This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One session is left out because the timing does not look like full laps: Cal Club 2023 Qualifying #2.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Swift Db6
FF
2
1:49.259Edward Erlandson
1:55.247Johnnie Crean
1:54.993Johnnie Crean
124.5Johnnie Crean
31.358Johnnie Crean
32.841Johnnie Crean
47.766Edward Erlandson
SWIFT DB-6 Honda
FF
1
1:49.259Edward Erlandson
47.766Edward Erlandson
Swift Db6
FF
1
1:54.993Johnnie Crean
1:55.247Johnnie Crean
1:54.993Johnnie Crean
124.5Johnnie Crean
31.358Johnnie Crean
32.841Johnnie Crean
50.291Johnnie Crean
Piper DL7-Honda
FF/STL
2
1:51.118Eric Poulsen
1:52.044Eric Poulsen
1:51.118Eric Poulsen
114.7Eric Poulsen
30.276Eric Poulsen
31.650Eric Poulsen
48.818Eric Poulsen
Piper DL7-Honda
FF
1
1:51.118Eric Poulsen
1:52.044Eric Poulsen
1:51.118Eric Poulsen
114.7Eric Poulsen
30.276Eric Poulsen
31.650Eric Poulsen
48.818Eric Poulsen
Honda Prelude
STL
1
1:56.961Carl Young
1:57.917Carl Young
1:56.961Carl Young
104.5Carl Young
31.994Carl Young
33.745Carl Young
50.892Carl Young
Mazda Miata
EP/FP/STL
21
1:51.665Jared Korth
1:53.088Glen McCready
1:53.487Glen McCready
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda MX-5
EP/STL
8
1:51.665Jared Korth
1:53.088Glen McCready
1:53.487Glen McCready
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda Miata
EP/STL
11
1:52.034Joe Carr
1:54.963Nick Leverone
1:55.682Nick Leverone
133.4Wesley Mollno
30.815Jon Davies
32.405Joe Carr
49.197Wesley Mollno
Mazda MIata
FP
1
1:56.276Steven Powers
1:57.032Steven Powers
1:56.276Steven Powers
134.3Steven Powers
31.570Steven Powers
33.696Steven Powers
50.716Steven Powers
Mazda MX-5 (2015)
STL
1
2:00.239Adrian Comstock
2:00.239Adrian Comstock
2:00.722Adrian Comstock
133.0Adrian Comstock
32.847Adrian Comstock
34.493Adrian Comstock
52.675Adrian Comstock
SWIFT DB-
FF
1
1:53.098Edward Erlandson
1:53.098Edward Erlandson
1:54.741Edward Erlandson
133.7Edward Erlandson
30.951Edward Erlandson
32.299Edward Erlandson
49.791Edward Erlandson
Mazda RX-8
STL
1
1:53.515David LeCren
2:09.464David LeCren
2:11.372David LeCren
121.0David LeCren
31.217David LeCren
32.486David LeCren
49.550David LeCren
Mazda RX-7
EP/FP
3
1:55.440Michael Lewis
1:56.121Michael Lewis
1:55.440Michael Lewis
128.8Michael Lewis
31.255Michael Lewis
33.299Michael Lewis
50.204Kurt Frietzsche
Nissan Sentra SE-R
FP
1
1:55.722Brian Linn
1:57.239Brian Linn
1:55.722Brian Linn
128.3Brian Linn
31.416Brian Linn
33.400Brian Linn
50.478Brian Linn
Volkswagen GTI
FP
1
1:56.016Tim Linerud
2:06.156Tim Linerud
93.4Tim Linerud
33.738Tim Linerud
35.656Tim Linerud
55.246Tim Linerud
Honda Civic Si
STL
1
1:56.438Jonathan Lugod
1:57.331Jonathan Lugod
1:56.438Jonathan Lugod
106.8Jonathan Lugod
31.787Jonathan Lugod
33.468Jonathan Lugod
50.873Jonathan Lugod
Fiat X 1/9
FP
1
1:59.128Daniel Snow
2:00.398Daniel Snow
1:59.128Daniel Snow
137.8Daniel Snow
31.878Daniel Snow
34.053Daniel Snow
52.221Daniel Snow
BMW E30
EP
1
2:00.712Sean Lovett
2:00.712Sean Lovett
2:01.864Sean Lovett
127.6Sean Lovett
32.761Sean Lovett
34.806Sean Lovett
53.058Sean Lovett
Porsche Boxster
EP
1
2:01.940William Robinson
2:01.940William Robinson
2:02.887William Robinson
130.6William Robinson
32.969William Robinson
35.257William Robinson
53.408William Robinson
Porsche 914-4
FP
1
2:15.932Garey Raymond
2:21.274Garey Raymond
2:15.932Garey Raymond
84.8Garey Raymond
37.237Garey Raymond
39.091Garey Raymond
59.604Garey Raymond
Acura integra
STL
1
2:24.310Jack McEachern
2:24.310Jack McEachern
2:24.550Jack McEachern
77.6Jack McEachern
38.960Jack McEachern
41.141Jack McEachern
1:02.410Jack McEachern
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
FF Add Fast Forward Part Numbers for Honda Fit Engine
wordingFF Honda Fit engine adds Fast Forward part number alternatives for intake, exhaust, oil system, and scavenge pump components.
As printed in Fastrack
In FC/FF, GCR section 9.1.1.B.14.a.6, change as follows: "For all Honda part numbers in these specifications, superc seding part numbers are considered equivalent. In FC/FF, GCR section 9.1.1.B.14.f.5, change as follows: "Cylinder head breather restrictor must be used as supplied by HPD or Fast Forward, unmodified.: HPD PN: 15262-F21S-A200; Fast Forward PN: FF200-503." In FC/FF, GCR section 9.1.1.B.14.k.2, change as follows: "The upper manifold, air box and throttle body assembly must be used as delivered from Honda, HPD, or Fast Forward as noted below."
Show 35 more lines
In FC/FF, GCR section 9.1.1.B.14.k.2, insert as follows: "a. Intake manifold: HPD PN: 17210-F21S-A210; Fast Forward PN: FF200-201. b. Throttle body: Honda Fit: PN: 16400ZZ5024; HPD PN: 16400ZZ5024; Fast Forward PN: FF200-104. c. Throttle lever: HPD PN: 17330-F21S-A210; Fast Forward PN: FF200-101." In FC/FF, GCR section 9.1.1.B.14.k.3, change as follows: "All gaskets and sensors utilized on the inlet manifold from head to throttle body must be Honda Fit OEM, or HPD supplied or Fast Forward as noted below. a. Gasket In. manifold: HPD PN: 17105-RB0-004, Honda Fit OEM. b. Gasket, EGR chamber cover: HPD PN: 17146-RB0-004, Honda Fit OEM. c. Gasket In. port: HPD PN: 17115-RB0-007, Honda Fit OEM. d. Gasket, restrictor: HPD PN: 17399-F21S-A200, (2 required) HPD; Fast Forward PN: FF200-109. Two required." In FC/FF, GCR section 9.1.1.B.14.k.5, change as follows: "The Honda Fit engine is required to have an HPD supplied air inlet restrictor supplied by HPD or Fast Forward: HPD PN: 17344- F21S-A201; Fast Forward PN: FF200-110, with internal diameter of 30.5mm and thickness of 3.175mm (0.125 inches) correctly installed within the intake system." In FC/FF, GCR section 9.1.1.B.14.m.1, change as follows: "The exhaust manifold must be as supplied by HPD or Fast Forward:, HPD part # PN: 18150-F21S-A200 or # PN: 1818 50-F21S-B200; Fast Forward PN: FF500-001 or PN: FF500-002." In FC/FF, GCR section 9.1.1.B.14.n.1, change as follows: "The oil pan, baffle plate, and scavenge pump filter fittings must be as supplied by HP or Fast Forward as noted below. No modifications are permitted. a. Oil pan: HPD PN: 11200-F21S-A210 or PN: 11200-F21S-C240; Fast Forward PN: FF100-201A or PN: FF100-201B. b. Oil pan baffle plate: HPD PN: 11221-F21S-A210; Fast Forward PN: FF100-202. c. Oil scavenge pump filter fittings (2 required): HPD PN: 15180-F21S-A210; Fast Forward PN: FF100-204." In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows: "The scavenge pump and internal scavenge pump parts must be as supplied from HPD or Fast Forward as noted below." In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows: "b. Rotor outside diameter: HPD 44.400mm (1.748 inches):; Fast Forward 40.640mm (1.600 inches). c. Scavenge pump rotor set: HPD PN: 15450-F21S-A20; Fast Forward PN: FF100-110. d. Oil pump: HPD PN: 15100-F21S-A200; Fast Forward PN: FF100-100A. e. Scavenge pump cartridge: 15111-F21S-A21; Fast Forward PN: FF100-127. f. Scavenge pump port A: HPD PN: 15137-F21S-A20; Fast Forward PN: FF100-101. g. Scavenge pump port B: HPD PN: 15139-F21S-A20; Fast Forward PN: FF100-102. h. Scavenge pump shaft: HPD PN: 15510-F21S-A20; Fast Forward PN: FF100-103. i. Scavenge pump front cover: HPD PN: 15070-F21S-A21; Fast Forward PN: FF100-104."
slowerEP BMW Z3 2.5L intake restrictor reduced from 58mm to 56mm flat plate.
As printed in Fastrack
Effective 4/1/2023 In EP Spec Line BMW Z3 2.5L, change Notes as follows: "58 56mm Flat Plate Intake Restrictor is required with both stock or alternate throttle body."
wordingSTL ITA/ITS RX7 and 1985+ ITA/ITS/ITB/ITC vehicles clarified to conform to section 9.1.4.2 tire specifications.
As printed in Fastrack
In STL Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Notes as follows: ITA-spec and ITS-spec RX7: "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires must also conform to 9.1.4.2.Tires." ITS, ITA, ITB, or ITC vehicles (1985- ): "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires must also conform to 9.1.4.2.Tires."
wordingFord Fiesta HP and Chevrolet Sonic FP model year ranges extended from 2016 to 2019.
As printed in Fastrack
In HP, adjust model years of the "Ford Fiesta (11-16)" spec line as follows: "Ford Fiesta (11-16 9)" In FP, adjust model years of the "Chevrolet Sonic (12-16)" spec line as follows: "Chevrolet Sonic (12-16 9)"
wordingFP and HP Sprite, Midget, and Spitfire 1500 intake valve size corrected to 36.6/(1.44).
As printed in Fastrack
In FP Spec Lines, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change Intake Valve Size as follows: "(I) 36.65.3/(1.44)" In FP Spec Lines, Triumph Spitfire Mk. IV & 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire Mk. III & IV 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)"
FP Correct Intake Valve Size on 1500cc Midget/Spitfire
wordingFP and HP Sprite, Midget, and Spitfire 1500 intake valve size corrected to 36.6/(1.44).
As printed in Fastrack
In FP Spec Lines, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change Intake Valve Size as follows: "(I) 36.65.3/(1.44)" In FP Spec Lines, Triumph Spitfire Mk. IV & 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire Mk. III & IV 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)"
wordingEP Triumph TR8 78-81 removes alternate front hub allowance note; stock hubs now required.
As printed in Fastrack
In the EP Spec Lines, Triumph TR8 (78-81), remove the following wording from Notes: "Alternate front hubs are allowed provided they are of the same external dimensions as stock and weigh no less than the stock hubs."
cars addedEP Porsche 944/924S combines 2.5L and 2.7L variants with new weights: 2250–2415 lbs depending on engine and year.
As printed in Fastrack
In EP Spec Lines, delete the Porsche 944/924S 2.5L (2V) (83-88) spec line entirely, and create a new spec line for Porsche 944/924S 2.5L(2V) 2.7L(2V) (83-89) as follows:
A specification table follows in the original; it is not shown here.
cars addedEP Porsche 944/924S combines 2.5L and 2.7L variants with new weights: 2250–2415 lbs depending on engine and year.
As printed in Fastrack
In EP Spec Lines, delete the Porsche 944/924S 2.5L (2V) (83-88) spec line entirely, and create a new spec line for Porsche 944/924S 2.5L(2V) 2.7L(2V) (83-89) as follows:
A specification table follows in the original; it is not shown here.
fasterFP Toyota Corolla 2TC loses 43 lbs to 1810; HP Corolla loses 50–52 lbs to 1910–2006.
As printed in Fastrack
In FP Spec Lines, Toyota Corolla 2TC (71-74), change weight as follows: "1853 1810" In HP Spec Lines, Toyota Corolla (71-74), change weight as follows: “1960 1910 * 2009 1958 ** 2058 2006”
unclearSTL Mazda RX-7 12A (79-85) now allows auto-type 2 bbl with 42mm choke(s) on dual-y manifold as alternate to stock Nikki 4 bbl.
As printed in Fastrack
In STL Table B: Alternate Vehicle and Engine Allowances, Mazda RX-7 12A (79-85), change Notes as follows: "Street Porting of the engine only. Bridge porting, peripheral porting, and eyelash porting are prohibited. Contact SCCA National Office for details of Street porting. Stock Nikki 4 bbl carburetor on a stock manifold only. or auto-type 2 bbl w/42mm choke(s) on a “dual-y” manifold. Allow the standard removal of emissions related components, and allow air and fuel jets to be corrected. Modification of the water jacket in the area of the spark plug for cooling purposes is permitted."
In EP spec line, Triumph GT6, make the following change in the Notes section: "Two (2) 1.75” auto-type carburetors @ 1970 40 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive. Three (3) Weber 40mm DCOE w/28mm venturi on individual runner manifold @ 2020 lb."
In EP spec line, Triumph GT6, make the following change in the Notes section: "Two (2) 1.75” auto-type carburetors @ 1970 40 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive. Three (3) Weber 40mm DCOE w/28mm venturi on individual runner manifold @ 2020 lb."
fasterEP Honda S2000 fuel injected throttle body inside diameter increases from 62mm to 64mm.
As printed in Fastrack
In EP spec line, Honda S2000, make the following changes to its spec line: Fuel Injected Equipped Throttle Body Inside Diameter: "62 64" Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .500”. An adaptor plate can be used to mount the 62mm throttle body from '00-05 to the '06-09 intake manifold. The adaptor plate can be no more than 1.25" thick, and its bore must not exceed the "Fuel Injected Equipped Throttle Body Inside Diameter" maximum spec of 64mm."
fasterEP Honda S2000 fuel injected throttle body inside diameter increases from 62mm to 64mm.
As printed in Fastrack
In EP spec line, Honda S2000, make the following changes to its spec line: Fuel Injected Equipped Throttle Body Inside Diameter: "62 64" Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .500”. An adaptor plate can be used to mount the 62mm throttle body from '00-05 to the '06-09 intake manifold. The adaptor plate can be no more than 1.25" thick, and its bore must not exceed the "Fuel Injected Equipped Throttle Body Inside Diameter" maximum spec of 64mm."
wordingFF Honda Fit gains Fast Forward FF800-100 oversize piston ring pack option.
As printed in Fastrack
In FF, GCR section 9.1.1.B.14.e.3.a, add the following: "The standard ring pack, PN 13011-RB1-004 (Riken) or 13011-RB1-006 (Nippon), or the oversize ring pack, PN 13021-RB7-Z01 (Riken), or 13021-RB7-Z02 (Nippon), or FF800-100 (Fast Forward), may be used."
wordingEP Triumph TR8 dry sump allowance moved from carburetor line to notes section.
As printed in Fastrack
In EP spec line, Triumph TR8 (78-81), move the "Dry sump allowed" wording to the appropriate location as follows: Carburetor. No. & Type: “Zenith Stromberg carbs or fuel injection. Dry sump is allowed.” Notes: “Comp. Ratio limited to 12.0:1, Valve lift limited to .500”. Dry sump is allowed.”
wordingEP Triumph TR8 dry sump allowance moved from carburetor line to notes section.
As printed in Fastrack
In EP spec line, Triumph TR8 (78-81), move the "Dry sump allowed" wording to the appropriate location as follows: Carburetor. No. & Type: “Zenith Stromberg carbs or fuel injection. Dry sump is allowed.” Notes: “Comp. Ratio limited to 12.0:1, Valve lift limited to .500”. Dry sump is allowed.”
wordingSTL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems.
As printed in Fastrack
In GCR, Section 9.1.4.M.16., change as follows: "Power steering may be modified in any of the following ways: a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be modified internally to work without pump. b. an OEM manual steering rack for that model may be fitted c. an electric power steering pump may be fitted d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used e. an OEM hydraulic-assisted steering system may be used"
fasterSTL Acura/Honda B-series and Mazda MZR restrictors reduced 2mm; minimum weights down 25–75 lbs for 1900–2000cc engines.
As printed in Fastrack
In GCR, 9.1.4.H.1., change as follows: "Minimum weights for cars with normally aspirated piston engines will be determined by 1.35 lbs/cc displacement for the installed engine (see the following table). Displacement is the factory displacement for the installed engine. For the purpose of weight assignment, engine displacement will be rounded to the nearest 50cc (e.g., 2176cc = 2200cc and 2175cc = 2150cc)." In GCR, 9.1.4.H.1., change Minimum Weight on Chart as follows: Factory Engine Displacement 1900: "Effective 3-1-24: 2565 2540" Factory Engine Displacement 1950: "Effective 3-1-24: 2633 2583"
Show 11 more lines
Factory Engine Displacement 2000: "Effective 3-1-24: 2700 2625" In GCR, 9.1.4.H.3., change as follows: "Front wheel drive cars with a strut type front suspension may reduce their minimum weight by 2.5 percent. Effective 3- 1-24: Front wheel drive cars with 95" or less wheelbase must add 1.25% to their minimum weight." In STL Spec Lines, change Notes as follows: Acura/Honda B16: "Effective 3-1-24: 53 51mm" Acura/Honda B17: "Effective 3-1-24: 53 51mm" Acura/Honda B18C1: "Effective 3-1-24: 53 51mm" Acura/Honda B18C (JDM Type R), B18C5 (USDM Type R), B18C6 (UK and Euro Type R), B18C7 (Australia Type R): "Effective 3-1-24:52 50mm" Mazda MZR: "Effective 3-1-24: 52 50mm"
In HP Spec Lines, delete the following redundant spec lines in their entirety: Spec line #10 - VW Rabbit Cabriolet 1780 Spec line #3 - VW Scirocco 1588 Spec line #4 - VW Scirocco 1780 (8-valve) (83-88) Spec line #5 - VW Scirocco 1588
In HP Spec Lines, delete the following redundant spec lines in their entirety: Spec line #10 - VW Rabbit Cabriolet 1780 Spec line #3 - VW Scirocco 1588 Spec line #4 - VW Scirocco 1780 (8-valve) (83-88) Spec line #5 - VW Scirocco 1588
wordingFP Honda CRX 84-87 can replace plastic front header, rocker skirt, door cap panels with stock-appearance replicas in alternate materials.
As printed in Fastrack
In FP spec line "Honda CRX / CRX Si (84-87)", add the following wording to the Notes section: "The plastic OE front header/nose body panel, lower rocker side-skirt, and lower door cap panel can be replaced by a replica, which may be constructed of an alternate material, provided its appearance remains stock."
slowerFP Acura Integra and Honda Civic models now require 55mm Flat Plate Intake Restrictor.
As printed in Fastrack
In the following FP spec lines, add the following wording to the Notes section: Acura Integra (90-93) Acura Integra LS (94-01) Acura Integra GSR (92-93) Honda Civic Del Sol VTEC (94-97) Honda Civic Si (99-00) "55mm Flat Plate Intake Restrictor is required."
wordingEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.
As printed in Fastrack
Spec Lines, make the following changes to the two Mazda RX-8 spec lines. Remove spec line entirely: Mazda RX-8 (04-11) Remove the wording "alternate": Mazda RX-8 (04-11)(alternate) Spec Mazda (SM/SMX) None.
wordingEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.
As printed in Fastrack
Spec Lines, make the following changes to the two Mazda RX-8 spec lines. Remove spec line entirely: Mazda RX-8 (04-11) Remove the wording "alternate": Mazda RX-8 (04-11)(alternate) Spec Mazda (SM/SMX) None.
wordingFF VTEC activation valve must function; EGR blanking plate rule clarified with Fast Forward part numbers.
As printed in Fastrack
In FF, GCR section 9.1.1.B.14.r.1, change as follows: "All emission control devices must be removed and blocked off by the blanking plate provided by HPD or Fast Forward as noted below, except for the VTEC activation valve. The VTEC activation valve must be retained; and it must be functioning. No modifications are permitted. a. EGR Plate: Fast Forward PN: FF200-301. b. EGR Port Cover: Fast Forward PN: FF200-302."
fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.
As printed in Fastrack
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1" In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.
As printed in Fastrack
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1" In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
fasterFF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs.
As printed in Fastrack
In FF, GCR section 9.1.1.B.20.A.3, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight." In FC, GCR section 9.1.1.B.20.B.4, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
wordingFF Honda Fit allows Fast Forward 0.25mm oversize pistons PN FF800-110 as alternative; piston diameter spec clarified to 2.8835 inches.
As printed in Fastrack
In FF, GCR section 9.1.1.B.14.e.1, change as follows: "Honda Fit OEM standard size pistons, PN: 13010-RB1-000, or Honda Fit OEM 0.25mm oversize pistons, PN: 13020-RB7-Z00, or Fast Forward 0.25mm oversize pistons, PN: FF800-110, may be used." In GCR section 9.1.1.B.14.e.2, change as follows: "a. Maximum standard piston diameter, measured at a point 16mm from the bottom of the skirt: 73.240mm (2.8834 2.8835 inches). b. Centerline of wrist pin to crown maximum: 26.21mm (1.032 inches). c. Maximum overall height from skirt to crown edge: 47.80mm (1.882 inches).
Show 13 more lines
d. Minimum weight: 198.0 grams (6.984 ounces). e. Minimum weight of piston pin: 66 grams (2.25 ounces). f. Combined minimum weight of piston, piston pin and connecting rod: 543.5 grams (18.85 ounces). g. Combined minimum weight of piston, wrist pin, and circlips: 267 grams (9.418 ounces). h. Centerline of wrist pin to crown edge: 26.289mm (1.035 inches). i. Ring groove widths: Top ring groove: 1.003mm (0.0395 inches). Middle ring groove: 1.016mm (0.0400 inches). Oil ring groove: 1.981mm (0.0780 inches). j. Ring groove distance from wrist pin center to bottom of groove: Top ring groove: 19.63mm (0.7730 inches). Middle ring groove: 15.29mm (0.6020 inches). Oil ring groove: 10.91mm (0.4295 inches)."
slowerEP Triumph GT6 switches to three Weber 40 DCOE carbs with 28mm chokes, weight rises 50 lbs to 1990.
As printed in Fastrack
In EP Spec Lines, make the following changes in the "Triumph GT6" spec line: Carburetor No. & Type: (2): "1.5” 1.75" Auto-type carburetor(s)" Notes: "Two (2) 1.75” auto-type carburetors @ 1940 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive."
STL Request to Remove Miata Hubs from General category
wordingSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
As printed in Fastrack
In GCR, Section 9.1.4.M.18., change as follows: "18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."
EP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line
cars addedF Production now allows GT-Lite cars meeting Appendix N specifications to compete, effective 2025-01-01.
As printed in Fastrack
“(Effective January 1, 2026) (Effective January 1, 2025)." Any GT-Lite (GTL) car meeting all of the requirements of Appendix N GT-LITE CATEGORY SPECIFICATIONS for inclusion into F PRODUCTION" may compete in the F-Production class. For GTL cars competing in FP, the level of preparation and modifications will be determined by Appendix N and not by PCS 9.1.5.”
cars addedFP GTL Volkswagen Jetta Mark IV 4dr FWD 98.2 wheelbase newly classified.
As printed in Fastrack
In FP Spec Lines, Appendix N, GTL-FP Cars - Volkswagen, classify Jetta Mark - IV as follows: GTL-FP Cars - VOLKSWAGEN Model Years Body Style Drive-line Wheelbase (in) Notes Jetta Mark - IV 4dr FWD 98.2
inductionFP Spec Lines option: carburettor chokes permitted as alternative to SIR, same size as listed SIR.
As printed in Fastrack
In FP Spec Lines, Appendix N: L.9, Fuel Injection System, add the following: "As an option, induction system “Chokes” may be used where a SIR is required. Said chokes shall be fitted to each barrel of carburetor/throttle body and all airflow into engine must pass through them. Choke size will be the same as listed SIR unless noted."
FF Formula F Proposal to Invite Older Cars Via a Tire Rule Change
fasterFF allows older cars with rocker arm or outboard suspension to use bias ply slicks or VFF tires instead of radials.
As printed in Fastrack
In FF, GCR section 9.1.1.B.10.e, change as follows: "Formula F shall be limited to the following tires (front tires may not be used as rears): Dries: Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13 Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13 Wets: Front - Hoosier Wet or W3 Radial 44421 185/60R13 Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Show 12 more lines
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at least one chassis end may use the following tires: Dries: Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick Wets: Radial wets listed above or Front - Hoosier 44165 135/545-13 VFF Rear - Hoosier 44170 165/580-13 VFF Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."
fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.
As printed in Fastrack
In HP Spec Lines "Ford Festiva (88-93)" change as follows: Weight: "1700 1600 *1743 1640 **1785 1680" Notes: "Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."
FP Request to Lower Ford Festiva Minimum Weight to 1600 LBS
fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.
As printed in Fastrack
In HP Spec Lines "Ford Festiva (88-93)" change as follows: Weight: "1700 1600 *1743 1640 **1785 1680" Notes: "Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."
unclearSTL Mazda MX5 Challenge minimum weight now references GCR 9.1.7.1 instead of 2500 lbs; spec components removed, only alternative tires allowed.
As printed in Fastrack
In STL Spec Lines, Table B, Mazda Spec MX5 Challenge, change as follows: Minimum Weight: "2500 See 9.1.7.1." Notes: "Mazda MX5 Challenge car must utilize the following components: Roush CNC cylinder head 0000-01-5300,Mahle standard or +0.005 0000-01-5310, OEM camshaft, 11:1 compression ratio, header 0000-06-5407-NC, exhaust 0000-06-5427-NC, cold air intake 0000- 06-5150-KT, ECU flash 0000-01-5379, Pagid front brake pads 0000-03-5104-SP or endurance pads 0000-03- 5104-EN, Pagid rear brake pads 0000-03-5114-SP or endurance pads 0000-03-5114-EN, Penske front shock 0000-04-5291-SA, Penske rear shock 0000-04-5292-SA, Penske rear mount kit 0000-04-5358, Front mount kit 0000-04-5359, Front offset bushing 0000-04-5407-NC, Eibach front springs 0000-04-9700-08, Eibach rear springs 0000-04-9400-07, Eibach helper springs 0000-04-
Show 5 more lines
9926, Eibach front sway bar 0000-04-5306-FT, Eibach rear sway bar 0000-04-5306-RR, Interior finish panels 0000-07-5822, C&R radiator/oil cooler assembly 0000-01-5504-CR, Oil cooler adapter and lines 0000-01-5511-KT, ACT clutch 0000-02-5004-G6, wheels 17x8 #0000-04-5706-GM, # 0000- 04-5706-SL, and Toyo RR 235-40-17 dry, Toyo RA1 235-40-17 wet. Alternative tires on 17x7 wheels per STL rules. No other Super Touring modifications or allowances permitted except as noted in this spec line. Must conform completely to GCR 9.1.7.1, except alternative tires (only) per STL regs allowed."
Applies to Mazda Miata on this page: Jared Korth, Ricardo Arruda, Gavin Wardle, Ryan Gutile, Bryce Johnson, Andy Chittum, Adrian Comstock
tyres & wheelsFF adds rocker arm and outboard suspension cars optional bias ply and VFF tires; removes front-as-rear rule, adds mixing restrictions.
As printed in Fastrack
In FF, GCR section 9.1.1.B.10.e, change as follows: "Formula F shall be limited to the following tires (front tires may not be used as rears): Dries: Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13 Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13 Wets: Front - Hoosier Wet or W3 Radial 44421 185/60R13 Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Show 16 more lines
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at least one chassis end may use the following tires: Dries: Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick or Hoosier 44165 135/545-13 VFF Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick or Hoosier 44170 165/580-13 VFF Wets: Radial wets or VFF tires listed above or Front - Hoosier 44165 135/545-13 VFF Rear - Hoosier 44170 165/580-13 VFF Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."
EP Base Weight Adjustment for H-Production X1/9 Spec Lines
wordingEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.
As printed in Fastrack
In GCR, Section 9.1.5.E., change as follows: 9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished." 9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must remain stock (tolerance of +/-.25mm)."
wordingEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.
As printed in Fastrack
In GCR, Section 9.1.5.E., change as follows: 9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished." 9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must remain stock (tolerance of +/-.25mm)."
slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".
As printed in Fastrack
In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."
slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".
As printed in Fastrack
In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."
slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".
As printed in Fastrack
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following changes to the Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".
As printed in Fastrack
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following changes to the Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
wordingFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.
As printed in Fastrack
In FP Spec Lines, make the following spec line correction: "Volkswagen Rabbit (Includes Convertible Cabriolet)" In HP Spec Lines, make the following spec line correction: "Volkswagen Rabbit 1588 (Includes Cabriolet)" "Volkswagen Rabbit 1715 (Includes Cabriolet)" "Volkswagen Rabbit 1780 (Includes Cabriolet)"
wordingFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.
As printed in Fastrack
In FP Spec Lines, make the following spec line correction: "Volkswagen Rabbit (Includes Convertible Cabriolet)" In HP Spec Lines, make the following spec line correction: "Volkswagen Rabbit 1588 (Includes Cabriolet)" "Volkswagen Rabbit 1715 (Includes Cabriolet)" "Volkswagen Rabbit 1780 (Includes Cabriolet)"
wordingEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.
As printed in Fastrack
In GCR, Section 9.1.5.E.7., change as follows: "e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear disc brakes under this rule. When converting from rear drum brakes to rear disc brakes: 1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on the vehicle’s spec line. 2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock
Show 3 more lines
from converting to rear disc brakes under this rule. 3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes as stock from converting to rear disc brakes under this rule."
wordingEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.
As printed in Fastrack
In GCR, Section 9.1.5.E.7., change as follows: "e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear disc brakes under this rule. When converting from rear drum brakes to rear disc brakes: 1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on the vehicle’s spec line. 2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock
Show 3 more lines
from converting to rear disc brakes under this rule. 3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes as stock from converting to rear disc brakes under this rule."
unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.
As printed in Fastrack
In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes: "Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."
unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.
As printed in Fastrack
In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes: "Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."
wordingFF clarifies alternative tire eligibility for cars homologated 1989 or earlier with rocker arm or outboard suspension on all four corners.
As printed in Fastrack
In FF, GCR section 9.1.1.B.10.e, change as follows: "Alternatively, Formula F cars with rocker arm suspension (e.g., 1987-90 Reynard, Swift DB1,) and/or outboard suspension on at least one chassis end homologated in 1989 or earlier with any combination of rocker arm or outboard suspension on all four corners (e.g., 1987 – 1990 Reynard, Swift DB1) may use the following alternative tires. Note: This rule is intended to allow older cars with the described suspension design to use the alternative tires. It is not to be exploited by modifying cars with push-rods or pull-rods to meet the above requirements or by modifying either end of older cars to push- or pull-rod suspension to be eligible to run the alternative tires. Cars that were homologated in 1989 or earlier with push- or pull-rod suspension on no more than two corners may seek approval to run the alternative tire by utilizing the compliance process outlined in GCR section 8.1.4."
EP Request to Update E30 BMW Throttle Body Diameter Verbiage
unclearFP Fiat X1/9 gains dual carburetor options with 28mm side-draft alternates and revised valve/transmission specs.
As printed in Fastrack
In FP Spec Lines, change as follows: Fiat X-1/9 & Bertone 1300: "(1) Weber 32 DMTR or DATRA/100 w/32mm bores (1) 40 DCNF w/32mm choke(s) (2) auto-type side-draft w/28mm choke(s) on I.R. manifold Orientation of the alternate carburetor is unrestricted. The alternate carb adapter may not be thicker than 1.25”. The adapter may have a bore larger than the throttle bore of the approved alternate carburetor. Valve Size: (I) 35.5/(1.40) (E) 31.3/(1.23)30.5/(1.20) (E) 1.23
Show 10 more lines
Trans. Speeds: 5" Fiat X-1/9 & Bertone: "Fuel Injection (1) 34 DMTR, (1) 36 DCNF w/34mm choke(s), or (1) 40DCNF w/34mm choke(s) (1) 36 or 40 DCNF w/34mm choke(s) (2) auto-type side-draft w/28mm choke(s) on I.R. manifold Orientation of the alternate carburetor is unrestricted. The alternate carb adapter may not be thicker than 1.25”. The adapter may have a bore larger than the throttle bore of the approved alternate carburetor. Valve Size: (I) 35.5/(1.40) (E) 33.0/(1.30) Trans. Speeds: 5 or 4"
What the rules allowed changed as listed; this does not say what any particular car ran.