This track has been raced on 4 configurations (The Circuit, 2.57 mi; 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
5 laps are left out as timing errors (far too short to be a lap of this track). The rest of those sessions, sectors included, is used.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Formula Enterprise
FE2
1
1:12.402Blake Pigeon
1:12.402Blake Pigeon
SCCA Ent FE2
FE2
7
1:13.988John Yeatman
1:13.988John Yeatman
1:39.712Paul Marino
156.6Paul Marino
27.234Paul Marino
28.582Paul Marino
43.028Jon McClintock
SCCA Ent FE2 (2007)
FE2
1
1:13.988John Yeatman
1:13.988John Yeatman
SCCA Ent FE2 (2010)
FE2
1
1:14.003Thomas W Burt
1:14.003Thomas W Burt
SCCA Ent FE2
FE2
5
1:39.265Jon McClintock
1:39.265Jon McClintock
1:39.712Paul Marino
156.6Paul Marino
27.234Paul Marino
28.582Paul Marino
43.028Jon McClintock
Chevrolet
GTX
2
1:49.569Bob Blizzard
124.8Michael Arnheiter
29.869Bob Blizzard
31.704Bob Blizzard
47.478Bob Blizzard
Chevrolet
GTX
1
1:49.569Bob Blizzard
124.2Bob Blizzard
29.869Bob Blizzard
31.704Bob Blizzard
47.478Bob Blizzard
Chevrolet Camero
GTX
1
1:59.339Michael Arnheiter
124.8Michael Arnheiter
32.354Michael Arnheiter
33.705Michael Arnheiter
50.741Michael Arnheiter
Ford Mustang GT4
GTX
1
1:49.596Rob Scholl
1:49.596Rob Scholl
116.4Rob Scholl
30.070Rob Scholl
31.820Rob Scholl
46.910Rob Scholl
Porsche 981 Cayman
GTX
1
1:54.892Moze Cowper
1:54.892Moze Cowper
1:55.330Moze Cowper
146.0Moze Cowper
31.377Moze Cowper
32.983Moze Cowper
49.706Moze Cowper
Mazda RX-7
FP
1
1:55.440Michael Lewis
1:56.121Michael Lewis
1:55.440Michael Lewis
128.8Michael Lewis
31.255Michael Lewis
33.299Michael Lewis
50.847Michael Lewis
Nissan Sentra SE-R
FP
1
1:55.722Brian Linn
1:57.239Brian Linn
1:55.722Brian Linn
128.3Brian Linn
31.416Brian Linn
33.400Brian Linn
50.478Brian Linn
Volkswagen GTI
FP
1
1:56.016Tim Linerud
2:06.156Tim Linerud
93.4Tim Linerud
33.738Tim Linerud
35.656Tim Linerud
55.246Tim Linerud
Mazda MIata
FP
1
1:56.276Steven Powers
1:57.032Steven Powers
1:56.276Steven Powers
134.3Steven Powers
31.570Steven Powers
33.696Steven Powers
50.716Steven Powers
Fiat X 1/9
FP
1
1:59.128Daniel Snow
2:00.398Daniel Snow
1:59.128Daniel Snow
137.8Daniel Snow
31.878Daniel Snow
34.053Daniel Snow
52.221Daniel Snow
Porsche 914-4
FP
1
2:15.932Garey Raymond
2:21.274Garey Raymond
2:15.932Garey Raymond
84.8Garey Raymond
37.237Garey Raymond
39.091Garey Raymond
59.604Garey Raymond
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
GTX Please classify Fields Cardinal V8
#33784 from James Rogersn · Rule change · TB 23-05 (2023-05 Fastrack)
neutralFields Cardinal V8 classified in GT1 with Ford V8 engine, 4.9L displacement, 2100 lbs minimum weight.
In GT Spec Lines, GT1 Cars - Fields Cardinal, classify Fields Cardinal V8 as follows: GT1 Cars – Fields Cardinal Model Years Body Style Drive- line Wheel- base (in) Notes Fields Cardinal V8 2023 2 Dr. RWD 92.0 Roll Cage MUST be modified to comply with
Show 6 more lines
GCR Section 9.4. In GT Spec Lines, GT1Engines - classify Ford V8 as follows: GT1 Engines - Ford Engine Family Engine Type Bore x
A specification table follows in the original; it is not shown here.
FP Classification Request for 1978 Toyota Celica
#34097 from Bob Pharr · Rule change · TB 23-05 (2023-05 Fastrack)
neutralFord Fiesta HP and Chevrolet Sonic FP model year ranges extended from 2016 to 2019.
In HP, adjust model years of the "Ford Fiesta (11-16)" spec line as follows: "Ford Fiesta (11-16 9)" In FP, adjust model years of the "Chevrolet Sonic (12-16)" spec line as follows: "Chevrolet Sonic (12-16 9)"
GTX Request Ligier LMP3 Classification
#34043 from Alex Kirby · Rule change · TB 23-06 (2023-07 Fastrack)
neutralGTX Ligier LMP3 3.7L NA classified at 2203 lbs with 22 mm restrictor.
In GTX Spec Lines, classify Ligier LMP3 as follows: GTX - MISC Make Model Engine Restrictor (mm) Weight (lbs) Notes Ligier LMP3 3.7L NA 2203
GTX Ligier JSP4 Request
#34173 from Bob Monette · Rule change · TB 23-06 (2023-07 Fastrack)
neutralGTX Ligier JSP4 newly classified as GTX Misc with restrictor and weight specified.
In GTX Spec Lines, classify Ligier JSP4 as follows: GTX - MISC Make Model Engine Restrictor (mm) Weight (lbs) Notes
FP ITC to FP?
#34286 from David Snow · Rule change · TB 23-06 (2023-07 Fastrack)
neutralHP Volkswagen Rabbit Cabriolet 1780 removed; Rabbit 1588 and 1715 reclassified with engine sizes and year ranges specified.
In HP Spec Lines, Volkswagen Rabbit Cabriolet 1780, delete in its entirely: In HP, Spec Lines, Volkswagen Rabbit, change Title as follows: “Volkswagen Rabbit 1588 (includes Cabriolet / convertible)” “Volkswagen Rabbit 1715 (81-84) (excl. conv.)” “Volkswagen Rabbit GTI 1780 (83-84)”
FP Correct Intake Valve Size on 1500cc Midget/Spitfire
#34419 from Production Committee · Rule change · TB 23-06 (2023-05 Fastrack)
neutralFP and HP Sprite, Midget, and Spitfire 1500 intake valve size corrected to 36.6/(1.44).
In FP Spec Lines, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change Intake Valve Size as follows: "(I) 36.65.3/(1.44)" In FP Spec Lines, Triumph Spitfire Mk. IV & 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire Mk. III & IV 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)"
GTX Errors in GTCS Headings and Use of the Terms Category and ClassChange existing GTL and GTA Rules
#34453 from David Gomberg · Rule change · TB 23-12 (2023-12 Fastrack)
neutralGTL spec lines moved to contiguous position with GT2 and GT3; GTA category and spec lines renumbered and moved behind GTL.
from the current (or before) Table of Contents (TOC), to what is shown in the after TOC. GTL spec lines will now be contiguous with GT2 and 3 spec lines. GTA category and spec lines will be moved and renumbered behind GTL. GTA Section will not change but page numbers will, (as shown in Red italics). 9.1.2.F. GT-2, 3, LITE Category Specifications 314 GT2 Cars 327 GT2/ST 341 GT3 Cars 348
#35002 from Adam Achepohl · Rule change · TB 23-12 (2023-12 Fastrack)
neutralEP Porsche 944/924S combines 2.5L and 2.7L variants with new weights: 2250–2415 lbs depending on engine and year.
In EP Spec Lines, delete the Porsche 944/924S 2.5L (2V) (83-88) spec line entirely, and create a new spec line for Porsche 944/924S 2.5L(2V) 2.7L(2V) (83-89) as follows:
A specification table follows in the original; it is not shown here.
FP FP and HP Toyota Corolla
#35030 from Keith Church · Rule change · TB 23-12 (2023-12 Fastrack)
fasterFP Toyota Corolla 2TC loses 43 lbs to 1810; HP Corolla loses 50–52 lbs to 1910–2006.
In FP Spec Lines, Toyota Corolla 2TC (71-74), change weight as follows: "1853 1810" In HP Spec Lines, Toyota Corolla (71-74), change weight as follows: “1960 1910 * 2009 1958 ** 2058 2006”
FP Triumph GT6 Adjustments
#35054 from ANTHONY PARKER · Rule change · TB 23-12 (2023-12 Fastrack)
fasterEP Triumph GT6 minimum weight reduced to 1800 lbs.
In EP Spec Lines, Triumph GT6, change weight as follows: "1830 1800"
In EP spec line, Triumph GT6, make the following change in the Notes section: "Two (2) 1.75” auto-type carburetors @ 1970 40 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive. Three (3) Weber 40mm DCOE w/28mm venturi on individual runner manifold @ 2020 lb."
FP Honda S2000 throttle body
#35272 from Aaron Johnson · Rule change · TB 24-01 (2024-01 Fastrack)
fasterEP Honda S2000 fuel injected throttle body inside diameter increases from 62mm to 64mm.
In EP spec line, Honda S2000, make the following changes to its spec line: Fuel Injected Equipped Throttle Body Inside Diameter: "62 64" Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .500”. An adaptor plate can be used to mount the 62mm throttle body from '00-05 to the '06-09 intake manifold. The adaptor plate can be no more than 1.25" thick, and its bore must not exceed the "Fuel Injected Equipped Throttle Body Inside Diameter" maximum spec of 64mm."
FP Correction within Triumph TR8 Spec Line
#35315 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)
neutralEP Triumph TR8 dry sump allowance moved from carburetor line to notes section.
In EP spec line, Triumph TR8 (78-81), move the "Dry sump allowed" wording to the appropriate location as follows: Carburetor. No. & Type: “Zenith Stromberg carbs or fuel injection. Dry sump is allowed.” Notes: “Comp. Ratio limited to 12.0:1, Valve lift limited to .500”. Dry sump is allowed.”
FP Correction to EP 924S/944 Spec Line
#35317 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)
neutralEP Porsche 944/924S 2.5L and 2.7L weight minimums corrected: 2479cc to 2306/2363 lbs, 2681cc to 2358/2415 lbs.
In EP spec line, Porsche 944/924S 2.5L (2V) / 2.7L (2V) (83-89), change Weight as follows:
A specification table follows in the original; it is not shown here.
fasterGT1, GT2, GT3, GTL, GTX rear spoiler maximum surface area limit of 295.0 square inches removed.
In GCR Section 9.1.2.G (GTA Category Specifications), change as follows: “9.1.2.G.III.I The single-plane rear spoiler must be mounted at an angel angle from 50 to 75 degrees (perpendicular to the ground being 90 degrees) and may not extend beyond the rear bumper when viewed from directly above the rear bumper. Spoilers must be a minimum of .063 aluminum or Lexan and may vary in overall height to match the contours of the bodywork. The rear spoiler dimensions shall not exceed 59.0 inches wide by 5.0 inches in height, (measured on the material surface) , or 295.0 square inches total surface area. Braces to prevent spoiler deflection are allowed, but may serve no other purpose.”
fasterHP Honda Civic 1.5 (88-91) weight reduced to 2175 lbs base, 2229 lbs with power adder, 2284 lbs with two.
In HP, make the following weight change: Honda Civic 1.5 (88-91) “2245 2175 *2301 2229 **2357 2284”
GTX GT Direct Injection allowance and rules
#35437 from Grand Touring Committee · Rule change · TB 24-02 (2024-01 Fastrack)
fasterGT1/GT2/GT3/GTL/GTX Direct Injection now permitted if OE, using only OE pump, hoses, injectors.
In GCR, Section 9.1.2.F.7.5.E. change as follows: “Direct Injection is not permitted only if it came OE and must be installed using only OE high pressure pump(s), hard and soft hoses and injectors.”
GTX GT2/3 remove Direction Injection not allowed in Spec line notes
#35439 from Grand Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)
fasterGT2/3 Nissan, Mazda, Mitsubishi 4G93, QR25DE/DD, QE25DE/DD Direct Injection now permitted per 9.1.2.F.7.5.E.
In GT2/3 modify Spec Line notes as follows: GT2: Nissan: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” GT3: Mazda: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” Mitsubishi 4G93: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E. ” Nissan QR25DE/DD 1988cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” Nissan QE25DE/DD 2489cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.”
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
FP GCR Correction - Redundant HP Spec Lines
#35623 from Production Committee · Rule change · TB 24-03 (2024-03 Fastrack)
In HP Spec Lines, delete the following redundant spec lines in their entirety: Spec line #10 - VW Rabbit Cabriolet 1780 Spec line #3 - VW Scirocco 1588 Spec line #4 - VW Scirocco 1780 (8-valve) (83-88) Spec line #5 - VW Scirocco 1588
FP Update FP Protege (01-03) Model Info
#35715 from Production Committee · Rule change · TB 24-03 (2024-03 Fastrack)
neutralFP Mazda Protégé ES (01-03) model designation updated to include /5 variant.
In FP Spec Lines, Mazda Protégé ES (01-03) change vehicle as follows: "Mazda Protégé ES/5 (01-03)"
neutralFP Honda CRX 84-87 can replace plastic front header, rocker skirt, door cap panels with stock-appearance replicas in alternate materials.
In FP spec line "Honda CRX / CRX Si (84-87)", add the following wording to the Notes section: "The plastic OE front header/nose body panel, lower rocker side-skirt, and lower door cap panel can be replaced by a replica, which may be constructed of an alternate material, provided its appearance remains stock."
FP FP data and parity
#35896 from Production Committee · Rule change · TB 24-05 (2024-05 Fastrack)
slowerFP Acura Integra and Honda Civic models now require 55mm Flat Plate Intake Restrictor.
In the following FP spec lines, add the following wording to the Notes section: Acura Integra (90-93) Acura Integra LS (94-01) Acura Integra GSR (92-93) Honda Civic Del Sol VTEC (94-97) Honda Civic Si (99-00) "55mm Flat Plate Intake Restrictor is required."
neutralNissan 300ZX 84-89 classified to EP at 2550 lbs minimum, 2960cc 6-cyl SOHC, fuel injection, 12.0:1 compression limit, 0.500" valve lift limit.
In EP Spec Lines, classify Nissan 300ZX (84-89), as follows:
A specification table follows in the original; it is not shown here.
FP RX7 1993 and Up Request In EP Spec Lines, classify
#36031 from Edward Zabinski · Rule change · TB 24-06 (2024-06 Fastrack)
neutralMazda RX-7 92-97 newly classified EP Prep Level 2 at 2200–2310 lbs with 13B 6-port rotary engine.
Mazda RX-7 (92-97) as follows:
A specification table follows in the original; it is not shown here.
FP Clean-up Multiple EP RX-8 Spec Lines In EP
#36156 from Production Committee · Rule change · TB 24-06 (2024-06 Fastrack)
neutralEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.
Spec Lines, make the following changes to the two Mazda RX-8 spec lines. Remove spec line entirely: Mazda RX-8 (04-11) Remove the wording "alternate": Mazda RX-8 (04-11)(alternate) Spec Mazda (SM/SMX) None.
fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1" In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
FP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line
#37119 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)
fasterEP BMW 325i/is E30 (84-91) weight reduced 50–52 lbs across three spec lines to 2150, 2204, 2258.
In EP SPEC LINES, BMW 325i/is (E30) (84-91), change Weight as follows: "2200 2150 *2255 2204 **2310 2258"
GTX Correct language regarding OEM Areo Devices
#37137 from Christopher Childs · Rule change · TB 25-01 (2025-01 Fastrack)
In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows: "B. Aerodynamic Devices 2. Rear wing c. The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule."
A specification table follows in the original; it is not shown here.
FP Fix Error in Spridget Spec Line
#37437 from Jason Stine · Rule change · TB 25-01 (2025-01 Fastrack)
neutralFP Spridget and Midget 1275cc and 1500cc spec line corrections to bore, stroke, displacement, and valve sizes.
In FP SPEC LINES, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change the following: 1275cc: Bore x Stroke: "68.1x78.4 (2.68x3.09) 70.6x81.3 (2.78x3.20)" Displacement: "(77.78) 1275" Valves IN & EX: "(I) 32.1/(1.26) (E) 28.4/(1.12) (I) 33.3/(1.31) (E) 29.5/(1.16)" 1500cc: Bore x Stroke: "1.1x84.3 73.7x87.4 (2.90x3.44)" Displacement: "1491 (90.95) 1493"
Show 1 more lines
Valves IN & EX: "(I) 36.6/(1.44) (E) 28.7 29.7/(1.17)"
FP Create ruleset that allows GTL cars to run in FP
#37485 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)
neutralF Production now allows GT-Lite cars meeting Appendix N specifications to compete, effective 2025-01-01.
“(Effective January 1, 2026) (Effective January 1, 2025)." Any GT-Lite (GTL) car meeting all of the requirements of Appendix N GT-LITE CATEGORY SPECIFICATIONS for inclusion into F PRODUCTION" may compete in the F-Production class. For GTL cars competing in FP, the level of preparation and modifications will be determined by Appendix N and not by PCS 9.1.5.”
neutralFP GTL Volkswagen Jetta Mark IV 4dr FWD 98.2 wheelbase newly classified.
In FP Spec Lines, Appendix N, GTL-FP Cars - Volkswagen, classify Jetta Mark - IV as follows: GTL-FP Cars - VOLKSWAGEN Model Years Body Style Drive-line Wheelbase (in) Notes Jetta Mark - IV 4dr FWD 98.2
FP GTL/FP consolidation 2025 Rules
#37659 from James Gregorius · Rule change · TB 25-03 (2025-03 Fastrack)
neutralFP Spec Lines option: carburettor chokes permitted as alternative to SIR, same size as listed SIR.
In FP Spec Lines, Appendix N: L.9, Fuel Injection System, add the following: "As an option, induction system “Chokes” may be used where a SIR is required. Said chokes shall be fitted to each barrel of carburetor/throttle body and all airflow into engine must pass through them. Choke size will be the same as listed SIR unless noted."
FP Request for Classification of Chevrolet Spark
#37755 from Kristian Smith · Rule change · TB 25-04 (2025-04 Fastrack)
neutralChevrolet Spark 16-22 classified HP Pre at 1850 lbs minimum weight, fuel injected, 1399 cc.
In HP Spec Lines, classify the Chevrolet Spark (16-22):
A specification table follows in the original; it is not shown here.
FP Request to Lower Ford Festiva Minimum Weight to 1600 LBS
fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.
In HP Spec Lines "Ford Festiva (88-93)" change as follows: Weight: "1700 1600 *1743 1640 **1785 1680" Notes: "Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."
FE2 Driver Safety & Comfort
#37965 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)
neutralFE2 allows driver safety and comfort modifications for disabled drivers with SCCA approval, not transferable to other drivers.
In FE2, GCR section 9.1.1.G.2.E, add the following: "g. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
GTX Request to Classify Porsche GT2 RS Clubsport
#37972 from Paul Fairchild · Rule change · TB 25-05 (2025-05 Fastrack)
neutralGTX Porsche GT2 RS Clubsport classified with factory specifications required at all race events.
In GTX, Classify Porsche GT2 RS Clubsport, as follows: GTX Make Homologation Model Restrictor (mm) Weight (lbs) Notes Porsche GT2 RS Clubsport Must have factory specifications available at all race events
GTX Ligier P3 LS Swap
#38164 from Bart Wolf · Rule change · TB 25-06 (2025-06 Fastrack)
unclearGTX Ligier LMP3 now allows any normally aspirated LS Chevrolet engine.
In GTX Spec Lines, GTX-MISC., Ligier, LMP3, 3.0L, Add to Notes the following: "Allow any normally aspirated LS Chevrolet engine may be used."
FP Base Weight Adjustment for H-Production X1/9 Spec Lines
#38255 from Matthew Brannon · Rule change · TB 25-06 (2025-06 Fastrack)
fasterHP Fiat X-1/9 base weights reduced 50–53 lbs across 1300 and 1500 spec lines.
In HP Spec Lines, change Weight as follows: Fiat X-1/9 & Bertone1500: “1790 1740 *1835 1784 **1880 1827” Fiat X-1/9 1300: “1650 1600 *1691 1640 **1733 1680” Fiat X-1/9 1300: “2060 2010” Fiat X-1/9 1500: “1950 1900”
slowerEP BMW Z4 03-05 restricted to 52mm flat plate intake restrictor.
In EP Spec Lines, BMW Z4 (03-05), add to Notes the following: “52mm Flat Plate Intake Restrictor.”
FP EP Fiat 124 Spider Competition Adjustment Request
#38498 from John Baucom · Rule change · TB 25-07 (2025-07 Fastrack)
fasterEP Fiat 124 Spider 1600 & 2000 weight drops 50 lbs to 2000; carburetors gain 2mm chokes to 36mm.
In EP Spec Lines, Fiat 124 Sport Spider 1600 & 124 Spider 2000, change as follows: Weight: "2050 2000" Carburetor No. & Type: "(2) Weber 40 IDF-40IFI, (2) Solex C40P116, 34 36mm choke(s) req’d, (2) Weber 45DCOE w/ 34 36 mm choke(s) on I.R. manifold or fuel injection."
FE2 FE & FE2 Bubble Tail
#38978 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)
neutralFE and FE2 Enterprises must use bubble tail P/N WM138014; FE2 allows only this configuration.
In FE, GCR section 9.1.1.G.2.F.k, change as follows: "Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."
FP HP Plymouth Arrow spec omission
#38995 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralHP Plymouth Arrow transmission max speeds clarified to 4 or 5.
In HP Spec Lines, Plymouth Arrow (76-80), add the following wording to Trans. Speeds(max): "4 or 5"
FP Add Wheel Diameter to Appendix G
#39008 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP wheel diameter added to Appendix G as absolute maximum specification.
In Appendix G.2.3, change as follows: "Rim width and diameter are is absolute maximums."
FP Add TB ID tolerance to general Prod rules
#39009 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.
In GCR, Section 9.1.5.E., change as follows: 9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished." 9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must remain stock (tolerance of +/-.25mm)."
FP Please Lower Weight of 280Z
#38871 from Matthew Miller · Rule change · TB 25-09 (2025-09 Fastrack)
fasterEP Nissan 280Z minimum weight reduced from 2560 to 2400 lbs.
In EP Spec Lines, Nissan 280Z, change Weight (lbs) as follows: "(Effective 11/1/2025) 2560 2400 *2624 2460 **2688 2520"
FP Miata Weight Adjustment Follow Up
#38949 from Don Tucker · Rule change · TB 25-10 (2025-10 Fastrack)
fasterEP Mazda MX-5 1.8L 90-97 weight reduced to 2125 lbs from 2150 lbs.
In EP Spec Lines, Mazda MX-5 / Miata 1.8L (90-97), Effective 11/1/2025 make the following weight change: "2150 2125"
FP Weight Break for 1098 Midget / Sprite
#38970 from Kendall Jones · Rule change · TB 25-10 (2025-10 Fastrack)
In HP Spec Lines, Austin-Healey Sprite/Midget 1098cc, Effective 11/1/2025make the following weight change: "1630 1550"
FP HP Volvo 142 spec omission
#38994 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".
In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."
FP HP Mini DOHC 1.6
#38996 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following changes to the Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
FP 83-88 FP Scirocco Spec Line Creation
#38997 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralFP Scirocco 83-88 established as spec line with 1733–1803 lbs, 1715–1780 cc SOHC, 40/33 mm valves, Solex carbs or fuel injection.
In FP Spec Lines, classify Volkswagen Scirocco (83-88) as follows:
A specification table follows in the original; it is not shown here.
FP Add to Rabbit description
#39019 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.
In FP Spec Lines, make the following spec line correction: "Volkswagen Rabbit (Includes Convertible Cabriolet)" In HP Spec Lines, make the following spec line correction: "Volkswagen Rabbit 1588 (Includes Cabriolet)" "Volkswagen Rabbit 1715 (Includes Cabriolet)" "Volkswagen Rabbit 1780 (Includes Cabriolet)"
FP Clean-up 9.1.5.E.7e
#39025 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.
In GCR, Section 9.1.5.E.7., change as follows: "e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear disc brakes under this rule. When converting from rear drum brakes to rear disc brakes: 1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on the vehicle’s spec line. 2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock
Show 3 more lines
from converting to rear disc brakes under this rule. 3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes as stock from converting to rear disc brakes under this rule."
FP Add TB size to Ford Mustang (94-98) Spec Line
#39130 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP Ford Mustang (94-98) fuel injected throttle body inside diameter specified at 60.
In EP Spec Lines, Ford Mustang (94-98) add the following to the Fuel Injected Equipped Throttle Body Inside Diameter column: "60"
FP Correct Existing VW Scirocco Spec Line
#39140 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
fasterFP Volkswagen Scirocco: remove two engine variants (1715cc and 1780cc), lighten one variant to 1663 lbs, allow 15×7 wheels instead of 13×7.
In FP Spec Lines, Volkswagen Scirocco, change spec line as follows:
A specification table follows in the original; it is not shown here.
FP TR2 Notes E&O
#39180 from Anthony Parker · Rule change · TB 25-12 (2025-12 Fastrack)
unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.
In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes: "Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."
FP Balance of Power
#39187 from Jim Simaras · Rule change · TB 25-12 (2025-12 Fastrack)
slowerEP BMW Z3 2.5L restrictor reduced 52mm to 50mm, weight increased to 2550 lbs base; five other BMW models get smaller restrictors.
In EP Spec Lines, make the following changes to Restrictors: BMW Z3 2.5L: "52mm 50mm Flat Plate Intake Restrictor" BMW Z3 2.8L (97-00): "55mm 53mm Flat Plate Intake Restrictor" BMW 328i/is E36 (96-99): "58mm 55mm Flat Plate Intake Restrictor" BMW 328i/ci E46 (01-06): "58mm 55mm Flat Plate Intake Restrictor" BMW 325i/is (E46) (01-06): "56mm 53mm Flat Plate Intake Restrictor" BMW 325is M-Technic (1994): "56mm 53mm Flat Plate Intake Restrictor" BMW 325i/is E-36 (92-95): "56mm 53mm Flat Plate Intake Restrictor"
Show 4 more lines
In EP Spec Lines, BMW Z3 2.5L, change Weight as follows: "2500 2550 *2563 2614 **2625 2678"
FP Competition Adjustment Request
#39259 from David Strittmatter · Rule change · TB 25-12 (2025-12 Fastrack)
fasterFP Lancia Scorpion minimum weight drops 80 lbs, to 1950.
In FP Spec Lines, Lancia Scorpion, change Weight as follows: "2030 1950"
FP Factory Roll Bar Removal on VW Convertible
#39268 from Tim Linerud · Rule change · TB 25-12 (2025-12 Fastrack)
neutralFP Volkswagen Rabbit Convertible no longer required to remove factory roll bar.
In FP Spec Line, Volkswagen Rabbit (Includes Convertible), remove the following wording in Notes: "Factory roll bar must be removed on Cabriolet."
GTX Please Consider Adding a Spec Line to GTX Table 4 for the RCR T70
#39470 from Peter Jankovskis · Rule change · TB 26-01 (2026-01 Fastrack)
neutralGTX Misc Table 4 adds RCR T70 Coupe with 2200 lbs minimum weight, no restrictor specified.
In GTX-Misc. Table 4, classify RCR70 Coupe: GTX – MISC. TABLE 4 Make Homologation Model Restrictor
A specification table follows in the original; it is not shown here.
FP Request Toyota 5E Series Engines
#38208 from Scott Schick · Rule change · TB 26-02 (2026-02 Fastrack)
neutralFP class adds Toyota 5E DOHC 1497cc engine, 1900 lbs minimum weight, 23mm SIR induction.
In FP Appendix N, add spec line for the Toyota 5E engine to the "Engines - TOYOTA" section:
A specification table follows in the original; it is not shown here.
FP Request for Toyota 4E Series Engines
#38209 from Scott Schick · Rule change · TB 26-02 (2026-02 Fastrack)
neutralFP Toyota 4E DOHC 1331cc engine added to Appendix N with 1900 lbs minimum weight.
In FP Appendix N, add spec line for the Toyota 4E engine to the "Engines - TOYOTA" section:
A specification table follows in the original; it is not shown here.
FP Dual Carbs for the Fiat X1/9
#39593 from Daniel Snow · Rule change · TB 26-02 (2026-02 Fastrack)
unclearFP Fiat X1/9 gains dual carburetor options with 28mm side-draft alternates and revised valve/transmission specs.
In FP Spec Lines, change as follows: Fiat X-1/9 & Bertone 1300: "(1) Weber 32 DMTR or DATRA/100 w/32mm bores (1) 40 DCNF w/32mm choke(s) (2) auto-type side-draft w/28mm choke(s) on I.R. manifold Orientation of the alternate carburetor is unrestricted. The alternate carb adapter may not be thicker than 1.25”. The adapter may have a bore larger than the throttle bore of the approved alternate carburetor. Valve Size: (I) 35.5/(1.40) (E) 31.3/(1.23)30.5/(1.20) (E) 1.23
Show 10 more lines
Trans. Speeds: 5" Fiat X-1/9 & Bertone: "Fuel Injection (1) 34 DMTR, (1) 36 DCNF w/34mm choke(s), or (1) 40DCNF w/34mm choke(s) (1) 36 or 40 DCNF w/34mm choke(s) (2) auto-type side-draft w/28mm choke(s) on I.R. manifold Orientation of the alternate carburetor is unrestricted. The alternate carb adapter may not be thicker than 1.25”. The adapter may have a bore larger than the throttle bore of the approved alternate carburetor. Valve Size: (I) 35.5/(1.40) (E) 33.0/(1.30) Trans. Speeds: 5 or 4"
What the rules allowed changed as listed; this does not say what any particular car ran.