Quickest here:P2 1:09.928 Tim Day Jr, Cal Club 2023 qualifying · T1 1:46.465 Ian Barberi, Cal Club 2025 qualifying · FF 1:51.118 Eric Poulsen, Cal Club 2025 race
P2T1FFsolid race · dashed qualifying · slower is lower
P2T1FFsolid race · dashed qualifying · each class's best lap as a share of P2's at the same event (the reference class, changeable above); 100% is level, higher is quicker
Event
P2
T1
FF
Qual best
Race best
Trap
Qual best
Race best
Trap
vs P2
% of P2
Qual best
Race best
Trap
vs P2
% of P2
Cal Club 2026 CALCL262026-02-21
1:37.278Tim Day Jr · only car+27.350s (+39.11%)
1:39.758Tim Day Jr · only car
155.4Tim Day Jr
1:59.760Ed Gless · only car+13.295s (+12.49%)
1:59.123Ed Gless · only car+11.689s (+10.88%)
120.7Ed Gless-18.6 mph (-13.3%)
+19.365squal +22.482s
119.4%qual 123.1%
1:53.098Edward Erlandson · fastest of 2+1.054s (+0.94%)
1:54.741Edward Erlandson · fastest of 2+3.623s (+3.26%)
133.7Edward Erlandson+19.0 mph (+16.5%)
+14.983squal +15.820s
115.0%qual 116.3%
16 rule changes (T1: 13, FF: 3)4 weight · 3 cars added · 3 tyres & wheels · 2 induction · 1 removed · 3 wording · T1 Corvette C6 LS1/LS6 Spec Line reinstated: 3200 lbs minimum weight, 70mm restrictor required. · FF clarifies alternative tire eligibility for cars homologated 1989 or earlier with rocker arm or outboard suspension on all four corners. · T1 Spec Line restrictor changes from 70mm flat plate to unspecified new specification. · Unable to summarize: letter states intent but provides no actual rule changes to S2000 specification. · T1 non-GT4 cars: multiple restrictors enlarged (70mm to 73mm, 75mm to 78mm, 55mm to 60mm, 61mm to 70mm); one weight increased to 3600. · T1 BMW M3 E92 (08-13) Spec Line 1090 removed entirely. · FF adds rocker arm and outboard suspension cars optional bias ply and VFF tires; removes front-as-rear rule, adds mixing restrictions. · Porsche 981 GT4 Clubsport added to T1 as spec line 4085, minimum weight 3100 lbs with driver. · T1 Honda S2000 minimum weight reduced from 2950 lbs to 2900 lbs. · T1 BMW E46 M3 permits BMW #GS7D36SG aftermarket sequential transmission in SL# 1060 and 1070. · T1 BMW M3 E92 minimum weight reduced to 3300 lbs. · T1 Mustang Darkhorse R gets 315 front and rear tyres, loses 500 lbs minimum weight to 3600. · Cadillac CT4-V Blackwing added to T1 Spec Line 1115, 3564cc, 3750 lbs minimum weight. · FF allows older cars with rocker arm or outboard suspension to use bias ply slicks or VFF tires instead of radials. · T1 Mustang Spec 1430 restrictor opens 60mm to 65mm; Spec 1460 weight rises to 3500 lbs, restrictor 70mm; Corvette 1190 restrictor opens 67mm to 70mm; BMW 1090 restrictor narrows 40mm to 35mm; BMW 1100 weight rises to 3350 lbs.showhide
T1 LS1 into Corvette C6 Spec Line Request #39716cars addedneutralT1 Corvette C6 LS1/LS6 Spec Line reinstated: 3200 lbs minimum weight, 70mm restrictor required.
FF Formula F Alternative Tire Rule Proposed Clarifications #39281wordingneutralFF clarifies alternative tire eligibility for cars homologated 1989 or earlier with rocker arm or outboard suspension on all four corners.
T1 additional T1 adjustment #39520inductionunclearT1 Spec Line restrictor changes from 70mm flat plate to unspecified new specification.
T1 Keep S2000 Classification #39344wordingunclearUnable to summarize: letter states intent but provides no actual rule changes to S2000 specification.
T1 Correcting and updating T1 GT4 spec lines #39394weight
T1 BOP adjustments to non GT4 T1 cars #39406induction +100 lbsfasterT1 non-GT4 cars: multiple restrictors enlarged (70mm to 73mm, 75mm to 78mm, 55mm to 60mm, 61mm to 70mm); one weight increased to 3600.
T1 Remove T1 Spec Line #39407removedneutralT1 BMW M3 E92 (08-13) Spec Line 1090 removed entirely.
FF Page 228, FF tire rule 9.1.1.10.e #38251tyres & wheelsneutralFF adds rocker arm and outboard suspension cars optional bias ply and VFF tires; removes front-as-rear rule, adds mixing restrictions.
T1 Acceptance of Porsche 981 GT4 Clubsport into T1 #36664cars addedneutralPorsche 981 GT4 Clubsport added to T1 as spec line 4085, minimum weight 3100 lbs with driver.
T1 Request to Restore T1 Honda S2000 to Proper Weights #37644weight -50 lbsfasterT1 Honda S2000 minimum weight reduced from 2950 lbs to 2900 lbs.
T1 DCT Transmission in E46 #37964wordingneutralT1 BMW E46 M3 permits BMW #GS7D36SG aftermarket sequential transmission in SL# 1060 and 1070.
T1 Reduce E92 M3 Minimum Weight to 3050 #38092weightfasterT1 BMW M3 E92 minimum weight reduced to 3300 lbs.
T1 Finalize Spec Line for T1 Darkhorse #38106tyres & wheelsfasterT1 Mustang Darkhorse R gets 315 front and rear tyres, loses 500 lbs minimum weight to 3600.
T1 Cadillac CT4-V Blackwing #38003cars addedneutralCadillac CT4-V Blackwing added to T1 Spec Line 1115, 3564cc, 3750 lbs minimum weight.
FF Formula F Proposal to Invite Older Cars Via a Tire Rule Change #37802tyres & wheelsfasterFF allows older cars with rocker arm or outboard suspension to use bias ply slicks or VFF tires instead of radials.
T1 Correct and make new T1 BOP adjustments. #37737weight +75 lbsunclearT1 Mustang Spec 1430 restrictor opens 60mm to 65mm; Spec 1460 weight rises to 3500 lbs, restrictor 70mm; Corvette 1190 restrictor opens 67mm to 70mm; BMW 1090 restrictor narrows 40mm to 35mm; BMW 1100 weight rises to 3350 lbs.
Cal Club 2025 CALCL252025-02-22
1:46.465Ian Barberi · fastest of 2
1:47.434Ian Barberi · fastest of 3 · top 3 within 11.8s
139.3Drew Delmonico
1:52.044Eric Poulsen · only car
1:51.118Eric Poulsen · only car
114.7Eric Poulsen
57 rule changes (P2: 10, T1: 42, FF: 5)12 cars added · 7 weight · 5 engine · 5 induction · 3 tyres & wheels · 1 aero · 1 removed · 22 wording · 1 other · T1 Mustang gains 125 lbs to 3600, restrictor shrinks 65mm to 60mm. Corvette gains 50 lbs to 3500, restrictor shrinks 70mm to 67mm. BMW deleted. · T1 E46 M3 Spec Line 1050 allows VAC Motorsports throttle body VAC-TB-S54 on 3.250L engine instead of Dinan. · T1 Chevrolet Corvette C8 (2023-23) minimum weight reduced from 3600 lbs to 3500 lbs. · T1 Chevrolet Camaro Gen 5 restrictor increases from 75mm to 80mm flat plate. · T1 Audi R8 GT4 Spec Line #4020 maximum tyre size changes to 315 DOT, 305/645, or 30/65-18 (f), 33/68-18 (r) Non-DOT. · P2 2000cc Pinto engine car minimum weight set to 1335 lbs. · T1 GT4 tire sizes adjusted across ten cars: most non-DOT rear to 305/660, Audi and McLaren 305/645, Camaro and Mustang 305/680. · BMW M4 GT4 (G82) added to T1 GT4 at 3525 lbs minimum weight with Red power stick control. · T1 Spec Lines now permits 5.5 inch clutch in Engine Notes. · T1 GT4 Spec Line 4020 restrictor opens from 44mm to 45mm, minimum weight drops to 3400 lbs. · Mustang Darkhorse R added to T1 homologated cars at 3,250 lbs minimum with 305/315 tires, ineligible for Runoffs until 3 Super Tour events. · T1 Corvette may roll or flatten wheel opening lips for tire clearance; plastic fenders may remove lips if edge thickness matches basic material. · T1 E46 M3 S54 can now use Dinan Throttle Body #D760-3400 on 3.250L engine. · FF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs. · FF Honda Fit allows Fast Forward 0.25mm oversize pistons PN FF800-110 as alternative; piston diameter spec clarified to 2.8835 inches. · FF VTEC activation valve must function; EGR blanking plate rule clarified with Fast Forward part numbers. · P2 Spec ECU engine modifications clarified: oil system, ECU, and exhaust unrestricted only. · P2 FIA Group CN spec notes clarified: Series changed to Challenge, documentation requirement moved to online link. · Mercedes AMG-C63 S (2023) classified in T1 with 4000 lbs minimum weight and 3700 restrictor. · T1 Honda S2000 classified with 2400 lb minimum weight, 2950 cc displacement, 4.75" supercharger pulley. · Pontiac GTO 2006-2009 LS1 added to T1 as Spec Line 1590, 5700 cc, 3400 lbs minimum. · C8 Corvette T1 restrictor plate increases from 70mm to 72mm flat plate. · T1 NEW class removes 23 spec lines including Acura NSX, Ferrari, Porsche 996, Nissan Z cars, and others; Porsche 997 spec line 1680 expiration removed. · FF Honda Fit gains Fast Forward FF800-100 oversize piston ring pack option. · P2 AMAC modified engine range clarified to 2008 and older stock engines only, restrictor 38mm, weight 1025 lbs. · P2 Suzuki GSX-R1000 07/08 engine crankcase may swap to GSX-S1000 16/19 part #11301-04840. · T1-GT4 batch adjustments: five cars lighter, two heavier, restrictors and ECU maps changed, five models now eligible for Runoffs. · T1 spec lines 1000, 1010, 1020, 1040, 1360, 1400–1410, 1520–1680, 1700–1720 deleted entirely. · P2 Table 1 corrects engine date ranges and brand specifications for Stock and Modified engines across multiple car models. · T1 Chevrolet Corvette C5 LS2 added with 6000cc displacement, 3300 lbs minimum weight, 72mm flat plate restrictor. · T1 Chevrolet Corvette C7 (14-19) including Z51, Grandsport newly classified as homologated car. · T1 Gen 5 Camaro minimum weight drops 75 lbs to 3475; restrictor increases 70mm to 75mm. · T1 Aston Martin Vantage permitted to use OEM Sportshift II transmission. · Pontiac GTO 2006-2009 re-integrated into T1 with LS2 at 3400 lbs, 72mm restrictor, and LS3 at 3500 lbs, 61mm restrictor. · T1 Porsche 997-1 GT3 Cup added at spec line 4210, minimum weight 3050 lbs. · Chevrolet Camaro GT4-R classified in T1 GT4 Spec Line 4035, minimum weight 3375 lbs, 315 max tire, 63mm restrictor, ineligible for Runoffs. · T1 Dodge Viper ACR / SRT RT-10 and ACR/ACR-X spec lines 1350 and 1370 remove 12/23 expiration. · T1 GT4 McLaren 570S, Mercedes AMG GT4, and Porsche 718 Cayman GT4 CS MR now eligible for Runoffs competition. · T1 GT4 BMW M4 Spec Line Number changed from 4050 to 4030. · T1 Corvette C5 gains approved aero parts: carbon rear spoiler, vented front splitter, side skirts, with 50 lb weight reduction allowed. · T1 Dodge Viper ACR/ACR-X restrictor increases from 50mm to 60mm flat plate. · T1 Dodge Viper ACR/ACR-X: Spec Line 1370 restrictor increases to 55mm, Line 1390 decreases to 55mm. · T1 Ford Mustang S197 05-14 now requires OEM 8.8 differential housing. · T1 Chevrolet Camaro Gen 5 LS7 gets two spec lines: 1131 with 70mm restrictor, 1136 with 53mm restrictor, both 3450 lbs minimum. · T1 Chevrolet Camaro Gen 5, Corvette C5 and C6: engine resleeve restricted to stock parameters only, no longer LS3 bore/stroke. · T1 Ford Mustang S197 (05-14) reinstated with 3550 lbs minimum weight, 75mm restrictor, Voodoo engine permitted. · P2 side body height requirement clarified: outermost surface between wheel openings must equal front axle centerline height. · P2 closed cockpit single seat cars now prohibited unless specifically allowed in Table 1. · T1 GT4 weights clarified for nine cars, ranging from 3200 lbs Porsche 718 Cayman to 3575 lbs Aston Martin. · T1-GT4 McLaren 570S and Mercedes AMG GT4 front tires widen to 315 mm. · P2 engine table wording updated; redundant effective date language removed. · P2 motorcycle engines: 2011+ Kawasaki restrictor reduced to 34mm, minimum weight raised to 1100 lbs; 2009+ other brands weight raised to 1100 lbs. · T1 Chevrolet Camaro Gen5 LS3-6160 adds 70mm flat plate restrictor, weight 3550 lbs. · FF Honda Fit engine adds Fast Forward part number alternatives for intake, exhaust, oil system, and scavenge pump components. · T1 cars with aftermarket sequential transmissions get 10-inch max bellhousing; non-sequential cars gain 100 lbs weight break. · T1 GT4 all nine cars lose 125 lbs minimum weight with driver, from 3200–3575 to 3075–3450. · T1 removes GCR Section 9.1.9.1.A. and T1 Spec Lines entirely, sunsetting pre-2023 Touring 1 rules.showhide
T1 T1 Parity Compared to GT4 #37170weight +125 lbsslowerT1 Mustang gains 125 lbs to 3600, restrictor shrinks 65mm to 60mm. Corvette gains 50 lbs to 3500, restrictor shrinks 70mm to 67mm. BMW deleted.
T1 Clarification of Request Approval #37273 #37399engineunclearT1 E46 M3 Spec Line 1050 allows VAC Motorsports throttle body VAC-TB-S54 on 3.250L engine instead of Dinan.
T1 C8 Corvette Facts #37400weight -100 lbsfasterT1 Chevrolet Corvette C8 (2023-23) minimum weight reduced from 3600 lbs to 3500 lbs.
T1 Camaro Gen 5 Competitive Disadvantage #37440inductionfasterT1 Chevrolet Camaro Gen 5 restrictor increases from 75mm to 80mm flat plate.
T1 Tire Changes in the Rules for GT4 #37497tyres & wheelsunclearT1 Audi R8 GT4 Spec Line #4020 maximum tyre size changes to 315 DOT, 305/645, or 30/65-18 (f), 33/68-18 (r) Non-DOT.
P2 2000 cc Pinto Engine Car Weight #37187weightslowerP2 2000cc Pinto engine car minimum weight set to 1335 lbs.
T1 Changes to T1 Tires for GT4 and Other Cars #35383tyres & wheelsunclearT1 GT4 tire sizes adjusted across ten cars: most non-DOT rear to 305/660, Audi and McLaren 305/645, Camaro and Mustang 305/680.
T1 G82 M4 GT4 inclusion in T1 #35864cars addedneutralBMW M4 GT4 (G82) added to T1 GT4 at 3525 lbs minimum weight with Red power stick control.
T1 Alt. Clutch Allowance #36606wordingneutralT1 Spec Lines now permits 5.5 inch clutch in Engine Notes.
T1 BOP Changes Need Updates #36667weight -150 lbsfasterT1 GT4 Spec Line 4020 restrictor opens from 44mm to 45mm, minimum weight drops to 3400 lbs.
T1 Request Ford Performance Darkhorse R in T1 #37136cars addedneutralMustang Darkhorse R added to T1 homologated cars at 3,250 lbs minimum with 305/315 tires, ineligible for Runoffs until 3 Super Tour events.
T1 Car Mods for T1 Corvette under line item 1150 #37173wordingneutralT1 Corvette may roll or flatten wheel opening lips for tire clearance; plastic fenders may remove lips if edge thickness matches basic material.
T1 Increased Bore Throttle Bodies for E46 M3 S54 Engine #37273enginefasterT1 E46 M3 S54 can now use Dinan Throttle Body #D760-3400 on 3.250L engine.
FF Change FF/FC Weight with Sequential Gearbox #36651weightfasterFF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs.
FF Alternative Oversize Honda Fit Pistons #37064wordingneutralFF Honda Fit allows Fast Forward 0.25mm oversize pistons PN FF800-110 as alternative; piston diameter spec clarified to 2.8835 inches.
FF Update to FF EGR Blanking Plate Rule #36633wordingneutralFF VTEC activation valve must function; EGR blanking plate rule clarified with Fast Forward part numbers.
P2 E&O - Correct FIA Group CN spec line notes #35900wordingneutralP2 FIA Group CN spec notes clarified: Series changed to Challenge, documentation requirement moved to online link.
T1 Please Expedite classing the C63 Mercedes #35987cars addedneutralMercedes AMG-C63 S (2023) classified in T1 with 4000 lbs minimum weight and 3700 restrictor.
T1 Honda S2000 #35582cars addedneutralT1 Honda S2000 classified with 2400 lb minimum weight, 2950 cc displacement, 4.75" supercharger pulley.
T1 9.1.9.1 T1 new category item/ line 26 rule to expire Jan 1 2023 #35411cars addedneutralPontiac GTO 2006-2009 LS1 added to T1 as Spec Line 1590, 5700 cc, 3400 lbs minimum.
T1 C8 Corvette T1 Restrictor Plate Request #35213inductionfasterC8 Corvette T1 restrictor plate increases from 70mm to 72mm flat plate.
T1 The Cars Have Expired #35379removedneutralT1 NEW class removes 23 spec lines including Acura NSX, Ferrari, Porsche 996, Nissan Z cars, and others; Porsche 997 spec line 1680 expiration removed.
FF Honda Fit Oversize Piston Rings #35305wordingneutralFF Honda Fit gains Fast Forward FF800-100 oversize piston ring pack option.
P2 E&O - Clarify B.1 modified engine range in AMAC spec lines #35225wordingneutralP2 AMAC modified engine range clarified to 2008 and older stock engines only, restrictor 38mm, weight 1025 lbs.
P2 Replacement Engine Crankcase for 07/08 Suzuki GSX-R1000 Engines #35340engineunclearP2 Suzuki GSX-R1000 07/08 engine crankcase may swap to GSX-S1000 16/19 part #11301-04840.
T1 GT4 batch adjustment in T1 #35162other -85 lbsunclearT1-GT4 batch adjustments: five cars lighter, two heavier, restrictors and ECU maps changed, five models now eligible for Runoffs.
P2 Correct Table 1 for Engine Date Range Specifications #35182wordingneutralP2 Table 1 corrects engine date ranges and brand specifications for Stock and Modified engines across multiple car models.
T1 New T1 add spec line for C5 corvette LS2 engines (Copy from C6) #33764cars addedneutralT1 Chevrolet Corvette C5 LS2 added with 6000cc displacement, 3300 lbs minimum weight, 72mm flat plate restrictor.
T1 C7 Corvette Rule Change Request #34897cars addedneutralT1 Chevrolet Corvette C7 (14-19) including Z51, Grandsport newly classified as homologated car.
T1 Camaro Gen 5 Weight Reduction Due to Competitive Disadvantage #35092weight -75 lbsfasterT1 Gen 5 Camaro minimum weight drops 75 lbs to 3475; restrictor increases 70mm to 75mm.
T1 Addendum to Letter #35022: Drivetrain Rule #35105wordingneutralT1 Aston Martin Vantage permitted to use OEM Sportshift II transmission.
T1 2004 - 2006 Pontiac GTO Re-Integration Back Into T1 #34403cars addedneutralPontiac GTO 2006-2009 re-integrated into T1 with LS2 at 3400 lbs, 72mm restrictor, and LS3 at 3500 lbs, 61mm restrictor.
T1 Request to Classify Porsche 997-1 GT3 Cup #34561cars addedneutralT1 Porsche 997-1 GT3 Cup added at spec line 4210, minimum weight 3050 lbs.
T1 Why no Camaro? #34421cars addedneutralChevrolet Camaro GT4-R classified in T1 GT4 Spec Line 4035, minimum weight 3375 lbs, 315 max tire, 63mm restrictor, ineligible for Runoffs.
T1 Request to Remove Expiration from T1 spec lines #1350 & #1370 #34470wordingneutralT1 Dodge Viper ACR / SRT RT-10 and ACR/ACR-X spec lines 1350 and 1370 remove 12/23 expiration.
T1 Remove #34475wordingneutralT1 GT4 McLaren 570S, Mercedes AMG GT4, and Porsche 718 Cayman GT4 CS MR now eligible for Runoffs competition.
T1 Error in T1 GT4 numbering scheme- #34578wordingneutralT1 GT4 BMW M4 Spec Line Number changed from 4050 to 4030.
T1 C5 Approved Aero That Was Mistakenly Deleted #34374aerofasterT1 Corvette C5 gains approved aero parts: carbon rear spoiler, vented front splitter, side skirts, with 50 lb weight reduction allowed.
T1 Viper Cleanup #34107inductionfasterT1 Dodge Viper ACR/ACR-X restrictor increases from 50mm to 60mm flat plate.
T1 Viper 8300 OEM FPR Size #34268inductionunclearT1 Dodge Viper ACR/ACR-X: Spec Line 1370 restrictor increases to 55mm, Line 1390 decreases to 55mm.
T1 Ford Mustang S197 (05-14) Clarification #34450wordingneutralT1 Ford Mustang S197 05-14 now requires OEM 8.8 differential housing.
T1 Gen 5 Camaro Engine #33875cars addedneutralT1 Chevrolet Camaro Gen 5 LS7 gets two spec lines: 1131 with 70mm restrictor, 1136 with 53mm restrictor, both 3450 lbs minimum.
T1 Inquiry to letter #33682 #34071engineslowerT1 Chevrolet Camaro Gen 5, Corvette C5 and C6: engine resleeve restricted to stock parameters only, no longer LS3 bore/stroke.
T1 Request to reinstate T1 S197 Mustang #34048cars addedneutralT1 Ford Mustang S197 (05-14) reinstated with 3550 lbs minimum weight, 75mm restrictor, Voodoo engine permitted.
P2 Clarify minimum side body height requirement #34143wordingneutralP2 side body height requirement clarified: outermost surface between wheel openings must equal front axle centerline height.
P2 Clarify closed cockpit single seat car allowance #34144wordingneutralP2 closed cockpit single seat cars now prohibited unless specifically allowed in Table 1.
T1 T1 GT4 adjustments #33786wordingneutralT1 GT4 weights clarified for nine cars, ranging from 3200 lbs Porsche 718 Cayman to 3575 lbs Aston Martin.
T1 Touring 1 Tire Sizes #34191tyres & wheelsfasterT1-GT4 McLaren 570S and Mercedes AMG GT4 front tires widen to 315 mm.
P2 Remove redundant effective date language and update engine table #34012wordingneutralP2 engine table wording updated; redundant effective date language removed.
P2 E&O - Correct dimensional equivalents #34038engineslowerP2 motorcycle engines: 2011+ Kawasaki restrictor reduced to 34mm, minimum weight raised to 1100 lbs; 2009+ other brands weight raised to 1100 lbs.
T1 Clarification for Camaro Gen5 2010-2015 #33739inductionslowerT1 Chevrolet Camaro Gen5 LS3-6160 adds 70mm flat plate restrictor, weight 3550 lbs.
FF Add Fast Forward Part Numbers for Honda Fit Engine #33752wordingneutralFF Honda Fit engine adds Fast Forward part number alternatives for intake, exhaust, oil system, and scavenge pump components.
T1 Sequential Gearbox Limitations in T1 #33691wordingneutralT1 cars with aftermarket sequential transmissions get 10-inch max bellhousing; non-sequential cars gain 100 lbs weight break.
T1 T1 GT4 adjustments #33786weightfasterT1 GT4 all nine cars lose 125 lbs minimum weight with driver, from 3200–3575 to 3075–3450.
T1 Sunset of pre 2023 Touring 1 Rules. #33916wordingneutralT1 removes GCR Section 9.1.9.1.A. and T1 Spec Lines entirely, sunsetting pre-2023 Touring 1 rules.
Cal Club 2023 CALCL232023-02-24
1:09.928Tim Day Jr · fastest of 2
110 earlier rule changes on record, in force before Cal Club 2023 (from 2019)18 cars added · 15 weight · 13 induction · 8 engine · 6 aero · 4 tyres & wheels · 3 suspension & brakes · 42 wording · 1 other · GT4 McLaren 570S maximum tire size changes to 285 front, 315 rear. · Sebeco NP01-EVO and Elan NP01 Mazda 2.0L MZR added to P2, 1600 lb minimum, no restrictor required. · P2 Radical SR3/SR4/Cup/Club Sport/Pro-Sport/PR6 removes assisted shifting requirement across all spec lines. · P2 chassis rules clarified to allow composite materials in non-fully-composite construction; anti-intrusion panel attachment standardized; Stohr and converted F600 cars added with specific allowances. · Unable to summarize: the change to P2 Engine Table Spec Line B.1 is not detailed in the provided text. · Eight GT4 models added to T1 with weights from 3200 to 3575 lbs and restricted power per SRO 2022 rules. · T1 Cadillac CTS/CTS-V, Chevrolet Camaro, Pontiac Firebird, Pontiac GTO 6162 OEM minimum weight reduced to 3475 lbs. · T1-LP Ford Mustang FP350S restrictor increases from 70mm to 75mm. · Mercedes Benz AMG GT4 2017-2021 classified T1 Maximum at 3400 lbs minimum weight with HP-controlled SRO Power Level 2 engine. · P2 chassis construction rules clarified: fully composite or partially composite requiring composite for mobility allowed; partial composite must roll without composite parts. · P2 classification wording cleaned up in GCR section 9.1.8.C and Contents. · P2 Oldsmobile cam rules clarify aftermarket manufacturer requirements; wording only. · T1 Dodge Viper ACR displacement rises to 8400 OEM, minimum weight drops to 3550 lbs. · T1 Limited T1 wording changed to clarify all T1 cars permitted specifications. · T1 Mazda RX-7 classified: 2700 lbs minimum weight, 44mm restrictor, 13B Rotary with single Garrett Turbo #3076. · P2 adds Beasley B2 spec line with 1350 lbs, Mazda 12A, 40.5mm venturi, 16.5in wing. · P2 wing specs correct terminology from 'cord' to 'chord' for 16.5in single or dual element wings. · P2 Converted F5 cars reclassified as Converted F500 cars; suspension must comply with F500 requirements, minimum width 55 inches. · T1 Cadillac CTS/CTS-V, Chevrolet Camaro, Pontiac Firebird, Pontiac GTO LS3 minimum weight reduced to 3475 lbs. · T1 Camaro maximum displacement 7011 loses 50 lbs, to 3500. · T1 removes 33mm brake rotor thickness limit; rotors now unrestricted on thickness. · P2 motorcycle engines increase to 1505cc max, two-stroke to 1205cc max; automotive engines gain 50 lbs minimum weight to 1350. · P2 Control Area definition narrowed; aerodynamic attachments and vertical structures like turning vanes now prohibited. · P2 Engine Table Spec Line B.1 changed effective 1-1-22, details not provided in excerpt. · P2 Control Area definition clarified: floor extensions and aerodynamic attachments on bottom or top side now explicitly included. · T1 Mazda MX-5 Miata MazdaSpeed minimum weight rises to 2550 lbs, restrictor increases to 42mm. · T1 Chevrolet Corvette Cadillac XLR classified for model years through 2019. · P2 CN Honda K20A-FD2 engine rebuild rules clarified: machining prohibition replaced with specific restrictions on balancing, porting, polishing, valve jobs, cylinder honing. · Converted F5 cars in P2 minimum width reduced to 55 inches from F5 spec. · P2 clarifies minimum body width requirement between front and rear wheels for Ralt RT40, RT41, Swift 008, 014. · T1 BMW E46/E36/Z3 minimum weight increases to 2700 lbs, 3.4L engine car to 2750 lbs. · T1 Dodge Viper SRT-10 restrictor increases from 45mm to 57mm. · T1 Chevrolet Corvette Cadillac XLR LS6 engine now permits Casting #799 heads with no other head modifications. · T1 Ford Mustang Shelby/GT350/GT500 5.0L Coyote restrictor opens from 65mm to 70mm flat plate. · T1 Dodge Viper SRT-10 restrictor increases from 45mm to 57mm. · T1-LP Chevrolet Corvette C7 restrictor increases from 70 to 73 mm. · T1-LP Corvette Z06 06-13 now allows aluminum chassis replacement with equivalent OE steel chassis. · P2 tonneau covers now allowed to meet minimum dimensions; equipment attachment requirements clarified. · P2 multiple chassis models remove effective dates from Table 1 specifications. · P2 engines limited to 4 valves per cylinder maximum across all three spec lines. · T1 Chevrolet Camaro with 6162 displacement minimum weight reduced to 3500 lbs. · T1-LP Chevrolet Corvettes C5 Z06, C6 Grand Sport, and Z06 dry sump kit notes clarified to remove contradictions. · FF block relief permitted only as needed to fit allowed crankshaft. · P2 adds new spec line for 2-cycle 3-cylinder engine up to 820cc with 10 front and 14-15 rear wheel width. · T1 LP removes 50 lbs weight allowance for stock headers, adds aero device allowance up to 100 lbs, permits headers. · T1 Ford Mustang Challenge 3-valve maximum displacement changes to 4600/5000. · T1 BMW E46 now allows carbon or fiberglass OEM-style dashboards with 25 pound penalty. · T1 Ford Mustang/Thunderbird limited to Shelby/Shelby GT350/GT500 models through 2018. · Dodge Viper ACR classified in T1 with 8400cc displacement, 3600 lbs minimum weight, 55mm restrictor. · BMW M2CS Club Sport classified in T1-LP Spec Lines effective 2021-02-01. · Porsche 997.1 GT3 Cup (2006-2011) classified in T1 at 3600cc, 3150 lbs minimum weight. · T1 Chevrolet Corvette Z06 years extended from 06-12 to 06-13. · FF class cylinder head may now have optional coolant bleed line fitting to top of head for air release. · FF Honda LC1 ECU by HPD permitted effective 12/1/2020, must use HPD lambda sensor. · P2 Honda K20A-FD2 intake restrictor reduced from 55mm to 50mm, making cars faster. · T1 Corvette C8 Z51 gets wider wheels and tyres, weight drops 100 lbs to 3550. · P2 rear wing requirements clarified: standard wing 6×12 inches, end plates 14-inch square; alternate 110cm width wing 9×18 inches, end plates 14×18 inches. · FF Honda LC1 ECU implementation date changed from 3/1/2020 to pending availability of support materials. · T1 rear wing Gurney flap wording clarified: Gurney flap in chord length and mounting height rules. · Elan NP01 classified in P2 Table 1 as Spec Line car with 2000cc displacement and P2 Engine Table restrictor. · T1 and T2 Corvettes may convert leaf spring suspension to coilover with 800 lb max spring rate allowed. · P2 Enterprises Sports Racer adds 55mm flat plate intake restrictor Part # WM303013 as alternative to SIR. · T1 Porsche 996 GT3 Cup eligible model years changed from 2002-2005 to 1998-2004. · T1 Corvette and Cadillac XLR permitted to install SCRSPLR-001 rear spoiler with OE bodywork. · T1 Gen 5 Camaro allowed 366mm OEM rear rotor and caliper without weight penalty. · FF alternator changes from not required to optional. · P2 Enterprise Sports Racer 2.3L engine now requires SIR or Flat Plate restrictor sized in 0.5mm increments. · T1 Porsche 996 Spec Lines now allows 996 Cup Replica Rear deck lid. · T1 Acura NSX Turbo World Challenge and Audi TTRS GTS 2011 now require DOT tires per GCR section 9.3. · FF allows Honda HPD LC1 low-cost ECU with lambda sensor; E1 ECU no longer supported but existing units permitted if sealed. · FF rain tyres now allow Hoosier W3 Radial in addition to existing Hoosier Wet option. · P2 fly-by-wire throttle control wording clarified: stock ECUs with drive-by-wire must activate original throttle shaft mechanism. · T1 BMW E46 wagon with S54 engine allowed; displacement corrected from 3200 to 3250cc. · T1 adds Subaru WRX/WRX STI 2005-2020 at 3000 lbs minimum weight with 46 mm restrictor. · T1 Ford Mustang GT (15-17) and GT5.0L (2018-) weight raised to 3500 lbs; Brembo BBK 380mm now at no penalty; restrictors removed from notes. · T1 Ford Mustang/Thunderbird 5000 Coyote OEM reclassified to include 2015–2017 and 2018+ model years with 65mm restrictor for 18+. · T1 BMW M3 E92 carbon dash allowed with 25 lb penalty. · T1 Corvette C5 Z06, C6 coupe, C6 Grand Sport, and Z06 may convert leaf springs to conventional coilover suspension. · P2 adds BMW to motorcycle-based engine options in 4-cycle line alongside Kawasaki, Suzuki, Yamaha, Honda. · P2 Honda K20A-FD2 non-composite chassis must use 55mm flat plate intake restrictor at 1500 lbs minimum weight. · P2 motorcycle engines: Stock restrictor 36.5mm to 35mm, modified 37.5mm to 34mm; B.5 restrictor 37.5mm to 33mm. All weights increase 25 lbs. · T1-LP Chevrolet Camaro 1LE 2016- weight drops to 3500 lbs, restrictor increases to 70mm flat plate. · Ford Mustang Challenge returns to T1 as E&O, 4600 cc, 3300 lbs minimum, no restrictor. · T1 Chevrolet Corvette Cadillac XLR year range corrected from 04-09. · P2 cars limited to power application on maximum two wheels, effective 2019-07-01. · T1 Camaro, CTS, Firebird, GTO restrictor increases from 67mm to 70mm flat plate. · P2 Enterprise minimum weight increases to 1375 lbs; peak horsepower of sealed ESR engine reduced per CRB specification. · T2-T4 clarifies DOT tire requirements; must have minimum U speed rating and be DOT certified; touring spec line supersedes other rules. · Ford Mustang EcoBoost 3.5L classified in T1 at 3300 lbs minimum weight with 31mm restrictor. · T1 Corvette C5 body allowed C7 carbon aero parts, plus 50 lbs. · T1 Audi TTRS must conform to July 24th, 2015 revision 7 GTS rules instead of December 14th, 2011 revision 3. · T1 minimum ride height established at 3.5 inches, measured at rocker panel without driver. · T1 Porsche 928 S4/GTS-R minimum weight reduced to 3200 lbs, throttle restrictor removed. · Porsche 928 S4/928 GTS-R newly classified in T1 at 3500 lbs minimum with 60mm flat plate restrictor. · P2 stock engine restrictor shrinks to 35.0mm and weight rises to 1025 lbs; modified engine restrictor to 34.0mm, weight to 1125 lbs; line B.5 restrictor to 33.0mm, weight to 1185 lbs. · P2 Line A.1 restrictor reduced from 40mm to 38mm. · T1-LP Ford Mustang GT 5.0L 2018+ classified at 3400 lbs with 65mm flat plate restrictor. · FF Honda Fit permitted to use 0.25mm oversize pistons, cylinder honing increased to 73.315mm maximum. · FF heat shield rule clarified: thermal wrap allowed on manifold exterior if easily removable for inspection. · FF catch tank minimum capacity rules clarified: coolant catch tank now one U.S. pint minimum, oil catch tank one U.S. quart minimum. · P2 Spec Line cars now allow 1345cc Hayabusa stock engines at 1050 lbs with 30mm restrictor. · P2 Group CN Honda K20A-FD2 55mm restrictor implementation delayed from 1/1/2019 to 3/1/2019. · P2 Honda K20A-FD2 in CN chassis must use stock intake manifold with 64mm throttle body and 55mm restrictor at 1500 lbs minimum weight. · T1-LP Mustang GT350(R) spec line replaced with 2015+ model parameters including 5163cc engine, 3650 lbs curb weight, 315 tire size. · Ford Mustang FP350S (2018) classified in T1-LP at 3600 lbs with 18×11 wheels and 315 tires. · T1 suspension rules clarified: spherical bearings and bushings now explicitly permitted, alternate control arms allowed. · T1 Porsche 996 drops 200 lbs to 3000; 996 GT3 Cup drops 150 lbs to 3000; 997 drops 50 lbs to 3100. · Porsche 997 T1 Maximum now allows OEM PDK transmission alongside existing drivetrain options. · T1 Acura NSX Turbo World Challenge weight to 3100 lbs, restrictor to 44mm. · T1-T3 spec cars receive clarifications on permitted modifications, documentation requirements, and rule conformance; no performance changes.showhide
T1 Corrections to T1 Spec Lines #33678tyres & wheelsunclearGT4 McLaren 570S maximum tire size changes to 285 front, 315 rear.
P2 Request to Classify Sebeco NP01 #33378cars addedneutralSebeco NP01-EVO and Elan NP01 Mazda 2.0L MZR added to P2, 1600 lb minimum, no restrictor required.
P2 Radical spec line clarifications #33485wordingneutralP2 Radical SR3/SR4/Cup/Club Sport/Pro-Sport/PR6 removes assisted shifting requirement across all spec lines.
P2 E&O original class intent #33519wordingneutralP2 chassis rules clarified to allow composite materials in non-fully-composite construction; anti-intrusion panel attachment standardized; Stohr and converted F600 cars added with specific allowances.
P2 Update Engine Table Spec Line B.1 #33608engineunclearUnable to summarize: the change to P2 Engine Table Spec Line B.1 is not detailed in the provided text.
T1 GT4 section to Current T1 Rules. #33632cars addedneutralEight GT4 models added to T1 with weights from 3200 to 3575 lbs and restricted power per SRO 2022 rules.
T1 Correct Camaro Spec Line From Letter #30791 response to 3475lbs #32824weight -25 lbsfasterT1 Cadillac CTS/CTS-V, Chevrolet Camaro, Pontiac Firebird, Pontiac GTO 6162 OEM minimum weight reduced to 3475 lbs.
T1 Fix FP350S limited prep and Shelby 350 full prep issues #31680inductionfasterT1-LP Ford Mustang FP350S restrictor increases from 70mm to 75mm.
T1 Request to Classify AMG GT4 #32610cars addedneutralMercedes Benz AMG GT4 2017-2021 classified T1 Maximum at 3400 lbs minimum weight with HP-controlled SRO Power Level 2 engine.
P2 E&O Clarification of Chassis Construction Requirements #32469wordingneutralP2 chassis construction rules clarified: fully composite or partially composite requiring composite for mobility allowed; partial composite must roll without composite parts.
P2 Clean up P2 wording #32525wordingneutralP2 classification wording cleaned up in GCR section 9.1.8.C and Contents.
P2 After Market to Aftermarket #32373wordingneutralP2 Oldsmobile cam rules clarify aftermarket manufacturer requirements; wording only.
T1 Viper/Z06 Parity #31942weight -50 lbsfasterT1 Dodge Viper ACR displacement rises to 8400 OEM, minimum weight drops to 3550 lbs.
T1 Discrepancy in T1 allowances #32293wordingneutralT1 Limited T1 wording changed to clarify all T1 cars permitted specifications.
P2 Add spec line for Beasley B2 #32147cars addedneutralP2 adds Beasley B2 spec line with 1350 lbs, Mazda 12A, 40.5mm venturi, 16.5in wing.
P2 E&O Table 1 spec line wing terminology #32148wordingneutralP2 wing specs correct terminology from 'cord' to 'chord' for 16.5in single or dual element wings.
P2 E&O class name #32196wordingneutralP2 Converted F5 cars reclassified as Converted F500 cars; suspension must comply with F500 requirements, minimum width 55 inches.
P2 E&O Engine section #31969enginefasterP2 motorcycle engines increase to 1505cc max, two-stroke to 1205cc max; automotive engines gain 50 lbs minimum weight to 1350.
P2 E&O letter #31539 – Control Area definition #31783aeroslowerP2 Control Area definition narrowed; aerodynamic attachments and vertical structures like turning vanes now prohibited.
P2 BoP adjustment effective 1-1-22 #31538wordingunclearP2 Engine Table Spec Line B.1 changed effective 1-1-22, details not provided in excerpt.
P2 E&O clarification of "Control Area" definition #31539wordingneutralP2 Control Area definition clarified: floor extensions and aerodynamic attachments on bottom or top side now explicitly included.
T1 Turbo Miata Help #31315weight +200 lbsslowerT1 Mazda MX-5 Miata MazdaSpeed minimum weight rises to 2550 lbs, restrictor increases to 42mm.
T1 Fix the T1 Corvette heading #31528wordingneutralT1 Chevrolet Corvette Cadillac XLR classified for model years through 2019.
P2 P2 CN Engine Rebuild Clarification #31000wordingneutralP2 CN Honda K20A-FD2 engine rebuild rules clarified: machining prohibition replaced with specific restrictions on balancing, porting, polishing, valve jobs, cylinder honing.
P2 F5 P2 Conversion #30856aerofasterConverted F5 cars in P2 minimum width reduced to 55 inches from F5 spec.
P2 Clarify minimum body width requirement #30859wordingneutralP2 clarifies minimum body width requirement between front and rear wheels for Ralt RT40, RT41, Swift 008, 014.
T1 T1 E46 BOP E&O for Letter # 29970 #30934weight +100 lbsslowerT1 BMW E46/E36/Z3 minimum weight increases to 2700 lbs, 3.4L engine car to 2750 lbs.
T1 Request BoP for the Viper in 1 LP #29968inductionfasterT1 Dodge Viper SRT-10 restrictor increases from 45mm to 57mm.
T1 LS6 Alternative Head Question #30074wordingneutralT1 Chevrolet Corvette Cadillac XLR LS6 engine now permits Casting #799 heads with no other head modifications.
T1 T1-LP - Add Performance Pack, Bullet, Mach 1 to 18+ Mustang #29849inductionfasterT1 Ford Mustang Shelby/GT350/GT500 5.0L Coyote restrictor opens from 65mm to 70mm flat plate.
T1 Request BoP for the Viper in 1 LP #29968inductionfasterT1 Dodge Viper SRT-10 restrictor increases from 45mm to 57mm.
T1 Request to classify C7 and 13Viper in T1 LP #29969inductionfasterT1-LP Chevrolet Corvette C7 restrictor increases from 70 to 73 mm.
T1 Request LP Z06 steel chassis #30589wordingneutralT1-LP Corvette Z06 06-13 now allows aluminum chassis replacement with equivalent OE steel chassis.
P2 E&O tonneau cover provision in cockpit opening section #30459wordingneutralP2 tonneau covers now allowed to meet minimum dimensions; equipment attachment requirements clarified.
P2 Remove effective dates in Table 1 #30468wordingneutralP2 multiple chassis models remove effective dates from Table 1 specifications.
P2 E&O Maximum Valves Per Cylinder #30560engineneutralP2 engines limited to 4 valves per cylinder maximum across all three spec lines.
T1 Request For Reduction in Weight/Penalties for Camaro #30443weightfasterT1 Chevrolet Camaro with 6162 displacement minimum weight reduced to 3500 lbs.
T1 Fix dry sump Contradictions in T1-LP vs T2 #30596wordingneutralT1-LP Chevrolet Corvettes C5 Z06, C6 Grand Sport, and Z06 dry sump kit notes clarified to remove contradictions.
FF Kent crankshaft clarification #30426wordingneutralFF block relief permitted only as needed to fit allowed crankshaft.
P2 Add a new spec line for a 2-cycle, 3-cylinder engine up to 820cc #30272cars addedneutralP2 adds new spec line for 2-cycle 3-cylinder engine up to 820cc with 10 front and 14-15 rear wheel width.
T1 T1 LP Aero adjustments #30196aerounclearT1 LP removes 50 lbs weight allowance for stock headers, adds aero device allowance up to 100 lbs, permits headers.
T1 Request to Clarify Miller Mustang Classification #28728engineunclearT1 Ford Mustang Challenge 3-valve maximum displacement changes to 4600/5000.
T1 BMW E46 Carbon Dash #29806weightslowerT1 BMW E46 now allows carbon or fiberglass OEM-style dashboards with 25 pound penalty.
T1 Request to Update T1 Mustang Spec Line #30001wordingneutralT1 Ford Mustang/Thunderbird limited to Shelby/Shelby GT350/GT500 models through 2018.
T1 Class BMW M2CS Club Sport #30195cars addedneutralBMW M2CS Club Sport classified in T1-LP Spec Lines effective 2021-02-01.
T1 997.1 GT3 Cup #30229cars addedneutralPorsche 997.1 GT3 Cup (2006-2011) classified in T1 at 3600cc, 3150 lbs minimum weight.
T1 Correct T1 Limited Prep Years #29708wordingneutralT1 Chevrolet Corvette Z06 years extended from 06-12 to 06-13.
FF Allow Optional Coolant Bleed Line to Correct a Known Problem #29673wordingneutralFF class cylinder head may now have optional coolant bleed line fitting to top of head for air release.
FF Clarification regarding Honda LC1 ECU implementation date #29684wordingneutralFF Honda LC1 ECU by HPD permitted effective 12/1/2020, must use HPD lambda sensor.
P2 Balance of Performance adjustments effective 01-01-2021 #29822inductionfasterP2 Honda K20A-FD2 intake restrictor reduced from 55mm to 50mm, making cars faster.
T1 Changes to Corvette C8 #29898tyres & wheels -100 lbsfasterT1 Corvette C8 Z51 gets wider wheels and tyres, weight drops 100 lbs to 3550.
P2 E&O clarification of P2 rear wing requirements #29205aeroneutralP2 rear wing requirements clarified: standard wing 6×12 inches, end plates 14-inch square; alternate 110cm width wing 9×18 inches, end plates 14×18 inches.
FF Clarification regarding Honda LC1 ECU implementation #29135wordingneutralFF Honda LC1 ECU implementation date changed from 3/1/2020 to pending availability of support materials.
P2 Classify Elan NP01 in P2 Table 1 #28812cars addedneutralElan NP01 classified in P2 Table 1 as Spec Line car with 2000cc displacement and P2 Engine Table restrictor.
T1 Consider coil spring conversion Corvette in T2 #28824suspension & brakesneutralT1 and T2 Corvettes may convert leaf spring suspension to coilover with 800 lb max spring rate allowed.
P2 SCCA Enterprises ESR / P2 engine restrictor testing #28669engineneutralP2 Enterprises Sports Racer adds 55mm flat plate intake restrictor Part # WM303013 as alternative to SIR.
T1 Additional Clarification on 996 Cup in T1 From Letter #28040 #28060wordingneutralT1 Porsche 996 GT3 Cup eligible model years changed from 2002-2005 to 1998-2004.
T1 Request SPEC Corvette Rear Spolier #28182aeroneutralT1 Corvette and Cadillac XLR permitted to install SCRSPLR-001 rear spoiler with OE bodywork.
T1 T1 Rear Brake Rotor Size Exemption for Gen 5 Camaro #28402wordingneutralT1 Gen 5 Camaro allowed 366mm OEM rear rotor and caliper without weight penalty.
FF E&O FF Kent Engine alternator language #28204wordingneutralFF alternator changes from not required to optional.
P2 Add ESR inlet restrictor #27869inductionslowerP2 Enterprise Sports Racer 2.3L engine now requires SIR or Flat Plate restrictor sized in 0.5mm increments.
T1 Request 996 GT3 Trunk for Wing Allowance. #28153wordingneutralT1 Porsche 996 Spec Lines now allows 996 Cup Replica Rear deck lid.
T1 All Touring, Change DOT Tire Language 9.1.9.1, 9.3.45 #28452wordingneutralT1 Acura NSX Turbo World Challenge and Audi TTRS GTS 2011 now require DOT tires per GCR section 9.3.
FF Honda Racing HPD low cost ECU proposal #27563engineneutralFF allows Honda HPD LC1 low-cost ECU with lambda sensor; E1 ECU no longer supported but existing units permitted if sealed.
FF Update rain tire designation #28443tyres & wheelsneutralFF rain tyres now allow Hoosier W3 Radial in addition to existing Hoosier Wet option.
P2 Request for Fly by Wire Rule Wording Change #28247wordingneutralP2 fly-by-wire throttle control wording clarified: stock ECUs with drive-by-wire must activate original throttle shaft mechanism.
T1 Request for E46 wagon with S54 engine in T1 #27427wordingneutralT1 BMW E46 wagon with S54 engine allowed; displacement corrected from 3200 to 3250cc.
T1 Request to include Subaru WRX/STI 02-18 in T1 #24916cars addedneutralT1 adds Subaru WRX/WRX STI 2005-2020 at 3000 lbs minimum weight with 46 mm restrictor.
T1 Request Ford Mustang FP350S T1-LP weight and restrictor change #26662weight +100 lbsslowerT1 Ford Mustang GT (15-17) and GT5.0L (2018-) weight raised to 3500 lbs; Brembo BBK 380mm now at no penalty; restrictors removed from notes.
T1 Request to classify Ford Coyote 3rd Gen OEM #27145cars addedslowerT1 Ford Mustang/Thunderbird 5000 Coyote OEM reclassified to include 2015–2017 and 2018+ model years with 65mm restrictor for 18+.
T1 Request alternate dashboard #27276weightslowerT1 BMW M3 E92 carbon dash allowed with 25 lb penalty.
T1 Request for Allowance of Coil Springs on Limited Prep C6 Corvette #27713suspension & brakesfasterT1 Corvette C5 Z06, C6 coupe, C6 Grand Sport, and Z06 may convert leaf springs to conventional coilover suspension.
P2 Request for addition of BMW Engine in P2 Engine Table #27821cars addedneutralP2 adds BMW to motorcycle-based engine options in 4-cycle line alongside Kawasaki, Suzuki, Yamaha, Honda.
P2 Update Engine Table Line E notes #27414inductionslowerP2 Honda K20A-FD2 non-composite chassis must use 55mm flat plate intake restrictor at 1500 lbs minimum weight.
P2 Update P2 Engine Table spec lines to reflect 3/1/2019 #27254inductionslowerP2 motorcycle engines: Stock restrictor 36.5mm to 35mm, modified 37.5mm to 34mm; B.5 restrictor 37.5mm to 33mm. All weights increase 25 lbs.
T1 T1 LP 2016 Camaro and Later #27198weight -100 lbsfasterT1-LP Chevrolet Camaro 1LE 2016- weight drops to 3500 lbs, restrictor increases to 70mm flat plate.
T1 Request to return Ford Mustang Challenge Car to T1 #26751cars addedneutralFord Mustang Challenge returns to T1 as E&O, 4600 cc, 3300 lbs minimum, no restrictor.
T1 Correct years in T1 FP Corvette spec #27023wordingneutralT1 Chevrolet Corvette Cadillac XLR year range corrected from 04-09.
P2 E&O Transmissions #27006otherslowerP2 cars limited to power application on maximum two wheels, effective 2019-07-01.
T1 Request BoP Baten - T1 Camaro - Follow up to Letter # 26145 #26900inductionfasterT1 Camaro, CTS, Firebird, GTO restrictor increases from 67mm to 70mm flat plate.
P2 Request to restrict all cars #26246weightslowerP2 Enterprise minimum weight increases to 1375 lbs; peak horsepower of sealed ESR engine reduced per CRB specification.
T1 Clarify DOT tires touring #26556tyres & wheelsneutralT2-T4 clarifies DOT tire requirements; must have minimum U speed rating and be DOT certified; touring spec line supersedes other rules.
T1 Request to Classify EcoBoost Mustang #25841cars addedneutralFord Mustang EcoBoost 3.5L classified in T1 at 3300 lbs minimum weight with 31mm restrictor.
T1 Request Corvette aerodynamic aids #26265aeroslowerT1 Corvette C5 body allowed C7 carbon aero parts, plus 50 lbs.
T1 Audi TTRS VTS Documentation Revision #26578wordingunclearT1 Audi TTRS must conform to July 24th, 2015 revision 7 GTS rules instead of December 14th, 2011 revision 3.
T1 Request Ride Height Clarification #26599wordingneutralT1 minimum ride height established at 3.5 inches, measured at rocker panel without driver.
T1 Request to classify the Porsche 928GTS/S4 in Touring 1 #26315cars addedneutralPorsche 928 S4/928 GTS-R newly classified in T1 at 3500 lbs minimum with 60mm flat plate restrictor.
P2 Change Engine Table Lines B.1 & B.5 #25777inductionslowerP2 stock engine restrictor shrinks to 35.0mm and weight rises to 1025 lbs; modified engine restrictor to 34.0mm, weight to 1125 lbs; line B.5 restrictor to 33.0mm, weight to 1185 lbs.
P2 Change Line A.1 restrictor size #26429inductionslowerP2 Line A.1 restrictor reduced from 40mm to 38mm.
T1 Request Mustang GT Limited Prep 2018 Classification #24431cars addedneutralT1-LP Ford Mustang GT 5.0L 2018+ classified at 3400 lbs with 65mm flat plate restrictor.
FF Request for Oversize Honda Fit Pistons #25810enginefasterFF Honda Fit permitted to use 0.25mm oversize pistons, cylinder honing increased to 73.315mm maximum.
FF Heat Shield - Fit Intake #26102wordingneutralFF heat shield rule clarified: thermal wrap allowed on manifold exterior if easily removable for inspection.
FF Request catch cans/tanks clarification #26158wordingneutralFF catch tank minimum capacity rules clarified: coolant catch tank now one U.S. pint minimum, oil catch tank one U.S. quart minimum.
P2 Request to Allow 1345cc Hayabusa Engines for Spec Line P2 Cars #25595enginefasterP2 Spec Line cars now allow 1345cc Hayabusa stock engines at 1050 lbs with 30mm restrictor.
P2 Change CN inlet restrictor implementation date #25816wordingneutralP2 Group CN Honda K20A-FD2 55mm restrictor implementation delayed from 1/1/2019 to 3/1/2019.
P2 Clarify Honda K20A-FD2 parts requirement #25950inductionslowerP2 Honda K20A-FD2 in CN chassis must use stock intake manifold with 64mm throttle body and 55mm restrictor at 1500 lbs minimum weight.
T1 Class 2015+ Mustang GT350(R) #21466wordingneutralT1-LP Mustang GT350(R) spec line replaced with 2015+ model parameters including 5163cc engine, 3650 lbs curb weight, 315 tire size.
T1 Request to Classify Ford FP350S in T1-LP #25341cars addedneutralFord Mustang FP350S (2018) classified in T1-LP at 3600 lbs with 18×11 wheels and 315 tires.
T1 Amendment to Request #25555 #25556wordingneutralT1 suspension rules clarified: spherical bearings and bushings now explicitly permitted, alternate control arms allowed.
T1 Request to balance 996 v 997 T1 weight #25658weightfasterT1 Porsche 996 drops 200 lbs to 3000; 996 GT3 Cup drops 150 lbs to 3000; 997 drops 50 lbs to 3100.
T1 Request to Add PDK Transmission to 997 Porsche Spec Line #25668wordingneutralPorsche 997 T1 Maximum now allows OEM PDK transmission alongside existing drivetrain options.
T1 T1 World Challenge/Grand AM Spec Cars #25687weightslowerT1 Acura NSX Turbo World Challenge weight to 3100 lbs, restrictor to 44mm.
T1 Add Clarification to Spec Car Classifications Vehicle Spec #25774wordingneutralT1-T3 spec cars receive clarifications on permitted modifications, documentation requirements, and rule conformance; no performance changes.
Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of P2" is the class's best as a share of P2's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when P2's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.