This track has been raced on 2 configurations (The Circuit, 2.57 mi; 2.92 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One run is left out as not that car's own laps (far quicker than the car managed in any other session and than anyone else in its class all week; usually a swapped transponder): Tom Burt in Cal Club 2025 PM (1:42.300; the car's best in any other session was 1:52.334 and the rest of the class's best all week 1:50.233).
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
SCCA Ent SRF3
SRF3
38
1:50.233Caleb Shrader
1:50.233Caleb Shrader
1:50.825Caleb Shrader
138.9Paul Marino
30.136Caleb Shrader
31.672Caleb Shrader
44.841Tom Burt
Mazda Miata
STL
17
1:51.665Jared Korth
1:54.963Nick Leverone
1:54.845Gavin Wardle
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda MX-5
STL
6
1:51.665Jared Korth
1:57.404Ryan Gutile
1:54.845Gavin Wardle
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda Miata
STL
10
1:52.983Wesley Mollno
1:54.963Nick Leverone
1:55.682Nick Leverone
133.4Wesley Mollno
30.815Jon Davies
32.820Jon Davies
49.197Wesley Mollno
Mazda MX-5 (2015)
STL
1
2:00.239Adrian Comstock
2:00.239Adrian Comstock
2:00.722Adrian Comstock
133.0Adrian Comstock
32.847Adrian Comstock
34.493Adrian Comstock
52.675Adrian Comstock
Mazda RX-8
STL
1
1:53.515David LeCren
2:09.464David LeCren
2:11.372David LeCren
121.0David LeCren
31.217David LeCren
32.486David LeCren
49.550David LeCren
Honda Civic Si
STL
1
1:56.438Jonathan Lugod
1:57.331Jonathan Lugod
1:56.438Jonathan Lugod
106.8Jonathan Lugod
31.787Jonathan Lugod
33.468Jonathan Lugod
50.873Jonathan Lugod
Honda Prelude
STL
1
1:56.961Carl Young
1:57.917Carl Young
1:56.961Carl Young
104.5Carl Young
31.994Carl Young
33.745Carl Young
50.892Carl Young
Acura integra
STL
1
2:24.310Jack McEachern
2:24.310Jack McEachern
2:24.550Jack McEachern
77.6Jack McEachern
38.960Jack McEachern
41.141Jack McEachern
1:02.410Jack McEachern
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
SRF3 SRF3 Alternator Pulley Update In
#36095 from Robey Clark · Rule change · TB 24-06 (2024-06 Fastrack)
fasterSRF3 alternator pulley minimum weight reduced from 12 oz to 11 oz.
SFR3, GCR section 9.1.8.D.2.H.17, change as follows: "Alternator Pulley: P/N G902130, or P/N G902130A, or P/N G902131 (six row). 12 11 oz minimum weight."
SRF3 Update Rain Tire Rule and Hoosier Decal Placement
#36436 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)
slowerSRF wet tires: P185/60R13 H20/W2 option removed; P185/65R13 W2 front now required with P205/60R13 W2 rear.
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used. OR Front – Hoosier P/N 46101 P185/65R13 W2 Rear – Hoosier P/N 46105 P205/60R13 W2
Show 8 more lines
1. It is forbidden to regroove tires. 2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for violation will be the loss of qualifying times and/or the disqualification of race results. 3. Hoosier SRF/SRF3 Decal Placement: Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises."
SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info
#36624 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)
neutralSRF Hoosier decal requirement reduced from four decals in specific locations to three decals with simpler placement rules.
In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows: "Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
SRF3 Update SRF3 Air Filter Rule
#36681 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
unclearSRF3 air filter rule removes K&N RC-9160 option, leaving only P/N WM301020 allowed.
In SRF, GCR section 9.1.8.D.2.H.23, change as follows: "Air Filter: P/N WM301020 or K&N RC-9160"
SRF3 Update SRF Brake Rotor Thickness
#36687 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
slowerSRF brake rotor minimum thickness increases from 12.20mm to 13.25mm, Wilwood vented rotor P/N 800065.
In SRF, GCR section 9.1.8.D.1.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."
SRF3 Hoosier Tire Decal Placement
#36739 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
neutralSRF3 Hoosier logo placement changes from four decals to three decals in different locations.
In SRF, GCR section 9.1.8.D.2.B, change as follows: "Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."
STL Request to Remove Miata Hubs from General category
#37138 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)
neutralSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
In GCR, Section 9.1.4.M.18., change as follows: "18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."
Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21
SRF3 Driver Safety & Comfort
#37966 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)
neutralSRF drivers with disabilities may modify seat and controls for safety and comfort with approval and logbook notation.
In SRF, GCR section 9.1.8.D.1.D, add the following: "f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
SRF3 Update SADEV transmission specs
#37992 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)
unclearSTL Mazda MX5 Challenge minimum weight now references GCR 9.1.7.1 instead of 2500 lbs; spec components removed, only alternative tires allowed.
In STL Spec Lines, Table B, Mazda Spec MX5 Challenge, change as follows: Minimum Weight: "2500 See 9.1.7.1." Notes: "Mazda MX5 Challenge car must utilize the following components: Roush CNC cylinder head 0000-01-5300,Mahle standard or +0.005 0000-01-5310, OEM camshaft, 11:1 compression ratio, header 0000-06-5407-NC, exhaust 0000-06-5427-NC, cold air intake 0000- 06-5150-KT, ECU flash 0000-01-5379, Pagid front brake pads 0000-03-5104-SP or endurance pads 0000-03- 5104-EN, Pagid rear brake pads 0000-03-5114-SP or endurance pads 0000-03-5114-EN, Penske front shock 0000-04-5291-SA, Penske rear shock 0000-04-5292-SA, Penske rear mount kit 0000-04-5358, Front mount kit 0000-04-5359, Front offset bushing 0000-04-5407-NC, Eibach front springs 0000-04-9700-08, Eibach rear springs 0000-04-9400-07, Eibach helper springs 0000-04-
Show 5 more lines
9926, Eibach front sway bar 0000-04-5306-FT, Eibach rear sway bar 0000-04-5306-RR, Interior finish panels 0000-07-5822, C&R radiator/oil cooler assembly 0000-01-5504-CR, Oil cooler adapter and lines 0000-01-5511-KT, ACT clutch 0000-02-5004-G6, wheels 17x8 #0000-04-5706-GM, # 0000- 04-5706-SL, and Toyo RR 235-40-17 dry, Toyo RA1 235-40-17 wet. Alternative tires on 17x7 wheels per STL rules. No other Super Touring modifications or allowances permitted except as noted in this spec line. Must conform completely to GCR 9.1.7.1, except alternative tires (only) per STL regs allowed."
Applies to Mazda Miata on this page: Jared Korth, Ricardo Arruda, Gavin Wardle, Ryan Gutile, Bryce Johnson, Andy Chittum, Adrian Comstock
STL Lotus Weight Reduction
#38772 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)
fasterSTL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs.
In 9.1.2. GT2/ST Spec Lines, Lotus Evora GT4, change Weight as follows: "2750 2700" In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows: Lotus Elise Cup R: "2300 2250" Lotus Elise SC/ Lotus Exige SC: "2300 2550 2500 2450"
SRF3 SRF Rule Updates
#38853 from Robey Clark · Rule change · TB 25-09 (2025-09 Fastrack)
Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following: "SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual." Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038
Show 11 more lines
may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind; maximum of one spring per caliper. 1. Hawk Blue pads P/N 801993 only 2. Wilwood Vented Rotor P/N 800065 only, as delivered, with no machining of any kind. Minimum thickness 13.25mm (0.522") 3. Wilwood universal caliper Kit P/N 1180008 as delivered, caliper only P/N 800038; Wilwood knock back spring P/N 800045 may be used as delivered, with no machining of any kind, and only one spring per caliper 4. Renault caliper rubber bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185A 5. Renault caliper piston may be replaced with P/N 1196184 vented piston as delivered, with no machining of any kind 6. Girling .750" Master Cylinder P/N 880358 as delivered, with no machining of any kind 7. Wilwood .750" Master Cylinder P/N 880357 as delivered, with no machining of any kind 8. Tilton .750" Master Cylinder P/N 880360 as delivered, with no machining of any kind"
SRF3 Add HD Oil Cooler
#38979 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)
neutralSRF3 adds HD Oil Cooler P/N G1148500 as alternative to standard cooler P/N G480503.
In SRF, GCR section 9.1.8.D.1.V.ff, change as follows: "SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
STL Weight adjustment for STL
#39579 from Super Touring Committee · Rule change · TB 26-01 (2026-01 Fastrack)
slowerSTL minimum weights increase across all classes, 1300 cc gains 195 lbs to 1950, up to 1850 cc at 2500.
In GCR, Section 9.1.4.2.H.1. change Minimum Weight on chart as follows:
A specification table follows in the original; it is not shown here.
What the rules allowed changed as listed; this does not say what any particular car ran.