FA + FV + SRF3 at Buttonwillow Raceway Park

2023-03-01 SRF3 Update SRF Brake Rule

#33469 from Robey Clark · Rule change · TB 23-01 (2023-01 Fastrack)

In SRF, GCR section 9.1.8.D.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no
machining of any kind. Minimum thickness 12.20mm (0.481"). The 1985 Renault Alliance solid front rotor (Reference: Bendix
PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type
rotor. The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N
1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other
modification allowed. Wilwood caliper with bracket universal fit P/N 800038 may be used as delivered with no modification of
any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind;

A specification table follows in the original; it is not shown here.

2023-03-01 SRF3 Update SRF Bodywork Fitment Rule

#33765 from Robey Clark · Rule change · TB 23-03 (2023-03 Fastrack)

In Spec Racer Ford, GCR section 9.1.8.D.1.E, change as follows:
"j. Optional Bodywork Modification:
Viewing the tail section of the car from behind, draw a vertical line at the left and right ends of the outer vents from the bottom
edge of the bodywork up to a point two (2) inches below the crease at the lower edge of the vented panel. Make a vertical cut at
each line. The horizontal cut is to be one (1) inch below the crease at the base of the vented panel. Leave a one (1) inch radius at
each corner. Air Scoop (P/N 190000) must be installed in conjunction with rear cutout per Enterprises installation instructions.
SRF3 tail sections are allowed on SRFs. For purposes of tail section to center section fitment with the GEN3 airbox, shimming is
allowed at the rear of the center section. Shim material may be up to 19 mm (0.75") thick along the 1" upper square sidepod

2023-05-01 FA E&O - Correct Pro Formula Mazda spec line dimensional equivalent

#34085 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

In FA Table 2, Pro Formula Mazda spec line, change as follows:
"The overall maximum width of the bodywork behind the front wheels shall not exceed 132cm (51.17 51.97 inches)."

2023-05-01 SRF3 Update SRF Front W2 Rain Tire Part Number

#34118 from Robey Clark · Rule change · TB 23-05 (2023-05 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Front – Hoosier P/N 46100 1 P185/65R13 W2"

2023-05-01 FA Add new spec line for MSR Formula Mazda FMzR to Table 2

#34139 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

RM 23-06 – MSR - FMzR Formula Atlantic Classification dated 4/21/2023
In FA Table 2, add a spec line as follows:

2023-06-01 SRF3 Hoosier SRF Wet Front Tire Rule Update

#34189 from Robey Clark · Rule change · TB 23-06 (2023-06 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."

2023-06-01 FA Simplify Pro Formula Mazda wheel allowance

#34190 from Club Racing Board · Rule change · TB 23-06 (2023-06 Fastrack)

In FA, Pro Formula Mazda spec line, change wheel width as follows:
"Pro Mazda series wheels

A specification table follows in the original; it is not shown here.

2023-10-01 SRF3 SRF Radiator Rule Update

#34805 from Robey Clark · Rule change · TB 23-10 (2023-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.V.j, change as follows:
"Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be
replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent,
as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed
even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."

2023-12-01 FV FV Wheel Bearing Clarification

#35150 from Formula/Sports Racing Committee · Rule change · TB 23-12 (2023-12 Fastrack)

In FV, GCR section 9.1.1.C.10.G, change as follows:
"Front W wheel bearings"

2024-01-01 SRF3 Update SRF Rain / Brake Rule

#34706 from Robey Clark · Rule change · TB 23-09 (2023-09 Fastrack)

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with
incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes
GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the
wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain
light."

2024-01-01 SRF3 Update SRF Brake Light Rule v1

#34853 from Robey Clark · Rule change · TB 23-10 (2023-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the
original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No
changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake
Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as
a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."

2024-01-01 SRF3 SRF / SRF3 Rule Updates

#35268 from Robey Clark · Rule change · TB 24-01 (2024-01 Fastrack)

In SRF, GCR section 9.1.8.D.1.H, add the following:
"NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any
flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part
# P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to
improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting
support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad
"anti-rattle" clips must be removed."
In SRF, GCR section 9.1.8.D.1.V, add the following:

2024-06-01 SRF3 SRF3 Alternator Pulley Update In

#36095 from Robey Clark · Rule change · TB 24-06 (2024-06 Fastrack)

SFR3, GCR section 9.1.8.D.2.H.17, change as follows:
"Alternator Pulley: P/N G902130, or P/N G902130A, or P/N G902131 (six row). 12 11 oz minimum weight."

2024-08-01 SRF3 Update Rain Tire Rule and Hoosier Decal Placement

#36436 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used.
OR
Front – Hoosier P/N 46101 P185/65R13 W2
Rear – Hoosier P/N 46105 P205/60R13 W2

2024-09-01 SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info

#36624 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows:
"Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose
to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1)
decal must be located on each side of the car and one (1) decal must be visible on the front."

2024-10-01 SRF3 Update SRF3 Air Filter Rule

#36681 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.H.23, change as follows:
"Air Filter: P/N WM301020 or K&N RC-9160"

2024-10-01 SRF3 Update SRF Brake Rotor Thickness

#36687 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with
no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."

2024-10-01 SRF3 Hoosier Tire Decal Placement

#36739 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.B, change as follows:
"Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the
nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."

2024-10-01 FV Disc Brakes

#36822 from Guy Bellingham · Rule change · TB 24-10 (2024-10 Fastrack)

In FV, GCR section 9.1.1.C.4.D, change as follows:
"Any ferrous alloy, unvented rotor may be used, but must have a maximum diameter of 11.75 in. and a minimum thickness of
0.20 in. The otherwise smooth rotor may not be cross-drilled and may have a maximum of three pad cleaning grooves per side."

2025-02-01 FA Classify FR European Championship car as spec line car in Table 2

#37658 from Club Racing Board · Rule change · TB 25-02 (2025-02 Fastrack)

In FA Table 2, add the following:
Table 2 (Spec Line Cars)
Car Engine
Wheel
Width (in)
± .060
Aero Transmission Weight Notes

A specification table follows in the original; it is not shown here.

2025-03-01 FA Update Formula Renault 2.0 spec line notes

#37853 from Club Racing Board · Rule change · TB 25-03 (2025-03 Fastrack)

In FA Table 2, Formula Renault 2.0 (10-17) spec line, change the notes as follows:
"Engine must remain sealed. Car must comply with year-specific Formula Renault 2.0 manual, technical regulations, and all
applicable bulletins found here:. Competitors must have copies of these materials in their possession and present them upon
request.
https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/bulletins-techniques/2017,
https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/manuel-d-utilisateur/2017.
The following exceptions apply: Tire choice is unrestricted. No part of the car may be altered from original Formula Renault 2.0
components, except for necessary repairs that do not affect performance."

2025-04-01 SRF3 Driver Safety & Comfort

#37966 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.1.D, add the following:
"f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

2025-04-01 SRF3 Update SADEV transmission specs

#37992 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.2.K, change as follows:
"OR
SADEV-SRF3 6-Speed Sequential (beginning from Oct. 4, 2021 onward):
1st 12-36 3.0000 : 1
2nd 15-31 2.0667 : 1
3rd 18-28 1.5556 : 1
4th 22-28 1.2727 : 1
5th 24-26 1.0833 : 1

2025-07-01 FA Ligier JS F3 Tire Choice

#38434 from Rocco Magni · Rule change · TB 25-07 (2025-07 Fastrack)

In FA Table 2, FR Americas Ligier JS F3 spec line, change the notes as follows:
"Engine must be sealed in compliance with FR Americas or prior F3 Americas requirements. Car must comply with FR Americas
rules, with the following exception: front tires may be Hoosier P/N 43363, size 240/580R13 in MS compound, and rear tires may
be Hoosier P/N 43368, size 300/590R13 in MS compound. Competitors must have current copies of Formula Regional Americas
Championship Sporting Regulations, Onroak Automotive Ligier JS F3 Information Manual, and HPD engine-related specifications
and instructions in their possession and present them upon request."

2025-09-01 SRF3 SRF Rule Updates

#38853 from Robey Clark · Rule change · TB 25-09 (2025-09 Fastrack)

Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following:
"SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil
Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no
machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber
caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced
with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038

2025-10-01 SRF3 Add HD Oil Cooler

#38979 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.V.ff, change as follows:
"SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan
permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."

2025-11-01 FA Re-Consider USF Pro 2000 Car for Formula Atlantic Class

#38783 from Augie Pabst · Rule change · TB 25-09 (2025-09 Fastrack)

Effective 11/1/25 in FA Table 2, add the following:

2026-01-01 FA Alternate Intake Manifold for MZR

#38223 from Ove Olsson · Rule change · TB 26-01 (2026-01 Fastrack)

In FA, GCR section 9.1.1.2.d, modify as follows:
"9. Intake manifold must be unmodified Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT, 1.882” maximum bore
diameter at throttle plates. Elan or Mazda Speed equivalent Elite intake manifold may be replaced with unmodified intake Noor
P/N 0088-8-00 with intake runners AT Power P/N 13624."
"10. Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT intake manifold must use an A aluminum spacer must be
used between the intake manifold and cylinder head castings; minimum spacer length is 2.200”."

2026-01-01 FA Engine Compression Rule Change Request

#39302 from Reilly Harris · Rule change · TB 26-01 (2026-01 Fastrack)

In FA Table 2, Formula 1000 spec line, change the Engine as follows:
"Motorcycle-based 4-cycle up to 1000cc, maximum compression ratio 14.5:1;. o Otherwise, current FA engine rules apply."

2026-01-01 FA Change Formula 1000 allowances

#39608 from Club Racing Board · Rule change · TB 26-01 (2026-01 Fastrack)

In FA Table 2, Formula 1000 spec line, change the Notes as follows:
"Car must comply with December 2019 GCR Formula 1000 (FB) Preparation Rules, https://www.scca.com/downloads/48184-
gcr-december-2019/download, except as modified by this spec line. The prohibition of using carbon fiber in any external panels
or any panels licked by the airstream in Part 3.C of the December 2019 GCR F1000 (FB) Preparation Rules is removed, with the
exception that the car's floor pan/undertray must comply with the requirements of Part 2.D of the December 2019 GCR F1000
(FB) Preparation Rules. The prohibition of forward-facing gaps or openings in the bodywork in Part 3.I of the December 2019 GCR
F1000 (FB) Preparation Rules is removed. Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is modified as
follows: "Between the rear of the front tire and the front of the rear tire, no point on the lower surface of the car (the surface

2026-02-01 FA Pro Mazda Classification and Performance Enhancement Proposal

#39411 from Stephen Lamana · Rule change · TB 26-02 (2026-02 Fastrack)

In FA Table 2, Pro Formula Mazda spec line, change the notes as follows:
"All current FA rules apply to areas not covered by this spec line. Apex seals unrestricted. Street port or bridge port
allowed. Unmodified OEM l Lower intake manifold required unrestricted, upper intake manifold unrestricted. Balance tube not
permitted. Fuel injection only. Maximum 70 80mm T throttle B body. The maximum height of the wing and/or
endplates shall must not exceed 99cm (38.98 inches). The overall maximum width of the bodywork behind the front
wheels shall must not exceed 132cm (51.97 inches)."