BoP Lab / Buttonwillow Raceway Park

FA + FE2 + AS at Buttonwillow Raceway Park

No mapCal Club 2024, Cal Club 2023

This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.

5 laps are left out as timing errors (far too short to be a lap of this track). The rest of those sessions, sectors included, is used.

Pos	Car	Driver	Class	#	Lap	Theoretical	Qual	Race	5-lap stint	Consistency	Trap	S1	S2	S3
1	Formula Enterprise (2023)	Blake Pigeon	FE2	108	1:12.402 D-Q2		1:12.402 D-Q2
2	SCCA Ent FE2 (2007)	John Yeatman	FE2	22	1:13.988 D-Q2		1:13.988 D-Q2
3	SCCA Ent FE2 (2010)	Thomas W Burt	FE2	45	1:14.003 D-Q2		1:14.003 D-Q2
4	Pro Formula Mazda (2013)	Greg Labadie 2+ cars	FA	35	1:14.588 D-Q2		1:14.588 D-Q2
5	Swift 016	Greg Labadie 2+ cars >115%	FA	35	1:35.792 A-Q1	1:35.351	1:35.792 A-Q1	1:37.275 A-R1	1:37.692 A-R1	+3.958 A-R1	163.8 A-R1	26.713 A-Q2	26.816 A-Q1	41.822 A-Q1
6	SCCA Ent FE2	Jon McClintock >115%	FE2	23	1:39.265 A-Q2	1:39.265	1:39.265 A-Q2	1:40.253 A-R1	1:40.602 A-R1	+1.377 A-R1	152.6 A-Q2	27.464 A-Q2	28.773 A-Q2	43.028 A-Q2
7	SCCA Ent FE2	Paul Marino >115%	FE2	44	1:39.358 B-Q2	1:39.209	1:39.358 B-Q2	1:39.712 B-R1	1:40.188 B-R1	+0.849 B-R1	156.6 A-Q1	27.234 B-Q2	28.582 B-R1	43.393 B-Q2
8	SCCA Ent FE2	Tom Hope >115%	FE2	18	1:39.452 B-Q2	1:39.393	1:39.452 B-Q2	1:39.992 B-R1	1:40.186 B-R1	+0.531 B-R1	125.6 B-Q1	27.375 B-Q2	28.661 B-Q2	43.357 B-Q1
9	SCCA Ent FE2	Tom Burt >115%	FE2	45	1:40.774 B-Q1	1:40.569	1:40.774 B-Q1	1:40.955 B-R1	1:41.516 B-R1	+0.989 B-R1	154.7 A-R1	27.836 B-R1	29.021 A-Q2	43.712 B-Q1
10	SCCA Ent FE2	Noah Hambayi >115%	FE2	64	1:40.848 B-Q2	1:40.673	1:40.848 B-Q2	1:41.416 B-R2	1:41.703 B-R2	+1.034 B-R2	142.4 B-P	27.646 B-R2	28.966 B-Q2	44.061 B-P
11	Ford Mustang	Roger Eagleton	AS	11	1:55.849 B-R1	1:55.569	1:56.445 B-Q1	1:55.849 B-R1	1:56.324 B-R1	+0.678 B-R1	108.7 B-R1	31.659 B-Q1	33.571 B-R1	50.339 B-R1
12	Ford Mustang	Ross Murray	AS	14, 74	1:56.314 A-R1	1:56.047	1:56.812 A-Q1	1:56.314 A-R1	1:56.660 A-R1	+0.887 A-R1	135.2 A-R2	32.070 A-R1	33.689 A-R1	50.288 A-R1
13	Ford Mustang FR500S	Pratt Cole	AS	8, 8x	1:58.795 B-R1	1:58.078	1:59.911 B-Q1	1:58.795 B-R1	1:59.396 B-R1	+1.547 B-R1	103.3 B-Q1	32.531 B-R1	33.997 B-R1	51.550 B-R1
14	Ford Mustang	Matt Lituchy	AS	30	1:59.134 B-R1	1:58.732	2:00.395 B-Q1	1:59.134 B-R1	1:59.643 B-R1	+0.914 B-R1	105.1 B-Q1	32.777 B-R1	34.259 B-R1	51.696 B-R2
15	Ford Mustang	Michael Lowe	AS	10	2:00.612 A-R2	2:00.126	2:03.053 A-Q1	2:00.612 A-R2	2:02.546 A-R2	+4.568 A-R2	126.5 A-R1	32.652 B-R1	34.913 B-R1	52.561 A-R2

One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it. Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.

Sectors

S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi

Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.

By car

Car	Class	Drivers	Lap	Qual	Race	Trap	S1	S2	S3
Formula Enterprise	FE2	1	1:12.402Blake Pigeon	1:12.402Blake Pigeon
SCCA Ent FE2	FE2	7	1:13.988John Yeatman	1:13.988John Yeatman	1:39.712Paul Marino	156.6Paul Marino	27.234Paul Marino	28.582Paul Marino	43.028Jon McClintock
SCCA Ent FE2 (2007)	FE2	1	1:13.988John Yeatman	1:13.988John Yeatman
SCCA Ent FE2 (2010)	FE2	1	1:14.003Thomas W Burt	1:14.003Thomas W Burt
SCCA Ent FE2	FE2	5	1:39.265Jon McClintock	1:39.265Jon McClintock	1:39.712Paul Marino	156.6Paul Marino	27.234Paul Marino	28.582Paul Marino	43.028Jon McClintock
Pro Formula Mazda	FA	1	1:14.588Greg Labadie	1:14.588Greg Labadie
Swift 016	FA	1	1:35.792Greg Labadie	1:35.792Greg Labadie	1:37.275Greg Labadie	163.8Greg Labadie	26.713Greg Labadie	26.816Greg Labadie	41.822Greg Labadie
Ford Mustang	AS	5	1:55.849Roger Eagleton	1:56.445Roger Eagleton	1:55.849Roger Eagleton	135.2Ross Murray	31.659Roger Eagleton	33.571Roger Eagleton	50.288Ross Murray
Ford Mustang	AS	4	1:55.849Roger Eagleton	1:56.445Roger Eagleton	1:55.849Roger Eagleton	135.2Ross Murray	31.659Roger Eagleton	33.571Roger Eagleton	50.288Ross Murray
Ford Mustang FR500S	AS	1	1:58.795Pratt Cole	1:59.911Pratt Cole	1:58.795Pratt Cole	103.3Pratt Cole	32.531Pratt Cole	33.997Pratt Cole	51.550Pratt Cole

The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.

Rule changes between these events

Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23

2023-05-01 FA E&O - Correct Pro Formula Mazda spec line dimensional equivalent

#34085 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

fasterFA Pro Formula Mazda maximum bodywork width behind front wheels increases to 51.97 inches.

As printed in Fastrack

In FA Table 2, Pro Formula Mazda spec line, change as follows:
"The overall maximum width of the bodywork behind the front wheels shall not exceed 132cm (~~51.17~~ 51.97 inches)."

2023-05-01 FA Add new spec line for MSR Formula Mazda FMzR to Table 2

#34139 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

cars addedFA MSR Formula Mazda FMzR added to Table 2 classification.

As printed in Fastrack

RM 23-06 – MSR - FMzR Formula Atlantic Classification dated 4/21/2023
In FA Table 2, add a spec line as follows:

2023-06-01 FA Simplify Pro Formula Mazda wheel allowance

#34190 from Club Racing Board · Rule change · TB 23-06 (2023-06 Fastrack)

Summary

unclearFA Pro Formula Mazda front wheels widen to 10 in. max; rear wheels narrow to 14 in. min.

As printed in Fastrack

In FA, Pro Formula Mazda spec line, change wheel width as follows:
"~~Pro Mazda series wheels~~

A specification table follows in the original; it is not shown here.

2023-08-01 AS Crate Motor Part Numbers

#32944 from Sam Daniels · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

wordingAS crate motor part number specified: GM Performance CT400 P/N 19370604 engine assembly for GM vehicles.

As printed in Fastrack

In AS, GCR Section 9.1.6.F.2., change as follows:
"GM Performance parts CT400 P/N-1937 → 0604 or 1937 → 0604 engine assembly for GM produced vehicles."

2023-08-01 AS Request wheel size change

#33007 from Michael Kamalian · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

fasterAS Spec Lines Ford Mustang GT 5.0L (15-17) max wheel size increases to 19.0 inches.

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT 5.0l (15-17) Restricted Preparation, change Notes as follows:
"Max. Wheel Size: Dia.~~18.0~~ 19.0 inches."

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2023-08-01 AS Alternative Upper Front Control Arms for Dodge Challenger

#33352 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

wordingAS Dodge Challenger 5.7L/6.1L/6.4L V8 now permits SPC-66045 alternate front upper control arms.

As printed in Fastrack

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"~~SPC-66045~~ Alternate front upper control arms are permitted."

2023-08-01 AS Front Brake Caliper Adapters for Dodge Challenger

#33353 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

wordingAS Dodge Challenger 5.7L/6.1L/6.4L V8 allows alternate front brake caliper adapters for updated or backdated components.

As printed in Fastrack

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"Stock brakes or alternate Dodge brakes (Part numbers: front caliper (0517 → 5106 (R) and 0517 → 5107 (L); rear caliper (R1542564 (R)
and R1542565 (L))) may be used with the brake rotor sizes listed in this specification line. Alternate brackets may be used to
facilitate updated/backdated components."

Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22

2024-03-01 AS Request to Classify 1970-1981 Camaro and Firebird in AS

#33659 from Brandon Vivian · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

cars addedChevrolet Camaro, Pontiac Firebird 70-81 Full Prep classified AS at 3400-3600 lbs with 250 lb weight reduction.

As printed in Fastrack

In AS Spec Lines, classify Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep as follows:
AS Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:

A specification table follows in the original; it is not shown here.

2024-03-01 AS Fuel Cell 12

#34194 from Clark Cambern · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

wordingAS class: multiple cars gain fuel cell placement note allowing 24 inches from standard tank, unrestricted filler location.

As printed in Fastrack

In AS Spec Lines, add to Notes as follows:
Cadillac CTS-V (04-07): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken
from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24
inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with

Show 22 more lines

installation of a safety fuel cell.”
Chevrolet Camaro SS (V8) (10-15): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Chevrolet Camaro (10-15): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Dodge Challenger (08-20): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Ford Mustang GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Ford Mustang Coupe GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Ford Mustang GT 5.0l (15-17): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement
is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Ford Mustang GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”

2024-03-01 AS Please Classify the 6th Gen Into AS.

#35448 from Daniel Richardson · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

cars addedChevrolet Camaro 16- Full Prep classified into AS at 3400 lbs with 250 lb weight reduction.

As printed in Fastrack

In AS Spec Lines, classify Chevrolet Camaro (16-) Full Prep as follows:
AS
Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:

Show 4 more lines

Chevrolet
Camaro (16-)
Full Prep
110.6 3.42, 2.28,

A specification table follows in the original; it is not shown here.

2024-03-01 AS spec lines

#35713 from American Sedan Committee · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

cars addedAS adds Ford Mustang GT 05-14 Restricted prep Engine with 62mm FPR, 3400 lbs minimum, 18-inch wheels.

As printed in Fastrack

In AS Spec Lines, classify Ford Mustang GT (05-14) with Restricted prep Engine as follows:
AS
Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2024-04-01 AS Restricted Prep Aftermarket Parts Request

#35682 from Tom Aquilante · Rule change · TB 24-04 (2024-04 Fastrack)

Summary

wordingAS Camaro/Firebird and GTO LS1 connecting rods approved: Callies CSC6100DS6A2AH, Scat 2-1CR6100-944, GM 12649190.

As printed in Fastrack

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."
In AS Spec Lines, Pontiac GTO (04-06), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."

2024-04-01 AS Allowance of 11

#35824 from American Sedan Committee · Rule change · TB 24-04 (2024-04 Fastrack)

Summary

fasterAS Cadillac CTS-V, Chevrolet Camaro SS, Dodge Challenger, Ford Mustang GT, Pontiac GTO allowed 11" wheels until 3/1/25.

As printed in Fastrack

In AS Spec Lines, Cadillac CTS-V (04-07), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Chevrolet Camaro SS (V8) (10-15), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Dodge Challenger (08-20), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Ford Mustang GT 5.0l (15-17), add to Notes the following:
"11" wide wheels can be used until 3/1/25."

Show 2 more lines

In AS Spec Lines, Pontiac GTO (04-06), add to Notes the following:
"11" wide wheels can be used until 3/1/25."

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2024-05-01 AS 6th gen Camaro limited prep

#35733 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

cars addedAS Chevrolet Camaro 1LE (2016-) classified with 3600 lbs minimum weight, 60mm restrictor, 275 tires.

As printed in Fastrack

In AS Spec Lines, classify Chevrolet Camaro 1LE (2016-) as follows:
AS Wheelbase Gear Ratios Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs.) Notes:
Chevrolet
Camaro, 1LE

Show 2 more lines

(2016-)
110.6 2.66,1.78,1.30,0.74,.5 (F)

A specification table follows in the original; it is not shown here.

2024-05-01 AS Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V8 LS1 Alum BLK

#35825 from Desi Colon · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

cars addedAS Chevrolet/Pontiac Camaro & Firebird 82-92 5.7L LS1 classified at 3200 lbs with 65mm restrictor plate required.

As printed in Fastrack

In AS Spec Lines, classify Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves
per cylinder, as follows:
AS Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

2024-05-01 AS Full Prep Head

#35891 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

otherAS Chevrolet Camaro, Firebird, and Ford Mustang models permitted to use Flo Tek cylinder heads.

As printed in Fastrack

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (82-92), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet Camaro (10-15), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86), add to Notes the following:
"Flo Tek Part # 203-500 are permitted."

Show 4 more lines

In AS Spec Lines, Ford Mustang Including Cobra 94-04, add to Notes the following:
"Flo Tek Part # 203-500 are permitted."
In AS Spec Lines, Ford Mustang GT (05-14), add to Notes the following:
"Flo Tek Part # 203-500 are permitted."

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2024-06-01 AS Request for Classification of 2018-2023 mustang In

#35764 from Michael Kamalian · Rule change · TB 24-06 (2024-06 Fastrack)

Summary

cars addedAS Ford Mustang GT 5.0L (2018-) classified at 3600 lbs with 60mm restrictor, Brembo BBK permitted.

As printed in Fastrack

AS Spec Lines, classify Ford Mustang GT 5.0L (2018-) as follows:
AS Wheelbase Gear Ratios

A specification table follows in the original; it is not shown here.

2024-09-01 AS Mustang transmission ratios

#36662 from American Sedan Committee · Rule change · TB 24-09 (2024-09 Fastrack)

Summary

unclearAS Ford Mustang GT models gain alternate transmission ratio options for 2024-09-01.

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Notes as follows:
"Alternate transmission Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68.”
In AS Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows:
"Alternate transmission Ratios 3.24, 2.10, 1.42, 1.00, 0.81, .062."

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2025-01-01 AS Increase Coyote Engine Restrictor to 80mm

#36177 from Gregory Eaton · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

fasterAS Ford Mustang Coyote engines increase restrictor to 80mm from 64mm or 67mm.

As printed in Fastrack

In AS Spec Lines, add to Notes as follows:
Ford mustang (GT 05-14): "Gen 1- 67mm Gen 2-64mm"
Ford mustang (GT 05-14): "Gen 1- 67mm"
Ford mustang (GT 15-17): "Gen 1- 67mm"
Ford mustang (GT 94-04): "Gen 1- 67mm Gen 2-64mm"
Ford mustang cobra & Cobra R Mercury Capri (79-93) (79-86): "Gen 1- 67mm Gen 2-64mm"

2025-01-01 AS Performance Pack for 2015+ Mustang

#36867 from Michael Kamalian · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

fasterAS Mustang GT 05-14 4.6L loses 300 lbs; 15-17 and 2018+ models lose 61mm and 60mm restrictors respectively.

As printed in Fastrack

In AS Spec Lines, Ford Mustang Coupe GT (05-14) Restricted Prep., change Notes as follows:
"The 4.6L engine assembly has a weight reduction of 300 lbs. 5.0L/6spd engine/trans: track pack front and rear spoiler allowed."
In AS Spec Lines, Ford Mustang Coupe GT (05-14) with Restricted Prep. engine, change Notes as follows:
"Max. Wheel Size: Dia.18.0 inches. Stock brakes or alternate Ford 14” Brembo Brake (Ford Racing Kit #M-2300-S) and full prep
brake package may be used. Either engine may be used. ~~1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l~~
~~Coyote 15-17 61mm FPR~~ Cold Air Intake allowed Charge Motion Control Valves can be blocked off and removed for firewall
clearance Allow Cold Air Intake Tremec Magnum transmission may be used P/N- TUKT16901. Full Prep Transmissions rule
package may also be used. Max compression ratio, 11.2:1 track pack front and rear spoiler allowed. Alternate transmission

Show 10 more lines

Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68."
In AS Spec Lines, Ford Mustang GT 5.0l (15-17) Restricted Preparation, change Notes as follows:
"Max. Wheel Size: Dia. 18.0 inches. Stock brakes or alternate Ford Brembo Brake caliper (Ford Racing Kit #M-2300-S) may be
used. ~~61mm flat plate restrictor required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch~~
~~measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation~~
~~of a safety fuel cell~~. 11” wide wheels can be used until 3/1/25. Performance pack front and rear spoiler, body kit allowed."
In AS Spec Lines, Ford Mustang GT 5.0L (2018-), change Notes as follows:
"Package Brembo front BBK and 380mm rotors permitted (Ford PN M-2300-V) at no weight penalty. ~~60mm flat plate restrictor~~
~~required.~~ 2014 Mustang GT exhaust manifolds permitted. Ford Racing oil pan #M-6675-M50BR permitted. ~~Alternate~~
~~transmission Ratios 3.24, 2.10, 1.42, 1.00, 0.81, .062.~~ Performance pack front and rear spoiler, body kit allowed."

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2025-01-01 AS Gear Ratios

#37131 from Timothy White · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

wordingAS class gear ratio options specified for multiple American muscle cars, including Cadillac CTS-V, Chevrolet Camaro, Ford Mustang, Dodge Challenger, and Pontiac GTO.

As printed in Fastrack

In AS Spec Lines, change Gear Ratios as follows:
Cadillac CTS-V (04-07):
"2.97, 2.07, 1.43,1.00, 0.84,0.56 or 3.01, 2.07, 1.43, 1.0, .84, .57 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Full Prep:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Restricted Prep.:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet/Pontiac Camaro & Firebird (82-92) Full Prep:

Show 42 more lines

"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33,
1.00"
Chevrolet/Pontiac Camaro & Firebird (93-02) Full Prep:
"3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00,0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00,
0.68 or 2.20,1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81"
Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted prep:
"2.97, 2.07, 1.43, 1.00, 0.80, 0.62 or 3.36, 2.07, 1.35, 1.00, .80, .62 or 2.66, 1.78, 1.30, 1.00, 0.74, 0.50 or 2.88, 1.91, 1.33, 1.00 or
2.20, 1.64,1.28,1.00"
Chevrolet Camaro SS (V8) (10-15) Restricted Prep:
"3.01, 2.07, 1.43, 1.0, .84, .57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Chevrolet Camaro (10-15) Full Prep:
"3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00, 0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00,
0.68 or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81"
Chevrolet Camaro (16-) Full Prep:
"3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00, 0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00,
0.68 or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81"
Chevrolet Camaro, 1LE (16-):
"2.66,1.78,1.30, 0.74,.50 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2 valves/cylinder:
"2.97, 2.1, 1.46, 1.00, 0.74, 0.50 or 2.26, 1.58, 1.19, 1.00, 0.77, 0.63 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) Full Prep:
"3.07, 1.72, 1.00, 0.70 or 2.95, 1.94, 1.34, 1.00, 0.63 or 3.35, 1.99, 1.33, 1.00, 0.68 or 2.87 1.89 1.28 1.00 0.81"
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) with Restricted Prep Engine:
"2.95, 1.94, 1.34,1.00, 0.63 or 3.35,1.99,1.33, 1.00, 0.69 or 2.88, 1.91, 1.33, 1.00 or 3.27,1.98, 1.34, 1.00, 0.68, 3.66, 2.43, 1.69,
1.32, 1.00, .68. or 2.87,1.89,1.28,1.00,.81"
Ford Mustang Including Cobra 94-04 Full Prep:
"3.07, 1.72, 1.00, 0.70 or 2.95, 1.94, 1.34, 1.00, 0.63 or 3.35, 1.99, 1.33, 1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34,
1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 or 2.20, 1.64,1.28,1.00 or 2.87 1.89 1.28 1.00 0.81"
Ford Mustang Cobra and GT 94-95 (Restricted Prep):
"3.35, 1.99, 1.33, 1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang including Cobra 96-04 (Restricted Prep) 4.6L two and four valve motor:
"3.35, 1.99, 1.33, 1.00, 0.68 or 3.27, 1.98, 1.34, 1.00, 0.67 or 3.37, 1.99, 1.33, 1.00, 0.68 or 3.38, 2.00, 1.32, 1.00, 0.68 or 2.88,
1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang GT (05-14) Full Prep:
"3.38, 2.00, 1.32, 1.00, 0.68 or 3.66, 2.43, 1.69,1.32, 1.00, 0.65 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang GT 5.0l (15-17) Restricted Preparation:
"3.66, 2.43, 1.69,1.32, 1.00, .65 or 4.69, 2.98,2.14, 1.76,1.52, 1.27,1.00, 0.85, 0.68, 0.63, or 3.24, 2.10, 1.42, 1.00, 0.81, .062. or
2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang GT 5.0L (2018-) Restricted Preparation:
"2.97, 2.07, 1.43, 1.00, 0.84, 0.57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Pontiac GTO (04-06) Restricted Prep.
"2.97, 2.07, 1.43, 1.00, 0.84, 0.57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"

2025-01-01 AS ECU specs for LS engine

#37208 from Gary Mathews · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

fasterAS LS-engine cars gain ECU freedom; Camaro/Firebird 93-02 LS1 removes fuel cell location restriction.

As printed in Fastrack

In AS SPEC LINES, Cadillac CTS-V (04-07) Restricted Prep., change Notes as follows:
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Tremec TR6060
Transmission with 3.0 1, 2.07, 1.43, 1.0, .84, .57 ratios permitted. 11” wide wheels can be used until 3/1/25. Any ECM may be
used."
In AS SPEC LINES, Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep ., add to Notes as follows:
"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1, add to Notes as follows:

Show 14 more lines

"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep.5.7L V-8 LT1, add to Notes as follows:
"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep. 5.7L V-8 LT1; 98-02 , change Notes as follows:
"5.7L LS1:
GM Performance Parts camshaft Kit P/N-19355738 is permitted. Cylinder Bore, 99 mm; Stroke, 92 mm; Intake Valve Diameter,
50.8; Exhaust Valve Diameter, 39.4 mm; Throttle Body Bore, 75 mm; SLP Intake Lid (SLP part number 21044 (98-99) and 21045
(00-02)) is permitted.
~~Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the~~
~~stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.~~
1-3/4 headers allowed. For the LS1connecting rods Callies P/NCSC6100DS6A2AH, Scat rods P/N2-1CR6100-944, GM performance
rods P/N12649190. Any ECM may be used."
In AS SPEC LINES, Chevrolet Camaro SS (V8) (10-15) Restricted Prep., add to Notes as follows:
"Any ECM may be used."

2025-02-01 FA Classify FR European Championship car as spec line car in Table 2

#37658 from Club Racing Board · Rule change · TB 25-02 (2025-02 Fastrack)

Summary

cars addedFA adds Tatuus F.3 T-318 or FR-19 as spec line car in Table 2 for Formula Regional European Championship.

As printed in Fastrack

In FA Table 2, add the following:
Table 2 (Spec Line Cars)
Car Engine
Wheel
Width (in)
± .060
Aero Transmission Weight Notes

A specification table follows in the original; it is not shown here.

Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21

2025-03-01 FA Update Formula Renault 2.0 spec line notes

#37853 from Club Racing Board · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

wordingFA Formula Renault 2.0 (10-17) spec notes clarified: engine sealed, manual compliance required, tire choice unrestricted, no alterations except repairs.

As printed in Fastrack

In FA Table 2, Formula Renault 2.0 (10-17) spec line, change the notes as follows:
"Engine must remain sealed. Car must comply with year-specific Formula Renault 2.0 manual, technical regulations, and all
applicable bulletins ~~found here:~~. Competitors must have copies of these materials in their possession and present them upon
request.
~~https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/bulletins-techniques/2017,~~
~~https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/manuel-d-utilisateur/2017.~~
The following exceptions apply: Tire choice is unrestricted. No part of the car may be altered from original Formula Renault 2.0
components, except for necessary repairs that do not affect performance."

2025-03-01 AS Race memo

#37902 from American Sedan Committee · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

unclearAS Spec Lines removes ECM flexibility restriction from five Cadillac and Chevrolet/Pontiac V8 models.

As printed in Fastrack

In AS Spec Lines, change Notes as follows:
Cadillac CTS-V (04-07) Restricted Prep. 6.0L V8 (Aluminum block, Aluminum heads), LS2, 2 valves/cylinder:
"~~Any ECM maybe used.~~"
Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep. 6.2L V8 (Aluminum Block, Aluminum Heads), 2 valves per cylinder:
"~~Any ECM maybe used.~~"
Chevrolet/Pontiac Camaro & Firebird (82-92)s 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves per cylinder:
"~~Any ECM maybe used.~~"
Chevrolet/Pontiac Camaro & Firebird (93-02):

Show 3 more lines

"~~Any ECM maybe used.~~"
Chevrolet Camaro SS (V8) (10-15) Restricted Prep. 6.2L V8 (Aluminum Block, Aluminum Heads), 2 valves per cylinder:
"~~Any ECM maybe used.~~"

2025-04-01 AS Flotek Head Plunge Cut Inconsistencies

#37502 from Pamela Richardson · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

unclearAS Flotek Head plunge cut dimensions figure updated in GCR Section 9.1.6.

As printed in Fastrack

In GCR, Section 9.1.6., replace Figure 1 Value Seat Cutting Dimensions with the following:

2025-04-01 AS Notes clean up

#37693 from American Sedan Committee · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

wordingAS class notes cleanup: multiple Camaro, Firebird, CTS-V, Challenger, Mustang specs and fuel cell/ECM/head restrictions removed.

As printed in Fastrack

In AS Spec Lines, change/add to Notes as follows:
Cadillac CTS-V (04-07):
"~~Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the~~
~~stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used.~~ The
Drive Shaft Shop, Axle shaft part #'s 510220/510221 permitted."
Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep:
"~~Engine built to A/S Build Sheet specifications with the following: Head Casting #s: 14101081, 14014416 Port Volume (Max.): 081~~
~~casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb. weight reduction. Edelbrock Cylinder Head Part~~

Show 88 more lines

~~#s 608979, 608879.~~"
Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep.:
"~~Any ECM maybe used.~~"
Chevrolet/Pontiac Camaro & Firebird (82-92) Full Prep.:
"~~Engine built to A/S Build Sheet specifications with the following: Head Casting #s: 14101081, 14014416 Port Volume (Max.): 081~~
~~cast¬ing: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb weight reduction. Edelbrock Cylinder Head Part~~
~~#s 608979, 608879 are permitted. For regional competition only, unmodified GM Performance cylinder head part #s 19300955,~~
~~19300956 may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186 installed between intake~~
~~manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on each side of the restrictor.~~
~~All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98,~~
~~1.34, 1.00, 0.68 are permitted. Flo Tek Head part #102-500 are permitted.~~"
Chevrolet/Pontiac Camaro & Firebird (82-92) Restricted prep engine:
"~~Any ECM maybe used.~~"
Chevrolet/Pontiac Camaro & Firebird (93-02) Full Prep:
"~~Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.):~~
~~081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb weight reduction. Edelbrock Cylinder Head~~
~~Part #’s 608979, 608879 are permitted. For regional competition only, unmodified GM Performance cylinder head part #s~~
~~19300955, 19300956 may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186 installed~~
~~between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on each side~~
~~of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00~~
~~or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Fuel cells must be located within 24 inches of the standard tank. The 24 inch~~
~~measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with~~
~~installation of a safety fuel cell. Flo Tek Head part #102-500 are permitted.~~"
Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep:
"~~Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the~~
~~stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used.~~"
Chevrolet Camaro SS (V8) (10-15) Restricted Prep:
"~~Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the~~
~~stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used.~~"
Chevrolet Camaro (10-15) Full Prep:
"~~Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.):~~
~~081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 200 lb weight reduction. Edelbrock Cylinder Head~~
~~Part #’s 608979, 608879 are permitted. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are~~
~~permitted. Fuel cells must be located within 24 inches of the standard tank. The 24-inch measurement is taken from the~~
~~perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Flo Tek~~
~~Head part #102-500 are permitted. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is~~
~~taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel~~
~~cell.~~"
Chevrolet Camaro (16-) Full Prep:
"~~Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.):~~
~~081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 200 lb weight reduction. Edelbrock Cylinder Head~~
~~Part #’s 608979, 608879 are permitted, Flo Tek Head part #102-500 are permitted.~~"
Chevrolet Camaro, 1LE (16-):
"~~60mm flat plate restrictor required. Any ECM maybe used.~~"
Dodge Challenger (08-20) Restricted Preparation:
"~~80mm flat plate restrictor is required on the 6.4L engine. Fuel cells must be located within 24 inches of the standard tank. The~~
~~24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with~~
~~installation of a safety fuel cell.~~"
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) Full Prep:
"~~Engine built to A/S Build Sheet specifications with the following: Head Casting #s: F3ZE AA (GT40), F1ZE-AA (GT-40), F77E-AA~~
~~(GT- 40P), Port Volume (Max.): 143.00cc IN/54.00cc EX (GT-40 & GT-40P) with a 250 lb weight reduction. Edelbrock Cylinder~~
~~Head Part #s 602579, 602479 are permitted. For regional competition only, unmodified Ford Performance cylinder head part #s~~
~~M-6049-Z304DA7, M-6049-Z304D may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186~~
~~installed between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on~~
~~each side of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91,~~
~~1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Flo Tek Part # 203-500 are permitted.~~"
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri(79-86) with Restricted Prep Engine:
"~~62mm flat plate restrictor is required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch~~
~~measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with~~
~~installation of a safety fuel cell.~~ MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang Including Cobra 94-04 Full Prep:
"~~Engine built to A/S Build Sheet specifications with the following: Head Casting #s: F3ZE AA (GT40), F1ZE-AA (GT-40), F77E-AA~~
~~(GT- 40P), Port Volume (Max.): 143.00cc IN/54.00cc EX (GT-40 & GT-40P) with a 250 lb weight reduction. Edelbrock Cylinder~~
~~Head Part #s 602579, 602479 are permitted. For regional competition only, unmodified Ford Performance cylinder head part #s~~
~~M-6049-Z304DA7, M-6049-Z304D may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186~~
~~installed between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on~~
~~each side of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91,~~
~~1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Flo Tek Part # 203-500 are permitted.~~"
Ford Mustang GT (94-04) with Restricted Prep Engine:
"MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang Cobra and GT 94-95(Restricted Prep):
"~~1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,~~
~~2.43, 1.69, 1.32, 1.00, .68.~~ MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang including Cobra 96-04 (Restricted Prep):
"~~1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,~~
~~2.43, 1.69, 1.32, 1.00, .68.~~ MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang Coupe GT (05-14) Restricted Prep.:
"~~1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,~~
~~2.43, 1.69, 1.32, 1.00, .68.~~ MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted. MT82 6 speed is permitted."
Ford Mustang GT (05-14) with Restricted Prep Engine:
"~~1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,~~
~~2.43, 1.69, 1.32, 1.00, .68.~~ MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted. MT82 6 speed is permitted."
Ford Mustang GT 5.0l (15-17) Restricted Preparation:
"~~61mm flat plate restrictor required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement~~
~~is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety~~
~~fuel cell.~~ MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang GT 5.0L (2018-):
"~~60mm flat plate restrictor required.~~ MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."

2025-04-01 FE2 Driver Safety & Comfort

#37965 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

wordingFE2 allows driver safety and comfort modifications for disabled drivers with SCCA approval, not transferable to other drivers.

As printed in Fastrack

In FE2, GCR section 9.1.1.G.2.E, add the following:
"g. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

2025-05-01 AS Errors and Omission

#38055 from American Sedan Committee · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

slowerAS Ford Mustang GT 5.0L (15-17) flat plate restrictor reduced from 67mm to 64mm.

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT 5.0l (15-17), Flat Plate Restrictor Size, change as follows:
"~~67mm~~ 64mm"

2025-05-01 AS Request to Add LS1/LS6 Intakes for 5.3L Truck Engine EnO

#38197 from Jim Clark · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

wordingAS LS1/LS6 5.3L truck engine gains four approved intake part numbers: 12561269, 88894095, 89017363, 89017364.

As printed in Fastrack

In GCR, Section 9.1.6.F., add the following to Intake Part #’s:
"17113697, 19418185, 89017230, 89017363, 89017364, ~~and~~ 89017365, 12561269 and 88894095"

2025-06-01 AS Errors and Omissions

#38234 from American Sedan Committee · Rule change · TB 25-06 (2025-06 Fastrack)

Summary

wordingAS Ford Mustang GT 05-14 Restricted Prep Engine gains alternative gear ratios: 3.66, 2.43, 1.69, 1.32, 1.00, .65

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Gear Ratios the following:
"or 3.66, 2.43, 1.69, 1.32, 1.00, .65"

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2025-07-01 AS RE: Previous Letter 37695 Update

#38245 from Michael Kamalian · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

fasterAS Ford Mustang GT 5.0 2018- weight reduced from 3600 to 3525 lbs.

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT 5.0 (2018-), change Weight as follows:
"~~3600~~ 3525"

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe

2025-07-01 FA Ligier JS F3 Tire Choice

#38434 from Rocco Magni · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

tyres & wheelsFA Ligier JS F3 front tires may be Hoosier 43363 240/580R13 MS, rear 43368 300/590R13 MS.

As printed in Fastrack

In FA Table 2, FR Americas Ligier JS F3 spec line, change the notes as follows:
"Engine must be sealed in compliance with FR Americas or prior F3 Americas requirements. Car must comply with FR Americas
rules, with the following exception: front tires may be Hoosier P/N 43363, size 240/580R13 in MS compound, and rear tires may
be Hoosier P/N 43368, size 300/590R13 in MS compound. Competitors must have current copies of Formula Regional Americas
Championship Sporting Regulations, Onroak Automotive Ligier JS F3 Information Manual, and HPD engine-related specifications
and instructions in their possession and present them upon request."

2025-10-01 FE2 FE & FE2 Bubble Tail

#38978 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

wordingFE and FE2 Enterprises must use bubble tail P/N WM138014; FE2 allows only this configuration.

As printed in Fastrack

In FE, GCR section 9.1.1.G.2.F.k, change as follows:
"Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."

2025-11-01 AS Cadillac CTS-V BOP Weight Change

#38640 from Alex Lozano · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

fasterAS Cadillac CTS-V 04-07 Restricted Prep weight reduced 50 lbs to 3400.

As printed in Fastrack

In AS Spec Lines, Cadillac CTS-V (04-07) Restricted Prep., change Weight as follows:
"(Effective 11/1/2025) ~~3450~~ 3400"

2025-11-01 FA Re-Consider USF Pro 2000 Car for Formula Atlantic Class

#38783 from Augie Pabst · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

cars addedFA class adds USF Pro 2000 car eligibility for Formula Atlantic racing.

As printed in Fastrack

Effective 11/1/25 in FA Table 2, add the following:

2025-12-01 AS 1994 Mustang Spec Line Request

#39104 from Barry Borgschatz, Jr · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

unclearAS Ford Mustang GT 94-04 Restricted Prep Engine now permits Ford Motorsport M-6250-F303 camshaft.

As printed in Fastrack

In AS Spec Lines, Ford Mustang GT(94-04) with Restricted Prep Engine, add to notes the following:
"Ford Motorsport #M-6250-F303 camshaft is permitted."

Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole

2026-01-01 FA Alternate Intake Manifold for MZR

#38223 from Ove Olsson · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

unclearFA MZR gains alternate Noor P/N 0088-8-00 intake manifold with AT Power runners as option to Elan or Mazda Speed Elite.

As printed in Fastrack

In FA, GCR section 9.1.1.2.d, modify as follows:
"9. Intake manifold must be unmodified Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT, 1.882” maximum bore
diameter at throttle plates. Elan or Mazda Speed equivalent Elite intake manifold may be replaced with unmodified intake Noor
P/N 0088-8-00 with intake runners AT Power P/N 13624."
"10. Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT intake manifold must use an A aluminum spacer ~~must be~~
~~used~~ between the intake manifold and cylinder head castings; minimum spacer length is 2.200”."

2026-01-01 FA Engine Compression Rule Change Request

#39302 from Reilly Harris · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

fasterFA Formula 1000 motorcycle-based engine loses maximum compression ratio 14.5:1 limit.

As printed in Fastrack

In FA Table 2, Formula 1000 spec line, change the Engine as follows:
"Motorcycle-based 4-cycle up to 1000cc~~, maximum compression ratio 14.5:1;~~. o Otherwise, current FA engine rules apply."

2026-01-01 AS Restrictor Plate Change for Gen 2 Ford Coyote Engine

#39501 from American Sedan Committee · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

slowerAS Ford Mustang Restricted Prep engines lose 3 mm restrictor plate, from 64 mm to 61 mm.

As printed in Fastrack

In AS Spec Lines, change Restrictor as follows:
Ford Mustang Incl. Cobra and Cobra R (79-93) and Mercury Capri (79-86) with Restricted Prep Engine: "~~64 mm~~ 61 mm"
Ford Mustang GT (94-04) with Restricted Prep Engine: "~~64 mm~~ 61 mm"
Ford Mustang Coupe GT (05-14) Restricted Prep 5.0L/6 speed 4 valves per cylinder: "~~64 mm~~ 61 mm"
Ford Mustang GT (05-14) with Restricted Prep Engine: "~~64 mm~~ 61 mm"
Ford Mustang GT 5.0L (15-17) Restricted Preparation: "~~64 mm~~ 61 mm"

2026-01-01 FA Change Formula 1000 allowances

#39608 from Club Racing Board · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

fasterFA Formula 1000 allows carbon fiber external panels, forward-facing gaps, raises floor to 125mm, adds eight 75×125mm rub blocks, expands diffuser to 110cm with 75mm radius transitions.

As printed in Fastrack

In FA Table 2, Formula 1000 spec line, change the Notes as follows:
"Car must comply with December 2019 GCR Formula 1000 (FB) Preparation Rules, https://www.scca.com/downloads/48184-
gcr-december-2019/download, except as modified by this spec line. The prohibition of using carbon fiber in any external panels
or any panels licked by the airstream in Part 3.C of the December 2019 GCR F1000 (FB) Preparation Rules is removed, with the
exception that the car's floor pan/undertray must comply with the requirements of Part 2.D of the December 2019 GCR F1000
(FB) Preparation Rules. The prohibition of forward-facing gaps or openings in the bodywork in Part 3.I of the December 2019 GCR
F1000 (FB) Preparation Rules is removed. Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is modified as
follows: "Between the rear of the front tire and the front of the rear tire, no point on the lower surface of the car (the surface

Show 7 more lines

licked by the air stream) shall be more than 125mm above the plane determined by the reference area designated by the entrant
and on a line perpendicular to that reference plane." Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is also
modified as follows: "A maximum of eight (8) rub blocks of maximum dimension 75mm by 125mm are allowed anywhere on the
lower surface of the chassis and may extend below the reference plane." Part 3.E of the December 2019 GCR F1000 (FB)
Preparation Rules is modified as follows: "The radius of transitions between the diffuser sides and adjacent horizontal structures
may be up to 75mm. The width of the diffuser, as measured between its sides and above any radiused transitions, may not
exceed 110cm in any lateral section." The CRB may require the use of Flat Plate Intake Restrictors at any time."

2026-02-01 AS Edelbrock manifold (& timing kit) to Chevy LS Spec Lines Request

#39055 from Jason Smith · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

cars addedAS Chevy LS adds Edelbrock Performer RPM 71187 intake manifold with MSD 6014 ignition and 4776 Holly carburetor as spec line option.

As printed in Fastrack

In GCR, Section 9.1.6.D.2.h.2., add the following:
"(Effective 2/1/2026) i. Weight based on full preparation chassis choice spec line for GM LM7 5.3L
Carburetor Option:
Must use the full prep 4776 holly carburetor and spacer gasket
Edelbrock Performer RPM 71187 intake manifold
MSD 6014 ignition box
(Edelbrock part # kit 7118)"

2026-02-01 FA Pro Mazda Classification and Performance Enhancement Proposal

#39411 from Stephen Lamana · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

fasterFA Pro Mazda: lower intake manifold now unrestricted, throttle body raised to 80mm, wing height must not exceed 99cm, bodywork width must not exceed 132cm.

As printed in Fastrack

In FA Table 2, Pro Formula Mazda spec line, change the notes as follows:
"All current FA rules apply to areas not covered by this spec line. Apex seals unrestricted. Street port or bridge port
allowed. ~~Unmodified OEM l~~ Lower intake manifold ~~required~~ unrestricted, upper intake manifold unrestricted. Balance tube not
permitted. Fuel injection only. Maximum 70 80mm T throttle B body. The maximum height of the wing and/or
endplates ~~shall~~ must not exceed 99cm (38.98 inches). The overall maximum width of the bodywork behind the front
wheels ~~shall~~ must not exceed 132cm (51.97 inches)."

What the rules allowed changed as listed; this does not say what any particular car ran.