This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
6 laps are left out as timing errors (far too short to be a lap of this track). The rest of those sessions, sectors included, is used.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Pro Formula Mazda
FA
1
1:14.588Greg Labadie
1:14.588Greg Labadie
Elan DP02/Mazda
P
1
1:32.576Jim Devenport
1:32.872Jim Devenport
1:33.972Jim Devenport
171.9Jim Devenport
25.461Jim Devenport
26.606Jim Devenport
40.217Jim Devenport
Swift 016
FA
1
1:35.792Greg Labadie
1:35.792Greg Labadie
1:37.275Greg Labadie
163.8Greg Labadie
26.713Greg Labadie
26.816Greg Labadie
41.822Greg Labadie
Dauntless Stohr
P
2
1:36.516Johnnie Crean
1:36.516Johnnie Crean
1:37.287John Manfroy
160.4John Manfroy
25.956Johnnie Crean
27.257John Manfroy
42.386John Manfroy
Dauntless Stohr
P
1
1:36.516Johnnie Crean
1:36.516Johnnie Crean
1:39.209Johnnie Crean
157.4Johnnie Crean
25.956Johnnie Crean
28.143Johnnie Crean
42.417Johnnie Crean
Dauntless-Stohr P07d
P
1
1:37.287John Manfroy
1:41.818John Manfroy
1:37.287John Manfroy
160.4John Manfroy
26.696John Manfroy
27.257John Manfroy
42.386John Manfroy
Stohr WF1
P
1
1:38.716Kevin Mitz
1:38.716Kevin Mitz
1:39.638Kevin Mitz
155.4Kevin Mitz
26.934Kevin Mitz
28.397Kevin Mitz
43.336Kevin Mitz
Penton Norma M20FC
P
1
1:39.296Joseph Moran
1:39.296Joseph Moran
1:40.832Joseph Moran
149.0Joseph Moran
27.106Joseph Moran
28.111Joseph Moran
43.651Joseph Moran
Swift Db6
FF
2
1:49.259Edward Erlandson
1:55.247Johnnie Crean
1:54.993Johnnie Crean
124.5Johnnie Crean
31.358Johnnie Crean
32.841Johnnie Crean
47.766Edward Erlandson
SWIFT DB-6 Honda
FF
1
1:49.259Edward Erlandson
47.766Edward Erlandson
Swift Db6
FF
1
1:54.993Johnnie Crean
1:55.247Johnnie Crean
1:54.993Johnnie Crean
124.5Johnnie Crean
31.358Johnnie Crean
32.841Johnnie Crean
50.291Johnnie Crean
Piper DL7-Honda
FF
1
1:51.118Eric Poulsen
1:52.044Eric Poulsen
1:51.118Eric Poulsen
114.7Eric Poulsen
30.276Eric Poulsen
31.650Eric Poulsen
48.818Eric Poulsen
SWIFT DB-
FF
1
1:53.098Edward Erlandson
1:53.098Edward Erlandson
1:54.741Edward Erlandson
133.7Edward Erlandson
30.951Edward Erlandson
32.299Edward Erlandson
49.791Edward Erlandson
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
FF Add Fast Forward Part Numbers for Honda Fit Engine
wordingFF Honda Fit engine adds Fast Forward part number alternatives for intake, exhaust, oil system, and scavenge pump components.
As printed in Fastrack
In FC/FF, GCR section 9.1.1.B.14.a.6, change as follows: "For all Honda part numbers in these specifications, superc seding part numbers are considered equivalent. In FC/FF, GCR section 9.1.1.B.14.f.5, change as follows: "Cylinder head breather restrictor must be used as supplied by HPD or Fast Forward, unmodified.: HPD PN: 15262-F21S-A200; Fast Forward PN: FF200-503." In FC/FF, GCR section 9.1.1.B.14.k.2, change as follows: "The upper manifold, air box and throttle body assembly must be used as delivered from Honda, HPD, or Fast Forward as noted below."
Show 35 more lines
In FC/FF, GCR section 9.1.1.B.14.k.2, insert as follows: "a. Intake manifold: HPD PN: 17210-F21S-A210; Fast Forward PN: FF200-201. b. Throttle body: Honda Fit: PN: 16400ZZ5024; HPD PN: 16400ZZ5024; Fast Forward PN: FF200-104. c. Throttle lever: HPD PN: 17330-F21S-A210; Fast Forward PN: FF200-101." In FC/FF, GCR section 9.1.1.B.14.k.3, change as follows: "All gaskets and sensors utilized on the inlet manifold from head to throttle body must be Honda Fit OEM, or HPD supplied or Fast Forward as noted below. a. Gasket In. manifold: HPD PN: 17105-RB0-004, Honda Fit OEM. b. Gasket, EGR chamber cover: HPD PN: 17146-RB0-004, Honda Fit OEM. c. Gasket In. port: HPD PN: 17115-RB0-007, Honda Fit OEM. d. Gasket, restrictor: HPD PN: 17399-F21S-A200, (2 required) HPD; Fast Forward PN: FF200-109. Two required." In FC/FF, GCR section 9.1.1.B.14.k.5, change as follows: "The Honda Fit engine is required to have an HPD supplied air inlet restrictor supplied by HPD or Fast Forward: HPD PN: 17344- F21S-A201; Fast Forward PN: FF200-110, with internal diameter of 30.5mm and thickness of 3.175mm (0.125 inches) correctly installed within the intake system." In FC/FF, GCR section 9.1.1.B.14.m.1, change as follows: "The exhaust manifold must be as supplied by HPD or Fast Forward:, HPD part # PN: 18150-F21S-A200 or # PN: 1818 50-F21S-B200; Fast Forward PN: FF500-001 or PN: FF500-002." In FC/FF, GCR section 9.1.1.B.14.n.1, change as follows: "The oil pan, baffle plate, and scavenge pump filter fittings must be as supplied by HP or Fast Forward as noted below. No modifications are permitted. a. Oil pan: HPD PN: 11200-F21S-A210 or PN: 11200-F21S-C240; Fast Forward PN: FF100-201A or PN: FF100-201B. b. Oil pan baffle plate: HPD PN: 11221-F21S-A210; Fast Forward PN: FF100-202. c. Oil scavenge pump filter fittings (2 required): HPD PN: 15180-F21S-A210; Fast Forward PN: FF100-204." In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows: "The scavenge pump and internal scavenge pump parts must be as supplied from HPD or Fast Forward as noted below." In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows: "b. Rotor outside diameter: HPD 44.400mm (1.748 inches):; Fast Forward 40.640mm (1.600 inches). c. Scavenge pump rotor set: HPD PN: 15450-F21S-A20; Fast Forward PN: FF100-110. d. Oil pump: HPD PN: 15100-F21S-A200; Fast Forward PN: FF100-100A. e. Scavenge pump cartridge: 15111-F21S-A21; Fast Forward PN: FF100-127. f. Scavenge pump port A: HPD PN: 15137-F21S-A20; Fast Forward PN: FF100-101. g. Scavenge pump port B: HPD PN: 15139-F21S-A20; Fast Forward PN: FF100-102. h. Scavenge pump shaft: HPD PN: 15510-F21S-A20; Fast Forward PN: FF100-103. i. Scavenge pump front cover: HPD PN: 15070-F21S-A21; Fast Forward PN: FF100-104."
FA E&O - Correct Pro Formula Mazda spec line dimensional equivalent
fasterFA Pro Formula Mazda maximum bodywork width behind front wheels increases to 51.97 inches.
As printed in Fastrack
In FA Table 2, Pro Formula Mazda spec line, change as follows: "The overall maximum width of the bodywork behind the front wheels shall not exceed 132cm (51.17 51.97 inches)."
FA Add new spec line for MSR Formula Mazda FMzR to Table 2
wordingFF Honda Fit gains Fast Forward FF800-100 oversize piston ring pack option.
As printed in Fastrack
In FF, GCR section 9.1.1.B.14.e.3.a, add the following: "The standard ring pack, PN 13011-RB1-004 (Riken) or 13011-RB1-006 (Nippon), or the oversize ring pack, PN 13021-RB7-Z01 (Riken), or 13021-RB7-Z02 (Nippon), or FF800-100 (Fast Forward), may be used."
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
wordingFF VTEC activation valve must function; EGR blanking plate rule clarified with Fast Forward part numbers.
As printed in Fastrack
In FF, GCR section 9.1.1.B.14.r.1, change as follows: "All emission control devices must be removed and blocked off by the blanking plate provided by HPD or Fast Forward as noted below, except for the VTEC activation valve. The VTEC activation valve must be retained; and it must be functioning. No modifications are permitted. a. EGR Plate: Fast Forward PN: FF200-301. b. EGR Port Cover: Fast Forward PN: FF200-302."
fasterFF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs.
As printed in Fastrack
In FF, GCR section 9.1.1.B.20.A.3, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight." In FC, GCR section 9.1.1.B.20.B.4, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
wordingFF Honda Fit allows Fast Forward 0.25mm oversize pistons PN FF800-110 as alternative; piston diameter spec clarified to 2.8835 inches.
As printed in Fastrack
In FF, GCR section 9.1.1.B.14.e.1, change as follows: "Honda Fit OEM standard size pistons, PN: 13010-RB1-000, or Honda Fit OEM 0.25mm oversize pistons, PN: 13020-RB7-Z00, or Fast Forward 0.25mm oversize pistons, PN: FF800-110, may be used." In GCR section 9.1.1.B.14.e.2, change as follows: "a. Maximum standard piston diameter, measured at a point 16mm from the bottom of the skirt: 73.240mm (2.8834 2.8835 inches). b. Centerline of wrist pin to crown maximum: 26.21mm (1.032 inches). c. Maximum overall height from skirt to crown edge: 47.80mm (1.882 inches).
Show 13 more lines
d. Minimum weight: 198.0 grams (6.984 ounces). e. Minimum weight of piston pin: 66 grams (2.25 ounces). f. Combined minimum weight of piston, piston pin and connecting rod: 543.5 grams (18.85 ounces). g. Combined minimum weight of piston, wrist pin, and circlips: 267 grams (9.418 ounces). h. Centerline of wrist pin to crown edge: 26.289mm (1.035 inches). i. Ring groove widths: Top ring groove: 1.003mm (0.0395 inches). Middle ring groove: 1.016mm (0.0400 inches). Oil ring groove: 1.981mm (0.0780 inches). j. Ring groove distance from wrist pin center to bottom of groove: Top ring groove: 19.63mm (0.7730 inches). Middle ring groove: 15.29mm (0.6020 inches). Oil ring groove: 10.91mm (0.4295 inches)."
wordingPrototype Staudacher and unrestricted engine notes corrected for minimum weight wording.
As printed in Fastrack
In Prototype Engine Table, Spec Line B, change the notes as follows: "Staudacher cars may run 950 lb min. wt. minimum weight with 38.5mm flat plate intake restrictor." In Prototype Engine Table, Spec Line D, change the notes as follows: "No restrictor required at 1150 lb min. wt. minimum weight."
wordingPrototype class renamed from P1 to P, affecting designation throughout rules with no performance changes.
As printed in Fastrack
In Categories and Classes, GCR section 9.1, change as follows: "9.1.8. SPORTS RACING CATEGORY CLASSES A Sports Racing (ASR) Regional Class Prototype 1 (P1)" In Homologation Requirements, GCR section 9.2.2, change as follows: "All Formula, Sports Racing, and P1, and P2 cars must be constructed in strict accordance with the rules and regulations contained in the current GCR unless specifically excepted." In Non-Metallic Wheel/Chassis Construction, GCR section 9.3.37, change as follows:
Show 20 more lines
"Non-metallic wheel construction is prohibited. Non-metallic chassis construction is prohibited, except in ASR, P1, FS and FA." In Appendix B, GCR section 1.4.2.G, change as follows: "It is preferable not to combine GT1, AS, T1, T2, T3, and STU with P1, P2, SRF, FP, HP, or GTL." In Appendix C, GCR section 2.6.G, change as follows: "A 14 or 15 year-old must complete his first SCCA driver school in a car not classed in GT1, GT2, FA, FB, F S, ITR, ASR, P1, P2, or T1." In Appendix E, section 1, change as follows: "Depending on the length and banking of the oval course being used, it is recommended that Regions consider restricting the faster classes (GT1, FA, and P 1) from competition at oval track events." In Sports Racing Category, GCR section 9.1.8.1, change as follows: "The SCCA Sports Racing Category shall be for automobiles which are designed and constructed for road racing competition, offering provisions for a driver and passenger, or a driver alone (single-seater). They shall conform to the following requirements. Sports Racers Cars except SRF & SRF3 homologated prior to 1-1-2014 are eligible to compete as P1 or P2 as long as they meet applicable class rules,; no re-homologation is required." "Single seat Formula car chassis (Ex.: FA, FC, FF, FV) fitted with enclosed bodies (as specified in these rules) may run in a Sports Racing/Prototype Class (ASR, P 1, P2) provided they comply with the requirements of the Classification Specification and GCR Section 9." In Sports Racing Category, GCR section 9.1.8.2, change as follows: "In an effort to control shock/damper technology and cost to a level reasonable for Road Racing, in ASR, P1, and P2, any fluid dampers are allowed with the following restrictions:"
FA Classify FR European Championship car as spec line car in Table 2
fasterFF allows older cars with rocker arm or outboard suspension to use bias ply slicks or VFF tires instead of radials.
As printed in Fastrack
In FF, GCR section 9.1.1.B.10.e, change as follows: "Formula F shall be limited to the following tires (front tires may not be used as rears): Dries: Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13 Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13 Wets: Front - Hoosier Wet or W3 Radial 44421 185/60R13 Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Show 12 more lines
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at least one chassis end may use the following tires: Dries: Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick Wets: Radial wets listed above or Front - Hoosier 44165 135/545-13 VFF Rear - Hoosier 44170 165/580-13 VFF Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."
wordingFA Formula Renault 2.0 (10-17) spec notes clarified: engine sealed, manual compliance required, tire choice unrestricted, no alterations except repairs.
As printed in Fastrack
In FA Table 2, Formula Renault 2.0 (10-17) spec line, change the notes as follows: "Engine must remain sealed. Car must comply with year-specific Formula Renault 2.0 manual, technical regulations, and all applicable bulletins found here:. Competitors must have copies of these materials in their possession and present them upon request. https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/bulletins-techniques/2017, https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/manuel-d-utilisateur/2017. The following exceptions apply: Tire choice is unrestricted. No part of the car may be altered from original Formula Renault 2.0 components, except for necessary repairs that do not affect performance."
wordingClass P adds clarification notes on restrictor requirements, throttle bodies, Mazda 12A engine spec, and P2 auto-based engine rules.
As printed in Fastrack
In P Engine Table, Spec Line D notes, add the following: "No restrictor required at 1150 lbs. minimum weight." In P Engine Table, Spec Line G notes, add the following: "Group CN non-composite chassis with Honda K20A-FD2 may use unrestricted individual throttle bodies at 1500 lbs. minimum weight." In P Table 1, Beasley B2 spec line notes, add the following: "Engine must be Mazda 12A rotary with 40.5mm venturi. Car must comply with all other Prototype requirements." In P Table 1, P2 cars built to 2000cc auto-based specification spec line notes, add the following:
Show 3 more lines
"Car must comply with all other P2 rules applicable to cars using stock production-based four-cylinder automotive engines. Note: Competitors are also free to modify their cars to comply with the general Prototype rules and Engine Table Spec Line H instead."
tyres & wheelsFF adds rocker arm and outboard suspension cars optional bias ply and VFF tires; removes front-as-rear rule, adds mixing restrictions.
As printed in Fastrack
In FF, GCR section 9.1.1.B.10.e, change as follows: "Formula F shall be limited to the following tires (front tires may not be used as rears): Dries: Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13 Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13 Wets: Front - Hoosier Wet or W3 Radial 44421 185/60R13 Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Show 16 more lines
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at least one chassis end may use the following tires: Dries: Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick or Hoosier 44165 135/545-13 VFF Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick or Hoosier 44170 165/580-13 VFF Wets: Radial wets or VFF tires listed above or Front - Hoosier 44165 135/545-13 VFF Rear - Hoosier 44170 165/580-13 VFF Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."
tyres & wheelsFA Ligier JS F3 front tires may be Hoosier 43363 240/580R13 MS, rear 43368 300/590R13 MS.
As printed in Fastrack
In FA Table 2, FR Americas Ligier JS F3 spec line, change the notes as follows: "Engine must be sealed in compliance with FR Americas or prior F3 Americas requirements. Car must comply with FR Americas rules, with the following exception: front tires may be Hoosier P/N 43363, size 240/580R13 in MS compound, and rear tires may be Hoosier P/N 43368, size 300/590R13 in MS compound. Competitors must have current copies of Formula Regional Americas Championship Sporting Regulations, Onroak Automotive Ligier JS F3 Information Manual, and HPD engine-related specifications and instructions in their possession and present them upon request."
P RM 25-05 - Prototype Engine Table A, 2 Cycle Restrictor Change
unclearP class 13B rotary engine restrictor changes to 40mm SIR fuel injection or 41.5mm venturi carburetor.
As printed in Fastrack
Effective 9/1/25 in Prototype Engine Table, Spec Line K, change the restrictor as follows: "40mm SIR with fuel injection or 41.5mm venturi with carburetor"
P Add Radical Cup series Radical SR3 spec line to Table 1
wordingPrototype P2 cars may now run P2 spec or modified Prototype spec in Prototype class; clarified language and added Radical Cup series table.
As printed in Fastrack
Effective 9/1/25, in Prototype, GCR section 9.1.8.B.K, change as follows: "P2 cars may compete in either the Prototype class or the P2 class but must participate in the Prototype class to the extent necessary to qualify for an invitation to the Runoffs in Prototype. P2 cars may be modified to comply with the general Prototype rules and Prototype Engine Table or may continue to run in P2 specification in the Prototype class as permitted in Table 1 below." Table 1 (Spec Line Cars)
A specification table follows in the original; it is not shown here.
FA Re-Consider USF Pro 2000 Car for Formula Atlantic Class
unclearFA MZR gains alternate Noor P/N 0088-8-00 intake manifold with AT Power runners as option to Elan or Mazda Speed Elite.
As printed in Fastrack
In FA, GCR section 9.1.1.2.d, modify as follows: "9. Intake manifold must be unmodified Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT, 1.882” maximum bore diameter at throttle plates. Elan or Mazda Speed equivalent Elite intake manifold may be replaced with unmodified intake Noor P/N 0088-8-00 with intake runners AT Power P/N 13624." "10. Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT intake manifold must use an A aluminum spacer must be used between the intake manifold and cylinder head castings; minimum spacer length is 2.200”."
FF Formula F Alternative Tire Rule Proposed Clarifications
wordingFF clarifies alternative tire eligibility for cars homologated 1989 or earlier with rocker arm or outboard suspension on all four corners.
As printed in Fastrack
In FF, GCR section 9.1.1.B.10.e, change as follows: "Alternatively, Formula F cars with rocker arm suspension (e.g., 1987-90 Reynard, Swift DB1,) and/or outboard suspension on at least one chassis end homologated in 1989 or earlier with any combination of rocker arm or outboard suspension on all four corners (e.g., 1987 – 1990 Reynard, Swift DB1) may use the following alternative tires. Note: This rule is intended to allow older cars with the described suspension design to use the alternative tires. It is not to be exploited by modifying cars with push-rods or pull-rods to meet the above requirements or by modifying either end of older cars to push- or pull-rod suspension to be eligible to run the alternative tires. Cars that were homologated in 1989 or earlier with push- or pull-rod suspension on no more than two corners may seek approval to run the alternative tire by utilizing the compliance process outlined in GCR section 8.1.4."
fasterFA Formula 1000 motorcycle-based engine loses maximum compression ratio 14.5:1 limit.
As printed in Fastrack
In FA Table 2, Formula 1000 spec line, change the Engine as follows: "Motorcycle-based 4-cycle up to 1000cc, maximum compression ratio 14.5:1;. o Otherwise, current FA engine rules apply."
suspension & brakesPrototype carbon-carbon and carbon-ceramic brake rotors now permitted instead of prohibited.
As printed in Fastrack
In Prototype, GCR section 9.1.8.B.F.2, change as follows: "Brake calipers may be ferrous or aluminum alloy. Effective 1/1/2026, carbon-carbon and carbon-ceramic brake rotors are prohibited and rotors must be ferrous. Brake rotor material is unrestricted."
fasterFA Formula 1000 allows carbon fiber external panels, forward-facing gaps, raises floor to 125mm, adds eight 75×125mm rub blocks, expands diffuser to 110cm with 75mm radius transitions.
As printed in Fastrack
In FA Table 2, Formula 1000 spec line, change the Notes as follows: "Car must comply with December 2019 GCR Formula 1000 (FB) Preparation Rules, https://www.scca.com/downloads/48184- gcr-december-2019/download, except as modified by this spec line. The prohibition of using carbon fiber in any external panels or any panels licked by the airstream in Part 3.C of the December 2019 GCR F1000 (FB) Preparation Rules is removed, with the exception that the car's floor pan/undertray must comply with the requirements of Part 2.D of the December 2019 GCR F1000 (FB) Preparation Rules. The prohibition of forward-facing gaps or openings in the bodywork in Part 3.I of the December 2019 GCR F1000 (FB) Preparation Rules is removed. Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is modified as follows: "Between the rear of the front tire and the front of the rear tire, no point on the lower surface of the car (the surface
Show 7 more lines
licked by the air stream) shall be more than 125mm above the plane determined by the reference area designated by the entrant and on a line perpendicular to that reference plane." Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is also modified as follows: "A maximum of eight (8) rub blocks of maximum dimension 75mm by 125mm are allowed anywhere on the lower surface of the chassis and may extend below the reference plane." Part 3.E of the December 2019 GCR F1000 (FB) Preparation Rules is modified as follows: "The radius of transitions between the diffuser sides and adjacent horizontal structures may be up to 75mm. The width of the diffuser, as measured between its sides and above any radiused transitions, may not exceed 110cm in any lateral section." The CRB may require the use of Flat Plate Intake Restrictors at any time."
FA Pro Mazda Classification and Performance Enhancement Proposal
fasterFA Pro Mazda: lower intake manifold now unrestricted, throttle body raised to 80mm, wing height must not exceed 99cm, bodywork width must not exceed 132cm.
As printed in Fastrack
In FA Table 2, Pro Formula Mazda spec line, change the notes as follows: "All current FA rules apply to areas not covered by this spec line. Apex seals unrestricted. Street port or bridge port allowed. Unmodified OEM l Lower intake manifold required unrestricted, upper intake manifold unrestricted. Balance tube not permitted. Fuel injection only. Maximum 70 80mm T throttle B body. The maximum height of the wing and/or endplates shall must not exceed 99cm (38.98 inches). The overall maximum width of the bodywork behind the front wheels shall must not exceed 132cm (51.97 inches)."
What the rules allowed changed as listed; this does not say what any particular car ran.