This track has been raced on 4 configurations (The Circuit, 2.57 mi; 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One session is left out because the timing does not look like full laps: Cal Club 2023 Qualifying #2.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Van Diemen RF01
FC
2
1:45.137Robert Armington
1:45.137Robert Armington
1:45.314Robert Armington
143.5Robert Armington
29.050Paul MacFarlane
30.109Robert Armington
45.728Robert Armington
Van Diemen DP-08
FC
1
1:45.137Robert Armington
1:45.137Robert Armington
1:45.314Robert Armington
143.5Robert Armington
29.106Robert Armington
30.109Robert Armington
45.728Robert Armington
Van Diemen RF01
FC
1
1:48.522Paul MacFarlane
1:50.067Paul MacFarlane
1:48.522Paul MacFarlane
114.4Paul MacFarlane
29.050Paul MacFarlane
31.137Paul MacFarlane
48.294Paul MacFarlane
Van Diemen RF96
FC
1
1:47.570Shawn Sarbacker
1:47.741Shawn Sarbacker
1:47.570Shawn Sarbacker
146.2Shawn Sarbacker
29.351Shawn Sarbacker
30.778Shawn Sarbacker
47.076Shawn Sarbacker
Van Diemen RF97
FC
1
1:47.993Bill Wallschlaeger
1:51.040Bill Wallschlaeger
1:47.993Bill Wallschlaeger
147.5Bill Wallschlaeger
29.638Bill Wallschlaeger
30.895Bill Wallschlaeger
47.233Bill Wallschlaeger
Swift Db6
FF
2
1:49.259Edward Erlandson
1:55.247Johnnie Crean
1:54.993Johnnie Crean
124.5Johnnie Crean
31.358Johnnie Crean
32.841Johnnie Crean
47.766Edward Erlandson
SWIFT DB-6 Honda
FF
1
1:49.259Edward Erlandson
47.766Edward Erlandson
Swift Db6
FF
1
1:54.993Johnnie Crean
1:55.247Johnnie Crean
1:54.993Johnnie Crean
124.5Johnnie Crean
31.358Johnnie Crean
32.841Johnnie Crean
50.291Johnnie Crean
Piper DL7-Honda
FF/STL
2
1:51.118Eric Poulsen
1:52.044Eric Poulsen
1:51.118Eric Poulsen
114.7Eric Poulsen
30.276Eric Poulsen
31.650Eric Poulsen
48.818Eric Poulsen
Piper DL7-Honda
FF
1
1:51.118Eric Poulsen
1:52.044Eric Poulsen
1:51.118Eric Poulsen
114.7Eric Poulsen
30.276Eric Poulsen
31.650Eric Poulsen
48.818Eric Poulsen
Honda Prelude
STL
1
1:56.961Carl Young
1:57.917Carl Young
1:56.961Carl Young
104.5Carl Young
31.994Carl Young
33.745Carl Young
50.892Carl Young
Mazda Miata
FP/STL
18
1:51.665Jared Korth
1:54.963Nick Leverone
1:54.845Gavin Wardle
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda MX-5
STL
6
1:51.665Jared Korth
1:57.404Ryan Gutile
1:54.845Gavin Wardle
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda Miata
STL
10
1:52.983Wesley Mollno
1:54.963Nick Leverone
1:55.682Nick Leverone
133.4Wesley Mollno
30.815Jon Davies
32.820Jon Davies
49.197Wesley Mollno
Mazda MIata
FP
1
1:56.276Steven Powers
1:57.032Steven Powers
1:56.276Steven Powers
134.3Steven Powers
31.570Steven Powers
33.696Steven Powers
50.716Steven Powers
Mazda MX-5 (2015)
STL
1
2:00.239Adrian Comstock
2:00.239Adrian Comstock
2:00.722Adrian Comstock
133.0Adrian Comstock
32.847Adrian Comstock
34.493Adrian Comstock
52.675Adrian Comstock
SWIFT DB-
FF
1
1:53.098Edward Erlandson
1:53.098Edward Erlandson
1:54.741Edward Erlandson
133.7Edward Erlandson
30.951Edward Erlandson
32.299Edward Erlandson
49.791Edward Erlandson
Mazda RX-8
STL
1
1:53.515David LeCren
2:09.464David LeCren
2:11.372David LeCren
121.0David LeCren
31.217David LeCren
32.486David LeCren
49.550David LeCren
Mazda RX-7
FP
1
1:55.440Michael Lewis
1:56.121Michael Lewis
1:55.440Michael Lewis
128.8Michael Lewis
31.255Michael Lewis
33.299Michael Lewis
50.847Michael Lewis
Nissan Sentra SE-R
FP
1
1:55.722Brian Linn
1:57.239Brian Linn
1:55.722Brian Linn
128.3Brian Linn
31.416Brian Linn
33.400Brian Linn
50.478Brian Linn
Volkswagen GTI
FP
1
1:56.016Tim Linerud
2:06.156Tim Linerud
93.4Tim Linerud
33.738Tim Linerud
35.656Tim Linerud
55.246Tim Linerud
Honda Civic Si
STL
1
1:56.438Jonathan Lugod
1:57.331Jonathan Lugod
1:56.438Jonathan Lugod
106.8Jonathan Lugod
31.787Jonathan Lugod
33.468Jonathan Lugod
50.873Jonathan Lugod
Van Diemen RF
FC
1
1:58.213Greg Pizzo
2:10.106Greg Pizzo
1:58.213Greg Pizzo
127.3Greg Pizzo
32.045Greg Pizzo
34.162Greg Pizzo
51.126Greg Pizzo
Fiat X 1/9
FP
1
1:59.128Daniel Snow
2:00.398Daniel Snow
1:59.128Daniel Snow
137.8Daniel Snow
31.878Daniel Snow
34.053Daniel Snow
52.221Daniel Snow
Porsche 914-4
FP
1
2:15.932Garey Raymond
2:21.274Garey Raymond
2:15.932Garey Raymond
84.8Garey Raymond
37.237Garey Raymond
39.091Garey Raymond
59.604Garey Raymond
Acura integra
STL
1
2:24.310Jack McEachern
2:24.310Jack McEachern
2:24.550Jack McEachern
77.6Jack McEachern
38.960Jack McEachern
41.141Jack McEachern
1:02.410Jack McEachern
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
FF Add Fast Forward Part Numbers for Honda Fit Engine
#33752 from Formula/Sports Racing Committee · Rule change · TB 23-03 (2023-03 Fastrack)
neutralFF Honda Fit engine adds Fast Forward part number alternatives for intake, exhaust, oil system, and scavenge pump components.
In FC/FF, GCR section 9.1.1.B.14.a.6, change as follows: "For all Honda part numbers in these specifications, superc seding part numbers are considered equivalent. In FC/FF, GCR section 9.1.1.B.14.f.5, change as follows: "Cylinder head breather restrictor must be used as supplied by HPD or Fast Forward, unmodified.: HPD PN: 15262-F21S-A200; Fast Forward PN: FF200-503." In FC/FF, GCR section 9.1.1.B.14.k.2, change as follows: "The upper manifold, air box and throttle body assembly must be used as delivered from Honda, HPD, or Fast Forward as noted below."
Show 35 more lines
In FC/FF, GCR section 9.1.1.B.14.k.2, insert as follows: "a. Intake manifold: HPD PN: 17210-F21S-A210; Fast Forward PN: FF200-201. b. Throttle body: Honda Fit: PN: 16400ZZ5024; HPD PN: 16400ZZ5024; Fast Forward PN: FF200-104. c. Throttle lever: HPD PN: 17330-F21S-A210; Fast Forward PN: FF200-101." In FC/FF, GCR section 9.1.1.B.14.k.3, change as follows: "All gaskets and sensors utilized on the inlet manifold from head to throttle body must be Honda Fit OEM, or HPD supplied or Fast Forward as noted below. a. Gasket In. manifold: HPD PN: 17105-RB0-004, Honda Fit OEM. b. Gasket, EGR chamber cover: HPD PN: 17146-RB0-004, Honda Fit OEM. c. Gasket In. port: HPD PN: 17115-RB0-007, Honda Fit OEM. d. Gasket, restrictor: HPD PN: 17399-F21S-A200, (2 required) HPD; Fast Forward PN: FF200-109. Two required." In FC/FF, GCR section 9.1.1.B.14.k.5, change as follows: "The Honda Fit engine is required to have an HPD supplied air inlet restrictor supplied by HPD or Fast Forward: HPD PN: 17344- F21S-A201; Fast Forward PN: FF200-110, with internal diameter of 30.5mm and thickness of 3.175mm (0.125 inches) correctly installed within the intake system." In FC/FF, GCR section 9.1.1.B.14.m.1, change as follows: "The exhaust manifold must be as supplied by HPD or Fast Forward:, HPD part # PN: 18150-F21S-A200 or # PN: 1818 50-F21S-B200; Fast Forward PN: FF500-001 or PN: FF500-002." In FC/FF, GCR section 9.1.1.B.14.n.1, change as follows: "The oil pan, baffle plate, and scavenge pump filter fittings must be as supplied by HP or Fast Forward as noted below. No modifications are permitted. a. Oil pan: HPD PN: 11200-F21S-A210 or PN: 11200-F21S-C240; Fast Forward PN: FF100-201A or PN: FF100-201B. b. Oil pan baffle plate: HPD PN: 11221-F21S-A210; Fast Forward PN: FF100-202. c. Oil scavenge pump filter fittings (2 required): HPD PN: 15180-F21S-A210; Fast Forward PN: FF100-204." In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows: "The scavenge pump and internal scavenge pump parts must be as supplied from HPD or Fast Forward as noted below." In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows: "b. Rotor outside diameter: HPD 44.400mm (1.748 inches):; Fast Forward 40.640mm (1.600 inches). c. Scavenge pump rotor set: HPD PN: 15450-F21S-A20; Fast Forward PN: FF100-110. d. Oil pump: HPD PN: 15100-F21S-A200; Fast Forward PN: FF100-100A. e. Scavenge pump cartridge: 15111-F21S-A21; Fast Forward PN: FF100-127. f. Scavenge pump port A: HPD PN: 15137-F21S-A20; Fast Forward PN: FF100-101. g. Scavenge pump port B: HPD PN: 15139-F21S-A20; Fast Forward PN: FF100-102. h. Scavenge pump shaft: HPD PN: 15510-F21S-A20; Fast Forward PN: FF100-103. i. Scavenge pump front cover: HPD PN: 15070-F21S-A21; Fast Forward PN: FF100-104."
FP Classification Request for 1978 Toyota Celica
#34097 from Bob Pharr · Rule change · TB 23-05 (2023-05 Fastrack)
neutralSTL ITA/ITS RX7 and 1985+ ITA/ITS/ITB/ITC vehicles clarified to conform to section 9.1.4.2 tire specifications.
In STL Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Notes as follows: ITA-spec and ITS-spec RX7: "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires must also conform to 9.1.4.2.Tires." ITS, ITA, ITB, or ITC vehicles (1985- ): "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires must also conform to 9.1.4.2.Tires."
neutralFord Fiesta HP and Chevrolet Sonic FP model year ranges extended from 2016 to 2019.
In HP, adjust model years of the "Ford Fiesta (11-16)" spec line as follows: "Ford Fiesta (11-16 9)" In FP, adjust model years of the "Chevrolet Sonic (12-16)" spec line as follows: "Chevrolet Sonic (12-16 9)"
FC USF2000 Van Diemen with Mazda MZR LF-DE 2.0L in FC
#34329 from Formula/Sports Racing Committee · Rule change · TB 23-06 (2023-06 Fastrack)
neutralUSF2000 Van Diemen with Mazda MZR LF-DE 2.0L added as spec line car in FC; removed from FX.
RM 23-07, USF2000 Van Diemen with Mazda MZR LF-DE 2.0L in FC, GCR section 9.1.1.B.1, add a new section and re-letter the following sections accordingly: "c. The USF2000 tube frame Van Diemen car powered by the Mazda MZR LF-DE 2 liter engine is added as a "spec line" car in Formula Continental. Additional "spec line" cars are disfavored, and Balance of Performance (BoP) adjustments to keep "spec line" cars competitive with cars that meet the class formula are likewise disfavored." In FC, GCR section 9.1.1.B.11, add the following: "The only permitted engines are: a. The Ford 2 liter single overhead camshaft "NE" series engine or the 1971-74 Pinto/Capri 2 liter single overhead camshaft
Show 9 more lines
engine. The specifications are contained in B.15. b. The Ford Zetec ZX3 2 liter dual overhead camshaft engine. The specifications are contained in B.16. c. The Mazda MZR LF-DE 2 liter for use only in USF2000 cars, as described in the Spec Line Cars Table below." In FC, GCR section 9.1.1.B, add the following: In FX, GCR section 9.1.1.J.B, change as follows and renumber the remaining lines accordingly: "3. USF2000 (tube frame) – Shall comply with FRP F2000 Technical Specifications (2018) 4. Pro Formula F2000 (tube frame) – Engine must be prepared to current FC rules." In FX Table 1, remove the USF2000 Tube Frame and Pro Formula F2000 Tube Frame spec lines in their entirety. Spec Line Cars Table
A specification table follows in the original; it is not shown here.
neutralFC tire marking rule clarified: four dry and wet tires for Regionals, eight each for Runoffs; damaged tire replacement procedures revised.
In FC, GCR section 9.1.1.B.10.h, change as follows: "FC shall be is permitted a maximum of four (4) dry tires and four (4) wet tires for all Regional, Major, and Super Tour events; eight (8) dry tires and eight (8) wet tires are permitted for the Runoffs. This rule shall be is effective beginning with the first (1st) qualifying session of the event. Marked tires are not required for testing or practice. It is the competitor's responsibility to ensure that the tires are declared, marked, and logged by Tech in advance of the tire(s) being used in a qualifying session or race. Failure to participate on marked tires will result in a penalty. 1. Use of an undeclared tire shall automatically result in all times being disallowed in that session or finishing position in that race.
Show 5 more lines
2. If a tire is damaged during a qualifying session or a race, the competitor may replace the damaged tire with a used tire upon approval by the Chief Steward without loss of time or finishing position. Second or subsequent damaged tires may similarly be replaced upon approval by the Chief Steward, however but such shall will result in the loss of grid position in the subsequent race or session; the competitor shall will start at the back of the grid. Replacement of a damaged tire with a new tire upon approval by the Chief Steward will result in loss of grid position in the subsequent race or session."
FP ITC to FP?
#34286 from David Snow · Rule change · TB 23-06 (2023-07 Fastrack)
neutralHP Volkswagen Rabbit Cabriolet 1780 removed; Rabbit 1588 and 1715 reclassified with engine sizes and year ranges specified.
In HP Spec Lines, Volkswagen Rabbit Cabriolet 1780, delete in its entirely: In HP, Spec Lines, Volkswagen Rabbit, change Title as follows: “Volkswagen Rabbit 1588 (includes Cabriolet / convertible)” “Volkswagen Rabbit 1715 (81-84) (excl. conv.)” “Volkswagen Rabbit GTI 1780 (83-84)”
FP Correct Intake Valve Size on 1500cc Midget/Spitfire
#34419 from Production Committee · Rule change · TB 23-06 (2023-05 Fastrack)
neutralFP and HP Sprite, Midget, and Spitfire 1500 intake valve size corrected to 36.6/(1.44).
In FP Spec Lines, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change Intake Valve Size as follows: "(I) 36.65.3/(1.44)" In FP Spec Lines, Triumph Spitfire Mk. IV & 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire Mk. III & IV 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)"
FP Porsche 944/924S Rule Change Request
#35002 from Adam Achepohl · Rule change · TB 23-12 (2023-12 Fastrack)
neutralEP Porsche 944/924S combines 2.5L and 2.7L variants with new weights: 2250–2415 lbs depending on engine and year.
In EP Spec Lines, delete the Porsche 944/924S 2.5L (2V) (83-88) spec line entirely, and create a new spec line for Porsche 944/924S 2.5L(2V) 2.7L(2V) (83-89) as follows:
A specification table follows in the original; it is not shown here.
FP FP and HP Toyota Corolla
#35030 from Keith Church · Rule change · TB 23-12 (2023-12 Fastrack)
fasterFP Toyota Corolla 2TC loses 43 lbs to 1810; HP Corolla loses 50–52 lbs to 1910–2006.
In FP Spec Lines, Toyota Corolla 2TC (71-74), change weight as follows: "1853 1810" In HP Spec Lines, Toyota Corolla (71-74), change weight as follows: “1960 1910 * 2009 1958 ** 2058 2006”
FP Triumph GT6 Adjustments
#35054 from ANTHONY PARKER · Rule change · TB 23-12 (2023-12 Fastrack)
fasterEP Triumph GT6 minimum weight reduced to 1800 lbs.
In EP Spec Lines, Triumph GT6, change weight as follows: "1830 1800"
FC Please correct omitted punctuation
#34890 from Club Racing Board · Rule change · TB 23-10 (2023-09 Fastrack)
neutralF600 Rotax 494, 493, 593 engines now require single expansion chamber and pull starter; electric starter optional.
In Cars and Equipment, GCR section 9.3.33.B.2, add the following: "(Effective 1/1/2024) A red taillight meeting FIA Standard 8874-2019, Technical List No. 76, is required on all Formula (open wheel) and Sports Racing cars." In Appendix F. Technical Glossary, Minimum Weight, change as follows: "Minimum Weight: – Weight specified with driver, exactly as they come off the race circuit, at the conclusion of any race or qualifying session." In FA Table 1, Spec Line E notes, add the following: "Any BD series iron or alloy cylinder block and alternate crankshaft permitted."
Show 8 more lines
In FC, GCR section 9.1.1.B.11.c, change as follows: "The Mazda MZR LF-DE 2 liter for use only in USF2000 cars, as described in the Spec Line Cars Table below."" In F600, GCR section 9.1.1.D.14, add the following: "Rotax Model 494, Model 493, and Model 593 must use a single expansion chamber and must be equipped with a pull starter; an electric starter may be added." In P1, GCR section 9.1.8.B.J.2, add the following: "Where a flat plate intake restrictor, restricted venturi, or Single Inlet Restrictor (SIR) is required, all intake air for each cylinder or the entire fuel-air mixture, if prepared before this point, must pass through the restrictor."
FP FP data
#35060 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)
slowerFP Acura Integra LS and Honda Del Sol VTEC minimum weights increase 25–78 lbs across all configurations.
In FP Spec Line, Acura Integra LS (94-01), change weight as follows: "2235 2260 *2291 2317 **2347 2373" In FP Spec Line, Honda Del Sol VTEC (94-97), change weight as follows: "2190 2265 *2245 2322 **2300 2378"
FP Request to Review Z3 2.5 Spec Line
#35073 from Tim Schreyer · Rule change · TB 24-01 (2024-01 Fastrack)
slowerEP BMW Z3 2.5L weight increases to 2500 lbs, 2563 lbs with turbo, 2625 lbs with supercharger.
In EP spec line, BMW Z3 2.5L, change weight as follows: "2450 2500 *2511 2563 **2573 2625"
STL Alternate Carburetor Request for 79-85 RX7 12a
#35181 from Dan Sheppard · Rule change · TB 24-01 (2024-01 Fastrack)
unclearSTL Mazda RX-7 12A (79-85) now allows auto-type 2 bbl with 42mm choke(s) on dual-y manifold as alternate to stock Nikki 4 bbl.
In STL Table B: Alternate Vehicle and Engine Allowances, Mazda RX-7 12A (79-85), change Notes as follows: "Street Porting of the engine only. Bridge porting, peripheral porting, and eyelash porting are prohibited. Contact SCCA National Office for details of Street porting. Stock Nikki 4 bbl carburetor on a stock manifold only. or auto-type 2 bbl w/42mm choke(s) on a “dual-y” manifold. Allow the standard removal of emissions related components, and allow air and fuel jets to be corrected. Modification of the water jacket in the area of the spark plug for cooling purposes is permitted."
FP Corrections to Honda Spec Lines in FP
#35250 from Jonathan Spiegel · Rule change · TB 24-01 (2024-01 Fastrack)
unclearFP Honda throttle body specs corrected: Civic 1.5 to 42", Si to 55", CRX variants adjusted.
In FP Spec Lines, change Fuel Injected Equipped Throttle Body Inside Diameter as follows: Acura Integra GSR (92-93): "58" Honda Civic 1.5 (88-91): "NA 42" Honda Civic EX (90-91): "55" Honda Civic Si (88-91): “42 55” Honda CRX 1.5 (88-91): “33 (primary) 42 (secondary) 42” Honda CRX / CRX Si (84-87): ”42 33 (primary) 42 (secondary)” Honda CRX Si (88-91): ”NA 55”
FP Miata Alternate Head
#35253 from Don Tucker · Rule change · TB 24-01 (2024-01 Fastrack)
fasterEP Mazda MX-5 1.8L 1990-97 minimum weight drops to 2150 lbs; 1994-97 variants to 2000, 2050, 2100 lbs respectively.
In EP Spec Lines, Mazda MX-5 /Miata 1.8L (90-97), change weight as follows: "2200 2150" Mazda MX-5 /Miata (94-97) "2035 2000 *2086 2050 **2137 2100"
FP Triumph GT6 Adjustments
#35255 from Anthony Parker · Rule change · TB 24-01 (2024-01 Fastrack)
In EP spec line, Triumph GT6, make the following change in the Notes section: "Two (2) 1.75” auto-type carburetors @ 1970 40 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive. Three (3) Weber 40mm DCOE w/28mm venturi on individual runner manifold @ 2020 lb."
FP Honda S2000 throttle body
#35272 from Aaron Johnson · Rule change · TB 24-01 (2024-01 Fastrack)
fasterEP Honda S2000 fuel injected throttle body inside diameter increases from 62mm to 64mm.
In EP spec line, Honda S2000, make the following changes to its spec line: Fuel Injected Equipped Throttle Body Inside Diameter: "62 64" Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .500”. An adaptor plate can be used to mount the 62mm throttle body from '00-05 to the '06-09 intake manifold. The adaptor plate can be no more than 1.25" thick, and its bore must not exceed the "Fuel Injected Equipped Throttle Body Inside Diameter" maximum spec of 64mm."
neutralFF Honda Fit gains Fast Forward FF800-100 oversize piston ring pack option.
In FF, GCR section 9.1.1.B.14.e.3.a, add the following: "The standard ring pack, PN 13011-RB1-004 (Riken) or 13011-RB1-006 (Nippon), or the oversize ring pack, PN 13021-RB7-Z01 (Riken), or 13021-RB7-Z02 (Nippon), or FF800-100 (Fast Forward), may be used."
FP Correction within Triumph TR8 Spec Line
#35315 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)
neutralEP Triumph TR8 dry sump allowance moved from carburetor line to notes section.
In EP spec line, Triumph TR8 (78-81), move the "Dry sump allowed" wording to the appropriate location as follows: Carburetor. No. & Type: “Zenith Stromberg carbs or fuel injection. Dry sump is allowed.” Notes: “Comp. Ratio limited to 12.0:1, Valve lift limited to .500”. Dry sump is allowed.”
FP Correction to EP 924S/944 Spec Line
#35317 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)
neutralEP Porsche 944/924S 2.5L and 2.7L weight minimums corrected: 2479cc to 2306/2363 lbs, 2681cc to 2358/2415 lbs.
In EP spec line, Porsche 944/924S 2.5L (2V) / 2.7L (2V) (83-89), change Weight as follows:
A specification table follows in the original; it is not shown here.
STL ST Electric-Assisted Steering Systems
#35066 from Jose Osiris Pena · Rule change · TB 24-02 (2024-01 Fastrack)
neutralSTL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems.
In GCR, Section 9.1.4.M.16., change as follows: "Power steering may be modified in any of the following ways: a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be modified internally to work without pump. b. an OEM manual steering rack for that model may be fitted c. an electric power steering pump may be fitted d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used e. an OEM hydraulic-assisted steering system may be used"
STL BOP Adjustments
#35112 from Super Touring Committee · Rule change · TB 24-02 (2024-01 Fastrack)
fasterSTL Acura/Honda B-series and Mazda MZR restrictors reduced 2mm; minimum weights down 25–75 lbs for 1900–2000cc engines.
In GCR, 9.1.4.H.1., change as follows: "Minimum weights for cars with normally aspirated piston engines will be determined by 1.35 lbs/cc displacement for the installed engine (see the following table). Displacement is the factory displacement for the installed engine. For the purpose of weight assignment, engine displacement will be rounded to the nearest 50cc (e.g., 2176cc = 2200cc and 2175cc = 2150cc)." In GCR, 9.1.4.H.1., change Minimum Weight on Chart as follows: Factory Engine Displacement 1900: "Effective 3-1-24: 2565 2540" Factory Engine Displacement 1950: "Effective 3-1-24: 2633 2583"
Show 11 more lines
Factory Engine Displacement 2000: "Effective 3-1-24: 2700 2625" In GCR, 9.1.4.H.3., change as follows: "Front wheel drive cars with a strut type front suspension may reduce their minimum weight by 2.5 percent. Effective 3- 1-24: Front wheel drive cars with 95" or less wheelbase must add 1.25% to their minimum weight." In STL Spec Lines, change Notes as follows: Acura/Honda B16: "Effective 3-1-24: 53 51mm" Acura/Honda B17: "Effective 3-1-24: 53 51mm" Acura/Honda B18C1: "Effective 3-1-24: 53 51mm" Acura/Honda B18C (JDM Type R), B18C5 (USDM Type R), B18C6 (UK and Euro Type R), B18C7 (Australia Type R): "Effective 3-1-24:52 50mm" Mazda MZR: "Effective 3-1-24: 52 50mm"
STL Mazda 12A
#35320 from Super Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)
slowerSTL Mazda 12A must keep 5th and 6th intake port actuators and valves, no longer allowed removal or disabling.
In STL Spec Lines, Table A, Mazda 12A, change Notes as follows: "The 5th and 6th intake port actuators and valves may be removed or disabled."
In HP Spec Lines, delete the following redundant spec lines in their entirety: Spec line #10 - VW Rabbit Cabriolet 1780 Spec line #3 - VW Scirocco 1588 Spec line #4 - VW Scirocco 1780 (8-valve) (83-88) Spec line #5 - VW Scirocco 1588
FP Update FP Protege (01-03) Model Info
#35715 from Production Committee · Rule change · TB 24-03 (2024-03 Fastrack)
neutralFP Mazda Protégé ES (01-03) model designation updated to include /5 variant.
In FP Spec Lines, Mazda Protégé ES (01-03) change vehicle as follows: "Mazda Protégé ES/5 (01-03)"
FC Four Pot Calipers
#35481 from Steve Jenks · Rule change · TB 24-04 (2024-04 Fastrack)
neutralFC adds F2000 Metrik ZF2 with Ford Zetec engine and four-piston Brembo calipers as spec-line car.
In FC Table FC Charts, add the following: In FC, GCR section 9.1.1.B.1.c, change as follows: "The USF2000 tube frame Van Diemen car powered by the Mazda MZR LF-DE 2 liter engine and the F2000 Metrik ZF2 car equipped with 4-piston calipers is are added as a "spec line" cars in Formula Continental. Additional "spec line" cars are disfavored, and Balance of Performance (BoP) adjustments to keep "spec line" cars competitive with cars that meet the class formula are likewise disfavored." FC Charts Car Engine Wheel Width
Show 1 more lines
(in) ± .060 Aero Transmission Weight Notes
A specification table follows in the original; it is not shown here.
neutralFP Honda CRX 84-87 can replace plastic front header, rocker skirt, door cap panels with stock-appearance replicas in alternate materials.
In FP spec line "Honda CRX / CRX Si (84-87)", add the following wording to the Notes section: "The plastic OE front header/nose body panel, lower rocker side-skirt, and lower door cap panel can be replaced by a replica, which may be constructed of an alternate material, provided its appearance remains stock."
FP FP data and parity
#35896 from Production Committee · Rule change · TB 24-05 (2024-05 Fastrack)
slowerFP Acura Integra and Honda Civic models now require 55mm Flat Plate Intake Restrictor.
In the following FP spec lines, add the following wording to the Notes section: Acura Integra (90-93) Acura Integra LS (94-01) Acura Integra GSR (92-93) Honda Civic Del Sol VTEC (94-97) Honda Civic Si (99-00) "55mm Flat Plate Intake Restrictor is required."
neutralNissan 300ZX 84-89 classified to EP at 2550 lbs minimum, 2960cc 6-cyl SOHC, fuel injection, 12.0:1 compression limit, 0.500" valve lift limit.
In EP Spec Lines, classify Nissan 300ZX (84-89), as follows:
A specification table follows in the original; it is not shown here.
FP RX7 1993 and Up Request In EP Spec Lines, classify
#36031 from Edward Zabinski · Rule change · TB 24-06 (2024-06 Fastrack)
neutralMazda RX-7 92-97 newly classified EP Prep Level 2 at 2200–2310 lbs with 13B 6-port rotary engine.
Mazda RX-7 (92-97) as follows:
A specification table follows in the original; it is not shown here.
FP Clean-up Multiple EP RX-8 Spec Lines In EP
#36156 from Production Committee · Rule change · TB 24-06 (2024-06 Fastrack)
neutralEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.
Spec Lines, make the following changes to the two Mazda RX-8 spec lines. Remove spec line entirely: Mazda RX-8 (04-11) Remove the wording "alternate": Mazda RX-8 (04-11)(alternate) Spec Mazda (SM/SMX) None.
neutralHP Volkswagen Golf and Jetta 85-92 track correction: front 1537mm (60.5in), rear 1529mm (60.2in).
In HP Spec Lines, change Track (F/R)mm/(in.) as follows: Volkswagen Golf (GTI, GT, GL) (85-92): "2 1537/1529 (60.5/60.2)" Volkswagen Jetta (GLI, GL) (85-92): "2 1537/1529 (60.5/60.2)"
FF Update to FF EGR Blanking Plate Rule
#36633 from Matt Boian · Rule change · TB 24-10 (2024-10 Fastrack)
neutralFF VTEC activation valve must function; EGR blanking plate rule clarified with Fast Forward part numbers.
In FF, GCR section 9.1.1.B.14.r.1, change as follows: "All emission control devices must be removed and blocked off by the blanking plate provided by HPD or Fast Forward as noted below, except for the VTEC activation valve. The VTEC activation valve must be retained; and it must be functioning. No modifications are permitted. a. EGR Plate: Fast Forward PN: FF200-301. b. EGR Port Cover: Fast Forward PN: FF200-302."
FP Errors/emissions Honda Civic/CRX
#36700 from Martin Burk · Rule change · TB 24-10 (2024-10 Fastrack)
fasterFP Honda CRX/CRX Si 84-87 block material changes from Iron to Alum.
In FP Spec Lines, Honda CRX / CRX Si (84-87), change Block Mat'l as follows: "Iron Alum"
fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1" In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
slowerFC tire limit reduced to four dry and four wet for Regional/Major/Super Tour, eight for Runoffs.
In FC, GCR section 9.1.1.B.10.h, change as follows: "(Effective 11/1/2024) FC is permitted a maximum of four (4) dry tires and four (4) wet tires for all Regional, Major, and Super Tour events; eight (8) dry tires and eight (8) wet tires are permitted for the Runoffs. This is effective beginning with the first (1st) qualifying session of the event. Marked tires are not required for The tire limit does not apply to testing or practice. It is the competitor's responsibility to ensure that the tires are declared, marked, and logged by Tech immediately upon conclusion of the first qualifying session, as provided in the event supplemental regulations, or per the instructions of the Race Director or Chief Steward. in advance of the tire(s) being used in a qualifying session or race. Failure to participate on marked Use of tires in excess of the number allowed will result in a penalty. Failure to participate on declared/marked/logged tires after the time
Show 6 more lines
prescribed for the same may result in a penalty. If a tire is damaged during a qualifying session or a race, the competitor may replace the damaged tire with a used tire upon approval by the Race Director or Chief Steward without loss of time or finishing position. Second or subsequent damaged tires may similarly be replaced upon approval by the Race Director or Chief Steward, but such will result in the loss of grid position in the subsequent race or session; the competitor will start at the back of the grid. Replacement of a damaged tire with a new tire upon approval by the Race Director or Chief Steward will result in loss of grid position in the subsequent race or session; the competitor will start at the back of the grid."
FC Change FF/FC Weight with Sequential Gearbox
#36651 from Robert Wright · Rule change · TB 24-11 (2024-11 Fastrack)
fasterFF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs.
In FF, GCR section 9.1.1.B.20.A.3, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight." In FC, GCR section 9.1.1.B.20.B.4, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
FF Change FF/FC Weight with Sequential Gearbox
#36651 from Robert Wright · Rule change · TB 24-11 (2024-11 Fastrack)
fasterFF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs.
In FF, GCR section 9.1.1.B.20.A.3, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight." In FC, GCR section 9.1.1.B.20.B.4, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
FF Alternative Oversize Honda Fit Pistons
#37064 from Formula/Sports Racing Committee · Rule change · TB 24-11 (2024-11 Fastrack)
neutralFF Honda Fit allows Fast Forward 0.25mm oversize pistons PN FF800-110 as alternative; piston diameter spec clarified to 2.8835 inches.
In FF, GCR section 9.1.1.B.14.e.1, change as follows: "Honda Fit OEM standard size pistons, PN: 13010-RB1-000, or Honda Fit OEM 0.25mm oversize pistons, PN: 13020-RB7-Z00, or Fast Forward 0.25mm oversize pistons, PN: FF800-110, may be used." In GCR section 9.1.1.B.14.e.2, change as follows: "a. Maximum standard piston diameter, measured at a point 16mm from the bottom of the skirt: 73.240mm (2.8834 2.8835 inches). b. Centerline of wrist pin to crown maximum: 26.21mm (1.032 inches). c. Maximum overall height from skirt to crown edge: 47.80mm (1.882 inches).
Show 13 more lines
d. Minimum weight: 198.0 grams (6.984 ounces). e. Minimum weight of piston pin: 66 grams (2.25 ounces). f. Combined minimum weight of piston, piston pin and connecting rod: 543.5 grams (18.85 ounces). g. Combined minimum weight of piston, wrist pin, and circlips: 267 grams (9.418 ounces). h. Centerline of wrist pin to crown edge: 26.289mm (1.035 inches). i. Ring groove widths: Top ring groove: 1.003mm (0.0395 inches). Middle ring groove: 1.016mm (0.0400 inches). Oil ring groove: 1.981mm (0.0780 inches). j. Ring groove distance from wrist pin center to bottom of groove: Top ring groove: 19.63mm (0.7730 inches). Middle ring groove: 15.29mm (0.6020 inches). Oil ring groove: 10.91mm (0.4295 inches)."
STL Request to Remove Miata Hubs from General category
#37138 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)
neutralSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
In GCR, Section 9.1.4.M.18., change as follows: "18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."
FP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line
#37119 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)
fasterEP BMW 325i/is E30 (84-91) weight reduced 50–52 lbs across three spec lines to 2150, 2204, 2258.
In EP SPEC LINES, BMW 325i/is (E30) (84-91), change Weight as follows: "2200 2150 *2255 2204 **2310 2258"
FP Fix Error in Spridget Spec Line
#37437 from Jason Stine · Rule change · TB 25-01 (2025-01 Fastrack)
neutralFP Spridget and Midget 1275cc and 1500cc spec line corrections to bore, stroke, displacement, and valve sizes.
In FP SPEC LINES, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change the following: 1275cc: Bore x Stroke: "68.1x78.4 (2.68x3.09) 70.6x81.3 (2.78x3.20)" Displacement: "(77.78) 1275" Valves IN & EX: "(I) 32.1/(1.26) (E) 28.4/(1.12) (I) 33.3/(1.31) (E) 29.5/(1.16)" 1500cc: Bore x Stroke: "1.1x84.3 73.7x87.4 (2.90x3.44)" Displacement: "1491 (90.95) 1493"
Show 1 more lines
Valves IN & EX: "(I) 36.6/(1.44) (E) 28.7 29.7/(1.17)"
FP Create ruleset that allows GTL cars to run in FP
#37485 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)
neutralF Production now allows GT-Lite cars meeting Appendix N specifications to compete, effective 2025-01-01.
“(Effective January 1, 2026) (Effective January 1, 2025)." Any GT-Lite (GTL) car meeting all of the requirements of Appendix N GT-LITE CATEGORY SPECIFICATIONS for inclusion into F PRODUCTION" may compete in the F-Production class. For GTL cars competing in FP, the level of preparation and modifications will be determined by Appendix N and not by PCS 9.1.5.”
neutralFP GTL Volkswagen Jetta Mark IV 4dr FWD 98.2 wheelbase newly classified.
In FP Spec Lines, Appendix N, GTL-FP Cars - Volkswagen, classify Jetta Mark - IV as follows: GTL-FP Cars - VOLKSWAGEN Model Years Body Style Drive-line Wheelbase (in) Notes Jetta Mark - IV 4dr FWD 98.2
FP GTL/FP consolidation 2025 Rules
#37659 from James Gregorius · Rule change · TB 25-03 (2025-03 Fastrack)
neutralFP Spec Lines option: carburettor chokes permitted as alternative to SIR, same size as listed SIR.
In FP Spec Lines, Appendix N: L.9, Fuel Injection System, add the following: "As an option, induction system “Chokes” may be used where a SIR is required. Said chokes shall be fitted to each barrel of carburetor/throttle body and all airflow into engine must pass through them. Choke size will be the same as listed SIR unless noted."
FF Formula F Proposal to Invite Older Cars Via a Tire Rule Change
#37802 from Anthony Stefanelli · Rule change · TB 25-03 (2025-03 Fastrack)
fasterFF allows older cars with rocker arm or outboard suspension to use bias ply slicks or VFF tires instead of radials.
In FF, GCR section 9.1.1.B.10.e, change as follows: "Formula F shall be limited to the following tires (front tires may not be used as rears): Dries: Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13 Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13 Wets: Front - Hoosier Wet or W3 Radial 44421 185/60R13 Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Show 12 more lines
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at least one chassis end may use the following tires: Dries: Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick Wets: Radial wets listed above or Front - Hoosier 44165 135/545-13 VFF Rear - Hoosier 44170 165/580-13 VFF Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."
FP Request for Classification of Chevrolet Spark
#37755 from Kristian Smith · Rule change · TB 25-04 (2025-04 Fastrack)
neutralChevrolet Spark 16-22 classified HP Pre at 1850 lbs minimum weight, fuel injected, 1399 cc.
In HP Spec Lines, classify the Chevrolet Spark (16-22):
A specification table follows in the original; it is not shown here.
FP Request to Lower Ford Festiva Minimum Weight to 1600 LBS
fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.
In HP Spec Lines "Ford Festiva (88-93)" change as follows: Weight: "1700 1600 *1743 1640 **1785 1680" Notes: "Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."
unclearSTL Mazda MX5 Challenge minimum weight now references GCR 9.1.7.1 instead of 2500 lbs; spec components removed, only alternative tires allowed.
In STL Spec Lines, Table B, Mazda Spec MX5 Challenge, change as follows: Minimum Weight: "2500 See 9.1.7.1." Notes: "Mazda MX5 Challenge car must utilize the following components: Roush CNC cylinder head 0000-01-5300,Mahle standard or +0.005 0000-01-5310, OEM camshaft, 11:1 compression ratio, header 0000-06-5407-NC, exhaust 0000-06-5427-NC, cold air intake 0000- 06-5150-KT, ECU flash 0000-01-5379, Pagid front brake pads 0000-03-5104-SP or endurance pads 0000-03- 5104-EN, Pagid rear brake pads 0000-03-5114-SP or endurance pads 0000-03-5114-EN, Penske front shock 0000-04-5291-SA, Penske rear shock 0000-04-5292-SA, Penske rear mount kit 0000-04-5358, Front mount kit 0000-04-5359, Front offset bushing 0000-04-5407-NC, Eibach front springs 0000-04-9700-08, Eibach rear springs 0000-04-9400-07, Eibach helper springs 0000-04-
Show 5 more lines
9926, Eibach front sway bar 0000-04-5306-FT, Eibach rear sway bar 0000-04-5306-RR, Interior finish panels 0000-07-5822, C&R radiator/oil cooler assembly 0000-01-5504-CR, Oil cooler adapter and lines 0000-01-5511-KT, ACT clutch 0000-02-5004-G6, wheels 17x8 #0000-04-5706-GM, # 0000- 04-5706-SL, and Toyo RR 235-40-17 dry, Toyo RA1 235-40-17 wet. Alternative tires on 17x7 wheels per STL rules. No other Super Touring modifications or allowances permitted except as noted in this spec line. Must conform completely to GCR 9.1.7.1, except alternative tires (only) per STL regs allowed."
Applies to Mazda Miata on this page: Jared Korth, Ricardo Arruda, Gavin Wardle, Ryan Gutile, Bryce Johnson, Andy Chittum, Adrian Comstock
FF Page 228, FF tire rule 9.1.1.10.e
#38251 from Anthony Stefanelli · Rule change · TB 25-05 (2025-05 Fastrack)
neutralFF adds rocker arm and outboard suspension cars optional bias ply and VFF tires; removes front-as-rear rule, adds mixing restrictions.
In FF, GCR section 9.1.1.B.10.e, change as follows: "Formula F shall be limited to the following tires (front tires may not be used as rears): Dries: Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13 Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13 Wets: Front - Hoosier Wet or W3 Radial 44421 185/60R13 Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Show 16 more lines
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at least one chassis end may use the following tires: Dries: Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick or Hoosier 44165 135/545-13 VFF Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick or Hoosier 44170 165/580-13 VFF Wets: Radial wets or VFF tires listed above or Front - Hoosier 44165 135/545-13 VFF Rear - Hoosier 44170 165/580-13 VFF Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."
FP Base Weight Adjustment for H-Production X1/9 Spec Lines
#38255 from Matthew Brannon · Rule change · TB 25-06 (2025-06 Fastrack)
fasterHP Fiat X-1/9 base weights reduced 50–53 lbs across 1300 and 1500 spec lines.
In HP Spec Lines, change Weight as follows: Fiat X-1/9 & Bertone1500: “1790 1740 *1835 1784 **1880 1827” Fiat X-1/9 1300: “1650 1600 *1691 1640 **1733 1680” Fiat X-1/9 1300: “2060 2010” Fiat X-1/9 1500: “1950 1900”
slowerEP BMW Z4 03-05 restricted to 52mm flat plate intake restrictor.
In EP Spec Lines, BMW Z4 (03-05), add to Notes the following: “52mm Flat Plate Intake Restrictor.”
FP EP Fiat 124 Spider Competition Adjustment Request
#38498 from John Baucom · Rule change · TB 25-07 (2025-07 Fastrack)
fasterEP Fiat 124 Spider 1600 & 2000 weight drops 50 lbs to 2000; carburetors gain 2mm chokes to 36mm.
In EP Spec Lines, Fiat 124 Sport Spider 1600 & 124 Spider 2000, change as follows: Weight: "2050 2000" Carburetor No. & Type: "(2) Weber 40 IDF-40IFI, (2) Solex C40P116, 34 36mm choke(s) req’d, (2) Weber 45DCOE w/ 34 36 mm choke(s) on I.R. manifold or fuel injection."
STL Lotus Weight Reduction
#38772 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)
fasterSTL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs.
In 9.1.2. GT2/ST Spec Lines, Lotus Evora GT4, change Weight as follows: "2750 2700" In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows: Lotus Elise Cup R: "2300 2250" Lotus Elise SC/ Lotus Exige SC: "2300 2550 2500 2450"
FP HP Plymouth Arrow spec omission
#38995 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralHP Plymouth Arrow transmission max speeds clarified to 4 or 5.
In HP Spec Lines, Plymouth Arrow (76-80), add the following wording to Trans. Speeds(max): "4 or 5"
FP Add Wheel Diameter to Appendix G
#39008 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP wheel diameter added to Appendix G as absolute maximum specification.
In Appendix G.2.3, change as follows: "Rim width and diameter are is absolute maximums."
FP Add TB ID tolerance to general Prod rules
#39009 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.
In GCR, Section 9.1.5.E., change as follows: 9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished." 9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must remain stock (tolerance of +/-.25mm)."
FP Please Lower Weight of 280Z
#38871 from Matthew Miller · Rule change · TB 25-09 (2025-09 Fastrack)
fasterEP Nissan 280Z minimum weight reduced from 2560 to 2400 lbs.
In EP Spec Lines, Nissan 280Z, change Weight (lbs) as follows: "(Effective 11/1/2025) 2560 2400 *2624 2460 **2688 2520"
FP Miata Weight Adjustment Follow Up
#38949 from Don Tucker · Rule change · TB 25-10 (2025-10 Fastrack)
fasterEP Mazda MX-5 1.8L 90-97 weight reduced to 2125 lbs from 2150 lbs.
In EP Spec Lines, Mazda MX-5 / Miata 1.8L (90-97), Effective 11/1/2025 make the following weight change: "2150 2125"
FP Weight Break for 1098 Midget / Sprite
#38970 from Kendall Jones · Rule change · TB 25-10 (2025-10 Fastrack)
In HP Spec Lines, Austin-Healey Sprite/Midget 1098cc, Effective 11/1/2025make the following weight change: "1630 1550"
FP HP Volvo 142 spec omission
#38994 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".
In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."
FP HP Mini DOHC 1.6
#38996 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following changes to the Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
FP 83-88 FP Scirocco Spec Line Creation
#38997 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralFP Scirocco 83-88 established as spec line with 1733–1803 lbs, 1715–1780 cc SOHC, 40/33 mm valves, Solex carbs or fuel injection.
In FP Spec Lines, classify Volkswagen Scirocco (83-88) as follows:
A specification table follows in the original; it is not shown here.
FP Add to Rabbit description
#39019 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.
In FP Spec Lines, make the following spec line correction: "Volkswagen Rabbit (Includes Convertible Cabriolet)" In HP Spec Lines, make the following spec line correction: "Volkswagen Rabbit 1588 (Includes Cabriolet)" "Volkswagen Rabbit 1715 (Includes Cabriolet)" "Volkswagen Rabbit 1780 (Includes Cabriolet)"
FP Clean-up 9.1.5.E.7e
#39025 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.
In GCR, Section 9.1.5.E.7., change as follows: "e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear disc brakes under this rule. When converting from rear drum brakes to rear disc brakes: 1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on the vehicle’s spec line. 2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock
Show 3 more lines
from converting to rear disc brakes under this rule. 3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes as stock from converting to rear disc brakes under this rule."
FP Add TB size to Ford Mustang (94-98) Spec Line
#39130 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP Ford Mustang (94-98) fuel injected throttle body inside diameter specified at 60.
In EP Spec Lines, Ford Mustang (94-98) add the following to the Fuel Injected Equipped Throttle Body Inside Diameter column: "60"
FP Correct Existing VW Scirocco Spec Line
#39140 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
fasterFP Volkswagen Scirocco: remove two engine variants (1715cc and 1780cc), lighten one variant to 1663 lbs, allow 15×7 wheels instead of 13×7.
In FP Spec Lines, Volkswagen Scirocco, change spec line as follows:
A specification table follows in the original; it is not shown here.
FP TR2 Notes E&O
#39180 from Anthony Parker · Rule change · TB 25-12 (2025-12 Fastrack)
unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.
In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes: "Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."
FP Balance of Power
#39187 from Jim Simaras · Rule change · TB 25-12 (2025-12 Fastrack)
slowerEP BMW Z3 2.5L restrictor reduced 52mm to 50mm, weight increased to 2550 lbs base; five other BMW models get smaller restrictors.
In EP Spec Lines, make the following changes to Restrictors: BMW Z3 2.5L: "52mm 50mm Flat Plate Intake Restrictor" BMW Z3 2.8L (97-00): "55mm 53mm Flat Plate Intake Restrictor" BMW 328i/is E36 (96-99): "58mm 55mm Flat Plate Intake Restrictor" BMW 328i/ci E46 (01-06): "58mm 55mm Flat Plate Intake Restrictor" BMW 325i/is (E46) (01-06): "56mm 53mm Flat Plate Intake Restrictor" BMW 325is M-Technic (1994): "56mm 53mm Flat Plate Intake Restrictor" BMW 325i/is E-36 (92-95): "56mm 53mm Flat Plate Intake Restrictor"
Show 4 more lines
In EP Spec Lines, BMW Z3 2.5L, change Weight as follows: "2500 2550 *2563 2614 **2625 2678"
FP Competition Adjustment Request
#39259 from David Strittmatter · Rule change · TB 25-12 (2025-12 Fastrack)
fasterFP Lancia Scorpion minimum weight drops 80 lbs, to 1950.
In FP Spec Lines, Lancia Scorpion, change Weight as follows: "2030 1950"
FP Factory Roll Bar Removal on VW Convertible
#39268 from Tim Linerud · Rule change · TB 25-12 (2025-12 Fastrack)
neutralFP Volkswagen Rabbit Convertible no longer required to remove factory roll bar.
In FP Spec Line, Volkswagen Rabbit (Includes Convertible), remove the following wording in Notes: "Factory roll bar must be removed on Cabriolet."
#38927 from Rock Beauchamp · Rule change · TB 26-01 (2026-01 Fastrack)
neutralFC USF2000 Tube Frame may use Hewland LD200 4-speed H-pattern as alternative to Hewland JL-200 5-speed sequential.
In FC Charts table, USF2000 Tube Frame spec line, add the following to the Notes: "Cars originally built with the Hewland LD200 4-speed H-pattern may use that transmission as an alternative to the Hewland JL- 200 5-speed sequential transmission."
FF Formula F Alternative Tire Rule Proposed Clarifications
#39281 from Jay Messenger · Rule change · TB 26-01 (2026-01 Fastrack)
neutralFF clarifies alternative tire eligibility for cars homologated 1989 or earlier with rocker arm or outboard suspension on all four corners.
In FF, GCR section 9.1.1.B.10.e, change as follows: "Alternatively, Formula F cars with rocker arm suspension (e.g., 1987-90 Reynard, Swift DB1,) and/or outboard suspension on at least one chassis end homologated in 1989 or earlier with any combination of rocker arm or outboard suspension on all four corners (e.g., 1987 – 1990 Reynard, Swift DB1) may use the following alternative tires. Note: This rule is intended to allow older cars with the described suspension design to use the alternative tires. It is not to be exploited by modifying cars with push-rods or pull-rods to meet the above requirements or by modifying either end of older cars to push- or pull-rod suspension to be eligible to run the alternative tires. Cars that were homologated in 1989 or earlier with push- or pull-rod suspension on no more than two corners may seek approval to run the alternative tire by utilizing the compliance process outlined in GCR section 8.1.4."
STL Weight adjustment for STL
#39579 from Super Touring Committee · Rule change · TB 26-01 (2026-01 Fastrack)
slowerSTL minimum weights increase across all classes, 1300 cc gains 195 lbs to 1950, up to 1850 cc at 2500.
In GCR, Section 9.1.4.2.H.1. change Minimum Weight on chart as follows:
A specification table follows in the original; it is not shown here.
FC Adjust F2000 Metrik ZF2 weight
#39612 from Club Racing Board · Rule change · TB 26-01 (2026-01 Fastrack)
fasterFC F2000 Metrik ZF2 minimum weight reduced to 1220 lbs.
In FC Charts table, F2000 Metrik ZF2 spec line, change the Weight as follows: "1240 1220"
FP Request Toyota 5E Series Engines
#38208 from Scott Schick · Rule change · TB 26-02 (2026-02 Fastrack)
neutralFP class adds Toyota 5E DOHC 1497cc engine, 1900 lbs minimum weight, 23mm SIR induction.
In FP Appendix N, add spec line for the Toyota 5E engine to the "Engines - TOYOTA" section:
A specification table follows in the original; it is not shown here.
FP Request for Toyota 4E Series Engines
#38209 from Scott Schick · Rule change · TB 26-02 (2026-02 Fastrack)
neutralFP Toyota 4E DOHC 1331cc engine added to Appendix N with 1900 lbs minimum weight.
In FP Appendix N, add spec line for the Toyota 4E engine to the "Engines - TOYOTA" section:
A specification table follows in the original; it is not shown here.
FP Dual Carbs for the Fiat X1/9
#39593 from Daniel Snow · Rule change · TB 26-02 (2026-02 Fastrack)
unclearFP Fiat X1/9 gains dual carburetor options with 28mm side-draft alternates and revised valve/transmission specs.
In FP Spec Lines, change as follows: Fiat X-1/9 & Bertone 1300: "(1) Weber 32 DMTR or DATRA/100 w/32mm bores (1) 40 DCNF w/32mm choke(s) (2) auto-type side-draft w/28mm choke(s) on I.R. manifold Orientation of the alternate carburetor is unrestricted. The alternate carb adapter may not be thicker than 1.25”. The adapter may have a bore larger than the throttle bore of the approved alternate carburetor. Valve Size: (I) 35.5/(1.40) (E) 31.3/(1.23)30.5/(1.20) (E) 1.23
Show 10 more lines
Trans. Speeds: 5" Fiat X-1/9 & Bertone: "Fuel Injection (1) 34 DMTR, (1) 36 DCNF w/34mm choke(s), or (1) 40DCNF w/34mm choke(s) (1) 36 or 40 DCNF w/34mm choke(s) (2) auto-type side-draft w/28mm choke(s) on I.R. manifold Orientation of the alternate carburetor is unrestricted. The alternate carb adapter may not be thicker than 1.25”. The adapter may have a bore larger than the throttle bore of the approved alternate carburetor. Valve Size: (I) 35.5/(1.40) (E) 33.0/(1.30) Trans. Speeds: 5 or 4"
What the rules allowed changed as listed; this does not say what any particular car ran.