BoP Lab / Buttonwillow Raceway Park

FP + GT2 at Buttonwillow Raceway Park

No mapCal Club 2024

This track has been raced on 2 configurations (The Circuit, 2.57 mi; 2.92 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.

Pos	Car	Driver	Class	#	Lap	Theoretical	Qual	Race	5-lap stint	Consistency	Trap	S1	S2	S3
1	Chevrolet Camaro	Tim Carroll	GT2	46	1:42.698 A-Q1	1:42.698	1:42.698 A-Q1	1:44.128 A-R1	1:44.791 A-R1	+2.721 A-R1	149.0 A-P	28.597 A-Q1	29.839 A-Q1	44.262 A-Q1
2	Chevrolet Camaro	Jean Meynet	GT2	28	1:44.227 A-Q1	1:44.227	1:44.227 A-Q1	1:46.043 A-R1	1:46.393 A-R1	+1.382 A-R1	149.2 A-Q1	28.543 A-Q1	30.683 A-Q1	45.001 A-Q1
3	Ford Mustang	Brad McAllister	GT2	29	1:45.818 B-Q2	1:45.409	1:45.818 B-Q2	1:46.926 B-R1	1:47.740 B-R1	+1.198 B-R1	115.9 B-Q2	28.729 B-Q2	30.833 B-R1	45.847 B-Q2
4	Dodge Challenger	Ben Valentine	GT2	124, 24	1:46.922 A-Q1	1:46.608	1:46.922 A-Q1	1:47.171 B-R1	1:47.975 B-R1	+0.946 B-R1	132.9 A-P	29.689 B-Q1	30.929 A-Q1	45.990 B-Q2
5	Chevrolet Camaro	Sean Berardi	GT2	9	1:47.904 A-R2	1:47.266	1:50.095 A-Q2	1:47.904 A-R2	1:48.562 A-R2	+1.288 A-R2	133.2 A-R2	29.806 A-R2	31.073 A-R2	46.387 A-R2
6	Porsche GT3	Rocky Crocker	GT2	61	1:47.914 A-Q1	1:47.312	1:47.914 A-Q1	1:48.433 A-R1	1:50.149 A-R1	+3.225 A-R1	155.7 A-Q1	29.826 A-Q1	31.456 A-Q1	46.030 A-Q1
7	Chevrolet Corvette	Igor Lyustin	GT2	71	1:49.904 A-R2	1:49.689	1:50.345 A-Q1	1:49.904 A-R2	1:50.694 A-R2	+3.172 A-R2	145.8 A-Q1	30.271 A-R2	31.850 A-R2	47.568 A-R2
8	Mazda RX-7	Guy Laidig	GT2	52	1:51.013 A-Q2	1:50.266	1:51.013 A-Q2	1:52.486 A-R2	1:53.354 A-R2	+1.740 A-R2	138.7 A-Q1	30.134 A-P	32.225 A-P	47.907 A-Q1
9	Mazda RX-7	Michael Lewis	FP	32	1:55.440 B-R2	1:55.401	1:56.121 B-Q1	1:55.440 B-R2	1:56.358 B-R2	+2.235 B-R2	128.8 A-R2	31.255 B-R2	33.299 B-Q2	50.847 B-R2
10	Nissan Sentra SE-R	Brian Linn	FP	123, 3	1:55.722 B-R2	1:55.294	1:57.239 B-Q1	1:55.722 B-R2	1:56.460 B-R2	+1.971 B-R2	128.3 B-P	31.416 B-R2	33.400 B-R2	50.478 B-R2
11	Volkswagen GTI	Tim Linerud	FP	95	1:56.016 B-P	1:56.016		2:06.156 B-R1	2:07.807 B-R1	+3.270 B-R1	93.4 B-R2	33.738 B-R1	35.656 B-P	55.246 B-P
12	Mazda MIata	Steven Powers	FP	145	1:56.276 B-R2	1:55.982	1:57.032 B-Q1	1:56.276 B-R2	1:56.620 B-R2	+0.759 B-R2	134.3 A-Q2, A-R2	31.570 B-R2	33.696 B-R2	50.716 B-R2
13	Mazda RX-7	Scott Graham	GT2	91	1:56.607 B-R2	1:55.014	2:00.008 B-Q1	1:56.607 B-R2	1:57.173 B-R2	+2.205 B-R2	100.8 B-R2	30.931 B-R2	33.562 B-R2	50.521 B-R2
14	Porsche GT3 Cup	Robert Kelley 2+ cars	GT2	98	1:57.745 A-Q2	1:57.440	1:57.745 A-Q2	1:58.760 A-R1	1:59.706 A-R1	+1.876 A-R1	125.1 A-R1	32.864 A-R1	33.998 A-Q2	50.578 A-Q2
15	Dodge VIPER	Robert Kelley 2+ cars	GT2	88	1:57.753 B-P	1:57.501	2:00.453 B-Q2	1:59.538 B-R2	2:02.474 B-R2	+3.373 B-R2	92.9 B-Q1	31.983 B-P	33.965 B-P	51.553 B-P
16	Fiat X/1 9	Daniel Snow	FP	1	1:59.128 B-R2	1:58.152	2:00.398 B-Q1	1:59.128 B-R2	1:59.511 B-R2	+0.364 B-R2	137.8 A-R2	31.878 B-R2	34.053 B-R2	52.221 A-R2
17	Mazda RX-7	Wayne Graham >115%	GT2	96	2:00.512 B-R1	1:59.533	2:01.239 B-Q1	2:00.512 B-R1	2:01.174 B-R1	+1.175 B-R1	100.1 B-R1	32.073 B-R1	34.881 B-R1	52.579 B-R1
18	Porsche 914-4	Garey Raymond >115%	FP	29	2:15.932 B-R2	2:15.932	2:21.274 B-Q1	2:15.932 B-R2	2:17.314 B-R2	+3.922 B-R2	84.8 B-R1	37.237 B-R2	39.091 B-R2	59.604 B-R2

One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it. Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.

Sectors

S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi

Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.

By car

Car	Class	Drivers	Lap	Qual	Race	Trap	S1	S2	S3
Chevrolet Camaro	GT2	3	1:42.698Tim Carroll	1:42.698Tim Carroll	1:44.128Tim Carroll	149.2Jean Meynet	28.543Jean Meynet	29.839Tim Carroll	44.262Tim Carroll
Ford Mustang	GT2	1	1:45.818Brad McAllister	1:45.818Brad McAllister	1:46.926Brad McAllister	115.9Brad McAllister	28.729Brad McAllister	30.833Brad McAllister	45.847Brad McAllister
Dodge Challenger	GT2	1	1:46.922Ben Valentine	1:46.922Ben Valentine	1:47.171Ben Valentine	132.9Ben Valentine	29.689Ben Valentine	30.929Ben Valentine	45.990Ben Valentine
Porsche GT3	GT2	2	1:47.914Rocky Crocker	1:47.914Rocky Crocker	1:48.433Rocky Crocker	155.7Rocky Crocker	29.826Rocky Crocker	31.456Rocky Crocker	46.030Rocky Crocker
Porsche GT3	GT2	1	1:47.914Rocky Crocker	1:47.914Rocky Crocker	1:48.433Rocky Crocker	155.7Rocky Crocker	29.826Rocky Crocker	31.456Rocky Crocker	46.030Rocky Crocker
Porsche GT3 Cup	GT2	1	1:57.745Robert Kelley	1:57.745Robert Kelley	1:58.760Robert Kelley	125.1Robert Kelley	32.864Robert Kelley	33.998Robert Kelley	50.578Robert Kelley
Chevrolet Corvette	GT2	1	1:49.904Igor Lyustin	1:50.345Igor Lyustin	1:49.904Igor Lyustin	145.8Igor Lyustin	30.271Igor Lyustin	31.850Igor Lyustin	47.568Igor Lyustin
Mazda RX-7	FP/GT2	4	1:51.013Guy Laidig	1:51.013Guy Laidig	1:52.486Guy Laidig	138.7Guy Laidig	30.134Guy Laidig	32.225Guy Laidig	47.907Guy Laidig
Nissan Sentra SE-R	FP	1	1:55.722Brian Linn	1:57.239Brian Linn	1:55.722Brian Linn	128.3Brian Linn	31.416Brian Linn	33.400Brian Linn	50.478Brian Linn
Volkswagen GTI	FP	1	1:56.016Tim Linerud		2:06.156Tim Linerud	93.4Tim Linerud	33.738Tim Linerud	35.656Tim Linerud	55.246Tim Linerud
Mazda MIata	FP	1	1:56.276Steven Powers	1:57.032Steven Powers	1:56.276Steven Powers	134.3Steven Powers	31.570Steven Powers	33.696Steven Powers	50.716Steven Powers
Dodge VIPER	GT2	1	1:57.753Robert Kelley	2:00.453Robert Kelley	1:59.538Robert Kelley	92.9Robert Kelley	31.983Robert Kelley	33.965Robert Kelley	51.553Robert Kelley
Fiat X 1/9	FP	1	1:59.128Daniel Snow	2:00.398Daniel Snow	1:59.128Daniel Snow	137.8Daniel Snow	31.878Daniel Snow	34.053Daniel Snow	52.221Daniel Snow
Porsche 914-4	FP	1	2:15.932Garey Raymond	2:21.274Garey Raymond	2:15.932Garey Raymond	84.8Garey Raymond	37.237Garey Raymond	39.091Garey Raymond	59.604Garey Raymond

The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.

Rule changes between these events

Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22

2024-03-01 GT2 Classify Corvette C8 (2020- ) into GT2/ST

#33759 from Andrew Aquilante · Rule change · TB 24-03 (2024-03 Fastrack)

neutralChevrolet Corvette C8 (2020–) classified into GT2-ST with 6162cc displacement, 3300 lbs minimum weight, 71mm restrictor.

In GT2 Spec Lines, classify Chevrolet Corvette C8 (20-) as follows:
GT2-ST Maximum Displacement Minimum Weight Restrictor Notes
Chevrolet Corvette C8
(20-)
6162 3300 71mm -
Flat Plate
LT2 engine.

Applies to Chevrolet Corvette on this page: Igor Lyustin

2024-03-01 GT2 Requesting classification for a 2015 Mitjet ST in GT2

#35408 from Jim Froula · Rule change · TB 24-03 (2024-03 Fastrack)

neutral2015 Mitjet ST added to GT2, must run per VTS specifications with complete FIA form CdM008.

In GT2 Spec Lines, GT Cars - MITJET ST, classify MITJET ST as follows:
GT Cars – MITJET ST
Model Years Body Style Drive-
line
Wheel-
base (in)
Notes
MITJET ST 2015 RWD 94.5 Must run per VTS specifications. Must have

Show 2 more lines

complete car Specifications (FIA form
CdM008) at every entered race event.

2024-03-01 FP GCR Correction - Redundant HP Spec Lines

#35623 from Production Committee · Rule change · TB 24-03 (2024-03 Fastrack)

neutralHP removes four redundant VW spec lines: Rabbit Cabriolet 1780, Scirocco 1588, Scirocco 1780 8-valve, Scirocco 1588.

In HP Spec Lines, delete the following redundant spec lines in their entirety:
Spec line #10 - VW Rabbit Cabriolet 1780
Spec line #3 - VW Scirocco 1588
Spec line #4 - VW Scirocco 1780 (8-valve) (83-88)
Spec line #5 - VW Scirocco 1588

2024-03-01 FP Update FP Protege (01-03) Model Info

#35715 from Production Committee · Rule change · TB 24-03 (2024-03 Fastrack)

neutralFP Mazda Protégé ES (01-03) model designation updated to include /5 variant.

In FP Spec Lines, Mazda Protégé ES (01-03) change vehicle as follows:
"Mazda Protégé ES/5 (01-03)"

2024-05-01 GT2 Request for Spec Line 1010 Reconsideration

#35009 from Kristofer Olson · Rule change · TB 24-05 (2024-05 Fastrack)

slowerGT2-ST Acura NSX minimum weight raised to 3000 lbs, restrictor increased to 45mm TIR.

In GT2-ST Spec Lines, Acura NSX, change as follows:
Minimum Weight: "~~2700~~ 3000"
Restrictor: "43 45mm TIR"

2024-05-01 FP Request to Replace CRX Plastic Panels

#35876 from Darryl Saylor · Rule change · TB 24-05 (2024-05 Fastrack)

neutralFP Honda CRX 84-87 can replace plastic front header, rocker skirt, door cap panels with stock-appearance replicas in alternate materials.

In FP spec line "Honda CRX / CRX Si (84-87)", add the following wording to the Notes section:
"The plastic OE front header/nose body panel, lower rocker side-skirt, and lower door cap panel can be replaced by a
replica, which may be constructed of an alternate material, provided its appearance remains stock."

2024-05-01 GT2 Request to Eliminate the FPR from the Corvette (-2013) with LS2

#35878 from Michael Quattlebaum · Rule change · TB 24-05 (2024-05 Fastrack)

fasterGT2-ST Corvette 14-19 LS2 restrictor increases from 78mm to 80mm flat plate.

In GT2-ST Spec Lines, Chevrolet Corvette (14-19), change Restrictor as follows:
"78 80mm flat plate"

2024-05-01 FP FP data and parity

#35896 from Production Committee · Rule change · TB 24-05 (2024-05 Fastrack)

slowerFP Acura Integra and Honda Civic models now require 55mm Flat Plate Intake Restrictor.

In the following FP spec lines, add the following wording to the Notes section:
Acura Integra (90-93)
Acura Integra LS (94-01)
Acura Integra GSR (92-93)
Honda Civic Del Sol VTEC (94-97)
Honda Civic Si (99-00)
"55mm Flat Plate Intake Restrictor is required."

2024-06-01 FP NIssan 300ZX Z31 to EP

#35830 from Murphy Nichols · Rule change · TB 24-06 (2024-06 Fastrack)

neutralNissan 300ZX 84-89 classified to EP at 2550 lbs minimum, 2960cc 6-cyl SOHC, fuel injection, 12.0:1 compression limit, 0.500" valve lift limit.

In EP Spec Lines, classify Nissan 300ZX (84-89), as follows:

A specification table follows in the original; it is not shown here.

2024-06-01 FP RX7 1993 and Up Request In EP Spec Lines, classify

#36031 from Edward Zabinski · Rule change · TB 24-06 (2024-06 Fastrack)

neutralMazda RX-7 92-97 newly classified EP Prep Level 2 at 2200–2310 lbs with 13B 6-port rotary engine.

Mazda RX-7 (92-97) as follows:

A specification table follows in the original; it is not shown here.

2024-06-01 FP Clean-up Multiple EP RX-8 Spec Lines In EP

#36156 from Production Committee · Rule change · TB 24-06 (2024-06 Fastrack)

neutralEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.

Spec Lines, make the following changes to the two Mazda RX-8 spec lines.
Remove spec line entirely:
~~Mazda RX-8 (04-11)~~
Remove the wording "alternate":
Mazda RX-8 (04-11)~~(alternate)~~
Spec Mazda (SM/SMX) None.

2024-07-01 GT2 GT2-ST Rule Clarification

#36093 from Dominic Starkweather · Rule change · TB 24-07 (2024-07 Fastrack)

neutralGT2-ST allows aftermarket replacement differential housings if exact equivalents.

In GCR Section, Appendix K. 2012.M2, add the following:
"After market replacement differential housings are permitted as long as they are an exact equivalent."

2024-07-01 GT2 GT4 cars may run in GT2-ST

#36235 from Grand Touring Committee · Rule change · TB 24-07 (2024-07 Fastrack)

neutralGT4 cars now permitted in GT2-ST with factory restrictor, must comply with 2012 STO rules, slicks allowed with 100-pound penalty.

In 9.1.2. GT2 Spec Lines, GT3 Cars, change Note as follows:
"Note: All GT4 cars are permitted to compete in GT2-ST provided they use a factory supplied power stick or Pro Series
required restrictor. Must have GT4 rules in possession at all race events. Cars must comply with 2012 STO rules as
stated in Appendix K of the GCR. Engine Displacements in this table are nominal. Each competitor shall have available
definitive documentation (e.g., factory manual) of the original displacement for the engine used. Slicks allowed on all
GT2/ST cars with a 100-pound weight penalty."

2024-08-01 FP Errant entry in HP production line item

#36231 from Angus Crome · Rule change · TB 24-08 (2024-08 Fastrack)

neutralHP Volkswagen Golf and Jetta 85-92 track correction: front 1537mm (60.5in), rear 1529mm (60.2in).

In HP Spec Lines, change Track (F/R)mm/(in.) as follows:
Volkswagen Golf (GTI, GT, GL) (85-92): "2 1537/1529 (60.5/60.2)"
Volkswagen Jetta (GLI, GL) (85-92): "2 1537/1529 (60.5/60.2)"

2024-10-01 FP Errors/emissions Honda Civic/CRX

#36700 from Martin Burk · Rule change · TB 24-10 (2024-10 Fastrack)

fasterFP Honda CRX/CRX Si 84-87 block material changes from Iron to Alum.

In FP Spec Lines, Honda CRX / CRX Si (84-87), change Block Mat'l as follows:
"~~Iron~~ Alum"

2024-11-01 FP 1275 HP Spridget Level 2 Only

#36518 from Darryl Saylor · Rule change · TB 24-09 (2024-09 Fastrack)

fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.

In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows:
"(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows:
"(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"

2025-01-01 GT2 Panoz Esperante GTS BOP

#36686 from Brian Goldburg · Rule change · TB 25-01 (2025-01 Fastrack)

neutralGT2 Panoz Esperante GTS adds 2013-2016 Ford EcoBoost Twin Turbo V-6 3496cc engine, 2600 lbs.

In GT2 SPEC LINES, GT Engines - PANOZ, classify 2013-2016 Ford EcoBoost Twin Turbo as follows:
GT Engines – PANOZ
Engine
Family
Engine Type Bore x
Stroke
(in.)
Disp.

Show 2 more lines

(CC)
Head Type Valves /

A specification table follows in the original; it is not shown here.

2025-01-01 FP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line

#37119 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)

fasterEP BMW 325i/is E30 (84-91) weight reduced 50–52 lbs across three spec lines to 2150, 2204, 2258.

In EP SPEC LINES, BMW 325i/is (E30) (84-91), change Weight as follows:
"~~2200~~ 2150
*~~2255~~ 2204
**~~2310~~ 2258"

2025-01-01 GT2 Correct language regarding OEM Areo Devices

#37137 from Christopher Childs · Rule change · TB 25-01 (2025-01 Fastrack)

neutralTA2 rear wing height rule clarified: OEM aerodynamic devices exempt from peak-of-roof requirement.

In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows:
"B. Aerodynamic Devices
2. Rear wing
c. The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level
with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule."

A specification table follows in the original; it is not shown here.

2025-01-01 GT2 GT2 Sunbeam Tiger Alternate Carburetor

#37198 from Tom Patton · Rule change · TB 25-01 (2025-01 Fastrack)

neutralGT2 Sunbeam Tiger gains Holly 650 cfm carburetor alternate options PN #80541-1 and #80541-2.

In GT2 Spec Lines, GT Engines - SUNBEAM, add to Fuel Induction as follows:
"Carburetors(s) Holly 650 cfm PN #80541-1 and PN #80541-2"

2025-01-01 FP Fix Error in Spridget Spec Line

#37437 from Jason Stine · Rule change · TB 25-01 (2025-01 Fastrack)

neutralFP Spridget and Midget 1275cc and 1500cc spec line corrections to bore, stroke, displacement, and valve sizes.

In FP SPEC LINES, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change the following:
1275cc:
Bore x Stroke: "~~68.1x78.4 (2.68x3.09)~~ 70.6x81.3 (2.78x3.20)"
Displacement: "~~(77.78)~~ 1275"
Valves IN & EX: ~~"(I) 32.1/(1.26) (E) 28.4/(1.12)~~ (I) 33.3/(1.31) (E) 29.5/(1.16)"
1500cc:
Bore x Stroke: "~~1.1x84.3~~ 73.7x87.4 (2.90x3.44)"
Displacement: "~~1491 (90.95)~~ 1493"

Show 1 more lines

Valves IN & EX: "(I) 36.6/(1.44) (E) ~~28.7~~ 29.7/(1.17)"

2025-01-01 FP Create ruleset that allows GTL cars to run in FP

#37485 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)

neutralF Production now allows GT-Lite cars meeting Appendix N specifications to compete, effective 2025-01-01.

“~~(Effective January 1, 2026)~~ (Effective January 1, 2025)." Any GT-Lite (GTL) car meeting all of the requirements of Appendix N
GT-LITE CATEGORY SPECIFICATIONS for inclusion into F PRODUCTION" may compete in the F-Production class. For GTL cars
competing in FP, the level of preparation and modifications will be determined by Appendix N and not by PCS 9.1.5.”

2025-02-01 GT2 GT2/ST - Remove Aftermarket/Racing ABS penalty

#36538 from Jorge A Nazario · Rule change · TB 25-02 (2025-02 Fastrack)

fasterGT2 STO aftermarket ABS weight penalty reduced from 100 lbs to 50 lbs.

In GCR, Appendix K. 2012 STO Rules, O.9., change as follows:
"May run OEM ABS or convert to an aftermarket ABS controller with ~~100~~ 50 lb. weight penalty."

2025-02-21 FP Effective date for Jan 2025 GCR updates

#37654 from Doug Piner · Rule change · TB 25-02 (2025-02 Fastrack)

slowerEP BMW Z3 2.5L requires 52mm flat plate intake restrictor; Z3 2.8L 55mm; 328i/is E36 58mm; 328i/ci E46 58mm; 325i/is E46 56mm; 325i/is E36 56mm; 325is M-Technic 56mm.

In EP Spec Lines, add to Notes as follows:
BMW Z3 2.5LL "(Effective 2/21/2025) 52mm Flat Plate Intake Restrictor is required."
BMW Z3 2.8L (97-00): "(Effective 2/21/2025) 55mm Flat Plate Intake Restrictor is required."
BMW 328i/is E36 (96-99): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required."
BMW 328i/ci E46 (01-06): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required."
BMW 325i/is E46 (01-06): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."
BMW 325i/is E-36 (92-95): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."
BMW 325is M-Technic (1994): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."

Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21

2025-03-01 GT2 Hood Bulge allowed

#37000 from Gordon Leslie · Rule change · TB 25-03 (2025-03 Fastrack)

unclearGT2 Pontiac Fiero changes from FWD to RWD; hood bulge permitted for front engine relocation.

In GT2 Spec Lines, GT2 Cars - PONTIAC, Fiero, change as follows:
Drive-line: "~~FWD~~ RWD"
Add to Notes: "Hood bulge permitted as requested for front engine relocation only."

2025-03-01 FP Request Competition Adjustment to BMW Z3 2.5L

#37120 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)

slowerEP BMW Z3 and 3-series models get smaller intake restrictors: Z3 2.5L to 52mm, Z3 2.8L to 55mm, 328i to 58mm, 325i to 56mm.

In EP Spec Lines, change Notes as follows:
BMW Z3 2.5LL "(Effective 3/1/2025) ~~56mm~~ 52mm Flat Plate Intake Restrictor is required."
BMW Z3 2.8L (97-00): "(Effective 3/1/2025) ~~59mm~~ 55mm Flat Plate Intake Restrictor is required."
BMW 328i/is E36 (96-99): "(Effective 3/1/2025) ~~62mm~~ 58mm Flat Plate Intake Restrictor is required."
BMW 328i/ci E46 (01-06): "(Effective 3/1/2025) ~~62mm~~ 58mm Flat Plate Intake Restrictor is required."
BMW 325i/is E46 (01-06): "(Effective 3/1/2025) ~~60mm~~ 56mm Flat Plate Intake Restrictor is required."
BMW 325i/is E-36 (92-95): "(Effective 3/1/2025) ~~60mm~~ 56mm Flat Plate Intake Restrictor is required."
BMW 325is M-Technic (1994): "(Effective 3/1/2025) ~~60mm~~ 56mm Flat Plate Intake Restrictor is required."

2025-03-01 FP Interpretation of Production Rules on Mirrors

#37235 from Lawrence Slivinski · Rule change · TB 25-03 (2025-03 Fastrack)

neutralEP, FP, HP: interior or exterior mirrors meeting rule 9.3.36 now permitted.

In GCR, add new rule as Section 9.1.5.E.10.f:
"Any interior or exterior mirror(s) that meets rule 9.3.36 may be used."

2025-03-01 FP FP Class Adjustments

#37458 from Production Committee · Rule change · TB 25-01 (2025-01 Fastrack)

slowerFP Acura Integra and Honda Civic models get smaller 51mm intake restrictors, down from 55mm; Del Sol VTEC weight increases to 2290–2405 lbs.

In FP SPEC LINES, change Notes as follows:
Acura Integra (90-93): "(Effective 3/1/2025) ~~55mm~~ 51mm Flat Plate Intake Restrictor is required."
Acura Integra LS (94-01): "(Effective 3/1/2025) ~~55mm~~ 51mm Flat Plate Intake Restrictor is required."
Acura Integra GSR (92-93): "(Effective 3/1/2025) ~~55mm~~ 51mm Flat Plate Intake Restrictor is required."
Honda Civic Si (99-00): "(Effective 3/1/2025) ~~55mm~~ 51mm Flat Plate Intake Restrictor is required.
In FP SPEC LINES, change as follows:
Honda Civic Del Sol VTEC (94-97): "
Weight: "(Effective 3/1/2025) ~~2265 *2322 **2378~~ 2290 *2347 **2405

Show 1 more lines

Notes: "(Effective 3/1/2025) ~~55mm~~ 51mm Flat Plate Intake Restrictor is required."

2025-03-01 FP Weight Reduction for Honda S2000

#37466 from Michael Unger · Rule change · TB 25-03 (2025-03 Fastrack)

fasterEP Honda S2000 1997cc base loses 75 lbs to 2375; 2157cc base loses 60 lbs to 2450.

In EP, Spec Lines make the following weight changes:

A specification table follows in the original; it is not shown here.

2025-03-01 FP Mazda 1999 Miata 1.8L

#37488 from Joe Carr · Rule change · TB 25-03 (2025-03 Fastrack)

fasterEP Mazda MX-5/Miata 99-05 minimum weight drops to 2100 lbs, 2153 lbs with power adder, 2205 lbs with two adders.

In EP Spec Lines, make the following weight change:
Mazda MX-5 /Miata (99-05):
"~~2150~~ 2100
*~~2204~~ 2153
**~~2258~~ 2205"

2025-03-01 GT2 OEM Wing Adjustment

#37590 from Christopher Childs · Rule change · TB 25-03 (2025-03 Fastrack)

slowerTA2 and STO OEM wings no longer exempt from rear wing height rule at roof peak.

In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows:
"The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of
the roof. ~~OEM aerodynamic devices do not need to adhere to the height rule.~~"
In GCR, Section APPENDIX K. 2012 STO GENERAL TECHNICAL REGULATIONS, D.4.b., add the following:
"Factory wings, and spoilers, and roof vortex generators are permitted, but must be removed if an approved aftermarket wing is
installed. OEM aerodynamic devices do not need to adhere to the height rule."

2025-03-01 FP Errors & Omissions

#37648 from Bryan Floyd · Rule change · TB 25-03 (2025-03 Fastrack)

neutralFP GTL Volkswagen Jetta Mark IV 4dr FWD 98.2 wheelbase newly classified.

In FP Spec Lines, Appendix N, GTL-FP Cars - Volkswagen, classify Jetta Mark - IV as follows:
GTL-FP Cars - VOLKSWAGEN
Model Years Body Style Drive-line Wheelbase (in) Notes
Jetta Mark - IV 4dr FWD 98.2

2025-03-01 FP GTL/FP consolidation 2025 Rules

#37659 from James Gregorius · Rule change · TB 25-03 (2025-03 Fastrack)

neutralFP Spec Lines option: carburettor chokes permitted as alternative to SIR, same size as listed SIR.

In FP Spec Lines, Appendix N: L.9, Fuel Injection System, add the following:
"As an option, induction system “Chokes” may be used where a SIR is required. Said chokes shall be fitted to each barrel of
carburetor/throttle body and all airflow into engine must pass through them. Choke size will be the same as listed SIR unless
noted."

2025-04-01 FP Request for Classification of Chevrolet Spark

#37755 from Kristian Smith · Rule change · TB 25-04 (2025-04 Fastrack)

neutralChevrolet Spark 16-22 classified HP Pre at 1850 lbs minimum weight, fuel injected, 1399 cc.

In HP Spec Lines, classify the Chevrolet Spark (16-22):

A specification table follows in the original; it is not shown here.

2025-04-01 FP Request to Lower Ford Festiva Minimum Weight to 1600 LBS

#37939 from Doug DeRonne · Rule change · TB 25-04 (2025-04 Fastrack)

fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.

In HP Spec Lines "Ford Festiva (88-93)" change as follows:
Weight:
"~~1700~~ 1600
*~~1743~~ 1640
**~~1785~~ 1680"
Notes:
"Compression ratio limited to ~~10.5~~ 11.0:1. Valve lift limited to .450”."

2025-06-01 FP Base Weight Adjustment for H-Production X1/9 Spec Lines

#38255 from Matthew Brannon · Rule change · TB 25-06 (2025-06 Fastrack)

fasterHP Fiat X-1/9 base weights reduced 50–53 lbs across 1300 and 1500 spec lines.

In HP Spec Lines, change Weight as follows:
Fiat X-1/9 & Bertone1500: “~~1790~~ 1740 *~~1835~~ 1784 **~~1880~~ 1827”
Fiat X-1/9 1300: “~~1650~~ 1600 *~~1691~~ 1640 **~~1733~~ 1680”
Fiat X-1/9 1300: “~~2060~~ 2010”
Fiat X-1/9 1500: “~~1950~~ 1900”

2025-07-01 FP BMW Z4 update

#38490 from Bryce McGuire · Rule change · TB 25-07 (2025-07 Fastrack)

slowerEP BMW Z4 03-05 restricted to 52mm flat plate intake restrictor.

In EP Spec Lines, BMW Z4 (03-05), add to Notes the following:
“52mm Flat Plate Intake Restrictor.”

2025-07-01 FP EP Fiat 124 Spider Competition Adjustment Request

#38498 from John Baucom · Rule change · TB 25-07 (2025-07 Fastrack)

fasterEP Fiat 124 Spider 1600 & 2000 weight drops 50 lbs to 2000; carburetors gain 2mm chokes to 36mm.

In EP Spec Lines, Fiat 124 Sport Spider 1600 & 124 Spider 2000, change as follows:
Weight: "~~2050~~ 2000"
Carburetor No. & Type: "(2) Weber 40 IDF-40IFI, (2) Solex C40P116, 34 36mm choke(s) req’d, (2) Weber 45DCOE w/ 34 36 mm
choke(s) on I.R. manifold or fuel injection."

2025-08-01 GT2 Rear Deck Lid for Older Air-Cooled Porsche

#38506 from Justin Erion · Rule change · TB 25-08 (2025-08 Fastrack)

neutralGT2 Porsche 911 Coupe & Targa may use 993 3.8 RSR rear deck lid or approved aftermarket reproductions.

In GT2 Spec Lines, GT2 Cars-Porsche, 911 Coupe & Targa., add to Notes the following:
"Porsche 911-based race cars (911,963,994), the use of the 993 3.8 RSR rear deck lid/spoiler is permitted. Aftermarket
reproductions of the original Porsche Motorsports deck lid provided they faithfully replicate OEM dimensions and functionality,
are acceptable for use."

2025-10-01 FP HP Plymouth Arrow spec omission

#38995 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

neutralHP Plymouth Arrow transmission max speeds clarified to 4 or 5.

In HP Spec Lines, Plymouth Arrow (76-80), add the following wording to Trans. Speeds(max):
"4 or 5"

2025-10-01 FP Add Wheel Diameter to Appendix G

#39008 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

neutralEP, FP, HP wheel diameter added to Appendix G as absolute maximum specification.

In Appendix G.2.3, change as follows:
"Rim width and diameter are is absolute maximums."

2025-10-01 FP Add TB ID tolerance to general Prod rules

#39009 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

neutralEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.

In GCR, Section 9.1.5.E., change as follows:
9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain
stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished."
9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must
remain stock (tolerance of +/-.25mm)."

2025-11-01 FP Please Lower Weight of 280Z

#38871 from Matthew Miller · Rule change · TB 25-09 (2025-09 Fastrack)

fasterEP Nissan 280Z minimum weight reduced from 2560 to 2400 lbs.

In EP Spec Lines, Nissan 280Z, change Weight (lbs) as follows:
"(Effective 11/1/2025) ~~2560~~ 2400
*~~2624~~ 2460
**~~2688~~ 2520"

2025-11-01 FP Miata Weight Adjustment Follow Up

#38949 from Don Tucker · Rule change · TB 25-10 (2025-10 Fastrack)

fasterEP Mazda MX-5 1.8L 90-97 weight reduced to 2125 lbs from 2150 lbs.

In EP Spec Lines, Mazda MX-5 / Miata 1.8L (90-97), Effective 11/1/2025 make the following weight change:
"~~2150~~ 2125"

2025-11-01 FP Weight Break for 1098 Midget / Sprite

#38970 from Kendall Jones · Rule change · TB 25-10 (2025-10 Fastrack)

fasterHP Austin-Healey Sprite/Midget 1098cc minimum weight drops 80 lbs to 1550.

In HP Spec Lines, Austin-Healey Sprite/Midget 1098cc, Effective 11/1/2025make the following weight change:
"~~1630~~ 1550"

2025-11-01 FP HP Volvo 142 spec omission

#38994 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".

In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes:
"Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."

2025-11-01 FP HP Mini DOHC 1.6

#38996 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".

In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following
changes to the Notes:
"Compression ratio limited to 11.0:1, Valve lift limited to ~~.450”~~.390"."

2025-11-01 FP 83-88 FP Scirocco Spec Line Creation

#38997 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

neutralFP Scirocco 83-88 established as spec line with 1733–1803 lbs, 1715–1780 cc SOHC, 40/33 mm valves, Solex carbs or fuel injection.

In FP Spec Lines, classify Volkswagen Scirocco (83-88) as follows:

A specification table follows in the original; it is not shown here.

2025-11-01 FP Add to Rabbit description

#39019 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

neutralFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.

In FP Spec Lines, make the following spec line correction:
"Volkswagen Rabbit (Includes ~~Convertible~~ Cabriolet)"
In HP Spec Lines, make the following spec line correction:
"Volkswagen Rabbit 1588 (Includes Cabriolet)"
"Volkswagen Rabbit 1715 (Includes Cabriolet)"
"Volkswagen Rabbit 1780 (Includes Cabriolet)"

2025-11-01 FP Clean-up 9.1.5.E.7e

#39025 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

neutralEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.

In GCR, Section 9.1.5.E.7., change as follows:
"e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. N~~ote that the “Brakes Std.” and “Brakes~~
~~Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear~~
~~disc brakes under this rule~~. When converting from rear drum brakes to rear disc brakes:
1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on
the vehicle’s spec line.
2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. ~~The standard and~~
~~alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock~~

Show 3 more lines

~~from converting to rear disc brakes under this rule.~~
3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes
as stock from converting to rear disc brakes under this rule."

2025-11-01 FP Add TB size to Ford Mustang (94-98) Spec Line

#39130 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

neutralEP Ford Mustang (94-98) fuel injected throttle body inside diameter specified at 60.

In EP Spec Lines, Ford Mustang (94-98) add the following to the Fuel Injected Equipped Throttle Body Inside Diameter column:
"60"

2025-11-01 FP Correct Existing VW Scirocco Spec Line

#39140 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

fasterFP Volkswagen Scirocco: remove two engine variants (1715cc and 1780cc), lighten one variant to 1663 lbs, allow 15×7 wheels instead of 13×7.

In FP Spec Lines, Volkswagen Scirocco, change spec line as follows:

A specification table follows in the original; it is not shown here.

2025-12-01 FP TR2 Notes E&O

#39180 from Anthony Parker · Rule change · TB 25-12 (2025-12 Fastrack)

unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.

In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes:
"Front apron assembly may be made of alternate material. ~~Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990~~
~~lbs.~~ Laycock overdrive, may use 5 speed gearbox without overdrive."

2025-12-01 FP Balance of Power

#39187 from Jim Simaras · Rule change · TB 25-12 (2025-12 Fastrack)

slowerEP BMW Z3 2.5L restrictor reduced 52mm to 50mm, weight increased to 2550 lbs base; five other BMW models get smaller restrictors.

In EP Spec Lines, make the following changes to Restrictors:
BMW Z3 2.5L: "~~52mm~~ 50mm Flat Plate Intake Restrictor"
BMW Z3 2.8L (97-00): "~~55mm~~ 53mm Flat Plate Intake Restrictor"
BMW 328i/is E36 (96-99): "~~58mm~~ 55mm Flat Plate Intake Restrictor"
BMW 328i/ci E46 (01-06): "~~58mm~~ 55mm Flat Plate Intake Restrictor"
BMW 325i/is (E46) (01-06): "~~56mm~~ 53mm Flat Plate Intake Restrictor"
BMW 325is M-Technic (1994): "~~56mm~~ 53mm Flat Plate Intake Restrictor"
BMW 325i/is E-36 (92-95): "~~56mm~~ 53mm Flat Plate Intake Restrictor"

Show 4 more lines

In EP Spec Lines, BMW Z3 2.5L, change Weight as follows:
"~~2500~~ 2550
*~~2563~~ 2614
**~~2625~~ 2678"

2025-12-01 FP Competition Adjustment Request

#39259 from David Strittmatter · Rule change · TB 25-12 (2025-12 Fastrack)

fasterFP Lancia Scorpion minimum weight drops 80 lbs, to 1950.

In FP Spec Lines, Lancia Scorpion, change Weight as follows:
"~~2030~~ 1950"

2025-12-01 FP Factory Roll Bar Removal on VW Convertible

#39268 from Tim Linerud · Rule change · TB 25-12 (2025-12 Fastrack)

neutralFP Volkswagen Rabbit Convertible no longer required to remove factory roll bar.

In FP Spec Line, Volkswagen Rabbit (Includes Convertible), remove the following wording in Notes:
"~~Factory roll bar must be removed on Cabriolet.~~"

2025-12-01 FP FP Parity Request

#39325 from Mason Workman · Rule change · TB 25-12 (2025-12 Fastrack)

slowerFP Acura Integras and Honda Civics gain 50–79 lbs; Mazda Miata and Mercury Capri compression ratio to 11.0:1, valve lift to .425".

In FP, change Weight as follows:
Acura Integra (90-93):
"~~2235~~ 2285
*~~2291~~ 2342
**~~2347~~ 2399"
Acura Integra LS (94-01):
"~~2260~~ 2310
*~~2317~~ 2368

Show 16 more lines

**~~2373~~ 2426"
Acura Integra GSR (92-93):
"~~2325~~ 2375
*~~2383~~ 2434
**~~2441~~ 2494"
Honda Civic Del Sol VTEC (94-97):
"~~2290~~ 2340
*~~2347~~ 2399
**~~2378~~ 2457"
Honda Civic Si (99-00):
"~~2250~~ 2300
*~~2306~~ 2358
**~~2363~~ 2415"
FP Spec Lines, change Notes as follows:
Mazda Miata 1.6L (90-97): "Comp. Ratio limited to ~~10.0:1~~ 11.0:1, Valve lift limited to ~~.390”~~ .425"."
Mercury Capri 1.6L (91-94): "Comp. Ratio limited to ~~10.0:1~~ 11.0:1, Valve lift limited to ~~.390”~~ .425"."

2025-12-01 FP Adjust former-GTL Honda's with B/D-Series Engines

#39374 from Production Committee · Rule change · TB 25-12 (2025-12 Fastrack)

slowerFP Honda B/D-series engines gain 105–120 lbs minimum weight across seven variants.

In GCR, Appendix N GTL inclusion into FP, Engines - HONDA, change Disp. (cc) – Weight (lbs) as follows:
"D15 – 1493cc – ~~1895~~ 2000
D15b7 – 1493cc – ~~1895~~ 2000
D16 – 1590cc – ~~1945~~ 2055
D16A – 1590cc – ~~1945~~ 2055
B16A – 1595cc – ~~1950~~ 2065
B18 – 1797cc – ~~2050~~ 2170
B18 – 1834cc – ~~2065~~ 2185"

2026-01-01 GT2 Additional Body Options to Replace Older Stock Car Bodies

#39086 from Samuel Daniels · Rule change · TB 26-01 (2026-01 Fastrack)

neutralGT2 adds Cadillac CTS, Chevrolet Impala/Malibu/Monte Carlo/SS, Dodge Intrepid, Ford Fusion/Taurus, Lincoln MKS, Pontiac G8/GTO/Grand Prix, Toyota Camry, and Gen late Model Stock Car bodies.

In GCR, Section 4.8.4.2.1., add the following:
"Cars in the class must use 1997, through current year, commercially available stock car bodywork. The following make/model
bodies are allowed:
1. Cadillac CTS
2. Chevrolet Impala
3. Chevrolet Malibu
4. Chevrolet Monte Carlo
5. Chevrolet SS

Show 12 more lines

6. Dodge Intrepid
7. Ford Fusion
8. Ford Taurus
9. Lincoln MKS
10. Pontiac G8
11. Pontiac GTO
12. Pontiac Grand Prix
13. Toyota Camry
Gen late Model Stock Car Bodies are allows:
1. Chevrolet Camaro
2. Ford Mustang
3. Toyota Camry"

2026-01-01 GT2 GT3 Turbo to GT2?

#39365 from Chris Edens · Rule change · TB 26-01 (2026-01 Fastrack)

neutralGT2 Mazda BP engine 1839cc classified with 46mm turbo inlet restrictor, 2250 lbs minimum weight.

In GT2 Spec Lines, Engines - MAZDA, classify Engine Family BP as follows:
GT2 Engines - MAZDA
Engine
Family
Engine Type Bore x Stroke
(mm)
Disp.
(CC)

Show 1 more lines

Head Type Valves /

A specification table follows in the original; it is not shown here.

2026-01-01 GT2 Tech Bulletins for GT2 and GT2-ST

#39537 from Grand Touring Committee · Rule change · TB 26-01 (2026-01 Fastrack)

slower991.2 GT3 Cup throttle body restrictor increases from 65mm to 70mm; 997.2 loses 100 lbs to 2800; Corvette LS engines get larger restrictors across multiple displacements and model years; LS3 and LT1 weight reduced 100 lbs each to 3150.

In GT2 Spec Lines, GT2 Cars – Porsche, classify 992.1 GT3 Cup as follows:
GT2 Cars – Porsche
Model Year Body
Style Driveline Wheel Base Notes
992.1
GT3 Cup
(22-25) 2 Dr RWD 4.0L flat six. 3250lbs. w/60mm Throttle Body Restrictor (TBR).
Cars must be prepared in accordance with the appropriate

Show 49 more lines

model/year Porsche factory 911 GT3 Cup parts
catalog/service manual. Cars may not be altered in any way
except as authorized below. Drivers must have the correct
year manuals as they apply to their specific car in their
possession. Safety, drivers comfort, driver control and
instrumentation items may be modified per the GCR. Original
factory installed Matter/ IMV roll cages are allowed. The
stock unmodified fuel tank is allowed. Windshield clips must
be installed per GCR 9.3 Windshield Clips/Rear Window
Straps. All other SCCA safety standards apply. Tires per GCR
9.3 Tires. Lubricants, consumable fluids (brake fluid, coolant
etc.) and oil filters are open free. Factory (OEM manufacturer)
Lexan front windows allowed as delivered. ABS is allowed.
In GT2 Spec Lines, GT2 Cars – Porsche, change Notes as follows:
991.1 GT3 Cup: "3.8L flat six. 3000lbs. ~~w/72mm Throttle Body Restrictor (TBR).~~ Aftermarket header allowed."
991.2 GT3 Cup: "4.0L flat six. 3000lbs. w/~~65mm~~ 70mm Throttle Body Restrictor (TBR)."
997.2 GT3 Cup: "3.8L flat six. ~~2900~~ 2800 lbs. Aftermarket header allowed."
In GT2 Spec Lines, GT2 – ST, Chevy Corvette (-2013), change as follows:
5665:
Restrictor: "81 85mm flat plate"
Notes: "GM LS1, LS6. LS1/LS6 C6 Corvettes using the OEM C6 intake manifold and 90 mm throttle body must use a ~~78mm~~ flat
plate restrictor. OEM 75mm throttle body and manifold do not require a restrictor. LS~~6 may reduce weight by 50 lbs. L~~ S1/LS6
alternate intake manifold, DORMAN part # 615-900."
LS2 5967 Restrictor: "83 85mm "
L76 5967 Restrictor: "80 83mm flat plate"
LS3 6162 Restrictor: "80 83mm flat plate"
6162 GM LS3:
Weight: "~~3250~~ 3150"
Restrictor: "74 80mm flat plate"
6162 GM LT1:
Weight: "~~3250~~ 3150"
Restrictor: "74 77mm flat plate"
In GT2 Spec Lines, GT2 – ST, Chevy Corvette (14-19), change as follows:
5665:
Restrictor: "83 85mm flat plate"
Notes: "GM LS1, LS6. LS1/LS6 C6 Corvettes using the OEM C6 intake manifold and 90 mm throttle body must use a ~~78mm~~ flat
plate restrictor. OEM 75mm throttle body and manifold do not require a restrictor. LS~~6 may reduce weight by 50 lbs. L~~ S1/LS6
alternate intake manifold, DORMAN part # 615-900."
LS2 5967:
Weight: "~~3100~~ 3000"
Restrictor: "83 85mm flat plate"
L76 5967 Restrictor: "80 83mm flat plate"
6162 Restrictor: "80 83mm flat plate"
6162 LS3:
Weight: "~~3200~~ 3100"
Restrictor: "77 80mm flat plate"
6162 LT1:
Weight: "3~~200~~ 3100"
Restrictor: "74 80mm flat plate"

2026-02-01 FP Request Toyota 5E Series Engines

#38208 from Scott Schick · Rule change · TB 26-02 (2026-02 Fastrack)

neutralFP class adds Toyota 5E DOHC 1497cc engine, 1900 lbs minimum weight, 23mm SIR induction.

In FP Appendix N, add spec line for the Toyota 5E engine to the "Engines - TOYOTA" section:

A specification table follows in the original; it is not shown here.

2026-02-01 FP Request for Toyota 4E Series Engines

#38209 from Scott Schick · Rule change · TB 26-02 (2026-02 Fastrack)

neutralFP Toyota 4E DOHC 1331cc engine added to Appendix N with 1900 lbs minimum weight.

In FP Appendix N, add spec line for the Toyota 4E engine to the "Engines - TOYOTA" section:

A specification table follows in the original; it is not shown here.

2026-02-01 GT2 Allow Larger Air Cooled Engines in Porsche 911 GT2

#39249 from Justin Erion · Rule change · TB 26-02 (2026-02 Fastrack)

fasterGT2 Porsche 911 SC gains option of 4.0L 4V engine at 2350 lbs or 4.0L 2V at 2275 lbs.

In GT Spec Lines, create GT Cars - PORSCHE and classify SC as follows:
GT Cars - PORSCHE
Model Years Body Style Drive- line Wheel- base
(in)
Notes
SC 1978 2 Dr. Rear engine/RWD 89.45 May use alternate engine bore.
4.0L 2V @2275 lbs. 4.0L 4V @ 2350 lbs.

2026-02-01 GT2 Classify T1 BMW in GT2

#39408 from Jared Lendrum · Rule change · TB 26-02 (2026-02 Fastrack)

neutralM3 E92 classified in GT2 with 3999cc V8, 35mm restrictor, 3300 lbs minimum weight.

In GT Spec Lines, classify M3 E92 in GT Cars - BMW as follows:
GT Cars - BMW
Model Years Body Style Drive-
line
Wheel-
base (in)
Notes
M3 E92 (08-13) 2 Dr. RWD 108.7 Cannot be built to any other rule set.

Show 5 more lines

In GT Spec Lines, classify M3 E92 in GT Engines - BMW - BMW as follows:
GT Engines - BMW
Engine
Family
Engine Type Bore x Stroke

A specification table follows in the original; it is not shown here.

2026-02-01 FP Dual Carbs for the Fiat X1/9

#39593 from Daniel Snow · Rule change · TB 26-02 (2026-02 Fastrack)

unclearFP Fiat X1/9 gains dual carburetor options with 28mm side-draft alternates and revised valve/transmission specs.

In FP Spec Lines, change as follows:
Fiat X-1/9 & Bertone 1300:
"(1) Weber 32 DMTR or DATRA/100 w/32mm bores
(1) 40 DCNF w/32mm choke(s)
(2) auto-type side-draft w/28mm choke(s) on I.R. manifold
Orientation of the alternate carburetor is unrestricted. The alternate carb adapter may not be thicker than 1.25”. The adapter
may have a bore larger than the throttle bore of the approved alternate carburetor.
Valve Size: (I) 35.5/(1.40) (E) 31.3/(1.23)~~30.5/(1.20) (E) 1.23~~

Show 10 more lines

Trans. Speeds: 5"
Fiat X-1/9 & Bertone:
"Fuel Injection
(1) 34 DMTR~~, (1) 36 DCNF w/34mm choke(s), or (1) 40DCNF w/34mm choke(s)~~
(1) 36 or 40 DCNF w/34mm choke(s)
(2) auto-type side-draft w/28mm choke(s) on I.R. manifold
Orientation of the alternate carburetor is unrestricted. The alternate carb adapter may not be thicker than 1.25”. The adapter
may have a bore larger than the throttle bore of the approved alternate carburetor.
Valve Size: (I) 35.5/(1.40) (E) 33.0/(1.30)
Trans. Speeds: 5 or 4"

What the rules allowed changed as listed; this does not say what any particular car ran.