This track has been raced on 4 configurations (The Circuit, 2.57 mi; 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
5 laps are left out as timing errors (far too short to be a lap of this track). The rest of those sessions, sectors included, is used.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Formula Enterprise
FE2
1
1:12.402Blake Pigeon
1:12.402Blake Pigeon
SCCA Ent FE2
FE2
7
1:13.988John Yeatman
1:13.988John Yeatman
1:39.712Paul Marino
156.6Paul Marino
27.234Paul Marino
28.582Paul Marino
43.028Jon McClintock
SCCA Ent FE2 (2007)
FE2
1
1:13.988John Yeatman
1:13.988John Yeatman
SCCA Ent FE2 (2010)
FE2
1
1:14.003Thomas W Burt
1:14.003Thomas W Burt
SCCA Ent FE2
FE2
5
1:39.265Jon McClintock
1:39.265Jon McClintock
1:39.712Paul Marino
156.6Paul Marino
27.234Paul Marino
28.582Paul Marino
43.028Jon McClintock
Chevrolet Camaro
GT2
3
1:42.698Tim Carroll
1:42.698Tim Carroll
1:44.128Tim Carroll
149.2Jean Meynet
28.543Jean Meynet
29.839Tim Carroll
44.262Tim Carroll
Ford Mustang
GT2/T3
6
1:45.818Brad McAllister
1:45.818Brad McAllister
1:46.926Brad McAllister
137.2Scotty B White
28.729Brad McAllister
30.833Brad McAllister
45.847Brad McAllister
Dodge Challenger
GT2
1
1:46.922Ben Valentine
1:46.922Ben Valentine
1:47.171Ben Valentine
132.9Ben Valentine
29.689Ben Valentine
30.929Ben Valentine
45.990Ben Valentine
Porsche GT3
GT2
2
1:47.914Rocky Crocker
1:47.914Rocky Crocker
1:48.433Rocky Crocker
155.7Rocky Crocker
29.826Rocky Crocker
31.456Rocky Crocker
46.030Rocky Crocker
Porsche GT3
GT2
1
1:47.914Rocky Crocker
1:47.914Rocky Crocker
1:48.433Rocky Crocker
155.7Rocky Crocker
29.826Rocky Crocker
31.456Rocky Crocker
46.030Rocky Crocker
Porsche GT3 Cup
GT2
1
1:57.745Robert Kelley
1:57.745Robert Kelley
1:58.760Robert Kelley
125.1Robert Kelley
32.864Robert Kelley
33.998Robert Kelley
50.578Robert Kelley
Chevrolet Corvette
GT2
1
1:49.904Igor Lyustin
1:50.345Igor Lyustin
1:49.904Igor Lyustin
145.8Igor Lyustin
30.271Igor Lyustin
31.850Igor Lyustin
47.568Igor Lyustin
Mazda RX-3
STU
1
1:50.913Tony Rivera
1:50.913Tony Rivera
1:52.737Tony Rivera
135.2Tony Rivera
30.415Tony Rivera
32.456Tony Rivera
47.999Tony Rivera
Mazda RX-7
GT2/STU
4
1:51.013Guy Laidig
1:51.013Guy Laidig
1:52.486Guy Laidig
138.7Guy Laidig
30.134Guy Laidig
32.225Guy Laidig
47.907Guy Laidig
Porsche 986 Boxster
T3
1
1:51.337Reto Eberle
128.4Reto Eberle
29.898Reto Eberle
33.530Reto Eberle
54.812Reto Eberle
Mazda Miata
STU
1
1:51.602Whitfield Gregg
2:02.264Whitfield Gregg
2:01.538Whitfield Gregg
116.3Whitfield Gregg
30.652Whitfield Gregg
32.263Whitfield Gregg
48.687Whitfield Gregg
BMW M3
STU
1
1:52.380Wilson Powell
1:55.401Wilson Powell
1:53.843Wilson Powell
102.6Wilson Powell
30.577Wilson Powell
32.372Wilson Powell
49.215Wilson Powell
Honda S2000
STU
1
1:53.640Rylan Hazelton
1:55.834Rylan Hazelton
1:53.640Rylan Hazelton
134.8Rylan Hazelton
30.582Rylan Hazelton
32.779Rylan Hazelton
49.779Rylan Hazelton
Nissan 370Z
T3
1
1:56.241Gamaliel Aguilar-Gamez
1:56.241Gamaliel Aguilar-Gamez
1:56.899Gamaliel Aguilar-Gamez
131.8Gamaliel Aguilar-Gamez
31.456Gamaliel Aguilar-Gamez
33.615Gamaliel Aguilar-Gamez
50.788Gamaliel Aguilar-Gamez
BMW 330ci
STU/T3
2
1:56.492Sean Lovett
1:56.492Sean Lovett
1:57.049Sean Lovett
136.3Ron Tanemura
31.816Sean Lovett
33.669Sean Lovett
50.941Sean Lovett
BMW 330
STU
1
1:56.492Sean Lovett
1:56.492Sean Lovett
1:57.049Sean Lovett
133.7Sean Lovett
31.816Sean Lovett
33.669Sean Lovett
50.941Sean Lovett
BMW 330ci
T3
1
1:59.844Ron Tanemura
1:59.844Ron Tanemura
1:59.971Ron Tanemura
136.3Ron Tanemura
32.188Ron Tanemura
34.401Ron Tanemura
52.107Ron Tanemura
Dodge VIPER
GT2
1
1:57.753Robert Kelley
2:00.453Robert Kelley
1:59.538Robert Kelley
92.9Robert Kelley
31.983Robert Kelley
33.965Robert Kelley
51.553Robert Kelley
Nissan 300ZX
STU
1
1:59.183James Slechta
1:59.183James Slechta
2:00.458James Slechta
132.0James Slechta
32.882James Slechta
34.528James Slechta
51.773James Slechta
BMW Z4M
T3
1
1:59.315J. David Orem
2:00.000J. David Orem
1:59.698J. David Orem
128.1J. David Orem
32.480J. David Orem
34.645J. David Orem
51.770J. David Orem
Mazda MX-5
STU
2
1:59.707Oscar Jackson
2:04.115Dale Shoemaker
1:59.707Oscar Jackson
125.9Dale Shoemaker
32.339Oscar Jackson
34.219Oscar Jackson
52.330Oscar Jackson
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
T3 T3 Boxster S GCR request
#33687 from Kelly Peebles · Rule change · TB 23-03 (2023-03 Fastrack)
neutralT3 Porsche Spec Boxster tire rule updates to current SPB rules or any 245 DOT tire.
In T3 Spec Lines, Porsche Spec Boxster, change Notes as follows: "Must conform to all SPB rules in the PCA rulebook. Each competitor shall have available definitive current documentation of the PCA rules. Tires must meet 2016 Current SPB rules or any 245 DOT tire permitted. No other touring allowances permitted."
Applies to Porsche 986 Boxster on this page: Reto Eberle
T3 OEM VW Steering Spindle Replacements 06-10 VW GTI and Jetta
neutralSTU Mazda BP5A classified at 1839 cc maximum displacement, 2023-04-01.
In STU Spec lines, classify Mazda BP5A as follows: STU Maximum Displacement (cc's) Minimum Weight Notes Mazda BP5A 1839 Chart May use engine in its entirety or specific components from the engine.
GT2 Request to class 2011 Porsche Cayman S
#33771 from Coyote Black · Rule change · TB 23-05 (2023-05 Fastrack)
neutral2009-2012 Porsche Cayman S classified in GT2, 3.4L, RWD, no PDK transmission allowed.
In GT Cars - Porsche, classify Porsche Cayman ‘S’ as follows: GT Cars - Porsche Model Years Body Style Drive- line Wheel- base (in) Notes Porsche Cayman ‘S’ 09-12 2 dr. Coupe RWD 95.08 3.4L No PDK Transmission
GT2 Please classify Fields Cardinal V8
#33784 from James Rogersn · Rule change · TB 23-05 (2023-05 Fastrack)
neutralFields Cardinal V8 classified in GT1 with Ford V8 engine, 4.9L displacement, 2100 lbs minimum weight.
In GT Spec Lines, GT1 Cars - Fields Cardinal, classify Fields Cardinal V8 as follows: GT1 Cars – Fields Cardinal Model Years Body Style Drive- line Wheel- base (in) Notes Fields Cardinal V8 2023 2 Dr. RWD 92.0 Roll Cage MUST be modified to comply with
Show 6 more lines
GCR Section 9.4. In GT Spec Lines, GT1Engines - classify Ford V8 as follows: GT1 Engines - Ford Engine Family Engine Type Bore x
A specification table follows in the original; it is not shown here.
neutralT3 adds 2022 Toyota GR Cup and GR86 Cup, both 2387cc, 2700 lbs, 245/620R18 slicks, 332x32F/280x32R brakes.
In T3 Spec Lines, Toyota GR Cup (2022-), classify as follows:
A specification table follows in the original; it is not shown here.
T3 2016+ Camaro 1LE - Max Wheel Diameter
#34003 from Nicolas Hammann · Rule change · TB 23-06 (2023-05 Fastrack)
fasterT3 Camaro V6 1LE and LT-I4 Turbo 1LE max wheel diameter increases from 18 to 20 inches.
In T3 Spec Lines, Chevrolet Camaro V6 1LE (2016-), change Max. Wheel Size as follows: "18 x 10 20 x 10" In T3 Spec Lines, Chevrolet Camaro LT-I4 Turbo 1LE (2016-), change Max. Wheel Size as follows: "18 x 10 20 x 10"
GT2 appendix letter #33635
#34206 from Ian Barberi · Rule change · TB 23-06 (2023-07 Fastrack)
neutralGT2 BMW engines: 3.4L 6-cyl at 2575 lbs, 4.0L V8 at 2900 lbs, 4.5L V8 at 2950 lbs, 5.0L V8 at 3000 lbs; S54 with 97mm stroke permitted at 2800 lbs.
In GT2-ST Spec Lines, BMW E46 M3 & E36 / BMW Z3 / BMW 5000cc V8, change notes as follows: "The 3.4 liter 6 cyl. (87.0 bore x 93.0 stroke) is permitted at 2575lbs. 4.0L V8 permitted at 2900lbs. 4.5L V8 permitted at 2950lbs. 5.0L V8 permitted at 3000lbs. Flossman body kit permitted as found at http://www.racingpartsbmw.de/start/eng/start.htm. Trans Am SGT spec: Regular shifter 3000 lbs., paddle shifter plus 150 lbs. 95mm S54 crankshaft @ +150lbs. Lang Racing part# S54-95mm-StrokerCrk. S54 engine is permitted a 97mm stroke crankshaft (part #VAC-SC-S54) @2800lbs."
GT2 Remove Weight and Restrictor Penalty for Corvette C7 Body
#34342 from Jorge A Nazario · Rule change · TB 23-06 (2023-07 Fastrack)
fasterGT2 Corvette C7 restrictor increases from 73mm to 77mm flat plate, removing weight penalty.
In GT2/ST, Chevrolet Corvette (2014-2019) change as follows: Restrictor: "73 7mm flat plate"
T3 2022 Toyota GR Cup for T3
#34448 from Club Racing Board · Rule change · TB 23-06 (2023-05 Fastrack)
neutralT3 removes Toyota 2022-up GR Cup and 2022-up GR86 Cup entirely from Spec Lines.
In T3 Spec Lines, remove Toyota 2022-up GR Cup in its entirety. In T3 Spec Lines, remove Toyota 2022-up GR86 Cup in its entirety.
STU 2022 Toyota GR Cup for STU
#34449 from Club Racing Board · Rule change · TB 23-06 (2023-05 Fastrack)
neutralToyota GR Cup and GR86 Cup (2022-) newly classified in STU at 2700 lbs with 2387 cc engine.
In STU Spec Lines, Toyota GR Cup (2022-), classify as follows:
A specification table follows in the original; it is not shown here.
T3 Rules Clarification for Mazda RX8 Spec Line
#34395 from Colin Koehler · Rule change · TB 23-08 (2023-08 Fastrack)
neutralT3 Mazda RX-8 removes transmission/final drive pairing requirement; T4 removes same requirement, adds Mazdaspeed radiator and coil spring kit.
In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows: "Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3 transmission must be paired with the listed alternate final drive. Front sway bar permitted 32mm MAX rear sway bar 19 MAX, Front springs max 750, 500 rear. Cold air intake permitted. Header permitted. Aftermarket flywheel and single disc clutch permitted with no weight penalty." In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows: "Mazdaspeed radiator #0000-01-8501 allowed. Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3 transmission must be paired with the listed alternate final drive. Mazdaspeed coil spring kit #QSEA-34-01Z allowed. 60mm flat plate restrictor required. OE Rear spoiler allowed #F151-V4-920F. OE front air dam allowed #F151-V4-900f-BB. Springs Allowed:
Show 2 more lines
(F) Mazda Motorsports- 0000- 04-9700-08 or Eibach- 0800.250.0700 (R) Mazda Motorsports- 0000-04-9400-07 or Eibach 0700.250.0400, and helper 0000-04-9926 allowed. Alternate sway bars allowed max 32mm (f) 19mm (r)."
T3 2012-2013 Golf R - added to T3
#34413 from Allen Briere · Rule change · TB 23-08 (2023-05 Fastrack)
neutral2012-2013 Volkswagen Golf R added to T3 as new entry with 1984cc engine, 3080 lbs DSG/3050 STD, 36mm turbo inlet restrictor.
In T3 Spec Lines, Volkswagen Golf R (12-13), classify as follows:
A specification table follows in the original; it is not shown here.
T3 rule book corrections
#34437 from Chi Ho · Rule change · TB 23-08 (2023-08 Fastrack)
fasterT3 BMW 320i (14-15) gains aftermarket intercooler permission; T4 loses it.
In T3 Spec Lines, BMW 320i (14-15), add to Notes the following: "Aftermarket intercooler permitted." In T4 Spec Lines, BMW 320i (14-15), remove from Notes the following: "Aftermarket intercooler permitted."
T3 Allowing 255 Tire Width for Nissan 350z
#34471 from Patrick price · Rule change · TB 23-08 (2023-08 Fastrack)
fasterT3 Nissan 350Z and 370Z maximum tire width increases from 245 to 255.
In T3 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo (03-08), change Tire Size (max) as follows: "245 255" In T3 Spec Lines, Nissan 370Z (09-16) / 370Z NISMO Edition (09-13), change Tire Size (max) as follows: "245 255"
T3 Ride Height Correction for the T3 Solstice.
#34615 from Joe Aquilante · Rule change · TB 23-08 (2023-08 Fastrack)
neutralT3 Pontiac Solstice GXP minimum ride height set to 3 inches.
In T2 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following: "Minimum ride height is 3 inches." In T3 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following: "Minimum ride height is 3 inches."
GT2 GT2 Mazda 20B 3 rotor ENO
#34765 from Grand Touring Committee · Rule change · TB 23-09 (2023-09 Fastrack)
fasterGT2 Mazda 20B 3 rotor loses 220 lbs, to 2280, consolidating two spec lines.
In GT2 Spec Lines, Engines - MAZDA, combine both 20B to one spec lines and keep the following: Weight: "2500 2280" Notes: "Must run +100 lbs. for Grand Am transaxle and independent rear suspension. Must comply with all other GT2 rules."
GT2 Late E & O
#34966 from Scotty B White · Rule change · TB 23-10 (2023-10 Fastrack)
fasterGT2-ST Dodge Viper including Comp Coupe, ACR/ACR-X with VRL front fascia loses 100 lbs.
RM 23-10 GT2-ST Dodge Viper, incl Comp Coupe, ACR/ACR-X VRL Front Fascia As an Errors and omissions fix to what was originally intended for these cars, the Club Racing Board and Board of Directors have approved the following: In GT2-ST, Dodge Viper, incl Comp Coupe, ACR/ACR-X add VRL front fascia -100lbs to all Spec Lines.
T3 2006-10 Volkswagen GTI - Weight Reduction request and KO4 Turbo
#34414 from Allen Briere · Rule change · TB 23-12 (2023-12 Fastrack)
fasterT3 Volkswagen GTI 06-10 turbo inlet restrictor increases from 36mm to 37mm.
In T3 Spec Lines, Volkswagen GTI, Jetta GLI (06-10), change Notes as follows: "Turbo Inlet Restrictor 36mm 37mm"
GT2 Errors in GTCS Headings and Use of the Terms Category and ClassChange existing GTL and GTA Rules
#34453 from David Gomberg · Rule change · TB 23-12 (2023-12 Fastrack)
neutralGTL spec lines moved to contiguous position with GT2 and GT3; GTA category and spec lines renumbered and moved behind GTL.
from the current (or before) Table of Contents (TOC), to what is shown in the after TOC. GTL spec lines will now be contiguous with GT2 and 3 spec lines. GTA category and spec lines will be moved and renumbered behind GTL. GTA Section will not change but page numbers will, (as shown in Red italics). 9.1.2.F. GT-2, 3, LITE Category Specifications 314 GT2 Cars 327 GT2/ST 341 GT3 Cars 348
fasterT3 Porsche Cayman (09-12) and (13-16) gear and final drive ratios adjusted; 09-12 6-SPD final drive 3.88 to 3.875, PDK 3.909 to 3.250; 13-16 6-SPD final drive 3.89 unchanged, PDK 3.91 to 3.250.
In T3 Spec Lines, change gear ratios and final drive ratios as follows:
A specification table follows in the original; it is not shown here.
T3 TIR location requirement in VW Golf Spec lines
#35048 from Allen Briere · Rule change · TB 23-12 (2023-12 Fastrack)
neutralT3 VW Golf GTI and Golf R TIR location clarified to maximum 60mm from impeller.
In T3 Spec Lines, Volkswagen GTI (2013), change Notes as follows: "Rear sway bar max 42 mm (body and suspension mounting same as OEM), Any spring up to a maximum spring rate of 800 pounds may be used. Turbo Inlet Restrictor 36mm required max 60mm from impeller. R32 model brake package allowed. Verkline WAS-048 camber arms permitted." In T3 Spec Lines, Volkswagen Golf R (15-16) change Notes as follows: "Max spring rate 800 F&R, Max swaybar 38mm F, 42mm R. 36mm TIR required max 60mm from impeller."
T3 T3 Solstice Brakes
#35106 from Joe Aquilante · Rule change · TB 24-01 (2024-01 Fastrack)
slowerT3 Pontiac Solstice GXP front brake rotor increases from 296 to 355 mm vented.
In T3 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), change Brakes as follows: "(F) 355 296 Vented (R) 270 Solid"
slowerT3 Nissan 350Z DE motor loses 75 lbs to 3125; HR motor gains 47mm restrictors, up from 44mm.
In T3 Spec Lines, Nissan 350ZTrack/ Touring/Standard/Nismo(03-08), change as follows: Weight: "DE Motor: 3200 3125 HR Motor: 3275" Notes: "HR Engine: Two 44mm 47 mm flat plate restrictors required. DE engine: Cold air intake permitted."
GT2 Dodge Viper Gen 3 hybrid Kit Update Request
#35200 from Sean McCann · Rule change · TB 24-01 (2024-01 Fastrack)
slowerGT2-ST Dodge Viper hybrid kit restrictor reduced from 50mm to 45mm flat plates.
In GT2-ST Spec Lines, Dodge Viper, incl Comp Coupe, ACR/ ACR-X change NOTES as follows: 8300 OEM: "Stock OEM engine. Engine long block, valve train, and intake system must meet stock, shop manual specifications. Hybrid update including Mopar Performance Part #P5156137. May use Mopar part #5038554AF (Gen 5 Intake Manifold manifold allowed with (2) 55mm flat plates) and 8.4L mechanical throttle body allowed. VRL Front Fascia -100lbs." 8300: "Hybrid update including Mopar Performance Part # P5156137, Mopar part #5038554AF manifold and 8.4L mechanical throttle body allowed using (2) 50 45mm flat plate restrictors. VRL Front Fascia –100lbs." 8400: "Intake and Throttle Body from Mopar Performance Part # P5156137allowed using (2) 50 45mm flat plate restrictors. , Mopar part #5038554AF manifold (Gen 5 Intake Manifold allowed with (2) 50mm flat plates) VRL Front Fascia -
Show 1 more lines
100lbs 8400 OEM 3225 Stock OEM engine. Engine long block."
T3 Requested Update of Model Years of 370Z
#35231 from Richard Kulach · Rule change · TB 24-01 (2024-01 Fastrack)
neutralT3 Nissan 370Z model years expanded to include NISMO Edition through 2022.
In T3 Spec Lines, Nissan 370Z (09-16) / 370Z NISMO Edition (09-13), change model as follows: "Nissan 370Z (09-16) / 370Z NISMO Edition (09-13) ,incl. Nismo (2009-2022)"
T3 Update Request for 2010 Mustang GT 4.6
#35234 from David Woodle · Rule change · TB 24-01 (2024-01 Fastrack)
neutralT3 2010 Mustang GT 4.6 now allows 2013-14 GT style front/rear fascia, hood, and associated assemblies.
In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), add to Notes the following: "2010 models may update the front and rear fascia, hood and associated assemblies to the 2013-14 GT style."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 SE46 Continued Parity/ Cold Air Intake request
#35267 from Christopher DeShong · Rule change · TB 24-01 (2024-01 Fastrack)
fasterT3 BMW SpecE46 minimum weight drops 50 lbs to 2850.
In T3 Spec Lines, BMW SpecE46, change as follows: Min Weight: "2900 2850" Notes: "Must conform to all SpecE46 rules Version 2.10. SpecE46 spec tire permitted or any DOT permitted up to 225 permitted. No other touring allowances permitted. Engines may not be modified unless specified in the Spec E46 rules and must conform to touring tech procedures. Driver must possess a current copy of the rules. Dyno results do not ensure engine compliance. SE46 HP limit does not apply."
T3 Please help the Subaru STIs.
#35278 from Jared Lendrum · Rule change · TB 24-01 (2024-01 Fastrack)
slowerT3 Subaru STI (15-20) minimum weight increases 100 lbs to 3450; all three STI variants get larger turbo inlet restrictors.
In T3 Spec Lines, Subaru WRX STI (03-07), change Notes as follows: "Killer B intake pipe #EJTI and coupler permitted. 37mm 39mm TIR required." In T3 Spec Lines, Subaru STI (15-20), change as follows: Min Weight: "3350 3450" Notes: "Killer B intake pipe #EJTI and coupler permitted. 37mm 40mm TIR required." In T3 Spec Lines, Subaru Legacy GT/Spec B (05-09), change Notes as follows: "Killer B intake pipe #EJTI and coupler permitted. 37mm 39mm Turbo inlet restrictor required."
STU ST Electric-Assisted Steering Systems
#35066 from Jose Osiris Pena · Rule change · TB 24-02 (2024-01 Fastrack)
neutralSTL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems.
In GCR, Section 9.1.4.M.16., change as follows: "Power steering may be modified in any of the following ways: a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be modified internally to work without pump. b. an OEM manual steering rack for that model may be fitted c. an electric power steering pump may be fitted d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used e. an OEM hydraulic-assisted steering system may be used"
T3 15-18 Golf R Alignment with Existing GTI and R Speclines
fasterGT1, GT2, GT3, GTL, GTX rear spoiler maximum surface area limit of 295.0 square inches removed.
In GCR Section 9.1.2.G (GTA Category Specifications), change as follows: “9.1.2.G.III.I The single-plane rear spoiler must be mounted at an angel angle from 50 to 75 degrees (perpendicular to the ground being 90 degrees) and may not extend beyond the rear bumper when viewed from directly above the rear bumper. Spoilers must be a minimum of .063 aluminum or Lexan and may vary in overall height to match the contours of the bodywork. The rear spoiler dimensions shall not exceed 59.0 inches wide by 5.0 inches in height, (measured on the material surface) , or 295.0 square inches total surface area. Braces to prevent spoiler deflection are allowed, but may serve no other purpose.”
T3 More Car Lightening Stuff
#35319 from Scotty B White · Rule change · TB 24-02 (2024-02 Fastrack)
In GCR, Section 9.1.9.2.D.1.g.3., change as follows: "Batteries may be replaced provided the replacement is capable of starting the car. Batteries may not be relocated unless noted on the spec line. Batteries must be adequately secured. Battery labeling must conform to 9.3.35.D. with those of an alternate manufacturer, provided they are of similar amp-hour capacity, size and within 10% of OEM weight."
T3 Open Strut Tower Brace Options for Ford Mustang V6 (11-14)
#35322 from James Stacey · Rule change · TB 24-02 (2024-02 Fastrack)
neutralT3 Ford Mustang V6 (11-14) gains approved strut tower brace and sway bar kit options.
In T3 Spec Line, Ford Mustang V6 (2011-2014), add to Notes as follows: "Strut Tower Brace #M20201-F, Sway bar Kit #M-5490 or #AR3Z-16A200-A,"
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
neutralT4 now permits C-Spec cars to compete alongside B-Spec cars.
In GCR, Section 9.1.9.2., change as follows: "Touring car eligibility: Cars are eligible for the class they are listed with a specification line and with the specific allowances permitted. In addition, T2-T4 cars may race one class up in touring classes above their specification line class as long as they are a legal T2-T4 car and conform to their specification line allowances as classified. Cars conforming to C-Spec rules are permitted to compete in Touring 4."
neutralT2-T4 spec lines for 46 cars expire 12/31/24; appeal required to continue.
In T2-T4 Spec Lines, add **This Spec line will expire 12/31/24, Please submit to appeal** to Notes to the following Spec Lines: T2: Acura TL SHAWD (10-13) Audi S4 (12-14) Audi S5 (13-14) Audi TT RS (2018-) Cadillac ATS-V (16-17)
Show 46 more lines
Cadillac CTS-V (06-07) Chevrolet Camaro SS (98-02) Honda Civic (2017-) Saturn Sky / Convertible (07-09) Subaru Impreza WRX STi (03-07) Subaru Impreza WRX STi (08-11) T3: Audi S4 (10-11) Audi S4 (12-14) Audi TTS Coupe (10-11) Cadillac ATS (2015) Chevrolet Cobalt (05-07) Dodge SRT-4 (03-05) Ford Fiesta ST (2014-) Hyundai Genesis Coupe (2010-) Hyundai Veloster Turbo (18-21) Mazda RX-8 Base/R3/Sport/ GT (04-12) Mini Cooper S (2016-) Subaru WRX (02-05) Toyota Camry (11-15) T4: Acura Integra GS-R VTEC (3 or 4 door) (94-01) Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05) BMW 320i (14-15) Chevrolet Cobalt SS, Sport Coupe (06-10) Chevrolet Sonic RS (2011-) Chrysler/Dodge Neon ACR SOHC (4 door) (01-02) Dodge Dart (14-15) Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99) Fiat 500 Abarth (12-14) Ford Focus SVT (02-04) Ford Focus ZX4 ST (05-06) Ford Focus (08-11) Ford Mustang V-6 (01-04) Honda Accord LX & EX (03-07) Honda Accord LX-S/EX/EX-L (08-12) Honda Civic Coupe Si (99-00) Honda Civic SI (02-03) Hyundai Elantra GLS (11-12) Hyundai Tiburon V-6 (03-08) Hyundai Veloster Turbo/ R-Spec (14-15) Kia Forte Koup and Sedan LX/EX (10-13) Kia Forte Koup and Sedan SX (10-13) Kia Forte Koup (14-15) Mazda Protégé ES (2000) Mazda Protégé 5 (02-03)
GT2 REDUCE C6 CORVETTE WEIGHT WITH OEM 7 LITER ENGINE REDUCE BY 150LB
#35385 from Mike McGinley · Rule change · TB 24-02 (2024-02 Fastrack)
fasterGT2 Chevrolet Corvette 7011 OEM 7 liter weight reduced 150 lbs, to 3125 lbs.
In GT2/ST Chevrolet Corvette 7011 OEM change weight as follows: “3275 3125“
GT2 GT Direct Injection allowance and rules
#35437 from Grand Touring Committee · Rule change · TB 24-02 (2024-01 Fastrack)
fasterGT1/GT2/GT3/GTL/GTX Direct Injection now permitted if OE, using only OE pump, hoses, injectors.
In GCR, Section 9.1.2.F.7.5.E. change as follows: “Direct Injection is not permitted only if it came OE and must be installed using only OE high pressure pump(s), hard and soft hoses and injectors.”
GT2 GT2/3 remove Direction Injection not allowed in Spec line notes
#35439 from Grand Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)
fasterGT2/3 Nissan, Mazda, Mitsubishi 4G93, QR25DE/DD, QE25DE/DD Direct Injection now permitted per 9.1.2.F.7.5.E.
In GT2/3 modify Spec Line notes as follows: GT2: Nissan: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” GT3: Mazda: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” Mitsubishi 4G93: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E. ” Nissan QR25DE/DD 1988cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” Nissan QE25DE/DD 2489cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.”
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
GT2 Classify Corvette C8 (2020- ) into GT2/ST
#33759 from Andrew Aquilante · Rule change · TB 24-03 (2024-03 Fastrack)
neutralChevrolet Corvette C8 (2020–) classified into GT2-ST with 6162cc displacement, 3300 lbs minimum weight, 71mm restrictor.
In GT2 Spec Lines, classify Chevrolet Corvette C8 (20-) as follows: GT2-ST Maximum Displacement Minimum Weight Restrictor Notes Chevrolet Corvette C8 (20-) 6162 3300 71mm - Flat Plate LT2 engine.
Applies to Chevrolet Corvette on this page: Igor Lyustin
fasterT3 Spec Z 350Z rear wheel width increases to 10 inches; HR Engine restrictors change from 42mm to 44mm.
In T3 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo Spec Z (03-08), change as follows: Max Wheel Size (inch): "18 x 9 (F) 18 x 10 (R)" Notes: "Nissan Motorsports: Shock Front left P/N E6110-SZ350 & Front right E6111- SZ350 & rear E6210-SZ350, springs front P/N 54010-SZ350 & rear 55020- SZ350, F&R 5600S-SZ350, Front sway bar max 37mm. Rear sway bar max 25mm, Bushings P/N (54541, 54560, 55045, 55148, 55149, 55152, 55153, 55158, 56218) - RRZ30 allowed. Nismo flywheel permitted. SPC Control Arms 72125 and 72123 are allowed. HR Engine: Two 42mm flat plate restrictors required. Zspeed and Z1 alternative clutch slave permitted. Must conform to all SpecZ 2018 Edition rules. No other touring allowances beyond 2018 SpecZ edition rules or allowances listed here. Nissan brake part numbers NISMO Race Front Caliper Kit 41001-FR350, NISMO Front Rotor-RIGHT 40206-
Show 3 more lines
SZ350, NISMO Front Rotor-LEFT 40207-SZ350 permitted. 44011-RC350 rear caliper kit permitted, 43206-SZ350 Right rotor permitted, 43207-SZ350 Left rotor permitted. Car must conform to the Official 2024 Spec Z Rules. HR Engine: Two 44mm flat plate restrictors required. Tires must conform to Spec Z rules. Competitor must be able to provide a copy of the current rules."
In T2-T4 Spec Lines, change Spec Line as follows: "Wheel- base (mm) Required Restrictor"
GT2 Requesting classification for a 2015 Mitjet ST in GT2
#35408 from Jim Froula · Rule change · TB 24-03 (2024-03 Fastrack)
neutral2015 Mitjet ST added to GT2, must run per VTS specifications with complete FIA form CdM008.
In GT2 Spec Lines, GT Cars - MITJET ST, classify MITJET ST as follows: GT Cars – MITJET ST Model Years Body Style Drive- line Wheel- base (in) Notes MITJET ST 2015 RWD 94.5 Must run per VTS specifications. Must have
Show 2 more lines
complete car Specifications (FIA form CdM008) at every entered race event.
neutralSTU Mini Cooper S SC: alternate LEAP OMICRON hood scoop LEP-OMICRON3 permitted.
In STU Spec Lines, Mini Cooper S SC with Minimum Weight 1900 and 2100, add to Notes: "Alternate LEAP OMICRON hood scoop part # LEP-OMICRON3 is permitted."
neutralT3 Nissan 350Z and 370Z now allow brake booster vacuum regulator, must not be in-car adjustable.
In T3 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo (03-08), add to Notes as follows: "Brake booster vacuum regulator allowed, cannot be in-car adjustable." In T3 Spec Lines, Nissan 370Z, incl. Nismo (2009-2022), add to Notes the following: "Brake booster vacuum regulator allowed, cannot be in-car adjustable."
Applies to Nissan 370Z on this page: Gamaliel Aguilar-Gamez
T3 Mustang Help
#35559 from Ross Murray · Rule change · TB 24-03 (2024-03 Fastrack)
fasterT3 Ford Mustang 4.6L restrictor holes increased from 40 mm to 45 mm.
In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), change Notes as follows: "A flat plate restrictor with two 40 mm 45mm holes required directly behind throttle body."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 Appeal for Retention of T3 Mazda RX-8 Spec Line (Letter #35378)
#35577 from Raymond Blethen · Rule change · TB 24-03 (2024-03 Fastrack)
unclearT3 Mazda RX-8 Spec Line retention appeal directed to letter #35584 for ruling.
Thank you for your letter. Please see letter #35584 in current Fastrack.
slowerGT2-ST Acura NSX minimum weight raised to 3000 lbs, restrictor increased to 45mm TIR.
In GT2-ST Spec Lines, Acura NSX, change as follows: Minimum Weight: "2700 3000" Restrictor: "43 45mm TIR"
T3 Allow T4 and T3 RX8 to Disable/Remove Factory Oil Inj.
#35761 from David Mead · Rule change · TB 24-05 (2024-05 Fastrack)
unclearT3 and T4 Mazda RX-8 may remove or disable factory oil injection system.
In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows: "OEM oil injection system may be removed or disabled." In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows: "OEM oil injection system may be removed or disabled."
GT2 Request to Eliminate the FPR from the Corvette (-2013) with LS2
#35878 from Michael Quattlebaum · Rule change · TB 24-05 (2024-05 Fastrack)
fasterGT2-ST Corvette 14-19 LS2 restrictor increases from 78mm to 80mm flat plate.
In GT2-ST Spec Lines, Chevrolet Corvette (14-19), change Restrictor as follows: "78 80mm flat plate"
T3 Driveshafts
#35916 from Scotty B White · Rule change · TB 24-05 (2024-05 Fastrack)
slowerT2, T3, T4 driveshafts may use alternative materials or one-piece units; non-OEM adds 25 lbs.
In GCR Section 9.1.9.2.D.4.b., add the following: "6. T2-T3- Driveshafts may be replaced with alternative materials ie. carbon fiber, aluminum, steel. Two-piece driveshafts may be replaced with one-piece units. If non-OEM driveshaft is used, add 25 lbs."
neutralAudi S4 00-02 in T3 must compete in 3 Super Tour events before Runoffs eligibility.
In T3 Spec Lines, Audi S4 (00-02), add to Notes as follows: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
unclearT3 Mazda MX-5 Global Cup Miata ND1/ND2 tire size changes to 225 DOT specification.
In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND2, change Tire Size as follows: "Series Mazda MX5 Cup spec tires: 215/610 R17 BF Goodrich G-Force Slick, 20/61- 17 G-Force Wet-P2G or 225 DOT"
T3 Mustang T2/T3
#35877 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)
unclearFord Mustang GT 5.0L and V6 now permit Track/Performance Package parts in T2 and T3.
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes as follows: "Track/Performance Package parts permitted." In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows: "Track/Performance Package parts permitted." In T3 Spec Lines, Ford Mustang V6 (15-17), change Notes as follows: "Track/Performance package allowed."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 T2-T4 Driveshaft Mistake...?
#36050 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)
fasterT2-T4 Ford Mustangs: remove 25 lbs penalty for non-OEM driveshaft, clarify alternate driveshaft allowances.
In GCR Section 9.1.9.2.D.4.b.6., remove as follows: "If non-OEM driveshaft is used, add 25 lbs." In T2 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows: "Driveshaft from Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang Boss 302 (12-13), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang GT 5.0L (11-14)ki, change Notes as follows: "Alternate metallic driveshaft is allowed."
Show 12 more lines
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L (05-10), change Notes as follows: 'An Aluminum driveshaft is allowed." "Alternate metallic driveshaft is allowed." In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), change Notes as follows: "An Aluminum driveshaft is allowed." "Alternate metallic driveshaft is allowed." In T3 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows: "Driveshaft from Alternate metallic driveshaft is allowed."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
neutralGT2-ST allows aftermarket replacement differential housings if exact equivalents.
In GCR Section, Appendix K. 2012.M2, add the following: "After market replacement differential housings are permitted as long as they are an exact equivalent."
fasterT3 Nissan 350Z DE engine now permits cold air intake.
In T3 Spec Lines, Nissan 350ZTrack/ Touring/Standard/Nismo(03-08), add to Notes as follows: "DE engine: Cold air intake permitted."
T3 B8/8.5 Audi S4 T3 and T2
#36195 from Brian Leib · Rule change · TB 24-07 (2024-07 Fastrack)
neutralAudi S4 (2000-2002) moves to T3 with 3400 lbs minimum weight, 38mm turbo inlet restrictor required.
In T3 Spec Lines, Classify Audi S4 (2000-2002) as follows and allow the T2 spec line to expire.
A specification table follows in the original; it is not shown here.
T3 Z4 Roadster Eligibility
#36196 from Allan Unruh · Rule change · TB 24-07 (2024-07 Fastrack)
neutralT3 BMW Z4 3.0si expands to include 3.0i Roadster and Coupe (07-08); hardtop permitted with positive fasteners.
In T3 Spec Lines, BMW Z4 3.0si, & Coupe (07-08) change Model and add to Notes as follows: "BMW Z4 3.0si, 3.0i, Roadster & Coupe (07-08)" Notes: "Any OEM or aftermarket hardtop permitted that retains the OEM roof silhouette (if a hardtop is used, latches shall be replaced with positive fasteners)."
GT2 GT4 cars may run in GT2-ST
#36235 from Grand Touring Committee · Rule change · TB 24-07 (2024-07 Fastrack)
neutralGT4 cars now permitted in GT2-ST with factory restrictor, must comply with 2012 STO rules, slicks allowed with 100-pound penalty.
In 9.1.2. GT2 Spec Lines, GT3 Cars, change Note as follows: "Note: All GT4 cars are permitted to compete in GT2-ST provided they use a factory supplied power stick or Pro Series required restrictor. Must have GT4 rules in possession at all race events. Cars must comply with 2012 STO rules as stated in Appendix K of the GCR. Engine Displacements in this table are nominal. Each competitor shall have available definitive documentation (e.g., factory manual) of the original displacement for the engine used. Slicks allowed on all GT2/ST cars with a 100-pound weight penalty."
T3 Honda Civic Si (2017+)
#36249 from Jason LaManna · Rule change · TB 24-08 (2024-08 Fastrack)
fasterT3 Honda Civic Si (2017-2021) restrictor removed, weight to 2950 lbs, Runoffs eligibility requires 3 Super Tour events.
In T3 Spec Lines, Honda Civic Si (2017-) with 2900 weight, change as follows: Model: "Honda Civic Si (2017-2021)" Restrictor: "36mm TIR" Add to Notes: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**" In T3 Spec Lines, Honda Civic Si (2017-), change as follows: Model: "Honda Civic Si (2017-2021)" Restrictor: "36mm TIR" Weight (lbs): "30752950"
Show 1 more lines
Add to Notes: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
STU RWD Turbo Disadvantage
#36255 from David Fiorelli · Rule change · TB 24-08 (2024-08 Fastrack)
fasterSTU RWD turbo cars no longer required to reduce restrictor by 1 mm from table.
In GCR, Section 9.1.4.1.H.3 - Inlet Restrictor (mm) Minimum Weight (lbs) table, change as follows: "RWD cars must reduce restrictor 1 mm from this table"
T3 Subaru Reliability Help
#36284 from Anthony Piselli III · Rule change · TB 24-08 (2024-08 Fastrack)
neutralT3 Subaru STI (15-20) and WRX STI (03-07) permitted to use OEM spec block #IAG-ENG-S550 and head studs.
In T3 Spec Lines, Subaru STI (15-20), add to Notes the following: "OEM spec block permitted # IAG-ENG-S550, Head studs permitted." In T3 Spec Lines, Subaru WRX STI (03-07), add to Notes the following: "OEM spec block permitted # IAG-ENG-S550, Head studs permitted."
slowerSTU Mini Cooper S SC 1900 restricts to 2.565 diameter pulley; 2100 allows 2.285 diameter pulley.
In STU Spec Lines, Mini Cooper S SC, add to notes: 1900: "Stock supercharger pulley. 2.565 diameter." 2100: "JCW Pulley permitted. May run a 2.285 diameter pulley."
neutralT3 VW Golf R (12-13 and 15-18) 36mm TIR placement now allows OEM turbo inlet, removing 60mm distance limit from impeller.
In T3 Spec Lines, Volkswagen Golf R (12-13), change Restrictor Required as follows: "36mm TIR max 60mm from impeller TIR may be placed in the OEM turbo inlet as long as the restriction is entirely within the leading edge of the housing." In T3 Spec Lines, Volkswagen Golf R (15-18), change Restrictor Required as follows: "36mm TIR max 60mm from impeller TIR may be placed in the OEM turbo inlet as long as the restriction is entirely within the leading edge of the housing."
T3 Redundant Verbiage Regarding Mustang Spec Lines for Driveshaft
#36484 from David Mead · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT2 and T3 Mustang spec lines remove redundant driveshaft alternate/aluminum allowance wording.
In T2 Spec Lines, change Notes as follows: Ford Mustang V6 (11-14): "Alternate driveshaft is allowed." Ford Mustang Boss 302 (12-13): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (11-14): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (15-17): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (2018-): "Alternate driveshaft is allowed. Springs up to 800#/in front and rear permitted. Alternate metallic driveshaft permitted." Ford Mustang Coupe GT & Shelby GT 4.6L (05-10): "Alternate driveshaft is allowed."
Show 4 more lines
In T3 Spec Lines, change Notes as follows: Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10): "Alternate driveshaft is allowed." Ford Mustang V6 (11-14): "Alternate driveshaft is allowed." Ford Mustang V6 (05-10): "An Aluminum driveshaft is allowed."
neutralT2, T3, T4 fuel cell installations may remove charcoal canisters, emissions valves, and sensors.
In GCR, Section 9.1.9.2.D.1.c. add the following: "5. Removal of ancillary fuel tank equipment charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket fuel cell installations."
neutralT2, T3, T4 brake component wording clarified: 2-piece rotors allowed in T2 within 5% OE diameter, T3 within 2% OEM diameter.
In GCR, Section, 9.1.9.2.D.6. Brakes, change as follows: "a. Components 1. The make and material of brake pads and linings may be changed. 2. Brake fluid may be substituted with any brake fluid. 3. Brake rotor dust shields may be removed or replaced to accommodate brake ducts. 4. Flexible rubber brake lines may be replaced with Teflon lined, metal braided hoses. 5. Any brake ducts are permitted, but they must serve no other purpose. Fender liners may be modified solely for routing and attachment of brake ducts. Duct intake openings may be created by the opening of 2 sections up to 14.5 square inches each in
Show 10 more lines
the front fascia. The stock headlamp location is not permitted for brake ducting. Two alternative duct openings may be created by the removal of the fog lights or 2 sections up to 14.5 square inches each of stock false grills originally located in the front fascia. 6. Stock replacement brake rotors may be obtained from sources other than the manufacturer provided they are the exact equivalent of the stock rotors. In T2 only - 2-piece rotors with ferrous metal rotor disks and aluminum hats are allowed, must be within 5% of OE diameter. In T3 only - 2-piece front rotors with ferrous metal rotor disks and aluminum hats are allowed, must be within 2% of OEM diameter. Drilled and slotted rotors are permitted. 7. Parking brakes, mechanisms, and actuating components may be removed. 8. Brake vacuum reservoirs sized 0.50 gallons or smaller are permitted. The port or fitting at the vacuum source may not be modified, enlarged or relocated. The vacuum reservoir and brake booster must be a closed system."
neutralT2, T3, T4 fuel cell cars may remove charcoal canisters, emissions valves, and sensors.
In GCR, Section, 9.1.9.2.D.1.c., add the following: "5. Removal of ancillary fuel tank equipment; charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket fuel cell installations."
STU Request to Remove Miata Hubs from General category
#37138 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)
neutralSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
In GCR, Section 9.1.4.M.18., change as follows: "18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."
T3 Allow Spec MX5 upgrade kit for 2009-11 RX8 S2 Transmision
#37140 from Chris Braunlich · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT3 and T4 Mazda RX-8 and MX-5 permit transmission kit #0000-02-5700.
In T4 Spec Lines, add the following to Notes: Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted. Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted." In T3 Spec Lines, add the following to Notes: Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted." Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted."
STU BMW N54/N55 Engine Allowance
#37146 from Martin Sarukhanyan · Rule change · TB 24-12 (2024-12 Fastrack)
slowerSTU BMW N54/N55 turbo inlet restrictors now required per GCR definition; turbo swapping prohibited.
"Turbo inlet restrictors designed per GCR Appendix F Technical Glossary definition of “Turbo Inlet Restrictor” may be required; see table 9.1.4.1.H.h.2 3. Swapping of turbochargers between engine makes and models is prohibited. Supercharged cars may be approved on a case-by-case basis; twin turbo engines are allowed on a case-by-case basis only. Contact the Road Racing Technical Office for details. Twin turbo engines may be converted to single turbo using one of the allowed alternate turbos (see 9.1.4.1.H.3 2). Aftermarket turbocharger and supercharger kits will be allowed on a case-by-case basis.
T3 Move Spec Boxster to T4
#37158 from Rob Piekarczyk · Rule change · TB 24-12 (2024-12 Fastrack)
neutralPorsche Spec Boxster moves to T4, minimum weight 2750 lbs, requires 3 Super Tour events before Runoffs eligibility.
In T4 Spec Lines, classify Porsche Spec Boxster, as follows:
A specification table follows in the original; it is not shown here.
T3 BMW 320i Spec Line
#37204 from chi ho · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT4 BMW 320i 14-15 Spec Line expires 12/31/24 removed; Turner Motorsports intercooler #024703TMS02 allowed.
In T4 Spec Lines, BMW 320i (14-15), change Notes as follows: "**This Spec line will expire 12/31/24, Please submit to appeal** Turner Motorsports intercooler #024703TMS02 allowed."
T3 Classification for a 2005 Cadillac CTS 3.6 liter 6 speed manual
fasterT3 Subaru WRX STI 03-07 drops 100 lbs to 3200; Legacy GT/Spec B 05-09 drops 150 lbs to 3200.
In T3 Spec Lines, Subaru WRX STI (03-07), change Weight as follows: "3300 3200" In T3 Spec Lines, Subaru Legacy GT/Spec B (05-09), change Weight as follows: "3350 3200"
STU Audi 1.8t Wagon STU Table B
#36685 from Mike McLaughlin · Rule change · TB 25-01 (2025-01 Fastrack)
fasterSTU Audi 1.8T wagon deleted; Porsche 944 1800 weight to Chart, turbo inlet restrictor removed.
In STU Spec Lines, Table B: Alternate Vehicle and Engine Requirements, delete Audi/VW 1.8 Turbo in its entirety. In STU Spec Lines, Table B: Alternate Vehicle and Engine Requirements, Porsche 944 w/Max Displacement 1800, change as follows: Weight: "3050 Chart" Notes: "VW/Audi 1.8L 35mm turbo engine permittedinlet restrictor required."
GT2 Panoz Esperante GTS BOP
#36686 from Brian Goldburg · Rule change · TB 25-01 (2025-01 Fastrack)
In GT2 SPEC LINES, GT Engines - PANOZ, classify 2013-2016 Ford EcoBoost Twin Turbo as follows: GT Engines – PANOZ Engine Family Engine Type Bore x Stroke (in.) Disp.
Show 2 more lines
(CC) Head Type Valves /
A specification table follows in the original; it is not shown here.
T3 Request to Move Spec Mustang to Touring 3 (from T2)
#37080 from Roger Eagleton · Rule change · TB 25-01 (2025-01 Fastrack)
neutralFord Spec Mustang moves to T3 with 44mm bore restrictor, 275 max tire, 3450 lbs minimum weight.
In T3 Spec Lines, classify Ford Spec Mustang as follows:
A specification table follows in the original; it is not shown here.
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
GT2 Correct language regarding OEM Areo Devices
#37137 from Christopher Childs · Rule change · TB 25-01 (2025-01 Fastrack)
In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows: "B. Aerodynamic Devices 2. Rear wing c. The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule."
A specification table follows in the original; it is not shown here.
T3 3.7 Mustangs BoP
#37186 from Scotty B White · Rule change · TB 25-01 (2025-01 Fastrack)
fasterT3 Ford Mustang V6 (11-14) and (15-17) now permit cold air intake.
In T3 Spec Lines, Ford Mustang V6 (11-14), add to Notes the following: "Cold air intake permitted." In T3 Spec Lines, Ford Mustang V6 (15-17), add to Notes the following: "Cold air intake permitted."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
GT2 GT2 Sunbeam Tiger Alternate Carburetor
#37198 from Tom Patton · Rule change · TB 25-01 (2025-01 Fastrack)
In T2, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Acura TL SHAWD (10-13) Audi S4 (12-14) Audi S5 (13-14) Audi TT RS (2018-) Cadillac ATS-V (16-17) Cadillac CTS-V (06-07) Chevrolet Camaro SS (98-02)
Show 49 more lines
Honda Civic Type-R (2017-) Saturn Sky / Convertible (07-09)" In T3, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Audi TTS Coupe (10-11) Cadillac ATS (2015) Chevrolet Cobalt (05-07) Dodge SRT-4 (03-05) Ford Fiesta ST (2014-) Hyundai Genesis Coupe (2010-) Hyundai Veloster Turbo (18-21) Mini Cooper S (2016-) Toyota Camry (11-15)" In T4, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Acura Integra GS-R VTEC (3 or 4 door) (94-01) Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05) Chevrolet Cobalt SS, Sport Coupe (06-10) Chevrolet Sonic RS (2011-) Chrysler/Dodge Neon ACR SOHC (4 door) (01-02) Dodge Dart (14-15) Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99) Fiat 500 Abarth (12-14) Ford Focus SVT (02.5-04) Ford Focus ZX4 ST (05-06) Ford Focus (08-11) Ford Mustang V-6 (01-04) Honda Accord LX & EX (03-07) Honda Accord LX-S/EX/EX-L (08-12) Honda Civic Coupe Si (99-00) Honda Civic SI (02-03) Hyundai Elantra GLS (11-12) Hyundai Tiburon V-6 (03-08) Hyundai Veloster Turbo/ R-Spec (14-15) Kia Forte Koup and Sedan LX/EX (10-13) Kia Forte Koup and Sedan SX (10-13 Kia Forte Koup (14-15) Mazda Protégé ES (2000) Mazda Protégé 5 (02-03) Mazda6 s (03-07) Mitsubishi Eclipse GT (00-05) Nissan Sentra SER (02-03) Pontiac Firebird V-6 (96-02) Scion tC (03-07) Subaru Impreza (non-turbo) (04-06) Toyota Celica GT (00-05) Toyota Celica GTS/GT (00-05) Volkswagen Golf TDI (2010) Volkswagen Passat (12-14) Volkswgen Passat TDI (12-14) Volkswgen Passat 1.8T (2014-)"
STU Merger GT3 to STU
#37486 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)
neutralSTU-GT3 reclassified as STU-GT3U effective January 1, 2026.
In STU, Table C, change STU-GT3 charge as follows: "(Effective January 1, 2026) TABLE C: STU-GT3U"
STU GT3 TCR Tire allowance
#37494 from Club Racing Board · Rule change · TB 25-01 (2025-01 Fastrack)
slowerSTU GT3 TCR gains 275-width tire option with 100 lb weight penalty, but not in A compound.
In STU, Table C, GT3 TCR, add to Notes the following: "May run DOT approved tire with maximum section width of 275 with 100 pound weight adder. May not run A compound with 275."
#36538 from Jorge A Nazario · Rule change · TB 25-02 (2025-02 Fastrack)
fasterGT2 STO aftermarket ABS weight penalty reduced from 100 lbs to 50 lbs.
In GCR, Appendix K. 2012 STO Rules, O.9., change as follows: "May run OEM ABS or convert to an aftermarket ABS controller with 100 50 lb. weight penalty."
fasterT3 Nissan 350Z HR Engine FPR restrictor increases from 47mm to 49mm.
In T3 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo (03-08), change Required Restrictor as follows: "HR Engine: (2) 47mm 49mm FPR"
T3 Request to Classify Club Spec in Appropriate Touring Classes
#37523 from Andrew Benagh · Rule change · TB 25-02 (2025-02 Fastrack)
neutralFord SCCA Club Spec Mustang classified T3 at 3350 lbs with driver; Mazda SCCA Club Spec MX-5 classified T4 at 2500 lbs with driver.
In T3 Spec Lines, classify Ford SCCA Club Spec Mustang (CSM) as follows:
A specification table follows in the original; it is not shown here.
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21
GT2 Hood Bulge allowed
#37000 from Gordon Leslie · Rule change · TB 25-03 (2025-03 Fastrack)
unclearGT2 Pontiac Fiero changes from FWD to RWD; hood bulge permitted for front engine relocation.
In GT2 Spec Lines, GT2 Cars - PONTIAC, Fiero, change as follows: Drive-line: "FWD RWD" Add to Notes: "Hood bulge permitted as requested for front engine relocation only."
STU BMW N54/N55 Engine Allowance Follow Up
#37447 from Martin Sarukhanyan · Rule change · TB 25-03 (2025-03 Fastrack)
neutralSTU BMW N54/N55 3.0L classified at Chart +3% minimum weight; N54 twin turbo not allowed.
In STU Spec Lines, Table A, classify BMW N54/N55 as follows: STU Maximum Displacement (cc's) Minimum Weight Notes BMW N54/N55 3.0 Chart +3% (DI) Short blocks, heads, and intakes may be freely swapped within these engine designations. N54 twin turbo not allowed
GT2 OEM Wing Adjustment
#37590 from Christopher Childs · Rule change · TB 25-03 (2025-03 Fastrack)
slowerTA2 and STO OEM wings no longer exempt from rear wing height rule at roof peak.
In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows: "The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule." In GCR, Section APPENDIX K. 2012 STO GENERAL TECHNICAL REGULATIONS, D.4.b., add the following: "Factory wings, and spoilers, and roof vortex generators are permitted, but must be removed if an approved aftermarket wing is installed. OEM aerodynamic devices do not need to adhere to the height rule."
STU STU Mini Cooper pulley size clarification re: letter #36980
fasterSTU Mini Cooper S SC supercharger pulley diameter reduced from 2.285 to 2.185.
In STU Spec Lines, Mini Cooper S SC, add to notes: 2100: "May run a 2.285 2.185 diameter pulley."
STU Question About a Weight Modifier
#37782 from Peter St Pierre · Rule change · TB 25-03 (2025-03 Fastrack)
fasterSTU Honda K20C1 Turbo I4 exempted from 3% DI weight adder in Spec Lines Table A.
In STU Spec Lines, Table A, Honda K20C1 Turbo I4, add to Notes the following: "The 3% DI weight adder does not need to be applied."
STU Increase Minimum Weight
#37919 from Club Racing Board · Rule change · TB 25-03 (2025-03 Fastrack)
slowerSTU GT3U minimum weight increases 150 to 250 pounds.
In STU Spec Lines, Table C: STU-GT3U, change Minimum Weight as follows: "150 250 pounds"
T3 SpecE46 Tire Change
#37421 from Simon Foweather · Rule change · TB 25-04 (2025-04 Fastrack)
unclearT3 BMW Spec E46 updates to SpecE46 rules Version 1.1 dated Jan. 6, 2025.
In T3 Spec Lines, BMW Spec E46, change Notes as follows: "Must conform to all SpecE46 rules Version 2.10. Version 1.1 dated Jan. 6, 2025."
T3 S197 Mustang V6 in T3
#37594 from John LoGiudice · Rule change · TB 25-04 (2025-04 Fastrack)
fasterT3 Ford Mustang V6 11-14 minimum weight drops 25 lbs to 3325.
In T3 Spec Lines, Ford Mustang V6 (11-14), change Min. Weight as follows: "3350 3325"
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
FE2 Driver Safety & Comfort
#37965 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)
neutralFE2 allows driver safety and comfort modifications for disabled drivers with SCCA approval, not transferable to other drivers.
In FE2, GCR section 9.1.1.G.2.E, add the following: "g. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
STU Wheel Size Inconsistency
#38018 from David Fiorelli · Rule change · TB 25-05 (2025-05 Fastrack)
neutralSTU wheel width rules clarified: cars ≤2,850 lbs max 8 inches, cars >2,850 lbs max 9 inches.
In GCR, Section 9.1.4.1.F.1., change as follows: "Wheels may not exceed 18 inches in diameter. or 8.0 inches in width for vehicles 2950 lbs. and under minimum allowed race weight. Vehicles over 2850 minimum allowed race weight may use a 9 inch wide wheel. Cars equal to or less than 2,850 lbs. minimum allowed race weight may not use wheels wider than 8 inches. Cars greater than 2,850 lbs. minimum allowed race weight may not use wheels wider than 9 inches."
T3 S550 Mustang
#38061 from Scotty B White · Rule change · TB 25-05 (2025-05 Fastrack)
fasterT3 Ford Mustang V6 15-17 weight drops 50 lbs to 3350, brake options clarified with M2300V now 50 lb penalty or Brembo alternative.
In T3 Spec Lines Ford Mustang V6 (15-17), change as follows: Weight: "3400 3350" Notes: "Rear spring relocated to shock allowed. 800lbs springs (F/R) allowed. Track/ Performance Package parts permitted. Optional: 6 speed automatic transmission (with paddle shifters). Sway bars allowed up to 38mm (F) 28mm (R). Ford Motorsports 6-piston M2300V 380mm brake kit allowed with +50lb penalty, or optional 2-piece rotor 355mmmax Brembo brake kit #M- 2300-S allowed. Cold air intake permitted."
unclearT3 BMW Spec E46 rules updated to Version 3.0 from Version 1.1.
In T3 Spec Lines, BMW Spec E46, change Notes as follows: "Must conform to all SpecE46 rules Version 2.10. Version 1.1 dated Jan. 6, 2025. Version 3.0."
STU Table C: STU-GT3U Clarification
#38268 from Club Racing Board · Rule change · TB 25-05 (2025-05 Fastrack)
fasterSTU Spec Line GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tire options clarified with weight adjustments.
In STU Spec Line, Table C: STU-GT3U, change as follows: Minimum Weight: “Current GT3 race weight plus 250 225 pounds” Notes: "DOT approved tire with maximum section width of 245. GT3 cars base wheel is a maximum of 15”x9”. 18”x9” wheels allowd with a 3% weight addition. GT3 cars utilizing 15”x7” wheels are limited to a maximum section width of 225 with a 25 pound weight reduction" "All GT3U (Majors and Runoffs) cars using up to 15"x7" wheels limited to 225 section width tires shall run at current GT3 race weight plus 225lbs. All Gt3U cars shall run a DOT approved tire with a maximum section width of 245. GT3U cars are allowed optional 15"x9" wheels with a 1.5% weight addition or up to 18"x9" wheels with a 3.0% weight addition to the total weight
Show 1 more lines
including the 225 lbs."
STU 2.8-3.2L N/A Engine Allowances
#38007 from Ben Slechta · Rule change · TB 25-07 (2025-07 Fastrack)
unclearSTU 2.8-3.2L N/A engines now allow 245 max tire width; over 3150 lbs may run 275 with 2% weight penalty.
In GCR, Section 9.1.4.G.1, add the following: "A maximum section width of 245 is permitted. Cars over 3150 lbs. may run a 275 tire with a 2% weight adder."
unclearBMW Spec E46 in T3 updates to SpecE46 rules Version 3.0.
In T3 Spec Lines, BMW Spec E46, change Notes as follows: "Must conform to all SpecE46 rules Version 2.10. Version 1.1 dated Jan. 6, 2025. Version 3.0."
STU 2006-2015 Mazda Miata Intake Manifold
#38422 from German Candelario Candelario · Rule change · TB 25-07 (2025-07 Fastrack)
neutralSTU Mazda MZR may use Goodwin 61-2510 or Gato Performance 31972 intake manifold.
In STU, Table A, Mazda MZR (LF, L3, L5), change Notes as follows: "May use Goodwin Part # 61-2510 or Gato Performance Part #31972 Intake manifold . "
STU Requesting Approval of the JDM Honda h23a
#38489 from Eric Fiest · Rule change · TB 25-07 (2025-07 Fastrack)
neutralSTU Honda JDM H23a added, 2259cc displacement, minimum weight per Chart, must meet ST engine regulations.
In STU, Table B, classify Honda JDM H23a as follows: STU Maximum Displacement (cc's) Minimum Weight Notes Honda JDM H23a 2259 Chart Must meet all ST engine regulations.
T3 Incorrect Touring Heading
#38451 from Terry Hanushek · Rule change · TB 25-08 (2025-08 Fastrack)
neutralT2, T3, T4 Spec Lines table header changed from T2 to ET.
In T2-T4 Spec Lines, change Table Header as follows: "T2 ET"
neutralGT2 Porsche 911 Coupe & Targa may use 993 3.8 RSR rear deck lid or approved aftermarket reproductions.
In GT2 Spec Lines, GT2 Cars-Porsche, 911 Coupe & Targa., add to Notes the following: "Porsche 911-based race cars (911,963,994), the use of the 993 3.8 RSR rear deck lid/spoiler is permitted. Aftermarket reproductions of the original Porsche Motorsports deck lid provided they faithfully replicate OEM dimensions and functionality, are acceptable for use."
STU STU-TCR Adjustments
#38723 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)
slowerSTU-TCR tire width increases to 275 with weight adder raised from 100 to 150 pounds.
In STU Spec Lines, Table C: STU-GT3U, GT3-TCR, change as follows: Remove the current TCR spec line and add the TCR spec lines from GT3 that are being removed, adding the below to the notes. "DOT approved tire with maximum section width of 245. May run DOT approved tire with maximum section width of 275 with 100 150 pound weight adder. May not run A-compound with 275. STU-TCR spitters and side valance must comply with 9.1.4.D.3.f. STU-TCR chassis ride height must comply with 9.1.4.1.A.1."
STU Lotus Weight Reduction
#38772 from Club Racing Board · Rule change · TB 25-08 (2025-08 Fastrack)
fasterSTL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs.
In 9.1.2. GT2/ST Spec Lines, Lotus Evora GT4, change Weight as follows: "2750 2700" In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows: Lotus Elise Cup R: "2300 2250" Lotus Elise SC/ Lotus Exige SC: "2300 2550 2500 2450"
STU Lotus Weight Reduction E&O
#38919 from Club Racing Board · Rule change · TB 25-09 (2025-09 Fastrack)
fasterSTU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs.
In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows: Lotus Elise SC/ Lotus Exige SC: "2450 2250"
FE2 FE & FE2 Bubble Tail
#38978 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)
neutralFE and FE2 Enterprises must use bubble tail P/N WM138014; FE2 allows only this configuration.
In FE, GCR section 9.1.1.G.2.F.k, change as follows: "Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."
T3 Make the S2000 Competitive Again
#38470 from David Mead · Rule change · TB 25-08 (2025-08 Fastrack)
fasterT3 Honda S2000 wheels grow to 17x9.0 front and 17x10 rear; tyres widen to 255 front and 275 rear.
In T3 Spec Lines, Honda S2000 (all) (00-09), change as follows: Max Wheel Size: "(Effective 11/1/2025) 17 x 9.0 (f) 17 x 10 (r)" Tire size: "(Effective 11/1/2025) 245 255 (f) 275 (r)" Notes: "(Effective 11/1/2025) CAI allowed, Header allowed."
STU Non-Homologated Engine Swaps - Specifically K24A2 w/ Honda CRZ
#38746 from William Rori · Rule change · TB 25-09 (2025-09 Fastrack)
slowerSTU Honda K24 engine swap weight increases by 2% effective November 1, 2025.
In STU Spec Lines, Table B: Alternate Vehicle and Engine Allowances, Honda K24, change Weight as follows: "(Effective 11/1/2025) Chart + 2%"
T3 ND Gearset Request for T4
#39166 from Josh Smith · Rule change · TB 25-11 (2025-11 Fastrack)
neutralT3 and T4 Mazda MX-5 Miata models add approved gear kit PT#-0000-02-6100 to notes.
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T3 Spec Lines, Mazda MX-5 Miata (16-18), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, add to Notes the following: "Gear kit Kit PT#- 0000-02-6100."
T3 ND Spec Lines Wrong PT#'s
#39170 from Josh Smith · Rule change · TB 25-11 (2025-11 Fastrack)
neutralT4 Mazda MX-5 Miata/Club/RF (19-24) and (16-18) remove discontinued hardtop part #0000-07-5901; T3 MX-5 Miata (16-18) and Global Cup ND (16-21) same.
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must remain stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5804-01). Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs #0000-04-9700-08, springs up to 500lb front and 300lb rear allowed. Mazda tower brace 0000-04-5626 allowed. Mazda header
Show 20 more lines
0000-06-5410 allowed." In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. Up to 500lb front and 300lb rear springs allowed. Mazda Motorsports Header part #0000-06-5410 allowed. Mazda tower brace 0000-04-5626 allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5." In T3 Spec Lines, Mazda MX-5 Miata (16-18), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Header permitted. Cold air intake permitted. Front strut brace permitted. Front and rear sway bars permitted up to 35mm, Springs 800 front and 800 Rear max permitted. Any OEM or aftermarket hardtop permitted that retains the OEM roof silhouette including Mazda hardtop part #0000-07-5902- ND and part #0000-07-5901 (discontinued DG Motorsports top). If a hardtop is used, latches shall be replaced with positive fasteners. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, change Notes as follows: "Shoulder harness installation must conform to FIA mounting specifications that are approved for this vehicle per section 6.2 FIA article 253, safety equipment. Must meet all ND2 MX-5 Global Cup rules. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop Mazda hardtop part #0000-07-5902-ND and #0000-07-5902-ND part #0000- 07-5901 (discontinued DG Motorsports). If a hardtop is used, latches shall be replaced with positive fasteners. OBD2 requirement does not apply. Ballast box may be removed. ND2s with sequential gearbox allowed +100 lbs.
STU Turbo Inlet Restrictor Table
#38961 from John Weisberg · Rule change · TB 25-12 (2025-12 Fastrack)
slowerSTU 36mm restrictor allows 2830 lbs (up 10 lbs from 2820); 37mm allows 2980 lbs (down 5 lbs from 2985).
In GCR, Section 9.1.4.H.3, change chart as follows:
A specification table follows in the original; it is not shown here.
STU 275 Tire Rule
#38983 from Peter Federlin · Rule change · TB 25-12 (2025-12 Fastrack)
slowerSTU cars over 3150 lbs lose 275-tire option with 2% weight adder.
In GCR, Section 9.1.4.G.1., change as follows: "A maximum section width of 245 is permitted. Cars over 3150 lbs. may run a 275 tire with a 2% weight adder."
unclearT3 Ford Mustang EcoBoost loses optional 2-piece 355mm Brembo rotor brake kit option with 50 lb penalty.
In T3 Spec Lines, Ford Mustang EcoBoost (2015-), change Notes as follows: ", or optional 2-piece rotor 355mm max Brembo brake kit #M-2300-S allowed with +50lb penalty."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
STU STU Honda Engine weight penalty
#39375 from Super Touring Committee · Rule change · TB 25-12 (2025-12 Fastrack)
In STU Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Minimum Weight as follows: Honda K20: "Chart + 2%" Honda K24: "Chart + 2%"
GT2 Additional Body Options to Replace Older Stock Car Bodies
#39086 from Samuel Daniels · Rule change · TB 26-01 (2026-01 Fastrack)
neutralGT2 adds Cadillac CTS, Chevrolet Impala/Malibu/Monte Carlo/SS, Dodge Intrepid, Ford Fusion/Taurus, Lincoln MKS, Pontiac G8/GTO/Grand Prix, Toyota Camry, and Gen late Model Stock Car bodies.
In GCR, Section 4.8.4.2.1., add the following: "Cars in the class must use 1997, through current year, commercially available stock car bodywork. The following make/model bodies are allowed: 1. Cadillac CTS 2. Chevrolet Impala 3. Chevrolet Malibu 4. Chevrolet Monte Carlo 5. Chevrolet SS
Show 12 more lines
6. Dodge Intrepid 7. Ford Fusion 8. Ford Taurus 9. Lincoln MKS 10. Pontiac G8 11. Pontiac GTO 12. Pontiac Grand Prix 13. Toyota Camry Gen late Model Stock Car Bodies are allows: 1. Chevrolet Camaro 2. Ford Mustang 3. Toyota Camry"
T3 Request to Allow Spec Mustang to Touring 3 in Appendix M Trim
#39196 from Roger Eagleton · Rule change · TB 26-01 (2026-01 Fastrack)
fasterT3 Ford Spec Mustang restrictor opens to 45mm, weight drops to 3400 lbs.
In T3 Spec Lines, Ford Spec Mustang, change as follows: Restrictor: "Two 44mm 45mm holes" Weight: "3450 3400"
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 Tire Help for Spec E9X in T3
#39222 from Benjamin Phillips · Rule change · TB 26-01 (2026-01 Fastrack)
fasterT3 BMW Spec E9X tire width increases to 255 from 225; spec E9X tire or any DOT permitted.
In T3 Spec lines, BMW Spec 9X, change as follows: Car: "BMW Spec 9X BMW Spec E9X" Notes: "Must conform to all SpecE9X rules Version 2.10. Spec E9X spec tire permitted or any DOT permitted up to 225 255 permitted. No other touring allowances permitted. Engines may not be modified unless specified in the Spec E46 rules and must conform to touring tech procedures. Driver must possess a current copy of the rules. Dyno results do not ensure engine compliance. THIS SPEC LINE DOES NOT QUALIFY FOR SCCA RUNOFFS COMPETITION UNTIL IT HAS BEEN REPRESENTED IN 3 SCCA SUPER TOUR EVENTS."
T3 SpecE46 Tire Sizing
#39292 from Rob Piekarczyk · Rule change · TB 26-01 (2026-01 Fastrack)
fasterT3 SpecE46 permitted tire width increases from 225 to 245.
In T3 Spec Lines, BMW SpecE46, change Notes as follows: "Must conform to all SpecE46 rules Version 3.0. SpecE46 spec tire permitted or any DOT permitted up to 225 245 permitted. No other touring allowances permitted. Engines may not be modified unless specified in the Spec E46 rules and must conform to touring tech procedures. Driver must possess a current copy of the rules. Dyno results do not ensure engine compliance. SE46 HP limit does not apply."
GT2 GT3 Turbo to GT2?
#39365 from Chris Edens · Rule change · TB 26-01 (2026-01 Fastrack)
neutralGT2 Mazda BP engine 1839cc classified with 46mm turbo inlet restrictor, 2250 lbs minimum weight.
In GT2 Spec Lines, Engines - MAZDA, classify Engine Family BP as follows: GT2 Engines - MAZDA Engine Family Engine Type Bore x Stroke (mm) Disp. (CC)
Show 1 more lines
Head Type Valves /
A specification table follows in the original; it is not shown here.
T3 Alternate Placement of Fuse Panel and Electronics Request
neutralT2, T3, T4 cars may relocate under-dash electronics and fuse boxes for access after roll cage installation.
In GCR, Section 9.1.9.2.D.9.d, add the following: "8. Under-dash electronics including computers, modules and fuse boxes may be relocated so they can be easily accessed after roll cage installation."
T3 Clarify T4 Brake Rotor Allowance
#39503 from David Mead · Rule change · TB 26-01 (2026-01 Fastrack)
neutralT4 Performance now permits 1-piece alternative rotors matching spec line sizes; alternate brake kits allowed same.
In GCR, Section 9.1.9.2.D.6.a.6., change as follows: "In T2-Performance alternative rotors, including 2 piece rotors are permitted. Rotors must be within 5% of OE diameter or a maximum diameter of 360mm. In T3- Performance alternative rotors, including 2 piece rotors are permitted with a maximum diameter of 360mm. T4- Performance alternative 1-piece rotors are permitted but rotors must meet the sizes listed in the spec line. Spec lines showing alternate brake kits are also permitted to use 1-piece performance alternative rotors of the same size."
STU Request for Permission on Aftermarket Turbo Kit and Intake
#39529 from John Grim · Rule change · TB 26-01 (2026-01 Fastrack)
fasterSTU Mazda MZR (LF, L3, L5) Turbo classified; Jack Spania Racing 70 mm intake manifold and Fab9 Tuning bottom-mount turbo kit approved.
In STU Spec Lines, Table A: Alternate Vehicle and Engine Allowances, Mazda MZR (LF, L3, L5), change Notes as follows: "Short blocks, heads, and intakes may be freely swapped within these engine designations. May use Goodwin Part # 61- 2510 or, Gato Performance Part #31972 or Jack Spania Racing 70 mm sheet-metal aluminum Intake manifold. Must use stock throttle body or Acura part number 16400-PND-A17." In STU Spec Lines, Table A: Alternate Vehicle and Engine Allowances, classify Mazda MZR (LF, L3, L5) Turbo as follows: STU Maximum Displacement (cc's) Minimum Weight Notes Mazda MZR (LF, L3, L5) Turbo
Show 7 more lines
Varies Chart Short blocks, heads, and intakes may be freely swapped within these engine designations. May use Jack Spania Racing 70 mm sheet-metal aluminum Intake manifold. Must use stock throttle body or Acura part number 16400-PND- A17. Fab9 Tuning bottom-mount turbo kit approved with one of the STU approved Turbos.
GT2 Tech Bulletins for GT2 and GT2-ST
#39537 from Grand Touring Committee · Rule change · TB 26-01 (2026-01 Fastrack)
slower991.2 GT3 Cup throttle body restrictor increases from 65mm to 70mm; 997.2 loses 100 lbs to 2800; Corvette LS engines get larger restrictors across multiple displacements and model years; LS3 and LT1 weight reduced 100 lbs each to 3150.
In GT2 Spec Lines, GT2 Cars – Porsche, classify 992.1 GT3 Cup as follows: GT2 Cars – Porsche Model Year Body Style Driveline Wheel Base Notes 992.1 GT3 Cup (22-25) 2 Dr RWD 4.0L flat six. 3250lbs. w/60mm Throttle Body Restrictor (TBR). Cars must be prepared in accordance with the appropriate
Show 49 more lines
model/year Porsche factory 911 GT3 Cup parts catalog/service manual. Cars may not be altered in any way except as authorized below. Drivers must have the correct year manuals as they apply to their specific car in their possession. Safety, drivers comfort, driver control and instrumentation items may be modified per the GCR. Original factory installed Matter/ IMV roll cages are allowed. The stock unmodified fuel tank is allowed. Windshield clips must be installed per GCR 9.3 Windshield Clips/Rear Window Straps. All other SCCA safety standards apply. Tires per GCR 9.3 Tires. Lubricants, consumable fluids (brake fluid, coolant etc.) and oil filters are open free. Factory (OEM manufacturer) Lexan front windows allowed as delivered. ABS is allowed. In GT2 Spec Lines, GT2 Cars – Porsche, change Notes as follows: 991.1 GT3 Cup: "3.8L flat six. 3000lbs. w/72mm Throttle Body Restrictor (TBR). Aftermarket header allowed." 991.2 GT3 Cup: "4.0L flat six. 3000lbs. w/65mm 70mm Throttle Body Restrictor (TBR)." 997.2 GT3 Cup: "3.8L flat six. 2900 2800 lbs. Aftermarket header allowed." In GT2 Spec Lines, GT2 – ST, Chevy Corvette (-2013), change as follows: 5665: Restrictor: "81 85mm flat plate" Notes: "GM LS1, LS6. LS1/LS6 C6 Corvettes using the OEM C6 intake manifold and 90 mm throttle body must use a 78mm flat plate restrictor. OEM 75mm throttle body and manifold do not require a restrictor. LS6 may reduce weight by 50 lbs. L S1/LS6 alternate intake manifold, DORMAN part # 615-900." LS2 5967 Restrictor: "83 85mm " L76 5967 Restrictor: "80 83mm flat plate" LS3 6162 Restrictor: "80 83mm flat plate" 6162 GM LS3: Weight: "3250 3150" Restrictor: "74 80mm flat plate" 6162 GM LT1: Weight: "3250 3150" Restrictor: "74 77mm flat plate" In GT2 Spec Lines, GT2 – ST, Chevy Corvette (14-19), change as follows: 5665: Restrictor: "83 85mm flat plate" Notes: "GM LS1, LS6. LS1/LS6 C6 Corvettes using the OEM C6 intake manifold and 90 mm throttle body must use a 78mm flat plate restrictor. OEM 75mm throttle body and manifold do not require a restrictor. LS6 may reduce weight by 50 lbs. L S1/LS6 alternate intake manifold, DORMAN part # 615-900." LS2 5967: Weight: "3100 3000" Restrictor: "83 85mm flat plate" L76 5967 Restrictor: "80 83mm flat plate" 6162 Restrictor: "80 83mm flat plate" 6162 LS3: Weight: "3200 3100" Restrictor: "77 80mm flat plate" 6162 LT1: Weight: "3200 3100" Restrictor: "74 80mm flat plate"
GT2 Allow Larger Air Cooled Engines in Porsche 911 GT2
fasterGT2 Porsche 911 SC gains option of 4.0L 4V engine at 2350 lbs or 4.0L 2V at 2275 lbs.
In GT Spec Lines, create GT Cars - PORSCHE and classify SC as follows: GT Cars - PORSCHE Model Years Body Style Drive- line Wheel- base (in) Notes SC 1978 2 Dr. Rear engine/RWD 89.45 May use alternate engine bore. 4.0L 2V @2275 lbs. 4.0L 4V @ 2350 lbs.
GT2 Classify T1 BMW in GT2
#39408 from Jared Lendrum · Rule change · TB 26-02 (2026-02 Fastrack)
neutralM3 E92 classified in GT2 with 3999cc V8, 35mm restrictor, 3300 lbs minimum weight.
In GT Spec Lines, classify M3 E92 in GT Cars - BMW as follows: GT Cars - BMW Model Years Body Style Drive- line Wheel- base (in) Notes M3 E92 (08-13) 2 Dr. RWD 108.7 Cannot be built to any other rule set.
Show 5 more lines
In GT Spec Lines, classify M3 E92 in GT Engines - BMW - BMW as follows: GT Engines - BMW Engine Family Engine Type Bore x Stroke
A specification table follows in the original; it is not shown here.
T3 Please change 2011-2014 Mustang V6 Spec Line to 2005-2014
#39558 from Matthew Miller · Rule change · TB 26-02 (2026-02 Fastrack)
neutralT3 Ford Mustang V6 Spec Line expands to include 2005-2010 chassis and body with 2011-2014 engine.
In T3 Spec Lines, Ford Mustang V6 (11-14) , add to Notes the following: "2005-2010 chassis/body permitted."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 Nissan 350Z Weight Request
#39598 from David Muramoto · Rule change · TB 26-02 (2026-02 Fastrack)
fasterT3 Nissan 350Z DE Motor loses 25 lbs to 3100, HR Motor loses 25 lbs to 3250.
In T3 Spec Lines, Nissan 350Z Track/ Touring/Standard/ Nismo (03-08), change Weight as follows: DE Motor: "3125 3100" HR Motor: "3275 3250"
T3 Allow Alt Bushing Material in Toe Links
#39607 from David Mead · Rule change · TB 26-02 (2026-02 Fastrack)
fasterT2-T4 adjustable toe links now allow performance alternative bushings and spherical bearings, previously prohibited except in specified examples.
In GCR, Section 9.1.9.D.5.a.1., change as follows: "T2-T4: A maximum of 3.5 degrees of negative camber is allowed on front and rear suspensions. Spec line part(s) may not be modified to increase caster and camber. Strut suspensions may adjust camber and caster by the use of eccentric bushings, eccentric bolts (crash bolts) at the strut-to-spindle, and/or by use of slotted adjustment plates at the top of the strut mounting plate. If upper strut slotted adjustment plates are used, they shall be located on existing chassis structure, utilizing the unmodified manufacturer’s original bolt holes and may not serve as reinforcement for that structure. Slotted adjustment plates (strut camber plates) may incorporate a single spherical bearing (spherical bushing) and a ball thrust bearing per strut tower. On other forms of suspension, camber and caster adjustment may be achieved by the use of shims and/or eccentric
Show 4 more lines
bushings. Adjustable toe links with spherical bearings are permitted and may serve no purpose other than adjusting toe angle. Adjustable toe links are permitted. They are allowed to have performance alternative bushings and spherical bearings. They may serve no purpose other than adjusting toe angle. Spherical bearings/bushings are not permitted in T2-T4 except for the specific examples listed in the class rules or vehicle spec line."
What the rules allowed changed as listed; this does not say what any particular car ran.