This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One run is left out as not that car's own laps (far quicker than the car managed in any other session and than anyone else in its class all week; usually a swapped transponder): Tom Burt in Cal Club 2025 PM (1:42.300; the car's best in any other session was 1:52.334 and the rest of the class's best all week 1:50.233).
5 laps are left out as timing errors (far too short to be a lap of this track). The rest of those sessions, sectors included, is used.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Pro Formula Mazda
FA
1
1:14.588Greg Labadie
1:14.588Greg Labadie
Swift 016
FA
1
1:35.792Greg Labadie
1:35.792Greg Labadie
1:37.275Greg Labadie
163.8Greg Labadie
26.713Greg Labadie
26.816Greg Labadie
41.822Greg Labadie
SCCA Ent SRF3
SRF3
38
1:50.233Caleb Shrader
1:50.233Caleb Shrader
1:50.825Caleb Shrader
138.9Paul Marino
30.136Caleb Shrader
31.672Caleb Shrader
44.841Tom Burt
Mazda Miata
STL
17
1:51.665Jared Korth
1:54.963Nick Leverone
1:54.845Gavin Wardle
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda MX-5
STL
6
1:51.665Jared Korth
1:57.404Ryan Gutile
1:54.845Gavin Wardle
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda Miata
STL
10
1:52.983Wesley Mollno
1:54.963Nick Leverone
1:55.682Nick Leverone
133.4Wesley Mollno
30.815Jon Davies
32.820Jon Davies
49.197Wesley Mollno
Mazda MX-5 (2015)
STL
1
2:00.239Adrian Comstock
2:00.239Adrian Comstock
2:00.722Adrian Comstock
133.0Adrian Comstock
32.847Adrian Comstock
34.493Adrian Comstock
52.675Adrian Comstock
Mazda RX-8
STL
1
1:53.515David LeCren
2:09.464David LeCren
2:11.372David LeCren
121.0David LeCren
31.217David LeCren
32.486David LeCren
49.550David LeCren
Honda Civic Si
STL
1
1:56.438Jonathan Lugod
1:57.331Jonathan Lugod
1:56.438Jonathan Lugod
106.8Jonathan Lugod
31.787Jonathan Lugod
33.468Jonathan Lugod
50.873Jonathan Lugod
Honda Prelude
STL
1
1:56.961Carl Young
1:57.917Carl Young
1:56.961Carl Young
104.5Carl Young
31.994Carl Young
33.745Carl Young
50.892Carl Young
Acura integra
STL
1
2:24.310Jack McEachern
2:24.310Jack McEachern
2:24.550Jack McEachern
77.6Jack McEachern
38.960Jack McEachern
41.141Jack McEachern
1:02.410Jack McEachern
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
slowerSRF Renault Alliance solid front rotors banned; restrictor reduced 35mm to 34mm for 2011+ Kawasaki; minimum weight increased to 1100 lbs for 2009+ stock engines.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481"). The 1985 Renault Alliance solid front rotor (Reference: Bendix PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type rotor. The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038 may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind;
Show 4 more lines
maximum of one spring per caliper." P2 Engine Table Spec Line Engine Series
A specification table follows in the original; it is not shown here.
wordingSRF3 tail sections allowed on SRFs with GEN3 airbox shimming up to 19 mm; alternate dash panel P/N 180100 or 180101 relocated in rules.
As printed in Fastrack
In Spec Racer Ford, GCR section 9.1.8.D.1.E, change as follows: "j. Optional Bodywork Modification: Viewing the tail section of the car from behind, draw a vertical line at the left and right ends of the outer vents from the bottom edge of the bodywork up to a point two (2) inches below the crease at the lower edge of the vented panel. Make a vertical cut at each line. The horizontal cut is to be one (1) inch below the crease at the base of the vented panel. Leave a one (1) inch radius at each corner. Air Scoop (P/N 190000) must be installed in conjunction with rear cutout per Enterprises installation instructions. SRF3 tail sections are allowed on SRFs. For purposes of tail section to center section fitment with the GEN3 airbox, shimming is allowed at the rear of the center section. Shim material may be up to 19 mm (0.75") thick along the 1" upper square sidepod
Show 11 more lines
tube. Mounting location cannot be modified or added. Shim material must be securely attached, but must not be welded. An alternate dash panel has been approved for use in Spec Racer Fords. The dash will be furnished by Enterprises only. P/N 180100 or 180101 k. Required Bodywork Modification: A 22.5" diameter wheel arch shall be cut in each side of the tail section. Viewing the tail section from the side, draw a vertical line at the drive axle centerline. Locate the top of the wheel arch at a point measured from the bottom edge of the tail section 9.25" vertically along the centerline. The 22.5" diameter circle intersects the bottom edge of the tail section 11.1" either side of the centerline. The tail section may be reinforced in the forward and aft portions of the wheel arch. Dimension tolerance is +/- 0.75". l. An alternate dash panel has been approved for use in Spec Racer Fords. The dash will be furnished by Enterprises only. P/N 180100 or 180101."
FA E&O - Correct Pro Formula Mazda spec line dimensional equivalent
fasterFA Pro Formula Mazda maximum bodywork width behind front wheels increases to 51.97 inches.
As printed in Fastrack
In FA Table 2, Pro Formula Mazda spec line, change as follows: "The overall maximum width of the bodywork behind the front wheels shall not exceed 132cm (51.17 51.97 inches)."
wordingSTL ITA/ITS RX7 and 1985+ ITA/ITS/ITB/ITC vehicles clarified to conform to section 9.1.4.2 tire specifications.
As printed in Fastrack
In STL Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Notes as follows: ITA-spec and ITS-spec RX7: "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires must also conform to 9.1.4.2.Tires." ITS, ITA, ITB, or ITC vehicles (1985- ): "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires must also conform to 9.1.4.2.Tires."
unclearSRF Hoosier wet front tire updated to P/N 46100 P185/60R13 H20 or W2.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."
wordingSRF radiator rule clarified: P/N 480466 replaceable with Automotive P/N 1R698, CU698 or manufacturer equivalent with documentation.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.V.j, change as follows: "Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent, as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."
wordingSRF rain/brake light now requires Super Bright LEDs Inc. P/N PT-STRB-R24 with specific connector and rain light switch.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain light."
wordingSRF requires Super Bright LEDs P/N PT-STRB-R24 rain/brake light with strobing capability and specific wiring.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."
STL Alternate Carburetor Request for 79-85 RX7 12a
unclearSTL Mazda RX-7 12A (79-85) now allows auto-type 2 bbl with 42mm choke(s) on dual-y manifold as alternate to stock Nikki 4 bbl.
As printed in Fastrack
In STL Table B: Alternate Vehicle and Engine Allowances, Mazda RX-7 12A (79-85), change Notes as follows: "Street Porting of the engine only. Bridge porting, peripheral porting, and eyelash porting are prohibited. Contact SCCA National Office for details of Street porting. Stock Nikki 4 bbl carburetor on a stock manifold only. or auto-type 2 bbl w/42mm choke(s) on a “dual-y” manifold. Allow the standard removal of emissions related components, and allow air and fuel jets to be corrected. Modification of the water jacket in the area of the spark plug for cooling purposes is permitted."
otherSRF adds brake duct and pedal extension rules, rear shift cable clamp option, camber limit to 5.0°, radiator opening height 3.5" ±0.5", and P2 engine restrictor changes.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.H, add the following: "NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part # P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad "anti-rattle" clips must be removed." In SRF, GCR section 9.1.8.D.1.V, add the following:
Show 23 more lines
"ii. Rear SADEV shift cable aluminum two-piece style clamp may be used. The P/N WM302007A clamp must serve no other purpose." In SRF, GCR section 9.1.8.D.1.X.k, add the following: "Negative camber shall must not exceed 5.0 degrees absolute maximum front and rear." In SRF, GCR section 9.1.8.D.1.AA.b, add the following: "2. Height of the radiator opening vertical surface 3 1/2“ +/- 1/2"." P2 Engine Table B.1 2008 and older Stock Suzuki, Yamaha, Honda, BMW 38.5mm P2 Engine Table B.2 Not required P2 Engine Table B.3 38.5mm Modified Engine 950 lbs. 1005cc max P2 Engine Table B.1 2008 and older 37mm P2 Engine Table B.2 Not required P2 Engine Table B.3 39mm Stock Engine 1050 lbs.
wordingSTL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems.
As printed in Fastrack
In GCR, Section 9.1.4.M.16., change as follows: "Power steering may be modified in any of the following ways: a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be modified internally to work without pump. b. an OEM manual steering rack for that model may be fitted c. an electric power steering pump may be fitted d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used e. an OEM hydraulic-assisted steering system may be used"
fasterSTL Acura/Honda B-series and Mazda MZR restrictors reduced 2mm; minimum weights down 25–75 lbs for 1900–2000cc engines.
As printed in Fastrack
In GCR, 9.1.4.H.1., change as follows: "Minimum weights for cars with normally aspirated piston engines will be determined by 1.35 lbs/cc displacement for the installed engine (see the following table). Displacement is the factory displacement for the installed engine. For the purpose of weight assignment, engine displacement will be rounded to the nearest 50cc (e.g., 2176cc = 2200cc and 2175cc = 2150cc)." In GCR, 9.1.4.H.1., change Minimum Weight on Chart as follows: Factory Engine Displacement 1900: "Effective 3-1-24: 2565 2540" Factory Engine Displacement 1950: "Effective 3-1-24: 2633 2583"
Show 11 more lines
Factory Engine Displacement 2000: "Effective 3-1-24: 2700 2625" In GCR, 9.1.4.H.3., change as follows: "Front wheel drive cars with a strut type front suspension may reduce their minimum weight by 2.5 percent. Effective 3- 1-24: Front wheel drive cars with 95" or less wheelbase must add 1.25% to their minimum weight." In STL Spec Lines, change Notes as follows: Acura/Honda B16: "Effective 3-1-24: 53 51mm" Acura/Honda B17: "Effective 3-1-24: 53 51mm" Acura/Honda B18C1: "Effective 3-1-24: 53 51mm" Acura/Honda B18C (JDM Type R), B18C5 (USDM Type R), B18C6 (UK and Euro Type R), B18C7 (Australia Type R): "Effective 3-1-24:52 50mm" Mazda MZR: "Effective 3-1-24: 52 50mm"
slowerSRF wet tires: P185/60R13 H20/W2 option removed; P185/65R13 W2 front now required with P205/60R13 W2 rear.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used. OR Front – Hoosier P/N 46101 P185/65R13 W2 Rear – Hoosier P/N 46105 P205/60R13 W2
Show 8 more lines
1. It is forbidden to regroove tires. 2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for violation will be the loss of qualifying times and/or the disqualification of race results. 3. Hoosier SRF/SRF3 Decal Placement: Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises."
SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info
wordingSRF Hoosier decal requirement reduced from four decals in specific locations to three decals with simpler placement rules.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows: "Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
slowerSRF brake rotor minimum thickness increases from 12.20mm to 13.25mm, Wilwood vented rotor P/N 800065.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."
wordingSRF3 Hoosier logo placement changes from four decals to three decals in different locations.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.2.B, change as follows: "Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."
STL Request to Remove Miata Hubs from General category
wordingSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
As printed in Fastrack
In GCR, Section 9.1.4.M.18., change as follows: "18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."
FA Classify FR European Championship car as spec line car in Table 2
wordingFA Formula Renault 2.0 (10-17) spec notes clarified: engine sealed, manual compliance required, tire choice unrestricted, no alterations except repairs.
As printed in Fastrack
In FA Table 2, Formula Renault 2.0 (10-17) spec line, change the notes as follows: "Engine must remain sealed. Car must comply with year-specific Formula Renault 2.0 manual, technical regulations, and all applicable bulletins found here:. Competitors must have copies of these materials in their possession and present them upon request. https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/bulletins-techniques/2017, https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/manuel-d-utilisateur/2017. The following exceptions apply: Tire choice is unrestricted. No part of the car may be altered from original Formula Renault 2.0 components, except for necessary repairs that do not affect performance."
wordingSRF drivers with disabilities may modify seat and controls for safety and comfort with approval and logbook notation.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.D, add the following: "f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
unclearSTL Mazda MX5 Challenge minimum weight now references GCR 9.1.7.1 instead of 2500 lbs; spec components removed, only alternative tires allowed.
As printed in Fastrack
In STL Spec Lines, Table B, Mazda Spec MX5 Challenge, change as follows: Minimum Weight: "2500 See 9.1.7.1." Notes: "Mazda MX5 Challenge car must utilize the following components: Roush CNC cylinder head 0000-01-5300,Mahle standard or +0.005 0000-01-5310, OEM camshaft, 11:1 compression ratio, header 0000-06-5407-NC, exhaust 0000-06-5427-NC, cold air intake 0000- 06-5150-KT, ECU flash 0000-01-5379, Pagid front brake pads 0000-03-5104-SP or endurance pads 0000-03- 5104-EN, Pagid rear brake pads 0000-03-5114-SP or endurance pads 0000-03-5114-EN, Penske front shock 0000-04-5291-SA, Penske rear shock 0000-04-5292-SA, Penske rear mount kit 0000-04-5358, Front mount kit 0000-04-5359, Front offset bushing 0000-04-5407-NC, Eibach front springs 0000-04-9700-08, Eibach rear springs 0000-04-9400-07, Eibach helper springs 0000-04-
Show 5 more lines
9926, Eibach front sway bar 0000-04-5306-FT, Eibach rear sway bar 0000-04-5306-RR, Interior finish panels 0000-07-5822, C&R radiator/oil cooler assembly 0000-01-5504-CR, Oil cooler adapter and lines 0000-01-5511-KT, ACT clutch 0000-02-5004-G6, wheels 17x8 #0000-04-5706-GM, # 0000- 04-5706-SL, and Toyo RR 235-40-17 dry, Toyo RA1 235-40-17 wet. Alternative tires on 17x7 wheels per STL rules. No other Super Touring modifications or allowances permitted except as noted in this spec line. Must conform completely to GCR 9.1.7.1, except alternative tires (only) per STL regs allowed."
Applies to Mazda Miata on this page: Jared Korth, Ricardo Arruda, Gavin Wardle, Ryan Gutile, Bryce Johnson, Andy Chittum, Adrian Comstock
tyres & wheelsFA Ligier JS F3 front tires may be Hoosier 43363 240/580R13 MS, rear 43368 300/590R13 MS.
As printed in Fastrack
In FA Table 2, FR Americas Ligier JS F3 spec line, change the notes as follows: "Engine must be sealed in compliance with FR Americas or prior F3 Americas requirements. Car must comply with FR Americas rules, with the following exception: front tires may be Hoosier P/N 43363, size 240/580R13 in MS compound, and rear tires may be Hoosier P/N 43368, size 300/590R13 in MS compound. Competitors must have current copies of Formula Regional Americas Championship Sporting Regulations, Onroak Automotive Ligier JS F3 Information Manual, and HPD engine-related specifications and instructions in their possession and present them upon request."
Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following: "SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual." Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038
Show 11 more lines
may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind; maximum of one spring per caliper. 1. Hawk Blue pads P/N 801993 only 2. Wilwood Vented Rotor P/N 800065 only, as delivered, with no machining of any kind. Minimum thickness 13.25mm (0.522") 3. Wilwood universal caliper Kit P/N 1180008 as delivered, caliper only P/N 800038; Wilwood knock back spring P/N 800045 may be used as delivered, with no machining of any kind, and only one spring per caliper 4. Renault caliper rubber bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185A 5. Renault caliper piston may be replaced with P/N 1196184 vented piston as delivered, with no machining of any kind 6. Girling .750" Master Cylinder P/N 880358 as delivered, with no machining of any kind 7. Wilwood .750" Master Cylinder P/N 880357 as delivered, with no machining of any kind 8. Tilton .750" Master Cylinder P/N 880360 as delivered, with no machining of any kind"
otherSRF3 adds HD Oil Cooler P/N G1148500 as alternative to standard cooler P/N G480503.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.V.ff, change as follows: "SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
FA Re-Consider USF Pro 2000 Car for Formula Atlantic Class
unclearFA MZR gains alternate Noor P/N 0088-8-00 intake manifold with AT Power runners as option to Elan or Mazda Speed Elite.
As printed in Fastrack
In FA, GCR section 9.1.1.2.d, modify as follows: "9. Intake manifold must be unmodified Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT, 1.882” maximum bore diameter at throttle plates. Elan or Mazda Speed equivalent Elite intake manifold may be replaced with unmodified intake Noor P/N 0088-8-00 with intake runners AT Power P/N 13624." "10. Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT intake manifold must use an A aluminum spacer must be used between the intake manifold and cylinder head castings; minimum spacer length is 2.200”."
fasterFA Formula 1000 motorcycle-based engine loses maximum compression ratio 14.5:1 limit.
As printed in Fastrack
In FA Table 2, Formula 1000 spec line, change the Engine as follows: "Motorcycle-based 4-cycle up to 1000cc, maximum compression ratio 14.5:1;. o Otherwise, current FA engine rules apply."
fasterFA Formula 1000 allows carbon fiber external panels, forward-facing gaps, raises floor to 125mm, adds eight 75×125mm rub blocks, expands diffuser to 110cm with 75mm radius transitions.
As printed in Fastrack
In FA Table 2, Formula 1000 spec line, change the Notes as follows: "Car must comply with December 2019 GCR Formula 1000 (FB) Preparation Rules, https://www.scca.com/downloads/48184- gcr-december-2019/download, except as modified by this spec line. The prohibition of using carbon fiber in any external panels or any panels licked by the airstream in Part 3.C of the December 2019 GCR F1000 (FB) Preparation Rules is removed, with the exception that the car's floor pan/undertray must comply with the requirements of Part 2.D of the December 2019 GCR F1000 (FB) Preparation Rules. The prohibition of forward-facing gaps or openings in the bodywork in Part 3.I of the December 2019 GCR F1000 (FB) Preparation Rules is removed. Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is modified as follows: "Between the rear of the front tire and the front of the rear tire, no point on the lower surface of the car (the surface
Show 7 more lines
licked by the air stream) shall be more than 125mm above the plane determined by the reference area designated by the entrant and on a line perpendicular to that reference plane." Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is also modified as follows: "A maximum of eight (8) rub blocks of maximum dimension 75mm by 125mm are allowed anywhere on the lower surface of the chassis and may extend below the reference plane." Part 3.E of the December 2019 GCR F1000 (FB) Preparation Rules is modified as follows: "The radius of transitions between the diffuser sides and adjacent horizontal structures may be up to 75mm. The width of the diffuser, as measured between its sides and above any radiused transitions, may not exceed 110cm in any lateral section." The CRB may require the use of Flat Plate Intake Restrictors at any time."
FA Pro Mazda Classification and Performance Enhancement Proposal
fasterFA Pro Mazda: lower intake manifold now unrestricted, throttle body raised to 80mm, wing height must not exceed 99cm, bodywork width must not exceed 132cm.
As printed in Fastrack
In FA Table 2, Pro Formula Mazda spec line, change the notes as follows: "All current FA rules apply to areas not covered by this spec line. Apex seals unrestricted. Street port or bridge port allowed. Unmodified OEM l Lower intake manifold required unrestricted, upper intake manifold unrestricted. Balance tube not permitted. Fuel injection only. Maximum 70 80mm T throttle B body. The maximum height of the wing and/or endplates shall must not exceed 99cm (38.98 inches). The overall maximum width of the bodywork behind the front wheels shall must not exceed 132cm (51.97 inches)."
What the rules allowed changed as listed; this does not say what any particular car ran.