P2 + GT2 + FV at Buttonwillow Raceway Park

2023-04-01 GT2 Adding Ginetta G56 GTA Factory ProTune for GT2 Class

#33825 from Robert Mueller · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In GT Cars - Ginetta, Ginetta G56 GTA, add to Notes as follows:
"May use Factory installed ProMap ECU Map."

2023-04-01 P2 Remove redundant effective date language and update engine table

#34012 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, change as follows:

2023-04-01 P2 E&O - Correct dimensional equivalents

#34038 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.2, change as follows:
"Height: No part of the vehicle having special or significant aerodynamic function shall exceed a height of 115cm (45.275 inches)
above the ground with the car in normal racing trim, driver aboard."
In P2, GCR section 9.1.8.C.D.3, change as follows:
"However, no portion shall extend more than 10cm (3.937 inches) beyond a plane tangent to the outer face of the front and rear
wheels with tires."
P2 Engine Table
Spec

A specification table follows in the original; it is not shown here.

2023-05-01 GT2 Request to class 2011 Porsche Cayman S

#33771 from Coyote Black · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In GT Cars - Porsche, classify Porsche Cayman ‘S’ as follows:
GT Cars - Porsche
Model Years Body Style Drive-
line
Wheel-
base (in)
Notes
Porsche Cayman ‘S’ 09-12 2 dr. Coupe RWD 95.08 3.4L No PDK Transmission

2023-05-01 GT2 Please classify Fields Cardinal V8

#33784 from James Rogersn · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In GT Spec Lines, GT1 Cars - Fields Cardinal, classify Fields Cardinal V8 as follows:
GT1 Cars – Fields Cardinal
Model Years Body Style Drive-
line
Wheel-
base (in)
Notes
Fields Cardinal V8 2023 2 Dr. RWD 92.0 Roll Cage MUST be modified to comply with

A specification table follows in the original; it is not shown here.

2023-05-01 P2 Clarify minimum side body height requirement

#34143 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.D.6, change as follows:
"As viewed from the side, T the outermost surface of side pods body between the front and rear wheel openings and above the
floor must have a minimum height equal to the height of the front axle centerline."

2023-05-01 P2 Clarify closed cockpit single seat car allowance

#34144 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

As printed in Fastrack

In P2, GCR section 9.1.8.C.C, add a section as follows:
"4. Closed cockpit single seat cars are not permitted unless specifically allowed by a spec line in Table 1."

2023-07-01 GT2 appendix letter #33635

#34206 from Ian Barberi · Rule change · TB 23-06 (2023-07 Fastrack)

Summary

As printed in Fastrack

In GT2-ST Spec Lines, BMW E46 M3 & E36 / BMW Z3 / BMW 5000cc V8, change notes as follows:
"The 3.4 liter 6 cyl. (87.0 bore x 93.0 stroke) is permitted at 2575lbs. 4.0L V8 permitted at 2900lbs. 4.5L V8 permitted at 2950lbs.
5.0L V8 permitted at 3000lbs. Flossman body kit permitted as found at http://www.racingpartsbmw.de/start/eng/start.htm.
Trans Am SGT spec: Regular shifter 3000 lbs., paddle shifter plus 150 lbs. 95mm S54 crankshaft @ +150lbs. Lang Racing part#
S54-95mm-StrokerCrk.
S54 engine is permitted a 97mm stroke crankshaft (part #VAC-SC-S54) @2800lbs."

2023-07-01 GT2 Remove Weight and Restrictor Penalty for Corvette C7 Body

#34342 from Jorge A Nazario · Rule change · TB 23-06 (2023-07 Fastrack)

Summary

As printed in Fastrack

In GT2/ST, Chevrolet Corvette (2014-2019) change as follows:
Restrictor: "73 7mm flat plate"

2023-09-01 GT2 GT2 Mazda 20B 3 rotor ENO

#34765 from Grand Touring Committee · Rule change · TB 23-09 (2023-09 Fastrack)

Summary

As printed in Fastrack

In GT2 Spec Lines, Engines - MAZDA, combine both 20B to one spec lines and keep the following:
Weight: "2500 2280"
Notes: "Must run +100 lbs. for Grand Am transaxle and independent rear suspension. Must comply with all other GT2 rules."

2023-10-01 GT2 Late E & O

#34966 from Scotty B White · Rule change · TB 23-10 (2023-10 Fastrack)

Summary

As printed in Fastrack

RM 23-10 GT2-ST Dodge Viper, incl Comp Coupe, ACR/ACR-X VRL Front Fascia
As an Errors and omissions fix to what was originally intended for these cars, the Club Racing Board and Board of Directors have
approved the following:
In GT2-ST, Dodge Viper, incl Comp Coupe, ACR/ACR-X add VRL front fascia -100lbs to all Spec Lines.

2023-12-01 GT2 Errors in GTCS Headings and Use of the Terms Category and ClassChange existing GTL and GTA Rules

#34453 from David Gomberg · Rule change · TB 23-12 (2023-12 Fastrack)

Summary

As printed in Fastrack

from the current (or before) Table of Contents (TOC), to what is shown in the after TOC.
GTL spec lines will now be contiguous with GT2 and 3 spec lines.
GTA category and spec lines will be moved and renumbered behind GTL. GTA Section will not change but page numbers will, (as
shown in Red italics).
9.1.2.F. GT-2, 3, LITE Category Specifications 314
GT2 Cars 327
GT2/ST 341
GT3 Cars 348

2023-12-01 FV FV Wheel Bearing Clarification

#35150 from Formula/Sports Racing Committee · Rule change · TB 23-12 (2023-12 Fastrack)

Summary

As printed in Fastrack

In FV, GCR section 9.1.1.C.10.G, change as follows:
"Front W wheel bearings"

2023-12-01 P2 Correct Table 1 for Engine Date Range Specifications

#35182 from Formula/Sports Racing Committee · Rule change · TB 23-12 (2023-09 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 GT2 Dodge Viper Gen 3 hybrid Kit Update Request

#35200 from Sean McCann · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In GT2-ST Spec Lines, Dodge Viper, incl Comp Coupe, ACR/ ACR-X change NOTES as follows:
8300 OEM: "Stock OEM engine. Engine long block, valve train, and intake system must meet stock, shop manual specifications.
Hybrid update including Mopar Performance Part #P5156137. May use Mopar part #5038554AF (Gen 5 Intake Manifold
manifold allowed with (2) 55mm flat plates) and 8.4L mechanical throttle body allowed. VRL Front Fascia -100lbs."
8300: "Hybrid update including Mopar Performance Part # P5156137, Mopar part #5038554AF manifold and 8.4L mechanical
throttle body allowed using (2) 50 45mm flat plate restrictors. VRL Front Fascia –100lbs."
8400: "Intake and Throttle Body from Mopar Performance Part # P5156137allowed using (2) 50 45mm flat plate
restrictors. , Mopar part #5038554AF manifold (Gen 5 Intake Manifold allowed with (2) 50mm flat plates) VRL Front Fascia -

2024-01-01 P2 E&O - Clarify B.1 modified engine range in AMAC spec lines

#35225 from Club Racing Board · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 P2 Replacement Engine Crankcase for 07/08 Suzuki GSX-R1000 Engines

#35340 from Michael A Reupert · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line B.1, add to notes as follows:
"No modifications allowed on engines manufactured after 2008 model year. 2007-2008 Suzuki GSX-R1000 crankcase part
#11300-21860 may be replaced with 2016-2019 Suzuki GSX-S1000 crankcase part #11301-04840."

2024-02-01 GT2 Rear Blade Spoiler Clarification

#35261 from Butch Kummer · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

As printed in Fastrack

In GCR Section 9.1.2.G (GTA Category Specifications), change as follows:
“9.1.2.G.III.I
The single-plane rear spoiler must be mounted at an angel angle from 50 to 75 degrees (perpendicular to the ground
being 90 degrees) and may not extend beyond the rear bumper when viewed from directly above the rear
bumper. Spoilers must be a minimum of .063 aluminum or Lexan and may vary in overall height to match the contours
of the bodywork. The rear spoiler dimensions shall not exceed 59.0 inches wide by 5.0 inches in height, (measured on
the material surface) , or 295.0 square inches total surface area. Braces to prevent spoiler deflection are allowed, but
may serve no other purpose.”

2024-02-01 GT2 REDUCE C6 CORVETTE WEIGHT WITH OEM 7 LITER ENGINE REDUCE BY 150LB

#35385 from Mike McGinley · Rule change · TB 24-02 (2024-02 Fastrack)

Summary

As printed in Fastrack

In GT2/ST Chevrolet Corvette 7011 OEM change weight as follows:
“3275 3125“

2024-02-01 GT2 GT Direct Injection allowance and rules

#35437 from Grand Touring Committee · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 9.1.2.F.7.5.E. change as follows:
“Direct Injection is not permitted only if it came OE and must be installed using only OE high pressure pump(s), hard and
soft hoses and injectors.”

2024-02-01 GT2 GT2/3 remove Direction Injection not allowed in Spec line notes

#35439 from Grand Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)

Summary

As printed in Fastrack

In GT2/3 modify Spec Line notes as follows:
GT2:
Nissan: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.”
GT3:
Mazda: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.”
Mitsubishi 4G93: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E. ”
Nissan QR25DE/DD 1988cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.”
Nissan QE25DE/DD 2489cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.”

2024-03-01 GT2 Classify Corvette C8 (2020- ) into GT2/ST

#33759 from Andrew Aquilante · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In GT2 Spec Lines, classify Chevrolet Corvette C8 (20-) as follows:
GT2-ST Maximum Displacement Minimum Weight Restrictor Notes
Chevrolet Corvette C8
(20-)
6162 3300 71mm -
Flat Plate
LT2 engine.

Applies to Chevrolet Corvette on this page: Igor Lyustin

2024-03-01 GT2 Requesting classification for a 2015 Mitjet ST in GT2

#35408 from Jim Froula · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

As printed in Fastrack

In GT2 Spec Lines, GT Cars - MITJET ST, classify MITJET ST as follows:
GT Cars – MITJET ST
Model Years Body Style Drive-
line
Wheel-
base (in)
Notes
MITJET ST 2015 RWD 94.5 Must run per VTS specifications. Must have

2024-05-01 GT2 Request for Spec Line 1010 Reconsideration

#35009 from Kristofer Olson · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In GT2-ST Spec Lines, Acura NSX, change as follows:
Minimum Weight: "2700 3000"
Restrictor: "43 45mm TIR"

2024-05-01 P2 CN Spec ECU

#35835 from Bart Wolf · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Spec Line E, change the notes as follows:
"No engine modifications except for dry sump oil system, ECU mapping, and exhaust system the following: oil system, ECU, and
exhaust are unrestricted."

2024-05-01 GT2 Request to Eliminate the FPR from the Corvette (-2013) with LS2

#35878 from Michael Quattlebaum · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In GT2-ST Spec Lines, Chevrolet Corvette (14-19), change Restrictor as follows:
"78 80mm flat plate"

2024-05-01 P2 E&O - Correct FIA Group CN spec line notes

#35900 from Club Racing Board · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

As printed in Fastrack

In P2 Table 1, FIA Group CN spec line, change the notes as follows:
"FIA Group CN homologated chassis, brake calipers and discs, hub carriers, and suspension components are required. V de
V European Proto Endurance Series Challenge permitted bodywork, rear diffuser, wing, wheels, and assisted
shifting are allowed. Car M must comply with all other P2 requirements. Competitors must have copies of FIA Group CN
Technical Regulations and V de V European Proto Endurance Series Challenge Sporting and Technical Regulations in their
possession and present them upon request are available here: https://www.scca.com/pages/technical-forms-and-downloads."

2024-07-01 GT2 GT2-ST Rule Clarification

#36093 from Dominic Starkweather · Rule change · TB 24-07 (2024-07 Fastrack)

Summary

As printed in Fastrack

In GCR Section, Appendix K. 2012.M2, add the following:
"After market replacement differential housings are permitted as long as they are an exact equivalent."

2024-07-01 GT2 GT4 cars may run in GT2-ST

#36235 from Grand Touring Committee · Rule change · TB 24-07 (2024-07 Fastrack)

Summary

As printed in Fastrack

In 9.1.2. GT2 Spec Lines, GT3 Cars, change Note as follows:
"Note: All GT4 cars are permitted to compete in GT2-ST provided they use a factory supplied power stick or Pro Series
required restrictor. Must have GT4 rules in possession at all race events. Cars must comply with 2012 STO rules as
stated in Appendix K of the GCR. Engine Displacements in this table are nominal. Each competitor shall have available
definitive documentation (e.g., factory manual) of the original displacement for the engine used. Slicks allowed on all
GT2/ST cars with a 100-pound weight penalty."

2024-10-01 FV Disc Brakes

#36822 from Guy Bellingham · Rule change · TB 24-10 (2024-10 Fastrack)

Summary

As printed in Fastrack

In FV, GCR section 9.1.1.C.4.D, change as follows:
"Any ferrous alloy, unvented rotor may be used, but must have a maximum diameter of 11.75 in. and a minimum thickness of
0.20 in. The otherwise smooth rotor may not be cross-drilled and may have a maximum of three pad cleaning grooves per side."

2024-12-01 P2 2000 cc Pinto Engine Car Weight

#37187 from Marvin Hodges · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

As printed in Fastrack

In P2 Engine Table, Line E Note 2, add the following:
"8. Minimum weight 1335 lbs."

2025-01-01 GT2 Panoz Esperante GTS BOP

#36686 from Brian Goldburg · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In GT2 SPEC LINES, GT Engines - PANOZ, classify 2013-2016 Ford EcoBoost Twin Turbo as follows:
GT Engines – PANOZ
Engine
Family
Engine Type Bore x
Stroke
(in.)
Disp.

A specification table follows in the original; it is not shown here.

2025-01-01 GT2 Correct language regarding OEM Areo Devices

#37137 from Christopher Childs · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows:
"B. Aerodynamic Devices
2. Rear wing
c. The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level
with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule."

A specification table follows in the original; it is not shown here.

2025-01-01 GT2 GT2 Sunbeam Tiger Alternate Carburetor

#37198 from Tom Patton · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

As printed in Fastrack

In GT2 Spec Lines, GT Engines - SUNBEAM, add to Fuel Induction as follows:
"Carburetors(s) Holly 650 cfm PN #80541-1 and PN #80541-2"

2025-02-01 GT2 GT2/ST - Remove Aftermarket/Racing ABS penalty

#36538 from Jorge A Nazario · Rule change · TB 25-02 (2025-02 Fastrack)

Summary

As printed in Fastrack

In GCR, Appendix K. 2012 STO Rules, O.9., change as follows:
"May run OEM ABS or convert to an aftermarket ABS controller with 100 50 lb. weight penalty."

2025-03-01 GT2 Hood Bulge allowed

#37000 from Gordon Leslie · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In GT2 Spec Lines, GT2 Cars - PONTIAC, Fiero, change as follows:
Drive-line: "FWD RWD"
Add to Notes: "Hood bulge permitted as requested for front engine relocation only."

2025-03-01 GT2 OEM Wing Adjustment

#37590 from Christopher Childs · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

As printed in Fastrack

In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows:
"The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of
the roof. OEM aerodynamic devices do not need to adhere to the height rule."
In GCR, Section APPENDIX K. 2012 STO GENERAL TECHNICAL REGULATIONS, D.4.b., add the following:
"Factory wings, and spoilers, and roof vortex generators are permitted, but must be removed if an approved aftermarket wing is
installed. OEM aerodynamic devices do not need to adhere to the height rule."

2025-08-01 GT2 Rear Deck Lid for Older Air-Cooled Porsche

#38506 from Justin Erion · Rule change · TB 25-08 (2025-08 Fastrack)

Summary

As printed in Fastrack

In GT2 Spec Lines, GT2 Cars-Porsche, 911 Coupe & Targa., add to Notes the following:
"Porsche 911-based race cars (911,963,994), the use of the 993 3.8 RSR rear deck lid/spoiler is permitted. Aftermarket
reproductions of the original Porsche Motorsports deck lid provided they faithfully replicate OEM dimensions and functionality,
are acceptable for use."

2026-01-01 GT2 Additional Body Options to Replace Older Stock Car Bodies

#39086 from Samuel Daniels · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In GCR, Section 4.8.4.2.1., add the following:
"Cars in the class must use 1997, through current year, commercially available stock car bodywork. The following make/model
bodies are allowed:
1. Cadillac CTS
2. Chevrolet Impala
3. Chevrolet Malibu
4. Chevrolet Monte Carlo
5. Chevrolet SS

2026-01-01 GT2 GT3 Turbo to GT2?

#39365 from Chris Edens · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In GT2 Spec Lines, Engines - MAZDA, classify Engine Family BP as follows:
GT2 Engines - MAZDA
Engine
Family
Engine Type Bore x Stroke
(mm)
Disp.
(CC)

A specification table follows in the original; it is not shown here.

2026-01-01 GT2 Tech Bulletins for GT2 and GT2-ST

#39537 from Grand Touring Committee · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

As printed in Fastrack

In GT2 Spec Lines, GT2 Cars – Porsche, classify 992.1 GT3 Cup as follows:
GT2 Cars – Porsche
Model Year Body
Style Driveline Wheel Base Notes
992.1
GT3 Cup
(22-25) 2 Dr RWD 4.0L flat six. 3250lbs. w/60mm Throttle Body Restrictor (TBR).
Cars must be prepared in accordance with the appropriate

2026-02-01 GT2 Allow Larger Air Cooled Engines in Porsche 911 GT2

#39249 from Justin Erion · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

As printed in Fastrack

In GT Spec Lines, create GT Cars - PORSCHE and classify SC as follows:
GT Cars - PORSCHE
Model Years Body Style Drive- line Wheel- base
(in)
Notes
SC 1978 2 Dr. Rear engine/RWD 89.45 May use alternate engine bore.
4.0L 2V @2275 lbs. 4.0L 4V @ 2350 lbs.

2026-02-01 GT2 Classify T1 BMW in GT2

#39408 from Jared Lendrum · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

As printed in Fastrack

In GT Spec Lines, classify M3 E92 in GT Cars - BMW as follows:
GT Cars - BMW
Model Years Body Style Drive-
line
Wheel-
base (in)
Notes
M3 E92 (08-13) 2 Dr. RWD 108.7 Cannot be built to any other rule set.

A specification table follows in the original; it is not shown here.