This track has been raced on 2 configurations (The Circuit, 2.57 mi; 2.92 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One run is left out as not that car's own laps (far quicker than the car managed in any other session and than anyone else in its class all week; usually a swapped transponder): Tom Burt in Cal Club 2025 PM (1:42.300; the car's best in any other session was 1:52.334 and the rest of the class's best all week 1:50.233).
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Swift 016
FA
1
1:35.792Greg Labadie
1:35.792Greg Labadie
1:37.275Greg Labadie
163.8Greg Labadie
26.713Greg Labadie
26.816Greg Labadie
41.822Greg Labadie
Van Diemen RF01
FC
2
1:45.137Robert Armington
1:45.137Robert Armington
1:45.314Robert Armington
143.5Robert Armington
29.050Paul MacFarlane
30.109Robert Armington
45.728Robert Armington
Van Diemen DP-08
FC
1
1:45.137Robert Armington
1:45.137Robert Armington
1:45.314Robert Armington
143.5Robert Armington
29.106Robert Armington
30.109Robert Armington
45.728Robert Armington
Van Diemen RF01
FC
1
1:48.522Paul MacFarlane
1:50.067Paul MacFarlane
1:48.522Paul MacFarlane
114.4Paul MacFarlane
29.050Paul MacFarlane
31.137Paul MacFarlane
48.294Paul MacFarlane
Van Diemen RF96
FC
1
1:47.570Shawn Sarbacker
1:47.741Shawn Sarbacker
1:47.570Shawn Sarbacker
146.2Shawn Sarbacker
29.351Shawn Sarbacker
30.778Shawn Sarbacker
47.076Shawn Sarbacker
Van Diemen RF97
FC
1
1:47.993Bill Wallschlaeger
1:51.040Bill Wallschlaeger
1:47.993Bill Wallschlaeger
147.5Bill Wallschlaeger
29.638Bill Wallschlaeger
30.895Bill Wallschlaeger
47.233Bill Wallschlaeger
SCCA Ent SRF3
SRF3
38
1:50.233Caleb Shrader
1:50.233Caleb Shrader
1:50.825Caleb Shrader
138.9Paul Marino
30.136Caleb Shrader
31.672Caleb Shrader
44.841Tom Burt
Van Diemen RF
FC
1
1:58.213Greg Pizzo
2:10.106Greg Pizzo
1:58.213Greg Pizzo
127.3Greg Pizzo
32.045Greg Pizzo
34.162Greg Pizzo
51.126Greg Pizzo
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
FC Four Pot Calipers
#35481 from Steve Jenks · Rule change · TB 24-04 (2024-04 Fastrack)
neutralFC adds F2000 Metrik ZF2 with Ford Zetec engine and four-piston Brembo calipers as spec-line car.
In FC Table FC Charts, add the following: In FC, GCR section 9.1.1.B.1.c, change as follows: "The USF2000 tube frame Van Diemen car powered by the Mazda MZR LF-DE 2 liter engine and the F2000 Metrik ZF2 car equipped with 4-piston calipers is are added as a "spec line" cars in Formula Continental. Additional "spec line" cars are disfavored, and Balance of Performance (BoP) adjustments to keep "spec line" cars competitive with cars that meet the class formula are likewise disfavored." FC Charts Car Engine Wheel Width
Show 1 more lines
(in) ± .060 Aero Transmission Weight Notes
A specification table follows in the original; it is not shown here.
SRF3 SRF3 Alternator Pulley Update In
#36095 from Robey Clark · Rule change · TB 24-06 (2024-06 Fastrack)
fasterSRF3 alternator pulley minimum weight reduced from 12 oz to 11 oz.
SFR3, GCR section 9.1.8.D.2.H.17, change as follows: "Alternator Pulley: P/N G902130, or P/N G902130A, or P/N G902131 (six row). 12 11 oz minimum weight."
SRF3 Update Rain Tire Rule and Hoosier Decal Placement
#36436 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)
slowerSRF wet tires: P185/60R13 H20/W2 option removed; P185/65R13 W2 front now required with P205/60R13 W2 rear.
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used. OR Front – Hoosier P/N 46101 P185/65R13 W2 Rear – Hoosier P/N 46105 P205/60R13 W2
Show 8 more lines
1. It is forbidden to regroove tires. 2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for violation will be the loss of qualifying times and/or the disqualification of race results. 3. Hoosier SRF/SRF3 Decal Placement: Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises."
SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info
#36624 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)
neutralSRF Hoosier decal requirement reduced from four decals in specific locations to three decals with simpler placement rules.
In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows: "Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
SRF3 Update SRF3 Air Filter Rule
#36681 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
unclearSRF3 air filter rule removes K&N RC-9160 option, leaving only P/N WM301020 allowed.
In SRF, GCR section 9.1.8.D.2.H.23, change as follows: "Air Filter: P/N WM301020 or K&N RC-9160"
SRF3 Update SRF Brake Rotor Thickness
#36687 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
slowerSRF brake rotor minimum thickness increases from 12.20mm to 13.25mm, Wilwood vented rotor P/N 800065.
In SRF, GCR section 9.1.8.D.1.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."
SRF3 Hoosier Tire Decal Placement
#36739 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
neutralSRF3 Hoosier logo placement changes from four decals to three decals in different locations.
In SRF, GCR section 9.1.8.D.2.B, change as follows: "Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."
slowerFC tire limit reduced to four dry and four wet for Regional/Major/Super Tour, eight for Runoffs.
In FC, GCR section 9.1.1.B.10.h, change as follows: "(Effective 11/1/2024) FC is permitted a maximum of four (4) dry tires and four (4) wet tires for all Regional, Major, and Super Tour events; eight (8) dry tires and eight (8) wet tires are permitted for the Runoffs. This is effective beginning with the first (1st) qualifying session of the event. Marked tires are not required for The tire limit does not apply to testing or practice. It is the competitor's responsibility to ensure that the tires are declared, marked, and logged by Tech immediately upon conclusion of the first qualifying session, as provided in the event supplemental regulations, or per the instructions of the Race Director or Chief Steward. in advance of the tire(s) being used in a qualifying session or race. Failure to participate on marked Use of tires in excess of the number allowed will result in a penalty. Failure to participate on declared/marked/logged tires after the time
Show 6 more lines
prescribed for the same may result in a penalty. If a tire is damaged during a qualifying session or a race, the competitor may replace the damaged tire with a used tire upon approval by the Race Director or Chief Steward without loss of time or finishing position. Second or subsequent damaged tires may similarly be replaced upon approval by the Race Director or Chief Steward, but such will result in the loss of grid position in the subsequent race or session; the competitor will start at the back of the grid. Replacement of a damaged tire with a new tire upon approval by the Race Director or Chief Steward will result in loss of grid position in the subsequent race or session; the competitor will start at the back of the grid."
FC Change FF/FC Weight with Sequential Gearbox
#36651 from Robert Wright · Rule change · TB 24-11 (2024-11 Fastrack)
fasterFF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs.
In FF, GCR section 9.1.1.B.20.A.3, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight." In FC, GCR section 9.1.1.B.20.B.4, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
FA Classify FR European Championship car as spec line car in Table 2
#37658 from Club Racing Board · Rule change · TB 25-02 (2025-02 Fastrack)
neutralFA adds Tatuus F.3 T-318 or FR-19 as spec line car in Table 2 for Formula Regional European Championship.
In FA Table 2, add the following: Table 2 (Spec Line Cars) Car Engine Wheel Width (in) ± .060 Aero Transmission Weight Notes
A specification table follows in the original; it is not shown here.
Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21
FA Update Formula Renault 2.0 spec line notes
#37853 from Club Racing Board · Rule change · TB 25-03 (2025-03 Fastrack)
neutralFA Formula Renault 2.0 (10-17) spec notes clarified: engine sealed, manual compliance required, tire choice unrestricted, no alterations except repairs.
In FA Table 2, Formula Renault 2.0 (10-17) spec line, change the notes as follows: "Engine must remain sealed. Car must comply with year-specific Formula Renault 2.0 manual, technical regulations, and all applicable bulletins found here:. Competitors must have copies of these materials in their possession and present them upon request. https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/bulletins-techniques/2017, https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/manuel-d-utilisateur/2017. The following exceptions apply: Tire choice is unrestricted. No part of the car may be altered from original Formula Renault 2.0 components, except for necessary repairs that do not affect performance."
SRF3 Driver Safety & Comfort
#37966 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)
neutralSRF drivers with disabilities may modify seat and controls for safety and comfort with approval and logbook notation.
In SRF, GCR section 9.1.8.D.1.D, add the following: "f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
SRF3 Update SADEV transmission specs
#37992 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)
6th 25-23 0.9200 : 1 Final Drive Ratio: 15-48 3.20"
FA Ligier JS F3 Tire Choice
#38434 from Rocco Magni · Rule change · TB 25-07 (2025-07 Fastrack)
neutralFA Ligier JS F3 front tires may be Hoosier 43363 240/580R13 MS, rear 43368 300/590R13 MS.
In FA Table 2, FR Americas Ligier JS F3 spec line, change the notes as follows: "Engine must be sealed in compliance with FR Americas or prior F3 Americas requirements. Car must comply with FR Americas rules, with the following exception: front tires may be Hoosier P/N 43363, size 240/580R13 in MS compound, and rear tires may be Hoosier P/N 43368, size 300/590R13 in MS compound. Competitors must have current copies of Formula Regional Americas Championship Sporting Regulations, Onroak Automotive Ligier JS F3 Information Manual, and HPD engine-related specifications and instructions in their possession and present them upon request."
SRF3 SRF Rule Updates
#38853 from Robey Clark · Rule change · TB 25-09 (2025-09 Fastrack)
Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following: "SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual." Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038
Show 11 more lines
may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind; maximum of one spring per caliper. 1. Hawk Blue pads P/N 801993 only 2. Wilwood Vented Rotor P/N 800065 only, as delivered, with no machining of any kind. Minimum thickness 13.25mm (0.522") 3. Wilwood universal caliper Kit P/N 1180008 as delivered, caliper only P/N 800038; Wilwood knock back spring P/N 800045 may be used as delivered, with no machining of any kind, and only one spring per caliper 4. Renault caliper rubber bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185A 5. Renault caliper piston may be replaced with P/N 1196184 vented piston as delivered, with no machining of any kind 6. Girling .750" Master Cylinder P/N 880358 as delivered, with no machining of any kind 7. Wilwood .750" Master Cylinder P/N 880357 as delivered, with no machining of any kind 8. Tilton .750" Master Cylinder P/N 880360 as delivered, with no machining of any kind"
SRF3 Add HD Oil Cooler
#38979 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)
neutralSRF3 adds HD Oil Cooler P/N G1148500 as alternative to standard cooler P/N G480503.
In SRF, GCR section 9.1.8.D.1.V.ff, change as follows: "SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
FA Re-Consider USF Pro 2000 Car for Formula Atlantic Class
neutralFA class adds USF Pro 2000 car eligibility for Formula Atlantic racing.
Effective 11/1/25 in FA Table 2, add the following:
FA Alternate Intake Manifold for MZR
#38223 from Ove Olsson · Rule change · TB 26-01 (2026-01 Fastrack)
unclearFA MZR gains alternate Noor P/N 0088-8-00 intake manifold with AT Power runners as option to Elan or Mazda Speed Elite.
In FA, GCR section 9.1.1.2.d, modify as follows: "9. Intake manifold must be unmodified Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT, 1.882” maximum bore diameter at throttle plates. Elan or Mazda Speed equivalent Elite intake manifold may be replaced with unmodified intake Noor P/N 0088-8-00 with intake runners AT Power P/N 13624." "10. Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT intake manifold must use an A aluminum spacer must be used between the intake manifold and cylinder head castings; minimum spacer length is 2.200”."
FC F2000 MZR Spec Line Clarity/Revision Requested
#38927 from Rock Beauchamp · Rule change · TB 26-01 (2026-01 Fastrack)
neutralFC USF2000 Tube Frame may use Hewland LD200 4-speed H-pattern as alternative to Hewland JL-200 5-speed sequential.
In FC Charts table, USF2000 Tube Frame spec line, add the following to the Notes: "Cars originally built with the Hewland LD200 4-speed H-pattern may use that transmission as an alternative to the Hewland JL- 200 5-speed sequential transmission."
fasterFA Formula 1000 motorcycle-based engine loses maximum compression ratio 14.5:1 limit.
In FA Table 2, Formula 1000 spec line, change the Engine as follows: "Motorcycle-based 4-cycle up to 1000cc, maximum compression ratio 14.5:1;. o Otherwise, current FA engine rules apply."
FA Change Formula 1000 allowances
#39608 from Club Racing Board · Rule change · TB 26-01 (2026-01 Fastrack)
fasterFA Formula 1000 allows carbon fiber external panels, forward-facing gaps, raises floor to 125mm, adds eight 75×125mm rub blocks, expands diffuser to 110cm with 75mm radius transitions.
In FA Table 2, Formula 1000 spec line, change the Notes as follows: "Car must comply with December 2019 GCR Formula 1000 (FB) Preparation Rules, https://www.scca.com/downloads/48184- gcr-december-2019/download, except as modified by this spec line. The prohibition of using carbon fiber in any external panels or any panels licked by the airstream in Part 3.C of the December 2019 GCR F1000 (FB) Preparation Rules is removed, with the exception that the car's floor pan/undertray must comply with the requirements of Part 2.D of the December 2019 GCR F1000 (FB) Preparation Rules. The prohibition of forward-facing gaps or openings in the bodywork in Part 3.I of the December 2019 GCR F1000 (FB) Preparation Rules is removed. Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is modified as follows: "Between the rear of the front tire and the front of the rear tire, no point on the lower surface of the car (the surface
Show 7 more lines
licked by the air stream) shall be more than 125mm above the plane determined by the reference area designated by the entrant and on a line perpendicular to that reference plane." Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is also modified as follows: "A maximum of eight (8) rub blocks of maximum dimension 75mm by 125mm are allowed anywhere on the lower surface of the chassis and may extend below the reference plane." Part 3.E of the December 2019 GCR F1000 (FB) Preparation Rules is modified as follows: "The radius of transitions between the diffuser sides and adjacent horizontal structures may be up to 75mm. The width of the diffuser, as measured between its sides and above any radiused transitions, may not exceed 110cm in any lateral section." The CRB may require the use of Flat Plate Intake Restrictors at any time."
FC Adjust F2000 Metrik ZF2 weight
#39612 from Club Racing Board · Rule change · TB 26-01 (2026-01 Fastrack)
fasterFC F2000 Metrik ZF2 minimum weight reduced to 1220 lbs.
In FC Charts table, F2000 Metrik ZF2 spec line, change the Weight as follows: "1240 1220"
FA Pro Mazda Classification and Performance Enhancement Proposal
#39411 from Stephen Lamana · Rule change · TB 26-02 (2026-02 Fastrack)
fasterFA Pro Mazda: lower intake manifold now unrestricted, throttle body raised to 80mm, wing height must not exceed 99cm, bodywork width must not exceed 132cm.
In FA Table 2, Pro Formula Mazda spec line, change the notes as follows: "All current FA rules apply to areas not covered by this spec line. Apex seals unrestricted. Street port or bridge port allowed. Unmodified OEM l Lower intake manifold required unrestricted, upper intake manifold unrestricted. Balance tube not permitted. Fuel injection only. Maximum 70 80mm T throttle B body. The maximum height of the wing and/or endplates shall must not exceed 99cm (38.98 inches). The overall maximum width of the bodywork behind the front wheels shall must not exceed 132cm (51.97 inches)."
What the rules allowed changed as listed; this does not say what any particular car ran.