Sectors are not comparable across all of these events. Sector times and the theoretical lap use Runoffs 2022, Runoffs 2023 only. Runoffs 2019 (sectors cut at different points) counts towards whole-lap times and trap speed only.
One run is left out as not that car's own laps (far quicker than the car managed in any other session and than anyone else in its class all week; usually a swapped transponder): Charles Leonard in Runoffs 2022 Grp 1 Run 1 EP,FP,GTL,HP,STL,T3 Sat (2:01.165; the car's best in any other session was 2:12.686 and the rest of the class's best all week 2:07.789).
One lap is left out as timing errors (far too short to be a lap of this track). The rest of those sessions, sectors included, is used.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in; the fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed, marked ">" (with ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 NT SF → Bridge 1.03 mi
S2 Bridge → ST SF 0.90 mi
S3 ST SF → NT SF 1.35 mi
SPd In → Out 0.02 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Best lap
Best qual
Best race
Best trap
Best S1
Best S2
Best S3
Honda CRX
GTL
3
2:06.997Peter Shadowen
2:06.997Peter Shadowen
2:08.205Peter Shadowen
136.0Peter Shadowen
45.361Peter Shadowen
34.203Peter Shadowen
48.217Peter Shadowen
Nissan 200SX SE-R
GTL
8
2:07.837Bill Ball
2:07.868Bill Ball
2:07.837Bill Ball
126.4Brian Linn
45.577Brian Linn
34.046Brian Linn
48.425Brian Linn
Nissan Sentra SE-R
GTL
1
2:07.837Bill Ball
2:07.868Bill Ball
2:07.837Bill Ball
126.3Bill Ball
Nissan 200SX SE-R
GTL
3
2:08.489Brian Linn
2:08.489Brian Linn
2:12.507Ryan Downey
126.4Brian Linn
45.577Brian Linn
34.046Brian Linn
48.425Brian Linn
Nissan Sentra
GTL
1
2:10.983Paul Mevoli
2:10.983Paul Mevoli
2:11.545Paul Mevoli
122.3Paul Mevoli
46.446Paul Mevoli
34.972Paul Mevoli
51.116Paul Mevoli
Nissan 200SX
GTL
3
2:12.686Charles Leonard
2:12.686Charles Leonard
2:19.354Edward Nicholson
120.2Edward Nicholson
46.409Charles Leonard
35.492Charles Leonard
50.521Charles Leonard
Mazda MX-5
GTL
1
2:08.627Jonathan Goodale
2:08.627Jonathan Goodale
2:12.009Jonathan Goodale
127.6Jonathan Goodale
45.316Jonathan Goodale
34.318Jonathan Goodale
48.868Jonathan Goodale
MG Midget
GTL
4
2:09.129Joe Huffaker
2:09.129Joe Huffaker
2:22.317Rick Haynes
125.5Joe Huffaker
49.639Noel Hayward
39.025Noel Hayward
55.729Noel Hayward
Mazda RX-7
GTL
2
2:09.577Michael Lewis
2:09.577Michael Lewis
2:11.484Michael Lewis
127.0James Gregorius
45.454Michael Lewis
34.203Michael Lewis
48.971Michael Lewis
Nissan PL510
GTL
3
2:09.657Troy Ermish
2:09.657Troy Ermish
2:25.070Robert Pharr
121.8Troy Ermish
Toyota Tercel
GTL
2
2:11.277Graham Fuller
2:14.700Roy Lopshire
2:11.277Graham Fuller
124.0Roy Lopshire
45.758Graham Fuller
34.572Graham Fuller
50.529Roy Lopshire
Mazda Miata
GTL
3
2:12.302Taz Harvey
2:12.575Luis Rivera
2:12.302Taz Harvey
127.6Luis Rivera
46.849Luis Rivera
35.135Luis Rivera
50.020Luis Rivera
Mini Cooper
GTL
1
2:13.078Chris Kopley
2:15.598Chris Kopley
2:13.078Chris Kopley
124.0Chris Kopley
46.417Chris Kopley
35.095Chris Kopley
50.946Chris Kopley
Volkswagen Fun Cup Beetle
GTL
1
2:19.035Bryan Scheible
2:19.035Bryan Scheible
2:19.496Bryan Scheible
113.5Bryan Scheible
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Runoffs 2019 → Runoffs 2022 2019-10-05 to 2022-09-24
GTL 88-91 Honda CRX Spec Line Correction
#27233 from Jonathan Spiegel · Rule change · TB 19-12 (2019-12 Fastrack)
In GTL, Honda CRX 84-87, change notes as follows: "Hood bulge permitted, no openings. May mount wing per hatchback-station wagon spec, but no part of the wing assembly may be above the highest point of the roof. May utilize IRS with a 2.5% weight penalty." In GTL, Honda CRX 88-91, change notes as follows: "Hood bulge permitted, no openings. May mount wing per hatchback-station wagon spec, but no part of the wing assembly may be above the highest point of the roof. May utilize IRS with a 2.5% weight penalty."
GTL Request Factory Five Daytona coupe classification
#26308 from Andrew Wickline · Rule change · TB 20-01 (2020-01 Fastrack)
In GTX - MISC., Classify and add as follows: GTX – MISC. Make Model Engine Restrictor mm Weight (lbs) Notes Factory Five Type 65 Coupe R Ford 302/351
Show 2 more lines
NA 2600 Factory Five Type 65
A specification table follows in the original; it is not shown here.
GTL Request to Classify the MK1 two door Jetta
#27648 from Tim Linerud · Rule change · TB 20-01 (2020-01 Fastrack)
In GTL, classify the Jetta Mk 1 as follows: GTL Cars - Model Years Body Style Drive-line Wheel- base (in) Notes
In GCR section 9.1.2.F.6.c.1, add as follows: Alternatively, the bottom may be captured in a channel. "No clips or straps are required if bonded-glass factory windshields and/or rear windows are attached to chassis per original specifications (i.e., glass-bonding adhesive).”
GTL Wing Mounting Upright Size
#27641 from Joe Harlan · Rule change · TB 20-01 (2020-01 Fastrack)
In GT Category Specifications, section 9.1.2.F.7.b.13., add the following: “Effective 3/1/2020, F. Two wing mounting posts must be used, with each one located within 2"-20" inboard from the end of the wing. The exposed portion of the wing mounting posts must not exceed 85 square inches each. Curved brackets will be measured as if they're in a flat plane as viewed from the side. Mounting brackets are to be included in the measurement."
GTL Wing Mounting Upright Size
#27641 from Joe Harlan · Rule change · TB 20-02 (2020-02 Fastrack)
In GT Category Specifications, section 9.1.2.F.7.b.13., add the following effective 3/1/2020: "F. Two wing mounting posts must be used, with each one located within 2"-20" inboard from the end of the wing. The exposed portion of the wing mounting posts must not exceed 85 square inches each. Curved brackets will be measured as if they're in a flat plane as viewed from the side. Mounting brackets are to be included in the measurement."
GTL GTL wing end plates addition
#28243 from Grand Touring Committee · Rule change · TB 20-03 (2020-03 Fastrack)
In GTL, GCR section 9.1.2.F.7.b.13.A, change the GTL wing rules as follows: "The maximum width of the entire single element, flat plane wing assembly (wing element, endplates, and mounting hardware) is 56.0 inches, but it may be no wider than the bodywork including fender flairs. The maximum chord is 8.0 inches. Wing endplates must fit within a rectangle measuring 8.5 inches wide by 3.0 inches high. may be a maximum of 64 Sq. inches. Endplates must be flat, with no curvature or Gurney tabs. A maximum 0.5-inch wicker-bill may be employed."
GTL Clarification to letter #27406
#28309 from Grand Touring Committee · Rule change · TB 20-03 (2020-03 Fastrack)
In GTL, Mazda Engines 12A Street Port, change weight as follows: "2000 1950"
GTL GTL Wing Rule
#28754 from Grand Touring Committee · Rule change · TB 20-05 (2019-05 Fastrack)
In GTL, GCR section 9.1.2.F.7.b.13.F, add as follows: "Openings in the side view of the wing mounts are not included in the sq. inch limit."
GTL Stall Test
#28709 from Chris Doodson · Rule change · TB 20-06 (2020-06 Fastrack)
In Appendix F., SIR testing procedure:, change as follows: "The system is to be tested as is and the result is considered “as qualified or raced”. It is the responsibility of the competitor to present a system that can withstand every possible scenario that would or could result in a failed SIR stall test. The intake system shall be visually inspected for devices and design that could result in induction of additional air that did not pass through the SIR. Introduction of air behind the SIR by any means is prohibited. All inspections must be done in "as qualified or raced" condition."
GTL Request to classify 1999-2007 Toyota MR2 Spyder body
In Appendix L TA2 Rules, clarify wording as follows: “4.8.4.1.10.1.1: The maximum height of the wing, including end plates and wicker Gurney flap, can be no greater than the highest point on the roof. The roof may not be altered or pushed up to increase its height.” “4.8.4.1.10.1.5: The wing end plates must fit within a rectangle measuring 11.00 inches long by 4.00 inches tall. All wing elements, including the wicker bill Gurney flap, must be kept within the profile of the end plates. The endplates must be mounted parallel to the vehicle centerline, and must be perpendicular to the ground. Endplates must be flat, with no curvature or Gurney tabs flap. “
Show 23 more lines
“4.8.4.1.10.1.6: A wicker bill (Gurney) Gurney flap may be added to the wing element. It must be a uniform shape across the complete width of the wing. No air may pass between the wicker bill Gurney flap and the wing. It must form a 90 degree angle with the wing surface. The size of the wicker bill Gurney flap cannot exceed 0.50 inch high as measured from the wing surface. The thickness of the wicker Gurney flap material must be 0.625 inch.” “4.8.4.1.10.2.4: The dog leg style Howe endplates must be used without modification. All wing elements, including the wicker bill Gurney flap, must be kept within the profile of the end plates. The endplates must be mounted parallel to the vehicle centerline, and must be perpendicular to the ground. Endplates must be flat, with no curvature or Gurney tabs flap. “ “4.8.4.1.10.2.5: A wicker bill (Gurney) Gurney flap may be added to the upper wing element. It must be a uniform shape across the complete width of the wing. No air may pass between the wicker bill Gurney flap and the wing. It must form a 90 degree angle with the wing surface. The size of the wicker bill Gurney flap cannot exceed 0.375 inch. The thickness of the wicker bill Gurney flap must be 0.0625 inches.” “4.8.4.2.10.3.4: The dog leg style Howe endplates must be used without modification. All wing elements, including the wicker bill Gurney flap, must be kept within the profile of the end plates. The endplates must be mounted parallel to the vehicle centerline, and must be perpendicular to the ground. Endplates must be flat, with no curvature or Gurney tabs flap. “ “4.8.4.2.10.3.5: A wicker bill (Gurney flap) Gurney flap may be added to the upper wing element. It must be a uniform shape across the complete width of the wing, and must be kept within the profile of the end plates. It must form a 90 degree angle with the wing surface. The size of the wicker bill Gurney flap cannot exceed 0.375 inch high as measured from the wing surface. The thickness of the wicker Gurney flap material must be 0.0625 inch.”
In Appendix K, STO, clarify wording as follows: B.2.a.: "Wings shall be a single element with a maximum chord length of 12.00 inches, including any wicker Gurney flap." B.2.c.: "The entire rear wing assembly, including the end plates and any wicker Gurney flap, shall be mounted level with, or below, the peak of the roof."
In GT, GCR section 9.1.2.F.7.b.12., clarify Gurney flap as follows: "D. The use of fences, end rails, Gurney flaps, wickerbills,or other forward facing lips or aerodynamic devices is prohibited." "E. A maximum 0.50 inch Gurney tab flap is allowed at the trailing edge of the wing element. The tab must be mounted 90 degrees to the upper wing surface. No air may pass between the tab and the wing. The endplates must be mounted parallel to the vehicle centerline, and must be perpendicular to the ground. Endplates must be flat, with no curvature or Gurney tabs flaps." "GT3: The maximum width of the entire wing assembly (wing element, endplates, Gurney tab flap and
Show 9 more lines
mounting hardware) is 64.00 inches, but no wider than the rear body width including fender flares." In GT, GCR section 9.1.2.F.7.b.13., clarify Gurney flap as follows: "A. Endplates must be flat, with no curvature or Gurney tabs flap. A maximum 0.5-inch wicker- bill Gurney flap may be employed." In GT, GCR section 9.1.2.F.7.b.15.D., clarify Gurney flap as follows: "2. Rear Wing: Wings shall be a single element with a maximum chord length of 12.00 inches, including any wicker Gurney flap." "4. The entire rear wing assembly, including the end plates and any wicker Gurney flap, shall be mounted level with, or below, the peak of the roof."
GTL Mazda 13b Restrictor Size Follow up to Letter 28518
#29015 from Joe Harlan · Rule change · TB 20-07 (2020-08 Fastrack)
Thank you for your letter. Please see the response to letter #28518 in this Fastrack.
GTL Request to change the Mazda 13b restrictor size
#28518 from Joe Harlan · Rule change · TB 20-08 (2020-08 Fastrack)
In GTL, Engines - Mazda 13B, change as follows: Fuel Induction: "24 26mm SIR" Weight: "1950 2125" Notes: "May use a 25 27mm SIR plus 175lbs."
In GCR, Section 9.1.2.F.3.5., Specifications, change as follows: "Turbocharging/supercharging is not permitted. unless listed on the spec line."
GTL Please Add GTL Nissan 1.8L Engine MRA8DE
#29805 from Peter Zekert · Rule change · TB 21-01 (2021-01 Fastrack)
In GT Engines, classify the MRA8DE as follows: GT Engines - Engine Family Engine Type Bore x
A specification table follows in the original; it is not shown here.
GTL Increase 13b SIR size
#29867 from Grand Touring Committee · Rule change · TB 21-01 (2021-01 Fastrack)
In GTL, Spec Lines, Engines - MAZDA 13B, change as follows: Fuel Induction: "26 28mm SIR" Notes: "May use a 27mm SIR plus 175lbs."
GTL Request LP HP Fiat X1/9 & Bertone 1500 to GTL
#30058 from Larry Svaton · Rule change · TB 21-02 (2021-02 Fastrack)
In GTL, classify FIAT X-1/9 Bertone, as follows: GT Engines – FIAT X-1/9 Bertone Engine Family Engine Type Bore x Stroke (mm) Disp.
Show 2 more lines
(CC) Head Type Valves /
A specification table follows in the original; it is not shown here.
GTL Request for Help for Mazda 12A
#29754 from Michael Lewis · Rule change · TB 21-01 (2021-01 Fastrack)
In GTL Engines - MAZDA, Spec Lines, 12A, change as follows effective 3/1/2021: Fuel Induction: "27 29mm SIR" Weight: "1950 2000" Notes: "May use a 28mm SIR plus 175lbs."
GTL Request clarification for the Honda B18a,bVS B18c
#30482 from Joe Harlan · Rule change · TB 21-07 (2021-07 Fastrack)
In GTL Engines - HONDA, change Split B18 as follows: GT Engines - HONDA Engine Type Bore x Stroke (mm) Disp. (CC) Head Type Valves / Cyl. Fuel Induction Weight (lbs) Notes
Show 8 more lines
DOHC 81.0 X 87.2 1797 Alum, Crossflow 4 22.5mm SIR 2050 DOHC 81.0 x 89.0 1834 Alum, Crossflow 4 22.5mm SIR 2065
GTL Request to Allow Hood Bulge on Nissan B13 Sentra
#30504 from Jameson Savage · Rule change · TB 21-07 (2021-07 Fastrack)
In GTL Spec Lines, Sentra (B13), add to Notes as follows: "May have hood bulge (Max. of 1.5”H x 10.0” L x 6.0 W)"
GTL Request BMW E21 Classing
#30582 from Jacob Lueder · Rule change · TB 21-07 (2021-07 Fastrack)
In GT Cars - BMW, add the following: GT Cars - BMW Model Years Body Style Drive- line Wheel- base (in)
In GCR, Section 9.1.2.G.16., change as follows: "0-80541-1 0-80541-2" In GCR, Section 9.1.2.G., Appendix Z 5.a. change as follows: "0-80541-1 0-80541-2" In GCR, TA2 Appendix B.3.4, change as follows: "#6010 6014X"
In GT3 Engines - VOLKSWAGEN, classify Fun Cup Beetle EVO3 as follows: GT3 Engines - VOLKSWAGON
A specification table follows in the original; it is not shown here.
GTL Request to Classify Ginetta G40 in GTL
#31599 from Richard Gray · Rule change · TB 22-03 (2022-03 Fastrack)
In GT Cars - Ginetta G40 as follows: GTL Cars - GINETTA Model Years Body Style Drive- line Wheel- base (in) Notes Ginetta G40 2002-
Show 21 more lines
Present 2-Door Coupe RWD 88.6” Must comply with all GTL rules except as noted on spec line. May use FIA roll cage. Must have complete build specs in possession at all race events. In GT Engines - Ginetta/Ford Zetec as follows: GTL Engines - GINETTA Engine Family Bore x Stroke (mm) Disp. (CC) Head Type Valves / Cyl. Fuel Induction Weight (lbs) Notes Ginetta/Ford Zetec 80.6mm X 88.0mm 1796cc Crossflow 4 22.5 SIR 2050 + 51 lbs for IRS. + 26lbs. for sequential.
GTL Tail lights on all GT category race cars.
#32799 from John Mills · Rule change · TB 22-09 (2022-09 Fastrack)
In GT, GCR Section 9.1.2.F.7.a.6: "Glass and/or plastic headlights, front parking lights, front signal lights, lenses, and bulbs shall be removed. Headlight openings shall be covered with a wire mesh screen or panel having the same contour as the original lens, mounted so that the headlight bezel/rim remains in place, maintaining the standard appearance of the Production automobile. Side marker light assemblies shall be removed and the resulting openings covered with a plate whose dimensions do not exceed those of the original parts; side marker lights that are an integral part of the taillight assembly cannot be removed. Other lighting parts and operating mechanisms may be removed. In the case of pop-up headlights, the entire assembly may be removed and the opening covered with a screen or plate (as above, without the headlight bezel/rim requirement) which provides a stock appearance. It is not
Show 8 more lines
permitted to relocate the standard headlight, parking light, signal light, etc., openings. Traditional GT cars only. Not allowed with any "Spec Car, GT2-ST, or any other added non Traditional GT car. Taillights shall be in the original location and shall may be the original style/type of taillight for the make, model, and year of car. A rear body panel having the same contour as the original lens area and in the original location, may be fitted with a tail-light graphic of the original style/type frame/lens adhered to it. If side marker lights are an integral part of the tail-light assembly they must be represented by the panel graphic. These panel/graphics shall have a functioning red LED lamp assembly fitted through them on both sides of the car to serve as brake lights. A 15-watt or equivalent rain light may be included with-in this LED assembly or may be a separately mounted single or dual LED assembly."
Runoffs 2022 → Runoffs 2023 2022-09-24 to 2023-09-23
GTL Engine Request
#33064 from Isaac Preston · Rule change · TB 22-11 (2022-11 Fastrack)
In GTL Spec Lines, Engines - TOYOTA, add as follows:
A specification table follows in the original; it is not shown here.
GTL Fiat HP Limited Prep X1/9 Weight in GTL
#33297 from Larry Svaton · Rule change · TB 22-12 (2022-12 Fastrack)
In Gt Light Engines Spec Lines, 1500 Limited Prep (Engine & Chassis), change weight as follows: "2000 → 1835"
In GCR Appendix L-TA2 rules, Addendum A, change A.2. as follows: "The throttle body must be either a GM 90mm, electronic, part #1257 → 0790, or Edelbrock 90mm, mechanical, part 33869 or #3870." In GTA, GCR Section 9.1.2.G.3., change as follows: "The throttle body must be either a GM 90mm, electronic, part #1257 → 0790, or Edelbrock 90mm, mechanical, part 33869 or #3870."
GTL Request to add Ford Festiva to GTL
#33335 from Jason Martin · Rule change · TB 22-12 (2022-12 Fastrack)
In GT Cars - GT Light Spec Lines, add Ford Festiva as follows: GT Cars – GT Lite Model Years Body Style Drive- line Wheel- base (in) Notes Ford Festiva 1988-1993 3 Dr.
Show 4 more lines
Hatchback FWD 90.2 In GT Lite Engines, Spec Lines, add Mazda B3 as follows: GT Lite Engines -
A specification table follows in the original; it is not shown here.
GTL Toyota 4A-F and 4A-FE 1.6L DOHC 16V Engine Request
#33415 from Scott Schick · Rule change · TB 23-01 (2023-01 Fastrack)
In GT2 Spec Lines, Engines - Toyota, add the following Spec Line: Engines - TOYOTA Engine Family Engine Type Bore x
A specification table follows in the original; it is not shown here.
GTL Toyota 4Y Engine Classification Request
#33562 from Scott Schick · Rule change · TB 23-02 (2023-02 Fastrack)
In GTL Spec Lines, Engines - Toyota, add to Notes as follows: 3K: "May use 4Y block only" 4K: "May use 4Y block only" 5K: "May use 4Y block only"
GTL Please classify Fields Cardinal V8
#33784 from James Rogersn · Rule change · TB 23-05 (2023-05 Fastrack)
In GT Spec Lines, GT1 Cars - Fields Cardinal, classify Fields Cardinal V8 as follows: GT1 Cars – Fields Cardinal Model Years Body Style Drive- line Wheel- base (in) Notes Fields Cardinal V8 2023 2 Dr. RWD 92.0 Roll Cage MUST be modified to comply with
Show 6 more lines
GCR Section 9.4. In GT Spec Lines, GT1Engines - classify Ford V8 as follows: GT1 Engines - Ford Engine Family Engine Type Bore x
A specification table follows in the original; it is not shown here.
What the rules allowed changed as listed; this does not say what any particular car ran.