AS + FE2 + P2 + FF at Michelin Raceway Road Atlanta

2023-04-01 P2 Remove redundant effective date language and update engine table

#34012 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, change as follows:

2023-04-01 P2 E&O - Correct dimensional equivalents

#34038 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.2, change as follows:
"Height: No part of the vehicle having special or significant aerodynamic function shall exceed a height of 115cm (45.275 inches)
above the ground with the car in normal racing trim, driver aboard."
In P2, GCR section 9.1.8.C.D.3, change as follows:
"However, no portion shall extend more than 10cm (3.937 inches) beyond a plane tangent to the outer face of the front and rear
wheels with tires."
P2 Engine Table
Spec

A specification table follows in the original; it is not shown here.

2023-05-01 P2 Clarify minimum side body height requirement

#34143 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.6, change as follows:
"As viewed from the side, T the outermost surface of side pods body between the front and rear wheel openings and above the
floor must have a minimum height equal to the height of the front axle centerline."

2023-05-01 P2 Clarify closed cockpit single seat car allowance

#34144 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.C, add a section as follows:
"4. Closed cockpit single seat cars are not permitted unless specifically allowed by a spec line in Table 1."

2023-08-01 AS Crate Motor Part Numbers

#32944 from Sam Daniels · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

As printed in Fastrack

In AS, GCR Section 9.1.6.F.2., change as follows:
"GM Performance parts CT400 P/N-1937 → 0604 or 1937 → 0604 engine assembly for GM produced vehicles."

2023-08-01 AS Request wheel size change

#33007 from Michael Kamalian · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT 5.0l (15-17) Restricted Preparation, change Notes as follows:
"Max. Wheel Size: Dia.18.0 19.0 inches."

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2023-08-01 AS Alternative Upper Front Control Arms for Dodge Challenger

#33352 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

As printed in Fastrack

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"SPC-66045 Alternate front upper control arms are permitted."

2023-08-01 AS Front Brake Caliper Adapters for Dodge Challenger

#33353 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

As printed in Fastrack

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"Stock brakes or alternate Dodge brakes (Part numbers: front caliper (0517 → 5106 (R) and 0517 → 5107 (L); rear caliper (R1542564 (R)
and R1542565 (L))) may be used with the brake rotor sizes listed in this specification line. Alternate brackets may be used to
facilitate updated/backdated components."

2023-12-01 P2 Correct Table 1 for Engine Date Range Specifications

#35182 from Formula/Sports Racing Committee · Rule change · TB 23-12 (2023-09 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 P2 E&O - Clarify B.1 modified engine range in AMAC spec lines

#35225 from Club Racing Board · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 FF Honda Fit Oversize Piston Rings

#35305 from Doug Learned · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In FF, GCR section 9.1.1.B.14.e.3.a, add the following:
"The standard ring pack, PN 13011-RB1-004 (Riken) or 13011-RB1-006 (Nippon), or the oversize ring pack, PN 13021-RB7-Z01
(Riken), or 13021-RB7-Z02 (Nippon), or FF800-100 (Fast Forward), may be used."

2024-01-01 P2 Replacement Engine Crankcase for 07/08 Suzuki GSX-R1000 Engines

#35340 from Michael A Reupert · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, add to notes as follows:
"No modifications allowed on engines manufactured after 2008 model year. 2007-2008 Suzuki GSX-R1000 crankcase part
#11300-21860 may be replaced with 2016-2019 Suzuki GSX-S1000 crankcase part #11301-04840."

2024-03-01 AS Request to Classify 1970-1981 Camaro and Firebird in AS

#33659 from Brandon Vivian · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, classify Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep as follows:
AS Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:

A specification table follows in the original; it is not shown here.

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2024-03-01 AS Fuel Cell 12

#34194 from Clark Cambern · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, add to Notes as follows:
Cadillac CTS-V (04-07): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken
from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24
inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with

2024-03-01 AS Please Classify the 6th Gen Into AS.

#35448 from Daniel Richardson · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, classify Chevrolet Camaro (16-) Full Prep as follows:
AS
Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:

A specification table follows in the original; it is not shown here.

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2024-03-01 AS spec lines

#35713 from American Sedan Committee · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, classify Ford Mustang GT (05-14) with Restricted prep Engine as follows:
AS
Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-04-01 AS Restricted Prep Aftermarket Parts Request

#35682 from Tom Aquilante · Rule change · TB 24-04 (2024-04 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."
In AS Spec Lines, Pontiac GTO (04-06), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2024-04-01 AS Allowance of 11

#35824 from American Sedan Committee · Rule change · TB 24-04 (2024-04 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Cadillac CTS-V (04-07), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Chevrolet Camaro SS (V8) (10-15), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Dodge Challenger (08-20), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Ford Mustang GT 5.0l (15-17), add to Notes the following:
"11" wide wheels can be used until 3/1/25."

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-05-01 AS 6th gen Camaro limited prep

#35733 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, classify Chevrolet Camaro 1LE (2016-) as follows:
AS Wheelbase Gear Ratios Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs.) Notes:
Chevrolet
Camaro, 1LE

A specification table follows in the original; it is not shown here.

2024-05-01 AS Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V8 LS1 Alum BLK

#35825 from Desi Colon · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, classify Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves
per cylinder, as follows:
AS Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

2024-05-01 P2 CN Spec ECU

#35835 from Bart Wolf · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line E, change the notes as follows:
"No engine modifications except for dry sump oil system, ECU mapping, and exhaust system the following: oil system, ECU, and
exhaust are unrestricted."

2024-05-01 AS Full Prep Head

#35891 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (82-92), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet Camaro (10-15), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86), add to Notes the following:
"Flo Tek Part # 203-500 are permitted."

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-05-01 P2 E&O - Correct FIA Group CN spec line notes

#35900 from Club Racing Board · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, FIA Group CN spec line, change the notes as follows:
"FIA Group CN homologated chassis, brake calipers and discs, hub carriers, and suspension components are required. V de
V European Proto Endurance Series Challenge permitted bodywork, rear diffuser, wing, wheels, and assisted
shifting are allowed. Car M must comply with all other P2 requirements. Competitors must have copies of FIA Group CN
Technical Regulations and V de V European Proto Endurance Series Challenge Sporting and Technical Regulations in their
possession and present them upon request are available here: https://www.scca.com/pages/technical-forms-and-downloads."

2024-06-01 AS Request for Classification of 2018-2023 mustang In

#35764 from Michael Kamalian · Rule change · TB 24-06 (2024-06 Fastrack)

Summary

As printed in Fastrack

AS Spec Lines, classify Ford Mustang GT 5.0L (2018-) as follows:
AS Wheelbase Gear Ratios

A specification table follows in the original; it is not shown here.

2024-09-01 AS Mustang transmission ratios

#36662 from American Sedan Committee · Rule change · TB 24-09 (2024-09 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Notes as follows:
"Alternate transmission Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68.”
In AS Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows:
"Alternate transmission Ratios 3.24, 2.10, 1.42, 1.00, 0.81, .062."

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-10-01 FF Update to FF EGR Blanking Plate Rule

#36633 from Matt Boian · Rule change · TB 24-10 (2024-10 Fastrack)

Summary

As printed in Fastrack

In FF, GCR section 9.1.1.B.14.r.1, change as follows:
"All emission control devices must be removed and blocked off by the blanking plate provided by HPD or Fast Forward as noted
below, except for the VTEC activation valve. The VTEC activation valve must be retained; and it must be functioning. No
modifications are permitted.
a. EGR Plate: Fast Forward PN: FF200-301.
b. EGR Port Cover: Fast Forward PN: FF200-302."

2024-11-01 FF Change FF/FC Weight with Sequential Gearbox

#36651 from Robert Wright · Rule change · TB 24-11 (2024-11 Fastrack)

Summary

As printed in Fastrack

In FF, GCR section 9.1.1.B.20.A.3, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
In FC, GCR section 9.1.1.B.20.B.4, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."

2024-11-01 FF Alternative Oversize Honda Fit Pistons

#37064 from Formula/Sports Racing Committee · Rule change · TB 24-11 (2024-11 Fastrack)

Summary

As printed in Fastrack

In FF, GCR section 9.1.1.B.14.e.1, change as follows:
"Honda Fit OEM standard size pistons, PN: 13010-RB1-000, or Honda Fit OEM 0.25mm oversize pistons, PN: 13020-RB7-Z00, or
Fast Forward 0.25mm oversize pistons, PN: FF800-110, may be used."
In GCR section 9.1.1.B.14.e.2, change as follows:
"a. Maximum standard piston diameter, measured at a point 16mm from the bottom of the skirt: 73.240mm
(2.8834 2.8835 inches).
b. Centerline of wrist pin to crown maximum: 26.21mm (1.032 inches).
c. Maximum overall height from skirt to crown edge: 47.80mm (1.882 inches).

2024-12-01 P2 2000 cc Pinto Engine Car Weight

#37187 from Marvin Hodges · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Line E Note 2, add the following:
"8. Minimum weight 1335 lbs."

2025-01-01 AS Increase Coyote Engine Restrictor to 80mm

#36177 from Gregory Eaton · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, add to Notes as follows:
Ford mustang (GT 05-14): "Gen 1- 67mm Gen 2-64mm"
Ford mustang (GT 05-14): "Gen 1- 67mm"
Ford mustang (GT 15-17): "Gen 1- 67mm"
Ford mustang (GT 94-04): "Gen 1- 67mm Gen 2-64mm"
Ford mustang cobra & Cobra R Mercury Capri (79-93) (79-86): "Gen 1- 67mm Gen 2-64mm"

2025-01-01 AS Performance Pack for 2015+ Mustang

#36867 from Michael Kamalian · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang Coupe GT (05-14) Restricted Prep., change Notes as follows:
"The 4.6L engine assembly has a weight reduction of 300 lbs. 5.0L/6spd engine/trans: track pack front and rear spoiler allowed."
In AS Spec Lines, Ford Mustang Coupe GT (05-14) with Restricted Prep. engine, change Notes as follows:
"Max. Wheel Size: Dia.18.0 inches. Stock brakes or alternate Ford 14” Brembo Brake (Ford Racing Kit #M-2300-S) and full prep
brake package may be used. Either engine may be used. 1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l
Coyote 15-17 61mm FPR Cold Air Intake allowed Charge Motion Control Valves can be blocked off and removed for firewall
clearance Allow Cold Air Intake Tremec Magnum transmission may be used P/N- TUKT16901. Full Prep Transmissions rule
package may also be used. Max compression ratio, 11.2:1 track pack front and rear spoiler allowed. Alternate transmission

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2025-01-01 AS Gear Ratios

#37131 from Timothy White · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, change Gear Ratios as follows:
Cadillac CTS-V (04-07):
"2.97, 2.07, 1.43,1.00, 0.84,0.56 or 3.01, 2.07, 1.43, 1.0, .84, .57 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Full Prep:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Restricted Prep.:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet/Pontiac Camaro & Firebird (82-92) Full Prep:

2025-01-01 AS ECU specs for LS engine

#37208 from Gary Mathews · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In AS SPEC LINES, Cadillac CTS-V (04-07) Restricted Prep., change Notes as follows:
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Tremec TR6060
Transmission with 3.0 1, 2.07, 1.43, 1.0, .84, .57 ratios permitted. 11” wide wheels can be used until 3/1/25. Any ECM may be
used."
In AS SPEC LINES, Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep ., add to Notes as follows:
"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1, add to Notes as follows:

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2025-03-01 FF Formula F Proposal to Invite Older Cars Via a Tire Rule Change

#37802 from Anthony Stefanelli · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Formula F shall be limited to the following tires (front tires may not be used as rears):
Dries:
Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13
Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13
Wets:
Front - Hoosier Wet or W3 Radial 44421 185/60R13
Rear - Hoosier Wet or W3 Radial 44426 205/60R13

2025-03-01 AS Race memo

#37902 from American Sedan Committee · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, change Notes as follows:
Cadillac CTS-V (04-07) Restricted Prep. 6.0L V8 (Aluminum block, Aluminum heads), LS2, 2 valves/cylinder:
"Any ECM maybe used."
Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep. 6.2L V8 (Aluminum Block, Aluminum Heads), 2 valves per cylinder:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (82-92)s 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves per cylinder:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (93-02):

2025-04-01 AS Flotek Head Plunge Cut Inconsistencies

#37502 from Pamela Richardson · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.6., replace Figure 1 Value Seat Cutting Dimensions with the following:

2025-04-01 AS Notes clean up

#37693 from American Sedan Committee · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, change/add to Notes as follows:
Cadillac CTS-V (04-07):
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used. The
Drive Shaft Shop, Axle shaft part #'s 510220/510221 permitted."
Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #s: 14101081, 14014416 Port Volume (Max.): 081
casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb. weight reduction. Edelbrock Cylinder Head Part

2025-04-01 FE2 Driver Safety & Comfort

#37965 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

As printed in Fastrack

In FE2, GCR section 9.1.1.G.2.E, add the following:
"g. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

2025-05-01 AS Errors and Omission

#38055 from American Sedan Committee · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT 5.0l (15-17), Flat Plate Restrictor Size, change as follows:
"67mm 64mm"

2025-05-01 AS Request to Add LS1/LS6 Intakes for 5.3L Truck Engine EnO

#38197 from Jim Clark · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.6.F., add the following to Intake Part #’s:
"17113697, 19418185, 89017230, 89017363, 89017364, and 89017365, 12561269 and 88894095"

2025-05-01 FF Page 228, FF tire rule 9.1.1.10.e

#38251 from Anthony Stefanelli · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

As printed in Fastrack

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Formula F shall be limited to the following tires (front tires may not be used as rears):
Dries:
Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13
Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13
Wets:
Front - Hoosier Wet or W3 Radial 44421 185/60R13
Rear - Hoosier Wet or W3 Radial 44426 205/60R13

2025-06-01 AS Errors and Omissions

#38234 from American Sedan Committee · Rule change · TB 25-06 (2025-06 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Gear Ratios the following:
"or 3.66, 2.43, 1.69, 1.32, 1.00, .65"

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2025-07-01 AS RE: Previous Letter 37695 Update

#38245 from Michael Kamalian · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT 5.0 (2018-), change Weight as follows:
"3600 3525"

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton

2025-10-01 FE2 FE & FE2 Bubble Tail

#38978 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

As printed in Fastrack

In FE, GCR section 9.1.1.G.2.F.k, change as follows:
"Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."

2025-11-01 AS Cadillac CTS-V BOP Weight Change

#38640 from Alex Lozano · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Cadillac CTS-V (04-07) Restricted Prep., change Weight as follows:
"(Effective 11/1/2025) 3450 3400"

2025-12-01 AS 1994 Mustang Spec Line Request

#39104 from Barry Borgschatz, Jr · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT(94-04) with Restricted Prep Engine, add to notes the following:
"Ford Motorsport #M-6250-F303 camshaft is permitted."

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2026-01-01 FF Formula F Alternative Tire Rule Proposed Clarifications

#39281 from Jay Messenger · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Alternatively, Formula F cars with rocker arm suspension (e.g., 1987-90 Reynard, Swift DB1,) and/or outboard suspension on at
least one chassis end homologated in 1989 or earlier with any combination of rocker arm or outboard suspension on all four
corners (e.g., 1987 – 1990 Reynard, Swift DB1) may use the following alternative tires. Note: This rule is intended to allow older
cars with the described suspension design to use the alternative tires. It is not to be exploited by modifying cars with push-rods or
pull-rods to meet the above requirements or by modifying either end of older cars to push- or pull-rod suspension to be eligible to
run the alternative tires. Cars that were homologated in 1989 or earlier with push- or pull-rod suspension on no more than two
corners may seek approval to run the alternative tire by utilizing the compliance process outlined in GCR section 8.1.4."

2026-01-01 AS Restrictor Plate Change for Gen 2 Ford Coyote Engine

#39501 from American Sedan Committee · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, change Restrictor as follows:
Ford Mustang Incl. Cobra and Cobra R (79-93) and Mercury Capri (79-86) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang GT (94-04) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang Coupe GT (05-14) Restricted Prep 5.0L/6 speed 4 valves per cylinder: "64 mm 61 mm"
Ford Mustang GT (05-14) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang GT 5.0L (15-17) Restricted Preparation: "64 mm 61 mm"

2026-02-01 AS Edelbrock manifold (& timing kit) to Chevy LS Spec Lines Request

#39055 from Jason Smith · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.6.D.2.h.2., add the following:
"(Effective 2/1/2026) i. Weight based on full preparation chassis choice spec line for GM LM7 5.3L
Carburetor Option:
Must use the full prep 4776 holly carburetor and spacer gasket
Edelbrock Performer RPM 71187 intake manifold
MSD 6014 ignition box
(Edelbrock part # kit 7118)"

2026-03-01 AS Re-Organization of AS Spec lines for 2026

#39887 from American Sedan Committee · Rule change · TB 26-03 (2026-03 Fastrack)

Summary

As printed in Fastrack

This AS Spec Lines re-organization simplifies the Spec Lines for all drivers. This version gives the chassis information on what
engines can be put in their cars. It removes information that is now repeated in the ruleset and adds engine/weight combos as
well as wheelbase/tire size information. The Notes in the Spec Lines have been reviewed to remove information now listed in
the engine build sheets and retain information pertinent to the chassis selected. Where there is nothing in the notes, it is not an
error. It just means everything a driver needs is now in the main rules or the build sheets.
In AS Spec Lines, delete current Spec Line in its entirety as follows:

A specification table follows in the original; it is not shown here.