BoP Lab / Buttonwillow Raceway Park

HP + SMX + T2 at Buttonwillow Raceway Park

No mapCal Club 2024, Cal Club 2023

This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.

One session is left out because the timing does not look like full laps: Cal Club 2023 Qualifying #2.

Pos	Car	Driver	Class	#	Lap	Theoretical	Qual	Race	5-lap stint	Consistency	Trap	S1	S2	S3
1	MG Midget	Bill Okell	HP	7	1:40.295 B-P	1:40.261	2:07.503 B-Q1	2:04.195 A-R2	2:04.781 A-R2	+2.144 A-R2	116.4 B-P	27.543 B-P	28.857 B-P	43.861 B-P
2	Honda Civic TCR	Rylan Hazelton	T2	49	1:51.198 A-Q1	1:50.763	1:51.198 A-Q1	1:51.454 A-R1	1:51.718 A-R1	+1.803 A-R1	140.1 A-R1	30.640 A-Q1	31.962 A-Q1	48.161 A-R1
3	Chevrolet	Oli Thordarson 2+ cars	T2	121, 122	1:52.045 B-P	1:51.914	1:54.065 B-Q1	1:52.758 B-R1	1:53.593 B-R1	+0.980 B-R1	114.9 B-P	30.654 B-P	32.604 B-R1	48.656 B-P
4	Chevrolet Corvette	Josh Carroll	T2	35	1:52.276 A-Q2	1:51.896	1:52.276 A-Q2	1:52.993 A-R2	1:53.334 A-R2	+1.248 A-R2	144.5 A-Q2	30.813 A-Q2	32.300 A-Q1	48.783 A-P
5	Chevrolet Corvette	David Holmes	T2	171	1:52.705 A-Q2	1:52.489	1:52.705 A-Q2	1:53.499 A-R1	1:54.684 A-R2	+1.099 A-R2	143.9 A-Q2	30.883 A-Q1	32.407 A-Q2	49.199 A-Q2
6	Chevrolet Chevrolet	Oli Thordarson 2+ cars	T2	122	1:53.309 A-Q2	1:53.051	1:53.309 A-Q2	1:54.433 A-R1	1:55.036 A-R2	+0.674 A-R2	142.9 A-R1	31.173 A-P	32.798 A-Q1	49.080 A-P
7	Chevrolet Corvette Z06	Greg Nester	T2	32	1:53.653 A-Q2	1:53.567	1:53.653 A-Q2	1:54.838 A-R1	1:55.189 A-R2	+0.472 A-R2	135.9 A-R1	31.106 A-Q2	32.902 A-Q2	49.559 A-Q2
8	Chevrolet Corvette	Patrick Howe	T2	03	1:53.679 A-P	1:53.373	1:54.829 A-Q1	1:55.392 A-R2	1:56.107 A-R2	+1.043 A-R2	146.6 A-Q2	31.124 A-Q1	33.112 A-Q1	49.137 A-P
9	Chevrolet Corvette	Evan Gold	T2	37	1:53.749 A-R1	1:53.155	1:53.792 A-Q2	1:53.749 A-R1	1:55.163 A-R2	+0.789 A-R2	138.7 A-Q1	31.295 A-R1	32.797 A-Q2	49.063 A-R1
10	Chevrolet Corvette Z06	Michael Cheney	T2	17	1:54.983 A-R2	1:54.489	1:55.079 A-Q1	1:54.983 A-R2	1:55.791 A-R2	+1.987 A-R2	138.0 A-Q1	31.504 A-Q1	33.215 A-Q1	49.770 A-Q1
11	Ford Mustang GT	Scotty B White	T2	0	1:55.309 A-Q1	1:55.233	1:55.309 A-Q1	1:56.025 A-R1	1:56.446 A-R1	+0.956 A-R1	133.2 A-R1	31.540 A-Q1	33.554 A-R1	50.139 A-Q1
12	Chevrolet C5 Z06	Luis Martinez	T2	77	1:55.450 A-R1	1:54.548	1:55.662 A-Q1	1:55.450 A-R1	1:56.522 A-R1	+3.951 A-R1	129.8 A-R1, A-Q2	31.045 A-R1	33.509 A-R1	49.994 A-R1
13	Mazda MX-5 (2006)	Ethan Lampe	SMX	95	1:56.431 B-Q2	1:56.371	1:56.431 B-Q2	1:57.417 B-R2	1:57.634 B-R2	+0.462 B-R2	109.8 B-R2	31.777 B-Q1	33.620 B-Q2	50.974 B-Q2
14	Mazda MX-5 (2013)	Lincoln Larson	SMX	12	1:56.503 A-Q2	1:56.503	1:56.503 A-Q2	1:59.141 A-R1	2:00.335 A-R1	+1.234 A-R1	132.0 A-Q1	31.834 A-P	33.724 A-P	51.178 A-Q2
15	Mazda MX-5 (2006)	Jared Korth	SMX	27	1:56.725 A-Q1	1:56.687	1:56.725 A-Q1	1:58.159 B-R2	1:58.422 B-R2	+0.652 B-R2	136.3 A-Q1	31.924 B-P	33.696 A-Q1	51.067 A-Q1
16	Mazda MX-5 (2006)	William Wallis	SMX	52	1:56.947 A-Q1	1:56.891	1:56.947 A-Q1	1:57.973 A-R1	1:58.799 A-R1	+0.935 A-R1	130.3 A-Q1	31.888 A-Q1	33.647 A-Q1	51.356 A-Q1
17	Mazda MX-5 (2012)	Emy Kissick 2+ cars	SMX	13	1:57.010 A-Q2	1:57.010	1:57.010 A-Q2	1:58.594 A-R2	1:59.304 A-R2	+1.778 A-R2	133.6 A-R2	32.035 A-Q1	33.967 A-Q1	51.449 A-Q2
18	Mazda MX-5	Cooper Hicks	SMX	86	1:57.154 B-Q2	1:57.015	1:57.154 B-Q2	1:58.319 B-R1	1:58.608 B-R2	+0.507 B-R2	109.2 B-Q2	31.969 B-Q2	33.832 B-P	51.214 B-P
19	Mazda MX-5 (2008)	Christian Hoagland 2+ cars	SMX	01	1:57.195 A-Q2	1:56.921	1:57.195 A-Q2	1:58.021 A-R2	1:58.465 A-R2	+1.234 A-R2	136.1 A-Q1	31.987 A-Q1	33.897 A-P	51.037 A-Q2
20	Mazda Miata	Christian Hoagland 2+ cars	SMX	01	1:57.211 B-P	1:57.077	1:57.885 B-Q2	1:58.294 B-R1	1:58.923 B-R1	+0.703 B-R1	108.8 B-P	31.959 B-P	33.927 B-P	51.191 B-P
21	Mazda MX-5 (2006)	Joey Andrews	SMX	111	1:57.436 A-Q1	1:57.401	1:57.436 A-Q1	1:58.757 A-R1	1:59.377 A-R1	+1.179 A-R1	141.6 A-Q2	32.124 A-Q1	33.813 A-Q1	51.464 A-Q1
22	Mazda MX-5 (2006)	Ryan Gutile	SMX	116	1:57.463 A-Q1	1:57.339	1:57.463 A-Q1	1:58.772 A-R2	1:59.460 A-R2	+1.350 A-R2	133.6 A-R2	31.905 A-Q1	33.939 A-Q1	51.495 A-Q2
23	Mazda MX-5 (2012)	Gavin Wardle	SMX	169	1:57.612 A-Q2	1:57.484	1:57.612 A-Q2	1:59.220 A-R2	1:59.535 A-R2	+1.183 A-R2	133.4 A-Q2	32.082 A-Q2	33.863 A-Q2	51.539 A-Q2
24	Mazda Miata (2006)	Wesley Mollno 2+ cars	SMX	111	1:57.853 B-Q2	1:57.745	1:57.853 B-Q2	1:59.001 B-R2	1:59.340 B-R2	+0.516 B-R2	112.1 B-R2	32.080 B-Q2	34.047 B-Q2	51.618 B-Q2
25	Mazda MX-5 (2008)	Aidan Shimbashi	SMX	72	1:57.891 A-Q2	1:57.704	1:57.891 A-Q2	1:58.739 A-R2	1:59.436 A-R2	+1.672 A-R2	132.3 A-R2	32.361 A-P	33.812 A-Q2	51.531 A-Q2
26	Mazda MX-5 (2010)	Bryce Johnson	SMX	15	1:58.391 A-Q1	1:58.089	1:58.391 A-Q1	1:59.447 A-R2	1:59.635 A-R2	+0.805 A-R2	134.6 A-Q1	32.180 A-Q1	34.098 A-Q1	51.811 A-Q1
27	Mazda MX-5 (2006)	Wesley Mollno 2+ cars	SMX	11	1:58.556 A-Q2	1:58.556	1:58.556 A-Q2	1:59.393 A-R1	2:00.401 A-R1	+1.119 A-R1	132.7 A-R1	32.515 A-P	34.154 A-Q1	52.048 A-Q2
28	Mazda Miata (2007)	Jon Davies	SMX	67	1:58.557 B-Q1	1:57.943	1:58.557 B-Q1	1:59.608 B-R1	2:00.014 B-R1	+0.514 B-R1	110.0 B-Q1	32.013 B-Q2	34.314 B-Q2	51.616 B-Q1
29	Mazda MX-5 (2010)	Thomas Bellemin	SMX	25	1:58.671 B-P	1:58.245	1:59.087 B-Q2	1:59.878 B-R2	2:00.063 B-R2	+0.552 B-R2	109.8 B-Q2	32.172 B-P	34.074 B-P	51.999 B-Q2
30	Mazda Miata (2007)	Patrick Drinkwine	SMX	151	1:58.954 B-Q2	1:58.586	1:58.954 B-Q2	1:59.848 B-R2	2:00.219 B-R2	+1.257 B-R2	112.1 B-R1	32.431 B-Q2	34.268 B-Q2	51.887 B-Q2
31	Mazda Miata (2012)	Emy Kissick 2+ cars	SMX	13	1:59.056 B-Q2	1:58.909	1:59.056 B-Q2	2:00.430 B-R1	2:00.784 B-R1	+1.110 B-R1	106.6 B-Q1	32.502 B-Q2	34.381 B-Q2	52.026 B-Q2
32	Mazda MX-5 (2007)	Andy Chittum	SMX	99	1:59.575 A-Q2	1:59.340	1:59.575 A-Q2	2:00.160 A-R2	2:00.656 A-R2	+0.703 A-R2	132.0 A-R2	32.538 A-R2	34.495 A-P	52.307 A-Q2
33	Mazda MX-5 (2008)	Ricardo Arruda	SMX	16	1:59.640 B-Q1	1:59.390	1:59.640 B-Q1	2:01.351 B-R1	2:01.755 B-R1	+1.041 B-R1	103.3 B-Q1	32.407 B-Q1	34.430 B-Q1	52.553 B-Q1
34	Mazda MX5 (2010)	Michael Travers	SMX	132	2:00.055 B-R1	1:59.884	2:00.568 B-Q1	2:00.055 B-R1	2:00.511 B-R1	+0.738 B-R1	115.3 B-P	32.815 B-R2	34.508 B-R1	52.561 B-R1
35	Mazda MX-5 (2015)	Adrian Comstock	SMX	25	2:00.330 A-Q2	2:00.182	2:00.330 A-Q2	2:00.678 A-R2	2:01.159 A-R2	+0.837 A-R2	132.0 A-R2	32.913 A-R2	34.721 A-R2	52.548 A-Q2
36	Mazda MX-5 (2006)	Richard James 2+ cars	SMX	91	2:01.402 A-Q1	2:01.353	2:01.402 A-Q1	2:02.469 A-R2	2:02.925 A-R2	+1.646 A-R2	126.2 A-R2	32.979 A-Q1	34.982 A-Q1	53.392 A-Q1
37	Mazda MX-5 (2006)	Amy Mills	SMX	2	2:01.543 A-Q2	2:01.543	2:01.543 A-Q2	2:02.512 A-R2	2:03.543 A-R2	+1.667 A-R2	122.0 A-R2	33.434 A-Q1	34.905 A-Q1	53.264 A-Q2
38	Mazda Miata (2006)	Richard James 2+ cars	SMX	91	2:01.677 B-Q2	2:01.450	2:01.677 B-Q2	2:01.929 B-R2	2:03.109 B-R2	+1.515 B-R2	106.1 B-Q2	32.922 B-R2	35.072 B-Q2	53.456 B-R2
39	MG Midget	Lee Fleming >115%	HP	00	2:03.082 B-R1	2:00.418	2:05.170 A-Q1	2:03.082 B-R1	2:04.295 A-R1	+1.090 A-R1	126.2 A-R2	30.556 A-Q1	35.463 B-R1	54.399 A-R1
40	MG Midget	Brian Linn >115%	HP	48	2:03.551 A-R1	2:03.219	2:04.965 A-Q1	2:03.551 A-R1	2:04.243 A-R1	+0.928 A-R1	121.0 A-R1	33.172 A-R1	35.274 A-R1	54.773 A-R1
41	MG Midget	Noel Hayward >115%	HP	2	2:04.870 B-R2	2:04.711		2:04.870 B-R2	2:10.679 B-R1	+4.104 B-R1	99.2 B-R2	33.577 B-R2	36.471 B-R2	54.663 B-R2
42	Toyota Yaris	Bobby Beyer >115%	HP	18	2:08.224 B-R2	2:08.010	2:10.927 B-Q1	2:08.224 B-R2	2:09.636 B-R2	+2.098 B-R2	92.3 B-R2	34.660 B-R2	37.206 B-R2	56.144 B-R2
43	Mini Cooper	Tom Tuttle >115%	HP	42	2:09.238 B-R2	2:08.416	2:11.042 B-Q1	2:09.238 B-R2	2:10.173 B-R1	+1.249 B-R1	99.0 B-R2	34.631 B-R1	37.306 B-R1	56.479 B-R2

One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it. Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.

Sectors

S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi

Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.

By car

Car	Class	Drivers	Lap	Qual	Race	Trap	S1	S2	S3
MG Midget	HP	4	1:40.295Bill Okell	2:04.965Brian Linn	2:03.082Lee Fleming	126.2Lee Fleming	27.543Bill Okell	28.857Bill Okell	43.861Bill Okell
Honda Civic TCR	T2	1	1:51.198Rylan Hazelton	1:51.198Rylan Hazelton	1:51.454Rylan Hazelton	140.1Rylan Hazelton	30.640Rylan Hazelton	31.962Rylan Hazelton	48.161Rylan Hazelton
Chevrolet	T2	1	1:52.045Oli Thordarson	1:54.065Oli Thordarson	1:52.758Oli Thordarson	114.9Oli Thordarson	30.654Oli Thordarson	32.604Oli Thordarson	48.656Oli Thordarson
Chevrolet Corvette	T2	7	1:52.276Josh Carroll	1:52.276Josh Carroll	1:52.993Josh Carroll	146.6Patrick Howe	30.813Josh Carroll	32.300Josh Carroll	48.783Josh Carroll
Chevrolet Corvette	T2	4	1:52.276Josh Carroll	1:52.276Josh Carroll	1:52.993Josh Carroll	146.6Patrick Howe	30.813Josh Carroll	32.300Josh Carroll	48.783Josh Carroll
Chevrolet Corvette Z06	T2	2	1:53.653Greg Nester	1:53.653Greg Nester	1:54.838Greg Nester	138.0Michael Cheney	31.106Greg Nester	32.902Greg Nester	49.559Greg Nester
Chevrolet C5 Z06	T2	1	1:55.450Luis Martinez	1:55.662Luis Martinez	1:55.450Luis Martinez	129.8Luis Martinez	31.045Luis Martinez	33.509Luis Martinez	49.994Luis Martinez
Chevrolet Chevrolet	T2	1	1:53.309Oli Thordarson	1:53.309Oli Thordarson	1:54.433Oli Thordarson	142.9Oli Thordarson	31.173Oli Thordarson	32.798Oli Thordarson	49.080Oli Thordarson
Ford Mustang	T2	1	1:55.309Scotty B White	1:55.309Scotty B White	1:56.025Scotty B White	133.2Scotty B White	31.540Scotty B White	33.554Scotty B White	50.139Scotty B White
Mazda MX-5	SMX	20	1:56.431Ethan Lampe	1:56.431Ethan Lampe	1:57.417Ethan Lampe	141.6Joey Andrews	31.777Ethan Lampe	33.620Ethan Lampe	50.974Ethan Lampe
Mazda MX-5 (2006)	SMX	8	1:56.431Ethan Lampe	1:56.431Ethan Lampe	1:57.417Ethan Lampe	141.6Joey Andrews	31.777Ethan Lampe	33.620Ethan Lampe	50.974Ethan Lampe
Mazda MX-5 (2013)	SMX	1	1:56.503Lincoln Larson	1:56.503Lincoln Larson	1:59.141Lincoln Larson	132.0Lincoln Larson	31.834Lincoln Larson	33.724Lincoln Larson	51.178Lincoln Larson
Mazda MX-5 (2012)	SMX	2	1:57.010Emy Kissick	1:57.010Emy Kissick	1:58.594Emy Kissick	133.6Emy Kissick	32.035Emy Kissick	33.863Gavin Wardle	51.449Emy Kissick
Mazda MX-5	SMX	1	1:57.154Cooper Hicks	1:57.154Cooper Hicks	1:58.319Cooper Hicks	109.2Cooper Hicks	31.969Cooper Hicks	33.832Cooper Hicks	51.214Cooper Hicks
Mazda MX-5 (2008)	SMX	3	1:57.195Christian Hoagland	1:57.195Christian Hoagland	1:58.021Christian Hoagland	136.1Christian Hoagland	31.987Christian Hoagland	33.812Aidan Shimbashi	51.037Christian Hoagland
Mazda MX-5 (2010)	SMX	2	1:58.391Bryce Johnson	1:58.391Bryce Johnson	1:59.447Bryce Johnson	134.6Bryce Johnson	32.172Thomas Bellemin	34.074Thomas Bellemin	51.811Bryce Johnson
Mazda MX-5 (2007)	SMX	1	1:59.575Andy Chittum	1:59.575Andy Chittum	2:00.160Andy Chittum	132.0Andy Chittum	32.538Andy Chittum	34.495Andy Chittum	52.307Andy Chittum
Mazda MX5 (2010)	SMX	1	2:00.055Michael Travers	2:00.568Michael Travers	2:00.055Michael Travers	115.3Michael Travers	32.815Michael Travers	34.508Michael Travers	52.561Michael Travers
Mazda MX-5 (2015)	SMX	1	2:00.330Adrian Comstock	2:00.330Adrian Comstock	2:00.678Adrian Comstock	132.0Adrian Comstock	32.913Adrian Comstock	34.721Adrian Comstock	52.548Adrian Comstock
Mazda Miata	SMX	6	1:57.211Christian Hoagland	1:57.853Wesley Mollno	1:58.294Christian Hoagland	112.1Wesley Mollno	31.959Christian Hoagland	33.927Christian Hoagland	51.191Christian Hoagland
Mazda Miata	SMX	1	1:57.211Christian Hoagland	1:57.885Christian Hoagland	1:58.294Christian Hoagland	108.8Christian Hoagland	31.959Christian Hoagland	33.927Christian Hoagland	51.191Christian Hoagland
Mazda Miata (2006)	SMX	2	1:57.853Wesley Mollno	1:57.853Wesley Mollno	1:59.001Wesley Mollno	112.1Wesley Mollno	32.080Wesley Mollno	34.047Wesley Mollno	51.618Wesley Mollno
Mazda Miata (2007)	SMX	2	1:58.557Jon Davies	1:58.557Jon Davies	1:59.608Jon Davies	112.1Patrick Drinkwine	32.013Jon Davies	34.268Patrick Drinkwine	51.616Jon Davies
Mazda Miata (2012)	SMX	1	1:59.056Emy Kissick	1:59.056Emy Kissick	2:00.430Emy Kissick	106.6Emy Kissick	32.502Emy Kissick	34.381Emy Kissick	52.026Emy Kissick
Toyota Yaris	HP	1	2:08.224Bobby Beyer	2:10.927Bobby Beyer	2:08.224Bobby Beyer	92.3Bobby Beyer	34.660Bobby Beyer	37.206Bobby Beyer	56.144Bobby Beyer
Mini Cooper	HP	1	2:09.238Tom Tuttle	2:11.042Tom Tuttle	2:09.238Tom Tuttle	99.0Tom Tuttle	34.631Tom Tuttle	37.306Tom Tuttle	56.479Tom Tuttle

The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.

Rule changes between these events

Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23

2023-03-01 T2 Honda Civic Type R Tire Size Increase

#33672 from Marty Grand · Rule change · TB 23-03 (2023-03 Fastrack)

Summary

fasterT2 Honda Civic Type-R tire size increases from 275 to 295.

As printed in Fastrack

In T2 Spec Lines, Honda Civic Type-R (2017-), change Tire Size as follows:
"~~275~~ 295"

2023-04-01 T2 Allowance of any nonmetallic bushing material in T2

#33833 from Tyler Quance · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

suspension & brakesT2 upper and lower control arm bushings can now use polyurethane, delrin, or alternate synthetic materials.

As printed in Fastrack

In Touring (T2-T5) Category Specifications, GCR Section 9.1.9.2.D.5.c.1., change as follows:
"All T2-T3 cars are allowed to replace OEM upper and lower control arm bushings with polyurethane, or delrin, or alternate
synthetic material~~bushings~~."

2023-04-01 T2 Allow Adjustable stabilizer bar links

#33861 from John Heinricy · Rule change · TB 23-04 (2023-04 Fastrack)

Summary

suspension & brakesT2 Cadillac CT4-V Blackwing now permits adjustable sway bar end links.

As printed in Fastrack

In T2 Spec Lines, Cadillac CT4-V Blackwing (2022-), add to Notes as follows:
"Adjustable sway bar end links permitted."

2023-05-01 T2 C5 Z06 Straight Line Speed

#33575 from Charlie Abell · Rule change · TB 23-05 (2023-05 Fastrack)

Summary

slowerT2 Chevrolet Corvette C5 Z06 restrictor increases from 53mm to 56mm; 58mm option removed.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04), change Weight (lbs) as follows:
"3425 w/~~53mm~~ 56mm flat plate restrictor)
~~3350 (w/58mm flat plate restrictor, only permitted when using OEM Wheels and Stock Brakes)~~"

Applies to Chevrolet Corvette on this page: Josh Carroll, David Holmes, Patrick Howe, Evan Gold, Greg Nester, Michael Cheney, Luis Martinez

2023-06-01 T2 2009 Porsche Cayman Classing Request

#34147 from Lisa Hunsicker · Rule change · TB 23-06 (2023-06 Fastrack)

Summary

wordingT2 Porsche Cayman S model year range extended from 06-08 to 06-09.

As printed in Fastrack

In T2 Spec Lines, Porsche Cayman S (06-08), change year as follows:
"Porsche Cayman S ~~(06-08)~~ (06-09)"

2023-06-01 HP Request to Classify Sonic and Fiesta in HP

#34264 from Greg Amy · Rule change · TB 23-06 (2023-05 Fastrack)

Summary

wordingFord Fiesta HP and Chevrolet Sonic FP model year ranges extended from 2016 to 2019.

As printed in Fastrack

In HP, adjust model years of the "Ford Fiesta (11-16)" spec line as follows:
"Ford Fiesta (11-16 9)"
In FP, adjust model years of the "Chevrolet Sonic (12-16)" spec line as follows:
"Chevrolet Sonic (12-16 9)"

2023-07-01 HP ITC to FP?

#34286 from David Snow · Rule change · TB 23-06 (2023-07 Fastrack)

Summary

cars addedHP Volkswagen Rabbit Cabriolet 1780 removed; Rabbit 1588 and 1715 reclassified with engine sizes and year ranges specified.

As printed in Fastrack

In HP Spec Lines, Volkswagen Rabbit Cabriolet 1780, delete in its entirely:
In HP, Spec Lines, Volkswagen Rabbit, change Title as follows:
“Volkswagen Rabbit 1588 ~~(includes Cabriolet / convertible)~~”
“Volkswagen Rabbit 1715 ~~(81-84) (excl. conv.)~~”
“Volkswagen Rabbit ~~GTI~~ 1780 ~~(83-84)~~”

2023-07-01 T2 370Z Obsolete Parts & NISMO Alternatives to SPL Parts

#34297 from Zach Hayward · Rule change · TB 23-06 (2023-05 Fastrack)

Summary

wordingT2 Nissan 370Z allows NISMO suspension alternatives to SPL parts; rear toe arms removed from permitted list.

As printed in Fastrack

In T2 Spec Lines, Nissan 370Z (09-17) / 370Z NISMO Edition (09-17), change Notes as follows:
5300S-SS370 T-2 spring kit allowed; ~~54600-SS370 T-2 front and rear sway bar kit allowed.~~ Sway Bars allowed 35mm (f). 29mm
(r). Sports Package is allowed. Springs up to 1000 lbs/in front and rear allowed. 54010- SZ350 (F) and 55020-SZ350 (R) allowed.
Cold Air Intake allowed. Performance Alternative Header permitted - ~~Part #14002-SS370.~~ Rear spring relocation permitted to
allow coil over shocks. SPL suspension kit permitted that includes: rear camber arms #SPL RLL Z34 or Nismo 551A0-RLLRZ, ~~SPL~~
~~rear toe arms #SPL RTA Z34~~, SPL rear traction arms #SPL RTR Z34 or Nismo 55110-RTRRZ, SPL front camber arms #SPL FUA Z34 or
54525-FUAZ4, SPL rear mid link #SPL RML Z34 or Nismo 551B0-RMLZ4. Zspeed and Z1 alternative clutch slave permitted. The
following STOPTECH parts are allowed with a 50 Lb penalty: #83.488.6800.51 front, 83.657.0057.51 rear.

2023-07-01 HP Correct Intake Valve Size on 1500cc Midget/Spitfire

#34419 from Production Committee · Rule change · TB 23-06 (2023-05 Fastrack)

Summary

wordingFP and HP Sprite, Midget, and Spitfire 1500 intake valve size corrected to 36.6/(1.44).

As printed in Fastrack

In FP Spec Lines, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change Intake Valve Size as follows:
"(I) 36.6~~5.3~~/(1.44)"
In FP Spec Lines, Triumph Spitfire Mk. IV & 1500, change Intake Valve Size as follows:
"(I) 36.6~~5.5~~/(1.440)"
In HP Spec Lines, Triumph Spitfire 1500, change Intake Valve Size as follows:
"(I) 36.6~~5.5~~/(1.440)"
In HP Spec Lines, Triumph Spitfire Mk. III & IV 1500, change Intake Valve Size as follows:
"(I) 36.6~~5.5~~/(1.440)"

2023-08-01 T2 Rules Clarification for Mazda RX8 Spec Line

#34395 from Colin Koehler · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

wordingT3 Mazda RX-8 removes transmission/final drive pairing requirement; T4 removes same requirement, adds Mazdaspeed radiator and coil spring kit.

As printed in Fastrack

In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows:
"~~Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3 transmission must be paired with the listed~~
~~alternate final drive.~~ Front sway bar permitted 32mm MAX rear sway bar 19 MAX, Front springs max 750, 500 rear. Cold air
intake permitted. Header permitted. Aftermarket flywheel and single disc clutch permitted with no weight penalty."
In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows:
"Mazdaspeed radiator #0000-01-8501 allowed. ~~Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3~~
~~transmission must be paired with the listed alternate final drive.~~ Mazdaspeed coil spring kit #QSEA-34-01Z allowed. 60mm flat
plate restrictor required. OE Rear spoiler allowed #F151-V4-920F. OE front air dam allowed #F151-V4-900f-BB. Springs Allowed:

Show 2 more lines

(F) Mazda Motorsports- 0000- 04-9700-08 or Eibach- 0800.250.0700 (R) Mazda Motorsports- 0000-04-9400-07 or Eibach
0700.250.0400, and helper 0000-04-9926 allowed. Alternate sway bars allowed max 32mm (f) 19mm (r)."

2023-08-01 T2 rule book corrections

#34437 from Chi Ho · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

fasterT3 BMW 320i (14-15) gains aftermarket intercooler permission; T4 loses it.

As printed in Fastrack

In T3 Spec Lines, BMW 320i (14-15), add to Notes the following:
"Aftermarket intercooler permitted."
In T4 Spec Lines, BMW 320i (14-15), remove from Notes the following:
"~~Aftermarket intercooler permitted.~~"

2023-08-01 T2 Corvette LS2 Restrictor Plate Adjustment

#34456 from Brian LaCroix · Rule change · TB 23-08 (2023-05 Fastrack)

Summary

fasterT2 Chevrolet Corvette C6 LS2 restrictor plate increases from 58mm to 60mm flat plate.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), change Notes as follows:
"LS2: ~~58mm~~ 60mm flat plate restrictor is required."

2023-08-01 T2 Ride Height Correction for the T3 Solstice.

#34615 from Joe Aquilante · Rule change · TB 23-08 (2023-08 Fastrack)

Summary

wordingT3 Pontiac Solstice GXP minimum ride height set to 3 inches.

As printed in Fastrack

In T2 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following:
"Minimum ride height is 3 inches."
In T3 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following:
"Minimum ride height is 3 inches."

2023-08-01 T2 Blacking Cadillac Fuel Capacity

#34624 from John Heinricy · Rule change · TB 23-08 (2023-05 Fastrack)

Summary

wordingT2 Cadillac CT4-V Blackwing permitted to use Radium fuel surge tank behind fireproof bulkhead.

As printed in Fastrack

In T2 Spec Lines, Cadillac CT4-V Blackwing (2022-), add to Notes the following:
"Radium fuel surge tank permitted. Radium tank and all associated hoses must be located behind a fireproof bulkhead or in the
engine compartment."

2023-09-01 HP Larger chokes

#34681 from Brian Downey · Rule change · TB 23-09 (2023-09 Fastrack)

Summary

fasterHP Nissan/Datsun PL510 carburetors allow larger 4mm chokes, replacing 2mm specification.

As printed in Fastrack

In HP Spec Line, Nissan/Datsun PL510, change Carburetor. No. & Type as follows:
"(1) 40 DCN, DCNF w/ 32 4mm choke(s), . or (1) 36mm DCNVH. (2) auto type side draft(s) w/ 32 4mm choke(s) on I.R. manifold @
90lbs penalty."

2023-12-01 HP Porsche 944/924S Rule Change Request

#35002 from Adam Achepohl · Rule change · TB 23-12 (2023-12 Fastrack)

Summary

cars addedEP Porsche 944/924S combines 2.5L and 2.7L variants with new weights: 2250–2415 lbs depending on engine and year.

As printed in Fastrack

In EP Spec Lines, delete the Porsche 944/924S 2.5L (2V) (83-88) spec line entirely, and create a new spec line for Porsche
944/924S 2.5L(2V) 2.7L(2V) (83-89) as follows:

A specification table follows in the original; it is not shown here.

2023-12-01 HP FP and HP Toyota Corolla

#35030 from Keith Church · Rule change · TB 23-12 (2023-12 Fastrack)

Summary

fasterFP Toyota Corolla 2TC loses 43 lbs to 1810; HP Corolla loses 50–52 lbs to 1910–2006.

As printed in Fastrack

In FP Spec Lines, Toyota Corolla 2TC (71-74), change weight as follows:
"~~1853~~ 1810"
In HP Spec Lines, Toyota Corolla (71-74), change weight as follows:
“~~1960~~ 1910
* ~~2009~~ 1958
** ~~2058~~ 2006”

2023-12-01 HP Weight Reduction for Mazda 626

#35031 from David Reiter · Rule change · TB 23-12 (2023-12 Fastrack)

Summary

fasterHP Mazda 626 84-87 weight reduced to 2200 lbs, 2255 lbs, and 2310 lbs across three configurations.

As printed in Fastrack

In HP Spec Lines, Mazda 626 (84-87), change weight as follows:
"~~2300~~ 2200
*~~2358~~ 2255
**~~2415~~ 2310"

2023-12-01 HP Triumph GT6 Adjustments

#35054 from ANTHONY PARKER · Rule change · TB 23-12 (2023-12 Fastrack)

Summary

fasterEP Triumph GT6 minimum weight reduced to 1800 lbs.

As printed in Fastrack

In EP Spec Lines, Triumph GT6, change weight as follows:
"~~1830~~ 1800"

2023-12-01 HP Request to Adjust Weight of 1988-1991 CRX/Civic

#35115 from Enrik Benazic · Rule change · TB 23-12 (2023-09 Fastrack)

Summary

fasterHP Honda CRX 1.5 (88-91) weight reduced to 2175 lbs, 2229 lbs, and 2284 lbs across three spec lines.

As printed in Fastrack

In HP Spec Lines, Honda CRX 1.5 (88-91), change weight as follows:
"~~2245~~ 2175
*~~2301~~ 2229
**~~2357~~ 2284"

2023-12-01 T2 M2 CS RACING

#35122 from Clark Giguiere · Rule change · TB 23-12 (2023-12 Fastrack)

Summary

aeroT2 BMW M2 CS Cup 2020- permitted to add hood vents conforming to 9.1.9.2.D.8.a.7.

As printed in Fastrack

In T2 Spec Lines, BMW M2 CS Cup 2020-, add to Notes the following:
"Hood vents conforming to 9.1.9.2.D.8.a.7 are permitted."

2024-01-01 HP Request to Review Z3 2.5 Spec Line

#35073 from Tim Schreyer · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

slowerEP BMW Z3 2.5L weight increases to 2500 lbs, 2563 lbs with turbo, 2625 lbs with supercharger.

As printed in Fastrack

In EP spec line, BMW Z3 2.5L, change weight as follows:
"~~2450~~ 2500
*~~2511~~ 2563
**~~2573~~ 2625"

2024-01-01 T2 Rebalance Blackwing Cadillac T2

#35079 from John Heinricy · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

fasterT2 Cadillac CT4-V Blackwing rear wheels widen from 18 x 10 to 18 x 11.

As printed in Fastrack

In T2 Spec Lines, Cadillac CT4-V Blackwing (2022-), change as follows:
Wheel size: "~~(F) 18 x 10 (R)~~ 18 x 11"
Notes: "Sway bars permitted 35mm (f), 30mm (r)"

2024-01-01 T2 M2 CS RACING

#35130 from Clark Giguiere · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

fasterT2 BMW M2 CS Cup drops 50 lbs to 3550; M235iR drops 50 lbs to 3300.

As printed in Fastrack

In T2 Spec Lines, BMW M2 CS Cup (2020-), change weight as follows:
"~~3600~~ 3550"
In T2 Spec Lines, BMW M235iR (-2016), change weight as follows:
"~~3350~~ 3300"

2024-01-01 HP Parity in HP

#35138 from Kendall Jones · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

fasterHP Sprite/Midget Mk I–IV, Mk 1500 compression ratio raised to 12.0:1 at Prep Level 1/2.

As printed in Fastrack

In HP Spec Line, Austin-Healey Sprite Mk I, II, III, IV / MG Midget Mk I, II, III, IV & 1500, Prep Level 1/2, change Notes section as
follows:
"Compression ratio limited to 11 12.0:1"

2024-01-01 T2 Spec Corvette in T2

#35139 from David Sanders · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

fasterT2 Spec Corvette minimum weight drops 175 lbs to 3200, tire rules tighten to Nankang NS-2R only.

As printed in Fastrack

In T2 Spec Lines, Spec Corvette, change as follows:
Weight: "~~3375~~ 3200"
Notes: "Cars must comply with all Spec Corvette rules dated ~~3-1-2~~ 1 11-28-22 including fuel and tires. No tire treatment or
rubber softeners are permitted. ~~T2 requirements of 3.75” min ride height and 53mm flat plate restrictor required. Any 295 DOT~~
~~tire approved with +200lb.~~ Limited to 380 HP. Nankang NS-2R Tires conforming to Spec Corvette rules are required."

2024-01-01 T2 T2 Viper BoP

#35155 from Scotty B White · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

slowerT2 Dodge Viper SRT-10 rear tyre narrowed from 345/30 to 335/30.

As printed in Fastrack

In T2 Spec Lines, Dodge Viper SRT-10 incl. coupe (03-06), change Tire Size as follows:
"(F) 315/35 (R) ~~345/30~~ 335/30"

2024-01-01 T2 BOP Adjustment for 5.0L Mustangs

#35156 from Kurt Rezzetano · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

slowerT2 Ford Mustang GT 5.0L three generations gain 50-75 lbs minimum weight; restrictors increase to 58-60mm.

As printed in Fastrack

In T2 Spec Lines, Ford Mustang GT 5.0L (11-14), change as follows:
Min weight: "~~3500~~ 3575"
Notes: "~~58mm~~ 60mm flat plate restrictor required."
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), change as follows:
Min Weight: "~~3600~~ 3650"
Notes: "~~58mm~~ 59mm flat plate restrictor required."
In T2 Spec Lines, Ford Mustang GT5.0L(2018-), change as follows:
Min Weight: "~~3600~~ 3650"

Show 1 more lines

Notes: "~~55mm~~ 58mm flat plate restrictor required."

Applies to Ford Mustang on this page: Scotty B White

2024-01-01 T2 Take at Look at T-2 BOP

#35161 from Joe Aquilante · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

fasterT2 Chevrolet Camaro 1LE minimum weight drops 50 lbs to 3500, restrictor opens to 58mm flat plate.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Camaro, 1LE (2016-), change as follows:
Min Weight: "~~3550~~ 3500"
Notes: "~~56mm~~ 58mm flat plate restrictor required."

2024-01-01 T2 C5 Corvette Spec Line Oversight

#35169 from Carl Fung · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

fasterT2 C5 Z06 removes restrictor note from weight; C5/C6 Corvettes increase restrictors to 59mm, 63mm LS2, 53mm LS3.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04), change as follows:
Min Weight: :3425 ~~w/56mm flat plate restrictor)~~"
Notes: "59mm flat plate restrictor required."
In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13) change Notes as follows:
"LS2: ~~60mm~~ 63mm flat plate restrictor is required. LS3: ~~50mm~~ 53mm flat plate restrictor is required."

Applies to Chevrolet Corvette on this page: Josh Carroll, David Holmes, Patrick Howe, Evan Gold, Greg Nester, Michael Cheney, Luis Martinez

2024-01-01 HP Spitfire classification

#35224 from Michael Walz · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

unclearHP Triumph Spitfire 1500 valve spec changes from 36.6/5.5/(1.44/0) to 36.6/(1.44).

As printed in Fastrack

In HP spec line, Triumph Spitfire 1500, make the following change to the Valves column:
"(I) 36.6~~5.5~~/(1.440)"

2024-01-01 T2 Requested Update of Model Years of 370Z

#35231 from Richard Kulach · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

wordingT3 Nissan 370Z model years expanded to include NISMO Edition through 2022.

As printed in Fastrack

In T3 Spec Lines, Nissan 370Z (09-16) / 370Z NISMO Edition (09-13), change model as follows:
"Nissan 370Z ~~(09-16) / 370Z NISMO Edition (09-13)~~ ,incl. Nismo (2009-2022)"

2024-01-01 HP Miata Alternate Head

#35253 from Don Tucker · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

fasterEP Mazda MX-5 1.8L 1990-97 minimum weight drops to 2150 lbs; 1994-97 variants to 2000, 2050, 2100 lbs respectively.

As printed in Fastrack

In EP Spec Lines, Mazda MX-5 /Miata 1.8L (90-97), change weight as follows:
"~~2200~~ 2150"
Mazda MX-5 /Miata (94-97)
"~~2035~~ 2000
*~~2086~~ 2050
**~~2137~~ 2100"

2024-01-01 HP Triumph GT6 Adjustments

#35255 from Anthony Parker · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

fasterEP Triumph GT6 dual 1.75" carbs weight drops to 1940 lbs; triple Weber 40 DCOE options consolidated.

As printed in Fastrack

In EP spec line, Triumph GT6, make the following change in the Notes section:
"Two (2) 1.75” auto-type carburetors @ 1970 40 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990
lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive. ~~Three (3) Weber 40mm DCOE w/28mm venturi on individual~~
~~runner manifold @ 2020 lb.~~"

2024-01-01 HP Honda S2000 throttle body

#35272 from Aaron Johnson · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

fasterEP Honda S2000 fuel injected throttle body inside diameter increases from 62mm to 64mm.

As printed in Fastrack

In EP spec line, Honda S2000, make the following changes to its spec line:
Fuel Injected Equipped Throttle Body Inside Diameter: "62 64"
Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .500”. An adaptor plate can be used to mount the 62mm throttle body
from '00-05 to the '06-09 intake manifold. The adaptor plate can be no more than 1.25" thick, and its bore must not exceed the
"Fuel Injected Equipped Throttle Body Inside Diameter" maximum spec of 64mm."

2024-01-01 HP Front Header/Nose Panel Alternate Material For 84-87 CRX

#35301 from Darryl Saylor · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

wordingHP Honda CRX/Si 84-87 front header/nose panel may use alternate material if appearance remains stock.

As printed in Fastrack

In HP Spec Lines, Honda CRX/Si (84-87), in Notes, make the following change:
"Compression ratio limited to 11.0:1, Valve lift limited to .390”. The front header/nose body panel can be replaced by a
replica which may be constructed of an alternate material provided its appearance remains stock."

2024-01-01 HP Correction within Triumph TR8 Spec Line

#35315 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

wordingEP Triumph TR8 dry sump allowance moved from carburetor line to notes section.

As printed in Fastrack

In EP spec line, Triumph TR8 (78-81), move the "Dry sump allowed" wording to the appropriate location as follows:
Carburetor. No. & Type: “Zenith Stromberg carbs or fuel injection. ~~Dry sump is allowed.~~”
Notes: “Comp. Ratio limited to 12.0:1, Valve lift limited to .500”. Dry sump is allowed.”

2024-01-01 HP Correction to EP 924S/944 Spec Line

#35317 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

wordingEP Porsche 944/924S 2.5L and 2.7L weight minimums corrected: 2479cc to 2306/2363 lbs, 2681cc to 2358/2415 lbs.

As printed in Fastrack

In EP spec line, Porsche 944/924S 2.5L (2V) / 2.7L (2V) (83-89), change Weight as follows:

A specification table follows in the original; it is not shown here.

2024-01-01 HP Review Classification of HP Mazda 2

#35318 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)

Summary

slowerHP Mazda 2 (11-14) minimum weight increases to 1995 lbs, 2045 lbs with*, 2095 lbs with**.

As printed in Fastrack

In HP spec line, Mazda 2 (11-14), make the following weight changes:
"~~1920~~ 1995
*~~1968~~ 2045
**~~2016~~ 2095"

2024-02-01 T2 2015+ Mustang Sway Bar and A-Arm Request

#35154 from Scotty B White · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

suspension & brakesT2 Mustang GT 5.0L 15-17 now permits BMR rear upper control arm camber links part #UTCA064.

As printed in Fastrack

In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes the following:
"BMR rear upper control arm camber links part #UTCA064 permitted."

Applies to Ford Mustang on this page: Scotty B White

2024-02-01 T2 Brake Kits

#35245 from David Woodle · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

otherT2 Chevrolet Camaro SS, 1LE, Corvette C5/C6, Z06, and Pontiac Firebird, Solstice GXP now allow four or six piston front calipers.

As printed in Fastrack

In T2 Spec Lines, add to Notes the following:
Chevrolet Camaro SS (98-02): “Four or six piston front calipers allowed.”
Chevrolet Camaro, 1LE (2016-): “Four or six piston front calipers allowed.”
Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04): “Four or six piston front calipers allowed.”
Chevrolet Corvette C6 Coupe / Grand Sport (05-13): “Four or six piston front calipers allowed.”
Chevrolet Corvette Z06 (06-12): “Four or six piston front calipers allowed.”
Pontiac Firebird (98-02): “Four or six piston front calipers allowed.”
Pontiac Solstice GXP Coupe/Convertible (07-09): “Four or six piston front calipers allowed.”

2024-02-01 T2 More Car Lightening Stuff

#35319 from Scotty B White · Rule change · TB 24-02 (2024-02 Fastrack)

Summary

fasterT2, T3, T4 battery replacement wording simplified; OEM weight tolerance requirement removed.

As printed in Fastrack

In GCR, Section 9.1.9.2.D.1.g.3., change as follows:
"Batteries may be replaced provided the replacement is capable of starting the car. Batteries may not be relocated
unless noted on the spec line. Batteries must be adequately secured. Battery labeling must conform to 9.3.35.D. ~~with~~
~~those of an alternate manufacturer, provided they are of similar amp-hour capacity, size and within 10% of OEM~~
~~weight.~~"

2024-02-01 T2 Inclusion of B-C spec cars in T4

#35374 from Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)

Summary

cars addedT4 now permits C-Spec cars to compete alongside B-Spec cars.

As printed in Fastrack

In GCR, Section 9.1.9.2., change as follows:
"Touring car eligibility: Cars are eligible for the class they are listed with a specification line and with the specific
allowances permitted. In addition, T2-T4 cars may race one class up in touring classes above their specification line class
as long as they are a legal T2-T4 car and conform to their specification line allowances as classified. Cars conforming to
C-Spec rules are permitted to compete in Touring 4."

2024-02-01 T2 Runoffs wording on Caddy in T2

#35377 from Touring Committee · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

wordingT2 Cadillac CT4-V Blackwing Runoffs qualification requirement removed.

As printed in Fastrack

In T2 Spec Lines, Cadillac CT4-V Blackwing(2022-), change Notes as follows:
"~~THIS CAR DOES NOT QUALIFY FOR SCCA RUNOFFS COMPETITION UNTIL IT HAS BEENREPRESENTED IN 3 SCCA SUPER~~
~~TOUR EVENTS~~."

2024-02-01 T2 T2-T4 Set expiration dates on spec lines

#35378 from Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)

Summary

wordingT2-T4 spec lines for 46 cars expire 12/31/24; appeal required to continue.

As printed in Fastrack

In T2-T4 Spec Lines, add **This Spec line will expire 12/31/24, Please submit to appeal**
to Notes to the following Spec Lines:
T2:
Acura TL SHAWD (10-13)
Audi S4 (12-14)
Audi S5 (13-14)
Audi TT RS (2018-)
Cadillac ATS-V (16-17)

Show 46 more lines

Cadillac CTS-V (06-07)
Chevrolet Camaro SS (98-02)
Honda Civic (2017-)
Saturn Sky / Convertible (07-09)
Subaru Impreza WRX STi (03-07)
Subaru Impreza WRX STi (08-11)
T3:
Audi S4 (10-11)
Audi S4 (12-14)
Audi TTS Coupe (10-11)
Cadillac ATS (2015)
Chevrolet Cobalt (05-07)
Dodge SRT-4 (03-05)
Ford Fiesta ST (2014-)
Hyundai Genesis Coupe (2010-)
Hyundai Veloster Turbo (18-21)
Mazda RX-8 Base/R3/Sport/ GT (04-12)
Mini Cooper S (2016-)
Subaru WRX (02-05)
Toyota Camry (11-15)
T4:
Acura Integra GS-R VTEC (3 or 4 door) (94-01)
Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05)
BMW 320i (14-15)
Chevrolet Cobalt SS, Sport Coupe (06-10)
Chevrolet Sonic RS (2011-)
Chrysler/Dodge Neon ACR SOHC (4 door) (01-02)
Dodge Dart (14-15)
Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99)
Fiat 500 Abarth (12-14)
Ford Focus SVT (02-04)
Ford Focus ZX4 ST (05-06)
Ford Focus (08-11)
Ford Mustang V-6 (01-04)
Honda Accord LX & EX (03-07)
Honda Accord LX-S/EX/EX-L (08-12)
Honda Civic Coupe Si (99-00)
Honda Civic SI (02-03)
Hyundai Elantra GLS (11-12)
Hyundai Tiburon V-6 (03-08)
Hyundai Veloster Turbo/ R-Spec (14-15)
Kia Forte Koup and Sedan LX/EX (10-13)
Kia Forte Koup and Sedan SX (10-13)
Kia Forte Koup (14-15)
Mazda Protégé ES (2000)
Mazda Protégé 5 (02-03)

2024-02-01 T2 Reply to letter #35161 and #31661

#35384 from Andrew Aquilante · Rule change · TB 24-02 (2024-02 Fastrack)

Summary

slowerT2 Chevrolet Camaro 1LE minimum weight increases to 3575 lbs, restrictor plate widens to 60mm.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Camaro, 1LE (2016-), change as follows:
Min Weight: "~~3500~~ 3575"
Notes: "~~58mm~~ 60mm flat plate restrictor required"

2024-02-01 HP Update 1988-1991 Civic to Match 1988-1991 CRX

#35399 from Enrik Benazic · Rule change · TB 24-02 (2024-01 Fastrack)

Summary

fasterHP Honda Civic 1.5 (88-91) weight reduced to 2175 lbs base, 2229 lbs with power adder, 2284 lbs with two.

As printed in Fastrack

In HP, make the following weight change:
Honda Civic 1.5 (88-91)
~~“2245~~ 2175
*~~2301~~ 2229
**~~2357~~ 2284”

Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22

2024-03-01 T2 Reorganize Spec Lines

#35375 from Touring Committee · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

unclearT2-T4 Spec Lines remove wheelbase requirement, replace with Required Restrictor specification.

As printed in Fastrack

In T2-T4 Spec Lines, change Spec Line as follows:
"~~Wheel- base (mm)~~ Required Restrictor"

2024-03-01 T2 370Z Brake Rotor Size Correction

#35487 from Derek Chan · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

suspension & brakesT2 and T3 Nissan 370Z brake rotors enlarged: front 320x28 to 355x32mm, rear 320x16 to 350x20mm vented.

As printed in Fastrack

In T2 Spec Lines, Nissan 370Z (09-17) / 370Z NISMO Edition (09-17), change Brakes (mm) as follows:
"~~(F)320 x 28 Vented R)320 x 16 Vented :~~ (F) 355x32mm Vented(R) 350x20mm Vented”
In T3 Spec Lines, Nissan 370Z, incl. Nismo (2009-2022), change Brakes (mm) as follows:
"~~(F)320 x 28 Vented (R)320 x 16 Vented :~~ (F) 355x32mm Vented(R) 350x20mm Vented”

2024-03-01 T2 Letter #35154 2018+ Mustang GT Expansion

#35488 from Michael Kamalian · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

suspension & brakesT2 Mustang GT 5.0L 2018+ now permits BMR rear upper control arm camber links part #UTCA064.

As printed in Fastrack

In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows:
"BMR rear upper control arm camber links part #UTCA064 permitted."

Applies to Ford Mustang on this page: Scotty B White

2024-03-01 HP GCR Correction - Redundant HP Spec Lines

#35623 from Production Committee · Rule change · TB 24-03 (2024-03 Fastrack)

Summary

wordingHP removes four redundant VW spec lines: Rabbit Cabriolet 1780, Scirocco 1588, Scirocco 1780 8-valve, Scirocco 1588.

As printed in Fastrack

In HP Spec Lines, delete the following redundant spec lines in their entirety:
Spec line #10 - VW Rabbit Cabriolet 1780
Spec line #3 - VW Scirocco 1588
Spec line #4 - VW Scirocco 1780 (8-valve) (83-88)
Spec line #5 - VW Scirocco 1588

2024-04-01 T2 Brake Request for 2009 Porsche Cayman

#35723 from Jason Ott · Rule change · TB 24-04 (2024-04 Fastrack)

Summary

slowerT2 Porsche Cayman S 06-09 allows StopTech ST60/ST40 brake kit with 50 lb penalty.

As printed in Fastrack

In T2 Spec Lines, Porsche Cayman S (06-09), add to Notes the following:
"The following brake kit is allowed in its entirety with a 50 lb penalty- (f) StopTech ST60 (83.788.6700), rotor size 355X32
(r) StopTech ST40 (83.799.0046), rotor size 332X32."

2024-05-01 T2 Allow T4 and T3 RX8 to Disable/Remove Factory Oil Inj.

#35761 from David Mead · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

unclearT3 and T4 Mazda RX-8 may remove or disable factory oil injection system.

As printed in Fastrack

In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows:
"OEM oil injection system may be removed or disabled."
In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows:
"OEM oil injection system may be removed or disabled."

2024-05-01 HP Replace plastic panels

#35875 from Darryl Saylor · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

wordingHP Honda CRX/Si 84-87 plastic panels can be replaced with replica alternate material if stock appearance maintained.

As printed in Fastrack

In HP spec line "Honda CRX/Si (84-87)", make the following change to the Notes section:
"The plastic OE front header/nose body panel, lower rocker side-skirt, and lower door cap panel can be replaced by a
replica, which may be constructed of an alternate material, provided its appearance remains stock."

2024-05-01 T2 Competition Adjustment Request/Wheel Size of E46

#35895 from David Newman · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

fasterT2 BMW M3 01-06 max wheel size increases from 18 x 9 to 18 x 10 inch.

As printed in Fastrack

In T2 Spec Lines, BMW M3 (01-06), change Max Wheel Size (inch) as follows:
"~~18 x 9~~ 18 x 10"

2024-05-01 T2 Driveshafts

#35916 from Scotty B White · Rule change · TB 24-05 (2024-05 Fastrack)

Summary

slowerT2, T3, T4 driveshafts may use alternative materials or one-piece units; non-OEM adds 25 lbs.

As printed in Fastrack

In GCR Section 9.1.9.2.D.4.b., add the following:
"6. T2-T3- Driveshafts may be replaced with alternative materials ie. carbon fiber, aluminum, steel. Two-piece driveshafts may
be replaced with one-piece units. If non-OEM driveshaft is used, add 25 lbs."

2024-06-01 HP NIssan 300ZX Z31 to EP

#35830 from Murphy Nichols · Rule change · TB 24-06 (2024-06 Fastrack)

Summary

cars addedNissan 300ZX 84-89 classified to EP at 2550 lbs minimum, 2960cc 6-cyl SOHC, fuel injection, 12.0:1 compression limit, 0.500" valve lift limit.

As printed in Fastrack

In EP Spec Lines, classify Nissan 300ZX (84-89), as follows:

A specification table follows in the original; it is not shown here.

2024-06-01 HP RX7 1993 and Up Request In EP Spec Lines, classify

#36031 from Edward Zabinski · Rule change · TB 24-06 (2024-06 Fastrack)

Summary

cars addedMazda RX-7 92-97 newly classified EP Prep Level 2 at 2200–2310 lbs with 13B 6-port rotary engine.

As printed in Fastrack

Mazda RX-7 (92-97) as follows:

A specification table follows in the original; it is not shown here.

2024-06-01 HP Clean-up Multiple EP RX-8 Spec Lines In EP

#36156 from Production Committee · Rule change · TB 24-06 (2024-06 Fastrack)

Summary

wordingEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.

As printed in Fastrack

Spec Lines, make the following changes to the two Mazda RX-8 spec lines.
Remove spec line entirely:
~~Mazda RX-8 (04-11)~~
Remove the wording "alternate":
Mazda RX-8 (04-11)~~(alternate)~~
Spec Mazda (SM/SMX) None.

2024-07-01 T2 Mustang T2/T3

#35877 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)

Summary

unclearFord Mustang GT 5.0L and V6 now permit Track/Performance Package parts in T2 and T3.

As printed in Fastrack

In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes as follows:
"Track/Performance Package parts permitted."
In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows:
"Track/Performance Package parts permitted."
In T3 Spec Lines, Ford Mustang V6 (15-17), change Notes as follows:
"Track/Performance package allowed."

Applies to Ford Mustang on this page: Scotty B White

2024-07-01 T2 S550 Brakes

#35926 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)

Summary

slowerT2 Ford Mustang S550 5.0 Gen2/Gen3 gains 100 lbs with stock or Brembo 355mm brakes.

As printed in Fastrack

In T2 Spec Lines, Ford Mustang Ecoboost 2.3 (2015-), add to Notes the following:
"100LB for Mustang S550 2015-17 5.0 Gen2 and 2018-23 5.0. Gen3 reduce weight by 100Lb when using 4 piston stock
or Brembo brakes with 355mm rotors."

2024-07-01 T2 T2-T4 Driveshaft Mistake...?

#36050 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)

Summary

fasterT2-T4 Ford Mustangs: remove 25 lbs penalty for non-OEM driveshaft, clarify alternate driveshaft allowances.

As printed in Fastrack

In GCR Section 9.1.9.2.D.4.b.6., remove as follows:
"~~If non-OEM driveshaft is used, add 25 lbs.~~"
In T2 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows:
"~~Driveshaft from~~ Alternate ~~metallic~~ driveshaft is allowed."
In T2 Spec Lines, Ford Mustang Boss 302 (12-13), change Notes as follows:
"Alternate ~~metallic~~ driveshaft is allowed."
In T2 Spec Lines, Ford Mustang GT 5.0L (11-14)ki, change Notes as follows:
"Alternate ~~metallic~~ driveshaft is allowed."

Show 12 more lines

In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), change Notes as follows:
"Alternate ~~metallic~~ driveshaft is allowed."
In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), change Notes as follows:
"Alternate ~~metallic~~ driveshaft is allowed."
In T2 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L (05-10), change Notes as follows:
'~~An Aluminum driveshaft is allowed.~~"
"~~Alternate metallic driveshaft is allowed.~~"
In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), change Notes as follows:
"~~An Aluminum driveshaft is allowed.~~"
"~~Alternate metallic driveshaft is allowed.~~"
In T3 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows:
"~~Driveshaft from Alternate metallic driveshaft is allowed.~~"

Applies to Ford Mustang on this page: Scotty B White

2024-07-01 T2 request for allowance of 6 piston calipers for T2 C5 corvettes

#36126 from Joe Aquilante · Rule change · TB 24-07 (2024-07 Fastrack)

Summary

fasterT2 Corvette C5, Camaro SS, Firebird, Solstice GXP, C6 allow four or six piston front calipers.

As printed in Fastrack

In T2 Spec Lines, add to Notes the following:
Chevrolet Camaro SS (98-02): Four or six piston front calipers allowed.
Chevrolet Camaro, 1LE (2016-): Four or six piston front calipers allowed.
Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04): Four or six piston front calipers allowed.
Chevrolet Corvette C6 Coupe / Grand Sport (05-13): Four or six piston front calipers allowed.
Chevrolet Corvette Z06 (06-12): Four or six piston front calipers allowed.
Pontiac Firebird (98-02): Four or six piston front calipers allowed.
Pontiac Solstice GXP Coupe/Convertible (07-09): Four or six piston front calipers allowed.

2024-07-01 T2 B8/8.5 Audi S4 T3 and T2

#36195 from Brian Leib · Rule change · TB 24-07 (2024-07 Fastrack)

Summary

cars addedAudi S4 (2000-2002) moves to T3 with 3400 lbs minimum weight, 38mm turbo inlet restrictor required.

As printed in Fastrack

In T3 Spec Lines, Classify Audi S4 (2000-2002) as follows and allow the T2 spec line to expire.

A specification table follows in the original; it is not shown here.

2024-08-01 T2 Errors

#36214 from Touring Committee · Rule change · TB 24-08 (2024-08 Fastrack)

Summary

unclearT2 Corvette C6 LS2 restrictor increases to 63mm; Camaro 1LE weight drops to 3500 lbs, restrictor tightens to 58mm FRP.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), change Required Restrictor as follows:
"LS2: "53 63mm flat plate restrictor"
In T2 Spec Lines, Chevrolet Camaro, 1LE (2016-), change as follows:
Min Weight: "~~3575~~ 3500"
Required Restrictor: "~~60mm FRP~~ 58mm flat plate restrictor"

2024-08-01 HP Errant entry in HP production line item

#36231 from Angus Crome · Rule change · TB 24-08 (2024-08 Fastrack)

Summary

wordingHP Volkswagen Golf and Jetta 85-92 track correction: front 1537mm (60.5in), rear 1529mm (60.2in).

As printed in Fastrack

In HP Spec Lines, change Track (F/R)mm/(in.) as follows:
Volkswagen Golf (GTI, GT, GL) (85-92): "2 1537/1529 (60.5/60.2)"
Volkswagen Jetta (GLI, GL) (85-92): "2 1537/1529 (60.5/60.2)"

2024-08-01 T2 Subaru Appeal

#36258 from Anthony Piselli III · Rule change · TB 24-08 (2024-08 Fastrack)

Summary

wordingT2 Subaru Impreza WRX STi (03-07) and (08-11) expiration notes removed.

As printed in Fastrack

In T2 Spec Lines, Subaru Impreza WRX STi (03-07), change Notes as follows:
"~~**This Spec line will expire 12/31/24, Please submit to appeal**~~"
In T2 Spec Lines, Subaru Impreza WRX STi (08-11), change Notes as follows:
"~~**This Spec line will expire 12/31/24, Please submit to appeal**~~"

2024-08-01 T2 S550 Brakes

#36571 from Club Racing Board · Rule change · TB 24-08 (2024-08 Fastrack)

Summary

fasterT2 Ford Mustang 5.0L gets 100 lb weight reduction with 4-piston Brembo brakes and 355mm rotors; EcoBoost brake note removed.

As printed in Fastrack

In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes as follows:
"Mustang S550 2015-17 5.0 Gen2 and 2018-23 5.0. Gen3 reduce weight by 100Lb when using 4 piston stock or Brembo brakes
with 355mm rotors."
In T2 Spec Lines, Ford Mustang GT 5.0L (18 -), add to Notes as follows:
"Mustang S550 2015-17 5.0 Gen2 and 2018-23 5.0. Gen3 reduce weight by 100Lb when using 4 piston stock or Brembo brakes
with 355mm rotors."
In T2 Spec Lines, Ford Mustang Ecoboost 2.3 (2015-), change Notes as follows:
"~~Reduce weight by 100Lb when using either stock 355mm 4 piston brakes or m2300s 355mm 4 piston Ford brake kit.~~"

Applies to Ford Mustang on this page: Scotty B White

2024-09-01 SMX SMX Camera Rule Correction

#36496 from Paul Gauzens · Rule change · TB 24-09 (2024-09 Fastrack)

Summary

wordingSMX Spec MX-5 camera requirement wording changed; non-functioning recorder now grounds for penalty or disqualification.

As printed in Fastrack

In GCR, Section 9.1.7.1.D.21., change as follows:
"Cars running in Spec MX-5 must have a functioning video recorder/camera during all qualifying and race sessions as described
in 9.3.11. Upon request by an SCCA official, competitors must provide their video recording/data, which may be used by the
SCCA for any purpose including but not limited to rule enforcement and marketing. Failure to comply with a video request from
an official, or having a non-functioning video recorder/camera ~~may~~ will be grounds for penalty or disqualification."

2024-09-01 SMX Committee) AIM ECU Protocol

#36556 from Spec Mazda (SM/SMX · Rule change · TB 24-09 (2024-09 Fastrack)

Summary

wordingSMX Spec MX-5 must run latest AIM Data Logger Spec MX-5 ECU Protocol; wording clarification for technical compliance.

As printed in Fastrack

In GCR, Section 9.1.7.1.D.20., add the following:
“e. All cars must run the latest AIM Data Logger Spec MX-5 ECU Protocol.”
These specifications are part of the SCCA GCR and all automobiles shall conform to GCR Section 9.
A. PURPOSE AND
INTENT
Spec MX-5 (SMX) is based on four pillars: affordability, reliability, tech-ability, and fun to drive, the (SMX) Spec MX-5 car
provides the membership with the opportunity to compete in similarly prepared, low cost, 2006-2015 production-based MX-
5 car with limited modifications, intended to help deliver the most fair and competitive racing competition in SCCA Road

Show 660 more lines

Racing
B. CLASSIFIED CARS
AND WEIGHTS
2006-2015 production-based MX-5
Cars are to be weighed with the driver and required ballast.
C. AUTHORIZED
MODIFICATIONS
Only the left-hand drive, North American-version of the 2006-2015 Mazda MX-5 convertible & power retractable hardtop
(PRHT) are eligible. The original OE vehicle identification number (VIN) stamped on the firewall must correspond with the
model year automobile as classified. VIN plates or stampings must remain in place, with the firewall VIN taking precedence.
A Mazda Factory Shop Manual for the specific make, model, and year of automobile is required to be in the possession
of each entrant. The manual may be in the form of printed material, microfiche, CDs, DVDs, and/ or Internet access to
manufacturer sponsored web-based databases that is readily accessible at time of inspection. The manual is intended to
aid scrutineers in identifying parts and the configuration of the automobile.
The items outlined in this VTS document represent the only modifications and safety items permitted and/or required on
Spec MX-5 vehicles other than safety items as required in SCCA’s current GCR Section
9. Parts and components may not perform an unauthorized function (i.e. Modifications must be stated as authorized or
cannot be done).
If the Mazda Factory Manual or these rules provide only a partial specification or no specification at all, the Mazda parts may
not be modified beyond what is permitted in these rules. Compliance will be determined by comparison to new or like parts
and/or the parts compliance measurement listing delivered by Mazda. Other approved parts with only a partial specification
or no specification available in these rules may not be modified.
Assembly, rebuild, and refurbishment procedures, and all associated dimensions must adhere to the published factory
service procedures, except as otherwise stated in these rules. No components may be added or omitted from those
specified by the published factory service procedures. All components must be comply with stated standard dimensions.
It is permitted to use industry standard procedures to repair damaged components.
The use of any painting, coating, plating, metal treatment process or impregnating substance (e.g., anti- friction, thermal
barrier, oil shedding coatings, chrome, anodizing, REM, isotropic finishing, etc.) to any internal engine surface, internal
axle components, internal transmission or differential surface, internal or external surfaces of the intake manifold, exhaust
manifold or down tube, is prohibited.
D. VEHICLE
TECHNICAL
SPECIFICATIONS
(VTS)
1. Vehicle Weight
a. The minimum vehicle weight with driver is 2,525.0 lb.
2. Ballast
If ballast is required to meet the required minimum weight, it must be added as follows:
a. A ballast base plate must be securely mounted using the factory OE passenger seat mounting bolt holes and bolts. Any number
of additional segments of ballast may be attached to the base plate.
b. Each segment of ballast must be fastened to the base plate with a minimum of two (2) one-half (1/2) inch bolts/studs and
positive lock nuts of SAE Grade 5/ Metric 8.8 or better and must utilize large diameter, load distributing washers. In lieu of
positive lock nuts it is permitted to positively thread the additional segments of weight into the base plate.
c. Holes are not permitted to be drilled in the floor pan to mount ballast.
3. Chassis
a. Towing eyes per SCCA’s current GCR Section 9.3 are required. There must be an arrow that strongly contrasts with the vehicle
paint scheme pointing to each tow eyestrap.
9.1.7.1 SPEC MX-5 (SMX)
b. All cars must use the front subframe PT# - NE51-34-800C
c. All cars must use the rear subframe PT# - NE51-28-800B.
d. OE strut tower brace is required; it is comprised of three (3) components; see Table 1 for part numbers.
e. An engine to fender brace located on the passenger side of the engine bay may be used if mounted in such a way that it does not foul brake
lines, fuel lines, or other systems that would interfere with the safe operation of the vehicle under race conditions – see Table 1 for allowed
modifications. (Mazda Motorsports PT# 0000-07-5600)
f. Disabling or removing of the door locking mechanism must be performed.
g. To facilitate frequent lifting of the vehicle, a 3/4” boxed tube not to exceed 12” long may be added under the rocker panel inboard of
the factory pinch weld flange on each side of the vehicle.
h. Convertible tops/power retractable hard tops (PRHT) and attaching hardware must be completely removed.
i. All chassis, structural, and electrical repairs, if performed, must be in conformity with factory procedures, specifications, and dimensions.
Unless specifically authorized by the manufacturer for repair or permitted by these rules, no reinforcement (e.g., seam welding, material
addition, etc.) is permitted.
j. Removal of excess wiring is permitted provided it serves no other purpose and does not splice or interrupt the OE harnesses. Removal of the
following systems is permitted: audio equip- ment; power seats; airbag/supplemental restraint systems components; heated seats; interior
lighting; power windows; and power door locks. (No additional wiring may be added except as permitted in other sections - e.g., Section 16:
Electrical Equipment.)
Table 1: Strut Tower Brace Parts
Description Mazda Part #
Right Side of Strut Tower
Brace
NE57-56-48X
Left Side of Strut Tower
Brace
NE57-56-49X
Center Section of Strut
Tower Brace
NE57-56-48ZA
k. A hole is permitted to be drilled in part #’s NE57-56-48X and NE57-56-49X to allow for access to the shock adjuster screw is permitted (it is
recommended that the hole not be larger than 15mm); NE57-56-48X may be modified in order to allow room for the engine passenger side
engine brace; no other modifications or other braces are permitted.
l. MX-5 donor chassis with originally equipped with 16” OE wheels require installation of
OE strut tower brace (part # NE57-56-35XA).
m. To facilitate engine bay air flow for cooling purposes it is permitted to remove the section outlined below in red from OE PT# NE57-56-
35XA. Block-off plates must be installed at the fresh air vent for the HVAC module at the firewall under the cowl to isolate driver
compart- ment from engine compartment.
(FIREWALL BLOCKOFF PLATE 0000-07-5832) No additional modifications are permitted.
4. Body
a. Interior and exterior door handles are required to remain operable. Alternate interior door handles or cord/strap are permitted.
b. The driver’s and passenger’s side inner door structural panel may be removed to fit the cage.
c. The stock side impact/anti-intrusion beam must not be modified or removed.
d. Door locking mechanisms must be disabled or removed.
e. A minimum of two (2) of the brake lights must be in working order per the current GCR Section 9.1.
f. The two (2) OE unmodified, external mirrors for the correct the Mazda MX-5 (left and right) are required; they must be
mounted in stock location and may not be modified.
g. OE interior rearview mirror or an aftermarket rearview mirror must be used.
h. 2006-2015 MX-5 bodywork may be updated or backdated, OE body parts only. (This includes Mazda OE accessory body
parts such as trunk lid spoiler, side skirts, front air dam.)
i. Mazda Motorsports’ fiberglass headlamp replacements may be used; (See table 2)
no modifications or substitutions are permitted; exceptions: painting, covering, and wrapping.
Table 2: Headlamp Replacement Covers
Model Year Mazda Part # Description
2006-2008 0000-07-5818-LT Left Side
2006-2008 0000-07-5818-RT Right Side
2009-2015 0000-07-5819-LT Left Side
2009-2015 0000-07-5819-RT Right Side
j. Lexan windshield may be used in place of the stock windshield. (Mazda Motorsports PT# -
0000-07-5101-5S)
k. Windshield clips per current GCR Section 9.3 windshield clips are recommended.
l. Hood and trunk pins or clips are permitted. Factory hood and trunk latches must remain intact and operational and may not be
removed, disabled or altered.
m. Front under hood weather strip must remain intact PT#- NE51-56-750
n. Rear under hood weather strip must remain intact PT#- NE51-56-760
o. Modification of release cables is permitted to facilitate external pull/opening straps/pulls/cords.
p. A radiator screen of 0.125” minimum stainless-steel mesh may be added in front of the radiator.
1. The screen must be a single layer and must be installed to the bumper cover and or grill and be contained entirely within the
bodywork of the vehicle.
2. Tape may be applied to the mesh screen.
3. The OE grill must remain intact.
q. It is allowed to apply roll bar padding to the crash support bar (52-070) located behind the front bumper to prevent damage to the
bumper.
r. Front and rear fender lips may be rolled to prevent tire damage.
s. Front OE fender liners must be intact and unmodified, except for what is allowed in section 13. J regarding brake ducts.
Repairs due to on-track damage is allowed so long as it serves no other purpose.
t. OE fog lights lens/glass must be removed. This will allow for the installation of brake duct kit (Mazda Motorsports’ part # 0000-03-
5301-NC.) The remaining opening from the fog light lens must either be blocked, or a connection must be made from the fog lamp
opening/hole in the bumper fascia to a brake duct attached to the hub.
u. Side marker lenses may be removed, and holes may be covered.
v. OE hard top or the unmodified Mazda Motorsports hard top (part # 0000-07-5901-CC)
are permitted.
w. PRHT chassis cars must trim the finish panel with the 3rd brake light to fit one of the approved hard tops.
1. Hhardtops may be painted or wrapped.
2. OE hard top latches must be removed and replaced with positive fasteners.
3. The front of the hard top may attach to the upper windshield bar of the roll cage.
4. It is permitted to run one single piece of racer tape to cover the leading edge of the after- market hard top where it meets
the factory windshield frame.
5. Openings beneath the hard top seal to the body are not permitted. The hard top must be securely mounted to the body of the vehicle
and perform no other purpose.
6. Body repair must be performed to maintain stock body contours, lips, profiles, etc. body repair modification must not increase clearance.
x. To improve driver’s exit through the window area, the driver and passenger vent window and vent window supporting frame may be removed
as an assembly.
1. Vent windows may be modified to accept fresh air ducting.
y. OE radio antennas may be removed. Antennas for two-way radios may be added.
z. Insulation & undercoating may be removed.
aa. All cars must run with both the front door windows fully open (i.e. fully down).
5. Cockpit /
Trunk
a. All interior trim components such as carpets, seats, cargo bins, seat belts, floor mat, firewall insu- lation/blanket, sound deadener patches,
undercoating, radio systems, speakers, dome lights, grab handles, sun visors and their insulating and attaching materials, must be removed.
Other than to provide for the installation of required safety equipment or other authorized modifications, no other driver/passenger
compartment alterations or gutting are permitted.
b. It is permitted to install a radio replacement panel.
c. The outer edges of the dashboard may be cut the minimum amount required to install the roll cage.
d. Air bag systems must be disarmed and must be removed.
e. It is permitted to remove all components of the cruise control system.
f. The top portion of the door panels containing the door latch release handle must remain intact.
g. The lower portion of the door panels must be removed for installation of the roll cage. Gutting of the door may not go outside of the factory
seal.
h. The door window glass and window operating mechanisms must be removed.
i. The OE dashboard and its attaching hardware and brackets must be retained.
j. For installation of required safety equipment, however, it is permitted to modify the OE dash bar, so long as it is outboard of the first dash support
brackets (illustration below). Modification of the first dash support brackets, nor inboard from them, is not permitted. The OE dash bar must be
securely mounted.
k. The HVAC control module located under the dash may be removed together with the following: blower motor, evaporator core,
heater core and associated ducting. Once removed it is permitted to block the blower inlet passage on the firewall.
l. All openings between the driver/passenger compartment and the trunk / gas tank area that include the filler tube & fuel tank vent
must be filled completely with a metal bulkhead that is securely mounted (E.G. nuts/bolts, nut-serts, rivets). This shall close the
entire trunk from the driver/ passenger compartment and comply with current GCR Section 9.3.
m. Mazda Motorsports’ finish panel trim kit (part # 0000-07-5822) may be used to create the required bulkhead above
n. It is permitted to remove the driver’s side factory seat mounts, but not the floor pan.
o. It is permitted to remove the horn and all associated horn related components.
p. OE driver’s seat must be replaced with a one-piece bucket-type race seat per current GCR Section 9.3.
q. The passenger seat must be removed.
r. Any steering wheel except wood rimmed types may be used.
s. Any shift knob may be used.
t. The air conditioning equipment located in the engine compartment (AC compressor assembly, associated lines/dryer and the
condenser) must be removed.
u. Alternate gauges and instruments may be added. The original instrument cluster must remain connected and functional However,
it may be relocated to allow the mounting of an aftermarket dash such as an AiM. The wiring to relocate the dash may not be cut or
extended, it may only be re-routed. The remainder of the dashboard or panel must remain intact.
v. Modifications may be made to the foot pedals to improve the comfort and accessibility to the driver; relocation of mounting
points is not permitted.
1. Dead pedal/footrest and heel stop may be added.
w. Instrument clusters must be unmodified OE parts .
x. Two-way radios may be used.
y. Alternate means of windshield defrosting is permitted
6. Engine
Modifications
6.1. General
a. No modifications to the engine are permitted, except where specifically authorized within these rules. This includes but is not
limited to: all fuel injection and engine management components, as well as electrical, cooling, and lubrication systems.
b. All systems, unless otherwise stated, are subject to test procedures and must conform to OE
specifications as stated in the Mazda Factory Service Manual.
c. Permitted engine maintenance includes the replacement, but not modification, of external engine and engine systems parts.
1. No balancing, blue printing, lightening, polishing or other modification of moving parts of the engine is permitted.
2. All parts in the engine must be OE parts unless specified in this rule set.
3. For all Mazda part numbers in these specifications, superseding part numbers are consid- ered equivalent.
d. Compression ratio for 2.0L engines must be 11.00:1; calculated using the official Spec MX-5 calculator.
6.2. Engine Block
a. The engine block may be decked or milled to achieve the class specified compression ratio. Honing of cylinders is permitted to accommodate
piston clearance so long as a maximum standard diameter is not exceeded shown in Table 3.
b. The cylinders may be bored to accommodate piston clearance requirements so long as maximum permitted overbore diameter is not exceeded
shown in Table 3 below.
Table 3: Piston Sizes
Piston Part # Bore Diameter Max
Standard 0000-01-5310 87.6046mm (3.449”)
Allowed Overbore (.020) 0000-01-5310-OS 88.1126mm (3.469”)
c. It is not permitted to overbore a single cylinder; all cylinders must be bored equally.
d. Sleeving of cylinders is not permitted.
6.3. Crankshaft
a. OE Mazda MZR 2.0L (2009-2015) manual transmission crankshaft (part # LF9G-11-301) must be used with no modifications except for
machining or polishing polishing and/or machining of the bearing surfaces to allow the use of main and rod bearings as permitted
in Table 4 below.
Table 4: Crankshaft Measurements
easurement iameter Diameter
b. OE crankshaft (Mazda part # LF9G-11-301) must weigh a minimum of 31.75lb.
c. Maximum permitted stroke is as follows: 3.27” / 83.1mm
d. Shot peening is prohibited.
e. Bearings
1. Main and rod bearings must not be modified; coatings are not permitted.
2. OE bearings are permitted.
3. The only bearing sizes permitted other than OE are listed in see Table 5.
Sizes
Bearing Type Minimum Bearing
Width Minimum Bearing
Thickness Minimum Bearing
Weight Part #
Main Bearings
(Standard H) .630” 0.097” N/A 0000-01-5215-MB
Main Bearing
(Standard HX) .630” 0.097” N/A 0000-01-5216-MB
Rod Bearings
(Standard H) .630” 0.057” 28g 0000-01-5213-RB
Rod Bearing
(Standard HX) .630” 0.057” 28g 0000-01-5214-RB
f. The crank trigger must not be modified; it must be installed per the Mazda Factory Service Manual.
g. OE crank pulley/balancer (Mazda part # LF94-11-400) must not be modified and must be installed per the Mazda Factory Service Manual.
h. Knife edging of the crankshaft is not permitted.
i. Modifications to the crankshaft counterweights are not permitted.
j. Coatings, REM or metal treatments of any kind are not permitted.
k. Alternate shifter bushing located at the bottom of the shift lever is allowed.
6.4. Connecting Rods
a. OE Mazda MX-5 (2009-2015) manual transmission unmodified connecting rods (part # LF9G- 11-210) must be used. Connecting
rod weight with cap and bolts must not be less than 530 grams.
6.5. Pistons
a. Mazda Motorsports’ competition pistons (standard bore part # 0000-01-5310; oversized part # 0000-01-5310 OS) are required;
no modification is permitted.
b. The minimum weight of the piston, less wrist pin and hardware, must not be lighter than 290 grams.
c. Mazda Motorsports’ competition wrist pin (part # 0000-01-5310-PN) must be used.
d. The minimum weight of the wrist pin must not be lighter than 80 grams.
e. Modification of the piston ring end gap width is permitted.
6.6. Cylinder Head
a. Mazda Motorsports’ competition cylinder head (part # 0000-01-5300) must be used; no modi- fications to the cylinder head are
permitted outside of the gasket face surface outlined below in Table 6.
b. Intake runner CC volume is 182cc +/- 1cc.
c. Exhaust runner CC volume is 114cc +/- 1cc.
d. Combustion chamber volume may not be below 41cc.
e. The gasket face of the cylinder head may be resurfaced provided the maximum allowed compression ratio is not
exceeded.
I. Surfacing of the head gasket surfaced must be in a flat plane.
II. Cylinder head gasket surface distortion may not exceed .010mm or 0.004”.
f. The minimum height of the cylinder head as measured must be at least (TBA)
g. The following head gaskets in Table 6 below are permitted; no other gaskets may be used.
Table 6: Head Gasket Measurements
Description Thickness Mazda Part #
OE Gasket 0.017” approximate crush
depth L3G2-10-271A
Competition
Gasket 0.55mm (0.021”) 0000-01-5319-21
Competition
Gasket 0.75mm (0.030”) 0000-01-5319-30
Competition
Gasket 1.0mm (0.040”) 0000-01-5319-40
Competition
Gasket 1.3mm (0.051”) 0000-01-5319-51
6.7. Camshaft and Camshaft Timing
a. Camshafts must not be modified; see Table 7 for OE camshaft part numbers.
Table 7: Camshaft part numbers
Description Mazda Part #
Intake Cam L3E3-12-420
Exhaust Cam L309-12-441B
b. Camshaft and crankshaft sprockets must not be modified; see Table 8 for part numbers.
shaft Sprocket Part #s
t #
4X0C
425
c. Cam timing must not be altered; chain must be installed as stated in the Mazda Factory Service Manual.
d. OE timing chain (Mazda part # LF7A-12-201) is required; no modification is permitted.
e. OE timing chain components must be used; see Table 9 for Mazda part numbers.
Table 9: Timing Chain Guide Part #s
Description Mazda Part #
Fixed Guide LF01-12-614
Tensioner Guide LF01-12-671
6.8. Valves
a. OE valves must not be modified (including reshaping); see Table 10 for Mazda part numbers.
le 10: Valve Part #s
b. Valve location or angle must not be moved.
c. Valve guides may not be replaced.
d. Valve job measurements must be as follows:
1. Intake 35 top 45 seat 65 bottom 77 bottom seating angle width is 1.0mm
2. Exhaust 40 top 45 seating to radius seating angle width 1.2 mm.
3. Valve stem installed height must be per the Mazda Factory Service Manual.
4. Valve stem seals must be OE.
6.9. Valve Springs
a. Mazda Motorsports’ competition valve springs (part # 0000-01-5319-SP) are required.
6.10. Intake Manifold
a. OE intake manifold (Mazda part # LF9G-13-130B) is required; no modification is permitted (e.g., no material may be added or removed; no
painting or coating on the exterior or interior permitted).
b. All air entering the engine must pass through the throttle body and metered by the mass airflow sensor.
c. Removal of these factory EGR components is permitted: Valve, crossover pipe, coolant lines (EGR DELETE KIT 0000-06-5447)
d. If factory EGR components are removed, the following ports must be blocked:
1. Intake manifold cross over pipe port.
2. Cylinder head cross over pipe port.
3. EGR valve port on back of cylinder head.
6.11. Intake System
a. Cars must replace OE air box with the Mazda competition cold air intake kit (part # 0000-06- 5150-KT); no modification (e.g., ducting or
baffling of air, venturi cones) to the cold air intake kit is permitted.
b. No alteration to the intake tube length, diameter, or shape is permitted.
c. The air filter supplied in the Mazda Motorsports competition cold air intake kit may be refreshed
with the Mazda Motorsports’ competition air filter (part # 0000-06-5204).
6.12. Fuel System
a. Fuel must comply with SCCA GCR section 9.3.25
b. OE fuel pump (Mazda part # LFG1-13-350) is required; no modification is permitted.
c. It is permitted to remove the unleaded fuel restrictor from the filler neck. (GCR 9.3.26)
d. Mazda Motorsports’ competition fuel rail that includes fuel pressure gauge, and fuel sampling test port and hose kit (part #
0000-06-5207) is optional.
1. Fuel pressure sensor integrated into the required AIM data acquisition system is required. It must be operational and able to be
viewed when pulling a competitor on track data.
2. The addition of a switch or jumper located in the under-hood fuse box is allowed to acti- vate the fuel pump. This modification may
serve no other purpose.
3. One operational fuel sample test port is required. Fuel sample test ports shall be made from dry break fuel rated quick disconnects.
No other style of fuel sample test port is allowed (e.g., Schrader valves).
4. No other modifications permitted.
e. OE fuel pressure regulator (Mazda part # LFB6-13-280) is required.
1. Vehicle must run between 54 and 63 PSI of fuel pressure.
f. OE injectors (Mazda part # L3G5-13-250) are required; no modification is permitted.
1. Flow rates for the injectors must fall within the factory tolerance of 204-216ml (204-216 cc, 12.5-13.1 cu in/minute).
6.13. Lubrication System
a. OE engine oil filter is required; no substitutions permitted.
b. OE oil pump PT# L310-14-100J is required and no modifications are permitted.
c. Mazda Motorsports’ competition oil cooler adaptor kit with lines (part # 0000-01-5100KT) is required; no modification is
permitted.
d. Oil pressure sensor integrated into the required AIM data acquisition system is required. It must be operational and able to be
viewed when pulling a competitor on track data.
e. Oil and lubricants are unrestricted.
6.14. Engine Control Unit (ECU)
a. Reference penalties for non-compliance of the Spec ECU flash in Section 21 below. Modifica- tion or attempted modification of
the Spec ECU flash will result in a 12-month suspension from competition and $1,000.00 fine.
b. Mazda Motorsports’ competition ECU (part # 0000-01-5379) is required; serial number must be visible; external or internal
modification is not permitted.
c. ECU calibrations and inputs must not be modified.
d. OE engine electrical harness (part # NH18-67-020A) is required; no modification is permitted.
e. OBDII diagnostics port must be operational in all cars.
1. The check engine light must be operational and perform the function test at start up.
2. The OBDII port must be available at all times (including during the race) for tech officials to install test equipment as necessary.
3. If a competitor uses the OBDII port to power any type of data acquisition system, he/she would be responsible for providing the
splitter cable to plug in both units or unplug the data acquisition system.
f. Instrument panel clusters must be operational and unmodified OE parts.
g. Temporary data acquisition devices may be installed by the sanctioning body for technical compliance.
h. Removal of Mazda ECU insulator PT# LFG1-13-3C1 is permitted (diagram below)
6.15. Miscellaneous
a. The factory air conditioning system and all associated lines, compressor, condenser and evap- orator must be removed.
1. Once the AC compressor is removed, the OE AC pulley delete kit (Mazda part # LF17-15- 940E) is required.
b. Serpentine belt Gates PT# 6PK-2170 or same size equivalent is required.
7. Exhaust
a. OE exhaust manifold and OE heat shield must be replaced with Mazda Motorsports’ competi- tion part # 0000-06-5407-NC; no modification
is permitted (e.g., internal or external wraps, coatings, paints, metal treatments, thermal barriers etc.).
b. OE exhaust system must be replaced with Mazda Motorsports’ competition part # 0000-06- 5427-NC; no modification is permitted (e.g.,
internal or external wraps, coatings, paints, metal surface treatment, thermal barriers etc.).
c. The forward oxygen (O2) sensor (OE Lambda Sensor) must remain in the factory location and in full working order. Mazda Motorsports’
competition O2 sensor installation kit wiring extender (part # 0000-10-5320) is permitted.
d. The secondary post catalytic oxygen (O2) sensor must be removed.
e. Heat shielding
1. OE heat shield protecting ABS unit from header may not be removed or modified.
2. OE muffler heat shield may not be removed or modified.
3. It is permitted to wrap the exhaust pipe from the mid connection flange to the muffler.
(see red arrows in picture below)
4. Use of heat shielding material on transmission tunnel to replace OE heat shielding is permitted. OE heat shielding
must be removed from transmission tunnel. (see diagram below)
8. Cooling System
(cooling system
checklist)
a. Mazda Motorsports’ competition radiator and oil cooler assembly (part # 0000-01-5504-CR) is required (e.g., OE is not
permitted).
b. The radiator using the OE mounting brackets must be installed in its original location.
c. The oil cooler may not be moved or altered from the pre-assembled mounting location.
d. Radiator ducting may be placed on each side of the radiator tanks and the undertray to force air through the radiator fins. The
gap between the top and sides of the radiator may be sealed but shall not perform any other function.
e. The unmodified OE cooling fan must be maintained in full working order and mounted in the stock location. Axillary control of
the radiator cooling fan may be added to activate the fan independent of the ECU, OE control of the fan must remain intact.
f. Thermostats may be modified, removed or replaced.
g. The OE water pump (Mazda part # 1F70-15-100) is required; no modification is permitted.
h. The OE water pump pulley (Mazda part # L327-15-131) is required; no modification is permitted.
i. Engine cooling system hoses and clamps may be substituted.
j. The heater core may be removed along with HVAC evaporator core including all associated hard pipes and hoses. This is to include
OE water to oil cooler lines as well as throttle body coolant lines. (Rear coolant pipe 0000-01-5514, bottom coolant pipe 0000-
01-5515)
k. The OE engine coolant expansion tank may be replaced with any aftermarket part but and must not serve another purpose.
9. Clutch, Pressure Plate and Flywheel
a. Vehicle may use any combination of the options listed in Table 11 below.
Table 11: Clutch Component Part Numbers
Description Mazda Part #
Mazda Factory Clutch Disc LF05-16-460A
ACT Sprung Clutch Disc 0000-02-5420-AC
ACT Pressure Plate 0000-02-5405-AC
ACT Clutch and PP Kit 0000-02-5004-G6
Mazda Factory
Pressure Plate LF04-16-410A
b. The unmodified pressure plate must be bolted directly to the stock, unmodified flywheel.
c. OE flywheel (Mazda part # LF9G-11-500) is required. Factory Service Manual resurfacing specification is permitted; no
other modification is permitted.
d. Alternate clutch lines are permitted but must not serve another purpose.
e. Clutch components must adhere to the minimum weights listed in Table 12 below:
Table 12: Clutch Component Part Numbers
Description Minimum Weight (lb.)
Clutch disc 3.5
Pressure Plate 9.4
Flywheel 15.80
10. Transmission
a. OE 2006-2015 6-speed gearbox and 4.10 final drive ratio are required.
b. No modification of the internal parts and ratios are permitted except the installation of the unmodified parts contained in the Mazda
Motorsports MX-5 transmission upgrade kit (part # 0000-02-5700).
c. Mazda Motorsports Competition gear set 0000-02-6000 is allowed. Gear ratios are as follows: 1st - 3.82; 2nd - 2.26; 3rd - 1.64;
4th - 1.18; 5th - 1.00; 6th - 0.83/0.79. There are two (2) production 6th gears; either one is permitted.
d. Alternate shift knobs are permitted.
e. Nomex or aftermarket fireproof shift boots are permitted. Removal of the factory rubber shift boot is not permitted.
f. No treating, coating, polishing or modification of any transmission or components are permitted.
g. Fluids and/or lubricants may be substituted with any lubricant.
h. Updating or backdating of transmissions from 2006–2015 is permitted; unmodified OE shifters must be retained. The use of short throw
shifters is prohibited.
i. An single inspection hole (not to exceed 1.5” in diameter) in the bottom of the bell housing is permitted for the sole purpose of technical
inspection of the flywheel. It is permitted to plug or tape over theat hole.
j. Transmission cooler(s) are permitted.
11. Differential
a. Only the Following differentials are allowed.
1. Mazda Motorsports, unmodified, Torsen limited slip differential – 0000-02-5564
2. OE, unmodified, limited slip differential - Mazda part # MS03-27-200B
3. OE, unmodified, open differential are permitted.
b. RX-8 differential mounting bracket (Mazda part # F151-39-730B) is permitted.
c. Mazda Comp diff bushings 0000-04-5510 is permitted (MX-5 diff mount)
d. Polishing, metal treatment or coating of differential or axle components are not
permitted.
e. Removal of metal/rubber isolator on the pinion flange is permitted.
f. Differential cooler(s) are permitted.
12. Suspension and Steering: Suspension
Modifications are limited to the addition of the Mazda Motorsports Spec MX-5 kit; details are as follows (including all
modifications permitted):
a. OE control arms are required; no modification is permitted.
b. Mazda Motorsports’ TSB MX-5-002 must be followed re: the rear shock thread protector found in the “Spec MX-5: Four Pillars”
page on MazdaMotorsports.com. The thread protector must measure 1.250”. (The TSB will not be applicable to the supply from
Mazda Motorsports received after 7.15.2020 as they will have the updated thread protector.)
c. Anti-roll bar links may be replaced with Mazda part # 0000-04-5597-KT
1. Cockpit adjustability is not permitted.
d. Mazda Motorsports’ competition sway bars are required, mounting guidelines:
1. Metal shims up to 1/8” total thickness are permitted between each anti-roll bar mount shackle and the stock mounting
point on the chassis.
2. One end of the sway bar(s) may be disconnected as a suspension tuning aid.
3. The bar must remain in place and be solidly attached to the suspension on one end.
4. Sway bar end links must be installed on the unmodified stock attachment points.
e. Camber, caster, and toe are unrestricted within the limits of the unmodified factory adjust- ments in conjunction with Mazda
Motorsports front offset bushing (part # 000-04-5407-NC).
f. Minimum ride height is unrestricted.
g. Nuts & bolts may be replaced by similar items performing the same fastening function(s).
h. Relocation or reinforcement of any suspension parts or mounting points is not permitted, with the following exceptions:
1. Addition of spacers or washers on a horizontal plane is permitted at the rear lower shock mount to the spindle per the
shock installation instructions.
2. Updating to RX-8 rear toe link and rear trailing arm is permitted. See Table 13 below.
Table 13: Permitted RX-8 Trailing Arm and Toe Link Part #s
Description Mazda Part #
RX-8 Trailing Arm F189-28-200A
RX-8 Toe Link F189-28-45XA
i. OE power steering pump with pulley (Mazda part # NE51-32-650D) is required; Mazda Motor- sports Power steering flow
restrictor PT#- 0000-04-5532 is permitted; no other modification is permitted.
j. OE power steering rack (Mazda part #: NE51-32-110C) is required; no modification or reloca- tion is permitted.
k. Factory power steering reservoir may be replaced.
l. Wheel center caps must be removed.
m. All chassis, structural and electrical repairs must follow factory procedures, specifications, and dimensions as described in the
applicable service manual. Reinforcement (e.g., seam welding, material addition, etc.) is not permitted.
n. Steering lock mechanisms must be removed.
o. The distance from the outside of the wheel rim to outside of the opposing wheel rim for both the front and rear of the vehicle
must not exceed 69.5”.
I. The distance Measurement is obtained by measuring the distance between the wheel lips by going through
the wheel spokes at the bottom of the wheel at its widest point via tape measure. (Measure the outside wheel
lip of one wheel to outside wheel lip of the other wheel on same axle.)
p. Mazda Motorsports’ competition rear toe link (part # 0000-04-5426) is permitted; no modification is permitted.
q. Mazda Motorsport’s Spec MX-5 Suspension Kit includes the items set forth in Items in Table
14. seen below are components within this kit. No substitutions or modifications of parts are permitted. The
unmodified kits must be used in their entirety, except as specified.
Table 14: Spec MX-5 Suspension Kit (All parts are required; no modification is permitted.)
Description Location Mazda Part #
Shocks Front 0000-04-5291-SA
Rear 0000-04-5292-SA
Springs Front 0000-04-9700-08
Rear 0000-04-9400-07
Helper Springs Front/Rear 0000-04-9926
Front Penske
Mount Kit Front 0000-04-5359
Rear Penske
Mount Kit Rear 0000-04-5358
Sway Bar Kit Front and Rear 0000-04-5306-EB
Offset Bushings Front 0000-04-5407-NC
13. Hubs
a. OE RX-8 front hub (Mazda part # F189-33-04X) may be substituted in place of the OE Miata 2006-2015 front hub.
b. Mazda Motorsports’ competition RX-8 rear hub upgrade kit (part # 0000-04-5811-KT) may be substituted in place of the OE MX-
5 rear hubs; this unmodified kit must be used in its entirety.
c. OE RX-8 rear uprights, bearings, hubs, and hybrid axel may be used in place of OE MX-5 parts.
14. Brakes
a. OE brake rotors must be used and adhere to the specifications below in Table 15.
Table 15: Brake Rotor Dimensions
Location Diameter Notes
Front 290mm (11.4”) Vented
Rear 280mm (11.0”) Solid
Front backing plates/dirt shields may be removed.
(see see red arrow in diagram below)
b. Rear backing plates/dirt shields may be removed.
(see red arrow in diagram below)
c. Brake lines may be replaced with competition braided steel lines; option: Mazda Motorsports’ part # 0000-03-5212.
d. The Factory ABS system must remain intact, unmodified, and in full working order.
e. Brake slider pin may be used in either/both front location B25D-33-694. (This prevents a stuck sliding caliper due to the rubber
grommet)
f. Parking brake mechanisms and actuating components may be removed.
g. Brake fluid is unrestricted.
h. Mazda Motorsports’ competition brake duct kit (part # 0000-03-5301) is permitted.
i. The forward vertical inner fender panels may be modified to fit the brake kit hose to the fog light openings but may not be
modified to serve any additional purpose.
j. Mazda Motorsports’ competition brake pads are required; see eligible brake pad compounds in Table 16. No other brake pads
are permitted.
Table 16: Brake Pad part numbers
Pad Style Mazda Part # Notes
Front Pad 0000-03-5104-SP RST-3 compound
Rear Pad 0000-03-5116-29 RSL-29 compound
15. Wheels
The following unmodified wheel options below in Table 17 are permitted for use.
Table 17: WHEELS
Description Color Mazda Part #
17x7” OE Wheel Gun Metallic 99656-47070
17x7” OE Wheel Silver 99656-77070
Mazda Motorsports’ Competition MX-5 Wheel Gun Metallic 0000-04-5706-GM
Mazda Motorsports’ Competition MX-5 Wheel Silver 0000-04-5706-SL
a. Wheels may be painted.
b. Aftermarket (any) wheel studs and lug nuts are permitted., provided that a minimum of two he threads must protrude
beyond the lug nut with the wheel installed with a minimum of two (2) full threads showing; Wheel studs may not be gun
drilled.
c. Wheel spacers are not permitted.
16. Tires
a. Dry tires: Toyo RR P235/40/ZR17
b. Wet tires: Toyo RA1 P235/40/ZR17.
17. Electrical Equipment
a. OE ignition coils (Mazda part # L3G2-18-100B) are required; no modification is permitted.
b. Mazda’s competition spark plugs (part # 0000-10-R7IX-11) are required; no modification is permitted.
c. The crankshaft position sensor and crankshaft pulley relationship must be as specified in the 2006- 2015 MX-5 Factory Service Manual.
d. One of the two OE alternators (Mazda part # LF9H-18-300R-OA, L3P9-18-300D) is required; no modification is permitted.
e. The alternator must not be externally regulated or disabled in any way other than by the OE
production ECU/wiring circuit and master kill switch.
f. The electronic control module (ECM) control circuit for alternator charging must be OE - unmodified and operational.
g. One of the two OE alternator drive pulley part # AJ51-18-W10 (60mm), Part# L813-18- W11(55mm) is required; no modification
is permitted.
h. All sensors related to engine operating parameters must be used and must be stock, unmodi- fied Mazda parts for the correct year
of the vehicle on which they are installed.
i. Any and all sensors and their respective locations, mounts, and wiring harness leads may not be altered except as elsewhere in this
rule set. e Spec-MX-5 rules.
j. Any sensors required for non-OE gauges must be in addition to the Mazda sensors.
k. All alternate gauge and sensors must have independent wiring. Splicing, tapping, or altering
of the factory engine wiring harnesses is prohibited with the exception of adding an
aftermarket tachom- eter/shift light as follows:
1. It is permitted to splice into the yellow wire with the black stripe (pin 2BA - Ignition
Coil 1 control circuit) in the engine harness to obtain the tachometer signal for an
aftermarket tachometer or shift light.
2. Splicing must be done within 5” of the ECU.
l. Data acquisition’s sensor(s) may be added, provided they do not require splicing or
alteration to the factory engine wiring harness.
m. Batteries
1. Batteries may be replaced with those of an alternate manufacturer, provided they are of
similar amp-hour capacity, and size, including lead acid or AGM.; lLithium batteries are not
permitted.
2. Batteries must weigh no less than 18.0lb and no more than 35.0lb
3. Additional battery hold-down devices are recommended.
4. Battery MUST be moved from the original location to the passenger side
in the upper trunk area in front of the tail lamp. This will require the use
of a bulkhead that separates the driver / passenger compartment
completely from the trunk and the battery location. See section 5.I for
reference.
18. Roll Cage
a. Roll cage must adhere to SCCA’s current GCR Section 9.4 for Touring 4 cars; with the following exceptions:
1. One tube not to exceed 1.75” in diameter may be added which extends from the door bars to the rocker panel on each side.
The landing plate for this tube can be no longer than 5” in length. The landing plates must be centered between the front
and rear landing plates for the lower NASCAR or X brace bar.
2. Main hoop mounting plates may be on multiple planes; however, they must not be greater than 19” on any side.
b. Playboy MX-5 Cup car cages manufactured by Racing Cages, Inc. with the official serial number plate on the main hoop are
allowed to retain the lower door bar and two 3” attachment points to the rocker panel on both the driver’s side and passenger
side. No additional seam welding or lengthening of the original attachment points is allowed.
19. Safety
a. An electrical master (“kill”) switch is required. See current GCR Section 9.3 Master Switch.
b. Vehicle must be equipped with a driver’s restraint system meeting the specifications of current GCR Section 9.3 Drivers
Restraint System.
c. Installation of a fire extinguisher or fire system is required. See current GCR 9.3 Fire System.
d. Vehicle must have a driver’s side window safety net complying with current GCR Section 9.3 Window Safety Nets. Nets must be
mounted to provide protection in the event the driver’s door opens.
20. Data
Acquisition
1 A technical evaluation process for cars is available from the Series. Part of this process is the required download of AiM Data files after
each timed session (Qualifying 1 & 2, Races 1 & 2). Within 30 minutes of each timed session end, all Series Competitors MUST send
the AiM Data file (.XRK) for all timed laps of that session to the secure email address (data@specmx-5.com), where data will be
reviewed by AiM directly. Failure to adhere to this guideline from the Series, or having non- functioning data, may be grounds for
penalty or disqualification by the Series.
a. Vehicle must be equipped with current generation AiM data acquisition system (configurable in Race Studio 3) that can provide
on track data to AiM race studio 3. The data acquisition system may only read the OBDII/ECU data stream. It is not permitted
to alter/manipulate data to and from the ECU. The AiM system may be utilized to trigger a switch I.E., cooling fans or diff cooler
pumps but must be wired via a separate analog circuit.
Refer to Section 17: Electrical Equipment above for installation requirements.
b. The connection at the OBDII port for the AiM system may be made in either one of two ways:
1. Through a dedicated OBDII AiM adaptor.
2. By direct wiring to the back of the OBDII port within 3” of the ODBII connector.
c. Fuel pressure datalogging is required.
d. Oil pressure datalogging is required.
e. All cars must run the latest AIM Data Logger Spec MX-5 ECU Protocol
21. Mandatory
Video
Camera
Cars running in Spec MX-5 must have a functioning video recorder/camera during all qualifying and race sessions as described in 9.3.11.
Upon request by an SCCA official, competitors must provide their video recording/data, which may be used by the SCCA for any
purpose including but not limited to rule enforcement and marketing. Failure to comply with a video request from an official, or
having a non-functioning video recorder/camera ~~may~~ will be grounds for penalty or disqualification.
22. Parts
Confiscation
a. Tech officials may confiscate competitors’ parts for the purpose of verification of tech compliance.
23. Penalties Clarification – Non-Compliant Parts
Level Infraction Penalty
1 Non-compliant modification to any of the spec
parts, engine components, ECU/Elec- tronics or
modification to the chassis.
May suspend the driver (i.e. suspend) of the non-
compliant Spec MX-5 from competing in SCCA
events for the 12 months following the suspension.
A level 1 infraction carries a $1,000 fine.
2
Non-compliant modification to the suspen- sion or
drivetrain outside of level one infrac- tions: engine,
fuel system, charging system, exhaust, and intake
system.
May suspend the driver (i.e. suspend) of the non-
compliant Spec MX-5 from competing in SCCA
events for the 6 months following the suspension.
A level 2 infraction carries a $500 fine.
3 Use of an unauthorized or non-compliant part,
engine component, ECU/Electronics or chassis or
chassis part.
May suspend the driver (i.e. suspend) of the non-
compliant Spec MX-5 from competing in SCCA
events for the 12 months following the suspension.
A level 3 infraction carries a $1,000 fine
4
Non-compliance (non-modification such as
incorrect part)Use of an unauthorized or non-
compliant for any of the suspension or drive- train
part or component outside of level one infractions:
engine, fuel system, charging system, exhaust, and
intake system.
May suspend the driver (i.e. suspend) of the non-
compliant Spec MX-5 from competing in SCCA
events for the 6 months following the suspension.
A level 4 infraction carries a $500 fine

2024-09-01 SMX Committee) OE versus OEM Definitons

#36608 from Spec Mazda (SM/SMX · Rule change · TB 24-09 (2024-09 Fastrack)

Summary

wordingSMX Mazda Miata OE versus OEM definitions clarified in GCR Section 9.1.7.1.

As printed in Fastrack

In GCR, Replace Section 9.1.7.1 Spec MX-5 (SMX) with the attached:

2024-09-01 SMX Committee) Shifter Bushing

#36611 from Spec Mazda (SM/SMX · Rule change · TB 24-09 (2024-09 Fastrack)

Summary

wordingSM and SMX shifter bushing rules clarified: alternate bushing at shift lever bottom now allowed.

As printed in Fastrack

In section 9.1.7.1.D.6.3., add the following:
"k. Alternate shifter bushing located at the bottom of the shift lever is allowed."

2024-11-01 HP 1275 HP Spridget Level 2 Only

#36518 from Darryl Saylor · Rule change · TB 24-09 (2024-09 Fastrack)

Summary

fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.

As printed in Fastrack

In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows:
"(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows:
"(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"

2024-11-01 HP Request for Classification of 1989-1994 Suzuki Swift GT 16V Twin

#36858 from Jorge Fabian · Rule change · TB 24-11 (2024-11 Fastrack)

Summary

cars addedSuzuki Swift GT 89-94 newly classified to HP Pre at 1900 lbs, 1298cc DOHC fuel injected.

As printed in Fastrack

In HP Spec Lines, Classify Suzuki Swift GT (89-94) as follows:

A specification table follows in the original; it is not shown here.

2024-11-01 T2 Spec Corvette Change for T2

#37127 from Joe Aquilante · Rule change · TB 24-11 (2024-11 Fastrack)

Summary

tyres & wheelsT2 Spec Corvette now allows 295 R compound DOT tires as alternative to Nankang NS-2R.

As printed in Fastrack

In T2 Spec Lines, Spec Corvette, change Notes as follows:
"Cars must comply with all Spec Corvette rules dated 11-28-22 including fuel and tires. No tire treatment or rubber softeners are
permitted. Limited to 380 HP. Nankang NS-2R Tires conforming to Spec Corvette rules ~~are required~~ or a 295 R compound DOT
tire."

2024-12-01 T2 Redundant Verbiage Regarding Mustang Spec Lines for Driveshaft

#36484 from David Mead · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

wordingT2 and T3 Mustang spec lines remove redundant driveshaft alternate/aluminum allowance wording.

As printed in Fastrack

In T2 Spec Lines, change Notes as follows:
Ford Mustang V6 (11-14): "~~Alternate driveshaft is allowed.~~"
Ford Mustang Boss 302 (12-13): "~~Alternate driveshaft is allowed.~~"
Ford Mustang GT 5.0L (11-14): "~~Alternate driveshaft is allowed.~~"
Ford Mustang GT 5.0L (15-17): "~~Alternate driveshaft is allowed.~~"
Ford Mustang GT 5.0L (2018-): ~~"Alternate driveshaft is allowed~~. Springs up to 800#/in front and rear permitted. ~~Alternate~~
~~metallic driveshaft permitted.~~"
Ford Mustang Coupe GT & Shelby GT 4.6L (05-10): "~~Alternate driveshaft is allowed.~~"

Show 4 more lines

In T3 Spec Lines, change Notes as follows:
Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10): "~~Alternate driveshaft is allowed.~~"
Ford Mustang V6 (11-14): "~~Alternate driveshaft is allowed.~~"
Ford Mustang V6 (05-10): "~~An Aluminum driveshaft is allowed.~~"

2024-12-01 T2 Request Less Restriction for Ls-3 Engined C6 Corvette

#36810 from Joe Aquilante · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

fasterT2 Chevrolet Corvette C6 LS3 restrictor increases from 53mm to 56mm flat plate.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), change Restrictor Required as follows:
"LS3: ~~53mm~~ 56mm flat plate restrictor"

2024-12-01 SMX E&O SMX Regs 9.1.7.1.D.5.u-.w

#37070 from Greg Amy · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

wordingSMX allows OE instrument cluster relocation for aftermarket dash mounting, with wiring re-routed only; alternate gauges now permitted.

As printed in Fastrack

In GCR, Section 9.1.7.D.5.u-w, change as follows:
"u. ~~Alternate guages and instuments may be added.~~ The ~~original~~ OE instrument cluster must remain unmodified, connected and
functional. However, it may be relocated to allow the mounting of an aftermarket dash such as an AIM. The wiring to relocated
the dash may not be cut or extended, it may only be re-routed. The remainder of teh dashboard or panel must remain intact.
v. Alternate gauges and instuments may be added.
w. Modifications may be made to the foot pedals to improve the comfort and accessibility to the driver; relocation of mounting
points is not permitted.
1. Dead pedal/footrest and heel stop may be added.

Show 1 more lines

~~w. Instrument clusters must be unmodified parts.~~"

2024-12-01 T2 Fuel Emissions Components

#37076 from Derrick Ambrose · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

wordingT2, T3, T4 fuel cell installations may remove charcoal canisters, emissions valves, and sensors.

As printed in Fastrack

In GCR, Section 9.1.9.2.D.1.c. add the following:
"5. Removal of ancillary fuel tank equipment charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket
fuel cell installations."

2024-12-01 T2 fix brake wording

#37129 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

wordingT2, T3, T4 brake component wording clarified: 2-piece rotors allowed in T2 within 5% OE diameter, T3 within 2% OEM diameter.

As printed in Fastrack

In GCR, Section, 9.1.9.2.D.6. Brakes, change as follows:
"a. Components
1. The make and material of brake pads and linings may be changed.
2. Brake fluid may be substituted with any brake fluid.
3. Brake rotor dust shields may be removed or replaced to accommodate brake ducts.
4. Flexible rubber brake lines may be replaced with Teflon lined, metal braided hoses.
5. Any brake ducts are permitted, but they must serve no other purpose. Fender liners may be modified solely for routing and
attachment of brake ducts. Duct intake openings may be created by the opening of 2 sections up to 14.5 square inches each in

Show 10 more lines

the front fascia. The stock headlamp location is not permitted for brake ducting. Two alternative duct openings may be created
by the removal of the fog lights or 2 sections up to 14.5 square inches each of stock false grills originally located in the front
fascia.
6. Stock replacement brake rotors may be obtained from sources other than the manufacturer provided they are the exact
equivalent of the stock rotors. In T2 only - 2-piece rotors with ferrous metal rotor disks and aluminum hats are allowed, must be
within 5% of OE diameter. In T3 only - 2-piece front rotors with ferrous metal rotor disks and aluminum hats are allowed, must
be within 2% of OEM diameter. Drilled and slotted rotors are permitted.
7. Parking brakes, mechanisms, and actuating components may be removed.
8. Brake vacuum reservoirs sized 0.50 gallons or smaller are permitted. The port or fitting at the vacuum source may not be
modified, enlarged or relocated. The vacuum reservoir and brake booster must be a closed system."

2024-12-01 T2 Evaporative emissions systems

#37130 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

wordingT2, T3, T4 fuel cell cars may remove charcoal canisters, emissions valves, and sensors.

As printed in Fastrack

In GCR, Section, 9.1.9.2.D.1.c., add the following:
"5. Removal of ancillary fuel tank equipment; charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket
fuel cell installations."

2024-12-01 T2 Move Spec Boxster to T4

#37158 from Rob Piekarczyk · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

cars addedPorsche Spec Boxster moves to T4, minimum weight 2750 lbs, requires 3 Super Tour events before Runoffs eligibility.

As printed in Fastrack

In T4 Spec Lines, classify Porsche Spec Boxster, as follows:

A specification table follows in the original; it is not shown here.

2024-12-01 T2 Corvette Wheels

#37169 from Brian LaCroix · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

fasterT2 Chevrolet Corvette C6 Coupe/Grand Sport wheels widened to 18×11 or 19×13.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), change Max Wheel Size as follows:
"18 x 10 11 (F) 19 x 11 (R) or 18 x 11 (F) 19 x 13 (R)"

2024-12-01 HP MINI Cooper Spec Line Correction - Rear Brake Rotor Diameter

#37176 from Robert Bax · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

suspension & brakesHP Mini Cooper 02-06 rear brake rotor increases from 239/9.4 mm/in to 259/10.2.

As printed in Fastrack

In HP Spec Lines, Mini Cooper (02-06), change Brakes Std.mm/(in.) as follows:
"(F) 276/(10.9) Vented Disc (R) ~~239/(9.4)~~ 259/(10.2) Solid Disc"

Applies to Mini Cooper on this page: Tom Tuttle

2024-12-01 T2 BMW 320i Spec Line

#37204 from chi ho · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

wordingT4 BMW 320i 14-15 Spec Line expires 12/31/24 removed; Turner Motorsports intercooler #024703TMS02 allowed.

As printed in Fastrack

In T4 Spec Lines, BMW 320i (14-15), change Notes as follows:
"~~**This Spec line will expire 12/31/24, Please submit to appeal**~~ Turner Motorsports intercooler #024703TMS02 allowed."

2024-12-01 T2 Classification for a 2005 Cadillac CTS 3.6 liter 6 speed manual

#37224 from Timothy Nash · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

cars addedCadillac CTS 02-07 3.6L classified in T3.

As printed in Fastrack

In T3 Spec Lines, classify Cadillac CTS (02-07) as follows:

2024-12-01 T2 Please Consider Allowing Update to the C5 Corvette

#37298 from DAVID WOODLE · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

unclearT2 Corvette C5 Z06 restrictor split by engine: LS1 59mm, LS2 63mm, LS3 56mm FPR.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04), change Restrictor Required as follows:
"~~59mm FRP~~ LS1: 59mm FPR, LS2: 63mm FPR, LS3: 56mm FPR"

Applies to Chevrolet Corvette on this page: Josh Carroll, David Holmes, Patrick Howe, Evan Gold, Greg Nester, Michael Cheney, Luis Martinez

2024-12-01 T2 Major error in lane, but nobody ran it.

#37302 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

removedT2 Chevrolet Corvette Z06 (06-12) Spec Line deleted entirely.

As printed in Fastrack

In T2 Spec Lines, delete Chevrolet Corvette Z06 (06-12) Spec Line in its entirety.

2025-01-01 HP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line

#37119 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

fasterEP BMW 325i/is E30 (84-91) weight reduced 50–52 lbs across three spec lines to 2150, 2204, 2258.

As printed in Fastrack

In EP SPEC LINES, BMW 325i/is (E30) (84-91), change Weight as follows:
"~~2200~~ 2150
*~~2255~~ 2204
**~~2310~~ 2258"

2025-01-01 T2 BoP for the Various Mustangs

#37185 from Scotty B White · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

fasterT2 Ford Mustang GT 5.0L (11-14) weight reduced from 3575 to 3525 lbs.

As printed in Fastrack

In T2 Spec Lines, Ford Mustang GT 5.0L (11-14), change as follows:
Weight: "~~3575~~ 3525"

Applies to Ford Mustang on this page: Scotty B White

2025-01-01 T2 Remove spec lines that have expired

#37269 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

Summary

removedT2, T3, T4 remove nine, nine, and thirty-six expired spec lines respectively, effective 2025-01-01.

As printed in Fastrack

In T2, Effective 1/1/2025, delete for following Spec Lines in their entirety:
"~~Acura TL SHAWD (10-13)~~
~~Audi S4 (12-14)~~
~~Audi S5 (13-14)~~
~~Audi TT RS (2018-)~~
~~Cadillac ATS-V (16-17)~~
~~Cadillac CTS-V (06-07)~~
~~Chevrolet Camaro SS (98-02)~~

Show 49 more lines

~~Honda Civic Type-R (2017-)~~
~~Saturn Sky / Convertible (07-09)~~"
In T3, Effective 1/1/2025, delete for following Spec Lines in their entirety:
"~~Audi TTS Coupe (10-11)~~
~~Cadillac ATS (2015)~~
~~Chevrolet Cobalt (05-07)~~
~~Dodge SRT-4 (03-05)~~
~~Ford Fiesta ST (2014-)~~
~~Hyundai Genesis Coupe (2010-)~~
~~Hyundai Veloster Turbo (18-21)~~
~~Mini Cooper S (2016-)~~
~~Toyota Camry (11-15)~~"
In T4, Effective 1/1/2025, delete for following Spec Lines in their entirety:
"~~Acura Integra GS-R VTEC (3 or 4 door) (94-01)~~
~~Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05)~~
~~Chevrolet Cobalt SS, Sport Coupe (06-10)~~
~~Chevrolet Sonic RS (2011-)~~
~~Chrysler/Dodge Neon ACR SOHC (4 door) (01-02)~~
~~Dodge Dart (14-15)~~
~~Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99)~~
~~Fiat 500 Abarth (12-14)~~
~~Ford Focus SVT (02.5-04)~~
~~Ford Focus ZX4 ST (05-06)~~
~~Ford Focus (08-11)~~
~~Ford Mustang V-6 (01-04)~~
~~Honda Accord LX & EX (03-07)~~
~~Honda Accord LX-S/EX/EX-L (08-12)~~
~~Honda Civic Coupe Si (99-00)~~
~~Honda Civic SI (02-03)~~
~~Hyundai Elantra GLS (11-12)~~
~~Hyundai Tiburon V-6 (03-08)~~
~~Hyundai Veloster Turbo/ R-Spec (14-15)~~
~~Kia Forte Koup and Sedan LX/EX (10-13)~~
~~Kia Forte Koup and Sedan SX (10-13~~
~~Kia Forte Koup (14-15)~~
~~Mazda Protégé ES (2000)~~
~~Mazda Protégé 5 (02-03)~~
~~Mazda6 s (03-07)~~
~~Mitsubishi Eclipse GT (00-05)~~
~~Nissan Sentra SER (02-03)~~
~~Pontiac Firebird V-6 (96-02)~~
~~Scion tC (03-07)~~
~~Subaru Impreza (non-turbo) (04-06)~~
~~Toyota Celica GT (00-05)~~
~~Toyota Celica GTS/GT (00-05)~~
~~Volkswagen Golf TDI (2010)~~
~~Volkswagen Passat (12-14)~~
~~Volkswgen Passat TDI (12-14)~~
~~Volkswgen Passat 1.8T (2014-)~~"

2025-01-01 T2 Spec Corvette Line Clarification.

#37441 from Joe Aquilante · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

wordingT2 Spec Corvette clarifies braking, tires, cooling, suspension, and Spec+ upgrades; SC-3200, SC+-3300 lbs.

As printed in Fastrack

In T2 Spec Lines, Spec Corvette, change as follows:
Weight: "SC-3200, SC+-3300* See Notes Section"
Notes: "~~Cars must comply with all Spec Corvette rules dated 11-28-22 including fuel and tires. No tire treatment or rubber~~
~~softeners are permitted. Limited to 380 HP. Nankang NS-2R Tires conforming to Spec Corvette rules or a 295 R compound DOT~~
~~tire.~~ Cars must conform to Spec Corvette rules dated 11/2022. Master cylinder part number GM 19418187 and Booster part
number 19418516 permitted. Limited to 380 HP. Any 200tw 315 tire permitted if used on all 4 corners or a 295 R compound DOT
tire.
Modifications to Radiator Air Shroud to increase radiator cooling efficiency is allowed. Replacement of factory air shroud with

Show 8 more lines

other material is allowed. New air shroud cannot be wider than inside of frame rails. The front bumper must remain in factory
shape – unmolested and air shroud must mount to it in factory location. Upper Radiator Support must retain factory location.
Factory air dam must remain in its factory location.
All factory suspension pick up points must be maintained. Trackspec’s rear upper coilover offset shock mount may be used, part
number C56UPRMNT.
The following "Spec Corvette +" allowances are permitted with a base weight of 3300 lbs: 1) Penske double adjustable shocks, 2)
dry sump, 3) battery relocation, 4) Quaife limited slip differential, 5) T2 4 piston 13"
front brake system, 6) coil springs other than Eibach part number 0800.225.0550."

2025-01-01 HP Request to Update 1988-1991 Civic to Match 1988-1991 CRX

#37444 from ENRIK BENAZIC · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

fasterHP Honda Civic 1.5 88-91 weight reduced to 2175 lbs base, 2229 lbs with one asterisk, 2284 lbs with two asterisks.

As printed in Fastrack

In HP SPEC LINES, Honda Civic 1.5 (88-91), change Weight as follows:
"~~2245~~ 2175
*~~2301~~ 2229
**~~2357~~ 2284"

2025-02-01 T2 Mustang Update backdate

#37275 from Scotty B White · Rule change · TB 25-02 (2025-02 Fastrack)

Summary

unclearT2 Mustang GT 5.0L combines 2015-17 and 2018-23 with different restrictors: 63mm for Gen 2, 60mm for Gen 3.

As printed in Fastrack

In T2 Spec Lines, combine Ford Mustang GT 5.0L (15-17) and Ford Mustang GT 5.0L (2018-) and change as follows:
Delete in its entirety: "~~Ford Mustang GT 5.0L (15-17)~~"
"Ford Mustang GT 5.0L ~~(2018-~~)(15-23)"
Required Restrictor: ~~58mm flat plate restrictor~~ 2015-17 5.0 Gen 2 63mm FPR, 2018-23 5.0. Gen 3 60mm FPR"
Gear Ratios: "3.66, 2.43, 1.69, 1.32, 1.00, 0.65 or 4.69, 2.98, 2.14, 1.76, 1.52, 1.27, 1.00, 0.85, 0.68, 0.63 or 4.17, 2.34, 1.52, 1.14,
0.87, 0.69"
Notes: "Ford Performance Handling Kit part #M-FR3A-M8, Sway Bars in M-FR3A-M8 kit part #M5490-E or M5490-G, Rear Toe
Bearing part #M-5A460-M, Ford Performance Radiator part #M-8005-M8,Strut Tower Brace part# M-20201-M, Camber Bolts M-

Show 7 more lines

3B236-A, Solid Differential Bushings part#M-4425-M, Short Shift Kit part#M- 7210-M8, Solid Subframe Bushings part#M- 5872-
M, Dampers in Handling Pack part #M-18000-F, Ford OEM Performance Package Brembo front BBK and 380mm rotors permitted
(Ford PN M-2300-V) at no weight penalty. Alternate driveshaft is allowed. Springs up to 800#/in front and rear permitted.
Alternate metallic driveshaft permitted. Rear spring relocation to shock permitted with kit TBD. Ford Racing oil pan #M-6675-
M50BR permitted. BMR rear upper control arm camber links part #UTCA064 permitted. Track/Performance Package parts
permitted. ~~Mustang S550 2015-17 5.0 Gen2 and 2018-23 5.0. Gen3 reduce weight by 100Lb when using 4 piston stock or~~
~~Brembo brakes with 355mm rotors.~~"

Applies to Ford Mustang on this page: Scotty B White

2025-02-01 T2 BOP Adjustment for 2016 - Camaro SS/1LE

#37434 from Kurt Rezzetano · Rule change · TB 25-02 (2025-02 Fastrack)

Summary

slowerT2 Chevrolet Camaro 1LE gains 100 lbs to 3600, restrictor increases to 62mm FPR.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Camaro, 1LE (2016-), change as follows:
"Chevrolet Camaro, 1LE (20 16-25)"
Required Restrictor: "~~58mm~~ 62mm FPR"
Min Weight: "~~3500~~ 3600"

2025-02-01 T2 BMW M235iR TCS CHANGE REQUEST

#37470 from Werner Kordas · Rule change · TB 25-02 (2025-02 Fastrack)

Summary

wordingT2 BMW M235iR (-2016) now permits oil cooler, radiator per touring rules, and silicone charge pipe.

As printed in Fastrack

In T2 Spec Lines, BMW M235iR (-2016), add to Notes the following:
"Oil cooler and radiator permitted according to touring rules. Silicone charge pipe permitted."

2025-02-01 T2 Request to Classify Club Spec in Appropriate Touring Classes

#37523 from Andrew Benagh · Rule change · TB 25-02 (2025-02 Fastrack)

Summary

cars addedFord SCCA Club Spec Mustang classified T3 at 3350 lbs with driver; Mazda SCCA Club Spec MX-5 classified T4 at 2500 lbs with driver.

As printed in Fastrack

In T3 Spec Lines, classify Ford SCCA Club Spec Mustang (CSM) as follows:

A specification table follows in the original; it is not shown here.

2025-02-21 HP Effective date for Jan 2025 GCR updates

#37654 from Doug Piner · Rule change · TB 25-02 (2025-02 Fastrack)

Summary

slowerEP BMW Z3 2.5L requires 52mm flat plate intake restrictor; Z3 2.8L 55mm; 328i/is E36 58mm; 328i/ci E46 58mm; 325i/is E46 56mm; 325i/is E36 56mm; 325is M-Technic 56mm.

As printed in Fastrack

In EP Spec Lines, add to Notes as follows:
BMW Z3 2.5LL "(Effective 2/21/2025) 52mm Flat Plate Intake Restrictor is required."
BMW Z3 2.8L (97-00): "(Effective 2/21/2025) 55mm Flat Plate Intake Restrictor is required."
BMW 328i/is E36 (96-99): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required."
BMW 328i/ci E46 (01-06): "(Effective 2/21/2025) 58mm Flat Plate Intake Restrictor is required."
BMW 325i/is E46 (01-06): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."
BMW 325i/is E-36 (92-95): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."
BMW 325is M-Technic (1994): "(Effective 2/21/2025) 56mm Flat Plate Intake Restrictor is required."

Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21

2025-03-01 HP Request Competition Adjustment to BMW Z3 2.5L

#37120 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

slowerEP BMW Z3 and 3-series models get smaller intake restrictors: Z3 2.5L to 52mm, Z3 2.8L to 55mm, 328i to 58mm, 325i to 56mm.

As printed in Fastrack

In EP Spec Lines, change Notes as follows:
BMW Z3 2.5LL "(Effective 3/1/2025) ~~56mm~~ 52mm Flat Plate Intake Restrictor is required."
BMW Z3 2.8L (97-00): "(Effective 3/1/2025) ~~59mm~~ 55mm Flat Plate Intake Restrictor is required."
BMW 328i/is E36 (96-99): "(Effective 3/1/2025) ~~62mm~~ 58mm Flat Plate Intake Restrictor is required."
BMW 328i/ci E46 (01-06): "(Effective 3/1/2025) ~~62mm~~ 58mm Flat Plate Intake Restrictor is required."
BMW 325i/is E46 (01-06): "(Effective 3/1/2025) ~~60mm~~ 56mm Flat Plate Intake Restrictor is required."
BMW 325i/is E-36 (92-95): "(Effective 3/1/2025) ~~60mm~~ 56mm Flat Plate Intake Restrictor is required."
BMW 325is M-Technic (1994): "(Effective 3/1/2025) ~~60mm~~ 56mm Flat Plate Intake Restrictor is required."

2025-03-01 HP Interpretation of Production Rules on Mirrors

#37235 from Lawrence Slivinski · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

wordingEP, FP, HP: interior or exterior mirrors meeting rule 9.3.36 now permitted.

As printed in Fastrack

In GCR, add new rule as Section 9.1.5.E.10.f:
"Any interior or exterior mirror(s) that meets rule 9.3.36 may be used."

2025-03-01 T2 T2 BOP

#37312 from Touring Committee · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

slowerT2 BMW M2 CS Cup requires Red power stick #8324085 instead of Purple #8324089; Corvette C5 Z06 restrictor reduces to 58mm from 59mm.

As printed in Fastrack

In T2 Spec Lines, BMW M2 CS Cup 2020-, change Notes as follows:
"Effective 3/1/2025 It is mandatory to run the ~~“Purple” power stick part #8324089~~"Red" power stick part #8324085."
In T2 Spec Lines, Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04), change Required Restrictor as follows:
"Effective 3/1/2025 ~~59mm~~ 58mm"

Applies to Chevrolet Corvette on this page: Josh Carroll, David Holmes, Patrick Howe, Evan Gold, Greg Nester, Michael Cheney, Luis Martinez

2025-03-01 HP HP Class Adjustments

#37459 from Production Committee · Rule change · TB 25-01 (2025-01 Fastrack)

Summary

slowerHP Mazda 2 11-14 base weight up 50 lbs to 2045; all VW 80s models up 50 lbs to 2150 base.

As printed in Fastrack

In HP SPEC LINES, change Weight as follows:
Mazda 2 (11-14)
"(Effective 3/1/2025) ~~1995~~ 2045
*~~2045~~ 2096
**~~2095~~ 2147"
Volkswagen Golf (GTI, GT, GL) (85-92)
"(Effective 3/1/2025) ~~2100~~ 2150
*~~2153~~ 2204

Show 13 more lines

**~~2205~~ 2258"
Volkswagen Jetta (GLI, GL) (85-92)
"(Effective 3/1/2025) ~~2100~~ 2150
*~~2153~~ 2204
**~~2205~~ 2258"
Volkswagen Rabbit 1780
"(Effective 3/1/2025) ~~2100~~ 2150
*~~2153~~ 2204
**~~2205~~ 2258"
Volkswagen Scirocco 1780 (8-valve) (83-88)
"(Effective 3/1/2025) ~~2100~~ 2150
*~~2153~~ 2204
**~~2205~~ 2258"

2025-03-01 HP Weight Reduction for Honda S2000

#37466 from Michael Unger · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

fasterEP Honda S2000 1997cc base loses 75 lbs to 2375; 2157cc base loses 60 lbs to 2450.

As printed in Fastrack

In EP, Spec Lines make the following weight changes:

A specification table follows in the original; it is not shown here.

2025-03-01 HP Mazda 1999 Miata 1.8L

#37488 from Joe Carr · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

fasterEP Mazda MX-5/Miata 99-05 minimum weight drops to 2100 lbs, 2153 lbs with power adder, 2205 lbs with two adders.

As printed in Fastrack

In EP Spec Lines, make the following weight change:
Mazda MX-5 /Miata (99-05):
"~~2150~~ 2100
*~~2204~~ 2153
**~~2258~~ 2205"

2025-03-01 HP MINI Cooper (07-13) Spec Line Correction: Errors and Omissions

#37560 from Robert Bax · Rule change · TB 25-03 (2025-03 Fastrack)

Summary

slowerHP Mini Cooper 07-13 engine corrected to DOHC; valve lift limit reduced to 0.390 inches.

As printed in Fastrack

In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), change as follows:
Engine Type:
"4 Cyl
~~SOHC~~ DOHC"
Notes:
"Compression ratio limited to 11.0:1, Valve lift limited to ~~.450”~~.390"."

Applies to Mini Cooper on this page: Tom Tuttle

2025-04-01 T2 Please class the Darkhorse R in T2

#37295 from Touring Committee · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

cars addedFord Mustang Challenge Darkhorse R newly classified in T2 with 58 mm restrictor, 3775 lbs minimum weight.

As printed in Fastrack

In T2 Spec Lines, classify the Ford Mustang Challenge Darkehorse R.

A specification table follows in the original; it is not shown here.

2025-04-01 T2 T2 350Z Spec Line Cleanup

#37603 from Ben Slechta · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

wordingT2 350Z (03-08) removes detailed OEM part numbers and consolidates permitted modifications into simplified allowance list.

As printed in Fastrack

In T2 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo Spec Z (03-08), change Notes as follows:
"~~Nissan Motorsports: Shock Front left P/N E6110-SZ350 & Front right E6111-SZ350 & rear E6210-SZ350, Springs front P/N~~
~~54010-SZ350 & rear 55020-SZ350, F&R 5600S-SZ350, Front roll bar #54611-SZ350, Rear roll bar #562300-SZ350, Bushings P/N~~
~~(54541, 54560, 55045, 55148, 55149, 55152, 55153, 55158, 56218) - RRZ30 allowed. Nismo flywheel permitted. SPC Control~~
~~Arms 72125 and 72123 are allowed. Aftermarket flywheel permitted at minimum 14lbs. Aftermarket headers permitted, cold air~~
~~intake permitted. Aftermarket big brake kit 4 piston front permitted up to 355x32 SPL pro V3 front upper camber caster control~~
~~arms for the 350z part# SPLFUAZ33 permitted. SPL rear toe links part# SPL RTA Z33 permitted. Stillen part #400338 permitted.~~
~~44011-RC350 rear caliper kit permitted, 43206-SZ350 Right rotor permitted, 43207-SZ350 Left rotor permitted. Must conform to~~

Show 7 more lines

~~all SpecZ 2018 Edition rules. No other touring allowances beyond 2018 SpecZ edition rules or allowances listed~~
~~here.~~ Track/NISMO/S/R-Tune OEM aero options permitted, KW Motorsports: F&R 5600S-SZ350 permitted, Front sway bar max
37mm, Rear sway bar max 25mm, RRZ30 Oil Pump allowed, Performance alternative front upper control arms permitted,
Spherical bearings allowed, Springs up to 700 lbs./in. front/rear permitted, Aftermarket flywheel permitted at minimum 14lbs, Z1
350Z Intake Power Mod Kit permitted, Aftermarket headers permitted, Cold air intake permitted, Stillen part #400338 permitted,
Zspeed and Z1 alternative clutch slave permitted, Nissan rear diff cover #99996-35TDK or #383510C021 permitted, Nissan caliper
kit: 41001-FR350 and/or 44011-RC350 permitted."

2025-04-01 HP Request for Classification of Chevrolet Spark

#37755 from Kristian Smith · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

cars addedChevrolet Spark 16-22 classified HP Pre at 1850 lbs minimum weight, fuel injected, 1399 cc.

As printed in Fastrack

In HP Spec Lines, classify the Chevrolet Spark (16-22):

A specification table follows in the original; it is not shown here.

2025-04-01 HP Request to Lower Ford Festiva Minimum Weight to 1600 LBS

#37939 from Doug DeRonne · Rule change · TB 25-04 (2025-04 Fastrack)

Summary

fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.

As printed in Fastrack

In HP Spec Lines "Ford Festiva (88-93)" change as follows:
Weight:
"~~1700~~ 1600
*~~1743~~ 1640
**~~1785~~ 1680"
Notes:
"Compression ratio limited to ~~10.5~~ 11.0:1. Valve lift limited to .450”."

2025-05-01 T2 C6 T-2 Corvette 6 Liter Engine Restrictor

#37490 from Joe Aquilante · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

fasterT2 C6 Corvette LS2 restrictor increases from 63mm to 67mm FPR.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), Required Restrictor, change as follows:
LS2: "~~63mm~~ 67mm FPR"

2025-05-01 SMX Clarify Tire Marking Regs

#38004 from Greg Amy · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

wordingSMX Toyo RR P235/40/ZR17 tire rules clarified: one set per weekend, marking after first session, damage replacement procedures revised.

As printed in Fastrack

In GCR, Section 9.1.7.1.D.16.c., change as follows:
"1. ~~Cars in SMX are limited to running 1 (one) new (sticker) set, used tires or any of those combinations, of class specified Toyo~~
~~tires (Toyo RR P235/40/ZR17) per regular season Hoosier Super Tour event weekend during qualifying and races (not including~~
~~any test day sessions). Before the first dry qualifying or race (if rain in qualifying) session competitors will supply four Toyo RR~~
~~P235/40/ZR17 tires for marking to use during the entire weekend. Class specified rain tires will not be marked.~~ SMX cars are
limited to one set of Toyo RR P235/40/ZR17 per Hoosier Super Tour event weekend for all dry qualifying and race sessions. This
limitation does not include testing or practice sessions. Approved rain tires will not be required to be marked.
2. ~~A mandatory impound for all SMX competitors is required after the first dry qualifying or race (if rain in qualifying) session. It~~

Show 11 more lines

~~is the competitor’s responsibility to ensure their tires are marked prior to going on track for the next session.~~ A mandatory
impound for all SMX competitors will occur after the first dry qualifying or race session. All tires will be marked for the remainder
of the race weekend. It is the competitor’s responsibility to report to impound and ensure their tires are marked prior to leaving
impound.
3. ~~If a competitor damages a tire or wheel, and there is a safety concern, the competitor must find the Hoosier Super Tour Series~~
~~Tech Chief or SMX CCC, if assigned, for inspection. At the direction of the Hoosier Super Tour Series Tech Chief or SMX CCC, the~~
~~compet- itor will be allowed to substitute alternate used tire(s) to replace the damaged tire(s). New tires are not an option as a~~
~~replacement tire for a damaged tire.~~ If a competitor damages a tire or wheel and there is a safety concern, the competitor must
find the Hooseir Super Tour Series Tech Chief or SMX CCC, if assigned, for inspection. At the discretion of the Hoosier Super Tour
Series Tech Chief of SMX CCC the competitor may be allowed to substitute alternate used tires(s) to replace the damaged
tire(s). New tires are not an option as a replacement tire for a damaged tire."

2025-05-01 T2 370Z Mid link Replacement for True Coil Overs and OEM Wheel Size

#38014 from Zachary Hayward · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

fasterT2 Nissan 370Z max wheel size increases to 19 x 10.5 inches; mid link replacement for true coil overs now permitted.

As printed in Fastrack

In T2 Spec Lines, Nissan 370Z (09-17) / 370Z NISMO Edition (09-17), change as follows:
Max Wheel Size: "19 x 10 10.5"
Notes: "5300S-SS370 T-2 spring kit allowed; 54600-SS370 Sway Bars allowed 35mm (f). 29mm (r) Sports Package is allowed.
Springs up to 1000 lbs/in front and rear allowed. 54010- SZ350 (F) and 55020-SZ350 (R) allowed. Cold Air Intake allowed.
Performance Alternative Header permitted. Rear spring relocation permitted to allow coil over shocks. SPL suspension kit
permitted that includes: rear camber arms #SPL RLL Z34 or Nismo 551A0-RLLRZ, , SPL rear traction arms #SPL RTR Z34, or Nismo
55110-RTRRZ SPL front camber arms #SPL FUA Z34,or 54525-FUAZ4 SPL rear mid link #SPL RML Z34 or Nismo 551B0-RMLZ4. SPL
Part# SPL RTA Z34D or NISMO Part# 551B0-RTARZ permitted. Zspeed and Z1 alternative clutch slave permitted. The following

Show 1 more lines

STOPTECH parts are allowed with a 50 Lb penalty: #83.488.6800.51 front, 83.657.0057.51 rear."

2025-05-01 SMX SMX Data Submission Timeframe

#38039 from Jason Fichter · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

wordingSMX data submission deadline extended from 30 to 60 minutes after each timed session.

As printed in Fastrack

RM 25-04 Please update the data acquisition timeframe in GCR section 9.1.7.1.D.20
"20. Data Acquisition
1. A technical evaluation process for cars is available. Part of this process is the required download of AiM Data files after each
timed session (Qualifying 1 & 2, Races 1 & 2). Within 30 60 minutes of each timed session end, all competitors MUST send the
AiM Data file (.XRK) for all timed laps of that session to the secure email address (data@specmx-5.com), where data will be
reviewed by AiM directly. Failure to adhere to this guideline, or having non-functioning data, may be grounds for penalty or
disqualification."

2025-05-01 T2 T2 Cadillac tire

#38210 from Touring Committee · Rule change · TB 25-05 (2025-05 Fastrack)

Summary

fasterT2 Cadillac CT4-V Blackwing maximum tire size increases from 295 to 315.

As printed in Fastrack

In T2 Spec Lines, CT4-V Blackwing (2022-), change Tire Size Max as follows:
“~~295~~ 315”

2025-06-01 SMX SMX Data Submission - Penalties

#38248 from Kathy Barnes · Rule change · TB 25-06 (2025-06 Fastrack)

Summary

wordingSMX drivers must submit data acquisition files on time or face suspension and $250 fine.

As printed in Fastrack

In GCR, Section 9.1.7.1.23 add new level 5 infraction as follows:
Level: "5"
Infraction: "Failure to successfully submit (received by data@specmx-5.com) data acquisition file to data@specmx-5 per the
timeframes outlined in GCR section 9.1.7.1.20."
Penalty: "May suspend the driver (i.e. suspend) of the Spec MX-5 that failed to submit data on time or at all from competing in
SCCA events for the 3 months following the suspension.
A level 5 infraction may carry a $250.00 fine."

2025-06-01 HP Base Weight Adjustment for H-Production X1/9 Spec Lines

#38255 from Matthew Brannon · Rule change · TB 25-06 (2025-06 Fastrack)

Summary

fasterHP Fiat X-1/9 base weights reduced 50–53 lbs across 1300 and 1500 spec lines.

As printed in Fastrack

In HP Spec Lines, change Weight as follows:
Fiat X-1/9 & Bertone1500: “~~1790~~ 1740 *~~1835~~ 1784 **~~1880~~ 1827”
Fiat X-1/9 1300: “~~1650~~ 1600 *~~1691~~ 1640 **~~1733~~ 1680”
Fiat X-1/9 1300: “~~2060~~ 2010”
Fiat X-1/9 1500: “~~1950~~ 1900”

2025-06-01 SMX Committee) SMX Penaly Clarification updated language

#38337 from Spec Mazda (SM/SMX · Rule change · TB 25-06 (2025-06 Fastrack)

Summary

wordingSMX penalty language clarified: level 1 and 3 infractions may carry $1,000 fine; level 2 and 4 may carry $500 fine.

As printed in Fastrack

In GCR, Section 9.1.7.1.23. change as follows:
Rename as follows: "~~Penalties Clarification – Non-Compliant Parts~~ SMX Penalty Guidelines"
Change the Penalty language for level 1 to the following: "A level 1 infraction ~~carries~~ may carry a $1,000 fine."
Change the penalty language for level 2 to the following: "A level 2 infraction ~~carries~~ may carry a $500 fine."
Change the penalty language for level 3 to the following: "A level 3 infraction ~~carries~~ may carry a $1,000 fine."
Change the penalty language for level 4 to the following: "A level 4 infraction ~~carries~~ may carry a $500 fine."

2025-07-01 HP BMW Z4 update

#38490 from Bryce McGuire · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

slowerEP BMW Z4 03-05 restricted to 52mm flat plate intake restrictor.

As printed in Fastrack

In EP Spec Lines, BMW Z4 (03-05), add to Notes the following:
“52mm Flat Plate Intake Restrictor.”

2025-07-01 HP EP Fiat 124 Spider Competition Adjustment Request

#38498 from John Baucom · Rule change · TB 25-07 (2025-07 Fastrack)

Summary

fasterEP Fiat 124 Spider 1600 & 2000 weight drops 50 lbs to 2000; carburetors gain 2mm chokes to 36mm.

As printed in Fastrack

In EP Spec Lines, Fiat 124 Sport Spider 1600 & 124 Spider 2000, change as follows:
Weight: "~~2050~~ 2000"
Carburetor No. & Type: "(2) Weber 40 IDF-40IFI, (2) Solex C40P116, 34 36mm choke(s) req’d, (2) Weber 45DCOE w/ 34 36 mm
choke(s) on I.R. manifold or fuel injection."

2025-08-01 T2 Incorrect Touring Heading

#38451 from Terry Hanushek · Rule change · TB 25-08 (2025-08 Fastrack)

Summary

wordingT2, T3, T4 Spec Lines table header changed from T2 to ET.

As printed in Fastrack

In T2-T4 Spec Lines, change Table Header as follows:
"T2 ET"

2025-08-01 T2 Clarifications needed to BMW M2 CS cup line

#38536 from Joe Aquilante · Rule change · TB 25-08 (2025-08 Fastrack)

Summary

unclearBMW M2 CS Cup 2020 must run Red power stick part #8324085, not Purple #8324089.

As printed in Fastrack

The BMW M2 CS Clubsport is classed in T1, not T2. Please visit the following web address for vehicle details about the car's base
allowances-
https://www.bmwusa.com/motorsport/bmw-m2-
cs.html#:~:text=The%20BMW%20M2%20CS%20Racing%20models%20are%20powered%20by%20a,M2%20CS%20Racing%20Rec
ommended%20Mileage.
In T2 Spec Lines, BMW M2 CS Cup 2020, change as follows:
Model: "BMW M2 CS Cup 2020-2021"
Notes: "DOT approved tires required. All other components must be as homologated from BMW Motorsports. No other changes

Show 5 more lines

or Touring rule allowances permitted unless noted below. It is permitted to remove door glass and mechanism. ~~It is mandatory~~
~~to run the “Purple” power stick part #8324089. Effective 3/1/2025 5~~ It is mandatory to run the “Red” power stick part #8324085.
BMW exhaust part # 18302459928 allowed. Hot country package allowed including part numbers: (aKMK LH 17 10 8342846 1,
aKMK RH 17 10 8328139 1, 17 10 8328135 1, 17 10 8328136 1, 17 10 8328137 1, 17 10 8328138 1, ISO7380-2 M5X14 10.9 ZNSW
17 10 8436008 2, 17 10 8417424 1.) Hood vents conforming to 9.1.9.2.D.8.a.7 are permitted."

2025-08-01 T2 Fix brake allowance supersessions.

#38554 from Touring Committee · Rule change · TB 25-08 (2025-08 Fastrack)

Summary

slowerT2 Chevrolet Corvette C5 Z06 and C6 brake allowances clarified; stock calipers and rotors only for C5, specific sizes for C6.

As printed in Fastrack

In T2 Spec Lines, change Brakes as follows:
Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04): "(~~F) 325 Vented Disc (R) 305 Vented Disc May use two piece~~
~~steel rotors with aluminum hats up to 5% larger than 340/330; Any four piston calipers and brackets are permitted. Any brake~~
~~caliper pistons are allowed; may use the Wilwood SL6R brake caliper. Stock calipers and rotors only (F) 325 (R) 305~~"
Chevrolet Corvette C6 Coupe / Grand Sport (05-13): "(~~F) 325 / 340 Vented Disc (R) 305 / 330 Vented Disc or (F) 355 x 32 Vented~~
~~Disc (R) 340 x 26 Vented Disc or May use 2-pc steel rotors with alum. hats up to 5% larger than Z51 rotor. LS2 may use Grand~~
~~Sport brake package. Any brake caliper pistons allowed. May use any four piston brake caliper and brackets. Z06 brake calipers~~
~~allowed.~~"

2025-08-01 T2 C5 Corvette correction

#38782 from Touring Committee · Rule change · TB 25-08 (2025-08 Fastrack)

Summary

slowerT2 Chevrolet Corvette C5 LS1 restrictor reduced from 59mm to 58mm FPR.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04), change Restrictor Required as follows:
"LS1: 59 58mm FPR,
LS2: 63mm FPR,
LS3: 56mm FPR,
LS6: 58mm FPR"

Applies to Chevrolet Corvette on this page: Josh Carroll, David Holmes, Patrick Howe, Evan Gold, Greg Nester, Michael Cheney, Luis Martinez

2025-10-01 HP HP Plymouth Arrow spec omission

#38995 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

wordingHP Plymouth Arrow transmission max speeds clarified to 4 or 5.

As printed in Fastrack

In HP Spec Lines, Plymouth Arrow (76-80), add the following wording to Trans. Speeds(max):
"4 or 5"

2025-10-01 HP Add Wheel Diameter to Appendix G

#39008 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

wordingEP, FP, HP wheel diameter added to Appendix G as absolute maximum specification.

As printed in Fastrack

In Appendix G.2.3, change as follows:
"Rim width and diameter are is absolute maximums."

2025-10-01 HP Add TB ID tolerance to general Prod rules

#39009 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

wordingEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.

As printed in Fastrack

In GCR, Section 9.1.5.E., change as follows:
9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain
stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished."
9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must
remain stock (tolerance of +/-.25mm)."

2025-11-01 HP Please Lower Weight of 280Z

#38871 from Matthew Miller · Rule change · TB 25-09 (2025-09 Fastrack)

Summary

fasterEP Nissan 280Z minimum weight reduced from 2560 to 2400 lbs.

As printed in Fastrack

In EP Spec Lines, Nissan 280Z, change Weight (lbs) as follows:
"(Effective 11/1/2025) ~~2560~~ 2400
*~~2624~~ 2460
**~~2688~~ 2520"

2025-11-01 HP Miata Weight Adjustment Follow Up

#38949 from Don Tucker · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

fasterEP Mazda MX-5 1.8L 90-97 weight reduced to 2125 lbs from 2150 lbs.

As printed in Fastrack

In EP Spec Lines, Mazda MX-5 / Miata 1.8L (90-97), Effective 11/1/2025 make the following weight change:
"~~2150~~ 2125"

2025-11-01 HP Weight Break for 1098 Midget / Sprite

#38970 from Kendall Jones · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

fasterHP Austin-Healey Sprite/Midget 1098cc minimum weight drops 80 lbs to 1550.

As printed in Fastrack

In HP Spec Lines, Austin-Healey Sprite/Midget 1098cc, Effective 11/1/2025make the following weight change:
"~~1630~~ 1550"

2025-11-01 HP HP Volvo 142 spec omission

#38994 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".

As printed in Fastrack

In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes:
"Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."

2025-11-01 HP HP Mini DOHC 1.6

#38996 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)

Summary

slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".

As printed in Fastrack

In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following
changes to the Notes:
"Compression ratio limited to 11.0:1, Valve lift limited to ~~.450”~~.390"."

2025-11-01 HP Add to Rabbit description

#39019 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

wordingFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.

As printed in Fastrack

In FP Spec Lines, make the following spec line correction:
"Volkswagen Rabbit (Includes ~~Convertible~~ Cabriolet)"
In HP Spec Lines, make the following spec line correction:
"Volkswagen Rabbit 1588 (Includes Cabriolet)"
"Volkswagen Rabbit 1715 (Includes Cabriolet)"
"Volkswagen Rabbit 1780 (Includes Cabriolet)"

2025-11-01 HP Clean-up 9.1.5.E.7e

#39025 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

wordingEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.

As printed in Fastrack

In GCR, Section 9.1.5.E.7., change as follows:
"e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. N~~ote that the “Brakes Std.” and “Brakes~~
~~Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear~~
~~disc brakes under this rule~~. When converting from rear drum brakes to rear disc brakes:
1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on
the vehicle’s spec line.
2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. ~~The standard and~~
~~alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock~~

Show 3 more lines

~~from converting to rear disc brakes under this rule.~~
3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes
as stock from converting to rear disc brakes under this rule."

2025-11-01 HP Add TB size to Ford Mustang (94-98) Spec Line

#39130 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

wordingEP Ford Mustang (94-98) fuel injected throttle body inside diameter specified at 60.

As printed in Fastrack

In EP Spec Lines, Ford Mustang (94-98) add the following to the Fuel Injected Equipped Throttle Body Inside Diameter column:
"60"

2025-11-01 T2 ND Gearset Request for T4

#39166 from Josh Smith · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

wordingT3 and T4 Mazda MX-5 Miata models add approved gear kit PT#-0000-02-6100 to notes.

As printed in Fastrack

In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."
In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."
In T3 Spec Lines, Mazda MX-5 Miata (16-18), add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."
In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."

2025-11-01 T2 ND Spec Lines Wrong PT#'s

#39170 from Josh Smith · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

wordingT4 Mazda MX-5 Miata/Club/RF (19-24) and (16-18) remove discontinued hardtop part #0000-07-5901; T3 MX-5 Miata (16-18) and Global Cup ND (16-21) same.

As printed in Fastrack

In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), change Notes as follows:
"Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must remain
stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from moving
action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including
Mazda hardtop part #0000-07-5902-ND ~~and part #0000-07-5901 (discontinued DG Motorsports).~~ 29mm (f) 16mm (r) sway bars
allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02,
0000-02-5804-01). Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs
#0000-04-9700-08, springs up to 500lb front and 300lb rear allowed. Mazda tower brace 0000-04-5626 allowed. Mazda header

Show 20 more lines

0000-06-5410 allowed."
In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Notes as follows:
"Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Retractable hardtop option permitted
but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the
OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND ~~and part #0000-07-5901 (discontinued DG Motorsports)~~.
29mm (f) 16mm (r) sway bars allowed. Up to 500lb front and 300lb rear springs allowed. Mazda Motorsports Header part
#0000-06-5410 allowed. Mazda tower brace 0000-04-5626 allowed. 3rd and 4th gear may be replaced with the following parts-
(0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5."
In T3 Spec Lines, Mazda MX-5 Miata (16-18), change Notes as follows:
"Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Header permitted. Cold air intake
permitted. Front strut brace permitted. Front and rear sway bars permitted up to 35mm, Springs 800 front and 800 Rear max
permitted. Any OEM or aftermarket hardtop permitted that retains the OEM roof silhouette including Mazda hardtop part
#0000-07-5902- ND ~~and part #0000-07-5901 (discontinued DG Motorsports top).~~ If a hardtop is used, latches shall be replaced
with positive fasteners. Retractable hardtop option permitted but must be disabled from moving action and positively fastened.
In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, change Notes as follows:
"Shoulder harness installation must conform to FIA mounting specifications that are approved for this vehicle per section 6.2 FIA
article 253, safety equipment. Must meet all ND2 MX-5 Global Cup rules. Any OEM or aftermarket hardtop is permitted that
retains the OEM roof silhouette, including Mazda hardtop Mazda hardtop part #0000-07-5902-ND and #0000-07-5902-ND ~~part~~
~~#0000- 07-5901 (discontinued DG Motorsports).~~ If a hardtop is used, latches shall be replaced with positive fasteners. OBD2
requirement does not apply. Ballast box may be removed. ND2s with sequential gearbox allowed +100 lbs.

2025-11-01 T2 Touring 2 Post-Runoffs BOP Adjustments and Changes

#39274 from Touring Committee · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

fasterT2 Spec Corvette to 3200 lbs; Mustang 11-14 restrictor 60→62mm; Mustang 2015-23 tyre 295→315; 996 weights down to 3050/3000 lbs; 997.2 models restrictor 60→65mm, weights reduced 50 lbs.

As printed in Fastrack

In T2 Spec Lines, Spec Corvette, change as follows:
Weight: "SC3200 ~~SC+- 3300 See notes section~~"
Notes: "The following “Spec Corvette +” allowances are permitted ~~with a base weight of 3300 lbs~~:"
In T2 Spec Lines, Ford Mustang GT 5.0L (11-14), change Restrictor as follows:
"~~60mm~~ 62mm flat plate restrictor"
In T2 Spec Lines, Ford Mustang GT 5.0L (2015-23), change Tire Size as follows:
"~~295~~ 315"
In T2 Spec Lines, Porsche 911 / 996 (98-05), change Weight as follows:

Show 11 more lines

"3600: ~~3150~~ 3050
3400: 3000"
In T2 Spec Lines, Porsche Carrera S 997.2 (06-08), change as follows:
Restrictor: "~~60mm~~ 65mm FPR"
Weight: "~~3225~~ 3175"
In T2 Spec Lines, Porsche 911 / Carrera S 997.2 (09-12), change as follows:
Restrictor: "~~60mm~~ 65mm FPR"
Weight: "~~3300~~ 3250
In T2 Spec Lines, Porsche 911 / 997.2 GTS (09-12), change as follows:
Restrictor: "~~60mm~~ 65mm FPR"
Weight: "~~3400~~ 3350"

Applies to Ford Mustang on this page: Scotty B White

2025-11-01 T2 Adjust rev limit on Spec Corvette in T2

#39282 from Touring Committee · Rule change · TB 25-11 (2025-11 Fastrack)

Summary

slowerT2 Spec Corvette rev limit set to 7100 rpm.

As printed in Fastrack

In T2 Spec Lines, Spec Corvette, add to Notes the following:
"7) up to 7100 rpm Rev limit."

2025-12-01 T2 Help the 2011-2014 s197Mustang GT and Boss302 Less Restriction

#38523 from Joe Aquilante · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

fasterT2 Ford Mustang Boss 302 restrictor opens 56mm to 63mm; Mustang GT 5.0L 60mm to 65mm.

As printed in Fastrack

In T2 Spec Lines, Ford Mustang Boss 302 (12-13), change Restrictor as follows:
"~~56mm~~ 63mm flat plate restrictor"
In T2 Spec Lines, Ford Mustang GT 5.0L (11-14), change Restrictor as follows:
"~~60mm~~ 65mm flat plate restrictor"

Applies to Ford Mustang on this page: Scotty B White

2025-12-01 T2 Improving Competitiveness of Gen 5 Camaro SS

#39021 from Van Hunter · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

fasterT2 Chevrolet Camaro SS/1LE (10-15) minimum weight reduced to 3575 lbs.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Camaro SS/1LE (10-15), change Weight as follows:
"~~3625~~ 3575"

2025-12-01 HP Request to Re-Classsify Datsun SPL-311 to HP from FP

#39116 from Robert Heatwole · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

cars addedDatsun SPL-311 newly classified to HP at 2050 lbs with 1595cc OHV iron engine and specified carburetors.

As printed in Fastrack

In HP Spec Lines, classify Nissan/Datsun SPL 311 as follows:

A specification table follows in the original; it is not shown here.

2025-12-01 HP TR2 Notes E&O

#39180 from Anthony Parker · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.

As printed in Fastrack

In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes:
"Front apron assembly may be made of alternate material. ~~Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990~~
~~lbs.~~ Laycock overdrive, may use 5 speed gearbox without overdrive."

2025-12-01 HP Balance of Power

#39187 from Jim Simaras · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

slowerEP BMW Z3 2.5L restrictor reduced 52mm to 50mm, weight increased to 2550 lbs base; five other BMW models get smaller restrictors.

As printed in Fastrack

In EP Spec Lines, make the following changes to Restrictors:
BMW Z3 2.5L: "~~52mm~~ 50mm Flat Plate Intake Restrictor"
BMW Z3 2.8L (97-00): "~~55mm~~ 53mm Flat Plate Intake Restrictor"
BMW 328i/is E36 (96-99): "~~58mm~~ 55mm Flat Plate Intake Restrictor"
BMW 328i/ci E46 (01-06): "~~58mm~~ 55mm Flat Plate Intake Restrictor"
BMW 325i/is (E46) (01-06): "~~56mm~~ 53mm Flat Plate Intake Restrictor"
BMW 325is M-Technic (1994): "~~56mm~~ 53mm Flat Plate Intake Restrictor"
BMW 325i/is E-36 (92-95): "~~56mm~~ 53mm Flat Plate Intake Restrictor"

Show 4 more lines

In EP Spec Lines, BMW Z3 2.5L, change Weight as follows:
"~~2500~~ 2550
*~~2563~~ 2614
**~~2625~~ 2678"

2025-12-01 HP Alternative BOP Request for 84-87 Honda CRX/Civic

#39223 from Bill Lamkin · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

fasterHP Honda Civic and CRX models get wider 13-inch wheels: 6 to 7 inches.

As printed in Fastrack

In HP Spec Lines, change Wheels as follows:
Honda Civic: "13 x 6 7"
Honda Civic DX (92-95): "13 x 6 7"
Honda Civic/Si (84-87): "13 x 6 7"
Honda Civic 1.5 (88-91): "13 x 6 7"
Honda CRX/Si (84-87): "13 x 6 7"
Honda CRX 1.5(88-91): "13 x 67"

2025-12-01 T2 Adjust T2 Darkhorse R

#39346 from Andrew Aquilante · Rule change · TB 25-12 (2025-12 Fastrack)

Summary

slowerT2 Ford Mustang Challenge Dark Horse R (2024-) weight increases to 3825 lbs, displacement grows to 5038cc, tire width expands to 315.

As printed in Fastrack

In T2 Spec Lines, Ford Mustang Challenge, change as follows:
Car: "Ford Mustang Challenge ~~Darkehorse~~/Cup Dark Horse R (2024-)
Displacement: "~~92.220 x 92.7 / 4957~~ 93.0mm x 92.7mm 5038cc"
Weight: "~~3650 3775~~ 3825"
Restrictor: "2 x 55 mm"
Tires: "~~295~~ 315"
Notes: "Safety and camera equipment is unrestricted."
"**This ~~car~~ spec line is not eligible for the Runoffs until it has competed in 3 Super Tour events.**

Applies to Ford Mustang on this page: Scotty B White

2026-01-01 T2 Alternate Placement of Fuse Panel and Electronics Request

#39370 from Aaron Stehly · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

wordingT2, T3, T4 cars may relocate under-dash electronics and fuse boxes for access after roll cage installation.

As printed in Fastrack

In GCR, Section 9.1.9.2.D.9.d, add the following:
"8. Under-dash electronics including computers, modules and fuse boxes may be relocated so they can be easily accessed after
roll cage installation."

2026-01-01 T2 Rebalance Blackwing Cadillac T2 for 2026

#39426 from John Heinricy · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

fasterT2 Cadillac CT4-V Blackwing minimum weight drops 50 lbs to 3750.

As printed in Fastrack

In T2 Spec Lines, Cadillac CT4-V Blackwing (2022-), change Weight as follows:
"~~3800~~ 3750"

2026-01-01 T2 C6 LS2 Corvette Parity Request

#39472 from Brian LaCroix · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

fasterT2 C6 Corvette LS2 restrictor increases from 67mm to 80mm FPR.

As printed in Fastrack

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), change Restrictor as follows:
"LS2: ~~67mm~~ 80mm FPR LS3: 56mm FPR"

2026-01-01 T2 T2 Tire Sizing

#39490 from Scotty B White · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

fasterT2 Dodge Viper SRT10 coupe weight reduced from 3675 lbs to 3650 lbs.

As printed in Fastrack

In T2 Spec Lines, Dodge Viper SRT10 incl. coupe (03-06), change Weight as follows:
"~~3675~~ 3650"

2026-01-01 T2 Rear Spoiler for Mustang GT S550 (15-23)

#39499 from Andrew Aquilante · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

unclearT2 Ford Mustang GT 5.0L 15-23 permits Ford Track/Performance Package aero parts M-16600-FP and M-16601-MPP.

As printed in Fastrack

In T2 Spec Lines, Ford Mustang GT 5.0L (2015-2023), add to Notes the following:
"Ford Track/Performance Package parts permitted. Performance pack aero parts #M-16600-FP and #M-16601-MPP permitted."

Applies to Ford Mustang on this page: Scotty B White

2026-01-01 HP E/O: Improve Consistency of the Spec Lines

#39500 from Robert Bax · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

unclearHP Toyota MR-2 1.6L (85-89) compression ratio set to 11.0:1.

As printed in Fastrack

In HP Spec Line, Toyota MR-2 1.6L (85-89), change Comp. Ratio as follows:
"11.0:1"

2026-01-01 T2 Clarify T4 Brake Rotor Allowance

#39503 from David Mead · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

suspension & brakesT4 Performance now permits 1-piece alternative rotors matching spec line sizes; alternate brake kits allowed same.

As printed in Fastrack

In GCR, Section 9.1.9.2.D.6.a.6., change as follows:
"In T2-Performance alternative rotors, including 2 piece rotors are permitted. Rotors must be within 5% of OE diameter or a
maximum diameter of 360mm.
In T3- Performance alternative rotors, including 2 piece rotors are permitted with a maximum diameter of 360mm.
T4- Performance alternative 1-piece rotors are permitted but rotors must meet the sizes listed in the spec line. Spec lines
showing alternate brake kits are also permitted to use 1-piece performance alternative rotors of the same size."

2026-01-01 HP Request to Reclassify BMW 2002 Into H Production

#39567 from Jonathan Kinberg · Rule change · TB 26-01 (2026-01 Fastrack)

Summary

cars addedBMW 2002 newly classified to H Production at 2350 lbs with 1990cc iron block, 40 DCNF carburetor, 11.0:1 compression.

As printed in Fastrack

In HP Spec Lines, classify BMW 2002, as follows:

A specification table follows in the original; it is not shown here.

2026-02-01 T2 Request to Add 2014-2017 435i to T2

#38991 from Jimmy Cabrera · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

cars addedBMW 435i (2014-2017) added to T2 with 40mm restrictor, 3400 lbs minimum weight.

As printed in Fastrack

In T2 Spec Lines, classify as follows BMW 435I (2014-2017):

A specification table follows in the original; it is not shown here.

2026-02-01 T2 Consideration for Nissan Z & NISMO Z to Touring 2 Class

#39296 from Greg Nelson · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

cars addedNissan Z including Nismo added to T2 with 38mm restrictor, 3600 lbs base and 3650 lbs Nismo.

As printed in Fastrack

In T2 Spec Lines, classify Nissan Z incl. Nismo as follows:

A specification table follows in the original; it is not shown here.

2026-02-01 HP Triumph Spitfire 1296cc Compression Ratio Increase to 12:1

#39589 from Neil Verity · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

fasterHP Triumph Spitfire 1296cc compression ratio increases from 11.0 to 12.0:1.

As printed in Fastrack

In HP Spec Lines, make the following spec line changes:
Triumph Spitfire:
Carburetion
"Valves: (I) 33.0/(1.30) (E) 29.7/(1.17)
Comp. ratio ~~11.0~~ 12.0:1, Valve lift .450”
Trans. Speeds: 4"
Triumph Spitfire Mk. III & IV 1500:
Carburetion

Show 5 more lines

"1300 Valves: (I) 33.0/(1.30) (E) 29.7/(1.17)
1500 Valves: (I) 36.6/(1.44) (E) 29.7/(1.17)
1300: Comp. ratio 12.0:1, Valve lift .450”
1500: Comp. ratio 11.0:1, Valve lift .450”
Trans. Speeds: 4"

2026-02-01 T2 Allow Alt Bushing Material in Toe Links

#39607 from David Mead · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

fasterT2-T4 adjustable toe links now allow performance alternative bushings and spherical bearings, previously prohibited except in specified examples.

As printed in Fastrack

In GCR, Section 9.1.9.D.5.a.1., change as follows:
"T2-T4: A maximum of 3.5 degrees of negative camber is allowed on front and rear suspensions. Spec line part(s) may not be
modified to increase caster and camber. Strut suspensions may adjust camber and caster by the use of eccentric bushings,
eccentric bolts (crash bolts) at the strut-to-spindle, and/or by use of slotted adjustment plates at the top of the strut mounting
plate. If upper strut slotted adjustment plates are used, they shall be located on existing chassis structure, utilizing the
unmodified manufacturer’s original bolt holes and may not serve as reinforcement for that structure. Slotted adjustment plates
(strut camber plates) may incorporate a single spherical bearing (spherical bushing) and a ball thrust bearing per strut tower. On
other forms of suspension, camber and caster adjustment may be achieved by the use of shims and/or eccentric

Show 4 more lines

bushings. ~~Adjustable toe links with spherical bearings are permitted and may serve no purpose other than adjusting toe~~
~~angle.~~ Adjustable toe links are permitted. They are allowed to have performance alternative bushings and spherical bearings.
They may serve no purpose other than adjusting toe angle. Spherical bearings/bushings are not permitted in T2-T4 except for the
specific examples listed in the class rules or vehicle spec line."

2026-02-01 T2 Request for Classification of MG6 TCR in T2-TCR Class

#39702 from Vito Jin · Rule change · TB 26-02 (2026-02 Fastrack)

Summary

cars addedT2-TCR adds Link & Co 03 TCR and MG6 TCR, both 3000 lbs, 90% power, 275 max tire width.

As printed in Fastrack

In T2-TCR Spec Lines, classify Link & Co 03 TCR (2019-2025) and MG6 TCR (2019-2022) as follows:
T2-TCR Transmission Power Level Weight(lbs) Notes
Link & Co 03
TCR (2019-
2025)
SEQ 90% 3000 DOT approved tires with maximum section width
of 275. T2-TCR splitter and valance must comply
with 9.1.4.D.3.f. T2-TCR chassis ride height must

Show 7 more lines

comply with 9.1.4.1.A.1
MG6 TCR
(2019-2022)
SEQ 90% 3000 DOT approved tires with maximum section width
of 275. T2-TCR splitter and valance must comply
with 9.1.4.D.3.f. T2-TCR chassis ride height must
comply with 9.1.4.1.A.1

What the rules allowed changed as listed; this does not say what any particular car ran.