One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Elan DP02/Mazda
P
1
1:32.576Jim Devenport
1:32.872Jim Devenport
1:33.972Jim Devenport
171.9Jim Devenport
25.461Jim Devenport
26.606Jim Devenport
40.217Jim Devenport
Dauntless Stohr
P
2
1:36.516Johnnie Crean
1:36.516Johnnie Crean
1:37.287John Manfroy
160.4John Manfroy
25.956Johnnie Crean
27.257John Manfroy
42.386John Manfroy
Dauntless Stohr
P
1
1:36.516Johnnie Crean
1:36.516Johnnie Crean
1:39.209Johnnie Crean
157.4Johnnie Crean
25.956Johnnie Crean
28.143Johnnie Crean
42.417Johnnie Crean
Dauntless-Stohr P07d
P
1
1:37.287John Manfroy
1:41.818John Manfroy
1:37.287John Manfroy
160.4John Manfroy
26.696John Manfroy
27.257John Manfroy
42.386John Manfroy
Stohr WF1
P
1
1:38.716Kevin Mitz
1:38.716Kevin Mitz
1:39.638Kevin Mitz
155.4Kevin Mitz
26.934Kevin Mitz
28.397Kevin Mitz
43.336Kevin Mitz
Penton Norma M20FC
P
1
1:39.296Joseph Moran
1:39.296Joseph Moran
1:40.832Joseph Moran
149.0Joseph Moran
27.106Joseph Moran
28.111Joseph Moran
43.651Joseph Moran
MG Midget
HP
4
1:40.295Bill Okell
2:04.965Brian Linn
2:03.082Lee Fleming
126.2Lee Fleming
27.543Bill Okell
28.857Bill Okell
43.861Bill Okell
Toyota Yaris
HP
1
2:08.224Bobby Beyer
2:10.927Bobby Beyer
2:08.224Bobby Beyer
92.3Bobby Beyer
34.660Bobby Beyer
37.206Bobby Beyer
56.144Bobby Beyer
Mini Cooper
HP
1
2:09.238Tom Tuttle
2:11.042Tom Tuttle
2:09.238Tom Tuttle
99.0Tom Tuttle
34.631Tom Tuttle
37.306Tom Tuttle
56.479Tom Tuttle
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21
HP Request Competition Adjustment to BMW Z3 2.5L
#37120 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)
slowerEP BMW Z3 and 3-series models get smaller intake restrictors: Z3 2.5L to 52mm, Z3 2.8L to 55mm, 328i to 58mm, 325i to 56mm.
In EP Spec Lines, change Notes as follows: BMW Z3 2.5LL "(Effective 3/1/2025) 56mm 52mm Flat Plate Intake Restrictor is required." BMW Z3 2.8L (97-00): "(Effective 3/1/2025) 59mm 55mm Flat Plate Intake Restrictor is required." BMW 328i/is E36 (96-99): "(Effective 3/1/2025) 62mm 58mm Flat Plate Intake Restrictor is required." BMW 328i/ci E46 (01-06): "(Effective 3/1/2025) 62mm 58mm Flat Plate Intake Restrictor is required." BMW 325i/is E46 (01-06): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required." BMW 325i/is E-36 (92-95): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required." BMW 325is M-Technic (1994): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required."
HP Interpretation of Production Rules on Mirrors
#37235 from Lawrence Slivinski · Rule change · TB 25-03 (2025-03 Fastrack)
neutralEP, FP, HP: interior or exterior mirrors meeting rule 9.3.36 now permitted.
In GCR, add new rule as Section 9.1.5.E.10.f: "Any interior or exterior mirror(s) that meets rule 9.3.36 may be used."
HP HP Class Adjustments
#37459 from Production Committee · Rule change · TB 25-01 (2025-01 Fastrack)
slowerHP Mazda 2 11-14 base weight up 50 lbs to 2045; all VW 80s models up 50 lbs to 2150 base.
#37466 from Michael Unger · Rule change · TB 25-03 (2025-03 Fastrack)
fasterEP Honda S2000 1997cc base loses 75 lbs to 2375; 2157cc base loses 60 lbs to 2450.
In EP, Spec Lines make the following weight changes:
A specification table follows in the original; it is not shown here.
HP Mazda 1999 Miata 1.8L
#37488 from Joe Carr · Rule change · TB 25-03 (2025-03 Fastrack)
fasterEP Mazda MX-5/Miata 99-05 minimum weight drops to 2100 lbs, 2153 lbs with power adder, 2205 lbs with two adders.
In EP Spec Lines, make the following weight change: Mazda MX-5 /Miata (99-05): "2150 2100 *2204 2153 **2258 2205"
HP MINI Cooper (07-13) Spec Line Correction: Errors and Omissions
#37560 from Robert Bax · Rule change · TB 25-03 (2025-03 Fastrack)
slowerHP Mini Cooper 07-13 engine corrected to DOHC; valve lift limit reduced to 0.390 inches.
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), change as follows: Engine Type: "4 Cyl SOHC DOHC" Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
Applies to Mini Cooper on this page: Tom Tuttle
HP Request for Classification of Chevrolet Spark
#37755 from Kristian Smith · Rule change · TB 25-04 (2025-04 Fastrack)
neutralChevrolet Spark 16-22 classified HP Pre at 1850 lbs minimum weight, fuel injected, 1399 cc.
In HP Spec Lines, classify the Chevrolet Spark (16-22):
A specification table follows in the original; it is not shown here.
HP Request to Lower Ford Festiva Minimum Weight to 1600 LBS
fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.
In HP Spec Lines "Ford Festiva (88-93)" change as follows: Weight: "1700 1600 *1743 1640 **1785 1680" Notes: "Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."
P Add missing punctuation marks
#38150 from Club Racing Board · Rule change · TB 25-05 (2025-05 Fastrack)
neutralClass P adds clarification notes on restrictor requirements, throttle bodies, Mazda 12A engine spec, and P2 auto-based engine rules.
In P Engine Table, Spec Line D notes, add the following: "No restrictor required at 1150 lbs. minimum weight." In P Engine Table, Spec Line G notes, add the following: "Group CN non-composite chassis with Honda K20A-FD2 may use unrestricted individual throttle bodies at 1500 lbs. minimum weight." In P Table 1, Beasley B2 spec line notes, add the following: "Engine must be Mazda 12A rotary with 40.5mm venturi. Car must comply with all other Prototype requirements." In P Table 1, P2 cars built to 2000cc auto-based specification spec line notes, add the following:
Show 3 more lines
"Car must comply with all other P2 rules applicable to cars using stock production-based four-cylinder automotive engines. Note: Competitors are also free to modify their cars to comply with the general Prototype rules and Engine Table Spec Line H instead."
HP Base Weight Adjustment for H-Production X1/9 Spec Lines
#38255 from Matthew Brannon · Rule change · TB 25-06 (2025-06 Fastrack)
fasterHP Fiat X-1/9 base weights reduced 50–53 lbs across 1300 and 1500 spec lines.
In HP Spec Lines, change Weight as follows: Fiat X-1/9 & Bertone1500: “1790 1740 *1835 1784 **1880 1827” Fiat X-1/9 1300: “1650 1600 *1691 1640 **1733 1680” Fiat X-1/9 1300: “2060 2010” Fiat X-1/9 1500: “1950 1900”
slowerEP BMW Z4 03-05 restricted to 52mm flat plate intake restrictor.
In EP Spec Lines, BMW Z4 (03-05), add to Notes the following: “52mm Flat Plate Intake Restrictor.”
HP EP Fiat 124 Spider Competition Adjustment Request
#38498 from John Baucom · Rule change · TB 25-07 (2025-07 Fastrack)
fasterEP Fiat 124 Spider 1600 & 2000 weight drops 50 lbs to 2000; carburetors gain 2mm chokes to 36mm.
In EP Spec Lines, Fiat 124 Sport Spider 1600 & 124 Spider 2000, change as follows: Weight: "2050 2000" Carburetor No. & Type: "(2) Weber 40 IDF-40IFI, (2) Solex C40P116, 34 36mm choke(s) req’d, (2) Weber 45DCOE w/ 34 36 mm choke(s) on I.R. manifold or fuel injection."
P RM 25-05 - Prototype Engine Table A, 2 Cycle Restrictor Change
#38929 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)
slowerPrototype Engine Table A 2-cycle restrictor reduces from 40mm to 38mm venturi size.
Effective 8/1/25 in Prototype Engine Table, Spec Line A, change the restrictor as follows: "40mm 38mm Restricted Venturi Size"
P 13B Rotary Engine Rules Change Request
#38856 from Jason Vinkemulder · Rule change · TB 25-09 (2025-09 Fastrack)
unclearP class 13B rotary engine restrictor changes to 40mm SIR fuel injection or 41.5mm venturi carburetor.
Effective 9/1/25 in Prototype Engine Table, Spec Line K, change the restrictor as follows: "40mm SIR with fuel injection or 41.5mm venturi with carburetor"
P Add Radical Cup series Radical SR3 spec line to Table 1
#38916 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)
neutralPrototype class adds Radical SR3 spec line to Table 1 effective 9/1/25.
Effective 9/1/25 in Prototype Table 1 (Spec Line Cars), add the following:
P Clarify spec line cars language
#38943 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)
neutralPrototype P2 cars may now run P2 spec or modified Prototype spec in Prototype class; clarified language and added Radical Cup series table.
Effective 9/1/25, in Prototype, GCR section 9.1.8.B.K, change as follows: "P2 cars may compete in either the Prototype class or the P2 class but must participate in the Prototype class to the extent necessary to qualify for an invitation to the Runoffs in Prototype. P2 cars may be modified to comply with the general Prototype rules and Prototype Engine Table or may continue to run in P2 specification in the Prototype class as permitted in Table 1 below." Table 1 (Spec Line Cars)
A specification table follows in the original; it is not shown here.
HP HP Plymouth Arrow spec omission
#38995 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralHP Plymouth Arrow transmission max speeds clarified to 4 or 5.
In HP Spec Lines, Plymouth Arrow (76-80), add the following wording to Trans. Speeds(max): "4 or 5"
HP Add Wheel Diameter to Appendix G
#39008 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP wheel diameter added to Appendix G as absolute maximum specification.
In Appendix G.2.3, change as follows: "Rim width and diameter are is absolute maximums."
HP Add TB ID tolerance to general Prod rules
#39009 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.
In GCR, Section 9.1.5.E., change as follows: 9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished." 9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must remain stock (tolerance of +/-.25mm)."
HP Please Lower Weight of 280Z
#38871 from Matthew Miller · Rule change · TB 25-09 (2025-09 Fastrack)
fasterEP Nissan 280Z minimum weight reduced from 2560 to 2400 lbs.
In EP Spec Lines, Nissan 280Z, change Weight (lbs) as follows: "(Effective 11/1/2025) 2560 2400 *2624 2460 **2688 2520"
HP Miata Weight Adjustment Follow Up
#38949 from Don Tucker · Rule change · TB 25-10 (2025-10 Fastrack)
fasterEP Mazda MX-5 1.8L 90-97 weight reduced to 2125 lbs from 2150 lbs.
In EP Spec Lines, Mazda MX-5 / Miata 1.8L (90-97), Effective 11/1/2025 make the following weight change: "2150 2125"
HP Weight Break for 1098 Midget / Sprite
#38970 from Kendall Jones · Rule change · TB 25-10 (2025-10 Fastrack)
In HP Spec Lines, Austin-Healey Sprite/Midget 1098cc, Effective 11/1/2025make the following weight change: "1630 1550"
HP HP Volvo 142 spec omission
#38994 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".
In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."
HP HP Mini DOHC 1.6
#38996 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following changes to the Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
HP Add to Rabbit description
#39019 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.
In FP Spec Lines, make the following spec line correction: "Volkswagen Rabbit (Includes Convertible Cabriolet)" In HP Spec Lines, make the following spec line correction: "Volkswagen Rabbit 1588 (Includes Cabriolet)" "Volkswagen Rabbit 1715 (Includes Cabriolet)" "Volkswagen Rabbit 1780 (Includes Cabriolet)"
HP Clean-up 9.1.5.E.7e
#39025 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.
In GCR, Section 9.1.5.E.7., change as follows: "e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear disc brakes under this rule. When converting from rear drum brakes to rear disc brakes: 1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on the vehicle’s spec line. 2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock
Show 3 more lines
from converting to rear disc brakes under this rule. 3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes as stock from converting to rear disc brakes under this rule."
HP Add TB size to Ford Mustang (94-98) Spec Line
#39130 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP Ford Mustang (94-98) fuel injected throttle body inside diameter specified at 60.
In EP Spec Lines, Ford Mustang (94-98) add the following to the Fuel Injected Equipped Throttle Body Inside Diameter column: "60"
HP Request to Re-Classsify Datsun SPL-311 to HP from FP
#39116 from Robert Heatwole · Rule change · TB 25-12 (2025-12 Fastrack)
neutralDatsun SPL-311 newly classified to HP at 2050 lbs with 1595cc OHV iron engine and specified carburetors.
In HP Spec Lines, classify Nissan/Datsun SPL 311 as follows:
A specification table follows in the original; it is not shown here.
HP TR2 Notes E&O
#39180 from Anthony Parker · Rule change · TB 25-12 (2025-12 Fastrack)
unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.
In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes: "Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."
HP Balance of Power
#39187 from Jim Simaras · Rule change · TB 25-12 (2025-12 Fastrack)
slowerEP BMW Z3 2.5L restrictor reduced 52mm to 50mm, weight increased to 2550 lbs base; five other BMW models get smaller restrictors.
In EP Spec Lines, make the following changes to Restrictors: BMW Z3 2.5L: "52mm 50mm Flat Plate Intake Restrictor" BMW Z3 2.8L (97-00): "55mm 53mm Flat Plate Intake Restrictor" BMW 328i/is E36 (96-99): "58mm 55mm Flat Plate Intake Restrictor" BMW 328i/ci E46 (01-06): "58mm 55mm Flat Plate Intake Restrictor" BMW 325i/is (E46) (01-06): "56mm 53mm Flat Plate Intake Restrictor" BMW 325is M-Technic (1994): "56mm 53mm Flat Plate Intake Restrictor" BMW 325i/is E-36 (92-95): "56mm 53mm Flat Plate Intake Restrictor"
Show 4 more lines
In EP Spec Lines, BMW Z3 2.5L, change Weight as follows: "2500 2550 *2563 2614 **2625 2678"
HP Alternative BOP Request for 84-87 Honda CRX/Civic
#39223 from Bill Lamkin · Rule change · TB 25-12 (2025-12 Fastrack)
fasterHP Honda Civic and CRX models get wider 13-inch wheels: 6 to 7 inches.
In HP Spec Lines, change Wheels as follows: Honda Civic: "13 x 6 7" Honda Civic DX (92-95): "13 x 6 7" Honda Civic/Si (84-87): "13 x 6 7" Honda Civic 1.5 (88-91): "13 x 6 7" Honda CRX/Si (84-87): "13 x 6 7" Honda CRX 1.5(88-91): "13 x 67"
neutralPrototype carbon-carbon and carbon-ceramic brake rotors now permitted instead of prohibited.
In Prototype, GCR section 9.1.8.B.F.2, change as follows: "Brake calipers may be ferrous or aluminum alloy. Effective 1/1/2026, carbon-carbon and carbon-ceramic brake rotors are prohibited and rotors must be ferrous. Brake rotor material is unrestricted."
HP E/O: Improve Consistency of the Spec Lines
#39500 from Robert Bax · Rule change · TB 26-01 (2026-01 Fastrack)
unclearHP Toyota MR-2 1.6L (85-89) compression ratio set to 11.0:1.
In HP Spec Line, Toyota MR-2 1.6L (85-89), change Comp. Ratio as follows: "11.0:1"
HP Request to Reclassify BMW 2002 Into H Production
#39567 from Jonathan Kinberg · Rule change · TB 26-01 (2026-01 Fastrack)
neutralBMW 2002 newly classified to H Production at 2350 lbs with 1990cc iron block, 40 DCNF carburetor, 11.0:1 compression.
In HP Spec Lines, classify BMW 2002, as follows:
A specification table follows in the original; it is not shown here.
HP Triumph Spitfire 1296cc Compression Ratio Increase to 12:1
#39589 from Neil Verity · Rule change · TB 26-02 (2026-02 Fastrack)
fasterHP Triumph Spitfire 1296cc compression ratio increases from 11.0 to 12.0:1.
In HP Spec Lines, make the following spec line changes: Triumph Spitfire: Carburetion "Valves: (I) 33.0/(1.30) (E) 29.7/(1.17) Comp. ratio 11.0 12.0:1, Valve lift .450” Trans. Speeds: 4" Triumph Spitfire Mk. III & IV 1500: Carburetion