 25-03 (2025-03 Fastrack)

In STU Spec Lines, Table A, Honda K20C1 Turbo I4, add to Notes the following:
"The 3% DI weight adder does not need to be applied."

2025-03-01 STU Increase Minimum Weight

#37919 from Club Racing Board · Rule change · TB 25-03 (2025-03 Fastrack)

In STU Spec Lines, Table C: STU-GT3U, change Minimum Weight as follows:
"150 250 pounds"

2025-03-01 GT3U Increase Minimum Weight

#37919 from Club Racing Board · Rule change · TB 25-03 (2025-03 Fastrack)

In STU Spec Lines, Table C: STU-GT3U, change Minimum Weight as follows:
"150 250 pounds"

2025-04-01 GT3U TCR Rulesets

#37981 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)

In STU-GT3U Spec Lines, Table C, add the following:
"Table C: STU-GT3U
Refer to section 9.1.2."
In GCR, Section 9.1.4.H.7, change as follows:
"All current STU cars, except TCR cars, may reduce their weight by 4% after all other modifiers"

2025-05-01 STU Wheel Size Inconsistency

#38018 from David Fiorelli · Rule change · TB 25-05 (2025-05 Fastrack)

In GCR, Section 9.1.4.1.F.1., change as follows:
"Wheels may not exceed 18 inches in diameter. or 8.0 inches in width for vehicles 2950 lbs. and under minimum allowed race
weight. Vehicles over 2850 minimum allowed race weight may use a 9 inch wide wheel. Cars equal to or less than 2,850 lbs.
minimum allowed race weight may not use wheels wider than 8 inches. Cars greater than 2,850 lbs. minimum allowed race
weight may not use wheels wider than 9 inches."

2025-05-01 STU Table C: STU-GT3U Clarification

#38268 from Club Racing Board · Rule change · TB 25-05 (2025-05 Fastrack)

In STU Spec Line, Table C: STU-GT3U, change as follows:
Minimum Weight: “Current GT3 race weight plus 250 225 pounds”
Notes: "DOT approved tire with maximum section width of 245. GT3 cars base wheel is a maximum of 15”x9”. 18”x9” wheels
allowd with a 3% weight addition. GT3 cars utilizing 15”x7” wheels are limited to a maximum section width of 225 with a 25
pound weight reduction"
"All GT3U (Majors and Runoffs) cars using up to 15"x7" wheels limited to 225 section width tires shall run at current GT3 race
weight plus 225lbs. All Gt3U cars shall run a DOT approved tire with a maximum section width of 245. GT3U cars are allowed
optional 15"x9" wheels with a 1.5% weight addition or up to 18"x9" wheels with a 3.0% weight addition to the total weight

2025-05-01 GT3U Table C: STU-GT3U Clarification

#38268 from Club Racing Board · Rule change · TB 25-05 (2025-05 Fastrack)

In STU Spec Line, Table C: STU-GT3U, change as follows:
Minimum Weight: “Current GT3 race weight plus 250 225 pounds”
Notes: "DOT approved tire with maximum section width of 245. GT3 cars base wheel is a maximum of 15”x9”. 18”x9” wheels
allowd with a 3% weight addition. GT3 cars utilizing 15”x7” wheels are limited to a maximum section width of 225 with a 25
pound weight reduction"
"All GT3U (Majors and Runoffs) cars using up to 15"x7" wheels limited to 225 section width tires shall run at current GT3 race
weight plus 225lbs. All Gt3U cars shall run a DOT approved tire with a maximum section width of 245. GT3U cars are allowed
optional 15"x9" wheels with a 1.5% weight addition or up to 18"x9" wheels with a 3.0% weight addition to the total weight

2025-07-01 STU 2.8-3.2L N/A Engine Allowances

#38007 from Ben Slechta · Rule change · TB 25-07 (2025-07 Fastrack)

In GCR, Section 9.1.4.G.1, add the following:
"A maximum section width of 245 is permitted. Cars over 3150 lbs. may run a 275 tire with a 2% weight adder."

2025-07-01 STU 2006-2015 Mazda Miata Intake Manifold

#38422 from German Candelario Candelario · Rule change · TB 25-07 (2025-07 Fastrack)

In STU, Table A, Mazda MZR (LF, L3, L5), change Notes as follows:
"May use Goodwin Part # 61-2510 or Gato Performance Part #31972 Intake manifold . "

2025-07-01 STU Requesting Approval of the JDM Honda h23a

#38489 from Eric Fiest · Rule change · TB 25-07 (2025-07 Fastrack)

In STU, Table B, classify Honda JDM H23a as follows:
STU Maximum Displacement (cc's) Minimum Weight Notes
Honda JDM H23a 2259 Chart Must meet all ST engine regulations.

2025-08-01 STU STU-TCR Adjustments

#38723 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)

In STU Spec Lines, Table C: STU-GT3U, GT3-TCR, change as follows: Remove the current TCR spec line and add the TCR spec lines
from GT3 that are being removed, adding the below to the notes.
"DOT approved tire with maximum section width of 245. May run DOT approved tire with maximum section width of 275 with
100 150 pound weight adder. May not run A-compound with 275. STU-TCR spitters and side valance must comply with
9.1.4.D.3.f. STU-TCR chassis ride height must comply with 9.1.4.1.A.1."

2025-08-01 STU Lotus Weight Reduction

#38772 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)

In 9.1.2. GT2/ST Spec Lines, Lotus Evora GT4, change Weight as follows:
"2750 2700"
In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows:
Lotus Elise Cup R: "2300 2250"
Lotus Elise SC/ Lotus Exige SC: "2300 2550
2500 2450"

2025-09-01 STU Lotus Weight Reduction E&O

#38919 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)

In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows:
Lotus Elise SC/ Lotus Exige SC: "2450 2250"

2025-11-01 STU Non-Homologated Engine Swaps - Specifically K24A2 w/ Honda CRZ

#38746 from William Rori · Rule change · TB 25-09 (2025-09 Fastrack)

In STU Spec Lines, Table B: Alternate Vehicle and Engine Allowances, Honda K24, change Weight as follows:
"(Effective 11/1/2025) Chart + 2%"

2025-12-01 STU Turbo Inlet Restrictor Table

#38961 from John Weisberg · Rule change · TB 25-12 (2025-12 Fastrack)

In GCR, Section 9.1.4.H.3, change chart as follows:

A specification table follows in the original; it is not shown here.

2025-12-01 STU 275 Tire Rule

#38983 from Peter Federlin · Rule change · TB 25-12 (2025-12 Fastrack)

In GCR, Section 9.1.4.G.1., change as follows:
"A maximum section width of 245 is permitted. Cars over 3150 lbs. may run a 275 tire with a 2% weight adder."

2025-12-01 STU STU Honda Engine weight penalty

#39375 from Super Touring Committee · Rule change · TB 25-12 (2025-12 Fastrack)

In STU Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Minimum Weight as follows:
Honda K20: "Chart + 2%"
Honda K24: "Chart + 2%"

2026-01-01 STU Request for Permission on Aftermarket Turbo Kit and Intake

#39529 from John Grim · Rule change · TB 26-01 (2026-01 Fastrack)

In STU Spec Lines, Table A: Alternate Vehicle and Engine Allowances, Mazda MZR (LF, L3, L5), change Notes as follows:
"Short blocks, heads, and intakes may be freely swapped within these engine designations. May use Goodwin Part # 61-
2510 or, Gato Performance Part #31972 or Jack Spania Racing 70 mm sheet-metal aluminum Intake manifold. Must use stock
throttle body or Acura part number 16400-PND-A17."
In STU Spec Lines, Table A: Alternate Vehicle and Engine Allowances, classify Mazda MZR (LF, L3, L5) Turbo as follows:
STU Maximum Displacement (cc's) Minimum Weight Notes
Mazda MZR (LF, L3,
L5) Turbo