BoP Labbeta

BoP Lab / Portland International Raceway

HP at Portland International Raceway

No mapOregon 2025, Oregon Region Hoosier SCCA Super Tour @ Portland International Raceway

Track map: sectors and speed trap

Track map with timing sectors and speed trap
Shown for: Oregon 2026 (qualifying, race)
Class · click a class to switch, + to compare alongside
AS+B-Spec+EP+F6+FA+FE2+FF+FP+FV+GT1+GT2+GT3+GT3U+GTL+GTX+HP×P+P1+P2+SM+SMX+SRF3+STL+STU+T1+T2+T3+T4+
Track configuration
Events

This track has been raced on 2 configurations (19 Scoring Sidebar, 1.88 mi; 19 Scoring Sidebar, 1.97 mi). Laps on different configurations are not comparable, so only events on the 1.88 mile layout are shown; switch above to see the others.

PosCarDriverClass#LapTheoreticalQualRace5-lap stintConsistencyTrapS1S2S3
1MG MidgetBill OkellHP71:33.460 A-R21:32.9511:34.439 A-Q11:33.460 A-R21:34.293 A-R2+0.817 A-R2111.1 A-R234.534 A-R231.629 A-R226.788 A-R2

One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it. Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.

Sectors

Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.

Rule changes between these events

Oregon Region Hoosier SCCA Super Tour @ Portland International Raceway → Oregon 2025 2024-05-11 to 2025-05-10

HP NIssan 300ZX Z31 to EP

#35830 from Murphy Nichols · Rule change · TB 24-06 (2024-06 Fastrack)

neutralNissan 300ZX 84-89 classified to EP at 2550 lbs minimum, 2960cc 6-cyl SOHC, fuel injection, 12.0:1 compression limit, 0.500" valve lift limit.

In EP Spec Lines, classify Nissan 300ZX (84-89), as follows:

A specification table follows in the original; it is not shown here.

HP RX7 1993 and Up Request In EP Spec Lines, classify

#36031 from Edward Zabinski · Rule change · TB 24-06 (2024-06 Fastrack)

neutralMazda RX-7 92-97 newly classified EP Prep Level 2 at 2200–2310 lbs with 13B 6-port rotary engine.

Mazda RX-7 (92-97) as follows:

A specification table follows in the original; it is not shown here.

HP Clean-up Multiple EP RX-8 Spec Lines In EP

#36156 from Production Committee · Rule change · TB 24-06 (2024-06 Fastrack)

neutralEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.

Spec Lines, make the following changes to the two Mazda RX-8 spec lines.
Remove spec line entirely:
Mazda RX-8 (04-11)
Remove the wording "alternate":
Mazda RX-8 (04-11)(alternate)
Spec Mazda (SM/SMX) None.

HP Errant entry in HP production line item

#36231 from Angus Crome · Rule change · TB 24-08 (2024-08 Fastrack)

neutralHP Volkswagen Golf and Jetta 85-92 track correction: front 1537mm (60.5in), rear 1529mm (60.2in).

In HP Spec Lines, change Track (F/R)mm/(in.) as follows:
Volkswagen Golf (GTI, GT, GL) (85-92): "2 1537/1529 (60.5/60.2)"
Volkswagen Jetta (GLI, GL) (85-92): "2 1537/1529 (60.5/60.2)"

HP 1275 HP Spridget Level 2 Only

#36518 from Darryl Saylor · Rule change · TB 24-09 (2024-09 Fastrack)

fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.

In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows:
"(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows:
"(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"

HP Request for Classification of 1989-1994 Suzuki Swift GT 16V Twin

#36858 from Jorge Fabian · Rule change · TB 24-11 (2024-11 Fastrack)

neutralSuzuki Swift GT 89-94 newly classified to HP Pre at 1900 lbs, 1298cc DOHC fuel injected.

In HP Spec Lines, Classify Suzuki Swift GT (89-94) as follows:

A specification table follows in the original; it is not shown here.

HP MINI Cooper Spec Line Correction - Rear Brake Rotor Diameter

#37176 from Robert Bax · Rule change · TB 24-12 (2024-12 Fastrack)

neutralHP Mini Cooper 02-06 rear brake rotor increases from 239/9.4 mm/in to 259/10.2.

In HP Spec Lines, Mini Cooper (02-06), change Brakes Std.mm/(in.) as follows:
"(F) 276/(10.9) Vented Disc (R) 239/(9.4) 259/(10.2) Solid Disc"

HP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line

#37119 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)

fasterEP BMW 325i/is E30 (84-91) weight reduced 50–52 lbs across three spec lines to 2150, 2204, 2258.

In EP SPEC LINES, BMW 325i/is (E30) (84-91), change Weight as follows:
"2200 2150
*2255 2204
**2310 2258"

HP Request to Update 1988-1991 Civic to Match 1988-1991 CRX

#37444 from ENRIK BENAZIC · Rule change · TB 25-01 (2025-01 Fastrack)

fasterHP Honda Civic 1.5 88-91 weight reduced to 2175 lbs base, 2229 lbs with one asterisk, 2284 lbs with two asterisks.

In HP SPEC LINES, Honda Civic 1.5 (88-91), change Weight as follows:
"2245 2175
*2301 2229
**2357 2284"

HP Effective date for Jan 2025 GCR updates

#37654 from Doug Piner · Rule change · TB 25-02 (2025-02 Fastrack)

slowerEP BMW Z3 2.5L requires 52mm flat plate intake restrictor; Z3 2.8L 55mm; 328i/is E36 58mm; 328i/ci E46 58mm; 325i/is E46 56mm; 325i/is E36 56mm; 325is M-Technic 56mm.

In EP Spec Lines, add to Notes as follows:
BMW Z3 2.5LL "(Effective 2/21/2025) 52mm Flat Plate Intake Restrictor is required."
BMW Z3 2.8L (97-00): "(Effective 2/21/2025) 55mm Flat Plate Intake Restrictor is required."
BMW 328i/is E36 (96-99): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required."
BMW 328i/ci E46 (01-06): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required."
BMW 325i/is E46 (01-06): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."
BMW 325i/is E-36 (92-95): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."
BMW 325is M-Technic (1994): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."

HP Request Competition Adjustment to BMW Z3 2.5L

#37120 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)

slowerEP BMW Z3 and 3-series models get smaller intake restrictors: Z3 2.5L to 52mm, Z3 2.8L to 55mm, 328i to 58mm, 325i to 56mm.

In EP Spec Lines, change Notes as follows:
BMW Z3 2.5LL "(Effective 3/1/2025) 56mm 52mm Flat Plate Intake Restrictor is required."
BMW Z3 2.8L (97-00): "(Effective 3/1/2025) 59mm 55mm Flat Plate Intake Restrictor is required."
BMW 328i/is E36 (96-99): "(Effective 3/1/2025) 62mm 58mm Flat Plate Intake Restrictor is required."
BMW 328i/ci E46 (01-06): "(Effective 3/1/2025) 62mm 58mm Flat Plate Intake Restrictor is required."
BMW 325i/is E46 (01-06): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required."
BMW 325i/is E-36 (92-95): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required."
BMW 325is M-Technic (1994): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required."

HP Interpretation of Production Rules on Mirrors

#37235 from Lawrence Slivinski · Rule change · TB 25-03 (2025-03 Fastrack)

neutralEP, FP, HP: interior or exterior mirrors meeting rule 9.3.36 now permitted.

In GCR, add new rule as Section 9.1.5.E.10.f:
"Any interior or exterior mirror(s) that meets rule 9.3.36 may be used."

HP HP Class Adjustments

#37459 from Production Committee · Rule change · TB 25-01 (2025-01 Fastrack)

slowerHP Mazda 2 11-14 base weight up 50 lbs to 2045; all VW 80s models up 50 lbs to 2150 base.

In HP SPEC LINES, change Weight as follows:
Mazda 2 (11-14)
"(Effective 3/1/2025) 1995 2045
*2045 2096
**2095 2147"
Volkswagen Golf (GTI, GT, GL) (85-92)
"(Effective 3/1/2025) 2100 2150
*2153 2204

Show 13 more lines

**2205 2258"
Volkswagen Jetta (GLI, GL) (85-92)
"(Effective 3/1/2025) 2100 2150
*2153 2204
**2205 2258"
Volkswagen Rabbit 1780
"(Effective 3/1/2025) 2100 2150
*2153 2204
**2205 2258"
Volkswagen Scirocco 1780 (8-valve) (83-88)
"(Effective 3/1/2025) 2100 2150
*2153 2204
**2205 2258"

HP Weight Reduction for Honda S2000

#37466 from Michael Unger · Rule change · TB 25-03 (2025-03 Fastrack)

fasterEP Honda S2000 1997cc base loses 75 lbs to 2375; 2157cc base loses 60 lbs to 2450.

In EP, Spec Lines make the following weight changes:

A specification table follows in the original; it is not shown here.

HP Mazda 1999 Miata 1.8L

#37488 from Joe Carr · Rule change · TB 25-03 (2025-03 Fastrack)

fasterEP Mazda MX-5/Miata 99-05 minimum weight drops to 2100 lbs, 2153 lbs with power adder, 2205 lbs with two adders.

In EP Spec Lines, make the following weight change:
Mazda MX-5 /Miata (99-05):
"2150 2100
*2204 2153
**2258 2205"

HP MINI Cooper (07-13) Spec Line Correction: Errors and Omissions

#37560 from Robert Bax · Rule change · TB 25-03 (2025-03 Fastrack)

slowerHP Mini Cooper 07-13 engine corrected to DOHC; valve lift limit reduced to 0.390 inches.

In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), change as follows:
Engine Type:
"4 Cyl
SOHC DOHC"
Notes:
"Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."

HP Request for Classification of Chevrolet Spark

#37755 from Kristian Smith · Rule change · TB 25-04 (2025-04 Fastrack)

neutralChevrolet Spark 16-22 classified HP Pre at 1850 lbs minimum weight, fuel injected, 1399 cc.

In HP Spec Lines, classify the Chevrolet Spark (16-22):

A specification table follows in the original; it is not shown here.

HP Request to Lower Ford Festiva Minimum Weight to 1600 LBS

#37939 from Doug DeRonne · Rule change · TB 25-04 (2025-04 Fastrack)

fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.

In HP Spec Lines "Ford Festiva (88-93)" change as follows:
Weight:
"1700 1600
*1743 1640
**1785 1680"
Notes:
"Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."

Oregon 2025 → Oregon 2026 2025-05-10 to 2026-05-09

HP Base Weight Adjustment for H-Production X1/9 Spec Lines

#38255 from Matthew Brannon · Rule change · TB 25-06 (2025-06 Fastrack)

fasterHP Fiat X-1/9 base weights reduced 50–53 lbs across 1300 and 1500 spec lines.

In HP Spec Lines, change Weight as follows:
Fiat X-1/9 & Bertone1500: “1790 1740 *1835 1784 **1880 1827”
Fiat X-1/9 1300: “1650 1600 *1691 1640 **1733 1680”
Fiat X-1/9 1300: “2060 2010”
Fiat X-1/9 1500: “1950 1900”

HP BMW Z4 update

#38490 from Bryce McGuire · Rule change · TB 25-07 (2025-07 Fastrack)

slowerEP BMW Z4 03-05 restricted to 52mm flat plate intake restrictor.

In EP Spec Lines, BMW Z4 (03-05), add to Notes the following:
“52mm Flat Plate Intake Restrictor.”

HP EP Fiat 124 Spider Competition Adjustment Request

#38498 from John Baucom · Rule change · TB 25-07 (2025-07 Fastrack)

fasterEP Fiat 124 Spider 1600 & 2000 weight drops 50 lbs to 2000; carburetors gain 2mm chokes to 36mm.

In EP Spec Lines, Fiat 124 Sport Spider 1600 & 124 Spider 2000, change as follows:
Weight: "2050 2000"
Carburetor No. & Type: "(2) Weber 40 IDF-40IFI, (2) Solex C40P116, 34 36mm choke(s) req’d, (2) Weber 45DCOE w/ 34 36 mm
choke(s) on I.R. manifold or fuel injection."

HP HP Plymouth Arrow spec omission

#38995 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

neutralHP Plymouth Arrow transmission max speeds clarified to 4 or 5.

In HP Spec Lines, Plymouth Arrow (76-80), add the following wording to Trans. Speeds(max):
"4 or 5"

HP Add Wheel Diameter to Appendix G

#39008 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

neutralEP, FP, HP wheel diameter added to Appendix G as absolute maximum specification.

In Appendix G.2.3, change as follows:
"Rim width and diameter are is absolute maximums."

HP Add TB ID tolerance to general Prod rules

#39009 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

neutralEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.

In GCR, Section 9.1.5.E., change as follows:
9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain
stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished."
9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must
remain stock (tolerance of +/-.25mm)."

HP Please Lower Weight of 280Z

#38871 from Matthew Miller · Rule change · TB 25-09 (2025-09 Fastrack)

fasterEP Nissan 280Z minimum weight reduced from 2560 to 2400 lbs.

In EP Spec Lines, Nissan 280Z, change Weight (lbs) as follows:
"(Effective 11/1/2025) 2560 2400
*2624 2460
**2688 2520"

HP Miata Weight Adjustment Follow Up

#38949 from Don Tucker · Rule change · TB 25-10 (2025-10 Fastrack)

fasterEP Mazda MX-5 1.8L 90-97 weight reduced to 2125 lbs from 2150 lbs.

In EP Spec Lines, Mazda MX-5 / Miata 1.8L (90-97), Effective 11/1/2025 make the following weight change:
"2150 2125"

HP Weight Break for 1098 Midget / Sprite

#38970 from Kendall Jones · Rule change · TB 25-10 (2025-10 Fastrack)

fasterHP Austin-Healey Sprite/Midget 1098cc minimum weight drops 80 lbs to 1550.

In HP Spec Lines, Austin-Healey Sprite/Midget 1098cc, Effective 11/1/2025make the following weight change:
"1630 1550"

HP HP Volvo 142 spec omission

#38994 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".

In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes:
"Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."

HP HP Mini DOHC 1.6

#38996 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".

In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following
changes to the Notes:
"Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."

HP Add to Rabbit description

#39019 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

neutralFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.

In FP Spec Lines, make the following spec line correction:
"Volkswagen Rabbit (Includes Convertible Cabriolet)"
In HP Spec Lines, make the following spec line correction:
"Volkswagen Rabbit 1588 (Includes Cabriolet)"
"Volkswagen Rabbit 1715 (Includes Cabriolet)"
"Volkswagen Rabbit 1780 (Includes Cabriolet)"

HP Clean-up 9.1.5.E.7e

#39025 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

neutralEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.

In GCR, Section 9.1.5.E.7., change as follows:
"e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes
Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear
disc brakes under this rule. When converting from rear drum brakes to rear disc brakes:
1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on
the vehicle’s spec line.
2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and
alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock

Show 3 more lines

from converting to rear disc brakes under this rule.
3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes
as stock from converting to rear disc brakes under this rule."

HP Add TB size to Ford Mustang (94-98) Spec Line

#39130 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

neutralEP Ford Mustang (94-98) fuel injected throttle body inside diameter specified at 60.

In EP Spec Lines, Ford Mustang (94-98) add the following to the Fuel Injected Equipped Throttle Body Inside Diameter column:
"60"

HP Request to Re-Classsify Datsun SPL-311 to HP from FP

#39116 from Robert Heatwole · Rule change · TB 25-12 (2025-12 Fastrack)

neutralDatsun SPL-311 newly classified to HP at 2050 lbs with 1595cc OHV iron engine and specified carburetors.

In HP Spec Lines, classify Nissan/Datsun SPL 311 as follows:

A specification table follows in the original; it is not shown here.

HP TR2 Notes E&O

#39180 from Anthony Parker · Rule change · TB 25-12 (2025-12 Fastrack)

unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.

In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes:
"Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990
lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."

HP Balance of Power

#39187 from Jim Simaras · Rule change · TB 25-12 (2025-12 Fastrack)

slowerEP BMW Z3 2.5L restrictor reduced 52mm to 50mm, weight increased to 2550 lbs base; five other BMW models get smaller restrictors.

In EP Spec Lines, make the following changes to Restrictors:
BMW Z3 2.5L: "52mm 50mm Flat Plate Intake Restrictor"
BMW Z3 2.8L (97-00): "55mm 53mm Flat Plate Intake Restrictor"
BMW 328i/is E36 (96-99): "58mm 55mm Flat Plate Intake Restrictor"
BMW 328i/ci E46 (01-06): "58mm 55mm Flat Plate Intake Restrictor"
BMW 325i/is (E46) (01-06): "56mm 53mm Flat Plate Intake Restrictor"
BMW 325is M-Technic (1994): "56mm 53mm Flat Plate Intake Restrictor"
BMW 325i/is E-36 (92-95): "56mm 53mm Flat Plate Intake Restrictor"

Show 4 more lines

In EP Spec Lines, BMW Z3 2.5L, change Weight as follows:
"2500 2550
*2563 2614
**2625 2678"

HP Alternative BOP Request for 84-87 Honda CRX/Civic

#39223 from Bill Lamkin · Rule change · TB 25-12 (2025-12 Fastrack)

fasterHP Honda Civic and CRX models get wider 13-inch wheels: 6 to 7 inches.

In HP Spec Lines, change Wheels as follows:
Honda Civic: "13 x 6 7"
Honda Civic DX (92-95): "13 x 6 7"
Honda Civic/Si (84-87): "13 x 6 7"
Honda Civic 1.5 (88-91): "13 x 6 7"
Honda CRX/Si (84-87): "13 x 6 7"
Honda CRX 1.5(88-91): "13 x 67"

HP E/O: Improve Consistency of the Spec Lines

#39500 from Robert Bax · Rule change · TB 26-01 (2026-01 Fastrack)

unclearHP Toyota MR-2 1.6L (85-89) compression ratio set to 11.0:1.

In HP Spec Line, Toyota MR-2 1.6L (85-89), change Comp. Ratio as follows:
"11.0:1"

HP Request to Reclassify BMW 2002 Into H Production

#39567 from Jonathan Kinberg · Rule change · TB 26-01 (2026-01 Fastrack)

neutralBMW 2002 newly classified to H Production at 2350 lbs with 1990cc iron block, 40 DCNF carburetor, 11.0:1 compression.

In HP Spec Lines, classify BMW 2002, as follows:

A specification table follows in the original; it is not shown here.

HP Triumph Spitfire 1296cc Compression Ratio Increase to 12:1

#39589 from Neil Verity · Rule change · TB 26-02 (2026-02 Fastrack)

fasterHP Triumph Spitfire 1296cc compression ratio increases from 11.0 to 12.0:1.

In HP Spec Lines, make the following spec line changes:
Triumph Spitfire:
Carburetion
"Valves: (I) 33.0/(1.30) (E) 29.7/(1.17)
Comp. ratio 11.0 12.0:1, Valve lift .450”
Trans. Speeds: 4"
Triumph Spitfire Mk. III & IV 1500:
Carburetion

Show 5 more lines

"1300 Valves: (I) 33.0/(1.30) (E) 29.7/(1.17)
1500 Valves: (I) 36.6/(1.44) (E) 29.7/(1.17)
1300: Comp. ratio 12.0:1, Valve lift .450”
1500: Comp. ratio 11.0:1, Valve lift .450”
Trans. Speeds: 4"

HP Clarification On Oil Cooler Ducting

#39604 from Chuck Allard · Rule change · TB 26-03 (2026-03 Fastrack)

neutralHP class mid and rear engine cars may add single inlet and outlet holes for oil cooler ducting in front bodywork.

In GCR, Section 9.1.5.E.6.g.4, add the following:
"On mid and rear engine cars, a single inlet hole may be cut in the front bodywork and a single outlet hole may be cut in the front
trunk floor or a wheel well, for the sole purpose of ducting air to a single engine oil cooler. The size of these holes may be no
larger than the area of the oil cooler itself."

HP Honda Fit 2015-19 Error in Engine Classification

#39853 from Jose Fabian · Rule change · TB 26-03 (2026-03 Fastrack)

neutralHP Honda Fit 2015-19 engine reclassified from SOHC to DOHC.

In HP Spec Lines, Honda Fit (15-19), change Engine Type Mat’l Block/Head as follows:
"4 Cyl. SOHC DOHC"

HP Miata track width - errors and omissions

#39976 from Production Committee · Rule change · TB 26-05 (2026-05 Fastrack)

neutralEP Mazda MX-5 94-97 front track widens to 1516 mm (59.7 in.), rear to 1534 mm (60.4 in.).

In EP Spec Lines, Mazda MX-5 / Miata (94-97), change Track (F/R) mm/(in.) as follows:
Track (F/R) mm/(in.): "1483/1509 (58.4/59.4) 1516/1534(59.7/60.4)"

HP Triumph GT6 Spec Change.

#40098 from Anthony Parker · Rule change · TB 26-05 (2026-05 Fastrack)

fasterEP Triumph GT6 auto-type drivetrain choke increases from 44mm to 45mm.

In EP Spec Lines, Triumph GT6, change the "Drivetrain Notes" as follows:
"(2) auto-type w/44 45mm choke(s)"

HP Request to Classify BMW E21 320i

#40110 from Doug DeRonne · Rule change · TB 26-05 (2026-05 Fastrack)

neutralBMW 320i/is E21 (80-83) newly classified in HP Spec Lines.

In HP Spec Lines, classify BMW 320i/is (E21) (80-83) as follows:

HP BMW 318is 84-85 engine displacement correction

#40116 from Production Committee · Rule change · TB 26-05 (2026-05 Fastrack)

neutralHP BMW 318is 84-85 displacement corrected from 1797 to 1767 cc.

In HP Spec Lines, BMW 318i/is E30 (84-85), change Displacement Bore x Stroke mm/ (in.) as follows:
"1797 1767 89.0 x 71.0 (3.50x2.80)"

What the rules allowed changed as listed; this does not say what any particular car ran.