This track has been raced on 4 configurations (The Circuit, 2.57 mi; 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One session is left out because the timing does not look like full laps: Cal Club 2023 Qualifying #2.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
SCCA Ent FE2
FE2
5
1:39.265Jon McClintock
1:39.265Jon McClintock
1:39.712Paul Marino
156.6Paul Marino
27.234Paul Marino
28.582Paul Marino
43.028Jon McClintock
MG Midget
HP
4
1:40.295Bill Okell
2:04.965Brian Linn
2:03.082Lee Fleming
126.2Lee Fleming
27.543Bill Okell
28.857Bill Okell
43.861Bill Okell
Mazda Miata
STL
17
1:51.665Jared Korth
1:54.963Nick Leverone
1:54.845Gavin Wardle
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda MX-5
STL
6
1:51.665Jared Korth
1:57.404Ryan Gutile
1:54.845Gavin Wardle
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda Miata
STL
10
1:52.983Wesley Mollno
1:54.963Nick Leverone
1:55.682Nick Leverone
133.4Wesley Mollno
30.815Jon Davies
32.820Jon Davies
49.197Wesley Mollno
Mazda MX-5 (2015)
STL
1
2:00.239Adrian Comstock
2:00.239Adrian Comstock
2:00.722Adrian Comstock
133.0Adrian Comstock
32.847Adrian Comstock
34.493Adrian Comstock
52.675Adrian Comstock
Mazda RX-8
STL
1
1:53.515David LeCren
2:09.464David LeCren
2:11.372David LeCren
121.0David LeCren
31.217David LeCren
32.486David LeCren
49.550David LeCren
Honda Civic Si
STL
1
1:56.438Jonathan Lugod
1:57.331Jonathan Lugod
1:56.438Jonathan Lugod
106.8Jonathan Lugod
31.787Jonathan Lugod
33.468Jonathan Lugod
50.873Jonathan Lugod
Honda Prelude
STL
1
1:56.961Carl Young
1:57.917Carl Young
1:56.961Carl Young
104.5Carl Young
31.994Carl Young
33.745Carl Young
50.892Carl Young
Toyota Yaris
HP
1
2:08.224Bobby Beyer
2:10.927Bobby Beyer
2:08.224Bobby Beyer
92.3Bobby Beyer
34.660Bobby Beyer
37.206Bobby Beyer
56.144Bobby Beyer
Mini Cooper
HP
1
2:09.238Tom Tuttle
2:11.042Tom Tuttle
2:09.238Tom Tuttle
99.0Tom Tuttle
34.631Tom Tuttle
37.306Tom Tuttle
56.479Tom Tuttle
Acura integra
STL
1
2:24.310Jack McEachern
2:24.310Jack McEachern
2:24.550Jack McEachern
77.6Jack McEachern
38.960Jack McEachern
41.141Jack McEachern
1:02.410Jack McEachern
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
neutralSTL ITA/ITS RX7 and 1985+ ITA/ITS/ITB/ITC vehicles clarified to conform to section 9.1.4.2 tire specifications.
In STL Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Notes as follows: ITA-spec and ITS-spec RX7: "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires must also conform to 9.1.4.2.Tires." ITS, ITA, ITB, or ITC vehicles (1985- ): "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires must also conform to 9.1.4.2.Tires."
neutralFord Fiesta HP and Chevrolet Sonic FP model year ranges extended from 2016 to 2019.
In HP, adjust model years of the "Ford Fiesta (11-16)" spec line as follows: "Ford Fiesta (11-16 9)" In FP, adjust model years of the "Chevrolet Sonic (12-16)" spec line as follows: "Chevrolet Sonic (12-16 9)"
HP ITC to FP?
#34286 from David Snow · Rule change · TB 23-06 (2023-07 Fastrack)
neutralHP Volkswagen Rabbit Cabriolet 1780 removed; Rabbit 1588 and 1715 reclassified with engine sizes and year ranges specified.
In HP Spec Lines, Volkswagen Rabbit Cabriolet 1780, delete in its entirely: In HP, Spec Lines, Volkswagen Rabbit, change Title as follows: “Volkswagen Rabbit 1588 (includes Cabriolet / convertible)” “Volkswagen Rabbit 1715 (81-84) (excl. conv.)” “Volkswagen Rabbit GTI 1780 (83-84)”
HP Correct Intake Valve Size on 1500cc Midget/Spitfire
#34419 from Production Committee · Rule change · TB 23-06 (2023-05 Fastrack)
neutralFP and HP Sprite, Midget, and Spitfire 1500 intake valve size corrected to 36.6/(1.44).
In FP Spec Lines, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change Intake Valve Size as follows: "(I) 36.65.3/(1.44)" In FP Spec Lines, Triumph Spitfire Mk. IV & 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire Mk. III & IV 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)"
HP Larger chokes
#34681 from Brian Downey · Rule change · TB 23-09 (2023-09 Fastrack)
In HP Spec Line, Nissan/Datsun PL510, change Carburetor. No. & Type as follows: "(1) 40 DCN, DCNF w/ 32 4mm choke(s), . or (1) 36mm DCNVH. (2) auto type side draft(s) w/ 32 4mm choke(s) on I.R. manifold @ 90lbs penalty."
HP Porsche 944/924S Rule Change Request
#35002 from Adam Achepohl · Rule change · TB 23-12 (2023-12 Fastrack)
neutralEP Porsche 944/924S combines 2.5L and 2.7L variants with new weights: 2250–2415 lbs depending on engine and year.
In EP Spec Lines, delete the Porsche 944/924S 2.5L (2V) (83-88) spec line entirely, and create a new spec line for Porsche 944/924S 2.5L(2V) 2.7L(2V) (83-89) as follows:
A specification table follows in the original; it is not shown here.
HP FP and HP Toyota Corolla
#35030 from Keith Church · Rule change · TB 23-12 (2023-12 Fastrack)
fasterFP Toyota Corolla 2TC loses 43 lbs to 1810; HP Corolla loses 50–52 lbs to 1910–2006.
In FP Spec Lines, Toyota Corolla 2TC (71-74), change weight as follows: "1853 1810" In HP Spec Lines, Toyota Corolla (71-74), change weight as follows: “1960 1910 * 2009 1958 ** 2058 2006”
HP Weight Reduction for Mazda 626
#35031 from David Reiter · Rule change · TB 23-12 (2023-12 Fastrack)
fasterHP Mazda 626 84-87 weight reduced to 2200 lbs, 2255 lbs, and 2310 lbs across three configurations.
In HP Spec Lines, Mazda 626 (84-87), change weight as follows: "2300 2200 *2358 2255 **2415 2310"
HP Triumph GT6 Adjustments
#35054 from ANTHONY PARKER · Rule change · TB 23-12 (2023-12 Fastrack)
fasterEP Triumph GT6 minimum weight reduced to 1800 lbs.
In EP Spec Lines, Triumph GT6, change weight as follows: "1830 1800"
HP Request to Adjust Weight of 1988-1991 CRX/Civic
fasterHP Honda CRX 1.5 (88-91) weight reduced to 2175 lbs, 2229 lbs, and 2284 lbs across three spec lines.
In HP Spec Lines, Honda CRX 1.5 (88-91), change weight as follows: "2245 2175 *2301 2229 **2357 2284"
HP Request to Review Z3 2.5 Spec Line
#35073 from Tim Schreyer · Rule change · TB 24-01 (2024-01 Fastrack)
slowerEP BMW Z3 2.5L weight increases to 2500 lbs, 2563 lbs with turbo, 2625 lbs with supercharger.
In EP spec line, BMW Z3 2.5L, change weight as follows: "2450 2500 *2511 2563 **2573 2625"
HP Parity in HP
#35138 from Kendall Jones · Rule change · TB 24-01 (2024-01 Fastrack)
fasterHP Sprite/Midget Mk I–IV, Mk 1500 compression ratio raised to 12.0:1 at Prep Level 1/2.
In HP Spec Line, Austin-Healey Sprite Mk I, II, III, IV / MG Midget Mk I, II, III, IV & 1500, Prep Level 1/2, change Notes section as follows: "Compression ratio limited to 11 12.0:1"
STL Alternate Carburetor Request for 79-85 RX7 12a
#35181 from Dan Sheppard · Rule change · TB 24-01 (2024-01 Fastrack)
unclearSTL Mazda RX-7 12A (79-85) now allows auto-type 2 bbl with 42mm choke(s) on dual-y manifold as alternate to stock Nikki 4 bbl.
In STL Table B: Alternate Vehicle and Engine Allowances, Mazda RX-7 12A (79-85), change Notes as follows: "Street Porting of the engine only. Bridge porting, peripheral porting, and eyelash porting are prohibited. Contact SCCA National Office for details of Street porting. Stock Nikki 4 bbl carburetor on a stock manifold only. or auto-type 2 bbl w/42mm choke(s) on a “dual-y” manifold. Allow the standard removal of emissions related components, and allow air and fuel jets to be corrected. Modification of the water jacket in the area of the spark plug for cooling purposes is permitted."
HP Spitfire classification
#35224 from Michael Walz · Rule change · TB 24-01 (2024-01 Fastrack)
unclearHP Triumph Spitfire 1500 valve spec changes from 36.6/5.5/(1.44/0) to 36.6/(1.44).
In HP spec line, Triumph Spitfire 1500, make the following change to the Valves column: "(I) 36.65.5/(1.440)"
HP Miata Alternate Head
#35253 from Don Tucker · Rule change · TB 24-01 (2024-01 Fastrack)
fasterEP Mazda MX-5 1.8L 1990-97 minimum weight drops to 2150 lbs; 1994-97 variants to 2000, 2050, 2100 lbs respectively.
In EP Spec Lines, Mazda MX-5 /Miata 1.8L (90-97), change weight as follows: "2200 2150" Mazda MX-5 /Miata (94-97) "2035 2000 *2086 2050 **2137 2100"
HP Triumph GT6 Adjustments
#35255 from Anthony Parker · Rule change · TB 24-01 (2024-01 Fastrack)
In EP spec line, Triumph GT6, make the following change in the Notes section: "Two (2) 1.75” auto-type carburetors @ 1970 40 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive. Three (3) Weber 40mm DCOE w/28mm venturi on individual runner manifold @ 2020 lb."
HP Honda S2000 throttle body
#35272 from Aaron Johnson · Rule change · TB 24-01 (2024-01 Fastrack)
fasterEP Honda S2000 fuel injected throttle body inside diameter increases from 62mm to 64mm.
In EP spec line, Honda S2000, make the following changes to its spec line: Fuel Injected Equipped Throttle Body Inside Diameter: "62 64" Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .500”. An adaptor plate can be used to mount the 62mm throttle body from '00-05 to the '06-09 intake manifold. The adaptor plate can be no more than 1.25" thick, and its bore must not exceed the "Fuel Injected Equipped Throttle Body Inside Diameter" maximum spec of 64mm."
HP Front Header/Nose Panel Alternate Material For 84-87 CRX
neutralHP Honda CRX/Si 84-87 front header/nose panel may use alternate material if appearance remains stock.
In HP Spec Lines, Honda CRX/Si (84-87), in Notes, make the following change: "Compression ratio limited to 11.0:1, Valve lift limited to .390”. The front header/nose body panel can be replaced by a replica which may be constructed of an alternate material provided its appearance remains stock."
HP Correction within Triumph TR8 Spec Line
#35315 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)
neutralEP Triumph TR8 dry sump allowance moved from carburetor line to notes section.
In EP spec line, Triumph TR8 (78-81), move the "Dry sump allowed" wording to the appropriate location as follows: Carburetor. No. & Type: “Zenith Stromberg carbs or fuel injection. Dry sump is allowed.” Notes: “Comp. Ratio limited to 12.0:1, Valve lift limited to .500”. Dry sump is allowed.”
HP Correction to EP 924S/944 Spec Line
#35317 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)
neutralEP Porsche 944/924S 2.5L and 2.7L weight minimums corrected: 2479cc to 2306/2363 lbs, 2681cc to 2358/2415 lbs.
In EP spec line, Porsche 944/924S 2.5L (2V) / 2.7L (2V) (83-89), change Weight as follows:
A specification table follows in the original; it is not shown here.
HP Review Classification of HP Mazda 2
#35318 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)
In HP spec line, Mazda 2 (11-14), make the following weight changes: "1920 1995 *1968 2045 **2016 2095"
STL ST Electric-Assisted Steering Systems
#35066 from Jose Osiris Pena · Rule change · TB 24-02 (2024-01 Fastrack)
neutralSTL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems.
In GCR, Section 9.1.4.M.16., change as follows: "Power steering may be modified in any of the following ways: a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be modified internally to work without pump. b. an OEM manual steering rack for that model may be fitted c. an electric power steering pump may be fitted d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used e. an OEM hydraulic-assisted steering system may be used"
STL BOP Adjustments
#35112 from Super Touring Committee · Rule change · TB 24-02 (2024-01 Fastrack)
fasterSTL Acura/Honda B-series and Mazda MZR restrictors reduced 2mm; minimum weights down 25–75 lbs for 1900–2000cc engines.
In GCR, 9.1.4.H.1., change as follows: "Minimum weights for cars with normally aspirated piston engines will be determined by 1.35 lbs/cc displacement for the installed engine (see the following table). Displacement is the factory displacement for the installed engine. For the purpose of weight assignment, engine displacement will be rounded to the nearest 50cc (e.g., 2176cc = 2200cc and 2175cc = 2150cc)." In GCR, 9.1.4.H.1., change Minimum Weight on Chart as follows: Factory Engine Displacement 1900: "Effective 3-1-24: 2565 2540" Factory Engine Displacement 1950: "Effective 3-1-24: 2633 2583"
Show 11 more lines
Factory Engine Displacement 2000: "Effective 3-1-24: 2700 2625" In GCR, 9.1.4.H.3., change as follows: "Front wheel drive cars with a strut type front suspension may reduce their minimum weight by 2.5 percent. Effective 3- 1-24: Front wheel drive cars with 95" or less wheelbase must add 1.25% to their minimum weight." In STL Spec Lines, change Notes as follows: Acura/Honda B16: "Effective 3-1-24: 53 51mm" Acura/Honda B17: "Effective 3-1-24: 53 51mm" Acura/Honda B18C1: "Effective 3-1-24: 53 51mm" Acura/Honda B18C (JDM Type R), B18C5 (USDM Type R), B18C6 (UK and Euro Type R), B18C7 (Australia Type R): "Effective 3-1-24:52 50mm" Mazda MZR: "Effective 3-1-24: 52 50mm"
STL Mazda 12A
#35320 from Super Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)
slowerSTL Mazda 12A must keep 5th and 6th intake port actuators and valves, no longer allowed removal or disabling.
In STL Spec Lines, Table A, Mazda 12A, change Notes as follows: "The 5th and 6th intake port actuators and valves may be removed or disabled."
In HP Spec Lines, delete the following redundant spec lines in their entirety: Spec line #10 - VW Rabbit Cabriolet 1780 Spec line #3 - VW Scirocco 1588 Spec line #4 - VW Scirocco 1780 (8-valve) (83-88) Spec line #5 - VW Scirocco 1588
neutralHP Honda CRX/Si 84-87 plastic panels can be replaced with replica alternate material if stock appearance maintained.
In HP spec line "Honda CRX/Si (84-87)", make the following change to the Notes section: "The plastic OE front header/nose body panel, lower rocker side-skirt, and lower door cap panel can be replaced by a replica, which may be constructed of an alternate material, provided its appearance remains stock."
neutralNissan 300ZX 84-89 classified to EP at 2550 lbs minimum, 2960cc 6-cyl SOHC, fuel injection, 12.0:1 compression limit, 0.500" valve lift limit.
In EP Spec Lines, classify Nissan 300ZX (84-89), as follows:
A specification table follows in the original; it is not shown here.
HP RX7 1993 and Up Request In EP Spec Lines, classify
#36031 from Edward Zabinski · Rule change · TB 24-06 (2024-06 Fastrack)
neutralMazda RX-7 92-97 newly classified EP Prep Level 2 at 2200–2310 lbs with 13B 6-port rotary engine.
Mazda RX-7 (92-97) as follows:
A specification table follows in the original; it is not shown here.
HP Clean-up Multiple EP RX-8 Spec Lines In EP
#36156 from Production Committee · Rule change · TB 24-06 (2024-06 Fastrack)
neutralEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.
Spec Lines, make the following changes to the two Mazda RX-8 spec lines. Remove spec line entirely: Mazda RX-8 (04-11) Remove the wording "alternate": Mazda RX-8 (04-11)(alternate) Spec Mazda (SM/SMX) None.
fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1" In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
HP Request for Classification of 1989-1994 Suzuki Swift GT 16V Twin
neutralSuzuki Swift GT 89-94 newly classified to HP Pre at 1900 lbs, 1298cc DOHC fuel injected.
In HP Spec Lines, Classify Suzuki Swift GT (89-94) as follows:
A specification table follows in the original; it is not shown here.
STL Request to Remove Miata Hubs from General category
#37138 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)
neutralSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
In GCR, Section 9.1.4.M.18., change as follows: "18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."
HP MINI Cooper Spec Line Correction - Rear Brake Rotor Diameter
#37176 from Robert Bax · Rule change · TB 24-12 (2024-12 Fastrack)
neutralHP Mini Cooper 02-06 rear brake rotor increases from 239/9.4 mm/in to 259/10.2.
In HP Spec Lines, Mini Cooper (02-06), change Brakes Std.mm/(in.) as follows: "(F) 276/(10.9) Vented Disc (R) 239/(9.4) 259/(10.2) Solid Disc"
Applies to Mini Cooper on this page: Tom Tuttle
HP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line
#37119 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)
fasterEP BMW 325i/is E30 (84-91) weight reduced 50–52 lbs across three spec lines to 2150, 2204, 2258.
In EP SPEC LINES, BMW 325i/is (E30) (84-91), change Weight as follows: "2200 2150 *2255 2204 **2310 2258"
HP Request to Update 1988-1991 Civic to Match 1988-1991 CRX
#37466 from Michael Unger · Rule change · TB 25-03 (2025-03 Fastrack)
fasterEP Honda S2000 1997cc base loses 75 lbs to 2375; 2157cc base loses 60 lbs to 2450.
In EP, Spec Lines make the following weight changes:
A specification table follows in the original; it is not shown here.
HP Mazda 1999 Miata 1.8L
#37488 from Joe Carr · Rule change · TB 25-03 (2025-03 Fastrack)
fasterEP Mazda MX-5/Miata 99-05 minimum weight drops to 2100 lbs, 2153 lbs with power adder, 2205 lbs with two adders.
In EP Spec Lines, make the following weight change: Mazda MX-5 /Miata (99-05): "2150 2100 *2204 2153 **2258 2205"
HP MINI Cooper (07-13) Spec Line Correction: Errors and Omissions
#37560 from Robert Bax · Rule change · TB 25-03 (2025-03 Fastrack)
slowerHP Mini Cooper 07-13 engine corrected to DOHC; valve lift limit reduced to 0.390 inches.
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), change as follows: Engine Type: "4 Cyl SOHC DOHC" Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
Applies to Mini Cooper on this page: Tom Tuttle
HP Request for Classification of Chevrolet Spark
#37755 from Kristian Smith · Rule change · TB 25-04 (2025-04 Fastrack)
neutralChevrolet Spark 16-22 classified HP Pre at 1850 lbs minimum weight, fuel injected, 1399 cc.
In HP Spec Lines, classify the Chevrolet Spark (16-22):
A specification table follows in the original; it is not shown here.
HP Request to Lower Ford Festiva Minimum Weight to 1600 LBS
fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.
In HP Spec Lines "Ford Festiva (88-93)" change as follows: Weight: "1700 1600 *1743 1640 **1785 1680" Notes: "Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."
FE2 Driver Safety & Comfort
#37965 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)
neutralFE2 allows driver safety and comfort modifications for disabled drivers with SCCA approval, not transferable to other drivers.
In FE2, GCR section 9.1.1.G.2.E, add the following: "g. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
unclearSTL Mazda MX5 Challenge minimum weight now references GCR 9.1.7.1 instead of 2500 lbs; spec components removed, only alternative tires allowed.
In STL Spec Lines, Table B, Mazda Spec MX5 Challenge, change as follows: Minimum Weight: "2500 See 9.1.7.1." Notes: "Mazda MX5 Challenge car must utilize the following components: Roush CNC cylinder head 0000-01-5300,Mahle standard or +0.005 0000-01-5310, OEM camshaft, 11:1 compression ratio, header 0000-06-5407-NC, exhaust 0000-06-5427-NC, cold air intake 0000- 06-5150-KT, ECU flash 0000-01-5379, Pagid front brake pads 0000-03-5104-SP or endurance pads 0000-03- 5104-EN, Pagid rear brake pads 0000-03-5114-SP or endurance pads 0000-03-5114-EN, Penske front shock 0000-04-5291-SA, Penske rear shock 0000-04-5292-SA, Penske rear mount kit 0000-04-5358, Front mount kit 0000-04-5359, Front offset bushing 0000-04-5407-NC, Eibach front springs 0000-04-9700-08, Eibach rear springs 0000-04-9400-07, Eibach helper springs 0000-04-
Show 5 more lines
9926, Eibach front sway bar 0000-04-5306-FT, Eibach rear sway bar 0000-04-5306-RR, Interior finish panels 0000-07-5822, C&R radiator/oil cooler assembly 0000-01-5504-CR, Oil cooler adapter and lines 0000-01-5511-KT, ACT clutch 0000-02-5004-G6, wheels 17x8 #0000-04-5706-GM, # 0000- 04-5706-SL, and Toyo RR 235-40-17 dry, Toyo RA1 235-40-17 wet. Alternative tires on 17x7 wheels per STL rules. No other Super Touring modifications or allowances permitted except as noted in this spec line. Must conform completely to GCR 9.1.7.1, except alternative tires (only) per STL regs allowed."
Applies to Mazda Miata on this page: Jared Korth, Ricardo Arruda, Gavin Wardle, Ryan Gutile, Bryce Johnson, Andy Chittum, Adrian Comstock
HP Base Weight Adjustment for H-Production X1/9 Spec Lines
#38255 from Matthew Brannon · Rule change · TB 25-06 (2025-06 Fastrack)
fasterHP Fiat X-1/9 base weights reduced 50–53 lbs across 1300 and 1500 spec lines.
In HP Spec Lines, change Weight as follows: Fiat X-1/9 & Bertone1500: “1790 1740 *1835 1784 **1880 1827” Fiat X-1/9 1300: “1650 1600 *1691 1640 **1733 1680” Fiat X-1/9 1300: “2060 2010” Fiat X-1/9 1500: “1950 1900”
slowerEP BMW Z4 03-05 restricted to 52mm flat plate intake restrictor.
In EP Spec Lines, BMW Z4 (03-05), add to Notes the following: “52mm Flat Plate Intake Restrictor.”
HP EP Fiat 124 Spider Competition Adjustment Request
#38498 from John Baucom · Rule change · TB 25-07 (2025-07 Fastrack)
fasterEP Fiat 124 Spider 1600 & 2000 weight drops 50 lbs to 2000; carburetors gain 2mm chokes to 36mm.
In EP Spec Lines, Fiat 124 Sport Spider 1600 & 124 Spider 2000, change as follows: Weight: "2050 2000" Carburetor No. & Type: "(2) Weber 40 IDF-40IFI, (2) Solex C40P116, 34 36mm choke(s) req’d, (2) Weber 45DCOE w/ 34 36 mm choke(s) on I.R. manifold or fuel injection."
STL Lotus Weight Reduction
#38772 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)
fasterSTL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs.
In 9.1.2. GT2/ST Spec Lines, Lotus Evora GT4, change Weight as follows: "2750 2700" In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows: Lotus Elise Cup R: "2300 2250" Lotus Elise SC/ Lotus Exige SC: "2300 2550 2500 2450"
FE2 FE & FE2 Bubble Tail
#38978 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)
neutralFE and FE2 Enterprises must use bubble tail P/N WM138014; FE2 allows only this configuration.
In FE, GCR section 9.1.1.G.2.F.k, change as follows: "Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."
HP HP Plymouth Arrow spec omission
#38995 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralHP Plymouth Arrow transmission max speeds clarified to 4 or 5.
In HP Spec Lines, Plymouth Arrow (76-80), add the following wording to Trans. Speeds(max): "4 or 5"
HP Add Wheel Diameter to Appendix G
#39008 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP wheel diameter added to Appendix G as absolute maximum specification.
In Appendix G.2.3, change as follows: "Rim width and diameter are is absolute maximums."
HP Add TB ID tolerance to general Prod rules
#39009 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.
In GCR, Section 9.1.5.E., change as follows: 9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished." 9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must remain stock (tolerance of +/-.25mm)."
HP Please Lower Weight of 280Z
#38871 from Matthew Miller · Rule change · TB 25-09 (2025-09 Fastrack)
fasterEP Nissan 280Z minimum weight reduced from 2560 to 2400 lbs.
In EP Spec Lines, Nissan 280Z, change Weight (lbs) as follows: "(Effective 11/1/2025) 2560 2400 *2624 2460 **2688 2520"
HP Miata Weight Adjustment Follow Up
#38949 from Don Tucker · Rule change · TB 25-10 (2025-10 Fastrack)
fasterEP Mazda MX-5 1.8L 90-97 weight reduced to 2125 lbs from 2150 lbs.
In EP Spec Lines, Mazda MX-5 / Miata 1.8L (90-97), Effective 11/1/2025 make the following weight change: "2150 2125"
HP Weight Break for 1098 Midget / Sprite
#38970 from Kendall Jones · Rule change · TB 25-10 (2025-10 Fastrack)
In HP Spec Lines, Austin-Healey Sprite/Midget 1098cc, Effective 11/1/2025make the following weight change: "1630 1550"
HP HP Volvo 142 spec omission
#38994 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".
In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."
HP HP Mini DOHC 1.6
#38996 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following changes to the Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
HP Add to Rabbit description
#39019 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.
In FP Spec Lines, make the following spec line correction: "Volkswagen Rabbit (Includes Convertible Cabriolet)" In HP Spec Lines, make the following spec line correction: "Volkswagen Rabbit 1588 (Includes Cabriolet)" "Volkswagen Rabbit 1715 (Includes Cabriolet)" "Volkswagen Rabbit 1780 (Includes Cabriolet)"
HP Clean-up 9.1.5.E.7e
#39025 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.
In GCR, Section 9.1.5.E.7., change as follows: "e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear disc brakes under this rule. When converting from rear drum brakes to rear disc brakes: 1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on the vehicle’s spec line. 2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock
Show 3 more lines
from converting to rear disc brakes under this rule. 3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes as stock from converting to rear disc brakes under this rule."
HP Add TB size to Ford Mustang (94-98) Spec Line
#39130 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP Ford Mustang (94-98) fuel injected throttle body inside diameter specified at 60.
In EP Spec Lines, Ford Mustang (94-98) add the following to the Fuel Injected Equipped Throttle Body Inside Diameter column: "60"
HP Request to Re-Classsify Datsun SPL-311 to HP from FP
#39116 from Robert Heatwole · Rule change · TB 25-12 (2025-12 Fastrack)
neutralDatsun SPL-311 newly classified to HP at 2050 lbs with 1595cc OHV iron engine and specified carburetors.
In HP Spec Lines, classify Nissan/Datsun SPL 311 as follows:
A specification table follows in the original; it is not shown here.
HP TR2 Notes E&O
#39180 from Anthony Parker · Rule change · TB 25-12 (2025-12 Fastrack)
unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.
In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes: "Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."
HP Balance of Power
#39187 from Jim Simaras · Rule change · TB 25-12 (2025-12 Fastrack)
slowerEP BMW Z3 2.5L restrictor reduced 52mm to 50mm, weight increased to 2550 lbs base; five other BMW models get smaller restrictors.
In EP Spec Lines, make the following changes to Restrictors: BMW Z3 2.5L: "52mm 50mm Flat Plate Intake Restrictor" BMW Z3 2.8L (97-00): "55mm 53mm Flat Plate Intake Restrictor" BMW 328i/is E36 (96-99): "58mm 55mm Flat Plate Intake Restrictor" BMW 328i/ci E46 (01-06): "58mm 55mm Flat Plate Intake Restrictor" BMW 325i/is (E46) (01-06): "56mm 53mm Flat Plate Intake Restrictor" BMW 325is M-Technic (1994): "56mm 53mm Flat Plate Intake Restrictor" BMW 325i/is E-36 (92-95): "56mm 53mm Flat Plate Intake Restrictor"
Show 4 more lines
In EP Spec Lines, BMW Z3 2.5L, change Weight as follows: "2500 2550 *2563 2614 **2625 2678"
HP Alternative BOP Request for 84-87 Honda CRX/Civic
#39223 from Bill Lamkin · Rule change · TB 25-12 (2025-12 Fastrack)
fasterHP Honda Civic and CRX models get wider 13-inch wheels: 6 to 7 inches.
In HP Spec Lines, change Wheels as follows: Honda Civic: "13 x 6 7" Honda Civic DX (92-95): "13 x 6 7" Honda Civic/Si (84-87): "13 x 6 7" Honda Civic 1.5 (88-91): "13 x 6 7" Honda CRX/Si (84-87): "13 x 6 7" Honda CRX 1.5(88-91): "13 x 67"
HP E/O: Improve Consistency of the Spec Lines
#39500 from Robert Bax · Rule change · TB 26-01 (2026-01 Fastrack)
unclearHP Toyota MR-2 1.6L (85-89) compression ratio set to 11.0:1.
In HP Spec Line, Toyota MR-2 1.6L (85-89), change Comp. Ratio as follows: "11.0:1"
HP Request to Reclassify BMW 2002 Into H Production
#39567 from Jonathan Kinberg · Rule change · TB 26-01 (2026-01 Fastrack)
neutralBMW 2002 newly classified to H Production at 2350 lbs with 1990cc iron block, 40 DCNF carburetor, 11.0:1 compression.
In HP Spec Lines, classify BMW 2002, as follows:
A specification table follows in the original; it is not shown here.
STL Weight adjustment for STL
#39579 from Super Touring Committee · Rule change · TB 26-01 (2026-01 Fastrack)
slowerSTL minimum weights increase across all classes, 1300 cc gains 195 lbs to 1950, up to 1850 cc at 2500.
In GCR, Section 9.1.4.2.H.1. change Minimum Weight on chart as follows:
A specification table follows in the original; it is not shown here.
HP Triumph Spitfire 1296cc Compression Ratio Increase to 12:1
#39589 from Neil Verity · Rule change · TB 26-02 (2026-02 Fastrack)
fasterHP Triumph Spitfire 1296cc compression ratio increases from 11.0 to 12.0:1.
In HP Spec Lines, make the following spec line changes: Triumph Spitfire: Carburetion "Valves: (I) 33.0/(1.30) (E) 29.7/(1.17) Comp. ratio 11.0 12.0:1, Valve lift .450” Trans. Speeds: 4" Triumph Spitfire Mk. III & IV 1500: Carburetion