FF + SRF3 + FC at Buttonwillow Raceway Park

2023-03-01 SRF3 Update SRF Brake Rule

#33469 from Robey Clark · Rule change · TB 23-01 (2023-01 Fastrack)

In SRF, GCR section 9.1.8.D.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no
machining of any kind. Minimum thickness 12.20mm (0.481"). The 1985 Renault Alliance solid front rotor (Reference: Bendix
PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type
rotor. The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N
1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other
modification allowed. Wilwood caliper with bracket universal fit P/N 800038 may be used as delivered with no modification of
any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind;

A specification table follows in the original; it is not shown here.

2023-03-01 FF Add Fast Forward Part Numbers for Honda Fit Engine

#33752 from Formula/Sports Racing Committee · Rule change · TB 23-03 (2023-03 Fastrack)

In FC/FF, GCR section 9.1.1.B.14.a.6, change as follows:
"For all Honda part numbers in these specifications, superc seding part numbers are considered equivalent.
In FC/FF, GCR section 9.1.1.B.14.f.5, change as follows:
"Cylinder head breather restrictor must be used as supplied by HPD or Fast Forward, unmodified.: HPD PN: 15262-F21S-A200; Fast
Forward PN: FF200-503."
In FC/FF, GCR section 9.1.1.B.14.k.2, change as follows:
"The upper manifold, air box and throttle body assembly must be used as delivered from Honda, HPD, or Fast Forward as noted
below."

2023-03-01 SRF3 Update SRF Bodywork Fitment Rule

#33765 from Robey Clark · Rule change · TB 23-03 (2023-03 Fastrack)

In Spec Racer Ford, GCR section 9.1.8.D.1.E, change as follows:
"j. Optional Bodywork Modification:
Viewing the tail section of the car from behind, draw a vertical line at the left and right ends of the outer vents from the bottom
edge of the bodywork up to a point two (2) inches below the crease at the lower edge of the vented panel. Make a vertical cut at
each line. The horizontal cut is to be one (1) inch below the crease at the base of the vented panel. Leave a one (1) inch radius at
each corner. Air Scoop (P/N 190000) must be installed in conjunction with rear cutout per Enterprises installation instructions.
SRF3 tail sections are allowed on SRFs. For purposes of tail section to center section fitment with the GEN3 airbox, shimming is
allowed at the rear of the center section. Shim material may be up to 19 mm (0.75") thick along the 1" upper square sidepod

2023-05-01 SRF3 Update SRF Front W2 Rain Tire Part Number

#34118 from Robey Clark · Rule change · TB 23-05 (2023-05 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Front – Hoosier P/N 46100 1 P185/65R13 W2"

2023-06-01 SRF3 Hoosier SRF Wet Front Tire Rule Update

#34189 from Robey Clark · Rule change · TB 23-06 (2023-06 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."

2023-06-01 FC USF2000 Van Diemen with Mazda MZR LF-DE 2.0L in FC

#34329 from Formula/Sports Racing Committee · Rule change · TB 23-06 (2023-06 Fastrack)

RM 23-07, USF2000 Van Diemen with Mazda MZR LF-DE 2.0L in FC, GCR section 9.1.1.B.1, add a new section and re-letter the
following sections accordingly:
"c. The USF2000 tube frame Van Diemen car powered by the Mazda MZR LF-DE 2 liter engine is added as a "spec line" car in
Formula Continental. Additional "spec line" cars are disfavored, and Balance of Performance (BoP) adjustments to keep "spec
line" cars competitive with cars that meet the class formula are likewise disfavored."
In FC, GCR section 9.1.1.B.11, add the following:
"The only permitted engines are:
a. The Ford 2 liter single overhead camshaft "NE" series engine or the 1971-74 Pinto/Capri 2 liter single overhead camshaft

A specification table follows in the original; it is not shown here.

2023-07-01 FC Review FC Runoffs Tire Marking Rule

#34274 from SCCA Staff · Rule change · TB 23-06 (2023-05 Fastrack)

In FC, GCR section 9.1.1.B.10.h, change as follows:
"FC shall be is permitted a maximum of four (4) dry tires and four (4) wet tires for all Regional, Major, and Super Tour events;
eight (8) dry tires and eight (8) wet tires are permitted for the Runoffs. This rule shall be is effective beginning with the first (1st)
qualifying session of the event. Marked tires are not required for testing or practice. It is the competitor's responsibility to
ensure that the tires are declared, marked, and logged by Tech in advance of the tire(s) being used in a qualifying session or
race. Failure to participate on marked tires will result in a penalty.
1. Use of an undeclared tire shall automatically result in all times being disallowed in that session or finishing position in that
race.

2023-10-01 SRF3 SRF Radiator Rule Update

#34805 from Robey Clark · Rule change · TB 23-10 (2023-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.V.j, change as follows:
"Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be
replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent,
as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed
even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."

2024-01-01 SRF3 Update SRF Rain / Brake Rule

#34706 from Robey Clark · Rule change · TB 23-09 (2023-09 Fastrack)

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with
incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes
GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the
wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain
light."

2024-01-01 SRF3 Update SRF Brake Light Rule v1

#34853 from Robey Clark · Rule change · TB 23-10 (2023-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the
original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No
changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake
Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as
a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."

2024-01-01 FC Please correct omitted punctuation

#34890 from Club Racing Board · Rule change · TB 23-10 (2023-09 Fastrack)

In Cars and Equipment, GCR section 9.3.33.B.2, add the following:
"(Effective 1/1/2024) A red taillight meeting FIA Standard 8874-2019, Technical List No. 76, is required on all Formula (open
wheel) and Sports Racing cars."
In Appendix F. Technical Glossary, Minimum Weight, change as follows:
"Minimum Weight: – Weight specified with driver, exactly as they come off the race circuit, at the conclusion of any race or
qualifying session."
In FA Table 1, Spec Line E notes, add the following:
"Any BD series iron or alloy cylinder block and alternate crankshaft permitted."

2024-01-01 SRF3 SRF / SRF3 Rule Updates

#35268 from Robey Clark · Rule change · TB 24-01 (2024-01 Fastrack)

In SRF, GCR section 9.1.8.D.1.H, add the following:
"NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any
flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part
# P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to
improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting
support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad
"anti-rattle" clips must be removed."
In SRF, GCR section 9.1.8.D.1.V, add the following:

2024-01-01 FF Honda Fit Oversize Piston Rings

#35305 from Doug Learned · Rule change · TB 24-01 (2024-01 Fastrack)

In FF, GCR section 9.1.1.B.14.e.3.a, add the following:
"The standard ring pack, PN 13011-RB1-004 (Riken) or 13011-RB1-006 (Nippon), or the oversize ring pack, PN 13021-RB7-Z01
(Riken), or 13021-RB7-Z02 (Nippon), or FF800-100 (Fast Forward), may be used."

2024-04-01 FC Four Pot Calipers

#35481 from Steve Jenks · Rule change · TB 24-04 (2024-04 Fastrack)

In FC Table FC Charts, add the following:
In FC, GCR section 9.1.1.B.1.c, change as follows:
"The USF2000 tube frame Van Diemen car powered by the Mazda MZR LF-DE 2 liter engine and the F2000 Metrik ZF2 car
equipped with 4-piston calipers is are added as a "spec line" cars in Formula Continental. Additional "spec line" cars are
disfavored, and Balance of Performance (BoP) adjustments to keep "spec line" cars competitive with cars that meet the class
formula are likewise disfavored."
FC Charts
Car Engine Wheel Width

A specification table follows in the original; it is not shown here.

2024-06-01 SRF3 SRF3 Alternator Pulley Update In

#36095 from Robey Clark · Rule change · TB 24-06 (2024-06 Fastrack)

SFR3, GCR section 9.1.8.D.2.H.17, change as follows:
"Alternator Pulley: P/N G902130, or P/N G902130A, or P/N G902131 (six row). 12 11 oz minimum weight."

2024-08-01 SRF3 Update Rain Tire Rule and Hoosier Decal Placement

#36436 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used.
OR
Front – Hoosier P/N 46101 P185/65R13 W2
Rear – Hoosier P/N 46105 P205/60R13 W2

2024-09-01 SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info

#36624 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows:
"Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose
to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1)
decal must be located on each side of the car and one (1) decal must be visible on the front."

2024-10-01 FF Update to FF EGR Blanking Plate Rule

#36633 from Matt Boian · Rule change · TB 24-10 (2024-10 Fastrack)

In FF, GCR section 9.1.1.B.14.r.1, change as follows:
"All emission control devices must be removed and blocked off by the blanking plate provided by HPD or Fast Forward as noted
below, except for the VTEC activation valve. The VTEC activation valve must be retained; and it must be functioning. No
modifications are permitted.
a. EGR Plate: Fast Forward PN: FF200-301.
b. EGR Port Cover: Fast Forward PN: FF200-302."

2024-10-01 SRF3 Update SRF3 Air Filter Rule

#36681 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.H.23, change as follows:
"Air Filter: P/N WM301020 or K&N RC-9160"

2024-10-01 SRF3 Update SRF Brake Rotor Thickness

#36687 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with
no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."

2024-10-01 SRF3 Hoosier Tire Decal Placement

#36739 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.B, change as follows:
"Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the
nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."

2024-11-01 FC 9.1.1.10.h. FC Tire Rule

#36533 from SCCA Staff · Rule change · TB 24-09 (2024-09 Fastrack)

In FC, GCR section 9.1.1.B.10.h, change as follows:
"(Effective 11/1/2024) FC is permitted a maximum of four (4) dry tires and four (4) wet tires for all Regional, Major, and Super
Tour events; eight (8) dry tires and eight (8) wet tires are permitted for the Runoffs. This is effective beginning with the first (1st)
qualifying session of the event. Marked tires are not required for The tire limit does not apply to testing or practice. It is the
competitor's responsibility to ensure that the tires are declared, marked, and logged by Tech immediately upon conclusion of the
first qualifying session, as provided in the event supplemental regulations, or per the instructions of the Race Director or Chief
Steward. in advance of the tire(s) being used in a qualifying session or race. Failure to participate on marked Use of tires in
excess of the number allowed will result in a penalty. Failure to participate on declared/marked/logged tires after the time

2024-11-01 FF Change FF/FC Weight with Sequential Gearbox

#36651 from Robert Wright · Rule change · TB 24-11 (2024-11 Fastrack)

In FF, GCR section 9.1.1.B.20.A.3, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
In FC, GCR section 9.1.1.B.20.B.4, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."

2024-11-01 FC Change FF/FC Weight with Sequential Gearbox

#36651 from Robert Wright · Rule change · TB 24-11 (2024-11 Fastrack)

In FF, GCR section 9.1.1.B.20.A.3, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
In FC, GCR section 9.1.1.B.20.B.4, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."

2024-11-01 FF Alternative Oversize Honda Fit Pistons

#37064 from Formula/Sports Racing Committee · Rule change · TB 24-11 (2024-11 Fastrack)

In FF, GCR section 9.1.1.B.14.e.1, change as follows:
"Honda Fit OEM standard size pistons, PN: 13010-RB1-000, or Honda Fit OEM 0.25mm oversize pistons, PN: 13020-RB7-Z00, or
Fast Forward 0.25mm oversize pistons, PN: FF800-110, may be used."
In GCR section 9.1.1.B.14.e.2, change as follows:
"a. Maximum standard piston diameter, measured at a point 16mm from the bottom of the skirt: 73.240mm
(2.8834 2.8835 inches).
b. Centerline of wrist pin to crown maximum: 26.21mm (1.032 inches).
c. Maximum overall height from skirt to crown edge: 47.80mm (1.882 inches).

2025-03-01 FF Formula F Proposal to Invite Older Cars Via a Tire Rule Change

#37802 from Anthony Stefanelli · Rule change · TB 25-03 (2025-03 Fastrack)

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Formula F shall be limited to the following tires (front tires may not be used as rears):
Dries:
Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13
Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13
Wets:
Front - Hoosier Wet or W3 Radial 44421 185/60R13
Rear - Hoosier Wet or W3 Radial 44426 205/60R13

2025-04-01 SRF3 Driver Safety & Comfort

#37966 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.1.D, add the following:
"f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

2025-04-01 SRF3 Update SADEV transmission specs

#37992 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.2.K, change as follows:
"OR
SADEV-SRF3 6-Speed Sequential (beginning from Oct. 4, 2021 onward):
1st 12-36 3.0000 : 1
2nd 15-31 2.0667 : 1
3rd 18-28 1.5556 : 1
4th 22-28 1.2727 : 1
5th 24-26 1.0833 : 1

2025-05-01 FF Page 228, FF tire rule 9.1.1.10.e

#38251 from Anthony Stefanelli · Rule change · TB 25-05 (2025-05 Fastrack)

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Formula F shall be limited to the following tires (front tires may not be used as rears):
Dries:
Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13
Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13
Wets:
Front - Hoosier Wet or W3 Radial 44421 185/60R13
Rear - Hoosier Wet or W3 Radial 44426 205/60R13

2025-09-01 SRF3 SRF Rule Updates

#38853 from Robey Clark · Rule change · TB 25-09 (2025-09 Fastrack)

Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following:
"SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil
Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no
machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber
caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced
with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038

2025-10-01 SRF3 Add HD Oil Cooler

#38979 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.V.ff, change as follows:
"SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan
permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."

2026-01-01 FC F2000 MZR Spec Line Clarity/Revision Requested

#38927 from Rock Beauchamp · Rule change · TB 26-01 (2026-01 Fastrack)

In FC Charts table, USF2000 Tube Frame spec line, add the following to the Notes:
"Cars originally built with the Hewland LD200 4-speed H-pattern may use that transmission as an alternative to the Hewland JL-
200 5-speed sequential transmission."

2026-01-01 FF Formula F Alternative Tire Rule Proposed Clarifications

#39281 from Jay Messenger · Rule change · TB 26-01 (2026-01 Fastrack)

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Alternatively, Formula F cars with rocker arm suspension (e.g., 1987-90 Reynard, Swift DB1,) and/or outboard suspension on at
least one chassis end homologated in 1989 or earlier with any combination of rocker arm or outboard suspension on all four
corners (e.g., 1987 – 1990 Reynard, Swift DB1) may use the following alternative tires. Note: This rule is intended to allow older
cars with the described suspension design to use the alternative tires. It is not to be exploited by modifying cars with push-rods or
pull-rods to meet the above requirements or by modifying either end of older cars to push- or pull-rod suspension to be eligible to
run the alternative tires. Cars that were homologated in 1989 or earlier with push- or pull-rod suspension on no more than two
corners may seek approval to run the alternative tire by utilizing the compliance process outlined in GCR section 8.1.4."

2026-01-01 FC Adjust F2000 Metrik ZF2 weight

#39612 from Club Racing Board · Rule change · TB 26-01 (2026-01 Fastrack)

In FC Charts table, F2000 Metrik ZF2 spec line, change the Weight as follows:
"1240 1220"