FF + GTX + SRF3 at Buttonwillow Raceway Park

2024-05-01 GTX Request for Spec Line 1010 Reconsideration

#35009 from Kristofer Olson · Rule change · TB 24-05 (2024-05 Fastrack)

In GT2-ST Spec Lines, Acura NSX, change as follows:
Minimum Weight: "2700 3000"
Restrictor: "43 45mm TIR"

2024-06-01 SRF3 SRF3 Alternator Pulley Update In

#36095 from Robey Clark · Rule change · TB 24-06 (2024-06 Fastrack)

SFR3, GCR section 9.1.8.D.2.H.17, change as follows:
"Alternator Pulley: P/N G902130, or P/N G902130A, or P/N G902131 (six row). 12 11 oz minimum weight."

2024-08-01 SRF3 Update Rain Tire Rule and Hoosier Decal Placement

#36436 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used.
OR
Front – Hoosier P/N 46101 P185/65R13 W2
Rear – Hoosier P/N 46105 P205/60R13 W2

2024-09-01 SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info

#36624 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows:
"Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose
to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1)
decal must be located on each side of the car and one (1) decal must be visible on the front."

2024-10-01 FF Update to FF EGR Blanking Plate Rule

#36633 from Matt Boian · Rule change · TB 24-10 (2024-10 Fastrack)

In FF, GCR section 9.1.1.B.14.r.1, change as follows:
"All emission control devices must be removed and blocked off by the blanking plate provided by HPD or Fast Forward as noted
below, except for the VTEC activation valve. The VTEC activation valve must be retained; and it must be functioning. No
modifications are permitted.
a. EGR Plate: Fast Forward PN: FF200-301.
b. EGR Port Cover: Fast Forward PN: FF200-302."

2024-10-01 SRF3 Update SRF3 Air Filter Rule

#36681 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.H.23, change as follows:
"Air Filter: P/N WM301020 or K&N RC-9160"

2024-10-01 SRF3 Update SRF Brake Rotor Thickness

#36687 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with
no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."

2024-10-01 SRF3 Hoosier Tire Decal Placement

#36739 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.B, change as follows:
"Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the
nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."

2024-11-01 FF Change FF/FC Weight with Sequential Gearbox

#36651 from Robert Wright · Rule change · TB 24-11 (2024-11 Fastrack)

In FF, GCR section 9.1.1.B.20.A.3, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
In FC, GCR section 9.1.1.B.20.B.4, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."

2024-11-01 FF Alternative Oversize Honda Fit Pistons

#37064 from Formula/Sports Racing Committee · Rule change · TB 24-11 (2024-11 Fastrack)

In FF, GCR section 9.1.1.B.14.e.1, change as follows:
"Honda Fit OEM standard size pistons, PN: 13010-RB1-000, or Honda Fit OEM 0.25mm oversize pistons, PN: 13020-RB7-Z00, or
Fast Forward 0.25mm oversize pistons, PN: FF800-110, may be used."
In GCR section 9.1.1.B.14.e.2, change as follows:
"a. Maximum standard piston diameter, measured at a point 16mm from the bottom of the skirt: 73.240mm
(2.8834 2.8835 inches).
b. Centerline of wrist pin to crown maximum: 26.21mm (1.032 inches).
c. Maximum overall height from skirt to crown edge: 47.80mm (1.882 inches).

2025-01-01 GTX Correct language regarding OEM Areo Devices

#37137 from Christopher Childs · Rule change · TB 25-01 (2025-01 Fastrack)

In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows:
"B. Aerodynamic Devices
2. Rear wing
c. The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level
with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule."

A specification table follows in the original; it is not shown here.

2025-03-01 FF Formula F Proposal to Invite Older Cars Via a Tire Rule Change

#37802 from Anthony Stefanelli · Rule change · TB 25-03 (2025-03 Fastrack)

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Formula F shall be limited to the following tires (front tires may not be used as rears):
Dries:
Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13
Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13
Wets:
Front - Hoosier Wet or W3 Radial 44421 185/60R13
Rear - Hoosier Wet or W3 Radial 44426 205/60R13

2025-04-01 SRF3 Driver Safety & Comfort

#37966 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.1.D, add the following:
"f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

2025-04-01 SRF3 Update SADEV transmission specs

#37992 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.2.K, change as follows:
"OR
SADEV-SRF3 6-Speed Sequential (beginning from Oct. 4, 2021 onward):
1st 12-36 3.0000 : 1
2nd 15-31 2.0667 : 1
3rd 18-28 1.5556 : 1
4th 22-28 1.2727 : 1
5th 24-26 1.0833 : 1

2025-05-01 GTX Request to Classify Porsche GT2 RS Clubsport

#37972 from Paul Fairchild · Rule change · TB 25-05 (2025-05 Fastrack)

In GTX, Classify Porsche GT2 RS Clubsport, as follows:
GTX
Make Homologation Model Restrictor
(mm)
Weight
(lbs) Notes
Porsche GT2 RS Clubsport Must have factory specifications available at all race events

2025-05-01 FF Page 228, FF tire rule 9.1.1.10.e

#38251 from Anthony Stefanelli · Rule change · TB 25-05 (2025-05 Fastrack)

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Formula F shall be limited to the following tires (front tires may not be used as rears):
Dries:
Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13
Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13
Wets:
Front - Hoosier Wet or W3 Radial 44421 185/60R13
Rear - Hoosier Wet or W3 Radial 44426 205/60R13

2025-06-01 GTX Ligier P3 LS Swap

#38164 from Bart Wolf · Rule change · TB 25-06 (2025-06 Fastrack)

In GTX Spec Lines, GTX-MISC., Ligier, LMP3, 3.0L, Add to Notes the following:
"Allow any normally aspirated LS Chevrolet engine may be used."

2025-09-01 SRF3 SRF Rule Updates

#38853 from Robey Clark · Rule change · TB 25-09 (2025-09 Fastrack)

Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following:
"SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil
Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no
machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber
caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced
with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038

2025-10-01 SRF3 Add HD Oil Cooler

#38979 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.V.ff, change as follows:
"SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan
permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."

2026-01-01 FF Formula F Alternative Tire Rule Proposed Clarifications

#39281 from Jay Messenger · Rule change · TB 26-01 (2026-01 Fastrack)

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Alternatively, Formula F cars with rocker arm suspension (e.g., 1987-90 Reynard, Swift DB1,) and/or outboard suspension on at
least one chassis end homologated in 1989 or earlier with any combination of rocker arm or outboard suspension on all four
corners (e.g., 1987 – 1990 Reynard, Swift DB1) may use the following alternative tires. Note: This rule is intended to allow older
cars with the described suspension design to use the alternative tires. It is not to be exploited by modifying cars with push-rods or
pull-rods to meet the above requirements or by modifying either end of older cars to push- or pull-rod suspension to be eligible to
run the alternative tires. Cars that were homologated in 1989 or earlier with push- or pull-rod suspension on no more than two
corners may seek approval to run the alternative tire by utilizing the compliance process outlined in GCR section 8.1.4."

2026-01-01 GTX Please Consider Adding a Spec Line to GTX Table 4 for the RCR T70

#39470 from Peter Jankovskis · Rule change · TB 26-01 (2026-01 Fastrack)

In GTX-Misc. Table 4, classify RCR70 Coupe:
GTX – MISC. TABLE 4
Make Homologation Model Restrictor

A specification table follows in the original; it is not shown here.