AS + P2 + FE2 + FP at Michelin Raceway Road Atlanta

2023-04-01 P2 Remove redundant effective date language and update engine table

#34012 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, change as follows:

2023-04-01 P2 E&O - Correct dimensional equivalents

#34038 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.2, change as follows:
"Height: No part of the vehicle having special or significant aerodynamic function shall exceed a height of 115cm (45.275 inches)
above the ground with the car in normal racing trim, driver aboard."
In P2, GCR section 9.1.8.C.D.3, change as follows:
"However, no portion shall extend more than 10cm (3.937 inches) beyond a plane tangent to the outer face of the front and rear
wheels with tires."
P2 Engine Table
Spec

A specification table follows in the original; it is not shown here.

2023-05-01 FP Classification Request for 1978 Toyota Celica

#34097 from Bob Pharr · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, classify Toyota Celica (78-80) as follows:

A specification table follows in the original; it is not shown here.

2023-05-01 P2 Clarify minimum side body height requirement

#34143 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.6, change as follows:
"As viewed from the side, T the outermost surface of side pods body between the front and rear wheel openings and above the
floor must have a minimum height equal to the height of the front axle centerline."

2023-05-01 P2 Clarify closed cockpit single seat car allowance

#34144 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.C, add a section as follows:
"4. Closed cockpit single seat cars are not permitted unless specifically allowed by a spec line in Table 1."

2023-06-01 FP Request to Classify Sonic and Fiesta in HP

#34264 from Greg Amy · Rule change · TB 23-06 (2023-05 Fastrack)

Summary

As printed in Fastrack

In HP, adjust model years of the "Ford Fiesta (11-16)" spec line as follows:
"Ford Fiesta (11-16 9)"
In FP, adjust model years of the "Chevrolet Sonic (12-16)" spec line as follows:
"Chevrolet Sonic (12-16 9)"

2023-07-01 FP ITC to FP?

#34286 from David Snow · Rule change · TB 23-06 (2023-07 Fastrack)

Summary

As printed in Fastrack

In HP Spec Lines, Volkswagen Rabbit Cabriolet 1780, delete in its entirely:
In HP, Spec Lines, Volkswagen Rabbit, change Title as follows:
“Volkswagen Rabbit 1588 (includes Cabriolet / convertible)”
“Volkswagen Rabbit 1715 (81-84) (excl. conv.)”
“Volkswagen Rabbit GTI 1780 (83-84)”

2023-07-01 FP Correct Intake Valve Size on 1500cc Midget/Spitfire

#34419 from Production Committee · Rule change · TB 23-06 (2023-05 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change Intake Valve Size as follows:
"(I) 36.65.3/(1.44)"
In FP Spec Lines, Triumph Spitfire Mk. IV & 1500, change Intake Valve Size as follows:
"(I) 36.65.5/(1.440)"
In HP Spec Lines, Triumph Spitfire 1500, change Intake Valve Size as follows:
"(I) 36.65.5/(1.440)"
In HP Spec Lines, Triumph Spitfire Mk. III & IV 1500, change Intake Valve Size as follows:
"(I) 36.65.5/(1.440)"

2023-08-01 AS Crate Motor Part Numbers

#32944 from Sam Daniels · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

As printed in Fastrack

In AS, GCR Section 9.1.6.F.2., change as follows:
"GM Performance parts CT400 P/N-1937 → 0604 or 1937 → 0604 engine assembly for GM produced vehicles."

2023-08-01 AS Request wheel size change

#33007 from Michael Kamalian · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT 5.0l (15-17) Restricted Preparation, change Notes as follows:
"Max. Wheel Size: Dia.18.0 19.0 inches."

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2023-08-01 AS Alternative Upper Front Control Arms for Dodge Challenger

#33352 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

As printed in Fastrack

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"SPC-66045 Alternate front upper control arms are permitted."

2023-08-01 AS Front Brake Caliper Adapters for Dodge Challenger

#33353 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

As printed in Fastrack

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"Stock brakes or alternate Dodge brakes (Part numbers: front caliper (0517 → 5106 (R) and 0517 → 5107 (L); rear caliper (R1542564 (R)
and R1542565 (L))) may be used with the brake rotor sizes listed in this specification line. Alternate brackets may be used to
facilitate updated/backdated components."

2023-12-01 FP Porsche 944/924S Rule Change Request

#35002 from Adam Achepohl · Rule change · TB 23-12 (2023-12 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, delete the Porsche 944/924S 2.5L (2V) (83-88) spec line entirely, and create a new spec line for Porsche
944/924S 2.5L(2V) 2.7L(2V) (83-89) as follows:

A specification table follows in the original; it is not shown here.

2023-12-01 FP FP and HP Toyota Corolla

#35030 from Keith Church · Rule change · TB 23-12 (2023-12 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, Toyota Corolla 2TC (71-74), change weight as follows:
"1853 1810"
In HP Spec Lines, Toyota Corolla (71-74), change weight as follows:
“1960 1910
* 2009 1958
** 2058 2006”

2023-12-01 FP Triumph GT6 Adjustments

#35054 from ANTHONY PARKER · Rule change · TB 23-12 (2023-12 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, Triumph GT6, change weight as follows:
"1830 1800"

2023-12-01 P2 Correct Table 1 for Engine Date Range Specifications

#35182 from Formula/Sports Racing Committee · Rule change · TB 23-12 (2023-09 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 FP FP data

#35060 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In FP Spec Line, Acura Integra LS (94-01), change weight as follows:
"2235 2260
*2291 2317
**2347 2373"
In FP Spec Line, Honda Del Sol VTEC (94-97), change weight as follows:
"2190 2265
*2245 2322
**2300 2378"

Applies to Acura Integra on this page: Ken Kannard, Les Chaney

Applies to Honda Civic Del Sol VTEC on this page: Cliff Ira

2024-01-01 FP Request to Review Z3 2.5 Spec Line

#35073 from Tim Schreyer · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In EP spec line, BMW Z3 2.5L, change weight as follows:
"2450 2500
*2511 2563
**2573 2625"

2024-01-01 P2 E&O - Clarify B.1 modified engine range in AMAC spec lines

#35225 from Club Racing Board · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 FP Corrections to Honda Spec Lines in FP

#35250 from Jonathan Spiegel · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, change Fuel Injected Equipped Throttle Body Inside Diameter as follows:
Acura Integra GSR (92-93): "58"
Honda Civic 1.5 (88-91): "NA 42"
Honda Civic EX (90-91): "55"
Honda Civic Si (88-91): “42 55”
Honda CRX 1.5 (88-91): “33 (primary) 42 (secondary) 42”
Honda CRX / CRX Si (84-87): ”42 33 (primary) 42 (secondary)”
Honda CRX Si (88-91): ”NA 55”

2024-01-01 FP Miata Alternate Head

#35253 from Don Tucker · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, Mazda MX-5 /Miata 1.8L (90-97), change weight as follows:
"2200 2150"
Mazda MX-5 /Miata (94-97)
"2035 2000
*2086 2050
**2137 2100"

2024-01-01 FP Triumph GT6 Adjustments

#35255 from Anthony Parker · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In EP spec line, Triumph GT6, make the following change in the Notes section:
"Two (2) 1.75” auto-type carburetors @ 1970 40 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990
lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive. Three (3) Weber 40mm DCOE w/28mm venturi on individual
runner manifold @ 2020 lb."

2024-01-01 FP Honda S2000 throttle body

#35272 from Aaron Johnson · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In EP spec line, Honda S2000, make the following changes to its spec line:
Fuel Injected Equipped Throttle Body Inside Diameter: "62 64"
Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .500”. An adaptor plate can be used to mount the 62mm throttle body
from '00-05 to the '06-09 intake manifold. The adaptor plate can be no more than 1.25" thick, and its bore must not exceed the
"Fuel Injected Equipped Throttle Body Inside Diameter" maximum spec of 64mm."

2024-01-01 FP Correction within Triumph TR8 Spec Line

#35315 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In EP spec line, Triumph TR8 (78-81), move the "Dry sump allowed" wording to the appropriate location as follows:
Carburetor. No. & Type: “Zenith Stromberg carbs or fuel injection. Dry sump is allowed.”
Notes: “Comp. Ratio limited to 12.0:1, Valve lift limited to .500”. Dry sump is allowed.”

2024-01-01 FP Correction to EP 924S/944 Spec Line

#35317 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In EP spec line, Porsche 944/924S 2.5L (2V) / 2.7L (2V) (83-89), change Weight as follows:

A specification table follows in the original; it is not shown here.

2024-01-01 P2 Replacement Engine Crankcase for 07/08 Suzuki GSX-R1000 Engines

#35340 from Michael A Reupert · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, add to notes as follows:
"No modifications allowed on engines manufactured after 2008 model year. 2007-2008 Suzuki GSX-R1000 crankcase part
#11300-21860 may be replaced with 2016-2019 Suzuki GSX-S1000 crankcase part #11301-04840."

2024-02-01 FP Update 1988-1991 Civic to Match 1988-1991 CRX

#35399 from Enrik Benazic · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

As printed in Fastrack

In HP, make the following weight change:
Honda Civic 1.5 (88-91)
“2245 2175
*2301 2229
**2357 2284”

2024-03-01 AS Request to Classify 1970-1981 Camaro and Firebird in AS

#33659 from Brandon Vivian · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, classify Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep as follows:
AS Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:

A specification table follows in the original; it is not shown here.

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2024-03-01 AS Fuel Cell 12

#34194 from Clark Cambern · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, add to Notes as follows:
Cadillac CTS-V (04-07): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken
from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24
inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with

2024-03-01 AS Please Classify the 6th Gen Into AS.

#35448 from Daniel Richardson · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, classify Chevrolet Camaro (16-) Full Prep as follows:
AS
Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:

A specification table follows in the original; it is not shown here.

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2024-03-01 FP GCR Correction - Redundant HP Spec Lines

#35623 from Production Committee · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In HP Spec Lines, delete the following redundant spec lines in their entirety:
Spec line #10 - VW Rabbit Cabriolet 1780
Spec line #3 - VW Scirocco 1588
Spec line #4 - VW Scirocco 1780 (8-valve) (83-88)
Spec line #5 - VW Scirocco 1588

2024-03-01 AS spec lines

#35713 from American Sedan Committee · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, classify Ford Mustang GT (05-14) with Restricted prep Engine as follows:
AS
Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-03-01 FP Update FP Protege (01-03) Model Info

#35715 from Production Committee · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, Mazda Protégé ES (01-03) change vehicle as follows:
"Mazda Protégé ES/5 (01-03)"

2024-04-01 AS Restricted Prep Aftermarket Parts Request

#35682 from Tom Aquilante · Rule change · TB 24-04 (2024-04 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."
In AS Spec Lines, Pontiac GTO (04-06), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2024-04-01 AS Allowance of 11

#35824 from American Sedan Committee · Rule change · TB 24-04 (2024-04 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Cadillac CTS-V (04-07), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Chevrolet Camaro SS (V8) (10-15), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Dodge Challenger (08-20), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Ford Mustang GT 5.0l (15-17), add to Notes the following:
"11" wide wheels can be used until 3/1/25."

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-05-01 AS 6th gen Camaro limited prep

#35733 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, classify Chevrolet Camaro 1LE (2016-) as follows:
AS Wheelbase Gear Ratios Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs.) Notes:
Chevrolet
Camaro, 1LE

A specification table follows in the original; it is not shown here.

2024-05-01 AS Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V8 LS1 Alum BLK

#35825 from Desi Colon · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, classify Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves
per cylinder, as follows:
AS Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

2024-05-01 P2 CN Spec ECU

#35835 from Bart Wolf · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line E, change the notes as follows:
"No engine modifications except for dry sump oil system, ECU mapping, and exhaust system the following: oil system, ECU, and
exhaust are unrestricted."

2024-05-01 FP Request to Replace CRX Plastic Panels

#35876 from Darryl Saylor · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In FP spec line "Honda CRX / CRX Si (84-87)", add the following wording to the Notes section:
"The plastic OE front header/nose body panel, lower rocker side-skirt, and lower door cap panel can be replaced by a
replica, which may be constructed of an alternate material, provided its appearance remains stock."

2024-05-01 AS Full Prep Head

#35891 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (82-92), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet Camaro (10-15), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86), add to Notes the following:
"Flo Tek Part # 203-500 are permitted."

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-05-01 FP FP data and parity

#35896 from Production Committee · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In the following FP spec lines, add the following wording to the Notes section:
Acura Integra (90-93)
Acura Integra LS (94-01)
Acura Integra GSR (92-93)
Honda Civic Del Sol VTEC (94-97)
Honda Civic Si (99-00)
"55mm Flat Plate Intake Restrictor is required."

2024-05-01 P2 E&O - Correct FIA Group CN spec line notes

#35900 from Club Racing Board · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, FIA Group CN spec line, change the notes as follows:
"FIA Group CN homologated chassis, brake calipers and discs, hub carriers, and suspension components are required. V de
V European Proto Endurance Series Challenge permitted bodywork, rear diffuser, wing, wheels, and assisted
shifting are allowed. Car M must comply with all other P2 requirements. Competitors must have copies of FIA Group CN
Technical Regulations and V de V European Proto Endurance Series Challenge Sporting and Technical Regulations in their
possession and present them upon request are available here: https://www.scca.com/pages/technical-forms-and-downloads."

2024-06-01 AS Request for Classification of 2018-2023 mustang In

#35764 from Michael Kamalian · Rule change · TB 24-06 (2024-06 Fastrack)

Summary

As printed in Fastrack

AS Spec Lines, classify Ford Mustang GT 5.0L (2018-) as follows:
AS Wheelbase Gear Ratios

A specification table follows in the original; it is not shown here.

2024-06-01 FP NIssan 300ZX Z31 to EP

#35830 from Murphy Nichols · Rule change · TB 24-06 (2024-06 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, classify Nissan 300ZX (84-89), as follows:

A specification table follows in the original; it is not shown here.

2024-06-01 FP RX7 1993 and Up Request In EP Spec Lines, classify

#36031 from Edward Zabinski · Rule change · TB 24-06 (2024-06 Fastrack)

Summary

As printed in Fastrack

Mazda RX-7 (92-97) as follows:

A specification table follows in the original; it is not shown here.

2024-06-01 FP Clean-up Multiple EP RX-8 Spec Lines In EP

#36156 from Production Committee · Rule change · TB 24-06 (2024-06 Fastrack)

Summary

As printed in Fastrack

Spec Lines, make the following changes to the two Mazda RX-8 spec lines.
Remove spec line entirely:
Mazda RX-8 (04-11)
Remove the wording "alternate":
Mazda RX-8 (04-11)(alternate)
Spec Mazda (SM/SMX) None.

2024-08-01 FP Errant entry in HP production line item

#36231 from Angus Crome · Rule change · TB 24-08 (2024-08 Fastrack)

Summary

As printed in Fastrack

In HP Spec Lines, change Track (F/R)mm/(in.) as follows:
Volkswagen Golf (GTI, GT, GL) (85-92): "2 1537/1529 (60.5/60.2)"
Volkswagen Jetta (GLI, GL) (85-92): "2 1537/1529 (60.5/60.2)"

2024-09-01 AS Mustang transmission ratios

#36662 from American Sedan Committee · Rule change · TB 24-09 (2024-09 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Notes as follows:
"Alternate transmission Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68.”
In AS Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows:
"Alternate transmission Ratios 3.24, 2.10, 1.42, 1.00, 0.81, .062."

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-10-01 FP Errors/emissions Honda Civic/CRX

#36700 from Martin Burk · Rule change · TB 24-10 (2024-10 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, Honda CRX / CRX Si (84-87), change Block Mat'l as follows:
"Iron Alum"

Applies to Honda CRX on this page: Chris Bovis

2024-11-01 FP 1275 HP Spridget Level 2 Only

#36518 from Darryl Saylor · Rule change · TB 24-09 (2024-09 Fastrack)

Summary

As printed in Fastrack

In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows:
"(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows:
"(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"

2024-12-01 P2 2000 cc Pinto Engine Car Weight

#37187 from Marvin Hodges · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Line E Note 2, add the following:
"8. Minimum weight 1335 lbs."

2025-01-01 AS Increase Coyote Engine Restrictor to 80mm

#36177 from Gregory Eaton · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, add to Notes as follows:
Ford mustang (GT 05-14): "Gen 1- 67mm Gen 2-64mm"
Ford mustang (GT 05-14): "Gen 1- 67mm"
Ford mustang (GT 15-17): "Gen 1- 67mm"
Ford mustang (GT 94-04): "Gen 1- 67mm Gen 2-64mm"
Ford mustang cobra & Cobra R Mercury Capri (79-93) (79-86): "Gen 1- 67mm Gen 2-64mm"

2025-01-01 AS Performance Pack for 2015+ Mustang

#36867 from Michael Kamalian · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang Coupe GT (05-14) Restricted Prep., change Notes as follows:
"The 4.6L engine assembly has a weight reduction of 300 lbs. 5.0L/6spd engine/trans: track pack front and rear spoiler allowed."
In AS Spec Lines, Ford Mustang Coupe GT (05-14) with Restricted Prep. engine, change Notes as follows:
"Max. Wheel Size: Dia.18.0 inches. Stock brakes or alternate Ford 14” Brembo Brake (Ford Racing Kit #M-2300-S) and full prep
brake package may be used. Either engine may be used. 1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l
Coyote 15-17 61mm FPR Cold Air Intake allowed Charge Motion Control Valves can be blocked off and removed for firewall
clearance Allow Cold Air Intake Tremec Magnum transmission may be used P/N- TUKT16901. Full Prep Transmissions rule
package may also be used. Max compression ratio, 11.2:1 track pack front and rear spoiler allowed. Alternate transmission

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2025-01-01 FP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line

#37119 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In EP SPEC LINES, BMW 325i/is (E30) (84-91), change Weight as follows:
"2200 2150
*2255 2204
**2310 2258"

2025-01-01 AS Gear Ratios

#37131 from Timothy White · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, change Gear Ratios as follows:
Cadillac CTS-V (04-07):
"2.97, 2.07, 1.43,1.00, 0.84,0.56 or 3.01, 2.07, 1.43, 1.0, .84, .57 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Full Prep:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Restricted Prep.:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet/Pontiac Camaro & Firebird (82-92) Full Prep:

2025-01-01 AS ECU specs for LS engine

#37208 from Gary Mathews · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In AS SPEC LINES, Cadillac CTS-V (04-07) Restricted Prep., change Notes as follows:
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Tremec TR6060
Transmission with 3.0 1, 2.07, 1.43, 1.0, .84, .57 ratios permitted. 11” wide wheels can be used until 3/1/25. Any ECM may be
used."
In AS SPEC LINES, Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep ., add to Notes as follows:
"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1, add to Notes as follows:

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2025-01-01 FP Fix Error in Spridget Spec Line

#37437 from Jason Stine · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In FP SPEC LINES, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change the following:
1275cc:
Bore x Stroke: "68.1x78.4 (2.68x3.09) 70.6x81.3 (2.78x3.20)"
Displacement: "(77.78) 1275"
Valves IN & EX: "(I) 32.1/(1.26) (E) 28.4/(1.12) (I) 33.3/(1.31) (E) 29.5/(1.16)"
1500cc:
Bore x Stroke: "1.1x84.3 73.7x87.4 (2.90x3.44)"
Displacement: "1491 (90.95) 1493"

2025-01-01 FP Create ruleset that allows GTL cars to run in FP

#37485 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

“(Effective January 1, 2026) (Effective January 1, 2025)." Any GT-Lite (GTL) car meeting all of the requirements of Appendix N
GT-LITE CATEGORY SPECIFICATIONS for inclusion into F PRODUCTION" may compete in the F-Production class. For GTL cars
competing in FP, the level of preparation and modifications will be determined by Appendix N and not by PCS 9.1.5.”

2025-02-21 FP Effective date for Jan 2025 GCR updates

#37654 from Doug Piner · Rule change · TB 25-02 (2025-02 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, add to Notes as follows:
BMW Z3 2.5LL "(Effective 2/21/2025) 52mm Flat Plate Intake Restrictor is required."
BMW Z3 2.8L (97-00): "(Effective 2/21/2025) 55mm Flat Plate Intake Restrictor is required."
BMW 328i/is E36 (96-99): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required."
BMW 328i/ci E46 (01-06): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required."
BMW 325i/is E46 (01-06): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."
BMW 325i/is E-36 (92-95): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."
BMW 325is M-Technic (1994): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."

2025-03-01 FP Request Competition Adjustment to BMW Z3 2.5L

#37120 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, change Notes as follows:
BMW Z3 2.5LL "(Effective 3/1/2025) 56mm 52mm Flat Plate Intake Restrictor is required."
BMW Z3 2.8L (97-00): "(Effective 3/1/2025) 59mm 55mm Flat Plate Intake Restrictor is required."
BMW 328i/is E36 (96-99): "(Effective 3/1/2025) 62mm 58mm Flat Plate Intake Restrictor is required."
BMW 328i/ci E46 (01-06): "(Effective 3/1/2025) 62mm 58mm Flat Plate Intake Restrictor is required."
BMW 325i/is E46 (01-06): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required."
BMW 325i/is E-36 (92-95): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required."
BMW 325is M-Technic (1994): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required."

2025-03-01 FP Interpretation of Production Rules on Mirrors

#37235 from Lawrence Slivinski · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In GCR, add new rule as Section 9.1.5.E.10.f:
"Any interior or exterior mirror(s) that meets rule 9.3.36 may be used."

2025-03-01 FP FP Class Adjustments

#37458 from Production Committee · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In FP SPEC LINES, change Notes as follows:
Acura Integra (90-93): "(Effective 3/1/2025) 55mm 51mm Flat Plate Intake Restrictor is required."
Acura Integra LS (94-01): "(Effective 3/1/2025) 55mm 51mm Flat Plate Intake Restrictor is required."
Acura Integra GSR (92-93): "(Effective 3/1/2025) 55mm 51mm Flat Plate Intake Restrictor is required."
Honda Civic Si (99-00): "(Effective 3/1/2025) 55mm 51mm Flat Plate Intake Restrictor is required.
In FP SPEC LINES, change as follows:
Honda Civic Del Sol VTEC (94-97): "
Weight: "(Effective 3/1/2025) 2265 *2322 **2378 2290 *2347 **2405

2025-03-01 FP Weight Reduction for Honda S2000

#37466 from Michael Unger · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In EP, Spec Lines make the following weight changes:

A specification table follows in the original; it is not shown here.

2025-03-01 FP Mazda 1999 Miata 1.8L

#37488 from Joe Carr · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, make the following weight change:
Mazda MX-5 /Miata (99-05):
"2150 2100
*2204 2153
**2258 2205"

2025-03-01 FP Errors & Omissions

#37648 from Bryan Floyd · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, Appendix N, GTL-FP Cars - Volkswagen, classify Jetta Mark - IV as follows:
GTL-FP Cars - VOLKSWAGEN
Model Years Body Style Drive-line Wheelbase (in) Notes
Jetta Mark - IV 4dr FWD 98.2

2025-03-01 FP GTL/FP consolidation 2025 Rules

#37659 from James Gregorius · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, Appendix N: L.9, Fuel Injection System, add the following:
"As an option, induction system “Chokes” may be used where a SIR is required. Said chokes shall be fitted to each barrel of
carburetor/throttle body and all airflow into engine must pass through them. Choke size will be the same as listed SIR unless
noted."

2025-03-01 AS Race memo

#37902 from American Sedan Committee · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, change Notes as follows:
Cadillac CTS-V (04-07) Restricted Prep. 6.0L V8 (Aluminum block, Aluminum heads), LS2, 2 valves/cylinder:
"Any ECM maybe used."
Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep. 6.2L V8 (Aluminum Block, Aluminum Heads), 2 valves per cylinder:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (82-92)s 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves per cylinder:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (93-02):

2025-04-01 AS Flotek Head Plunge Cut Inconsistencies

#37502 from Pamela Richardson · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.6., replace Figure 1 Value Seat Cutting Dimensions with the following:

2025-04-01 AS Notes clean up

#37693 from American Sedan Committee · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, change/add to Notes as follows:
Cadillac CTS-V (04-07):
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used. The
Drive Shaft Shop, Axle shaft part #'s 510220/510221 permitted."
Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #s: 14101081, 14014416 Port Volume (Max.): 081
casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb. weight reduction. Edelbrock Cylinder Head Part

2025-04-01 FP Request for Classification of Chevrolet Spark

#37755 from Kristian Smith · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

As printed in Fastrack

In HP Spec Lines, classify the Chevrolet Spark (16-22):

A specification table follows in the original; it is not shown here.

2025-04-01 FP Request to Lower Ford Festiva Minimum Weight to 1600 LBS

#37939 from Doug DeRonne · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

As printed in Fastrack

In HP Spec Lines "Ford Festiva (88-93)" change as follows:
Weight:
"1700 1600
*1743 1640
**1785 1680"
Notes:
"Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."

2025-04-01 FE2 Driver Safety & Comfort

#37965 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

As printed in Fastrack

In FE2, GCR section 9.1.1.G.2.E, add the following:
"g. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

2025-05-01 AS Errors and Omission

#38055 from American Sedan Committee · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT 5.0l (15-17), Flat Plate Restrictor Size, change as follows:
"67mm 64mm"

2025-05-01 AS Request to Add LS1/LS6 Intakes for 5.3L Truck Engine EnO

#38197 from Jim Clark · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.6.F., add the following to Intake Part #’s:
"17113697, 19418185, 89017230, 89017363, 89017364, and 89017365, 12561269 and 88894095"

2025-06-01 AS Errors and Omissions

#38234 from American Sedan Committee · Rule change · TB 25-06 (2025-06 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Gear Ratios the following:
"or 3.66, 2.43, 1.69, 1.32, 1.00, .65"

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2025-06-01 FP Base Weight Adjustment for H-Production X1/9 Spec Lines

#38255 from Matthew Brannon · Rule change · TB 25-06 (2025-06 Fastrack)

Summary

As printed in Fastrack

In HP Spec Lines, change Weight as follows:
Fiat X-1/9 & Bertone1500: “1790 1740 *1835 1784 **1880 1827”
Fiat X-1/9 1300: “1650 1600 *1691 1640 **1733 1680”
Fiat X-1/9 1300: “2060 2010”
Fiat X-1/9 1500: “1950 1900”

2025-07-01 AS RE: Previous Letter 37695 Update

#38245 from Michael Kamalian · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT 5.0 (2018-), change Weight as follows:
"3600 3525"

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton

2025-07-01 FP BMW Z4 update

#38490 from Bryce McGuire · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, BMW Z4 (03-05), add to Notes the following:
“52mm Flat Plate Intake Restrictor.”

2025-07-01 FP EP Fiat 124 Spider Competition Adjustment Request

#38498 from John Baucom · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, Fiat 124 Sport Spider 1600 & 124 Spider 2000, change as follows:
Weight: "2050 2000"
Carburetor No. & Type: "(2) Weber 40 IDF-40IFI, (2) Solex C40P116, 34 36mm choke(s) req’d, (2) Weber 45DCOE w/ 34 36 mm
choke(s) on I.R. manifold or fuel injection."

2025-10-01 FE2 FE & FE2 Bubble Tail

#38978 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

As printed in Fastrack

In FE, GCR section 9.1.1.G.2.F.k, change as follows:
"Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."

2025-10-01 FP HP Plymouth Arrow spec omission

#38995 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

As printed in Fastrack

In HP Spec Lines, Plymouth Arrow (76-80), add the following wording to Trans. Speeds(max):
"4 or 5"

2025-10-01 FP Add Wheel Diameter to Appendix G

#39008 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

As printed in Fastrack

In Appendix G.2.3, change as follows:
"Rim width and diameter are is absolute maximums."

2025-10-01 FP Add TB ID tolerance to general Prod rules

#39009 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.5.E., change as follows:
9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain
stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished."
9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must
remain stock (tolerance of +/-.25mm)."

2025-11-01 AS Cadillac CTS-V BOP Weight Change

#38640 from Alex Lozano · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Cadillac CTS-V (04-07) Restricted Prep., change Weight as follows:
"(Effective 11/1/2025) 3450 3400"

2025-11-01 FP Please Lower Weight of 280Z

#38871 from Matthew Miller · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, Nissan 280Z, change Weight (lbs) as follows:
"(Effective 11/1/2025) 2560 2400
*2624 2460
**2688 2520"

2025-11-01 FP Miata Weight Adjustment Follow Up

#38949 from Don Tucker · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, Mazda MX-5 / Miata 1.8L (90-97), Effective 11/1/2025 make the following weight change:
"2150 2125"

2025-11-01 FP Weight Break for 1098 Midget / Sprite

#38970 from Kendall Jones · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

As printed in Fastrack

In HP Spec Lines, Austin-Healey Sprite/Midget 1098cc, Effective 11/1/2025make the following weight change:
"1630 1550"

2025-11-01 FP HP Volvo 142 spec omission

#38994 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

As printed in Fastrack

In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes:
"Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."

2025-11-01 FP HP Mini DOHC 1.6

#38996 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

As printed in Fastrack

In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following
changes to the Notes:
"Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."

2025-11-01 FP 83-88 FP Scirocco Spec Line Creation

#38997 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, classify Volkswagen Scirocco (83-88) as follows:

A specification table follows in the original; it is not shown here.

2025-11-01 FP Add to Rabbit description

#39019 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, make the following spec line correction:
"Volkswagen Rabbit (Includes Convertible Cabriolet)"
In HP Spec Lines, make the following spec line correction:
"Volkswagen Rabbit 1588 (Includes Cabriolet)"
"Volkswagen Rabbit 1715 (Includes Cabriolet)"
"Volkswagen Rabbit 1780 (Includes Cabriolet)"

2025-11-01 FP Clean-up 9.1.5.E.7e

#39025 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.5.E.7., change as follows:
"e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes
Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear
disc brakes under this rule. When converting from rear drum brakes to rear disc brakes:
1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on
the vehicle’s spec line.
2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and
alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock

2025-11-01 FP Add TB size to Ford Mustang (94-98) Spec Line

#39130 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, Ford Mustang (94-98) add the following to the Fuel Injected Equipped Throttle Body Inside Diameter column:
"60"

2025-11-01 FP Correct Existing VW Scirocco Spec Line

#39140 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, Volkswagen Scirocco, change spec line as follows:

A specification table follows in the original; it is not shown here.

2025-12-01 AS 1994 Mustang Spec Line Request

#39104 from Barry Borgschatz, Jr · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT(94-04) with Restricted Prep Engine, add to notes the following:
"Ford Motorsport #M-6250-F303 camshaft is permitted."

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2025-12-01 FP TR2 Notes E&O

#39180 from Anthony Parker · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes:
"Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990
lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."

2025-12-01 FP Balance of Power

#39187 from Jim Simaras · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

As printed in Fastrack

In EP Spec Lines, make the following changes to Restrictors:
BMW Z3 2.5L: "52mm 50mm Flat Plate Intake Restrictor"
BMW Z3 2.8L (97-00): "55mm 53mm Flat Plate Intake Restrictor"
BMW 328i/is E36 (96-99): "58mm 55mm Flat Plate Intake Restrictor"
BMW 328i/ci E46 (01-06): "58mm 55mm Flat Plate Intake Restrictor"
BMW 325i/is (E46) (01-06): "56mm 53mm Flat Plate Intake Restrictor"
BMW 325is M-Technic (1994): "56mm 53mm Flat Plate Intake Restrictor"
BMW 325i/is E-36 (92-95): "56mm 53mm Flat Plate Intake Restrictor"

2025-12-01 FP Competition Adjustment Request

#39259 from David Strittmatter · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, Lancia Scorpion, change Weight as follows:
"2030 1950"

2025-12-01 FP Factory Roll Bar Removal on VW Convertible

#39268 from Tim Linerud · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

As printed in Fastrack

In FP Spec Line, Volkswagen Rabbit (Includes Convertible), remove the following wording in Notes:
"Factory roll bar must be removed on Cabriolet."

2025-12-01 FP FP Parity Request

#39325 from Mason Workman · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

As printed in Fastrack

In FP, change Weight as follows:
Acura Integra (90-93):
"2235 2285
*2291 2342
**2347 2399"
Acura Integra LS (94-01):
"2260 2310
*2317 2368

2025-12-01 FP Adjust former-GTL Honda's with B/D-Series Engines

#39374 from Production Committee · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

As printed in Fastrack

In GCR, Appendix N GTL inclusion into FP, Engines - HONDA, change Disp. (cc) – Weight (lbs) as follows:
"D15 – 1493cc – 1895 2000
D15b7 – 1493cc – 1895 2000
D16 – 1590cc – 1945 2055
D16A – 1590cc – 1945 2055
B16A – 1595cc – 1950 2065
B18 – 1797cc – 2050 2170
B18 – 1834cc – 2065 2185"

2026-01-01 AS Restrictor Plate Change for Gen 2 Ford Coyote Engine

#39501 from American Sedan Committee · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In AS Spec Lines, change Restrictor as follows:
Ford Mustang Incl. Cobra and Cobra R (79-93) and Mercury Capri (79-86) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang GT (94-04) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang Coupe GT (05-14) Restricted Prep 5.0L/6 speed 4 valves per cylinder: "64 mm 61 mm"
Ford Mustang GT (05-14) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang GT 5.0L (15-17) Restricted Preparation: "64 mm 61 mm"

2026-02-01 FP Request Toyota 5E Series Engines

#38208 from Scott Schick · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

As printed in Fastrack

In FP Appendix N, add spec line for the Toyota 5E engine to the "Engines - TOYOTA" section:

A specification table follows in the original; it is not shown here.

2026-02-01 FP Request for Toyota 4E Series Engines

#38209 from Scott Schick · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

As printed in Fastrack

In FP Appendix N, add spec line for the Toyota 4E engine to the "Engines - TOYOTA" section:

A specification table follows in the original; it is not shown here.

2026-02-01 AS Edelbrock manifold (& timing kit) to Chevy LS Spec Lines Request

#39055 from Jason Smith · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.6.D.2.h.2., add the following:
"(Effective 2/1/2026) i. Weight based on full preparation chassis choice spec line for GM LM7 5.3L
Carburetor Option:
Must use the full prep 4776 holly carburetor and spacer gasket
Edelbrock Performer RPM 71187 intake manifold
MSD 6014 ignition box
(Edelbrock part # kit 7118)"

2026-02-01 FP Dual Carbs for the Fiat X1/9

#39593 from Daniel Snow · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, change as follows:
Fiat X-1/9 & Bertone 1300:
"(1) Weber 32 DMTR or DATRA/100 w/32mm bores
(1) 40 DCNF w/32mm choke(s)
(2) auto-type side-draft w/28mm choke(s) on I.R. manifold
Orientation of the alternate carburetor is unrestricted. The alternate carb adapter may not be thicker than 1.25”. The adapter
may have a bore larger than the throttle bore of the approved alternate carburetor.
Valve Size: (I) 35.5/(1.40) (E) 31.3/(1.23)30.5/(1.20) (E) 1.23

2026-03-01 FP Correct Valve Sizes on FP Fiat x19 1300 and 1500

#39850 from DANIEL SNOW · Rule change · TB 26-03 (2026-03 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, change Drivetrain Notes as follows:
Fiat X-1/9 & Bertone 1300:
Valve Size: "(I) 35.5/(1.40) (E) 31.3/(1.23) (I) 36.3/(1.43) (E) 31.2/(1.23)"
Fiat X-1/9 & Bertone:
Valve Size: "(I) 35.5/(1.40) (E) 33.0/(1.30) (I) 36.3/(1.43) (E) 33.3/(1.31)"

2026-03-01 FP Dual Carburetor Adjustments

#39851 from DANIEL SNOW · Rule change · TB 26-03 (2026-03 Fastrack)

Summary

As printed in Fastrack

In FP Spec Lines, Fiat X-1/9 & Bertone, change Drivetrain Notes as follows:
"(2) auto-type side-draft w/28 30mm choke(s) on I.R. manifold"

2026-03-01 AS Re-Organization of AS Spec lines for 2026

#39887 from American Sedan Committee · Rule change · TB 26-03 (2026-03 Fastrack)

Summary

As printed in Fastrack

This AS Spec Lines re-organization simplifies the Spec Lines for all drivers. This version gives the chassis information on what
engines can be put in their cars. It removes information that is now repeated in the ruleset and adds engine/weight combos as
well as wheelbase/tire size information. The Notes in the Spec Lines have been reviewed to remove information now listed in
the engine build sheets and retain information pertinent to the chassis selected. Where there is nothing in the notes, it is not an
error. It just means everything a driver needs is now in the main rules or the build sheets.
In AS Spec Lines, delete current Spec Line in its entirety as follows:

A specification table follows in the original; it is not shown here.