This track has been raced on 2 configurations (The Circuit, 2.57 mi; 2.92 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Elan DP02/Mazda
P
1
1:32.576Jim Devenport
1:32.872Jim Devenport
1:33.972Jim Devenport
171.9Jim Devenport
25.461Jim Devenport
26.606Jim Devenport
40.217Jim Devenport
Dauntless Stohr
P
2
1:36.516Johnnie Crean
1:36.516Johnnie Crean
1:37.287John Manfroy
160.4John Manfroy
25.956Johnnie Crean
27.257John Manfroy
42.386John Manfroy
Dauntless Stohr
P
1
1:36.516Johnnie Crean
1:36.516Johnnie Crean
1:39.209Johnnie Crean
157.4Johnnie Crean
25.956Johnnie Crean
28.143Johnnie Crean
42.417Johnnie Crean
Dauntless-Stohr P07d
P
1
1:37.287John Manfroy
1:41.818John Manfroy
1:37.287John Manfroy
160.4John Manfroy
26.696John Manfroy
27.257John Manfroy
42.386John Manfroy
Stohr WF1
P
1
1:38.716Kevin Mitz
1:38.716Kevin Mitz
1:39.638Kevin Mitz
155.4Kevin Mitz
26.934Kevin Mitz
28.397Kevin Mitz
43.336Kevin Mitz
SCCA Ent FE2
FE2
5
1:39.265Jon McClintock
1:39.265Jon McClintock
1:39.712Paul Marino
156.6Paul Marino
27.234Paul Marino
28.582Paul Marino
43.028Jon McClintock
Penton Norma M20FC
P
1
1:39.296Joseph Moran
1:39.296Joseph Moran
1:40.832Joseph Moran
149.0Joseph Moran
27.106Joseph Moran
28.111Joseph Moran
43.651Joseph Moran
Porsche 986 Boxster
T3
1
1:51.337Reto Eberle
128.4Reto Eberle
29.898Reto Eberle
33.530Reto Eberle
54.812Reto Eberle
Ford Mustang
T3
5
1:55.675Scotty B White
1:55.965Roger Eagleton
1:55.675Scotty B White
137.2Scotty B White
31.598Scotty B White
33.496Scotty B White
50.029Scotty B White
Nissan 370Z
T3
1
1:56.241Gamaliel Aguilar-Gamez
1:56.241Gamaliel Aguilar-Gamez
1:56.899Gamaliel Aguilar-Gamez
131.8Gamaliel Aguilar-Gamez
31.456Gamaliel Aguilar-Gamez
33.615Gamaliel Aguilar-Gamez
50.788Gamaliel Aguilar-Gamez
BMW Z4M
T3
1
1:59.315J. David Orem
2:00.000J. David Orem
1:59.698J. David Orem
128.1J. David Orem
32.480J. David Orem
34.645J. David Orem
51.770J. David Orem
BMW 330ci
T3
1
1:59.844Ron Tanemura
1:59.844Ron Tanemura
1:59.971Ron Tanemura
136.3Ron Tanemura
32.188Ron Tanemura
34.401Ron Tanemura
52.107Ron Tanemura
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
fasterT3 Spec Z 350Z rear wheel width increases to 10 inches; HR Engine restrictors change from 42mm to 44mm.
In T3 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo Spec Z (03-08), change as follows: Max Wheel Size (inch): "18 x 9 (F) 18 x 10 (R)" Notes: "Nissan Motorsports: Shock Front left P/N E6110-SZ350 & Front right E6111- SZ350 & rear E6210-SZ350, springs front P/N 54010-SZ350 & rear 55020- SZ350, F&R 5600S-SZ350, Front sway bar max 37mm. Rear sway bar max 25mm, Bushings P/N (54541, 54560, 55045, 55148, 55149, 55152, 55153, 55158, 56218) - RRZ30 allowed. Nismo flywheel permitted. SPC Control Arms 72125 and 72123 are allowed. HR Engine: Two 42mm flat plate restrictors required. Zspeed and Z1 alternative clutch slave permitted. Must conform to all SpecZ 2018 Edition rules. No other touring allowances beyond 2018 SpecZ edition rules or allowances listed here. Nissan brake part numbers NISMO Race Front Caliper Kit 41001-FR350, NISMO Front Rotor-RIGHT 40206-
Show 3 more lines
SZ350, NISMO Front Rotor-LEFT 40207-SZ350 permitted. 44011-RC350 rear caliper kit permitted, 43206-SZ350 Right rotor permitted, 43207-SZ350 Left rotor permitted. Car must conform to the Official 2024 Spec Z Rules. HR Engine: Two 44mm flat plate restrictors required. Tires must conform to Spec Z rules. Competitor must be able to provide a copy of the current rules."
neutralT3 Nissan 350Z and 370Z now allow brake booster vacuum regulator, must not be in-car adjustable.
In T3 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo (03-08), add to Notes as follows: "Brake booster vacuum regulator allowed, cannot be in-car adjustable." In T3 Spec Lines, Nissan 370Z, incl. Nismo (2009-2022), add to Notes the following: "Brake booster vacuum regulator allowed, cannot be in-car adjustable."
Applies to Nissan 370Z on this page: Gamaliel Aguilar-Gamez
T3 Mustang Help
#35559 from Ross Murray · Rule change · TB 24-03 (2024-03 Fastrack)
fasterT3 Ford Mustang 4.6L restrictor holes increased from 40 mm to 45 mm.
In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), change Notes as follows: "A flat plate restrictor with two 40 mm 45mm holes required directly behind throttle body."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 Appeal for Retention of T3 Mazda RX-8 Spec Line (Letter #35378)
#35577 from Raymond Blethen · Rule change · TB 24-03 (2024-03 Fastrack)
unclearT3 Mazda RX-8 Spec Line retention appeal directed to letter #35584 for ruling.
Thank you for your letter. Please see letter #35584 in current Fastrack.
neutralMazda RX-8 04-12 expiration date removed; no longer expires 12/31/24.
In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change Notes as follows: "**This Spec line will expire 12/31/24, Please submit to appeal**"
T3 Subaru WRX (02-05) Appeal
#35656 from Anthony Piselli III · Rule change · TB 24-03 (2024-03 Fastrack)
neutralT3 Subaru WRX (02-05) spec line expiration deadline removed; class now permanent.
In T3 Spec Lines, Subaru WRX (02-05), change Notes as follows: "**This Spec line will expire 12/31/24, Please submit to appeal**"
T3 Allow T4 and T3 RX8 to Disable/Remove Factory Oil Inj.
#35761 from David Mead · Rule change · TB 24-05 (2024-05 Fastrack)
unclearT3 and T4 Mazda RX-8 may remove or disable factory oil injection system.
In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows: "OEM oil injection system may be removed or disabled." In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows: "OEM oil injection system may be removed or disabled."
T3 Driveshafts
#35916 from Scotty B White · Rule change · TB 24-05 (2024-05 Fastrack)
slowerT2, T3, T4 driveshafts may use alternative materials or one-piece units; non-OEM adds 25 lbs.
In GCR Section 9.1.9.2.D.4.b., add the following: "6. T2-T3- Driveshafts may be replaced with alternative materials ie. carbon fiber, aluminum, steel. Two-piece driveshafts may be replaced with one-piece units. If non-OEM driveshaft is used, add 25 lbs."
neutralAudi S4 00-02 in T3 must compete in 3 Super Tour events before Runoffs eligibility.
In T3 Spec Lines, Audi S4 (00-02), add to Notes as follows: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
unclearT3 Mazda MX-5 Global Cup Miata ND1/ND2 tire size changes to 225 DOT specification.
In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND2, change Tire Size as follows: "Series Mazda MX5 Cup spec tires: 215/610 R17 BF Goodrich G-Force Slick, 20/61- 17 G-Force Wet-P2G or 225 DOT"
T3 Mustang T2/T3
#35877 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)
unclearFord Mustang GT 5.0L and V6 now permit Track/Performance Package parts in T2 and T3.
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes as follows: "Track/Performance Package parts permitted." In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows: "Track/Performance Package parts permitted." In T3 Spec Lines, Ford Mustang V6 (15-17), change Notes as follows: "Track/Performance package allowed."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 T2-T4 Driveshaft Mistake...?
#36050 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)
fasterT2-T4 Ford Mustangs: remove 25 lbs penalty for non-OEM driveshaft, clarify alternate driveshaft allowances.
In GCR Section 9.1.9.2.D.4.b.6., remove as follows: "If non-OEM driveshaft is used, add 25 lbs." In T2 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows: "Driveshaft from Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang Boss 302 (12-13), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang GT 5.0L (11-14)ki, change Notes as follows: "Alternate metallic driveshaft is allowed."
Show 12 more lines
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L (05-10), change Notes as follows: 'An Aluminum driveshaft is allowed." "Alternate metallic driveshaft is allowed." In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), change Notes as follows: "An Aluminum driveshaft is allowed." "Alternate metallic driveshaft is allowed." In T3 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows: "Driveshaft from Alternate metallic driveshaft is allowed."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
fasterT3 Nissan 350Z DE engine now permits cold air intake.
In T3 Spec Lines, Nissan 350ZTrack/ Touring/Standard/Nismo(03-08), add to Notes as follows: "DE engine: Cold air intake permitted."
T3 B8/8.5 Audi S4 T3 and T2
#36195 from Brian Leib · Rule change · TB 24-07 (2024-07 Fastrack)
neutralAudi S4 (2000-2002) moves to T3 with 3400 lbs minimum weight, 38mm turbo inlet restrictor required.
In T3 Spec Lines, Classify Audi S4 (2000-2002) as follows and allow the T2 spec line to expire.
A specification table follows in the original; it is not shown here.
T3 Z4 Roadster Eligibility
#36196 from Allan Unruh · Rule change · TB 24-07 (2024-07 Fastrack)
neutralT3 BMW Z4 3.0si expands to include 3.0i Roadster and Coupe (07-08); hardtop permitted with positive fasteners.
In T3 Spec Lines, BMW Z4 3.0si, & Coupe (07-08) change Model and add to Notes as follows: "BMW Z4 3.0si, 3.0i, Roadster & Coupe (07-08)" Notes: "Any OEM or aftermarket hardtop permitted that retains the OEM roof silhouette (if a hardtop is used, latches shall be replaced with positive fasteners)."
T3 Honda Civic Si (2017+)
#36249 from Jason LaManna · Rule change · TB 24-08 (2024-08 Fastrack)
fasterT3 Honda Civic Si (2017-2021) restrictor removed, weight to 2950 lbs, Runoffs eligibility requires 3 Super Tour events.
In T3 Spec Lines, Honda Civic Si (2017-) with 2900 weight, change as follows: Model: "Honda Civic Si (2017-2021)" Restrictor: "36mm TIR" Add to Notes: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**" In T3 Spec Lines, Honda Civic Si (2017-), change as follows: Model: "Honda Civic Si (2017-2021)" Restrictor: "36mm TIR" Weight (lbs): "30752950"
Show 1 more lines
Add to Notes: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
T3 Subaru Reliability Help
#36284 from Anthony Piselli III · Rule change · TB 24-08 (2024-08 Fastrack)
neutralT3 Subaru STI (15-20) and WRX STI (03-07) permitted to use OEM spec block #IAG-ENG-S550 and head studs.
In T3 Spec Lines, Subaru STI (15-20), add to Notes the following: "OEM spec block permitted # IAG-ENG-S550, Head studs permitted." In T3 Spec Lines, Subaru WRX STI (03-07), add to Notes the following: "OEM spec block permitted # IAG-ENG-S550, Head studs permitted."
neutralT3 VW Golf R (12-13 and 15-18) 36mm TIR placement now allows OEM turbo inlet, removing 60mm distance limit from impeller.
In T3 Spec Lines, Volkswagen Golf R (12-13), change Restrictor Required as follows: "36mm TIR max 60mm from impeller TIR may be placed in the OEM turbo inlet as long as the restriction is entirely within the leading edge of the housing." In T3 Spec Lines, Volkswagen Golf R (15-18), change Restrictor Required as follows: "36mm TIR max 60mm from impeller TIR may be placed in the OEM turbo inlet as long as the restriction is entirely within the leading edge of the housing."
T3 Redundant Verbiage Regarding Mustang Spec Lines for Driveshaft
#36484 from David Mead · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT2 and T3 Mustang spec lines remove redundant driveshaft alternate/aluminum allowance wording.
In T2 Spec Lines, change Notes as follows: Ford Mustang V6 (11-14): "Alternate driveshaft is allowed." Ford Mustang Boss 302 (12-13): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (11-14): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (15-17): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (2018-): "Alternate driveshaft is allowed. Springs up to 800#/in front and rear permitted. Alternate metallic driveshaft permitted." Ford Mustang Coupe GT & Shelby GT 4.6L (05-10): "Alternate driveshaft is allowed."
Show 4 more lines
In T3 Spec Lines, change Notes as follows: Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10): "Alternate driveshaft is allowed." Ford Mustang V6 (11-14): "Alternate driveshaft is allowed." Ford Mustang V6 (05-10): "An Aluminum driveshaft is allowed."
neutralT2, T3, T4 fuel cell installations may remove charcoal canisters, emissions valves, and sensors.
In GCR, Section 9.1.9.2.D.1.c. add the following: "5. Removal of ancillary fuel tank equipment charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket fuel cell installations."
neutralT2, T3, T4 brake component wording clarified: 2-piece rotors allowed in T2 within 5% OE diameter, T3 within 2% OEM diameter.
In GCR, Section, 9.1.9.2.D.6. Brakes, change as follows: "a. Components 1. The make and material of brake pads and linings may be changed. 2. Brake fluid may be substituted with any brake fluid. 3. Brake rotor dust shields may be removed or replaced to accommodate brake ducts. 4. Flexible rubber brake lines may be replaced with Teflon lined, metal braided hoses. 5. Any brake ducts are permitted, but they must serve no other purpose. Fender liners may be modified solely for routing and attachment of brake ducts. Duct intake openings may be created by the opening of 2 sections up to 14.5 square inches each in
Show 10 more lines
the front fascia. The stock headlamp location is not permitted for brake ducting. Two alternative duct openings may be created by the removal of the fog lights or 2 sections up to 14.5 square inches each of stock false grills originally located in the front fascia. 6. Stock replacement brake rotors may be obtained from sources other than the manufacturer provided they are the exact equivalent of the stock rotors. In T2 only - 2-piece rotors with ferrous metal rotor disks and aluminum hats are allowed, must be within 5% of OE diameter. In T3 only - 2-piece front rotors with ferrous metal rotor disks and aluminum hats are allowed, must be within 2% of OEM diameter. Drilled and slotted rotors are permitted. 7. Parking brakes, mechanisms, and actuating components may be removed. 8. Brake vacuum reservoirs sized 0.50 gallons or smaller are permitted. The port or fitting at the vacuum source may not be modified, enlarged or relocated. The vacuum reservoir and brake booster must be a closed system."
neutralT2, T3, T4 fuel cell cars may remove charcoal canisters, emissions valves, and sensors.
In GCR, Section, 9.1.9.2.D.1.c., add the following: "5. Removal of ancillary fuel tank equipment; charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket fuel cell installations."
T3 Allow Spec MX5 upgrade kit for 2009-11 RX8 S2 Transmision
#37140 from Chris Braunlich · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT3 and T4 Mazda RX-8 and MX-5 permit transmission kit #0000-02-5700.
In T4 Spec Lines, add the following to Notes: Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted. Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted." In T3 Spec Lines, add the following to Notes: Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted." Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted."
T3 Move Spec Boxster to T4
#37158 from Rob Piekarczyk · Rule change · TB 24-12 (2024-12 Fastrack)
neutralPorsche Spec Boxster moves to T4, minimum weight 2750 lbs, requires 3 Super Tour events before Runoffs eligibility.
In T4 Spec Lines, classify Porsche Spec Boxster, as follows:
A specification table follows in the original; it is not shown here.
T3 BMW 320i Spec Line
#37204 from chi ho · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT4 BMW 320i 14-15 Spec Line expires 12/31/24 removed; Turner Motorsports intercooler #024703TMS02 allowed.
In T4 Spec Lines, BMW 320i (14-15), change Notes as follows: "**This Spec line will expire 12/31/24, Please submit to appeal** Turner Motorsports intercooler #024703TMS02 allowed."
T3 Classification for a 2005 Cadillac CTS 3.6 liter 6 speed manual
fasterT3 Subaru WRX STI 03-07 drops 100 lbs to 3200; Legacy GT/Spec B 05-09 drops 150 lbs to 3200.
In T3 Spec Lines, Subaru WRX STI (03-07), change Weight as follows: "3300 3200" In T3 Spec Lines, Subaru Legacy GT/Spec B (05-09), change Weight as follows: "3350 3200"
T3 Request to Move Spec Mustang to Touring 3 (from T2)
#37080 from Roger Eagleton · Rule change · TB 25-01 (2025-01 Fastrack)
neutralFord Spec Mustang moves to T3 with 44mm bore restrictor, 275 max tire, 3450 lbs minimum weight.
In T3 Spec Lines, classify Ford Spec Mustang as follows:
A specification table follows in the original; it is not shown here.
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 3.7 Mustangs BoP
#37186 from Scotty B White · Rule change · TB 25-01 (2025-01 Fastrack)
fasterT3 Ford Mustang V6 (11-14) and (15-17) now permit cold air intake.
In T3 Spec Lines, Ford Mustang V6 (11-14), add to Notes the following: "Cold air intake permitted." In T3 Spec Lines, Ford Mustang V6 (15-17), add to Notes the following: "Cold air intake permitted."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
In T2, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Acura TL SHAWD (10-13) Audi S4 (12-14) Audi S5 (13-14) Audi TT RS (2018-) Cadillac ATS-V (16-17) Cadillac CTS-V (06-07) Chevrolet Camaro SS (98-02)
Show 49 more lines
Honda Civic Type-R (2017-) Saturn Sky / Convertible (07-09)" In T3, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Audi TTS Coupe (10-11) Cadillac ATS (2015) Chevrolet Cobalt (05-07) Dodge SRT-4 (03-05) Ford Fiesta ST (2014-) Hyundai Genesis Coupe (2010-) Hyundai Veloster Turbo (18-21) Mini Cooper S (2016-) Toyota Camry (11-15)" In T4, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Acura Integra GS-R VTEC (3 or 4 door) (94-01) Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05) Chevrolet Cobalt SS, Sport Coupe (06-10) Chevrolet Sonic RS (2011-) Chrysler/Dodge Neon ACR SOHC (4 door) (01-02) Dodge Dart (14-15) Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99) Fiat 500 Abarth (12-14) Ford Focus SVT (02.5-04) Ford Focus ZX4 ST (05-06) Ford Focus (08-11) Ford Mustang V-6 (01-04) Honda Accord LX & EX (03-07) Honda Accord LX-S/EX/EX-L (08-12) Honda Civic Coupe Si (99-00) Honda Civic SI (02-03) Hyundai Elantra GLS (11-12) Hyundai Tiburon V-6 (03-08) Hyundai Veloster Turbo/ R-Spec (14-15) Kia Forte Koup and Sedan LX/EX (10-13) Kia Forte Koup and Sedan SX (10-13 Kia Forte Koup (14-15) Mazda Protégé ES (2000) Mazda Protégé 5 (02-03) Mazda6 s (03-07) Mitsubishi Eclipse GT (00-05) Nissan Sentra SER (02-03) Pontiac Firebird V-6 (96-02) Scion tC (03-07) Subaru Impreza (non-turbo) (04-06) Toyota Celica GT (00-05) Toyota Celica GTS/GT (00-05) Volkswagen Golf TDI (2010) Volkswagen Passat (12-14) Volkswgen Passat TDI (12-14) Volkswgen Passat 1.8T (2014-)"
fasterT3 Nissan 350Z HR Engine FPR restrictor increases from 47mm to 49mm.
In T3 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo (03-08), change Required Restrictor as follows: "HR Engine: (2) 47mm 49mm FPR"
T3 Request to Classify Club Spec in Appropriate Touring Classes
#37523 from Andrew Benagh · Rule change · TB 25-02 (2025-02 Fastrack)
neutralFord SCCA Club Spec Mustang classified T3 at 3350 lbs with driver; Mazda SCCA Club Spec MX-5 classified T4 at 2500 lbs with driver.
In T3 Spec Lines, classify Ford SCCA Club Spec Mustang (CSM) as follows:
A specification table follows in the original; it is not shown here.
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
P Correct text in engine table notes
#37606 from Club Racing Board · Rule change · TB 25-02 (2025-02 Fastrack)
neutralPrototype Staudacher and unrestricted engine notes corrected for minimum weight wording.
In Prototype Engine Table, Spec Line B, change the notes as follows: "Staudacher cars may run 950 lb min. wt. minimum weight with 38.5mm flat plate intake restrictor." In Prototype Engine Table, Spec Line D, change the notes as follows: "No restrictor required at 1150 lb min. wt. minimum weight."
P Update Prototype class designation
#37653 from Club Racing Board · Rule change · TB 25-02 (2025-02 Fastrack)
neutralPrototype class renamed from P1 to P, affecting designation throughout rules with no performance changes.
In Categories and Classes, GCR section 9.1, change as follows: "9.1.8. SPORTS RACING CATEGORY CLASSES A Sports Racing (ASR) Regional Class Prototype 1 (P1)" In Homologation Requirements, GCR section 9.2.2, change as follows: "All Formula, Sports Racing, and P1, and P2 cars must be constructed in strict accordance with the rules and regulations contained in the current GCR unless specifically excepted." In Non-Metallic Wheel/Chassis Construction, GCR section 9.3.37, change as follows:
Show 20 more lines
"Non-metallic wheel construction is prohibited. Non-metallic chassis construction is prohibited, except in ASR, P1, FS and FA." In Appendix B, GCR section 1.4.2.G, change as follows: "It is preferable not to combine GT1, AS, T1, T2, T3, and STU with P1, P2, SRF, FP, HP, or GTL." In Appendix C, GCR section 2.6.G, change as follows: "A 14 or 15 year-old must complete his first SCCA driver school in a car not classed in GT1, GT2, FA, FB, F S, ITR, ASR, P1, P2, or T1." In Appendix E, section 1, change as follows: "Depending on the length and banking of the oval course being used, it is recommended that Regions consider restricting the faster classes (GT1, FA, and P 1) from competition at oval track events." In Sports Racing Category, GCR section 9.1.8.1, change as follows: "The SCCA Sports Racing Category shall be for automobiles which are designed and constructed for road racing competition, offering provisions for a driver and passenger, or a driver alone (single-seater). They shall conform to the following requirements. Sports Racers Cars except SRF & SRF3 homologated prior to 1-1-2014 are eligible to compete as P1 or P2 as long as they meet applicable class rules,; no re-homologation is required." "Single seat Formula car chassis (Ex.: FA, FC, FF, FV) fitted with enclosed bodies (as specified in these rules) may run in a Sports Racing/Prototype Class (ASR, P 1, P2) provided they comply with the requirements of the Classification Specification and GCR Section 9." In Sports Racing Category, GCR section 9.1.8.2, change as follows: "In an effort to control shock/damper technology and cost to a level reasonable for Road Racing, in ASR, P1, and P2, any fluid dampers are allowed with the following restrictions:"
Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21
T3 SpecE46 Tire Change
#37421 from Simon Foweather · Rule change · TB 25-04 (2025-04 Fastrack)
unclearT3 BMW Spec E46 updates to SpecE46 rules Version 1.1 dated Jan. 6, 2025.
In T3 Spec Lines, BMW Spec E46, change Notes as follows: "Must conform to all SpecE46 rules Version 2.10. Version 1.1 dated Jan. 6, 2025."
T3 S197 Mustang V6 in T3
#37594 from John LoGiudice · Rule change · TB 25-04 (2025-04 Fastrack)
fasterT3 Ford Mustang V6 11-14 minimum weight drops 25 lbs to 3325.
In T3 Spec Lines, Ford Mustang V6 (11-14), change Min. Weight as follows: "3350 3325"
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
FE2 Driver Safety & Comfort
#37965 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)
neutralFE2 allows driver safety and comfort modifications for disabled drivers with SCCA approval, not transferable to other drivers.
In FE2, GCR section 9.1.1.G.2.E, add the following: "g. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
T3 S550 Mustang
#38061 from Scotty B White · Rule change · TB 25-05 (2025-05 Fastrack)
fasterT3 Ford Mustang V6 15-17 weight drops 50 lbs to 3350, brake options clarified with M2300V now 50 lb penalty or Brembo alternative.
In T3 Spec Lines Ford Mustang V6 (15-17), change as follows: Weight: "3400 3350" Notes: "Rear spring relocated to shock allowed. 800lbs springs (F/R) allowed. Track/ Performance Package parts permitted. Optional: 6 speed automatic transmission (with paddle shifters). Sway bars allowed up to 38mm (F) 28mm (R). Ford Motorsports 6-piston M2300V 380mm brake kit allowed with +50lb penalty, or optional 2-piece rotor 355mmmax Brembo brake kit #M- 2300-S allowed. Cold air intake permitted."
P Add missing punctuation marks
#38150 from Club Racing Board · Rule change · TB 25-05 (2025-05 Fastrack)
neutralClass P adds clarification notes on restrictor requirements, throttle bodies, Mazda 12A engine spec, and P2 auto-based engine rules.
In P Engine Table, Spec Line D notes, add the following: "No restrictor required at 1150 lbs. minimum weight." In P Engine Table, Spec Line G notes, add the following: "Group CN non-composite chassis with Honda K20A-FD2 may use unrestricted individual throttle bodies at 1500 lbs. minimum weight." In P Table 1, Beasley B2 spec line notes, add the following: "Engine must be Mazda 12A rotary with 40.5mm venturi. Car must comply with all other Prototype requirements." In P Table 1, P2 cars built to 2000cc auto-based specification spec line notes, add the following:
Show 3 more lines
"Car must comply with all other P2 rules applicable to cars using stock production-based four-cylinder automotive engines. Note: Competitors are also free to modify their cars to comply with the general Prototype rules and Engine Table Spec Line H instead."
unclearT3 BMW Spec E46 rules updated to Version 3.0 from Version 1.1.
In T3 Spec Lines, BMW Spec E46, change Notes as follows: "Must conform to all SpecE46 rules Version 2.10. Version 1.1 dated Jan. 6, 2025. Version 3.0."
unclearBMW Spec E46 in T3 updates to SpecE46 rules Version 3.0.
In T3 Spec Lines, BMW Spec E46, change Notes as follows: "Must conform to all SpecE46 rules Version 2.10. Version 1.1 dated Jan. 6, 2025. Version 3.0."
T3 Incorrect Touring Heading
#38451 from Terry Hanushek · Rule change · TB 25-08 (2025-08 Fastrack)
neutralT2, T3, T4 Spec Lines table header changed from T2 to ET.
In T2-T4 Spec Lines, change Table Header as follows: "T2 ET"
P RM 25-05 - Prototype Engine Table A, 2 Cycle Restrictor Change
#38929 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)
slowerPrototype Engine Table A 2-cycle restrictor reduces from 40mm to 38mm venturi size.
Effective 8/1/25 in Prototype Engine Table, Spec Line A, change the restrictor as follows: "40mm 38mm Restricted Venturi Size"
P 13B Rotary Engine Rules Change Request
#38856 from Jason Vinkemulder · Rule change · TB 25-09 (2025-09 Fastrack)
unclearP class 13B rotary engine restrictor changes to 40mm SIR fuel injection or 41.5mm venturi carburetor.
Effective 9/1/25 in Prototype Engine Table, Spec Line K, change the restrictor as follows: "40mm SIR with fuel injection or 41.5mm venturi with carburetor"
P Add Radical Cup series Radical SR3 spec line to Table 1
#38916 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)
neutralPrototype class adds Radical SR3 spec line to Table 1 effective 9/1/25.
Effective 9/1/25 in Prototype Table 1 (Spec Line Cars), add the following:
P Clarify spec line cars language
#38943 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)
neutralPrototype P2 cars may now run P2 spec or modified Prototype spec in Prototype class; clarified language and added Radical Cup series table.
Effective 9/1/25, in Prototype, GCR section 9.1.8.B.K, change as follows: "P2 cars may compete in either the Prototype class or the P2 class but must participate in the Prototype class to the extent necessary to qualify for an invitation to the Runoffs in Prototype. P2 cars may be modified to comply with the general Prototype rules and Prototype Engine Table or may continue to run in P2 specification in the Prototype class as permitted in Table 1 below." Table 1 (Spec Line Cars)
A specification table follows in the original; it is not shown here.
FE2 FE & FE2 Bubble Tail
#38978 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)
neutralFE and FE2 Enterprises must use bubble tail P/N WM138014; FE2 allows only this configuration.
In FE, GCR section 9.1.1.G.2.F.k, change as follows: "Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."
T3 Make the S2000 Competitive Again
#38470 from David Mead · Rule change · TB 25-08 (2025-08 Fastrack)
fasterT3 Honda S2000 wheels grow to 17x9.0 front and 17x10 rear; tyres widen to 255 front and 275 rear.
In T3 Spec Lines, Honda S2000 (all) (00-09), change as follows: Max Wheel Size: "(Effective 11/1/2025) 17 x 9.0 (f) 17 x 10 (r)" Tire size: "(Effective 11/1/2025) 245 255 (f) 275 (r)" Notes: "(Effective 11/1/2025) CAI allowed, Header allowed."
T3 ND Gearset Request for T4
#39166 from Josh Smith · Rule change · TB 25-11 (2025-11 Fastrack)
neutralT3 and T4 Mazda MX-5 Miata models add approved gear kit PT#-0000-02-6100 to notes.
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T3 Spec Lines, Mazda MX-5 Miata (16-18), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, add to Notes the following: "Gear kit Kit PT#- 0000-02-6100."
T3 ND Spec Lines Wrong PT#'s
#39170 from Josh Smith · Rule change · TB 25-11 (2025-11 Fastrack)
neutralT4 Mazda MX-5 Miata/Club/RF (19-24) and (16-18) remove discontinued hardtop part #0000-07-5901; T3 MX-5 Miata (16-18) and Global Cup ND (16-21) same.
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must remain stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5804-01). Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs #0000-04-9700-08, springs up to 500lb front and 300lb rear allowed. Mazda tower brace 0000-04-5626 allowed. Mazda header
Show 20 more lines
0000-06-5410 allowed." In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. Up to 500lb front and 300lb rear springs allowed. Mazda Motorsports Header part #0000-06-5410 allowed. Mazda tower brace 0000-04-5626 allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5." In T3 Spec Lines, Mazda MX-5 Miata (16-18), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Header permitted. Cold air intake permitted. Front strut brace permitted. Front and rear sway bars permitted up to 35mm, Springs 800 front and 800 Rear max permitted. Any OEM or aftermarket hardtop permitted that retains the OEM roof silhouette including Mazda hardtop part #0000-07-5902- ND and part #0000-07-5901 (discontinued DG Motorsports top). If a hardtop is used, latches shall be replaced with positive fasteners. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, change Notes as follows: "Shoulder harness installation must conform to FIA mounting specifications that are approved for this vehicle per section 6.2 FIA article 253, safety equipment. Must meet all ND2 MX-5 Global Cup rules. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop Mazda hardtop part #0000-07-5902-ND and #0000-07-5902-ND part #0000- 07-5901 (discontinued DG Motorsports). If a hardtop is used, latches shall be replaced with positive fasteners. OBD2 requirement does not apply. Ballast box may be removed. ND2s with sequential gearbox allowed +100 lbs.
unclearT3 Ford Mustang EcoBoost loses optional 2-piece 355mm Brembo rotor brake kit option with 50 lb penalty.
In T3 Spec Lines, Ford Mustang EcoBoost (2015-), change Notes as follows: ", or optional 2-piece rotor 355mm max Brembo brake kit #M-2300-S allowed with +50lb penalty."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 Request to Allow Spec Mustang to Touring 3 in Appendix M Trim
#39196 from Roger Eagleton · Rule change · TB 26-01 (2026-01 Fastrack)
fasterT3 Ford Spec Mustang restrictor opens to 45mm, weight drops to 3400 lbs.
In T3 Spec Lines, Ford Spec Mustang, change as follows: Restrictor: "Two 44mm 45mm holes" Weight: "3450 3400"
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 Tire Help for Spec E9X in T3
#39222 from Benjamin Phillips · Rule change · TB 26-01 (2026-01 Fastrack)
fasterT3 BMW Spec E9X tire width increases to 255 from 225; spec E9X tire or any DOT permitted.
In T3 Spec lines, BMW Spec 9X, change as follows: Car: "BMW Spec 9X BMW Spec E9X" Notes: "Must conform to all SpecE9X rules Version 2.10. Spec E9X spec tire permitted or any DOT permitted up to 225 255 permitted. No other touring allowances permitted. Engines may not be modified unless specified in the Spec E46 rules and must conform to touring tech procedures. Driver must possess a current copy of the rules. Dyno results do not ensure engine compliance. THIS SPEC LINE DOES NOT QUALIFY FOR SCCA RUNOFFS COMPETITION UNTIL IT HAS BEEN REPRESENTED IN 3 SCCA SUPER TOUR EVENTS."
T3 SpecE46 Tire Sizing
#39292 from Rob Piekarczyk · Rule change · TB 26-01 (2026-01 Fastrack)
fasterT3 SpecE46 permitted tire width increases from 225 to 245.
In T3 Spec Lines, BMW SpecE46, change Notes as follows: "Must conform to all SpecE46 rules Version 3.0. SpecE46 spec tire permitted or any DOT permitted up to 225 245 permitted. No other touring allowances permitted. Engines may not be modified unless specified in the Spec E46 rules and must conform to touring tech procedures. Driver must possess a current copy of the rules. Dyno results do not ensure engine compliance. SE46 HP limit does not apply."
T3 Alternate Placement of Fuse Panel and Electronics Request
neutralT2, T3, T4 cars may relocate under-dash electronics and fuse boxes for access after roll cage installation.
In GCR, Section 9.1.9.2.D.9.d, add the following: "8. Under-dash electronics including computers, modules and fuse boxes may be relocated so they can be easily accessed after roll cage installation."
neutralPrototype carbon-carbon and carbon-ceramic brake rotors now permitted instead of prohibited.
In Prototype, GCR section 9.1.8.B.F.2, change as follows: "Brake calipers may be ferrous or aluminum alloy. Effective 1/1/2026, carbon-carbon and carbon-ceramic brake rotors are prohibited and rotors must be ferrous. Brake rotor material is unrestricted."
T3 Clarify T4 Brake Rotor Allowance
#39503 from David Mead · Rule change · TB 26-01 (2026-01 Fastrack)
neutralT4 Performance now permits 1-piece alternative rotors matching spec line sizes; alternate brake kits allowed same.
In GCR, Section 9.1.9.2.D.6.a.6., change as follows: "In T2-Performance alternative rotors, including 2 piece rotors are permitted. Rotors must be within 5% of OE diameter or a maximum diameter of 360mm. In T3- Performance alternative rotors, including 2 piece rotors are permitted with a maximum diameter of 360mm. T4- Performance alternative 1-piece rotors are permitted but rotors must meet the sizes listed in the spec line. Spec lines showing alternate brake kits are also permitted to use 1-piece performance alternative rotors of the same size."
T3 Please change 2011-2014 Mustang V6 Spec Line to 2005-2014
#39558 from Matthew Miller · Rule change · TB 26-02 (2026-02 Fastrack)
neutralT3 Ford Mustang V6 Spec Line expands to include 2005-2010 chassis and body with 2011-2014 engine.
In T3 Spec Lines, Ford Mustang V6 (11-14) , add to Notes the following: "2005-2010 chassis/body permitted."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 Nissan 350Z Weight Request
#39598 from David Muramoto · Rule change · TB 26-02 (2026-02 Fastrack)
fasterT3 Nissan 350Z DE Motor loses 25 lbs to 3100, HR Motor loses 25 lbs to 3250.
In T3 Spec Lines, Nissan 350Z Track/ Touring/Standard/ Nismo (03-08), change Weight as follows: DE Motor: "3125 3100" HR Motor: "3275 3250"
T3 Allow Alt Bushing Material in Toe Links
#39607 from David Mead · Rule change · TB 26-02 (2026-02 Fastrack)
fasterT2-T4 adjustable toe links now allow performance alternative bushings and spherical bearings, previously prohibited except in specified examples.
In GCR, Section 9.1.9.D.5.a.1., change as follows: "T2-T4: A maximum of 3.5 degrees of negative camber is allowed on front and rear suspensions. Spec line part(s) may not be modified to increase caster and camber. Strut suspensions may adjust camber and caster by the use of eccentric bushings, eccentric bolts (crash bolts) at the strut-to-spindle, and/or by use of slotted adjustment plates at the top of the strut mounting plate. If upper strut slotted adjustment plates are used, they shall be located on existing chassis structure, utilizing the unmodified manufacturer’s original bolt holes and may not serve as reinforcement for that structure. Slotted adjustment plates (strut camber plates) may incorporate a single spherical bearing (spherical bushing) and a ball thrust bearing per strut tower. On other forms of suspension, camber and caster adjustment may be achieved by the use of shims and/or eccentric
Show 4 more lines
bushings. Adjustable toe links with spherical bearings are permitted and may serve no purpose other than adjusting toe angle. Adjustable toe links are permitted. They are allowed to have performance alternative bushings and spherical bearings. They may serve no purpose other than adjusting toe angle. Spherical bearings/bushings are not permitted in T2-T4 except for the specific examples listed in the class rules or vehicle spec line."
What the rules allowed changed as listed; this does not say what any particular car ran.