STU + P2 + FC at Buttonwillow Raceway Park

2023-03-01 STU E&O STU NA Weight Chart.

#33737 from Eric Heinrich · Rule change · TB 23-03 (2023-03 Fastrack)

Summary

As printed in Fastrack

In STU, GCR Section 9.1.4.1.H.1. chart, Factory Engine Displacement (cc) Minimum Weight (lbs), change as follows:
"2450 2596 2595"
"2600 2860 2710"

2023-04-01 STU Alternate OEM Miata Intake Manifold

#33827 from Brandon Steinhauer · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In STU Spec lines, classify Mazda BP5A as follows:
STU Maximum Displacement (cc's) Minimum Weight Notes
Mazda BP5A 1839 Chart May use engine in its entirety or specific
components from the engine.

2023-04-01 P2 Remove redundant effective date language and update engine table

#34012 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, change as follows:

2023-04-01 P2 E&O - Correct dimensional equivalents

#34038 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.2, change as follows:
"Height: No part of the vehicle having special or significant aerodynamic function shall exceed a height of 115cm (45.275 inches)
above the ground with the car in normal racing trim, driver aboard."
In P2, GCR section 9.1.8.C.D.3, change as follows:
"However, no portion shall extend more than 10cm (3.937 inches) beyond a plane tangent to the outer face of the front and rear
wheels with tires."
P2 Engine Table
Spec

A specification table follows in the original; it is not shown here.

2023-05-01 P2 Clarify minimum side body height requirement

#34143 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.6, change as follows:
"As viewed from the side, T the outermost surface of side pods body between the front and rear wheel openings and above the
floor must have a minimum height equal to the height of the front axle centerline."

2023-05-01 P2 Clarify closed cockpit single seat car allowance

#34144 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.C, add a section as follows:
"4. Closed cockpit single seat cars are not permitted unless specifically allowed by a spec line in Table 1."

2023-06-01 FC USF2000 Van Diemen with Mazda MZR LF-DE 2.0L in FC

#34329 from Formula/Sports Racing Committee · Rule change · TB 23-06 (2023-06 Fastrack)

Summary

As printed in Fastrack

RM 23-07, USF2000 Van Diemen with Mazda MZR LF-DE 2.0L in FC, GCR section 9.1.1.B.1, add a new section and re-letter the
following sections accordingly:
"c. The USF2000 tube frame Van Diemen car powered by the Mazda MZR LF-DE 2 liter engine is added as a "spec line" car in
Formula Continental. Additional "spec line" cars are disfavored, and Balance of Performance (BoP) adjustments to keep "spec
line" cars competitive with cars that meet the class formula are likewise disfavored."
In FC, GCR section 9.1.1.B.11, add the following:
"The only permitted engines are:
a. The Ford 2 liter single overhead camshaft "NE" series engine or the 1971-74 Pinto/Capri 2 liter single overhead camshaft

A specification table follows in the original; it is not shown here.

2023-07-01 FC Review FC Runoffs Tire Marking Rule

#34274 from SCCA Staff · Rule change · TB 23-06 (2023-05 Fastrack)

Summary

As printed in Fastrack

In FC, GCR section 9.1.1.B.10.h, change as follows:
"FC shall be is permitted a maximum of four (4) dry tires and four (4) wet tires for all Regional, Major, and Super Tour events;
eight (8) dry tires and eight (8) wet tires are permitted for the Runoffs. This rule shall be is effective beginning with the first (1st)
qualifying session of the event. Marked tires are not required for testing or practice. It is the competitor's responsibility to
ensure that the tires are declared, marked, and logged by Tech in advance of the tire(s) being used in a qualifying session or
race. Failure to participate on marked tires will result in a penalty.
1. Use of an undeclared tire shall automatically result in all times being disallowed in that session or finishing position in that
race.

2023-07-01 STU 2022 Toyota GR Cup for STU

#34449 from Club Racing Board · Rule change · TB 23-06 (2023-05 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Toyota GR Cup (2022-), classify as follows:

A specification table follows in the original; it is not shown here.

2023-12-01 P2 Correct Table 1 for Engine Date Range Specifications

#35182 from Formula/Sports Racing Committee · Rule change · TB 23-12 (2023-09 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 FC Please correct omitted punctuation

#34890 from Club Racing Board · Rule change · TB 23-10 (2023-09 Fastrack)

Summary

As printed in Fastrack

In Cars and Equipment, GCR section 9.3.33.B.2, add the following:
"(Effective 1/1/2024) A red taillight meeting FIA Standard 8874-2019, Technical List No. 76, is required on all Formula (open
wheel) and Sports Racing cars."
In Appendix F. Technical Glossary, Minimum Weight, change as follows:
"Minimum Weight: – Weight specified with driver, exactly as they come off the race circuit, at the conclusion of any race or
qualifying session."
In FA Table 1, Spec Line E notes, add the following:
"Any BD series iron or alloy cylinder block and alternate crankshaft permitted."

2024-01-01 P2 E&O - Clarify B.1 modified engine range in AMAC spec lines

#35225 from Club Racing Board · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 P2 Replacement Engine Crankcase for 07/08 Suzuki GSX-R1000 Engines

#35340 from Michael A Reupert · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, add to notes as follows:
"No modifications allowed on engines manufactured after 2008 model year. 2007-2008 Suzuki GSX-R1000 crankcase part
#11300-21860 may be replaced with 2016-2019 Suzuki GSX-S1000 crankcase part #11301-04840."

2024-02-01 STU ST Electric-Assisted Steering Systems

#35066 from Jose Osiris Pena · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.M.16., change as follows:
"Power steering may be modified in any of the following ways:
a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be
modified internally to work without pump.
b. an OEM manual steering rack for that model may be fitted
c. an electric power steering pump may be fitted
d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used
e. an OEM hydraulic-assisted steering system may be used"

2024-03-01 STU Letter #35397 addendum

#35453 from Aaron Fitzsimmons · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Mini Cooper S SC with Minimum Weight 1900 and 2100, add to Notes:
"Alternate LEAP OMICRON hood scoop part # LEP-OMICRON3 is permitted."

2024-03-01 STU S54 Drysump

#35464 from Macey Urso · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, BMW S54 B32 OEM, add to Notes as follows:
"Dry Sump oiling system permitted."

2024-04-01 FC Four Pot Calipers

#35481 from Steve Jenks · Rule change · TB 24-04 (2024-04 Fastrack)

Summary

As printed in Fastrack

In FC Table FC Charts, add the following:
In FC, GCR section 9.1.1.B.1.c, change as follows:
"The USF2000 tube frame Van Diemen car powered by the Mazda MZR LF-DE 2 liter engine and the F2000 Metrik ZF2 car
equipped with 4-piston calipers is are added as a "spec line" cars in Formula Continental. Additional "spec line" cars are
disfavored, and Balance of Performance (BoP) adjustments to keep "spec line" cars competitive with cars that meet the class
formula are likewise disfavored."
FC Charts
Car Engine Wheel Width

A specification table follows in the original; it is not shown here.

2024-05-01 P2 CN Spec ECU

#35835 from Bart Wolf · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line E, change the notes as follows:
"No engine modifications except for dry sump oil system, ECU mapping, and exhaust system the following: oil system, ECU, and
exhaust are unrestricted."

2024-05-01 P2 E&O - Correct FIA Group CN spec line notes

#35900 from Club Racing Board · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, FIA Group CN spec line, change the notes as follows:
"FIA Group CN homologated chassis, brake calipers and discs, hub carriers, and suspension components are required. V de
V European Proto Endurance Series Challenge permitted bodywork, rear diffuser, wing, wheels, and assisted
shifting are allowed. Car M must comply with all other P2 requirements. Competitors must have copies of FIA Group CN
Technical Regulations and V de V European Proto Endurance Series Challenge Sporting and Technical Regulations in their
possession and present them upon request are available here: https://www.scca.com/pages/technical-forms-and-downloads."

2024-08-01 STU RWD Turbo Disadvantage

#36255 from David Fiorelli · Rule change · TB 24-08 (2024-08 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.1.H.3 - Inlet Restrictor (mm) Minimum Weight (lbs) table, change as follows:
"RWD cars must reduce restrictor 1 mm from this table"

2024-11-01 FC 9.1.1.10.h. FC Tire Rule

#36533 from SCCA Staff · Rule change · TB 24-09 (2024-09 Fastrack)

Summary

As printed in Fastrack

In FC, GCR section 9.1.1.B.10.h, change as follows:
"(Effective 11/1/2024) FC is permitted a maximum of four (4) dry tires and four (4) wet tires for all Regional, Major, and Super
Tour events; eight (8) dry tires and eight (8) wet tires are permitted for the Runoffs. This is effective beginning with the first (1st)
qualifying session of the event. Marked tires are not required for The tire limit does not apply to testing or practice. It is the
competitor's responsibility to ensure that the tires are declared, marked, and logged by Tech immediately upon conclusion of the
first qualifying session, as provided in the event supplemental regulations, or per the instructions of the Race Director or Chief
Steward. in advance of the tire(s) being used in a qualifying session or race. Failure to participate on marked Use of tires in
excess of the number allowed will result in a penalty. Failure to participate on declared/marked/logged tires after the time

2024-11-01 FC Change FF/FC Weight with Sequential Gearbox

#36651 from Robert Wright · Rule change · TB 24-11 (2024-11 Fastrack)

Summary

As printed in Fastrack

In FF, GCR section 9.1.1.B.20.A.3, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
In FC, GCR section 9.1.1.B.20.B.4, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."

2024-11-01 STU R53 15% Pulley Request

#36980 from Aaron Fitzsimmons · Rule change · TB 24-11 (2024-11 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Mini Cooper S SC, add to notes:
1900: "Stock supercharger pulley. 2.565 diameter."
2100: "JCW Pulley permitted. May run a 2.285 diameter pulley."

2024-12-01 STU Request to Remove Miata Hubs from General category

#37138 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.M.18., change as follows:
"18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda
Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."

2024-12-01 STU BMW N54/N55 Engine Allowance

#37146 from Martin Sarukhanyan · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

As printed in Fastrack

"Turbo inlet restrictors designed per GCR Appendix F Technical Glossary definition of “Turbo Inlet Restrictor” may be required;
see table 9.1.4.1.H.h.2 3. Swapping of turbochargers between engine makes and models is prohibited. Supercharged cars may be
approved on a case-by-case basis; twin turbo engines are allowed on a case-by-case basis only. Contact the Road Racing
Technical Office for details. Twin turbo engines may be converted to single turbo using one of the allowed alternate turbos (see
9.1.4.1.H.3 2). Aftermarket turbocharger and supercharger kits will be allowed on a case-by-case basis.

2024-12-01 P2 2000 cc Pinto Engine Car Weight

#37187 from Marvin Hodges · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Line E Note 2, add the following:
"8. Minimum weight 1335 lbs."

2025-01-01 STU Audi 1.8t Wagon STU Table B

#36685 from Mike McLaughlin · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Table B: Alternate Vehicle and Engine Requirements, delete Audi/VW 1.8 Turbo in its entirety.
In STU Spec Lines, Table B: Alternate Vehicle and Engine Requirements, Porsche 944 w/Max Displacement 1800, change as
follows:
Weight: "3050 Chart"
Notes: "VW/Audi 1.8L 35mm turbo engine permittedinlet restrictor required."

2025-01-01 STU Merger GT3 to STU

#37486 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In STU, Table C, change STU-GT3 charge as follows:
"(Effective January 1, 2026) TABLE C: STU-GT3U"

2025-01-01 STU GT3 TCR Tire allowance

#37494 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In STU, Table C, GT3 TCR, add to Notes the following:
"May run DOT approved tire with maximum section width of 275 with 100 pound weight adder. May not run A compound with
275."

2025-03-01 STU BMW N54/N55 Engine Allowance Follow Up

#37447 from Martin Sarukhanyan · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Table A, classify BMW N54/N55 as follows:
STU Maximum Displacement
(cc's) Minimum Weight Notes
BMW N54/N55 3.0 Chart +3% (DI) Short blocks, heads, and intakes may be
freely swapped within these engine
designations. N54 twin turbo not allowed

2025-03-01 STU STU Mini Cooper pulley size clarification re: letter #36980

#37717 from Aaron Fitzsimmons · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Mini Cooper S SC, add to notes:
2100: "May run a 2.285 2.185 diameter pulley."

2025-03-01 STU Question About a Weight Modifier

#37782 from Peter St Pierre · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Table A, Honda K20C1 Turbo I4, add to Notes the following:
"The 3% DI weight adder does not need to be applied."

2025-03-01 STU Increase Minimum Weight

#37919 from Club Racing Board · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Table C: STU-GT3U, change Minimum Weight as follows:
"150 250 pounds"

2025-05-01 STU Wheel Size Inconsistency

#38018 from David Fiorelli · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.1.F.1., change as follows:
"Wheels may not exceed 18 inches in diameter. or 8.0 inches in width for vehicles 2950 lbs. and under minimum allowed race
weight. Vehicles over 2850 minimum allowed race weight may use a 9 inch wide wheel. Cars equal to or less than 2,850 lbs.
minimum allowed race weight may not use wheels wider than 8 inches. Cars greater than 2,850 lbs. minimum allowed race
weight may not use wheels wider than 9 inches."

2025-05-01 STU Table C: STU-GT3U Clarification

#38268 from Club Racing Board · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

As printed in Fastrack

In STU Spec Line, Table C: STU-GT3U, change as follows:
Minimum Weight: “Current GT3 race weight plus 250 225 pounds”
Notes: "DOT approved tire with maximum section width of 245. GT3 cars base wheel is a maximum of 15”x9”. 18”x9” wheels
allowd with a 3% weight addition. GT3 cars utilizing 15”x7” wheels are limited to a maximum section width of 225 with a 25
pound weight reduction"
"All GT3U (Majors and Runoffs) cars using up to 15"x7" wheels limited to 225 section width tires shall run at current GT3 race
weight plus 225lbs. All Gt3U cars shall run a DOT approved tire with a maximum section width of 245. GT3U cars are allowed
optional 15"x9" wheels with a 1.5% weight addition or up to 18"x9" wheels with a 3.0% weight addition to the total weight

2025-07-01 STU 2.8-3.2L N/A Engine Allowances

#38007 from Ben Slechta · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.G.1, add the following:
"A maximum section width of 245 is permitted. Cars over 3150 lbs. may run a 275 tire with a 2% weight adder."

2025-07-01 STU 2006-2015 Mazda Miata Intake Manifold

#38422 from German Candelario Candelario · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

As printed in Fastrack

In STU, Table A, Mazda MZR (LF, L3, L5), change Notes as follows:
"May use Goodwin Part # 61-2510 or Gato Performance Part #31972 Intake manifold . "

2025-07-01 STU Requesting Approval of the JDM Honda h23a

#38489 from Eric Fiest · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

As printed in Fastrack

In STU, Table B, classify Honda JDM H23a as follows:
STU Maximum Displacement (cc's) Minimum Weight Notes
Honda JDM H23a 2259 Chart Must meet all ST engine regulations.

2025-08-01 STU STU-TCR Adjustments

#38723 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Table C: STU-GT3U, GT3-TCR, change as follows: Remove the current TCR spec line and add the TCR spec lines
from GT3 that are being removed, adding the below to the notes.
"DOT approved tire with maximum section width of 245. May run DOT approved tire with maximum section width of 275 with
100 150 pound weight adder. May not run A-compound with 275. STU-TCR spitters and side valance must comply with
9.1.4.D.3.f. STU-TCR chassis ride height must comply with 9.1.4.1.A.1."

2025-08-01 STU Lotus Weight Reduction

#38772 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)

Summary

As printed in Fastrack

In 9.1.2. GT2/ST Spec Lines, Lotus Evora GT4, change Weight as follows:
"2750 2700"
In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows:
Lotus Elise Cup R: "2300 2250"
Lotus Elise SC/ Lotus Exige SC: "2300 2550
2500 2450"

2025-09-01 STU Lotus Weight Reduction E&O

#38919 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

As printed in Fastrack

In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows:
Lotus Elise SC/ Lotus Exige SC: "2450 2250"

2025-11-01 STU Non-Homologated Engine Swaps - Specifically K24A2 w/ Honda CRZ

#38746 from William Rori · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Table B: Alternate Vehicle and Engine Allowances, Honda K24, change Weight as follows:
"(Effective 11/1/2025) Chart + 2%"

2025-12-01 STU Turbo Inlet Restrictor Table

#38961 from John Weisberg · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.H.3, change chart as follows:

A specification table follows in the original; it is not shown here.

2025-12-01 STU 275 Tire Rule

#38983 from Peter Federlin · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.4.G.1., change as follows:
"A maximum section width of 245 is permitted. Cars over 3150 lbs. may run a 275 tire with a 2% weight adder."

2025-12-01 STU STU Honda Engine weight penalty

#39375 from Super Touring Committee · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Minimum Weight as follows:
Honda K20: "Chart + 2%"
Honda K24: "Chart + 2%"

2026-01-01 FC F2000 MZR Spec Line Clarity/Revision Requested

#38927 from Rock Beauchamp · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In FC Charts table, USF2000 Tube Frame spec line, add the following to the Notes:
"Cars originally built with the Hewland LD200 4-speed H-pattern may use that transmission as an alternative to the Hewland JL-
200 5-speed sequential transmission."

2026-01-01 STU Request for Permission on Aftermarket Turbo Kit and Intake

#39529 from John Grim · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In STU Spec Lines, Table A: Alternate Vehicle and Engine Allowances, Mazda MZR (LF, L3, L5), change Notes as follows:
"Short blocks, heads, and intakes may be freely swapped within these engine designations. May use Goodwin Part # 61-
2510 or, Gato Performance Part #31972 or Jack Spania Racing 70 mm sheet-metal aluminum Intake manifold. Must use stock
throttle body or Acura part number 16400-PND-A17."
In STU Spec Lines, Table A: Alternate Vehicle and Engine Allowances, classify Mazda MZR (LF, L3, L5) Turbo as follows:
STU Maximum Displacement (cc's) Minimum Weight Notes
Mazda MZR (LF, L3,
L5) Turbo

2026-01-01 FC Adjust F2000 Metrik ZF2 weight

#39612 from Club Racing Board · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In FC Charts table, F2000 Metrik ZF2 spec line, change the Weight as follows:
"1240 1220"