GT2 + SRF3 at Buttonwillow Raceway Park

2024-03-01 GT2 Classify Corvette C8 (2020- ) into GT2/ST

#33759 from Andrew Aquilante · Rule change · TB 24-03 (2024-03 Fastrack)

In GT2 Spec Lines, classify Chevrolet Corvette C8 (20-) as follows:
GT2-ST Maximum Displacement Minimum Weight Restrictor Notes
Chevrolet Corvette C8
(20-)
6162 3300 71mm -
Flat Plate
LT2 engine.

Applies to Chevrolet Corvette on this page: Igor Lyustin

2024-03-01 GT2 Requesting classification for a 2015 Mitjet ST in GT2

#35408 from Jim Froula · Rule change · TB 24-03 (2024-03 Fastrack)

In GT2 Spec Lines, GT Cars - MITJET ST, classify MITJET ST as follows:
GT Cars – MITJET ST
Model Years Body Style Drive-
line
Wheel-
base (in)
Notes
MITJET ST 2015 RWD 94.5 Must run per VTS specifications. Must have

2024-05-01 GT2 Request for Spec Line 1010 Reconsideration

#35009 from Kristofer Olson · Rule change · TB 24-05 (2024-05 Fastrack)

In GT2-ST Spec Lines, Acura NSX, change as follows:
Minimum Weight: "2700 3000"
Restrictor: "43 45mm TIR"

2024-05-01 GT2 Request to Eliminate the FPR from the Corvette (-2013) with LS2

#35878 from Michael Quattlebaum · Rule change · TB 24-05 (2024-05 Fastrack)

In GT2-ST Spec Lines, Chevrolet Corvette (14-19), change Restrictor as follows:
"78 80mm flat plate"

2024-06-01 SRF3 SRF3 Alternator Pulley Update In

#36095 from Robey Clark · Rule change · TB 24-06 (2024-06 Fastrack)

SFR3, GCR section 9.1.8.D.2.H.17, change as follows:
"Alternator Pulley: P/N G902130, or P/N G902130A, or P/N G902131 (six row). 12 11 oz minimum weight."

2024-07-01 GT2 GT2-ST Rule Clarification

#36093 from Dominic Starkweather · Rule change · TB 24-07 (2024-07 Fastrack)

In GCR Section, Appendix K. 2012.M2, add the following:
"After market replacement differential housings are permitted as long as they are an exact equivalent."

2024-07-01 GT2 GT4 cars may run in GT2-ST

#36235 from Grand Touring Committee · Rule change · TB 24-07 (2024-07 Fastrack)

In 9.1.2. GT2 Spec Lines, GT3 Cars, change Note as follows:
"Note: All GT4 cars are permitted to compete in GT2-ST provided they use a factory supplied power stick or Pro Series
required restrictor. Must have GT4 rules in possession at all race events. Cars must comply with 2012 STO rules as
stated in Appendix K of the GCR. Engine Displacements in this table are nominal. Each competitor shall have available
definitive documentation (e.g., factory manual) of the original displacement for the engine used. Slicks allowed on all
GT2/ST cars with a 100-pound weight penalty."

2024-08-01 SRF3 Update Rain Tire Rule and Hoosier Decal Placement

#36436 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used.
OR
Front – Hoosier P/N 46101 P185/65R13 W2
Rear – Hoosier P/N 46105 P205/60R13 W2

2024-09-01 SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info

#36624 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows:
"Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose
to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1)
decal must be located on each side of the car and one (1) decal must be visible on the front."

2024-10-01 SRF3 Update SRF3 Air Filter Rule

#36681 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.H.23, change as follows:
"Air Filter: P/N WM301020 or K&N RC-9160"

2024-10-01 SRF3 Update SRF Brake Rotor Thickness

#36687 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with
no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."

2024-10-01 SRF3 Hoosier Tire Decal Placement

#36739 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.B, change as follows:
"Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the
nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."

2025-01-01 GT2 Panoz Esperante GTS BOP

#36686 from Brian Goldburg · Rule change · TB 25-01 (2025-01 Fastrack)

In GT2 SPEC LINES, GT Engines - PANOZ, classify 2013-2016 Ford EcoBoost Twin Turbo as follows:
GT Engines – PANOZ
Engine
Family
Engine Type Bore x
Stroke
(in.)
Disp.

A specification table follows in the original; it is not shown here.

2025-01-01 GT2 Correct language regarding OEM Areo Devices

#37137 from Christopher Childs · Rule change · TB 25-01 (2025-01 Fastrack)

In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows:
"B. Aerodynamic Devices
2. Rear wing
c. The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level
with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule."

A specification table follows in the original; it is not shown here.

2025-01-01 GT2 GT2 Sunbeam Tiger Alternate Carburetor

#37198 from Tom Patton · Rule change · TB 25-01 (2025-01 Fastrack)

In GT2 Spec Lines, GT Engines - SUNBEAM, add to Fuel Induction as follows:
"Carburetors(s) Holly 650 cfm PN #80541-1 and PN #80541-2"

2025-02-01 GT2 GT2/ST - Remove Aftermarket/Racing ABS penalty

#36538 from Jorge A Nazario · Rule change · TB 25-02 (2025-02 Fastrack)

In GCR, Appendix K. 2012 STO Rules, O.9., change as follows:
"May run OEM ABS or convert to an aftermarket ABS controller with 100 50 lb. weight penalty."

2025-03-01 GT2 Hood Bulge allowed

#37000 from Gordon Leslie · Rule change · TB 25-03 (2025-03 Fastrack)

In GT2 Spec Lines, GT2 Cars - PONTIAC, Fiero, change as follows:
Drive-line: "FWD RWD"
Add to Notes: "Hood bulge permitted as requested for front engine relocation only."

2025-03-01 GT2 OEM Wing Adjustment

#37590 from Christopher Childs · Rule change · TB 25-03 (2025-03 Fastrack)

In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows:
"The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of
the roof. OEM aerodynamic devices do not need to adhere to the height rule."
In GCR, Section APPENDIX K. 2012 STO GENERAL TECHNICAL REGULATIONS, D.4.b., add the following:
"Factory wings, and spoilers, and roof vortex generators are permitted, but must be removed if an approved aftermarket wing is
installed. OEM aerodynamic devices do not need to adhere to the height rule."

2025-04-01 SRF3 Driver Safety & Comfort

#37966 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.1.D, add the following:
"f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

2025-04-01 SRF3 Update SADEV transmission specs

#37992 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.2.K, change as follows:
"OR
SADEV-SRF3 6-Speed Sequential (beginning from Oct. 4, 2021 onward):
1st 12-36 3.0000 : 1
2nd 15-31 2.0667 : 1
3rd 18-28 1.5556 : 1
4th 22-28 1.2727 : 1
5th 24-26 1.0833 : 1

2025-08-01 GT2 Rear Deck Lid for Older Air-Cooled Porsche

#38506 from Justin Erion · Rule change · TB 25-08 (2025-08 Fastrack)

In GT2 Spec Lines, GT2 Cars-Porsche, 911 Coupe & Targa., add to Notes the following:
"Porsche 911-based race cars (911,963,994), the use of the 993 3.8 RSR rear deck lid/spoiler is permitted. Aftermarket
reproductions of the original Porsche Motorsports deck lid provided they faithfully replicate OEM dimensions and functionality,
are acceptable for use."

2025-09-01 SRF3 SRF Rule Updates

#38853 from Robey Clark · Rule change · TB 25-09 (2025-09 Fastrack)

Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following:
"SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil
Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no
machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber
caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced
with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038

2025-10-01 SRF3 Add HD Oil Cooler

#38979 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.V.ff, change as follows:
"SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan
permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."

2026-01-01 GT2 Additional Body Options to Replace Older Stock Car Bodies

#39086 from Samuel Daniels · Rule change · TB 26-01 (2026-01 Fastrack)

In GCR, Section 4.8.4.2.1., add the following:
"Cars in the class must use 1997, through current year, commercially available stock car bodywork. The following make/model
bodies are allowed:
1. Cadillac CTS
2. Chevrolet Impala
3. Chevrolet Malibu
4. Chevrolet Monte Carlo
5. Chevrolet SS

2026-01-01 GT2 GT3 Turbo to GT2?

#39365 from Chris Edens · Rule change · TB 26-01 (2026-01 Fastrack)

In GT2 Spec Lines, Engines - MAZDA, classify Engine Family BP as follows:
GT2 Engines - MAZDA
Engine
Family
Engine Type Bore x Stroke
(mm)
Disp.
(CC)

A specification table follows in the original; it is not shown here.

2026-01-01 GT2 Tech Bulletins for GT2 and GT2-ST

#39537 from Grand Touring Committee · Rule change · TB 26-01 (2026-01 Fastrack)

In GT2 Spec Lines, GT2 Cars – Porsche, classify 992.1 GT3 Cup as follows:
GT2 Cars – Porsche
Model Year Body
Style Driveline Wheel Base Notes
992.1
GT3 Cup
(22-25) 2 Dr RWD 4.0L flat six. 3250lbs. w/60mm Throttle Body Restrictor (TBR).
Cars must be prepared in accordance with the appropriate

2026-02-01 GT2 Allow Larger Air Cooled Engines in Porsche 911 GT2

#39249 from Justin Erion · Rule change · TB 26-02 (2026-02 Fastrack)

In GT Spec Lines, create GT Cars - PORSCHE and classify SC as follows:
GT Cars - PORSCHE
Model Years Body Style Drive- line Wheel- base
(in)
Notes
SC 1978 2 Dr. Rear engine/RWD 89.45 May use alternate engine bore.
4.0L 2V @2275 lbs. 4.0L 4V @ 2350 lbs.

2026-02-01 GT2 Classify T1 BMW in GT2

#39408 from Jared Lendrum · Rule change · TB 26-02 (2026-02 Fastrack)

In GT Spec Lines, classify M3 E92 in GT Cars - BMW as follows:
GT Cars - BMW
Model Years Body Style Drive-
line
Wheel-
base (in)
Notes
M3 E92 (08-13) 2 Dr. RWD 108.7 Cannot be built to any other rule set.

A specification table follows in the original; it is not shown here.