STL + P + P2 + FE2 at Buttonwillow Raceway Park

2023-04-01 P2 Remove redundant effective date language and update engine table

#34012 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, change as follows:

2023-04-01 P2 E&O - Correct dimensional equivalents

#34038 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.2, change as follows:
"Height: No part of the vehicle having special or significant aerodynamic function shall exceed a height of 115cm (45.275 inches)
above the ground with the car in normal racing trim, driver aboard."
In P2, GCR section 9.1.8.C.D.3, change as follows:
"However, no portion shall extend more than 10cm (3.937 inches) beyond a plane tangent to the outer face of the front and rear
wheels with tires."
P2 Engine Table
Spec

A specification table follows in the original; it is not shown here.

2023-05-01 P2 Clarify minimum side body height requirement

#34143 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.6, change as follows:
"As viewed from the side, T the outermost surface of side pods body between the front and rear wheel openings and above the
floor must have a minimum height equal to the height of the front axle centerline."

2023-05-01 P2 Clarify closed cockpit single seat car allowance

#34144 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.C, add a section as follows:
"4. Closed cockpit single seat cars are not permitted unless specifically allowed by a spec line in Table 1."

2023-06-01 STL Clarify STL table B - IT spec notes on Tires

#34187 from Austin Hilliard · Rule change · TB 23-06 (2023-05 Fastrack)

Summary

As printed in Fastrack

In STL Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Notes as follows:
ITA-spec and ITS-spec RX7: "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires
must also conform to 9.1.4.2.Tires."
ITS, ITA, ITB, or ITC vehicles (1985- ): "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires &
Wheels. Tires must also conform to 9.1.4.2.Tires."

2023-12-01 P2 Correct Table 1 for Engine Date Range Specifications

#35182 from Formula/Sports Racing Committee · Rule change · TB 23-12 (2023-09 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 STL Alternate Carburetor Request for 79-85 RX7 12a

#35181 from Dan Sheppard · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In STL Table B: Alternate Vehicle and Engine Allowances, Mazda RX-7 12A (79-85), change Notes as follows:
"Street Porting of the engine only. Bridge porting, peripheral porting, and eyelash porting are prohibited. Contact SCCA National
Office for details of Street porting. Stock Nikki 4 bbl carburetor on a stock manifold only. or auto-type 2 bbl w/42mm choke(s) on
a “dual-y” manifold. Allow the standard removal of emissions related components, and allow air and fuel jets to be corrected.
Modification of the water jacket in the area of the spark plug for cooling purposes is permitted."

2024-01-01 P2 E&O - Clarify B.1 modified engine range in AMAC spec lines

#35225 from Club Racing Board · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 P2 Replacement Engine Crankcase for 07/08 Suzuki GSX-R1000 Engines

#35340 from Michael A Reupert · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, add to notes as follows:
"No modifications allowed on engines manufactured after 2008 model year. 2007-2008 Suzuki GSX-R1000 crankcase part
#11300-21860 may be replaced with 2016-2019 Suzuki GSX-S1000 crankcase part #11301-04840."

2024-02-01 STL ST Electric-Assisted Steering Systems

#35066 from Jose Osiris Pena · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.M.16., change as follows:
"Power steering may be modified in any of the following ways:
a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be
modified internally to work without pump.
b. an OEM manual steering rack for that model may be fitted
c. an electric power steering pump may be fitted
d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used
e. an OEM hydraulic-assisted steering system may be used"

2024-02-01 STL BOP Adjustments

#35112 from Super Touring Committee · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

As printed in Fastrack

In GCR, 9.1.4.H.1., change as follows:
"Minimum weights for cars with normally aspirated piston engines will be determined by 1.35 lbs/cc displacement for
the installed engine (see the following table). Displacement is the factory displacement for the installed engine. For the
purpose of weight assignment, engine displacement will be rounded to the nearest 50cc (e.g., 2176cc = 2200cc and
2175cc = 2150cc)."
In GCR, 9.1.4.H.1., change Minimum Weight on Chart as follows:
Factory Engine Displacement 1900: "Effective 3-1-24: 2565 2540"
Factory Engine Displacement 1950: "Effective 3-1-24: 2633 2583"

2024-02-01 STL Mazda 12A

#35320 from Super Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)

Summary

As printed in Fastrack

In STL Spec Lines, Table A, Mazda 12A, change Notes as follows:
"The 5th and 6th intake port actuators and valves may be removed or disabled."

2024-05-01 P2 CN Spec ECU

#35835 from Bart Wolf · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line E, change the notes as follows:
"No engine modifications except for dry sump oil system, ECU mapping, and exhaust system the following: oil system, ECU, and
exhaust are unrestricted."

2024-05-01 P2 E&O - Correct FIA Group CN spec line notes

#35900 from Club Racing Board · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, FIA Group CN spec line, change the notes as follows:
"FIA Group CN homologated chassis, brake calipers and discs, hub carriers, and suspension components are required. V de
V European Proto Endurance Series Challenge permitted bodywork, rear diffuser, wing, wheels, and assisted
shifting are allowed. Car M must comply with all other P2 requirements. Competitors must have copies of FIA Group CN
Technical Regulations and V de V European Proto Endurance Series Challenge Sporting and Technical Regulations in their
possession and present them upon request are available here: https://www.scca.com/pages/technical-forms-and-downloads."

2024-12-01 STL Request to Remove Miata Hubs from General category

#37138 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.M.18., change as follows:
"18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda
Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."

2024-12-01 P2 2000 cc Pinto Engine Car Weight

#37187 from Marvin Hodges · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Line E Note 2, add the following:
"8. Minimum weight 1335 lbs."

2025-02-01 P Correct text in engine table notes

#37606 from Club Racing Board · Rule change · TB 25-02 (2025-02 Fastrack)

Summary

As printed in Fastrack

In Prototype Engine Table, Spec Line B, change the notes as follows:
"Staudacher cars may run 950 lb min. wt. minimum weight with 38.5mm flat plate intake restrictor."
In Prototype Engine Table, Spec Line D, change the notes as follows:
"No restrictor required at 1150 lb min. wt. minimum weight."

2025-02-01 P Update Prototype class designation

#37653 from Club Racing Board · Rule change · TB 25-02 (2025-02 Fastrack)

Summary

As printed in Fastrack

In Categories and Classes, GCR section 9.1, change as follows:
"9.1.8. SPORTS RACING CATEGORY CLASSES
A Sports Racing (ASR) Regional Class
Prototype 1 (P1)"
In Homologation Requirements, GCR section 9.2.2, change as follows:
"All Formula, Sports Racing, and P1, and P2 cars must be constructed in strict accordance with the rules and regulations
contained in the current GCR unless specifically excepted."
In Non-Metallic Wheel/Chassis Construction, GCR section 9.3.37, change as follows:

2025-04-01 FE2 Driver Safety & Comfort

#37965 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

As printed in Fastrack

In FE2, GCR section 9.1.1.G.2.E, add the following:
"g. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

2025-05-01 STL E&O: SMX Allowance in STL

#37945 from Greg Amy · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

As printed in Fastrack

In STL Spec Lines, Table B, Mazda Spec MX5 Challenge, change as follows:
Minimum Weight: "2500 See 9.1.7.1."
Notes: "Mazda MX5 Challenge car must utilize the following components: Roush CNC cylinder head 0000-01-5300,Mahle
standard or +0.005 0000-01-5310, OEM camshaft, 11:1 compression ratio, header 0000-06-5407-NC, exhaust 0000-06-5427-NC,
cold air intake 0000- 06-5150-KT, ECU flash 0000-01-5379, Pagid front brake pads 0000-03-5104-SP or endurance pads 0000-03-
5104-EN, Pagid rear brake pads 0000-03-5114-SP or endurance pads 0000-03-5114-EN, Penske front shock 0000-04-5291-SA,
Penske rear shock 0000-04-5292-SA, Penske rear mount kit 0000-04-5358, Front mount kit 0000-04-5359, Front offset bushing
0000-04-5407-NC, Eibach front springs 0000-04-9700-08, Eibach rear springs 0000-04-9400-07, Eibach helper springs 0000-04-

Applies to Mazda Miata on this page: Jared Korth, Ricardo Arruda, Gavin Wardle, Ryan Gutile, Bryce Johnson, Andy Chittum, Adrian Comstock

2025-05-01 P Add missing punctuation marks

#38150 from Club Racing Board · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

As printed in Fastrack

In P Engine Table, Spec Line D notes, add the following:
"No restrictor required at 1150 lbs. minimum weight."
In P Engine Table, Spec Line G notes, add the following:
"Group CN non-composite chassis with Honda K20A-FD2 may use unrestricted individual throttle bodies at 1500 lbs. minimum
weight."
In P Table 1, Beasley B2 spec line notes, add the following:
"Engine must be Mazda 12A rotary with 40.5mm venturi. Car must comply with all other Prototype requirements."
In P Table 1, P2 cars built to 2000cc auto-based specification spec line notes, add the following:

2025-08-01 STL Lotus Weight Reduction

#38772 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)

Summary

As printed in Fastrack

In 9.1.2. GT2/ST Spec Lines, Lotus Evora GT4, change Weight as follows:
"2750 2700"
In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows:
Lotus Elise Cup R: "2300 2250"
Lotus Elise SC/ Lotus Exige SC: "2300 2550
2500 2450"

2025-08-01 P RM 25-05 - Prototype Engine Table A, 2 Cycle Restrictor Change

#38929 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

As printed in Fastrack

Effective 8/1/25 in Prototype Engine Table, Spec Line A, change the restrictor as follows:
"40mm 38mm Restricted Venturi Size"

2025-09-01 P 13B Rotary Engine Rules Change Request

#38856 from Jason Vinkemulder · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

As printed in Fastrack

Effective 9/1/25 in Prototype Engine Table, Spec Line K, change the restrictor as follows:
"40mm SIR with fuel injection or 41.5mm venturi with carburetor"

2025-09-01 P Add Radical Cup series Radical SR3 spec line to Table 1

#38916 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

As printed in Fastrack

Effective 9/1/25 in Prototype Table 1 (Spec Line Cars), add the following:

2025-09-01 P Clarify spec line cars language

#38943 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

As printed in Fastrack

Effective 9/1/25, in Prototype, GCR section 9.1.8.B.K, change as follows:
"P2 cars may compete in either the Prototype class or the P2 class but must participate in the Prototype class to the extent
necessary to qualify for an invitation to the Runoffs in Prototype. P2 cars may be modified to comply with the general Prototype
rules and Prototype Engine Table or may continue to run in P2 specification in the Prototype class as permitted in Table 1 below."
Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2025-10-01 FE2 FE & FE2 Bubble Tail

#38978 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

As printed in Fastrack

In FE, GCR section 9.1.1.G.2.F.k, change as follows:
"Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."

2026-01-01 P Request to Continue to Allow Carbon Brakes

#39476 from Jeffrey Lederman · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In Prototype, GCR section 9.1.8.B.F.2, change as follows:
"Brake calipers may be ferrous or aluminum alloy. Effective 1/1/2026, carbon-carbon and carbon-ceramic brake rotors are
prohibited and rotors must be ferrous. Brake rotor material is unrestricted."

2026-01-01 STL Weight adjustment for STL

#39579 from Super Touring Committee · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.2.H.1. change Minimum Weight on chart as follows:

A specification table follows in the original; it is not shown here.