AS + STL + EP at Buttonwillow Raceway Park

2023-04-01 EP Investigate Parity of Z3

#33343 from Tim Schreyer · Rule change · TB 23-01 (2023-01 Fastrack)

Effective 4/1/2023 In EP Spec Line BMW Z3 2.5L, change Notes as follows:
"58 56mm Flat Plate Intake Restrictor is required with both stock or alternate throttle body."

2023-06-01 EP 914-6 Valve Size Correction

#34185 from Kip VanSteenburg · Rule change · TB 23-06 (2023-05 Fastrack)

In EP Spec Lines, Porsche 914 - 6 2.0L, change Valves IN & EX mm/(in.) as follows:
"(I) 41.9 2.0/(1.65)
(E) 38.1 0/(1.50)"

2023-06-01 STL Clarify STL table B - IT spec notes on Tires

#34187 from Austin Hilliard · Rule change · TB 23-06 (2023-05 Fastrack)

In STL Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Notes as follows:
ITA-spec and ITS-spec RX7: "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires
must also conform to 9.1.4.2.Tires."
ITS, ITA, ITB, or ITC vehicles (1985- ): "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires &
Wheels. Tires must also conform to 9.1.4.2.Tires."

2023-07-01 EP Correct Intake Valve Size on 1500cc Midget/Spitfire

#34419 from Production Committee · Rule change · TB 23-06 (2023-05 Fastrack)

In FP Spec Lines, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change Intake Valve Size as follows:
"(I) 36.65.3/(1.44)"
In FP Spec Lines, Triumph Spitfire Mk. IV & 1500, change Intake Valve Size as follows:
"(I) 36.65.5/(1.440)"
In HP Spec Lines, Triumph Spitfire 1500, change Intake Valve Size as follows:
"(I) 36.65.5/(1.440)"
In HP Spec Lines, Triumph Spitfire Mk. III & IV 1500, change Intake Valve Size as follows:
"(I) 36.65.5/(1.440)"

2023-08-01 AS Crate Motor Part Numbers

#32944 from Sam Daniels · Rule change · TB 23-08 (2023-08 Fastrack)

In AS, GCR Section 9.1.6.F.2., change as follows:
"GM Performance parts CT400 P/N-1937 → 0604 or 1937 → 0604 engine assembly for GM produced vehicles."

2023-08-01 AS Request wheel size change

#33007 from Michael Kamalian · Rule change · TB 23-08 (2023-08 Fastrack)

In AS Spec Lines, Ford Mustang GT 5.0l (15-17) Restricted Preparation, change Notes as follows:
"Max. Wheel Size: Dia.18.0 19.0 inches."

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2023-08-01 AS Alternative Upper Front Control Arms for Dodge Challenger

#33352 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"SPC-66045 Alternate front upper control arms are permitted."

2023-08-01 AS Front Brake Caliper Adapters for Dodge Challenger

#33353 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"Stock brakes or alternate Dodge brakes (Part numbers: front caliper (0517 → 5106 (R) and 0517 → 5107 (L); rear caliper (R1542564 (R)
and R1542565 (L))) may be used with the brake rotor sizes listed in this specification line. Alternate brackets may be used to
facilitate updated/backdated components."

2023-09-01 EP Hub Note Clean Up In EP TR8 Spec Line

#34649 from Jeff young · Rule change · TB 23-09 (2023-09 Fastrack)

In the EP Spec Lines, Triumph TR8 (78-81), remove the following wording from Notes:
"Alternate front hubs are allowed provided they are of the same external dimensions as stock and weigh no less than the stock
hubs."

2023-09-01 EP Triumph GT6 Adjustments

#34662 from ANTHONY PARKER · Rule change · TB 23-09 (2023-09 Fastrack)

In EP Spec Lines, Triumph GT6, change Carburetor. No. & Type as follows:
"(2) 1.5” SU or Stromberg Auto-type carburetor(s)"

2023-09-01 EP Triumph GT6 Adjustments: Brakes

#34663 from ANTHONY PARKER · Rule change · TB 23-09 (2023-09 Fastrack)

In EP Spec Lines, Triumph GT6, add the following to Brakes Alt.: mm/(in.):
"(F) Calipers & discs from TR-6 (std. or alt)"

2023-12-01 EP Porsche 944/924S Rule Change Request

#35002 from Adam Achepohl · Rule change · TB 23-12 (2023-12 Fastrack)

In EP Spec Lines, delete the Porsche 944/924S 2.5L (2V) (83-88) spec line entirely, and create a new spec line for Porsche
944/924S 2.5L(2V) 2.7L(2V) (83-89) as follows:

A specification table follows in the original; it is not shown here.

2023-12-01 EP Triumph GT6 Adjustments

#35054 from ANTHONY PARKER · Rule change · TB 23-12 (2023-12 Fastrack)

In EP Spec Lines, Triumph GT6, change weight as follows:
"1830 1800"

2024-01-01 EP Request to Review Z3 2.5 Spec Line

#35073 from Tim Schreyer · Rule change · TB 24-01 (2024-01 Fastrack)

In EP spec line, BMW Z3 2.5L, change weight as follows:
"2450 2500
*2511 2563
**2573 2625"

2024-01-01 STL Alternate Carburetor Request for 79-85 RX7 12a

#35181 from Dan Sheppard · Rule change · TB 24-01 (2024-01 Fastrack)

In STL Table B: Alternate Vehicle and Engine Allowances, Mazda RX-7 12A (79-85), change Notes as follows:
"Street Porting of the engine only. Bridge porting, peripheral porting, and eyelash porting are prohibited. Contact SCCA National
Office for details of Street porting. Stock Nikki 4 bbl carburetor on a stock manifold only. or auto-type 2 bbl w/42mm choke(s) on
a “dual-y” manifold. Allow the standard removal of emissions related components, and allow air and fuel jets to be corrected.
Modification of the water jacket in the area of the spark plug for cooling purposes is permitted."

2024-01-01 EP Miata Alternate Head

#35253 from Don Tucker · Rule change · TB 24-01 (2024-01 Fastrack)

In EP Spec Lines, Mazda MX-5 /Miata 1.8L (90-97), change weight as follows:
"2200 2150"
Mazda MX-5 /Miata (94-97)
"2035 2000
*2086 2050
**2137 2100"

Applies to Mazda Miata on this page: Joe Carr, Glen McCready, Whitfield Gregg

2024-01-01 EP Triumph GT6 Adjustments

#35255 from Anthony Parker · Rule change · TB 24-01 (2024-01 Fastrack)

In EP spec line, Triumph GT6, make the following change in the Notes section:
"Two (2) 1.75” auto-type carburetors @ 1970 40 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990
lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive. Three (3) Weber 40mm DCOE w/28mm venturi on individual
runner manifold @ 2020 lb."

2024-01-01 EP Honda S2000 throttle body

#35272 from Aaron Johnson · Rule change · TB 24-01 (2024-01 Fastrack)

In EP spec line, Honda S2000, make the following changes to its spec line:
Fuel Injected Equipped Throttle Body Inside Diameter: "62 64"
Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .500”. An adaptor plate can be used to mount the 62mm throttle body
from '00-05 to the '06-09 intake manifold. The adaptor plate can be no more than 1.25" thick, and its bore must not exceed the
"Fuel Injected Equipped Throttle Body Inside Diameter" maximum spec of 64mm."

2024-01-01 EP Correction within Triumph TR8 Spec Line

#35315 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)

In EP spec line, Triumph TR8 (78-81), move the "Dry sump allowed" wording to the appropriate location as follows:
Carburetor. No. & Type: “Zenith Stromberg carbs or fuel injection. Dry sump is allowed.”
Notes: “Comp. Ratio limited to 12.0:1, Valve lift limited to .500”. Dry sump is allowed.”

2024-01-01 EP Correction to EP 924S/944 Spec Line

#35317 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)

In EP spec line, Porsche 944/924S 2.5L (2V) / 2.7L (2V) (83-89), change Weight as follows:

A specification table follows in the original; it is not shown here.

2024-02-01 STL ST Electric-Assisted Steering Systems

#35066 from Jose Osiris Pena · Rule change · TB 24-02 (2024-01 Fastrack)

In GCR, Section 9.1.4.M.16., change as follows:
"Power steering may be modified in any of the following ways:
a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be
modified internally to work without pump.
b. an OEM manual steering rack for that model may be fitted
c. an electric power steering pump may be fitted
d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used
e. an OEM hydraulic-assisted steering system may be used"

2024-02-01 STL BOP Adjustments

#35112 from Super Touring Committee · Rule change · TB 24-02 (2024-01 Fastrack)

In GCR, 9.1.4.H.1., change as follows:
"Minimum weights for cars with normally aspirated piston engines will be determined by 1.35 lbs/cc displacement for
the installed engine (see the following table). Displacement is the factory displacement for the installed engine. For the
purpose of weight assignment, engine displacement will be rounded to the nearest 50cc (e.g., 2176cc = 2200cc and
2175cc = 2150cc)."
In GCR, 9.1.4.H.1., change Minimum Weight on Chart as follows:
Factory Engine Displacement 1900: "Effective 3-1-24: 2565 2540"
Factory Engine Displacement 1950: "Effective 3-1-24: 2633 2583"

2024-02-01 STL Mazda 12A

#35320 from Super Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)

In STL Spec Lines, Table A, Mazda 12A, change Notes as follows:
"The 5th and 6th intake port actuators and valves may be removed or disabled."

2024-02-01 EP Update 1988-1991 Civic to Match 1988-1991 CRX

#35399 from Enrik Benazic · Rule change · TB 24-02 (2024-01 Fastrack)

In HP, make the following weight change:
Honda Civic 1.5 (88-91)
“2245 2175
*2301 2229
**2357 2284”

2024-03-01 AS Request to Classify 1970-1981 Camaro and Firebird in AS

#33659 from Brandon Vivian · Rule change · TB 24-03 (2024-03 Fastrack)

In AS Spec Lines, classify Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep as follows:
AS Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:

A specification table follows in the original; it is not shown here.

2024-03-01 AS Fuel Cell 12

#34194 from Clark Cambern · Rule change · TB 24-03 (2024-03 Fastrack)

In AS Spec Lines, add to Notes as follows:
Cadillac CTS-V (04-07): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken
from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24
inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with

2024-03-01 AS Please Classify the 6th Gen Into AS.

#35448 from Daniel Richardson · Rule change · TB 24-03 (2024-03 Fastrack)

In AS Spec Lines, classify Chevrolet Camaro (16-) Full Prep as follows:
AS
Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:

A specification table follows in the original; it is not shown here.

2024-03-01 EP GCR Correction - Redundant HP Spec Lines

#35623 from Production Committee · Rule change · TB 24-03 (2024-03 Fastrack)

In HP Spec Lines, delete the following redundant spec lines in their entirety:
Spec line #10 - VW Rabbit Cabriolet 1780
Spec line #3 - VW Scirocco 1588
Spec line #4 - VW Scirocco 1780 (8-valve) (83-88)
Spec line #5 - VW Scirocco 1588

2024-03-01 AS spec lines

#35713 from American Sedan Committee · Rule change · TB 24-03 (2024-03 Fastrack)

In AS Spec Lines, classify Ford Mustang GT (05-14) with Restricted prep Engine as follows:
AS
Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2024-04-01 AS Restricted Prep Aftermarket Parts Request

#35682 from Tom Aquilante · Rule change · TB 24-04 (2024-04 Fastrack)

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."
In AS Spec Lines, Pontiac GTO (04-06), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."

2024-04-01 AS Allowance of 11

#35824 from American Sedan Committee · Rule change · TB 24-04 (2024-04 Fastrack)

In AS Spec Lines, Cadillac CTS-V (04-07), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Chevrolet Camaro SS (V8) (10-15), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Dodge Challenger (08-20), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Ford Mustang GT 5.0l (15-17), add to Notes the following:
"11" wide wheels can be used until 3/1/25."

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2024-05-01 AS 6th gen Camaro limited prep

#35733 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)

In AS Spec Lines, classify Chevrolet Camaro 1LE (2016-) as follows:
AS Wheelbase Gear Ratios Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs.) Notes:
Chevrolet
Camaro, 1LE

A specification table follows in the original; it is not shown here.

2024-05-01 AS Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V8 LS1 Alum BLK

#35825 from Desi Colon · Rule change · TB 24-05 (2024-05 Fastrack)

In AS Spec Lines, classify Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves
per cylinder, as follows:
AS Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

2024-05-01 AS Full Prep Head

#35891 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (82-92), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet Camaro (10-15), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86), add to Notes the following:
"Flo Tek Part # 203-500 are permitted."

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2024-06-01 AS Request for Classification of 2018-2023 mustang In

#35764 from Michael Kamalian · Rule change · TB 24-06 (2024-06 Fastrack)

AS Spec Lines, classify Ford Mustang GT 5.0L (2018-) as follows:
AS Wheelbase Gear Ratios

A specification table follows in the original; it is not shown here.

2024-06-01 EP NIssan 300ZX Z31 to EP

#35830 from Murphy Nichols · Rule change · TB 24-06 (2024-06 Fastrack)

In EP Spec Lines, classify Nissan 300ZX (84-89), as follows:

A specification table follows in the original; it is not shown here.

2024-06-01 EP RX7 1993 and Up Request In EP Spec Lines, classify

#36031 from Edward Zabinski · Rule change · TB 24-06 (2024-06 Fastrack)

Mazda RX-7 (92-97) as follows:

A specification table follows in the original; it is not shown here.

2024-06-01 EP Clean-up Multiple EP RX-8 Spec Lines In EP

#36156 from Production Committee · Rule change · TB 24-06 (2024-06 Fastrack)

Spec Lines, make the following changes to the two Mazda RX-8 spec lines.
Remove spec line entirely:
Mazda RX-8 (04-11)
Remove the wording "alternate":
Mazda RX-8 (04-11)(alternate)
Spec Mazda (SM/SMX) None.

2024-08-01 EP Errant entry in HP production line item

#36231 from Angus Crome · Rule change · TB 24-08 (2024-08 Fastrack)

In HP Spec Lines, change Track (F/R)mm/(in.) as follows:
Volkswagen Golf (GTI, GT, GL) (85-92): "2 1537/1529 (60.5/60.2)"
Volkswagen Jetta (GLI, GL) (85-92): "2 1537/1529 (60.5/60.2)"

2024-09-01 AS Mustang transmission ratios

#36662 from American Sedan Committee · Rule change · TB 24-09 (2024-09 Fastrack)

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Notes as follows:
"Alternate transmission Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68.”
In AS Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows:
"Alternate transmission Ratios 3.24, 2.10, 1.42, 1.00, 0.81, .062."

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2024-11-01 EP 1275 HP Spridget Level 2 Only

#36518 from Darryl Saylor · Rule change · TB 24-09 (2024-09 Fastrack)

In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows:
"(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows:
"(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"

2024-11-01 EP NA Miata Track Width Correction

#36902 from Production Committee · Rule change · TB 24-11 (2024-11 Fastrack)

In EP Spec Lines, Track (F/R) mm/(in.), change as follows:
Mazda MX-5 /Miata 1.6L (-1993) - "1478/1491 (58.2/58.7) 1516/1534 (59.7/60.4)"
Mazda MX-5 /Miata 1.8L (90-97) - "1483/1509 (58.4/59.4) 1516/1534 (59.7/60.4)"
Mazda MX-5 /Miata (94-97) - "1483/1509 (58.4/59.4) 1516/1534 (59.7/60.4)"

2024-12-01 EP Triumph GT6 Adjustments

#37112 from Anthony Parker · Rule change · TB 24-12 (2024-12 Fastrack)

In EP Spec Lines, make the following changes in the "Triumph GT6" spec line:
Carburetor No. & Type: (2): "1.5” 1.75" Auto-type carburetor(s)"
Notes: "Two (2) 1.75” auto-type carburetors @ 1940 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990
lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive."

2024-12-01 STL Request to Remove Miata Hubs from General category

#37138 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)

In GCR, Section 9.1.4.M.18., change as follows:
"18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda
Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."

2025-01-01 AS Increase Coyote Engine Restrictor to 80mm

#36177 from Gregory Eaton · Rule change · TB 25-01 (2025-01 Fastrack)

In AS Spec Lines, add to Notes as follows:
Ford mustang (GT 05-14): "Gen 1- 67mm Gen 2-64mm"
Ford mustang (GT 05-14): "Gen 1- 67mm"
Ford mustang (GT 15-17): "Gen 1- 67mm"
Ford mustang (GT 94-04): "Gen 1- 67mm Gen 2-64mm"
Ford mustang cobra & Cobra R Mercury Capri (79-93) (79-86): "Gen 1- 67mm Gen 2-64mm"

2025-01-01 AS Performance Pack for 2015+ Mustang

#36867 from Michael Kamalian · Rule change · TB 25-01 (2025-01 Fastrack)

In AS Spec Lines, Ford Mustang Coupe GT (05-14) Restricted Prep., change Notes as follows:
"The 4.6L engine assembly has a weight reduction of 300 lbs. 5.0L/6spd engine/trans: track pack front and rear spoiler allowed."
In AS Spec Lines, Ford Mustang Coupe GT (05-14) with Restricted Prep. engine, change Notes as follows:
"Max. Wheel Size: Dia.18.0 inches. Stock brakes or alternate Ford 14” Brembo Brake (Ford Racing Kit #M-2300-S) and full prep
brake package may be used. Either engine may be used. 1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l
Coyote 15-17 61mm FPR Cold Air Intake allowed Charge Motion Control Valves can be blocked off and removed for firewall
clearance Allow Cold Air Intake Tremec Magnum transmission may be used P/N- TUKT16901. Full Prep Transmissions rule
package may also be used. Max compression ratio, 11.2:1 track pack front and rear spoiler allowed. Alternate transmission

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2025-01-01 EP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line

#37119 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)

In EP SPEC LINES, BMW 325i/is (E30) (84-91), change Weight as follows:
"2200 2150
*2255 2204
**2310 2258"

2025-01-01 AS Gear Ratios

#37131 from Timothy White · Rule change · TB 25-01 (2025-01 Fastrack)

In AS Spec Lines, change Gear Ratios as follows:
Cadillac CTS-V (04-07):
"2.97, 2.07, 1.43,1.00, 0.84,0.56 or 3.01, 2.07, 1.43, 1.0, .84, .57 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Full Prep:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Restricted Prep.:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet/Pontiac Camaro & Firebird (82-92) Full Prep:

2025-01-01 AS ECU specs for LS engine

#37208 from Gary Mathews · Rule change · TB 25-01 (2025-01 Fastrack)

In AS SPEC LINES, Cadillac CTS-V (04-07) Restricted Prep., change Notes as follows:
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Tremec TR6060
Transmission with 3.0 1, 2.07, 1.43, 1.0, .84, .57 ratios permitted. 11” wide wheels can be used until 3/1/25. Any ECM may be
used."
In AS SPEC LINES, Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep ., add to Notes as follows:
"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1, add to Notes as follows:

2025-02-21 EP Effective date for Jan 2025 GCR updates

#37654 from Doug Piner · Rule change · TB 25-02 (2025-02 Fastrack)

In EP Spec Lines, add to Notes as follows:
BMW Z3 2.5LL "(Effective 2/21/2025) 52mm Flat Plate Intake Restrictor is required."
BMW Z3 2.8L (97-00): "(Effective 2/21/2025) 55mm Flat Plate Intake Restrictor is required."
BMW 328i/is E36 (96-99): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required."
BMW 328i/ci E46 (01-06): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required."
BMW 325i/is E46 (01-06): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."
BMW 325i/is E-36 (92-95): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."
BMW 325is M-Technic (1994): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."

2025-03-01 EP Request Competition Adjustment to BMW Z3 2.5L

#37120 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)

In EP Spec Lines, change Notes as follows:
BMW Z3 2.5LL "(Effective 3/1/2025) 56mm 52mm Flat Plate Intake Restrictor is required."
BMW Z3 2.8L (97-00): "(Effective 3/1/2025) 59mm 55mm Flat Plate Intake Restrictor is required."
BMW 328i/is E36 (96-99): "(Effective 3/1/2025) 62mm 58mm Flat Plate Intake Restrictor is required."
BMW 328i/ci E46 (01-06): "(Effective 3/1/2025) 62mm 58mm Flat Plate Intake Restrictor is required."
BMW 325i/is E46 (01-06): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required."
BMW 325i/is E-36 (92-95): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required."
BMW 325is M-Technic (1994): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required."

2025-03-01 EP Interpretation of Production Rules on Mirrors

#37235 from Lawrence Slivinski · Rule change · TB 25-03 (2025-03 Fastrack)

In GCR, add new rule as Section 9.1.5.E.10.f:
"Any interior or exterior mirror(s) that meets rule 9.3.36 may be used."

2025-03-01 EP Weight Reduction for Honda S2000

#37466 from Michael Unger · Rule change · TB 25-03 (2025-03 Fastrack)

In EP, Spec Lines make the following weight changes:

A specification table follows in the original; it is not shown here.

2025-03-01 EP Mazda 1999 Miata 1.8L

#37488 from Joe Carr · Rule change · TB 25-03 (2025-03 Fastrack)

In EP Spec Lines, make the following weight change:
Mazda MX-5 /Miata (99-05):
"2150 2100
*2204 2153
**2258 2205"

2025-03-01 AS Race memo

#37902 from American Sedan Committee · Rule change · TB 25-03 (2025-03 Fastrack)

In AS Spec Lines, change Notes as follows:
Cadillac CTS-V (04-07) Restricted Prep. 6.0L V8 (Aluminum block, Aluminum heads), LS2, 2 valves/cylinder:
"Any ECM maybe used."
Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep. 6.2L V8 (Aluminum Block, Aluminum Heads), 2 valves per cylinder:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (82-92)s 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves per cylinder:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (93-02):

2025-04-01 AS Flotek Head Plunge Cut Inconsistencies

#37502 from Pamela Richardson · Rule change · TB 25-04 (2025-04 Fastrack)

In GCR, Section 9.1.6., replace Figure 1 Value Seat Cutting Dimensions with the following:

2025-04-01 AS Notes clean up

#37693 from American Sedan Committee · Rule change · TB 25-04 (2025-04 Fastrack)

In AS Spec Lines, change/add to Notes as follows:
Cadillac CTS-V (04-07):
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used. The
Drive Shaft Shop, Axle shaft part #'s 510220/510221 permitted."
Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #s: 14101081, 14014416 Port Volume (Max.): 081
casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb. weight reduction. Edelbrock Cylinder Head Part

2025-04-01 EP Request for Classification of Chevrolet Spark

#37755 from Kristian Smith · Rule change · TB 25-04 (2025-04 Fastrack)

In HP Spec Lines, classify the Chevrolet Spark (16-22):

A specification table follows in the original; it is not shown here.

2025-04-01 EP Request to Lower Ford Festiva Minimum Weight to 1600 LBS

#37939 from Doug DeRonne · Rule change · TB 25-04 (2025-04 Fastrack)

In HP Spec Lines "Ford Festiva (88-93)" change as follows:
Weight:
"1700 1600
*1743 1640
**1785 1680"
Notes:
"Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."

2025-05-01 STL E&O: SMX Allowance in STL

#37945 from Greg Amy · Rule change · TB 25-05 (2025-05 Fastrack)

In STL Spec Lines, Table B, Mazda Spec MX5 Challenge, change as follows:
Minimum Weight: "2500 See 9.1.7.1."
Notes: "Mazda MX5 Challenge car must utilize the following components: Roush CNC cylinder head 0000-01-5300,Mahle
standard or +0.005 0000-01-5310, OEM camshaft, 11:1 compression ratio, header 0000-06-5407-NC, exhaust 0000-06-5427-NC,
cold air intake 0000- 06-5150-KT, ECU flash 0000-01-5379, Pagid front brake pads 0000-03-5104-SP or endurance pads 0000-03-
5104-EN, Pagid rear brake pads 0000-03-5114-SP or endurance pads 0000-03-5114-EN, Penske front shock 0000-04-5291-SA,
Penske rear shock 0000-04-5292-SA, Penske rear mount kit 0000-04-5358, Front mount kit 0000-04-5359, Front offset bushing
0000-04-5407-NC, Eibach front springs 0000-04-9700-08, Eibach rear springs 0000-04-9400-07, Eibach helper springs 0000-04-

Applies to Mazda Miata on this page: Jared Korth, Ricardo Arruda, Gavin Wardle, Ryan Gutile, Bryce Johnson, Andy Chittum, Adrian Comstock

2025-05-01 AS Errors and Omission

#38055 from American Sedan Committee · Rule change · TB 25-05 (2025-05 Fastrack)

In AS Spec Lines, Ford Mustang GT 5.0l (15-17), Flat Plate Restrictor Size, change as follows:
"67mm 64mm"

2025-05-01 AS Request to Add LS1/LS6 Intakes for 5.3L Truck Engine EnO

#38197 from Jim Clark · Rule change · TB 25-05 (2025-05 Fastrack)

In GCR, Section 9.1.6.F., add the following to Intake Part #’s:
"17113697, 19418185, 89017230, 89017363, 89017364, and 89017365, 12561269 and 88894095"

2025-06-01 AS Errors and Omissions

#38234 from American Sedan Committee · Rule change · TB 25-06 (2025-06 Fastrack)

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Gear Ratios the following:
"or 3.66, 2.43, 1.69, 1.32, 1.00, .65"

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2025-06-01 EP Base Weight Adjustment for H-Production X1/9 Spec Lines

#38255 from Matthew Brannon · Rule change · TB 25-06 (2025-06 Fastrack)

In HP Spec Lines, change Weight as follows:
Fiat X-1/9 & Bertone1500: “1790 1740 *1835 1784 **1880 1827”
Fiat X-1/9 1300: “1650 1600 *1691 1640 **1733 1680”
Fiat X-1/9 1300: “2060 2010”
Fiat X-1/9 1500: “1950 1900”

2025-07-01 AS RE: Previous Letter 37695 Update

#38245 from Michael Kamalian · Rule change · TB 25-07 (2025-07 Fastrack)

In AS Spec Lines, Ford Mustang GT 5.0 (2018-), change Weight as follows:
"3600 3525"

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe

2025-07-01 EP BMW Z4 update

#38490 from Bryce McGuire · Rule change · TB 25-07 (2025-07 Fastrack)

In EP Spec Lines, BMW Z4 (03-05), add to Notes the following:
“52mm Flat Plate Intake Restrictor.”

2025-07-01 EP EP Fiat 124 Spider Competition Adjustment Request

#38498 from John Baucom · Rule change · TB 25-07 (2025-07 Fastrack)

In EP Spec Lines, Fiat 124 Sport Spider 1600 & 124 Spider 2000, change as follows:
Weight: "2050 2000"
Carburetor No. & Type: "(2) Weber 40 IDF-40IFI, (2) Solex C40P116, 34 36mm choke(s) req’d, (2) Weber 45DCOE w/ 34 36 mm
choke(s) on I.R. manifold or fuel injection."

2025-08-01 STL Lotus Weight Reduction

#38772 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)

In 9.1.2. GT2/ST Spec Lines, Lotus Evora GT4, change Weight as follows:
"2750 2700"
In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows:
Lotus Elise Cup R: "2300 2250"
Lotus Elise SC/ Lotus Exige SC: "2300 2550
2500 2450"

2025-10-01 EP HP Plymouth Arrow spec omission

#38995 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

In HP Spec Lines, Plymouth Arrow (76-80), add the following wording to Trans. Speeds(max):
"4 or 5"

2025-10-01 EP Add Wheel Diameter to Appendix G

#39008 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

In Appendix G.2.3, change as follows:
"Rim width and diameter are is absolute maximums."

2025-10-01 EP Add TB ID tolerance to general Prod rules

#39009 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

In GCR, Section 9.1.5.E., change as follows:
9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain
stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished."
9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must
remain stock (tolerance of +/-.25mm)."

2025-11-01 AS Cadillac CTS-V BOP Weight Change

#38640 from Alex Lozano · Rule change · TB 25-09 (2025-09 Fastrack)

In AS Spec Lines, Cadillac CTS-V (04-07) Restricted Prep., change Weight as follows:
"(Effective 11/1/2025) 3450 3400"

2025-11-01 EP Please Lower Weight of 280Z

#38871 from Matthew Miller · Rule change · TB 25-09 (2025-09 Fastrack)

In EP Spec Lines, Nissan 280Z, change Weight (lbs) as follows:
"(Effective 11/1/2025) 2560 2400
*2624 2460
**2688 2520"

2025-11-01 EP Miata Weight Adjustment Follow Up

#38949 from Don Tucker · Rule change · TB 25-10 (2025-10 Fastrack)

In EP Spec Lines, Mazda MX-5 / Miata 1.8L (90-97), Effective 11/1/2025 make the following weight change:
"2150 2125"

2025-11-01 EP Weight Break for 1098 Midget / Sprite

#38970 from Kendall Jones · Rule change · TB 25-10 (2025-10 Fastrack)

In HP Spec Lines, Austin-Healey Sprite/Midget 1098cc, Effective 11/1/2025make the following weight change:
"1630 1550"

2025-11-01 EP HP Volvo 142 spec omission

#38994 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes:
"Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."

2025-11-01 EP HP Mini DOHC 1.6

#38996 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following
changes to the Notes:
"Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."

2025-11-01 EP Add to Rabbit description

#39019 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

In FP Spec Lines, make the following spec line correction:
"Volkswagen Rabbit (Includes Convertible Cabriolet)"
In HP Spec Lines, make the following spec line correction:
"Volkswagen Rabbit 1588 (Includes Cabriolet)"
"Volkswagen Rabbit 1715 (Includes Cabriolet)"
"Volkswagen Rabbit 1780 (Includes Cabriolet)"

2025-11-01 EP Clean-up 9.1.5.E.7e

#39025 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

In GCR, Section 9.1.5.E.7., change as follows:
"e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes
Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear
disc brakes under this rule. When converting from rear drum brakes to rear disc brakes:
1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on
the vehicle’s spec line.
2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and
alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock

2025-11-01 EP Add TB size to Ford Mustang (94-98) Spec Line

#39130 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

In EP Spec Lines, Ford Mustang (94-98) add the following to the Fuel Injected Equipped Throttle Body Inside Diameter column:
"60"

2025-12-01 AS 1994 Mustang Spec Line Request

#39104 from Barry Borgschatz, Jr · Rule change · TB 25-12 (2025-12 Fastrack)

In AS Spec Lines, Ford Mustang GT(94-04) with Restricted Prep Engine, add to notes the following:
"Ford Motorsport #M-6250-F303 camshaft is permitted."

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2025-12-01 EP TR2 Notes E&O

#39180 from Anthony Parker · Rule change · TB 25-12 (2025-12 Fastrack)

In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes:
"Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990
lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."

2025-12-01 EP Balance of Power

#39187 from Jim Simaras · Rule change · TB 25-12 (2025-12 Fastrack)

In EP Spec Lines, make the following changes to Restrictors:
BMW Z3 2.5L: "52mm 50mm Flat Plate Intake Restrictor"
BMW Z3 2.8L (97-00): "55mm 53mm Flat Plate Intake Restrictor"
BMW 328i/is E36 (96-99): "58mm 55mm Flat Plate Intake Restrictor"
BMW 328i/ci E46 (01-06): "58mm 55mm Flat Plate Intake Restrictor"
BMW 325i/is (E46) (01-06): "56mm 53mm Flat Plate Intake Restrictor"
BMW 325is M-Technic (1994): "56mm 53mm Flat Plate Intake Restrictor"
BMW 325i/is E-36 (92-95): "56mm 53mm Flat Plate Intake Restrictor"

2026-01-01 EP Request to Update E30 BMW Throttle Body Diameter Verbiage

#39363 from Tim Schreyer · Rule change · TB 26-01 (2026-01 Fastrack)

In EP Spec Line BMW 325i/is E30 (84-91), change Drivetrain Notes as follows:
"Fuel Injection, TB: 60mm"

2026-01-01 AS Restrictor Plate Change for Gen 2 Ford Coyote Engine

#39501 from American Sedan Committee · Rule change · TB 26-01 (2026-01 Fastrack)

In AS Spec Lines, change Restrictor as follows:
Ford Mustang Incl. Cobra and Cobra R (79-93) and Mercury Capri (79-86) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang GT (94-04) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang Coupe GT (05-14) Restricted Prep 5.0L/6 speed 4 valves per cylinder: "64 mm 61 mm"
Ford Mustang GT (05-14) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang GT 5.0L (15-17) Restricted Preparation: "64 mm 61 mm"

2026-01-01 STL Weight adjustment for STL

#39579 from Super Touring Committee · Rule change · TB 26-01 (2026-01 Fastrack)

In GCR, Section 9.1.4.2.H.1. change Minimum Weight on chart as follows:

A specification table follows in the original; it is not shown here.

2026-02-01 AS Edelbrock manifold (& timing kit) to Chevy LS Spec Lines Request

#39055 from Jason Smith · Rule change · TB 26-01 (2026-01 Fastrack)

In GCR, Section 9.1.6.D.2.h.2., add the following:
"(Effective 2/1/2026) i. Weight based on full preparation chassis choice spec line for GM LM7 5.3L
Carburetor Option:
Must use the full prep 4776 holly carburetor and spacer gasket
Edelbrock Performer RPM 71187 intake manifold
MSD 6014 ignition box
(Edelbrock part # kit 7118)"