STL + P2 + FA at Buttonwillow Raceway Park

2023-04-01 P2 Remove redundant effective date language and update engine table

#34012 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, change as follows:

2023-04-01 P2 E&O - Correct dimensional equivalents

#34038 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.2, change as follows:
"Height: No part of the vehicle having special or significant aerodynamic function shall exceed a height of 115cm (45.275 inches)
above the ground with the car in normal racing trim, driver aboard."
In P2, GCR section 9.1.8.C.D.3, change as follows:
"However, no portion shall extend more than 10cm (3.937 inches) beyond a plane tangent to the outer face of the front and rear
wheels with tires."
P2 Engine Table
Spec

A specification table follows in the original; it is not shown here.

2023-05-01 FA E&O - Correct Pro Formula Mazda spec line dimensional equivalent

#34085 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In FA Table 2, Pro Formula Mazda spec line, change as follows:
"The overall maximum width of the bodywork behind the front wheels shall not exceed 132cm (51.17 51.97 inches)."

2023-05-01 FA Add new spec line for MSR Formula Mazda FMzR to Table 2

#34139 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

RM 23-06 – MSR - FMzR Formula Atlantic Classification dated 4/21/2023
In FA Table 2, add a spec line as follows:

2023-05-01 P2 Clarify minimum side body height requirement

#34143 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.6, change as follows:
"As viewed from the side, T the outermost surface of side pods body between the front and rear wheel openings and above the
floor must have a minimum height equal to the height of the front axle centerline."

2023-05-01 P2 Clarify closed cockpit single seat car allowance

#34144 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.C, add a section as follows:
"4. Closed cockpit single seat cars are not permitted unless specifically allowed by a spec line in Table 1."

2023-06-01 STL Clarify STL table B - IT spec notes on Tires

#34187 from Austin Hilliard · Rule change · TB 23-06 (2023-05 Fastrack)

Summary

As printed in Fastrack

In STL Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Notes as follows:
ITA-spec and ITS-spec RX7: "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires
must also conform to 9.1.4.2.Tires."
ITS, ITA, ITB, or ITC vehicles (1985- ): "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires &
Wheels. Tires must also conform to 9.1.4.2.Tires."

2023-06-01 FA Simplify Pro Formula Mazda wheel allowance

#34190 from Club Racing Board · Rule change · TB 23-06 (2023-06 Fastrack)

Summary

As printed in Fastrack

In FA, Pro Formula Mazda spec line, change wheel width as follows:
"Pro Mazda series wheels

A specification table follows in the original; it is not shown here.

2023-12-01 P2 Correct Table 1 for Engine Date Range Specifications

#35182 from Formula/Sports Racing Committee · Rule change · TB 23-12 (2023-09 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 STL Alternate Carburetor Request for 79-85 RX7 12a

#35181 from Dan Sheppard · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In STL Table B: Alternate Vehicle and Engine Allowances, Mazda RX-7 12A (79-85), change Notes as follows:
"Street Porting of the engine only. Bridge porting, peripheral porting, and eyelash porting are prohibited. Contact SCCA National
Office for details of Street porting. Stock Nikki 4 bbl carburetor on a stock manifold only. or auto-type 2 bbl w/42mm choke(s) on
a “dual-y” manifold. Allow the standard removal of emissions related components, and allow air and fuel jets to be corrected.
Modification of the water jacket in the area of the spark plug for cooling purposes is permitted."

2024-01-01 P2 E&O - Clarify B.1 modified engine range in AMAC spec lines

#35225 from Club Racing Board · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 P2 Replacement Engine Crankcase for 07/08 Suzuki GSX-R1000 Engines

#35340 from Michael A Reupert · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, add to notes as follows:
"No modifications allowed on engines manufactured after 2008 model year. 2007-2008 Suzuki GSX-R1000 crankcase part
#11300-21860 may be replaced with 2016-2019 Suzuki GSX-S1000 crankcase part #11301-04840."

2024-02-01 STL ST Electric-Assisted Steering Systems

#35066 from Jose Osiris Pena · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.M.16., change as follows:
"Power steering may be modified in any of the following ways:
a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be
modified internally to work without pump.
b. an OEM manual steering rack for that model may be fitted
c. an electric power steering pump may be fitted
d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used
e. an OEM hydraulic-assisted steering system may be used"

2024-02-01 STL BOP Adjustments

#35112 from Super Touring Committee · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

As printed in Fastrack

In GCR, 9.1.4.H.1., change as follows:
"Minimum weights for cars with normally aspirated piston engines will be determined by 1.35 lbs/cc displacement for
the installed engine (see the following table). Displacement is the factory displacement for the installed engine. For the
purpose of weight assignment, engine displacement will be rounded to the nearest 50cc (e.g., 2176cc = 2200cc and
2175cc = 2150cc)."
In GCR, 9.1.4.H.1., change Minimum Weight on Chart as follows:
Factory Engine Displacement 1900: "Effective 3-1-24: 2565 2540"
Factory Engine Displacement 1950: "Effective 3-1-24: 2633 2583"

2024-02-01 STL Mazda 12A

#35320 from Super Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)

Summary

As printed in Fastrack

In STL Spec Lines, Table A, Mazda 12A, change Notes as follows:
"The 5th and 6th intake port actuators and valves may be removed or disabled."

2024-05-01 P2 CN Spec ECU

#35835 from Bart Wolf · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line E, change the notes as follows:
"No engine modifications except for dry sump oil system, ECU mapping, and exhaust system the following: oil system, ECU, and
exhaust are unrestricted."

2024-05-01 P2 E&O - Correct FIA Group CN spec line notes

#35900 from Club Racing Board · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, FIA Group CN spec line, change the notes as follows:
"FIA Group CN homologated chassis, brake calipers and discs, hub carriers, and suspension components are required. V de
V European Proto Endurance Series Challenge permitted bodywork, rear diffuser, wing, wheels, and assisted
shifting are allowed. Car M must comply with all other P2 requirements. Competitors must have copies of FIA Group CN
Technical Regulations and V de V European Proto Endurance Series Challenge Sporting and Technical Regulations in their
possession and present them upon request are available here: https://www.scca.com/pages/technical-forms-and-downloads."

2024-12-01 STL Request to Remove Miata Hubs from General category

#37138 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.M.18., change as follows:
"18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda
Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."

2024-12-01 P2 2000 cc Pinto Engine Car Weight

#37187 from Marvin Hodges · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Line E Note 2, add the following:
"8. Minimum weight 1335 lbs."

2025-02-01 FA Classify FR European Championship car as spec line car in Table 2

#37658 from Club Racing Board · Rule change · TB 25-02 (2025-02 Fastrack)

Summary

As printed in Fastrack

In FA Table 2, add the following:
Table 2 (Spec Line Cars)
Car Engine
Wheel
Width (in)
± .060
Aero Transmission Weight Notes

A specification table follows in the original; it is not shown here.

2025-03-01 FA Update Formula Renault 2.0 spec line notes

#37853 from Club Racing Board · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In FA Table 2, Formula Renault 2.0 (10-17) spec line, change the notes as follows:
"Engine must remain sealed. Car must comply with year-specific Formula Renault 2.0 manual, technical regulations, and all
applicable bulletins found here:. Competitors must have copies of these materials in their possession and present them upon
request.
https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/bulletins-techniques/2017,
https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/manuel-d-utilisateur/2017.
The following exceptions apply: Tire choice is unrestricted. No part of the car may be altered from original Formula Renault 2.0
components, except for necessary repairs that do not affect performance."

2025-05-01 STL E&O: SMX Allowance in STL

#37945 from Greg Amy · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

As printed in Fastrack

In STL Spec Lines, Table B, Mazda Spec MX5 Challenge, change as follows:
Minimum Weight: "2500 See 9.1.7.1."
Notes: "Mazda MX5 Challenge car must utilize the following components: Roush CNC cylinder head 0000-01-5300,Mahle
standard or +0.005 0000-01-5310, OEM camshaft, 11:1 compression ratio, header 0000-06-5407-NC, exhaust 0000-06-5427-NC,
cold air intake 0000- 06-5150-KT, ECU flash 0000-01-5379, Pagid front brake pads 0000-03-5104-SP or endurance pads 0000-03-
5104-EN, Pagid rear brake pads 0000-03-5114-SP or endurance pads 0000-03-5114-EN, Penske front shock 0000-04-5291-SA,
Penske rear shock 0000-04-5292-SA, Penske rear mount kit 0000-04-5358, Front mount kit 0000-04-5359, Front offset bushing
0000-04-5407-NC, Eibach front springs 0000-04-9700-08, Eibach rear springs 0000-04-9400-07, Eibach helper springs 0000-04-

Applies to Mazda Miata on this page: Jared Korth, Ricardo Arruda, Gavin Wardle, Ryan Gutile, Bryce Johnson, Andy Chittum, Adrian Comstock

2025-07-01 FA Ligier JS F3 Tire Choice

#38434 from Rocco Magni · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

As printed in Fastrack

In FA Table 2, FR Americas Ligier JS F3 spec line, change the notes as follows:
"Engine must be sealed in compliance with FR Americas or prior F3 Americas requirements. Car must comply with FR Americas
rules, with the following exception: front tires may be Hoosier P/N 43363, size 240/580R13 in MS compound, and rear tires may
be Hoosier P/N 43368, size 300/590R13 in MS compound. Competitors must have current copies of Formula Regional Americas
Championship Sporting Regulations, Onroak Automotive Ligier JS F3 Information Manual, and HPD engine-related specifications
and instructions in their possession and present them upon request."

2025-08-01 STL Lotus Weight Reduction

#38772 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)

Summary

As printed in Fastrack

In 9.1.2. GT2/ST Spec Lines, Lotus Evora GT4, change Weight as follows:
"2750 2700"
In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows:
Lotus Elise Cup R: "2300 2250"
Lotus Elise SC/ Lotus Exige SC: "2300 2550
2500 2450"

2025-11-01 FA Re-Consider USF Pro 2000 Car for Formula Atlantic Class

#38783 from Augie Pabst · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

As printed in Fastrack

Effective 11/1/25 in FA Table 2, add the following:

2026-01-01 FA Alternate Intake Manifold for MZR

#38223 from Ove Olsson · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In FA, GCR section 9.1.1.2.d, modify as follows:
"9. Intake manifold must be unmodified Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT, 1.882” maximum bore
diameter at throttle plates. Elan or Mazda Speed equivalent Elite intake manifold may be replaced with unmodified intake Noor
P/N 0088-8-00 with intake runners AT Power P/N 13624."
"10. Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT intake manifold must use an A aluminum spacer must be
used between the intake manifold and cylinder head castings; minimum spacer length is 2.200”."

2026-01-01 FA Engine Compression Rule Change Request

#39302 from Reilly Harris · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In FA Table 2, Formula 1000 spec line, change the Engine as follows:
"Motorcycle-based 4-cycle up to 1000cc, maximum compression ratio 14.5:1;. o Otherwise, current FA engine rules apply."

2026-01-01 STL Weight adjustment for STL

#39579 from Super Touring Committee · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.2.H.1. change Minimum Weight on chart as follows:

A specification table follows in the original; it is not shown here.

2026-01-01 FA Change Formula 1000 allowances

#39608 from Club Racing Board · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In FA Table 2, Formula 1000 spec line, change the Notes as follows:
"Car must comply with December 2019 GCR Formula 1000 (FB) Preparation Rules, https://www.scca.com/downloads/48184-
gcr-december-2019/download, except as modified by this spec line. The prohibition of using carbon fiber in any external panels
or any panels licked by the airstream in Part 3.C of the December 2019 GCR F1000 (FB) Preparation Rules is removed, with the
exception that the car's floor pan/undertray must comply with the requirements of Part 2.D of the December 2019 GCR F1000
(FB) Preparation Rules. The prohibition of forward-facing gaps or openings in the bodywork in Part 3.I of the December 2019 GCR
F1000 (FB) Preparation Rules is removed. Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is modified as
follows: "Between the rear of the front tire and the front of the rear tire, no point on the lower surface of the car (the surface

2026-02-01 FA Pro Mazda Classification and Performance Enhancement Proposal

#39411 from Stephen Lamana · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

As printed in Fastrack

In FA Table 2, Pro Formula Mazda spec line, change the notes as follows:
"All current FA rules apply to areas not covered by this spec line. Apex seals unrestricted. Street port or bridge port
allowed. Unmodified OEM l Lower intake manifold required unrestricted, upper intake manifold unrestricted. Balance tube not
permitted. Fuel injection only. Maximum 70 80mm T throttle B body. The maximum height of the wing and/or
endplates shall must not exceed 99cm (38.98 inches). The overall maximum width of the bodywork behind the front
wheels shall must not exceed 132cm (51.97 inches)."