This track has been raced on 2 configurations (The Circuit, 2.57 mi; 2.92 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One run is left out as not that car's own laps (far quicker than the car managed in any other session and than anyone else in its class all week; usually a swapped transponder): Thomas Lepper in Cal Club 2026 Grp 1 EP FP HP B-Spec Race 1 (1:42.146; the car's best in any other session was 2:12.311 and the rest of the class's best all week 2:09.353).
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
MG Midget
HP
4
1:40.295Bill Okell
2:04.965Brian Linn
2:03.082Lee Fleming
126.2Lee Fleming
27.543Bill Okell
28.857Bill Okell
43.861Bill Okell
Mazda RX-3
STU
1
1:50.913Tony Rivera
1:50.913Tony Rivera
1:52.737Tony Rivera
135.2Tony Rivera
30.415Tony Rivera
32.456Tony Rivera
47.999Tony Rivera
Mazda Miata
STU
1
1:51.602Whitfield Gregg
2:02.264Whitfield Gregg
2:01.538Whitfield Gregg
116.3Whitfield Gregg
30.652Whitfield Gregg
32.263Whitfield Gregg
48.687Whitfield Gregg
BMW M3
STU
1
1:52.380Wilson Powell
1:55.401Wilson Powell
1:53.843Wilson Powell
102.6Wilson Powell
30.577Wilson Powell
32.372Wilson Powell
49.215Wilson Powell
Honda S2000
STU
1
1:53.640Rylan Hazelton
1:55.834Rylan Hazelton
1:53.640Rylan Hazelton
134.8Rylan Hazelton
30.582Rylan Hazelton
32.779Rylan Hazelton
49.779Rylan Hazelton
BMW 330
STU
1
1:56.492Sean Lovett
1:56.492Sean Lovett
1:57.049Sean Lovett
133.7Sean Lovett
31.816Sean Lovett
33.669Sean Lovett
50.941Sean Lovett
Nissan 300ZX
STU
1
1:59.183James Slechta
1:59.183James Slechta
2:00.458James Slechta
132.0James Slechta
32.882James Slechta
34.528James Slechta
51.773James Slechta
Mazda MX-5
STU
2
1:59.707Oscar Jackson
2:04.115Dale Shoemaker
1:59.707Oscar Jackson
125.9Dale Shoemaker
32.339Oscar Jackson
34.219Oscar Jackson
52.330Oscar Jackson
Mazda RX-7
STU
1
2:00.248Michael Lewis
2:00.248Michael Lewis
130.4Michael Lewis
32.729Michael Lewis
34.570Michael Lewis
52.880Michael Lewis
Toyota Yaris
B-Spec/HP
2
2:08.224Bobby Beyer
2:10.513Joseph Gersch
2:08.224Bobby Beyer
118.3Joseph Gersch
34.660Bobby Beyer
37.206Bobby Beyer
56.144Bobby Beyer
Mini Cooper
B-Spec/HP
3
2:09.238Tom Tuttle
2:09.353Trenton Kramer
2:09.238Tom Tuttle
121.5Trenton Kramer
34.631Tom Tuttle
37.301Trenton Kramer
56.479Tom Tuttle
Mazda 2
B-Spec
3
2:10.149Ali Naimi
2:11.287Ali Naimi
2:10.149Ali Naimi
117.2Ali Naimi
34.986Ali Naimi
37.336Ali Naimi
57.011Ali Naimi
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
B-Spec BOP Adjustment for Yaris iA, 2020+ Versa, and 07-08 Honda Fit
#35382 from Matt Wolfe · Rule change · TB 24-03 (2024-03 Fastrack)
fasterB-Spec Honda Fit 07-08 loses 125 lbs to 2400; Versa S 2020+ loses 150 lbs to 2550; Yaris iA 16-20 loses 250 lbs to 2450.
In B-Spec Spec Lines, Honda Fit (07-08), change as follows: Min weight: "2525 2400" Notes: "Any Cold Air Intake Package allowed (any manufacturer). This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Honda Fit (07-08) Automatic, change as follows: Min weight: "2525 2400" Add to Notes: "Any Cold Air Intake Package allowed (any manufacturer). This configuration is not currently eligible for Runoffs
Show 12 more lines
competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Nissan Versa S (2020-), change as follows: Min weight: "2700 2550" Add to Notes: "This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Toyota/Scion IA Sedan (16-20), change as follows: Min weight: 2700 2450" Add to Notes: "This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted."
neutralSTU Mini Cooper S SC: alternate LEAP OMICRON hood scoop LEP-OMICRON3 permitted.
In STU Spec Lines, Mini Cooper S SC with Minimum Weight 1900 and 2100, add to Notes: "Alternate LEAP OMICRON hood scoop part # LEP-OMICRON3 is permitted."
neutralB-Spec Honda Fit 07-08 rear sway bar part number changed to Progress #62.1060.
In B-Spec Spec Lines, Honda Fit (07-08) Automatic, change Notes as follows: "Allow rear sway bar Progress # 62.1061 0." In B-Spec Spec Lines, Honda Fit (07-08), add to Notes the following: "Allow rear sway bar Progress # 62.1060."
HP GCR Correction - Redundant HP Spec Lines
#35623 from Production Committee · Rule change · TB 24-03 (2024-03 Fastrack)
In HP Spec Lines, delete the following redundant spec lines in their entirety: Spec line #10 - VW Rabbit Cabriolet 1780 Spec line #3 - VW Scirocco 1588 Spec line #4 - VW Scirocco 1780 (8-valve) (83-88) Spec line #5 - VW Scirocco 1588
B-Spec Change restrictor from 30mm to 31mm (2015+ Honda Fit) and add 50#
#34857 from Matt Downing · Rule change · TB 24-04 (2024-04 Fastrack)
fasterB-Spec Honda Fit MT 2015-19 restrictor increases 30mm to 31mm, weight rises 2525 to 2550 lbs.
In B-Spec Spec Lines, Honda Fit MT (15-19), change as follows: Weight: ""2525 2550" Notes: "30 31mm" In B-Spec Spec Lines, Honda Fit MT (15-19), change as follows: Weight: ""2525 2550" Notes: "30 31mm"
B-Spec Wheel Offset and Spacer Revision
#35466 from Kent Carter · Rule change · TB 24-04 (2024-04 Fastrack)
fasterB-Spec and C-Spec now permit wheels of any offset if tire doesn't protrude beyond fender; spacers allowed with differing left-right offsets per axle.
In GCR, Section 9.1.10.E.8., change as follows: "Wheels: All wheels shall be one-piece metal castings or metal two piece welded. Wheels of any offset are permitted provided the tire tread (the portion of the tire that contacts the ground) does not protrude beyond the fender opening when viewed from the top perpendicular to the ground. Wheel spacers and aftermarket wheel studs/bolts are permitted. Wheel bolts may be replaced with studs and nuts. Total offset must be the same left to right for an individual axle but may differ from front to rear. For B-Spec Required wheel/rim diameter is fifteen inches (15”). Maximum wheel/rim width is seven inches (7”). Minimum Wheel/rim weight shall be 13 lbs. For C-Spec Required wheel/ rim diameter is seventeen inches (17”). Maximum wheel/rim width is eight inches (8”). Minimum
Show 3 more lines
Wheel/rim weight shall be 17 lbs. All wheels shall be one-piece metal castings or metal two piece welded. All four wheels must be the same dimensional offset. Aftermarket wheel studs and/or wheel bolts are allowed. Wheel bolts may be replaced with studs and nuts. Wheel spacers are allowed, the same thickness spacer must be used on all four corners. "
neutralB-Spec Mini Cooper Countryman R60, Paceman R61, and Nissan Versa 1797cc spec lines expire 1/1/2025 unless appealed by 12/1/2024.
In B-Spec Spec Lines, Mini Cooper Countryman (R60) (11-16), add to Notes the following: ”**This Spec line will expire 1/1/2025 unless an appeal is filed on or before 12/1/2024.**” In B-Spec Spec Lines, Mini Cooper Paceman (R61) (11-16), add to Notes the following: ”**This Spec line will expire 1/1/2025 unless an appeal is filed on or before 12/1/2024.** ” In B-Spec Spec Lines, Nissan Versa (07-11) with 1797cc engine, add to Notes the following: ”**This Spec line will expire 1/1/2025 unless an appeal is filed on or before 12/1/2024.** ”
Applies to Mini Cooper on this page: Trenton Kramer, Thomas Lepper
B-Spec Delete trim levels/update language for spec lines
neutralB-Spec model descriptions standardized: trim levels and door count designations removed or replaced with body style wording.
In B-Spec Spec Lines, change Model description as follows: "Chevrolet Sonic 4dr Sedan MT (12-19)" "Chevrolet Sonic 4dr Sedan AT (12-19)" "Chevrolet Sonic 5dr Hatch Hatchback MT (12-19)" "Chevrolet Sonic 5dr Hatch Hatchback AT (12-19)" "Ford Fiesta 5dr Hatchback (11-19)" "Ford Fiesta 4dr Sedan (11-19)" "Honda Fit MT (07-08)"
Show 7 more lines
"Honda Fit Automatic AT (07-08)" "Honda Fit MT (09-14)" "Hyundai Accent GS Hatchback (12-19)" "Kia Rio 5-door/LX Hatchback (12-19)" "Nissan Versa S (2020-)" "Toyota Yaris Hatchback (07-11)" "Toyota Yaris Hatchback (12-18)"
neutralHP Honda CRX/Si 84-87 plastic panels can be replaced with replica alternate material if stock appearance maintained.
In HP spec line "Honda CRX/Si (84-87)", make the following change to the Notes section: "The plastic OE front header/nose body panel, lower rocker side-skirt, and lower door cap panel can be replaced by a replica, which may be constructed of an alternate material, provided its appearance remains stock."
neutralB-Spec and C-Spec wheels must be same thickness spacers all four corners; wording clarified on offset and protrusion rules.
In GCR, Section 9.1.10.E.8., change as follows: "Wheels: All wheels shall be one-piece metal castings or metal two piece welded. All four wheels must be the same dimensional offset. Any offset is permitted so long as Wheels of any offset are permitted provided the tire tread (the that portion of the tire that contacts the ground) does may not protrude beyond the fender opening when viewed from the top perpendicular to the ground. Wheel spacers and aA ftermarket wheel studs/ and or wheel bolts are permitted allowed. Wheel bolts may be replaced with studs and nuts. Wheel spacers are allowed, but must be the same thickness on all four corners.Total offset must be the same left to right for an individual axle but may differ from front to rear. B-Spec Required wheel/rim diameter is fifteen inches (15”). Maximum wheel/rim width is seven inches (7”). Minimum
Show 5 more lines
Wheel/rim weight shall be 13 lbs. C-Spec Required wheel/rim diameter is seventeen inches (17”). Maximum wheel/rim width is eight inches (8”). Minimum Wheel/rim weight shall be 17 lbs. Wheels are permitted any offset provided the tire tread (that portion of the tire that contacts the ground) does not protrude beyond the fender opening when viewed from the top perpendicular to the ground."
neutralB-Spec Mazda2 and multiple Mini Cooper models eliminate redundant sway bar end link part number notes.
B-SPEC Spec Lines, elimination from Notes the following: Mazda2 (10-14): "Front sway bar end links adjstbl 0000-04-2202," Mini Cooper Hatchback (R50) MT (02 - 06): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Hatchback (R50) CVT (02 - 06): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper (R56) MT (07-10): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed."
Show 16 more lines
Mini Cooper (R56) AT (07-10): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Clubman (R55) (07 - 10): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper (R56LCI) MT (11-13): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper (R56LCI) AT (11-13): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Countryman (R60) (11-16): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Paceman (R61) (11-16): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Clubman (R55) (11-15): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Coupe (R58) (12-15): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed."
slowerB-Spec Honda Fit 15-19 CVT weight increases to 2550 lbs, restrictor to 31mm.
CVT Spec Line In B-SPEC Spec Lines, Honda Fit CVT (15-19), change as follows: Weight: "2525 2550" Notes: "30 31mm"
HP Clean-up Multiple EP RX-8 Spec Lines In EP
#36156 from Production Committee · Rule change · TB 24-06 (2024-06 Fastrack)
neutralEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.
Spec Lines, make the following changes to the two Mazda RX-8 spec lines. Remove spec line entirely: Mazda RX-8 (04-11) Remove the wording "alternate": Mazda RX-8 (04-11)(alternate) Spec Mazda (SM/SMX) None.
B-Spec Clean up (15-19) Honda Fit MT & CVT Notes Sections
neutralB-Spec Nissan Versa (09-11) spec line expires 1/1/2025 unless appeal filed by 12/1/2024.
In B-Spec Spec Lines, Nissan Versa (09-11), add to notes the following: "**This Spec line will expire 1/1/2025 unless an appeal is filed on or before 12/1/2024.**"
neutralB-Spec Hyundai Accent rear brakes corrected to 10.3 disc; Kia Rio rear brakes corrected to 10.3 disc.
In B-Spec Spec Lines, Hyundai Accent Hatchback (12-19), change brakes as follows: "(R) 9.9 drum or 10.3 drum disc" In B-Spec Spec Lines, Kia Rio Hatchback (12-19), change brakes as follows: "(R) 10.3 drum disc"
neutralB-Spec and C-Spec restricted to Goodyear Eagle RS/RS-R P205/50R15 and 225/45R17 tires respectively; Hankook tires removed; wet/dry mixing prohibited.
In GCR Section 9.1.10.E.7. change as follows: "a. For the remainder of 2023, B-Spec entrants will be allowed to compete on both Hankook and Goodyear Tires. For B- Spec: tires shall be Hankook 205/50R15 C51, Hankook 200/580R15 Z217, P205/50Z R15 Goodyear Eagle RS (Dry tire) Catalog #D4850 or P205/50ZR15 Goodyear Eagle RS-R (Wet tire) Catalog #D4851. Effective 1-1-2024 Hankook Tires will be allowed at regional events only, through 6-30-2024. Effective 7-1-2024 Goodyear is the only legal specified tire allowed in B-spec for all events. Mixing wet and dry tires is not permitted. Tires may not be modified. All B-Spec competitors are required to place two (2) 12-inch or larger “Goodyear” decals on their cars, one on each side of the car above the front tire. C-Spec: Tires shall be 225/45R17. No Mixing of wet and dry tires on the same car is not permitted. Tires must be run unmodified.
Show 1 more lines
b. When using the Hankook wet tire, all cars get a 0.2” lower ride height allowance due to smaller radius of the wet tire."
fasterB-Spec Sonic restrictors increased to 5-6mm, Fit weight cut 50-25 lbs, Mini Cooper weight reduced 45 lbs, various restrictor adjustments.
In B-Spec Spec Lines, change as follows: Chevrolet Sonic Sedan AT Notes: "33 5mm" Chevrolet Sonic Hatchback AT Notes: "34 6mm" Honda Fit AT (07-08) Weight (lbs): "2400 2350" Notes: "Any aftermarket header allowed."
Show 11 more lines
Honda Fit AT (09-14) Weight: "2525 2500" Notes: "Any Cold Air Intake Package allowed (any manufacturer) with a 25lb adder." Honda Fit CVT (15-19) Notes: "31 3mm" Mini Cooper Hatchback (R50) CVT (02-06) Weight (lbs): "2545 2500" Mini Cooper (R56) AT (07-10) Notes: "44 6mm (OE Catalyst) or 40 2mm (Header)" Mini Cooper (R56LCI) AT (11-13) Notes: "43 5mm (OE Catalyst) or 41mm (Header)"
neutralHP Volkswagen Golf and Jetta 85-92 track correction: front 1537mm (60.5in), rear 1529mm (60.2in).
In HP Spec Lines, change Track (F/R)mm/(in.) as follows: Volkswagen Golf (GTI, GT, GL) (85-92): "2 1537/1529 (60.5/60.2)" Volkswagen Jetta (GLI, GL) (85-92): "2 1537/1529 (60.5/60.2)"
B-Spec Require hood pins
#36233 from Frank Schwartz · Rule change · TB 24-08 (2024-08 Fastrack)
neutralB-Spec and C-Spec hood pins change from optional to recommended; factory release cable may be removed if pins used.
In GCR, Section 9.1.10.E.41., change as follows: "Optional Hood Pins may be added to supplement the original hood latch system. All parts of the original hood latch system must remain in the car. Installation of hood pins is recommended but not required. If hood pins are used, the factory release and cable must be removed, but the secondary latch may be retained. Vehicles equipped with plastic release cables may replace them with steel units. The OEM hood release latch may be relocated."
B-Spec Sonic Caliper Pistons
#36238 from Jonathan Wickert · Rule change · TB 24-08 (2024-08 Fastrack)
neutralB-Spec and C-Spec Chevrolet Sonic and Cruze allow Babyface Fabrication brake caliper pistons.
In B-Spec Spec Lines, change Chevrolet Sonic Sedan MT (12-19), add to Notes the following: "Allow Babyface Fabrication brake caliper piston SNC-SS." In B-Spec Spec Lines, change Chevrolet Sonic Sedan AT (12-19), add to Notes the following: "Allow Babyface Fabrication brake caliper piston SNC-SS." In B-Spec Spec Lines, change Chevrolet Sonic Hatchback MT (12-19), add to Notes the following: "Allow Babyface Fabrication brake caliper piston SNC-SS." In B-Spec Spec Lines, change Chevrolet Sonic Hatchback AT (12-19), add to Notes the following: "Allow Babyface Fabrication brake caliper piston SNC-SS."
Show 2 more lines
In C-Spec Spec Lines, change Chevrolet Cruze (2010-16), add to Notes the following: "Allow Babyface Fabrication brake caliper piston CRZ-SS."
STU RWD Turbo Disadvantage
#36255 from David Fiorelli · Rule change · TB 24-08 (2024-08 Fastrack)
fasterSTU RWD turbo cars no longer required to reduce restrictor by 1 mm from table.
In GCR, Section 9.1.4.1.H.3 - Inlet Restrictor (mm) Minimum Weight (lbs) table, change as follows: "RWD cars must reduce restrictor 1 mm from this table"
B-Spec Scion IA/Toyota Yaris/Mazda 2 DY chassis suspension
unclearB-Spec Toyota/Scion IA Sedan 16-20 allows ST Suspension Kit 13275022, requires three Super Tour weekends and OBD-II data submission.
In B-Spec Spec Lines, Toyota/Scion IA Sedan (16-20), change Notes as follows: "38mm FPR. (Effective 11/1/2024) Allow ST Suspension Kit 13275022. This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted."
fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1" In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
fasterHonda Fit AT 07-08 B-Spec and C-Spec: rear sway bar Progress #62.1060 and any cold air intake package now allowed.
In B-Spec Spec Lines, Honda Fit AT 07-08, change Notes as follows: "(Effective 11/1/2024) Allow damper and spring set 51600F23SA100, Damper FR LH 51605F23SA100, Damper FR RH 51606F23SA100, Damper RR 52610F23SA100, Spring adjust asy RR 52691F23SA010. Seat upper FR spring 51688F23SA200, 51402FC4YA00 front helper spring and 51403FC4YA00 front spacer permitted. Front Damper Mount P/N 51920-F23S-A30 is allowed. Allow rear sway bar Progress # 62.1060. Any Cold Air Intake Package allowed (any manufacturer). This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted."
HP Request for Classification of 1989-1994 Suzuki Swift GT 16V Twin
slowerSTU Mini Cooper S SC 1900 restricts to 2.565 diameter pulley; 2100 allows 2.285 diameter pulley.
In STU Spec Lines, Mini Cooper S SC, add to notes: 1900: "Stock supercharger pulley. 2.565 diameter." 2100: "JCW Pulley permitted. May run a 2.285 diameter pulley."
STU Request to Remove Miata Hubs from General category
#37138 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)
neutralSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
In GCR, Section 9.1.4.M.18., change as follows: "18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."
STU BMW N54/N55 Engine Allowance
#37146 from Martin Sarukhanyan · Rule change · TB 24-12 (2024-12 Fastrack)
slowerSTU BMW N54/N55 turbo inlet restrictors now required per GCR definition; turbo swapping prohibited.
"Turbo inlet restrictors designed per GCR Appendix F Technical Glossary definition of “Turbo Inlet Restrictor” may be required; see table 9.1.4.1.H.h.2 3. Swapping of turbochargers between engine makes and models is prohibited. Supercharged cars may be approved on a case-by-case basis; twin turbo engines are allowed on a case-by-case basis only. Contact the Road Racing Technical Office for details. Twin turbo engines may be converted to single turbo using one of the allowed alternate turbos (see 9.1.4.1.H.3 2). Aftermarket turbocharger and supercharger kits will be allowed on a case-by-case basis.
HP MINI Cooper Spec Line Correction - Rear Brake Rotor Diameter
#37176 from Robert Bax · Rule change · TB 24-12 (2024-12 Fastrack)
neutralHP Mini Cooper 02-06 rear brake rotor increases from 239/9.4 mm/in to 259/10.2.
In HP Spec Lines, Mini Cooper (02-06), change Brakes Std.mm/(in.) as follows: "(F) 276/(10.9) Vented Disc (R) 239/(9.4) 259/(10.2) Solid Disc"
Applies to Mini Cooper on this page: Tom Tuttle
B-Spec Remove wheelbase from spec lines and replace with Restrictor
unclearB-Spec and C-Spec cars replace wheelbase spec with induction restrictor (mm) values, effective 2025-01-01.
In B-Spec Spec Lines that are not expiring on 1/1/25, replace Wheelbase as follows: "(Effective 1/1/2025)Wheelbase Restrictor (mm)" In B-Spec Spec Lines, update the value in the spec lines under the Restrictor column as follows effective 1/1/2025: Chevrolet Sonic Sedan MT (12-19): "2525 33" Chevrolet Sonic Sedan AT (12-19): "2525 35" Chevrolet Sonic Hatchback MT (12-19): "2525 34" Chevrolet Sonic Hatchback AT (12-19): "2525 36" Fiat 500 (12-17): "2300"
Show 28 more lines
Ford Fiesta Hatchback (11-19): "2470 39" Ford Fiesta Sedan (11-19): "2470 38" Honda Fit MT (07-08): "2450" Honda Fit AT (07-08): "2450" Honda Fit MT (09-14): "2500" Honda Fit AT (09-14): "2500" Honda Fit MT (15-19): "2530 31" Honda Fit CVT (15-19): "2530 33" Hyundai Accent Hatchback (12-19): "2570 41" Kia Rio Hatchback (12-19): "2570 41" Mazda2 (10-14): "2490" Mini Cooper Hatchback (R50) MT (02-06): "2466" Mini Cooper Hatchback (R50) CVT (02-06): "2466" Mini Cooper (R56) MT (07-10): "2466 44 (OE Catalyst) 40 (Header)" Mini Cooper (R56) AT (07-10): "2466 46 (OE Catalyst 42 (Header)" Mini Cooper Clubman (R55) (07-10): "2547 44 (OE Catalyst) 40 (Header)" Mini Cooper (R56LCI) MT (11-13): "2466 43" Mini Cooper (R56LCI) AT (11-13): "2466 43" Mini Cooper Clubman (R55) (11-15): "2547 42" Mini Cooper Coupe (R58) (12-15): "2466 42" Nissan Micra Cup Cars (Canadian): "2450" Nissan Versa Sedan (2012-2019): "2600" Nissan Versa Hatchback (2012-2019): "2600" Nissan Versa (2020-): "2618 38" Toyota/Scion IA Sedan (16-20): "2570 38" Toyota Yaris Hatchback (07-11): "2461 42" Toyota Yaris Hatchback (12-18): "2510 42" Toyota Yaris Sedan (07-12): "2550 41"
STU Audi 1.8t Wagon STU Table B
#36685 from Mike McLaughlin · Rule change · TB 25-01 (2025-01 Fastrack)
fasterSTU Audi 1.8T wagon deleted; Porsche 944 1800 weight to Chart, turbo inlet restrictor removed.
In STU Spec Lines, Table B: Alternate Vehicle and Engine Requirements, delete Audi/VW 1.8 Turbo in its entirety. In STU Spec Lines, Table B: Alternate Vehicle and Engine Requirements, Porsche 944 w/Max Displacement 1800, change as follows: Weight: "3050 Chart" Notes: "VW/Audi 1.8L 35mm turbo engine permittedinlet restrictor required."
B-Spec Bilstein Rear Shock Request for Hyundai Accent/Kia Rio
#36965 from Alex Ratcliffe · Rule change · TB 25-01 (2025-01 Fastrack)
neutralB-Spec Hyundai Accent and Kia Rio approve Bilstein B8 shock 33-187112 for rear suspension use.
In B-Spec Spec Lines, Hyundai Accent Hatchback (12-19), add to Notes the following: "Bilstein B8 shock 33-187112 approved for use in rear suspension." In B-Spec Spec Lines, Kia Rio Hatchback (12-19), add to Notes the following: "Bilstein B8 shock 33-187112 approved for use in rear suspension."
HP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line
#37119 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)
fasterEP BMW 325i/is E30 (84-91) weight reduced 50–52 lbs across three spec lines to 2150, 2204, 2258.
In EP SPEC LINES, BMW 325i/is (E30) (84-91), change Weight as follows: "2200 2150 *2255 2204 **2310 2258"
HP Request to Update 1988-1991 Civic to Match 1988-1991 CRX
fasterHP Honda Civic 1.5 88-91 weight reduced to 2175 lbs base, 2229 lbs with one asterisk, 2284 lbs with two asterisks.
In HP SPEC LINES, Honda Civic 1.5 (88-91), change Weight as follows: "2245 2175 *2301 2229 **2357 2284"
STU Merger GT3 to STU
#37486 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)
neutralSTU-GT3 reclassified as STU-GT3U effective January 1, 2026.
In STU, Table C, change STU-GT3 charge as follows: "(Effective January 1, 2026) TABLE C: STU-GT3U"
STU GT3 TCR Tire allowance
#37494 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)
slowerSTU GT3 TCR gains 275-width tire option with 100 lb weight penalty, but not in A compound.
In STU, Table C, GT3 TCR, add to Notes the following: "May run DOT approved tire with maximum section width of 275 with 100 pound weight adder. May not run A compound with 275."
B-Spec Remove Redundant Language from Notes Sections
neutralB-Spec Honda Fit AT, Fit CVT, Mazda2, Mini Cooper R50 MT and CVT, Toyota Yaris remove redundant notes language.
In B-Spec Spec Lines, Honda Fit AT (07-08), change Notes as follows: "Allow damper and spring set 51600F23SA100, Damper FR LH 51605F23SA100, Damper FR RH 51606F23SA100, Damper RR 52610F23SA100, Spring adjust asy RR 52691F23SA010. Seat upper FR spring 51688F23SA200, 51402FC4YA00 front helper spring and 51403FC4YA00 front spacer permitted. Front Damper Mount P/N 51920-F23S-A30 is allowed. Allow rear sway bar Progress # 62.1060. Any Cold Air Intake Package allowed (any manufacturer). This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted. Any aftermarket header allowed. Allow rear sway bar Progress # 62.1060. Any Cold Air Intake Package allowed (any manufacturer). This configuration is
Show 25 more lines
not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Honda Fit CVT (15-19), change Notes as follows: "Allow damper FR LH 51605F23SA81, Damper FR RH FR RH 51606F23SA81, Damper RR 52610F23SA80, Spring adjust assy RR 52691F23SA80, Camber Adjuster Comp, Damper 51920F23SA82. Exhaust pipe assy 18300F23SA81, ACG belt (6PK858) 31110FC4YA80. Allow rear sway bar Progress 62.1063. Allow Setrab 50- 119-7612 transmission cooler in addition to OEM." In B-Spec Spec Lines, Mazda2 (10-14), change Notes as follows: "Helper springs F&R 0000-04-9926, Spring spacer F&R 0000-04-9925, Rear sway bar 0000-04-2203-RR or 0000-04- 2312, Modified strut bearing plate 0000-04-2204, Crash bolt set 0000-04-2205, Allow rear torque bar Corksport #Mz2-3-070. Cold air intake Corksport Mz2-6-117-31100 and air duct Mz2-6-120-10 are allowed. Exhaust Header (cat delete) HB.EM 60-404- S-SS, HP-MZD001, or Mazda Motorsports PN 0000- 06-2410 permitted. Powerflex PFR19-1511BX2 rear suspension bushings allowed. Allow Mazda part number 0000-01-2501-CR Radiator. Allow Mazda undertray part number DO8C-56-110A, DO8C-56- 311, DO7A-56-321." In B-Spec Spec Lines, Mini Cooper Hatchback (R50) MT (02-06), change Notes as follows: "Allow KW: Coilover Kit: Variant 2: Gen 1 or KW equivalent, Vorshlag Mini R50/53 Camber Plates & Perches allowed. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Allow rear sway bar Progress #62.0210." In B-Spec Spec Lines, Mini Cooper Hatchback (R50) CVT (02-06), change Notes as follows: "Allow KW: Coilover Kit: Variant 2: Gen 1 or KW equivalent, Vorshlag Mini R50/53 Camber Plates & Perches allowed. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Allow rear sway bar Progress #62.0210.CVT equipped cars allow Setrab 50-119-7612 transmission cooler in addition to OEM." In B-Spec Spec Lines, Toyota Yaris Hatchback (07-11), change Notes as follows: "PTR04-52061 TRD Sport shocks permitted. PTR11-52070 TRD spring kit permitted. Speed sensor may be disconnected. Cold air intake K&N 69-8612TFK is allowed. Rear Swaybar PTR11-52071 is allowed. Any Camber plate is permitted."
Applies to Mini Cooper on this page: Trenton Kramer, Thomas Lepper
Applies to Toyota Yaris on this page: Joseph Gersch
neutralB-Spec removes Mini Cooper Countryman R60, Cooper Paceman R61, and two Nissan Versa generations effective 2/1/25.
In B-Spec Spec Lines, delete the following spec lines effective 2/1/25 in their entirety: "Mini Cooper Countryman (R60) (11-16)" "Cooper Paceman (R61) (11-16)" "Nissan Versa (07-11)" "Nissan Versa (09-11)"
B-Spec Set expiration date for Nissan Micra Cup Cars (Canadian)
neutralB-Spec Nissan Micra Cup Car spec line expires 7/1/25 unless appeal submitted by 6/30/25.
In B-Spec Spec Lines, Nissan Micra Cup Car, add to Notes the following: "This spec line will expire on 7/1/25 unless an appeal is submitted by 6/30/25."
In EP Spec Lines, add to Notes as follows: BMW Z3 2.5LL "(Effective 2/21/2025) 52mm Flat Plate Intake Restrictor is required." BMW Z3 2.8L (97-00): "(Effective 2/21/2025) 55mm Flat Plate Intake Restrictor is required." BMW 328i/is E36 (96-99): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required." BMW 328i/ci E46 (01-06): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required." BMW 325i/is E46 (01-06): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required." BMW 325i/is E-36 (92-95): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required." BMW 325is M-Technic (1994): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."
Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21
HP Request Competition Adjustment to BMW Z3 2.5L
#37120 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)
slowerEP BMW Z3 and 3-series models get smaller intake restrictors: Z3 2.5L to 52mm, Z3 2.8L to 55mm, 328i to 58mm, 325i to 56mm.
In EP Spec Lines, change Notes as follows: BMW Z3 2.5LL "(Effective 3/1/2025) 56mm 52mm Flat Plate Intake Restrictor is required." BMW Z3 2.8L (97-00): "(Effective 3/1/2025) 59mm 55mm Flat Plate Intake Restrictor is required." BMW 328i/is E36 (96-99): "(Effective 3/1/2025) 62mm 58mm Flat Plate Intake Restrictor is required." BMW 328i/ci E46 (01-06): "(Effective 3/1/2025) 62mm 58mm Flat Plate Intake Restrictor is required." BMW 325i/is E46 (01-06): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required." BMW 325i/is E-36 (92-95): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required." BMW 325is M-Technic (1994): "(Effective 3/1/2025) 60mm 56mm Flat Plate Intake Restrictor is required."
HP Interpretation of Production Rules on Mirrors
#37235 from Lawrence Slivinski · Rule change · TB 25-03 (2025-03 Fastrack)
neutralEP, FP, HP: interior or exterior mirrors meeting rule 9.3.36 now permitted.
In GCR, add new rule as Section 9.1.5.E.10.f: "Any interior or exterior mirror(s) that meets rule 9.3.36 may be used."
STU BMW N54/N55 Engine Allowance Follow Up
#37447 from Martin Sarukhanyan · Rule change · TB 25-03 (2025-03 Fastrack)
neutralSTU BMW N54/N55 3.0L classified at Chart +3% minimum weight; N54 twin turbo not allowed.
In STU Spec Lines, Table A, classify BMW N54/N55 as follows: STU Maximum Displacement (cc's) Minimum Weight Notes BMW N54/N55 3.0 Chart +3% (DI) Short blocks, heads, and intakes may be freely swapped within these engine designations. N54 twin turbo not allowed
HP HP Class Adjustments
#37459 from Production Committee · Rule change · TB 25-01 (2025-01 Fastrack)
slowerHP Mazda 2 11-14 base weight up 50 lbs to 2045; all VW 80s models up 50 lbs to 2150 base.
neutralB-Spec Toyota Yaris Hatchback and Sedan may now disconnect speed sensor.
In B-Spec Spec Lines, Toyota Yaris Hatchback (12-18) AND Toyota Yaris Sedan (07-12), add to Notes the following: "Speed sensor may be disconnected."
HP MINI Cooper (07-13) Spec Line Correction: Errors and Omissions
#37560 from Robert Bax · Rule change · TB 25-03 (2025-03 Fastrack)
slowerHP Mini Cooper 07-13 engine corrected to DOHC; valve lift limit reduced to 0.390 inches.
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), change as follows: Engine Type: "4 Cyl SOHC DOHC" Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
fasterB-Spec Honda Fit MT intake now limited to three models with 25lb adder; Mazda2 exhaust headers allowed with up to 50lb adder; Mini Coopers FPR increased 1-2 points; Nissan Versa sedans 40lbs lighter, Yaris models 50lbs lighter.
In B-SPEC Spec Lines, change as follows: Honda Fit MT (09-14): "Any Cold Air Intake Package allowed (any manufacturer) Allow Injen Intake SP1512, K&N Intake 69- 1017TTK, or HPS intake 827-102 with a 25lb adder." Mazda2 (10-14): "Exhaust Header (cat delete) HB.EM 60-404-S-SS, HP-MZD001 allowed with a 50lb adder, or Mazda Motorsports PN 0000- 06-2410 permitted with no weight adder." Mini Cooper (R56) MT (07-10): "44 5 FPR (OE Catalyst)" Mini Cooper (R56) AT (07-10): "46 7 FPR (OE Catalyst)" Mini Cooper Clubman (R55) (07-10): "44 5 FPR (OE Catalyst)"
Show 7 more lines
Mini Cooper (R56LCI) MT (11-13): "43 4 FPR" Mini Cooper (R56LCI) AT (11-13): "45 6 FPR (OE Catalyst)" Mini Cooper Clubman (R55) (11-15): "42 4 FPR" Nissan Versa Sedan (12-19): "2490 2450" "Allow Injen intake SP1906" Nissan Versa Hatchback (12-19): "2490 2450" "Allow Injen intake SP1906" Toyota Yaris Hatchback (12-18): "2400 2350" Toyota Yaris Sedan (07-12): "2400 2350"
fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.
In HP Spec Lines "Ford Festiva (88-93)" change as follows: Weight: "1700 1600 *1743 1640 **1785 1680" Notes: "Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."
slowerB-Spec 07-08 Honda Fit MT minimum weight increases 50 lbs, to 2450.
In B-SPEC Spec Lines, Honda Fit MT (07-08), change as follows: Minimum weight: "2400 2450" Notes: "OEM exhaust manifold required. Primary catalyst may be removed."
B-Spec Add B14 Kit Part # to Honda Fit (07-08) Spec line
neutralHonda Fit 07-08 MT and AT approved for Bilstein B14 kit 47172401 in B-Spec.
In B-SPEC Spec Lines, Honda Fit (07-08) MT, add to Notes the following: "Bilstein B14 kit 4717 → 2401 verified compatible." In B-SPEC Spec Lines, Honda Fit (07-08) AT, add to Notes the following: "Bilstein B14 kit 4717 → 2401 verified compatible."
STU Wheel Size Inconsistency
#38018 from David Fiorelli · Rule change · TB 25-05 (2025-05 Fastrack)
neutralSTU wheel width rules clarified: cars ≤2,850 lbs max 8 inches, cars >2,850 lbs max 9 inches.
In GCR, Section 9.1.4.1.F.1., change as follows: "Wheels may not exceed 18 inches in diameter. or 8.0 inches in width for vehicles 2950 lbs. and under minimum allowed race weight. Vehicles over 2850 minimum allowed race weight may use a 9 inch wide wheel. Cars equal to or less than 2,850 lbs. minimum allowed race weight may not use wheels wider than 8 inches. Cars greater than 2,850 lbs. minimum allowed race weight may not use wheels wider than 9 inches."
STU Table C: STU-GT3U Clarification
#38268 from Club Racing Board · Rule change · TB 25-05 (2025-05 Fastrack)
fasterSTU Spec Line GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tire options clarified with weight adjustments.
In STU Spec Line, Table C: STU-GT3U, change as follows: Minimum Weight: “Current GT3 race weight plus 250 225 pounds” Notes: "DOT approved tire with maximum section width of 245. GT3 cars base wheel is a maximum of 15”x9”. 18”x9” wheels allowd with a 3% weight addition. GT3 cars utilizing 15”x7” wheels are limited to a maximum section width of 225 with a 25 pound weight reduction" "All GT3U (Majors and Runoffs) cars using up to 15"x7" wheels limited to 225 section width tires shall run at current GT3 race weight plus 225lbs. All Gt3U cars shall run a DOT approved tire with a maximum section width of 245. GT3U cars are allowed optional 15"x9" wheels with a 1.5% weight addition or up to 18"x9" wheels with a 3.0% weight addition to the total weight
neutralB-Spec and C-Spec shift linkage/cables no longer prohibited from any modification; approved aftermarket bushings now permitted.
In GCR, Section 9.1.10.E.46. change as follows: "Aftermarket shift knobs are allowed and shift levers mat y be bent or extended, however the shift linkage/cables must remain stock and may not be modified in any way. Approved aftermarket shift linkage bushings are permitted."
STU 2.8-3.2L N/A Engine Allowances
#38007 from Ben Slechta · Rule change · TB 25-07 (2025-07 Fastrack)
unclearSTU 2.8-3.2L N/A engines now allow 245 max tire width; over 3150 lbs may run 275 with 2% weight penalty.
In GCR, Section 9.1.4.G.1, add the following: "A maximum section width of 245 is permitted. Cars over 3150 lbs. may run a 275 tire with a 2% weight adder."
STU 2006-2015 Mazda Miata Intake Manifold
#38422 from German Candelario Candelario · Rule change · TB 25-07 (2025-07 Fastrack)
neutralSTU Mazda MZR may use Goodwin 61-2510 or Gato Performance 31972 intake manifold.
In STU, Table A, Mazda MZR (LF, L3, L5), change Notes as follows: "May use Goodwin Part # 61-2510 or Gato Performance Part #31972 Intake manifold . "
STU Requesting Approval of the JDM Honda h23a
#38489 from Eric Fiest · Rule change · TB 25-07 (2025-07 Fastrack)
neutralSTU Honda JDM H23a added, 2259cc displacement, minimum weight per Chart, must meet ST engine regulations.
In STU, Table B, classify Honda JDM H23a as follows: STU Maximum Displacement (cc's) Minimum Weight Notes Honda JDM H23a 2259 Chart Must meet all ST engine regulations.
slowerEP BMW Z4 03-05 restricted to 52mm flat plate intake restrictor.
In EP Spec Lines, BMW Z4 (03-05), add to Notes the following: “52mm Flat Plate Intake Restrictor.”
HP EP Fiat 124 Spider Competition Adjustment Request
#38498 from John Baucom · Rule change · TB 25-07 (2025-07 Fastrack)
fasterEP Fiat 124 Spider 1600 & 2000 weight drops 50 lbs to 2000; carburetors gain 2mm chokes to 36mm.
In EP Spec Lines, Fiat 124 Sport Spider 1600 & 124 Spider 2000, change as follows: Weight: "2050 2000" Carburetor No. & Type: "(2) Weber 40 IDF-40IFI, (2) Solex C40P116, 34 36mm choke(s) req’d, (2) Weber 45DCOE w/ 34 36 mm choke(s) on I.R. manifold or fuel injection."
B-Spec Disabling 2 Pedal Shutdown
#38354 from Eric Yagel · Rule change · TB 25-08 (2025-08 Fastrack)
neutralB-Spec Honda Fit MT 09-14 two pedal shutdown may be disabled by cutting/de-pinning pin 42 BKSW at main ECU connector.
In B-Spec Spec Lines, Honda Fit MT (09-14), add to Notes the following: "Two pedal shutdown may be disabled by cutting/de-pinning pin 42 (BKSW) at the main ECU connector in the engine bay."
B-Spec Update Honda Fit MT (07-08) Intake Allowance
slowerB-Spec Honda Fit MT 07-08 intake restricted to Injen SP1511 only, from any Cold Air Intake Package.
In B-Spec Spec Lines, Honda Fit MT (07-08), change Notes as follows: "Bilstein B14 kit 47172401 verified compatible. Allow rear sway bar Progress #62.1060. Any Cold Air Intake Package allowed (any manufacturer). Allow Injen Intake SP1511. This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted. OEM exhaust manifold required. Primary catalyst may be removed."
STU STU-TCR Adjustments
#38723 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)
slowerSTU-TCR tire width increases to 275 with weight adder raised from 100 to 150 pounds.
In STU Spec Lines, Table C: STU-GT3U, GT3-TCR, change as follows: Remove the current TCR spec line and add the TCR spec lines from GT3 that are being removed, adding the below to the notes. "DOT approved tire with maximum section width of 245. May run DOT approved tire with maximum section width of 275 with 100 150 pound weight adder. May not run A-compound with 275. STU-TCR spitters and side valance must comply with 9.1.4.D.3.f. STU-TCR chassis ride height must comply with 9.1.4.1.A.1."
STU Lotus Weight Reduction
#38772 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)
fasterSTL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs.
In 9.1.2. GT2/ST Spec Lines, Lotus Evora GT4, change Weight as follows: "2750 2700" In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows: Lotus Elise Cup R: "2300 2250" Lotus Elise SC/ Lotus Exige SC: "2300 2550 2500 2450"
neutralB-Spec and C-Spec: asterisk removed from public road usage note in rule 9.1.10.D.9.
In GCR, Section 9.1.10.D.9, change as follows: "* If car is used on public roads, these items should be replaced, reactivated, rearmed, etc. when not in competition."
STU Lotus Weight Reduction E&O
#38919 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)
fasterSTU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs.
In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows: Lotus Elise SC/ Lotus Exige SC: "2450 2250"
HP HP Plymouth Arrow spec omission
#38995 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralHP Plymouth Arrow transmission max speeds clarified to 4 or 5.
In HP Spec Lines, Plymouth Arrow (76-80), add the following wording to Trans. Speeds(max): "4 or 5"
HP Add Wheel Diameter to Appendix G
#39008 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP wheel diameter added to Appendix G as absolute maximum specification.
In Appendix G.2.3, change as follows: "Rim width and diameter are is absolute maximums."
HP Add TB ID tolerance to general Prod rules
#39009 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.
In GCR, Section 9.1.5.E., change as follows: 9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished." 9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must remain stock (tolerance of +/-.25mm)."
B-Spec Alternate Shift Cable Bushings and Rear Spring Seats
In HP Spec Lines, Austin-Healey Sprite/Midget 1098cc, Effective 11/1/2025make the following weight change: "1630 1550"
HP HP Volvo 142 spec omission
#38994 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".
In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."
HP HP Mini DOHC 1.6
#38996 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following changes to the Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
B-Spec Request to Remove Rear Shock From Spec Line Hyundai Accents/Kia
#39017 from Alex Ratcliffe · Rule change · TB 25-11 (2025-11 Fastrack)
unclearB-Spec Hyundai Accent and Kia Rio remove Bilstein B8 shock 33-187112 rear suspension approval.
In B-Spec Spec Lines, Hyundai Accent Sedan (12-17), change Notes as follows: "Bilstein B8 shock 33- 187112 approved for use in rear suspension." In B-Spec Spec Lines, Kia Rio Sedan (12-17), change Notes as follows: "Bilstein B8 shock 33- 187112 approved for use in rear suspension."
HP Add to Rabbit description
#39019 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.
In FP Spec Lines, make the following spec line correction: "Volkswagen Rabbit (Includes Convertible Cabriolet)" In HP Spec Lines, make the following spec line correction: "Volkswagen Rabbit 1588 (Includes Cabriolet)" "Volkswagen Rabbit 1715 (Includes Cabriolet)" "Volkswagen Rabbit 1780 (Includes Cabriolet)"
HP Clean-up 9.1.5.E.7e
#39025 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.
In GCR, Section 9.1.5.E.7., change as follows: "e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear disc brakes under this rule. When converting from rear drum brakes to rear disc brakes: 1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on the vehicle’s spec line. 2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock
Show 3 more lines
from converting to rear disc brakes under this rule. 3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes as stock from converting to rear disc brakes under this rule."
B-Spec Update Honda Fit MT (07-08) Runoffs Eligibility
fasterB-Spec Honda Fit MT (07-08) becomes Runoffs-eligible; previous three-weekend Super Tour requirement removed.
In B-Spec Spec Lines, Honda Fit MT (07-08), change Notes as follows: "Bilstein B14 kit 47172401 verified compatible. Allow rear sway bar Progress #62.1060. Allow Injen Intake SP1511 OEM exhaust manifold required. Primary catalyst may be removed. This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted. (Effective 11/1/2025) Allow Torque Solution Shifter Cable Bushing kit TS-SCB-506."
HP Add TB size to Ford Mustang (94-98) Spec Line
#39130 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP Ford Mustang (94-98) fuel injected throttle body inside diameter specified at 60.
In EP Spec Lines, Ford Mustang (94-98) add the following to the Fuel Injected Equipped Throttle Body Inside Diameter column: "60"
STU Turbo Inlet Restrictor Table
#38961 from John Weisberg · Rule change · TB 25-12 (2025-12 Fastrack)
slowerSTU 36mm restrictor allows 2830 lbs (up 10 lbs from 2820); 37mm allows 2980 lbs (down 5 lbs from 2985).
In GCR, Section 9.1.4.H.3, change chart as follows:
A specification table follows in the original; it is not shown here.
STU 275 Tire Rule
#38983 from Peter Federlin · Rule change · TB 25-12 (2025-12 Fastrack)
slowerSTU cars over 3150 lbs lose 275-tire option with 2% weight adder.
In GCR, Section 9.1.4.G.1., change as follows: "A maximum section width of 245 is permitted. Cars over 3150 lbs. may run a 275 tire with a 2% weight adder."
HP Request to Re-Classsify Datsun SPL-311 to HP from FP
#39116 from Robert Heatwole · Rule change · TB 25-12 (2025-12 Fastrack)
neutralDatsun SPL-311 newly classified to HP at 2050 lbs with 1595cc OHV iron engine and specified carburetors.
In HP Spec Lines, classify Nissan/Datsun SPL 311 as follows:
A specification table follows in the original; it is not shown here.
HP TR2 Notes E&O
#39180 from Anthony Parker · Rule change · TB 25-12 (2025-12 Fastrack)
unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.
In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes: "Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."
HP Balance of Power
#39187 from Jim Simaras · Rule change · TB 25-12 (2025-12 Fastrack)
slowerEP BMW Z3 2.5L restrictor reduced 52mm to 50mm, weight increased to 2550 lbs base; five other BMW models get smaller restrictors.
In EP Spec Lines, make the following changes to Restrictors: BMW Z3 2.5L: "52mm 50mm Flat Plate Intake Restrictor" BMW Z3 2.8L (97-00): "55mm 53mm Flat Plate Intake Restrictor" BMW 328i/is E36 (96-99): "58mm 55mm Flat Plate Intake Restrictor" BMW 328i/ci E46 (01-06): "58mm 55mm Flat Plate Intake Restrictor" BMW 325i/is (E46) (01-06): "56mm 53mm Flat Plate Intake Restrictor" BMW 325is M-Technic (1994): "56mm 53mm Flat Plate Intake Restrictor" BMW 325i/is E-36 (92-95): "56mm 53mm Flat Plate Intake Restrictor"
Show 4 more lines
In EP Spec Lines, BMW Z3 2.5L, change Weight as follows: "2500 2550 *2563 2614 **2625 2678"
HP Alternative BOP Request for 84-87 Honda CRX/Civic
#39223 from Bill Lamkin · Rule change · TB 25-12 (2025-12 Fastrack)
fasterHP Honda Civic and CRX models get wider 13-inch wheels: 6 to 7 inches.
In HP Spec Lines, change Wheels as follows: Honda Civic: "13 x 6 7" Honda Civic DX (92-95): "13 x 6 7" Honda Civic/Si (84-87): "13 x 6 7" Honda Civic 1.5 (88-91): "13 x 6 7" Honda CRX/Si (84-87): "13 x 6 7" Honda CRX 1.5(88-91): "13 x 67"
STU STU Honda Engine weight penalty
#39375 from Super Touring Committee · Rule change · TB 25-12 (2025-12 Fastrack)
neutralB-Spec Chevrolet Sonic and Ford Fiesta, Honda Fit notes reorganized from individual allowances to approved parts lists; wording cleanup.
In B-Spec Spec Lines, Chevrolet Sonic Sedan MT (12-19), change Notes as follows: "GM suspension kit #23123679 permitted. Bilstein B14 kit #47-171725 verifed compatible. Allow rear sway bar ZZ Performance #ZZ-SNCRSB. Allow Aluminum Radiator #ZZP-ZZ013. Allow Babyface Fabrication brake caliper piston SNC-SS. Approved parts: ZZ Performance rear sway bar ZZ-SNCRSB, ZZ Performance radiator ZZP-ZZ013, Babyface Fabrication brake caliper piston SNC-SS. Bilstein B14 kit 47-171725 verified compatible." In B-Spec Spec Lines, Chevrolet Sonic Sedan AT (12-19), change Notes as follows: "GM suspension kit #23123679 permitted. Bilstein B14 kit #47-171725 verifed compatible. Allow rear sway bar ZZ Performance #ZZ-SNCRSB. For automatic allow Setrab 1-series Part No. FP119M221. Allow Aluminum Radiator #ZZP-ZZ013. Allow Babyface
Show 185 more lines
Fabrication brake caliper piston SNC-SS. Approved parts: ZZ Performance rear sway bar ZZ-SNCRSB, ZZ Performance radiator ZZP- ZZ013, Babyface Fabrication brake caliper piston SNC-SS, Setrab transmission cooler 50-119-7612. Bilstein B14 kit 47-171725 verified compatible. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Chevrolet Sonic Hatchback MT (12-19), change Notes as follows: "GM suspension kit #23123679 permitted. Bilstein B14 kit #47-171725 verifed compatible. Allow rear sway bar ZZ Performance #ZZ-SNCRSB. Allow Aluminum Radiator #ZZP-ZZ013. Allow Babyface Fabrication brake caliper piston SNC-SS. Approved parts: ZZ Performance rear sway bar ZZ-SNCRSB, ZZ Performance radiator ZZP-ZZ013, Babyface Fabrication brake caliper piston SNC- SS. World Challenge suspension kit permitted but no longer available. Bilstein B14 kit 47-171725 verified compatible." In B-Spec Spec Lines, Chevrolet Sonic Hatchback AT (12-19), change Notes as follows: "GM suspension kit #23123679 permitted. Bilstein B14 kit #47-171725 verifed compatible. Allow rear sway bar ZZ Performance #ZZ-SNCRSB. For automatic allow Setrab 1-series Part No. FP119M221. Allow Aluminum Radiator #ZZP-ZZ013. Allow Babyface Fabrication brake caliper piston SNC-SS. Approved parts: ZZ Performance rear sway bar ZZ-SNCRSB, ZZ Performance radiator ZZP- ZZ013, Babyface Fabrication brake caliper piston SNC-SS, Setrab transmission cooler 50-119-7612. Bilstein B14 kit #47-171725 verified compatible. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Lines, Ford Fiesta Hatchback (11-19), change Notes as follows: "Suspension kit #M-FR3-FAEB allowed. Rear axle bushing #000-04-2203-RR allowed. Allow rear torque bar Corksport #Mz2-3- 070. Cold air intake K&N 69-3530TS is allowed. Powerflex PFR19-1511BX2 rear suspension bushing allowed. Eibach rear sway bar #35143.312 o r35143.320 is allowed. Mazda front hub D651-33-06 and rear hub D651-26-15XE allowed. Approved parts: Eibach rear sway bar 35143.312, Corksport rear torque bar MZ2-3-070, K&N intake 69-3530TS, Powerflex rear suspension bushing PFR19-1511BX2, Mazda front hub D651-33-06, Mazda rear hub D651-26-15XE." In B-Spec Spec Lines, Ford Fiesta Sedan (11-19), change Notes as follows: "Suspension kit #M-FR3-FAEB allowed. Rear axle bushing #000-04-2203-RR allowed. Allow rear torque bar Corksport #Mz2-3- 070. Cold air intake K&N 69-3530TS is allowed. Powerflex PFR19-1511BX2 rear suspension bushing allowed. Eibach rear sway bar #35143.312 o r35143.320 is allowed. Mazda front hub D651-33-06 and rear hub D651-26-15XE allowed. Approved parts: Eibach rear sway bar 35143.312, Corksport rear torque bar MZ2-3-070, K&N intake 69-3530TS, Powerflex rear suspension bushing PFR19-1511BX2, Mazda front hub D651-33-06, Mazda rear hub D651-26-15XE." In B-Spec Spec Lines, Honda Fit MT (07-08), change Notes as follows: "Bilstein B14 kit 47172401 verified compatible. Allow rear sway bar Progress #62.1060. Allow Injen Intake SP1511 OEM exhaust manifold required. Primary catalyst may be removed. Allow Torque Solution Shifter Cable Bushing kit TS-SCB-506. Approved parts: Progress rear sway bar 62.1060, Injen intake SP1511, Torque Solution shifter cable bushings TS-SCB-506. Bilstein B14 kit 47172401 verified compatible. OEM exhaust manifold required. Primary catalyst may be removed." In B-Spec Spec Lines, Honda Fit AT (07-08), change Notes as follows: "Bilstein B14 kit 47172401 verified compatible. Any aftermarket header allowed. Allow rear sway bar Progress # 62.1060. Any Cold Air Intake Package allowed (any manufacturer). Approved parts: Progress rear sway bar 62.1060, Injen intake SP1511, Setrab transmission cooler 50-119-7612, any aftermarket header. Bilstein B14 kit 47172401 verified compatible." In B-Spec Spec Lines, Honda Fit MT (09-14), change Notes as follows: "Allow damper and spring set 51600F23SA100, Damper FR LH 51605F23SA100, Damper FR RH 51606F23SA100, Damper RR 52610F23SA100, Spring adjust asy RR 52691F23SA010. Seat upper FR spring 51688F23SA200, 51402FC4YA00 front helper spring and 51403FC4YA00 front spacer permitted. Front Damper Mount P/N 51920-F23S-A30 is allowed. Allow rear sway bar Progress # 62.1061 Allow Injen Intake SP1512, K&N Intake 69-1017TTK, or HPS intake 827-102 with a 25lb adder. Allow Acuity Shifter Base Bushing Kit 1954 Two pedal shutdown may be disabled by cutting/de-pinning pin 42 (BKSW) at the main ECU connector in the engine bay. Approved parts: Progress rear sway bar #62.1061, Injen Intake SP1512, K&N Intake 69-1017TTK, or Weapon R Intake 301-166-301, Acuity shifter bushing kit 1954. World Challenge suspension kit permitted but no longer available. Two pedal shutdown may be disabled by cutting/de-pinning pin 42 (BKSW) at the main ECU connector in the engine bay." In B-Spec Spec Lines, Honda Fit AT (09-14), change Notes as follows: "Allow damper and spring set 51600F23SA100, Damper FR LH 51605F23SA100, Damper FR RH 51606F23SA100, Damper RR 52610F23SA100, Spring adjust asy RR 52691F23SA010. Seat upper FR spring 51688F23SA200, 51402FC4YA00 front helper spring and 51403FC4YA00 front spacer permitted. Front Damper Mount P/N 51920-F23S-A30 is allowed. Allow rear sway bar Progress # 62.1061. Allow Setrab 50-119-7612 transmission cooler in addition to OEM. Any aftermarket exhaust/header allowed. Any Cold Air Intake Package allowed (any manufacturer). Weapon R Intake 301-166-301. Approved parts: Progress rear sway bar 62.1061, Injen Intake SP1512, any aftermarket header, Setrab transmission cooler 50-119-7612. Two pedal shutdown may be disabled by cutting/de-pinning pin 42 (BKSW) at the main ECU connector in the engine bay." In B-Spec Spec Lines, Honda Fit MT (15-19), change Notes as follows: "Allow damper FR LH 51605F23SA81, Damper FR RH FR RH 51606F23SA81, Damper RR 52610F23SA80, Spring adjust assy RR 52691F23SA80, Camber Adjuster Comp, Damper 51920F23SA82. Allow rear sway bar Progress 62.1063. Approved parts: Progress rear sway bar 62.1063." In B-Spec Spec Lines, Honda Fit CVT (15-19), change Notes as follows: "Allow damper FR LH 51605F23SA81, Damper FR RH FR RH 51606F23SA81, Damper RR 52610F23SA80, Spring adjust assy RR 52691F23SA80, Camber Adjuster Comp, Damper 51920F23SA82. Allow rear sway bar Progress 62.1063. Allow Setrab 50-119- 7612 transmission cooler in addition to OEM. Approved parts: Progress rear sway bar 62.1063, Setrab transmission cooler 50- 119-7612. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Hyundai Accent Hatchback (12-17), change Notes as follows: "Allow AKSJ03-10-001 Damper Frt Assembly; AKSJ03-20-001 Damper-ASTRear; KSJ03-20-003 Rear Upper Spring Perch Delrin; AKSJ03-60-001 Sump Pan Extension. Allow rear torque bar Evilla Motorsports #KR-B1. Bilstein B8 shock 33- 187112 approved for use in rear suspension. Bilstein B14 kit #47167490 front shocks verified compatible. Allow BabyFace Fabrication sump extension #BF-HYU-PAN Vehicles equipped with rear drum brakes subtract 25 lb. Approved parts: Evilla Motorsports rear torque bar KR-B1, BabyFace Fabrication sump extension BF-HYU-PAN. Vehicles equipped with rear drum brakes subtract 25 lbs." In B-Spec Spec Lines, Hyundai Accent Sedan (12-17), change Notes as follows: "Allow AKSJ03-10-001 Damper Frt Assembly; AKSJ03-20-001 Damper-AST-Rear; KSJ03-20- 003 Rear Upper Spring Perch Delrin; AKSJ03-60-001 Sump Pan Extension. Allow rear torque bar Evilla Motorsports #KR-B1. Bilstein B8 shock 33-187112 approved for use in rear suspension. Approved parts: Evilla Motorsports rear torque bar KR-B1, BabyFace Fabrication sump extension BF-HYU- PAN. Vehicles equipped with rear drum brakes subtract 25 lbs." In B-Spec Spec Lines, Kia Rio Hatchback (12-15), change Notes as follows: "Allow AKSJ03-10-001 Damper Frt Assembly; AKSJ03-20-001 Damper-AST-Rear; KSJ03-20- 003 Rear Upper Spring Perch Delrin; AKSJ03-60-001 Sump Pan Extension. Allow rear torque bar Evilla Motorsports #KR-B1. Bilstein B14 kit #47167490 front shocks verified compatible. Allow BabyFace Fabrication sump extension #BF-HYU-PAN Bilstein B8 shock 33-187112 approved for use in rear suspension. Approved parts: Evilla Motorsports rear torque bar KR-B1, BabyFace Fabrication sump extension BF-HYU-PAN. World Challenge suspension kit permitted but no longer available." In B-Spec Spec Lines, Kia Rio Sedan (12-17), change Notes as follows: "Allow AKSJ03-10-001 Damper Frt Assembly; AKSJ03-20-001 Damper-AST-Rear; KSJ03-20- 003 Rear Upper Spring Perch Delrin; AKSJ03-60-001 Sump Pan Extension. Allow rear torque bar Evilla Motorsports #KR-B1. Bilstein B8 shock 33-187112 approved for use in rear suspension. Approved parts: Evilla Motorsports rear torque bar #KR-B1, BabyFace Fabrication sump extension BF-HYU- PAN." In B-Spec Spec Lines, Mazda2 (10-14), change Notes as follows: "Rear sway bar 0000-04-2203-RR or 0000-04-2312, Allow rear torque bar Corksport #Mz2- 3-070. Cold air intake Corksport Mz2- 6-117-31100 and air duct Mz2-6-120-10 are allowed. Exhaust Header (cat delete) HB.EM 60-404-S-SS, HP-MZD001, allowed with a 50lb adder or Mazda Motorsports PN 0000-06-2410 with no weight adder permitted. Powerflex PFR19- 1511BX2 rear suspension bushings allowed. Allow Mazda part number 0000-01-2501-CR Radiator. Allow Mazda undertray part number DO8C- 56-110A, DO8C-56-311, DO7A-56-321. Approved parts: Mazda Motorsports rear sway bar 0000-04-2203-RR, Eibach/Mazda Motorsports rear sway bar 35143.312/0000-04-2312, Corksport rear torque bar #MZ2- 3-070, Corksport intake MZ2-6-117- 31100, Corksport air duct MZ2-6-120-10, Powerflex PFR19-1511BX2 rear suspension bushings, Mazda Motorsports radiator 0000-01-2501-CR, Mazda Motorsports header 0000-06-2410, Mazda undertray/side shields DO8C-56-110A, DO8C-56-311, DO7A- 56-321." In B-Spec Spec Lines, Mini Cooper Hatchback (R50) MT (02-06), change Notes as follows: "Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Allow rear sway bar Progress #62.0210. Approved parts: Progress rear sway bar 62.0210, Mevotech leteral link CMK100003. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches." In B-Spec Spec Lines, Mini Cooper Hatchback (R50) CVT (02-06), change Notes as follows: "Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Allow rear sway bar Progress #62.0210.CVT equipped cars allow Setrab 50-119-7612 transmission cooler in addition to OEM. Approved parts: Progress rear sway bar 62.0210, Mevotech leteral link CMK100003, Setrab transmission cooler 50-119- 7612. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches." In B-Spec Spec Lines, Mini Cooper (R56) MT (07-10), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. OBX header part #10- 2101-2S permitted. Approved parts: Progress rear sway bar 62.0210, OBX header 10-2101-2S. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. In B-Spec Spec Lines, Mini Cooper (R56) AT (07-10), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125.Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. OBX header part #10-2101-2S permitted. Automatic equipped cars only allow Setrab 50-119-7612 transmission cooler in addition to OEM. Approved parts: Progress rear sway bar 62.0210, Setrab transmission cooler 50-119-7612. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Mini Cooper Clubman (R55) (07-10), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. OBX header part #10- 2101-2S permitted. Approved parts: Progress rear sway bar 62.0210, OBX header 10-2101-2S. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. In B-Spec Spec Lines, Mini Cooper (R56LCI) MT (11-13), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. Approved parts: Progress rear sway bar 62.0210. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches." In B-Spec Spec Lines, Mini Cooper (R56LCI) AT (11-13), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. OBX header part #10- 2101-2S permitted with 41mm FPR. Automatic equipped cars only allow Setrab 50- 119-7612 transmission cooler in addition to OEM. Approved parts: Progress rear sway bar 62.0210, Setrab transmission cooler 50-119-7612. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Mini Cooper Clubman (R55) (11-15), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. Approved parts: Progress rear sway bar 62.0210. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches." In B-Spec Spec Lines, Mini Cooper Coupe (R58) (12-15), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. Approved parts: Progress rear sway bar 62.0210. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches." In B-Spec Spec Lines, Nissan Versa Sedan (2012-2019), change Notes as follows: "Hardrace HR-Q0146 19mm rear sway bar permitted. Allow Injen intake SP1906. Approved parts: Hardrace rear sway bar HR- Q0146, Injen intake SP1906." In B-Spec Spec Lines, Nissan Versa Hatchback (2012-2019), change Notes as follows: "Hardrace HR-Q0146 19mm rear sway bar permitted. Allow Injen intake SP1906. Approved parts: Hardrace rear sway bar HR- Q0146, Injen intake SP1906." In B-Spec Spec Lines, Nissan Versa (2020-), change Notes as follows: "This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Toyota/Scion IA Sedan (16-20), change Notes as follows: "This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted. Allow ST Suspension Kit 1327502. Approved parts: ST suspension kit 1327502. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Toyota Yaris Hatchback (07-11), change Notes as follows: "Speed sensor may be disconnected. Cold air intake K&N 69-8612TFK is allowed. Rear Swaybar PTR11-52071 is allowed. Approved parts: TRD rear sway bar PTR11-52071, K&N intake 69-8612TFK. Speed sensor may be disconnected." In B-Spec Spec Lines, Toyota Yaris Hatchback (12-18), change Notes as follows: "Rear Swaybar PTR11-52071 is allowed. Cold air intake K&N 69-8612TFK is allowed. Speed sensor may be disconnected. Vehicles equipped with rear disc brakes add 25 lb. Approved parts: TRD rear sway bar PTR11-52071, K&N intake 69-8612TFK. Speed sensor may be disconnected. Vehicles equipped with rear disc brakes add 25 lbs." In B-Spec Spec Lines, Toyota Yaris Sedan (07-12), change Notes as follows: "Rear Swaybar PTR11-52071 is allowed. Cold air intake K&N 69-8612TFK is allowed. Speed sensor may be disconnected. Approved parts: TRD rear sway bar PTR11-52071, K&N intake 69-8612TFK. Speed sensor may be disconnected."
Applies to Mini Cooper on this page: Trenton Kramer, Thomas Lepper
Applies to Toyota Yaris on this page: Joseph Gersch
unclearB-Spec: Sonic restrictors removed, Fit MT +25 lbs to 2550, Fit CVT restrictor removed, Mini Coopers restrictors increased 2-4 mm, Versa sedans -25 lbs to 2425, Versa/IA restrictors removed.
In B-Spec Spec Lines, change as follows: Chevrolet Sonic Sedan AT (12-19): Restrictor (mm) & Type: "35 FPR" Chevrolet Sonic Hatchback AT (12-19): Restrictor (mm) & Type: "35 FPR" Honda Fit MT (09-14): Weight (lbs): "2525 2550" Honda Fit CVT (15-19):
Show 23 more lines
Restrictor (mm) & Type: "33 FPR" Mini Cooper Hatchback (R50) MT (02-06): Weight (lbs): "2545 2525" Mini Cooper (R56) MT (07-10): Restrictor (mm) & Type: "FPR 45 47 OE Catalyst" Mini Cooper (R56) AT (07-10): Restrictor (mm) & Type: "47 FPR (OE Catalyst) 42 FPR (Header)" Mini Cooper Clubman (R55) (07-10): Restrictor (mm) & Type: "FPR 45 47 OE Catalyst" Mini Cooper (R56LCI) MT (11-13): Restrictor (mm) & Type: "FPR 44 46" Mini Cooper (R56LCI) AT (11-13): Restrictor (mm) & Type: "46 FPR (OE Catalyst) 41 FPR (Header)" Mini Cooper Clubman (R55) (11-15): Restrictor (mm) & Type: "FPR 44 46" Nissan Versa Sedan (2012-2019): Min weight: "2450 2425" Nissan Versa Hatchback (2012-2019): Min weight: "2450 2425" Nissan Versa (2020-): Restrictor (mm) & Type: "38 FPR" Toyota/Scion IA Sedan (16-20): Restrictor (mm) & Type: "38 FPR"
HP E/O: Improve Consistency of the Spec Lines
#39500 from Robert Bax · Rule change · TB 26-01 (2026-01 Fastrack)
unclearHP Toyota MR-2 1.6L (85-89) compression ratio set to 11.0:1.
In HP Spec Line, Toyota MR-2 1.6L (85-89), change Comp. Ratio as follows: "11.0:1"
STU Request for Permission on Aftermarket Turbo Kit and Intake
#39529 from John Grim · Rule change · TB 26-01 (2026-01 Fastrack)
fasterSTU Mazda MZR (LF, L3, L5) Turbo classified; Jack Spania Racing 70 mm intake manifold and Fab9 Tuning bottom-mount turbo kit approved.
In STU Spec Lines, Table A: Alternate Vehicle and Engine Allowances, Mazda MZR (LF, L3, L5), change Notes as follows: "Short blocks, heads, and intakes may be freely swapped within these engine designations. May use Goodwin Part # 61- 2510 or, Gato Performance Part #31972 or Jack Spania Racing 70 mm sheet-metal aluminum Intake manifold. Must use stock throttle body or Acura part number 16400-PND-A17." In STU Spec Lines, Table A: Alternate Vehicle and Engine Allowances, classify Mazda MZR (LF, L3, L5) Turbo as follows: STU Maximum Displacement (cc's) Minimum Weight Notes Mazda MZR (LF, L3, L5) Turbo
Show 7 more lines
Varies Chart Short blocks, heads, and intakes may be freely swapped within these engine designations. May use Jack Spania Racing 70 mm sheet-metal aluminum Intake manifold. Must use stock throttle body or Acura part number 16400-PND- A17. Fab9 Tuning bottom-mount turbo kit approved with one of the STU approved Turbos.
HP Request to Reclassify BMW 2002 Into H Production
#39567 from Jonathan Kinberg · Rule change · TB 26-01 (2026-01 Fastrack)
neutralBMW 2002 newly classified to H Production at 2350 lbs with 1990cc iron block, 40 DCNF carburetor, 11.0:1 compression.
In HP Spec Lines, classify BMW 2002, as follows:
A specification table follows in the original; it is not shown here.
In B-Spec Spec Lines, Mazda2 (10-14), change Notes as follows: "Exhaust Header (cat delete) HB.EM 60-404-S-SS, HP-MZD001, allowed with a 50lb adder or Mazda Motorsports PN 0000-06- 2410 with no weight adder permitted.”
HP Triumph Spitfire 1296cc Compression Ratio Increase to 12:1
#39589 from Neil Verity · Rule change · TB 26-02 (2026-02 Fastrack)
fasterHP Triumph Spitfire 1296cc compression ratio increases from 11.0 to 12.0:1.
In HP Spec Lines, make the following spec line changes: Triumph Spitfire: Carburetion "Valves: (I) 33.0/(1.30) (E) 29.7/(1.17) Comp. ratio 11.0 12.0:1, Valve lift .450” Trans. Speeds: 4" Triumph Spitfire Mk. III & IV 1500: Carburetion
neutralC-Spec rear sway bars approved for Chevrolet Cruze, Dodge Dart, Ford Focus, Honda Civic, Mazda3i, Toyota Corolla with specified part numbers.
In C-Spec Spec Lines, change Notes as follows: Chevrolet Cruze (2010-16): "Allow BC Racing Q-06-BR suspension kit or RedShift Q-06-CSPEC. Allow Babyface Fabrication brake caliper piston SNC- SS. Approved parts: BC Racing Q-06-BR or RedShift Q-06-CSPEC suspension kit, Babyface Fabrication brake caliper piston SNC- SS, ZZ Performance ZZ-SNCRSB or Whiteline BHR93 rear sway bar. Dodge Dart (2014-16): "Allow BC Racing or RedShift Z-06-CSPEC kit. Approved parts: BC Racing Z-06-BR or RedShift Z-06-CSPEC kit, Progress rear sway bar 62.0606."
Show 28 more lines
Ford Focus Hatchback/Sedan (2011-18): "Allow BC Racing E-21-BR or RedShift E-21-CSPEC kit. Allow Corksport Axl-3-318-Black adjustable rear camber arms. Approved parts: BC Racing E-21-BR or RedShift E-21-CSPEC suspension kit, Corksport Axl-3-318-Black adjustable rear camber arms, Corksport Axl-3-071-12, Eibach 35134.312, or Whiteline BMR78XZ rear sway bar." Honda Civic Coupe/Sedan (2012-15): "Allow BC Racing A-58-BR or RedShift A-18-CSPEC kit. Approved parts: BC Racing A-58-BR or RedShift A-18-CSPEC suspension kit, Progress 62.1026 or Megan Racing MRS-HA-0791 rear sway bar." Honda Civic Coupe/Sedan (2006-11): "Allow BC Racing A-18-BR or RedShift A-58-CSPEC kit. Approved parts: BC Racing A-58-BR or RedShift A-18-CSPEC suspension kit, Progress 62.1026 or Megan Racing MRS-HA-0791 rear sway bar." Mazda3i SKYACTIV (2012-13): "Allow BC Racing N-03-BR or RedShift N-03-CSPEC kit. Allow Corksport Axl-3-318-Black adjustable rear camber arms. Approved parts: BC Racing N-03-BR or RedShift N-03-CSPEC suspension kit, Corksport Axl-3-318-Black adjustable rear camber arms, Corksport Axl-3-071-12, Eibach 35134.312, or Whiteline BMR78XZ rear sway bar." Mazda 3i MZR (2010-13): "Allow BC Racing N-03-BR or RedShift N-03-CSPEC kit. Allow Corksport Axl-3-318-Black adjustable rear camber arms. Approved parts: BC Racing N-03-BR or RedShift N-03-CSPEC suspension kit, Corksport Axl-3-318-Black adjustable rear camber arms, Corksport Axl-3-071-12, Eibach 35134.312, or Whiteline BMR78XZ rear sway bar." Mazda 3i (2004-09): "Allow Corksport Axl-3-318-Black adjustable rear camber arms. Approved parts: BC Racing N-03-BR or RedShift N-03-CSPEC suspension kit, Corksport Axl-3-318-Black adjustable rear camber arms, Corksport Axl-3-071-12, Eibach 35134.312, or Whiteline BMR78XZ rear sway bar." Toyota Corolla (2007-12): "Allow BC Racing C-02-BR or RedShift C-02-CSPEC kit. Approved parts: BC Racing C-02-BR or RedShift C-02-CSPEC suspension kit, TRD PTR11-12080 or Megan Racing MRS-TY-1710 rear sway bar." Toyota Corolla (2013-18): "Allow BC Racing C-02-BR or RedShift C-02-CSPEC kit. Approved parts: BC Racing C-02-BR or RedShift C-02-CSPEC suspension kit, TRD PTR11-12080 or Megan Racing MRS-TY-1710 rear sway bar."
What the rules allowed changed as listed; this does not say what any particular car ran.