This track has been raced on 2 configurations (The Circuit, 2.57 mi; 2.92 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
2 runs are left out as not that car's own laps (far quicker than the car managed in any other session and than anyone else in its class all week; usually a swapped transponder): Tom Burt in Cal Club 2025 PM (1:42.300; the car's best in any other session was 1:52.334 and the rest of the class's best all week 1:50.233); Thomas Lepper in Cal Club 2026 Grp 1 EP FP HP B-Spec Race 1 (1:42.146; the car's best in any other session was 2:12.311 and the rest of the class's best all week 2:09.353).
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Glamdring
FV
1
1:44.706Mark Edwards
2:05.638Mark Edwards
2:04.892Mark Edwards
128.9Mark Edwards
28.863Mark Edwards
30.228Mark Edwards
45.501Mark Edwards
SCCA Ent SRF3
SRF3
38
1:50.233Caleb Shrader
1:50.233Caleb Shrader
1:50.825Caleb Shrader
138.9Paul Marino
30.136Caleb Shrader
31.672Caleb Shrader
44.841Tom Burt
Caracal C1
FV
1
1:51.773Marjorie Lundberg
2:04.579Marjorie Lundberg
2:02.255Marjorie Lundberg
122.3Marjorie Lundberg
30.462Marjorie Lundberg
32.246Marjorie Lundberg
49.106Marjorie Lundberg
DART II
FV
1
1:58.898Mace Gjerman
2:04.535Mace Gjerman
1:58.898Mace Gjerman
121.9Mace Gjerman
26.541Mace Gjerman
35.132Mace Gjerman
55.126Mace Gjerman
Protoform P4
FV
1
2:01.197Gavin Sweeney
2:02.354Gavin Sweeney
2:01.197Gavin Sweeney
124.6Gavin Sweeney
32.871Gavin Sweeney
34.423Gavin Sweeney
53.607Gavin Sweeney
LYNXX
FV
1
2:02.715Donald Manthe
2:06.541Donald Manthe
2:05.686Donald Manthe
117.9Donald Manthe
32.587Donald Manthe
35.402Donald Manthe
54.322Donald Manthe
Crusader
FV
1
2:04.723Blake Tatum
2:05.855Blake Tatum
2:04.723Blake Tatum
122.5Blake Tatum
34.149Blake Tatum
35.231Blake Tatum
55.343Blake Tatum
Mysterian M2
FV
1
2:06.510Ronnie Chuck
2:08.877Ronnie Chuck
2:06.510Ronnie Chuck
115.9Ronnie Chuck
33.255Ronnie Chuck
35.637Ronnie Chuck
56.197Ronnie Chuck
Mini Cooper
B-Spec
2
2:09.353Trenton Kramer
2:09.353Trenton Kramer
2:09.916Trenton Kramer
121.5Trenton Kramer
34.887Trenton Kramer
37.301Trenton Kramer
56.951Trenton Kramer
Mazda 2
B-Spec
3
2:10.149Ali Naimi
2:11.287Ali Naimi
2:10.149Ali Naimi
117.2Ali Naimi
34.986Ali Naimi
37.336Ali Naimi
57.011Ali Naimi
Toyota Yaris
B-Spec
1
2:10.513Joseph Gersch
2:10.513Joseph Gersch
2:10.749Joseph Gersch
118.3Joseph Gersch
35.332Joseph Gersch
37.456Joseph Gersch
57.202Joseph Gersch
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
B-Spec BOP Adjustment for Yaris iA, 2020+ Versa, and 07-08 Honda Fit
#35382 from Matt Wolfe · Rule change · TB 24-03 (2024-03 Fastrack)
fasterB-Spec Honda Fit 07-08 loses 125 lbs to 2400; Versa S 2020+ loses 150 lbs to 2550; Yaris iA 16-20 loses 250 lbs to 2450.
In B-Spec Spec Lines, Honda Fit (07-08), change as follows: Min weight: "2525 2400" Notes: "Any Cold Air Intake Package allowed (any manufacturer). This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Honda Fit (07-08) Automatic, change as follows: Min weight: "2525 2400" Add to Notes: "Any Cold Air Intake Package allowed (any manufacturer). This configuration is not currently eligible for Runoffs
Show 12 more lines
competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Nissan Versa S (2020-), change as follows: Min weight: "2700 2550" Add to Notes: "This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Toyota/Scion IA Sedan (16-20), change as follows: Min weight: 2700 2450" Add to Notes: "This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted."
neutralB-Spec Honda Fit 07-08 rear sway bar part number changed to Progress #62.1060.
In B-Spec Spec Lines, Honda Fit (07-08) Automatic, change Notes as follows: "Allow rear sway bar Progress # 62.1061 0." In B-Spec Spec Lines, Honda Fit (07-08), add to Notes the following: "Allow rear sway bar Progress # 62.1060."
B-Spec Change restrictor from 30mm to 31mm (2015+ Honda Fit) and add 50#
#34857 from Matt Downing · Rule change · TB 24-04 (2024-04 Fastrack)
fasterB-Spec Honda Fit MT 2015-19 restrictor increases 30mm to 31mm, weight rises 2525 to 2550 lbs.
In B-Spec Spec Lines, Honda Fit MT (15-19), change as follows: Weight: ""2525 2550" Notes: "30 31mm" In B-Spec Spec Lines, Honda Fit MT (15-19), change as follows: Weight: ""2525 2550" Notes: "30 31mm"
B-Spec Wheel Offset and Spacer Revision
#35466 from Kent Carter · Rule change · TB 24-04 (2024-04 Fastrack)
fasterB-Spec and C-Spec now permit wheels of any offset if tire doesn't protrude beyond fender; spacers allowed with differing left-right offsets per axle.
In GCR, Section 9.1.10.E.8., change as follows: "Wheels: All wheels shall be one-piece metal castings or metal two piece welded. Wheels of any offset are permitted provided the tire tread (the portion of the tire that contacts the ground) does not protrude beyond the fender opening when viewed from the top perpendicular to the ground. Wheel spacers and aftermarket wheel studs/bolts are permitted. Wheel bolts may be replaced with studs and nuts. Total offset must be the same left to right for an individual axle but may differ from front to rear. For B-Spec Required wheel/rim diameter is fifteen inches (15”). Maximum wheel/rim width is seven inches (7”). Minimum Wheel/rim weight shall be 13 lbs. For C-Spec Required wheel/ rim diameter is seventeen inches (17”). Maximum wheel/rim width is eight inches (8”). Minimum
Show 3 more lines
Wheel/rim weight shall be 17 lbs. All wheels shall be one-piece metal castings or metal two piece welded. All four wheels must be the same dimensional offset. Aftermarket wheel studs and/or wheel bolts are allowed. Wheel bolts may be replaced with studs and nuts. Wheel spacers are allowed, the same thickness spacer must be used on all four corners. "
neutralB-Spec Mini Cooper Countryman R60, Paceman R61, and Nissan Versa 1797cc spec lines expire 1/1/2025 unless appealed by 12/1/2024.
In B-Spec Spec Lines, Mini Cooper Countryman (R60) (11-16), add to Notes the following: ”**This Spec line will expire 1/1/2025 unless an appeal is filed on or before 12/1/2024.**” In B-Spec Spec Lines, Mini Cooper Paceman (R61) (11-16), add to Notes the following: ”**This Spec line will expire 1/1/2025 unless an appeal is filed on or before 12/1/2024.** ” In B-Spec Spec Lines, Nissan Versa (07-11) with 1797cc engine, add to Notes the following: ”**This Spec line will expire 1/1/2025 unless an appeal is filed on or before 12/1/2024.** ”
Applies to Mini Cooper on this page: Trenton Kramer, Thomas Lepper
B-Spec Delete trim levels/update language for spec lines
neutralB-Spec model descriptions standardized: trim levels and door count designations removed or replaced with body style wording.
In B-Spec Spec Lines, change Model description as follows: "Chevrolet Sonic 4dr Sedan MT (12-19)" "Chevrolet Sonic 4dr Sedan AT (12-19)" "Chevrolet Sonic 5dr Hatch Hatchback MT (12-19)" "Chevrolet Sonic 5dr Hatch Hatchback AT (12-19)" "Ford Fiesta 5dr Hatchback (11-19)" "Ford Fiesta 4dr Sedan (11-19)" "Honda Fit MT (07-08)"
Show 7 more lines
"Honda Fit Automatic AT (07-08)" "Honda Fit MT (09-14)" "Hyundai Accent GS Hatchback (12-19)" "Kia Rio 5-door/LX Hatchback (12-19)" "Nissan Versa S (2020-)" "Toyota Yaris Hatchback (07-11)" "Toyota Yaris Hatchback (12-18)"
neutralB-Spec and C-Spec wheels must be same thickness spacers all four corners; wording clarified on offset and protrusion rules.
In GCR, Section 9.1.10.E.8., change as follows: "Wheels: All wheels shall be one-piece metal castings or metal two piece welded. All four wheels must be the same dimensional offset. Any offset is permitted so long as Wheels of any offset are permitted provided the tire tread (the that portion of the tire that contacts the ground) does may not protrude beyond the fender opening when viewed from the top perpendicular to the ground. Wheel spacers and aA ftermarket wheel studs/ and or wheel bolts are permitted allowed. Wheel bolts may be replaced with studs and nuts. Wheel spacers are allowed, but must be the same thickness on all four corners.Total offset must be the same left to right for an individual axle but may differ from front to rear. B-Spec Required wheel/rim diameter is fifteen inches (15”). Maximum wheel/rim width is seven inches (7”). Minimum
Show 5 more lines
Wheel/rim weight shall be 13 lbs. C-Spec Required wheel/rim diameter is seventeen inches (17”). Maximum wheel/rim width is eight inches (8”). Minimum Wheel/rim weight shall be 17 lbs. Wheels are permitted any offset provided the tire tread (that portion of the tire that contacts the ground) does not protrude beyond the fender opening when viewed from the top perpendicular to the ground."
neutralB-Spec Mazda2 and multiple Mini Cooper models eliminate redundant sway bar end link part number notes.
B-SPEC Spec Lines, elimination from Notes the following: Mazda2 (10-14): "Front sway bar end links adjstbl 0000-04-2202," Mini Cooper Hatchback (R50) MT (02 - 06): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Hatchback (R50) CVT (02 - 06): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper (R56) MT (07-10): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed."
Show 16 more lines
Mini Cooper (R56) AT (07-10): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Clubman (R55) (07 - 10): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper (R56LCI) MT (11-13): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper (R56LCI) AT (11-13): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Countryman (R60) (11-16): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Paceman (R61) (11-16): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Clubman (R55) (11-15): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed." Mini Cooper Coupe (R58) (12-15): "Front adjustable sway bar links part number 31 35 6 771 is allowed. Rear adjustable sway bar links part number 35 50 6 772 is allowed."
neutralB-Spec Nissan Versa (09-11) spec line expires 1/1/2025 unless appeal filed by 12/1/2024.
In B-Spec Spec Lines, Nissan Versa (09-11), add to notes the following: "**This Spec line will expire 1/1/2025 unless an appeal is filed on or before 12/1/2024.**"
neutralB-Spec Hyundai Accent rear brakes corrected to 10.3 disc; Kia Rio rear brakes corrected to 10.3 disc.
In B-Spec Spec Lines, Hyundai Accent Hatchback (12-19), change brakes as follows: "(R) 9.9 drum or 10.3 drum disc" In B-Spec Spec Lines, Kia Rio Hatchback (12-19), change brakes as follows: "(R) 10.3 drum disc"
neutralB-Spec and C-Spec restricted to Goodyear Eagle RS/RS-R P205/50R15 and 225/45R17 tires respectively; Hankook tires removed; wet/dry mixing prohibited.
In GCR Section 9.1.10.E.7. change as follows: "a. For the remainder of 2023, B-Spec entrants will be allowed to compete on both Hankook and Goodyear Tires. For B- Spec: tires shall be Hankook 205/50R15 C51, Hankook 200/580R15 Z217, P205/50Z R15 Goodyear Eagle RS (Dry tire) Catalog #D4850 or P205/50ZR15 Goodyear Eagle RS-R (Wet tire) Catalog #D4851. Effective 1-1-2024 Hankook Tires will be allowed at regional events only, through 6-30-2024. Effective 7-1-2024 Goodyear is the only legal specified tire allowed in B-spec for all events. Mixing wet and dry tires is not permitted. Tires may not be modified. All B-Spec competitors are required to place two (2) 12-inch or larger “Goodyear” decals on their cars, one on each side of the car above the front tire. C-Spec: Tires shall be 225/45R17. No Mixing of wet and dry tires on the same car is not permitted. Tires must be run unmodified.
Show 1 more lines
b. When using the Hankook wet tire, all cars get a 0.2” lower ride height allowance due to smaller radius of the wet tire."
fasterB-Spec Sonic restrictors increased to 5-6mm, Fit weight cut 50-25 lbs, Mini Cooper weight reduced 45 lbs, various restrictor adjustments.
In B-Spec Spec Lines, change as follows: Chevrolet Sonic Sedan AT Notes: "33 5mm" Chevrolet Sonic Hatchback AT Notes: "34 6mm" Honda Fit AT (07-08) Weight (lbs): "2400 2350" Notes: "Any aftermarket header allowed."
Show 11 more lines
Honda Fit AT (09-14) Weight: "2525 2500" Notes: "Any Cold Air Intake Package allowed (any manufacturer) with a 25lb adder." Honda Fit CVT (15-19) Notes: "31 3mm" Mini Cooper Hatchback (R50) CVT (02-06) Weight (lbs): "2545 2500" Mini Cooper (R56) AT (07-10) Notes: "44 6mm (OE Catalyst) or 40 2mm (Header)" Mini Cooper (R56LCI) AT (11-13) Notes: "43 5mm (OE Catalyst) or 41mm (Header)"
B-Spec Require hood pins
#36233 from Frank Schwartz · Rule change · TB 24-08 (2024-08 Fastrack)
neutralB-Spec and C-Spec hood pins change from optional to recommended; factory release cable may be removed if pins used.
In GCR, Section 9.1.10.E.41., change as follows: "Optional Hood Pins may be added to supplement the original hood latch system. All parts of the original hood latch system must remain in the car. Installation of hood pins is recommended but not required. If hood pins are used, the factory release and cable must be removed, but the secondary latch may be retained. Vehicles equipped with plastic release cables may replace them with steel units. The OEM hood release latch may be relocated."
B-Spec Sonic Caliper Pistons
#36238 from Jonathan Wickert · Rule change · TB 24-08 (2024-08 Fastrack)
neutralB-Spec and C-Spec Chevrolet Sonic and Cruze allow Babyface Fabrication brake caliper pistons.
In B-Spec Spec Lines, change Chevrolet Sonic Sedan MT (12-19), add to Notes the following: "Allow Babyface Fabrication brake caliper piston SNC-SS." In B-Spec Spec Lines, change Chevrolet Sonic Sedan AT (12-19), add to Notes the following: "Allow Babyface Fabrication brake caliper piston SNC-SS." In B-Spec Spec Lines, change Chevrolet Sonic Hatchback MT (12-19), add to Notes the following: "Allow Babyface Fabrication brake caliper piston SNC-SS." In B-Spec Spec Lines, change Chevrolet Sonic Hatchback AT (12-19), add to Notes the following: "Allow Babyface Fabrication brake caliper piston SNC-SS."
Show 2 more lines
In C-Spec Spec Lines, change Chevrolet Cruze (2010-16), add to Notes the following: "Allow Babyface Fabrication brake caliper piston CRZ-SS."
SRF3 Update Rain Tire Rule and Hoosier Decal Placement
#36436 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)
slowerSRF wet tires: P185/60R13 H20/W2 option removed; P185/65R13 W2 front now required with P205/60R13 W2 rear.
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used. OR Front – Hoosier P/N 46101 P185/65R13 W2 Rear – Hoosier P/N 46105 P205/60R13 W2
Show 8 more lines
1. It is forbidden to regroove tires. 2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for violation will be the loss of qualifying times and/or the disqualification of race results. 3. Hoosier SRF/SRF3 Decal Placement: Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises."
SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info
#36624 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)
neutralSRF Hoosier decal requirement reduced from four decals in specific locations to three decals with simpler placement rules.
In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows: "Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
SRF3 Update SRF3 Air Filter Rule
#36681 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
unclearSRF3 air filter rule removes K&N RC-9160 option, leaving only P/N WM301020 allowed.
In SRF, GCR section 9.1.8.D.2.H.23, change as follows: "Air Filter: P/N WM301020 or K&N RC-9160"
SRF3 Update SRF Brake Rotor Thickness
#36687 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
slowerSRF brake rotor minimum thickness increases from 12.20mm to 13.25mm, Wilwood vented rotor P/N 800065.
In SRF, GCR section 9.1.8.D.1.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."
SRF3 Hoosier Tire Decal Placement
#36739 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
neutralSRF3 Hoosier logo placement changes from four decals to three decals in different locations.
In SRF, GCR section 9.1.8.D.2.B, change as follows: "Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."
FV Disc Brakes
#36822 from Guy Bellingham · Rule change · TB 24-10 (2024-10 Fastrack)
neutralFV ferrous rotor no longer required to be smooth; may have up to three pad cleaning grooves per side.
In FV, GCR section 9.1.1.C.4.D, change as follows: "Any ferrous alloy, unvented rotor may be used, but must have a maximum diameter of 11.75 in. and a minimum thickness of 0.20 in. The otherwise smooth rotor may not be cross-drilled and may have a maximum of three pad cleaning grooves per side."
B-Spec Scion IA/Toyota Yaris/Mazda 2 DY chassis suspension
unclearB-Spec Toyota/Scion IA Sedan 16-20 allows ST Suspension Kit 13275022, requires three Super Tour weekends and OBD-II data submission.
In B-Spec Spec Lines, Toyota/Scion IA Sedan (16-20), change Notes as follows: "38mm FPR. (Effective 11/1/2024) Allow ST Suspension Kit 13275022. This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted."
fasterHonda Fit AT 07-08 B-Spec and C-Spec: rear sway bar Progress #62.1060 and any cold air intake package now allowed.
In B-Spec Spec Lines, Honda Fit AT 07-08, change Notes as follows: "(Effective 11/1/2024) Allow damper and spring set 51600F23SA100, Damper FR LH 51605F23SA100, Damper FR RH 51606F23SA100, Damper RR 52610F23SA100, Spring adjust asy RR 52691F23SA010. Seat upper FR spring 51688F23SA200, 51402FC4YA00 front helper spring and 51403FC4YA00 front spacer permitted. Front Damper Mount P/N 51920-F23S-A30 is allowed. Allow rear sway bar Progress # 62.1060. Any Cold Air Intake Package allowed (any manufacturer). This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted."
B-Spec Remove wheelbase from spec lines and replace with Restrictor
unclearB-Spec and C-Spec cars replace wheelbase spec with induction restrictor (mm) values, effective 2025-01-01.
In B-Spec Spec Lines that are not expiring on 1/1/25, replace Wheelbase as follows: "(Effective 1/1/2025)Wheelbase Restrictor (mm)" In B-Spec Spec Lines, update the value in the spec lines under the Restrictor column as follows effective 1/1/2025: Chevrolet Sonic Sedan MT (12-19): "2525 33" Chevrolet Sonic Sedan AT (12-19): "2525 35" Chevrolet Sonic Hatchback MT (12-19): "2525 34" Chevrolet Sonic Hatchback AT (12-19): "2525 36" Fiat 500 (12-17): "2300"
Show 28 more lines
Ford Fiesta Hatchback (11-19): "2470 39" Ford Fiesta Sedan (11-19): "2470 38" Honda Fit MT (07-08): "2450" Honda Fit AT (07-08): "2450" Honda Fit MT (09-14): "2500" Honda Fit AT (09-14): "2500" Honda Fit MT (15-19): "2530 31" Honda Fit CVT (15-19): "2530 33" Hyundai Accent Hatchback (12-19): "2570 41" Kia Rio Hatchback (12-19): "2570 41" Mazda2 (10-14): "2490" Mini Cooper Hatchback (R50) MT (02-06): "2466" Mini Cooper Hatchback (R50) CVT (02-06): "2466" Mini Cooper (R56) MT (07-10): "2466 44 (OE Catalyst) 40 (Header)" Mini Cooper (R56) AT (07-10): "2466 46 (OE Catalyst 42 (Header)" Mini Cooper Clubman (R55) (07-10): "2547 44 (OE Catalyst) 40 (Header)" Mini Cooper (R56LCI) MT (11-13): "2466 43" Mini Cooper (R56LCI) AT (11-13): "2466 43" Mini Cooper Clubman (R55) (11-15): "2547 42" Mini Cooper Coupe (R58) (12-15): "2466 42" Nissan Micra Cup Cars (Canadian): "2450" Nissan Versa Sedan (2012-2019): "2600" Nissan Versa Hatchback (2012-2019): "2600" Nissan Versa (2020-): "2618 38" Toyota/Scion IA Sedan (16-20): "2570 38" Toyota Yaris Hatchback (07-11): "2461 42" Toyota Yaris Hatchback (12-18): "2510 42" Toyota Yaris Sedan (07-12): "2550 41"
B-Spec Bilstein Rear Shock Request for Hyundai Accent/Kia Rio
#36965 from Alex Ratcliffe · Rule change · TB 25-01 (2025-01 Fastrack)
neutralB-Spec Hyundai Accent and Kia Rio approve Bilstein B8 shock 33-187112 for rear suspension use.
In B-Spec Spec Lines, Hyundai Accent Hatchback (12-19), add to Notes the following: "Bilstein B8 shock 33-187112 approved for use in rear suspension." In B-Spec Spec Lines, Kia Rio Hatchback (12-19), add to Notes the following: "Bilstein B8 shock 33-187112 approved for use in rear suspension."
B-Spec Remove Redundant Language from Notes Sections
neutralB-Spec Honda Fit AT, Fit CVT, Mazda2, Mini Cooper R50 MT and CVT, Toyota Yaris remove redundant notes language.
In B-Spec Spec Lines, Honda Fit AT (07-08), change Notes as follows: "Allow damper and spring set 51600F23SA100, Damper FR LH 51605F23SA100, Damper FR RH 51606F23SA100, Damper RR 52610F23SA100, Spring adjust asy RR 52691F23SA010. Seat upper FR spring 51688F23SA200, 51402FC4YA00 front helper spring and 51403FC4YA00 front spacer permitted. Front Damper Mount P/N 51920-F23S-A30 is allowed. Allow rear sway bar Progress # 62.1060. Any Cold Air Intake Package allowed (any manufacturer). This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted. Any aftermarket header allowed. Allow rear sway bar Progress # 62.1060. Any Cold Air Intake Package allowed (any manufacturer). This configuration is
Show 25 more lines
not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Honda Fit CVT (15-19), change Notes as follows: "Allow damper FR LH 51605F23SA81, Damper FR RH FR RH 51606F23SA81, Damper RR 52610F23SA80, Spring adjust assy RR 52691F23SA80, Camber Adjuster Comp, Damper 51920F23SA82. Exhaust pipe assy 18300F23SA81, ACG belt (6PK858) 31110FC4YA80. Allow rear sway bar Progress 62.1063. Allow Setrab 50- 119-7612 transmission cooler in addition to OEM." In B-Spec Spec Lines, Mazda2 (10-14), change Notes as follows: "Helper springs F&R 0000-04-9926, Spring spacer F&R 0000-04-9925, Rear sway bar 0000-04-2203-RR or 0000-04- 2312, Modified strut bearing plate 0000-04-2204, Crash bolt set 0000-04-2205, Allow rear torque bar Corksport #Mz2-3-070. Cold air intake Corksport Mz2-6-117-31100 and air duct Mz2-6-120-10 are allowed. Exhaust Header (cat delete) HB.EM 60-404- S-SS, HP-MZD001, or Mazda Motorsports PN 0000- 06-2410 permitted. Powerflex PFR19-1511BX2 rear suspension bushings allowed. Allow Mazda part number 0000-01-2501-CR Radiator. Allow Mazda undertray part number DO8C-56-110A, DO8C-56- 311, DO7A-56-321." In B-Spec Spec Lines, Mini Cooper Hatchback (R50) MT (02-06), change Notes as follows: "Allow KW: Coilover Kit: Variant 2: Gen 1 or KW equivalent, Vorshlag Mini R50/53 Camber Plates & Perches allowed. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Allow rear sway bar Progress #62.0210." In B-Spec Spec Lines, Mini Cooper Hatchback (R50) CVT (02-06), change Notes as follows: "Allow KW: Coilover Kit: Variant 2: Gen 1 or KW equivalent, Vorshlag Mini R50/53 Camber Plates & Perches allowed. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Allow rear sway bar Progress #62.0210.CVT equipped cars allow Setrab 50-119-7612 transmission cooler in addition to OEM." In B-Spec Spec Lines, Toyota Yaris Hatchback (07-11), change Notes as follows: "PTR04-52061 TRD Sport shocks permitted. PTR11-52070 TRD spring kit permitted. Speed sensor may be disconnected. Cold air intake K&N 69-8612TFK is allowed. Rear Swaybar PTR11-52071 is allowed. Any Camber plate is permitted."
Applies to Mini Cooper on this page: Trenton Kramer, Thomas Lepper
Applies to Toyota Yaris on this page: Joseph Gersch
neutralB-Spec removes Mini Cooper Countryman R60, Cooper Paceman R61, and two Nissan Versa generations effective 2/1/25.
In B-Spec Spec Lines, delete the following spec lines effective 2/1/25 in their entirety: "Mini Cooper Countryman (R60) (11-16)" "Cooper Paceman (R61) (11-16)" "Nissan Versa (07-11)" "Nissan Versa (09-11)"
B-Spec Set expiration date for Nissan Micra Cup Cars (Canadian)
neutralB-Spec Nissan Micra Cup Car spec line expires 7/1/25 unless appeal submitted by 6/30/25.
In B-Spec Spec Lines, Nissan Micra Cup Car, add to Notes the following: "This spec line will expire on 7/1/25 unless an appeal is submitted by 6/30/25."
Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21
B-Spec Toyota Yaris Hatchback (12-18) rear disc brakes
fasterB-Spec Honda Fit MT intake now limited to three models with 25lb adder; Mazda2 exhaust headers allowed with up to 50lb adder; Mini Coopers FPR increased 1-2 points; Nissan Versa sedans 40lbs lighter, Yaris models 50lbs lighter.
In B-SPEC Spec Lines, change as follows: Honda Fit MT (09-14): "Any Cold Air Intake Package allowed (any manufacturer) Allow Injen Intake SP1512, K&N Intake 69- 1017TTK, or HPS intake 827-102 with a 25lb adder." Mazda2 (10-14): "Exhaust Header (cat delete) HB.EM 60-404-S-SS, HP-MZD001 allowed with a 50lb adder, or Mazda Motorsports PN 0000- 06-2410 permitted with no weight adder." Mini Cooper (R56) MT (07-10): "44 5 FPR (OE Catalyst)" Mini Cooper (R56) AT (07-10): "46 7 FPR (OE Catalyst)" Mini Cooper Clubman (R55) (07-10): "44 5 FPR (OE Catalyst)"
Show 7 more lines
Mini Cooper (R56LCI) MT (11-13): "43 4 FPR" Mini Cooper (R56LCI) AT (11-13): "45 6 FPR (OE Catalyst)" Mini Cooper Clubman (R55) (11-15): "42 4 FPR" Nissan Versa Sedan (12-19): "2490 2450" "Allow Injen intake SP1906" Nissan Versa Hatchback (12-19): "2490 2450" "Allow Injen intake SP1906" Toyota Yaris Hatchback (12-18): "2400 2350" Toyota Yaris Sedan (07-12): "2400 2350"
neutralB-Spec Hyundai Accent and Toyota Yaris weight adjustments: ±25 lbs based on rear brake type.
In B-SPEC Spec Lines, add to Notes the following: Hyundai Accent Hatchback (12-19): "Vehicles equipped with rear drum brakes subtract 25 lb." Toyota Yaris Hatchback (12-18): "Vehicles equipped with rear disc brakes add 25 lb."
B-Spec Request to Update the Spec line for Hyundai Accent and Kia Rio
#37880 from Alex Ratcliffe · Rule change · TB 25-04 (2025-04 Fastrack)
neutralB-Spec Hyundai Accent and Kia Rio (12-19) allow Bilstein B14 kit #47167490 front shocks and BabyFace Fabrication sump extension #BF-HYU-PAN.
In B-SPEC Spec Lines, add to Notes as follows: Hyundai Accent Hatchback (12-19): "Bilstein B14 kit #4716 → 7490 front shocks verified compatible. Allow BabyFace Fabrication sump extension #BF-HYU-PAN." Kia Rio Hatchback (12-19): "Bilstein B14 kit #4716 → 7490 front shocks verified compatible. Allow BabyFace Fabrication sump extension #BF-HYU-PAN."
SRF3 Driver Safety & Comfort
#37966 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)
neutralSRF drivers with disabilities may modify seat and controls for safety and comfort with approval and logbook notation.
In SRF, GCR section 9.1.8.D.1.D, add the following: "f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
SRF3 Update SADEV transmission specs
#37992 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)
slowerB-Spec 07-08 Honda Fit MT minimum weight increases 50 lbs, to 2450.
In B-SPEC Spec Lines, Honda Fit MT (07-08), change as follows: Minimum weight: "2400 2450" Notes: "OEM exhaust manifold required. Primary catalyst may be removed."
B-Spec Add B14 Kit Part # to Honda Fit (07-08) Spec line
neutralB-Spec and C-Spec shift linkage/cables no longer prohibited from any modification; approved aftermarket bushings now permitted.
In GCR, Section 9.1.10.E.46. change as follows: "Aftermarket shift knobs are allowed and shift levers mat y be bent or extended, however the shift linkage/cables must remain stock and may not be modified in any way. Approved aftermarket shift linkage bushings are permitted."
B-Spec Disabling 2 Pedal Shutdown
#38354 from Eric Yagel · Rule change · TB 25-08 (2025-08 Fastrack)
neutralB-Spec Honda Fit MT 09-14 two pedal shutdown may be disabled by cutting/de-pinning pin 42 BKSW at main ECU connector.
In B-Spec Spec Lines, Honda Fit MT (09-14), add to Notes the following: "Two pedal shutdown may be disabled by cutting/de-pinning pin 42 (BKSW) at the main ECU connector in the engine bay."
B-Spec Update Honda Fit MT (07-08) Intake Allowance
slowerB-Spec Honda Fit MT 07-08 intake restricted to Injen SP1511 only, from any Cold Air Intake Package.
In B-Spec Spec Lines, Honda Fit MT (07-08), change Notes as follows: "Bilstein B14 kit 47172401 verified compatible. Allow rear sway bar Progress #62.1060. Any Cold Air Intake Package allowed (any manufacturer). Allow Injen Intake SP1511. This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted. OEM exhaust manifold required. Primary catalyst may be removed."
neutralB-Spec and C-Spec: asterisk removed from public road usage note in rule 9.1.10.D.9.
In GCR, Section 9.1.10.D.9, change as follows: "* If car is used on public roads, these items should be replaced, reactivated, rearmed, etc. when not in competition."
SRF3 SRF Rule Updates
#38853 from Robey Clark · Rule change · TB 25-09 (2025-09 Fastrack)
Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following: "SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual." Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038
Show 11 more lines
may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind; maximum of one spring per caliper. 1. Hawk Blue pads P/N 801993 only 2. Wilwood Vented Rotor P/N 800065 only, as delivered, with no machining of any kind. Minimum thickness 13.25mm (0.522") 3. Wilwood universal caliper Kit P/N 1180008 as delivered, caliper only P/N 800038; Wilwood knock back spring P/N 800045 may be used as delivered, with no machining of any kind, and only one spring per caliper 4. Renault caliper rubber bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185A 5. Renault caliper piston may be replaced with P/N 1196184 vented piston as delivered, with no machining of any kind 6. Girling .750" Master Cylinder P/N 880358 as delivered, with no machining of any kind 7. Wilwood .750" Master Cylinder P/N 880357 as delivered, with no machining of any kind 8. Tilton .750" Master Cylinder P/N 880360 as delivered, with no machining of any kind"
SRF3 Add HD Oil Cooler
#38979 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)
neutralSRF3 adds HD Oil Cooler P/N G1148500 as alternative to standard cooler P/N G480503.
In SRF, GCR section 9.1.8.D.1.V.ff, change as follows: "SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
B-Spec Alternate Shift Cable Bushings and Rear Spring Seats
slowerB-Spec Ford Fiesta Hatchback and Sedan gain 55 lbs to 2525; restrictors increase 1 mm.
In B-Spec Spec Lines, Ford Fiesta Hatchback (11-19), change as follows: Weight (lbs): "(Effective 11/1/2025) 2470 2525" Restrictor (mm) & Type: "(Effective 11/1/2025)39 FPR 40 FPR" In B-Spec Spec Lines, Ford Fiesta Sedan (11-19), change as follows: Weight (lbs): "(Effective 11/1/2025) 2470 2525" Restrictor (mm) & Type: "(Effective 11/1/2025)38 FPR 39 FPR"
B-Spec Request to Remove Rear Shock From Spec Line Hyundai Accents/Kia
#39017 from Alex Ratcliffe · Rule change · TB 25-11 (2025-11 Fastrack)
unclearB-Spec Hyundai Accent and Kia Rio remove Bilstein B8 shock 33-187112 rear suspension approval.
In B-Spec Spec Lines, Hyundai Accent Sedan (12-17), change Notes as follows: "Bilstein B8 shock 33- 187112 approved for use in rear suspension." In B-Spec Spec Lines, Kia Rio Sedan (12-17), change Notes as follows: "Bilstein B8 shock 33- 187112 approved for use in rear suspension."
B-Spec Update Honda Fit MT (07-08) Runoffs Eligibility
fasterB-Spec Honda Fit MT (07-08) becomes Runoffs-eligible; previous three-weekend Super Tour requirement removed.
In B-Spec Spec Lines, Honda Fit MT (07-08), change Notes as follows: "Bilstein B14 kit 47172401 verified compatible. Allow rear sway bar Progress #62.1060. Allow Injen Intake SP1511 OEM exhaust manifold required. Primary catalyst may be removed. This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted. (Effective 11/1/2025) Allow Torque Solution Shifter Cable Bushing kit TS-SCB-506."
neutralB-Spec Chevrolet Sonic and Ford Fiesta, Honda Fit notes reorganized from individual allowances to approved parts lists; wording cleanup.
In B-Spec Spec Lines, Chevrolet Sonic Sedan MT (12-19), change Notes as follows: "GM suspension kit #23123679 permitted. Bilstein B14 kit #47-171725 verifed compatible. Allow rear sway bar ZZ Performance #ZZ-SNCRSB. Allow Aluminum Radiator #ZZP-ZZ013. Allow Babyface Fabrication brake caliper piston SNC-SS. Approved parts: ZZ Performance rear sway bar ZZ-SNCRSB, ZZ Performance radiator ZZP-ZZ013, Babyface Fabrication brake caliper piston SNC-SS. Bilstein B14 kit 47-171725 verified compatible." In B-Spec Spec Lines, Chevrolet Sonic Sedan AT (12-19), change Notes as follows: "GM suspension kit #23123679 permitted. Bilstein B14 kit #47-171725 verifed compatible. Allow rear sway bar ZZ Performance #ZZ-SNCRSB. For automatic allow Setrab 1-series Part No. FP119M221. Allow Aluminum Radiator #ZZP-ZZ013. Allow Babyface
Show 185 more lines
Fabrication brake caliper piston SNC-SS. Approved parts: ZZ Performance rear sway bar ZZ-SNCRSB, ZZ Performance radiator ZZP- ZZ013, Babyface Fabrication brake caliper piston SNC-SS, Setrab transmission cooler 50-119-7612. Bilstein B14 kit 47-171725 verified compatible. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Chevrolet Sonic Hatchback MT (12-19), change Notes as follows: "GM suspension kit #23123679 permitted. Bilstein B14 kit #47-171725 verifed compatible. Allow rear sway bar ZZ Performance #ZZ-SNCRSB. Allow Aluminum Radiator #ZZP-ZZ013. Allow Babyface Fabrication brake caliper piston SNC-SS. Approved parts: ZZ Performance rear sway bar ZZ-SNCRSB, ZZ Performance radiator ZZP-ZZ013, Babyface Fabrication brake caliper piston SNC- SS. World Challenge suspension kit permitted but no longer available. Bilstein B14 kit 47-171725 verified compatible." In B-Spec Spec Lines, Chevrolet Sonic Hatchback AT (12-19), change Notes as follows: "GM suspension kit #23123679 permitted. Bilstein B14 kit #47-171725 verifed compatible. Allow rear sway bar ZZ Performance #ZZ-SNCRSB. For automatic allow Setrab 1-series Part No. FP119M221. Allow Aluminum Radiator #ZZP-ZZ013. Allow Babyface Fabrication brake caliper piston SNC-SS. Approved parts: ZZ Performance rear sway bar ZZ-SNCRSB, ZZ Performance radiator ZZP- ZZ013, Babyface Fabrication brake caliper piston SNC-SS, Setrab transmission cooler 50-119-7612. Bilstein B14 kit #47-171725 verified compatible. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Lines, Ford Fiesta Hatchback (11-19), change Notes as follows: "Suspension kit #M-FR3-FAEB allowed. Rear axle bushing #000-04-2203-RR allowed. Allow rear torque bar Corksport #Mz2-3- 070. Cold air intake K&N 69-3530TS is allowed. Powerflex PFR19-1511BX2 rear suspension bushing allowed. Eibach rear sway bar #35143.312 o r35143.320 is allowed. Mazda front hub D651-33-06 and rear hub D651-26-15XE allowed. Approved parts: Eibach rear sway bar 35143.312, Corksport rear torque bar MZ2-3-070, K&N intake 69-3530TS, Powerflex rear suspension bushing PFR19-1511BX2, Mazda front hub D651-33-06, Mazda rear hub D651-26-15XE." In B-Spec Spec Lines, Ford Fiesta Sedan (11-19), change Notes as follows: "Suspension kit #M-FR3-FAEB allowed. Rear axle bushing #000-04-2203-RR allowed. Allow rear torque bar Corksport #Mz2-3- 070. Cold air intake K&N 69-3530TS is allowed. Powerflex PFR19-1511BX2 rear suspension bushing allowed. Eibach rear sway bar #35143.312 o r35143.320 is allowed. Mazda front hub D651-33-06 and rear hub D651-26-15XE allowed. Approved parts: Eibach rear sway bar 35143.312, Corksport rear torque bar MZ2-3-070, K&N intake 69-3530TS, Powerflex rear suspension bushing PFR19-1511BX2, Mazda front hub D651-33-06, Mazda rear hub D651-26-15XE." In B-Spec Spec Lines, Honda Fit MT (07-08), change Notes as follows: "Bilstein B14 kit 47172401 verified compatible. Allow rear sway bar Progress #62.1060. Allow Injen Intake SP1511 OEM exhaust manifold required. Primary catalyst may be removed. Allow Torque Solution Shifter Cable Bushing kit TS-SCB-506. Approved parts: Progress rear sway bar 62.1060, Injen intake SP1511, Torque Solution shifter cable bushings TS-SCB-506. Bilstein B14 kit 47172401 verified compatible. OEM exhaust manifold required. Primary catalyst may be removed." In B-Spec Spec Lines, Honda Fit AT (07-08), change Notes as follows: "Bilstein B14 kit 47172401 verified compatible. Any aftermarket header allowed. Allow rear sway bar Progress # 62.1060. Any Cold Air Intake Package allowed (any manufacturer). Approved parts: Progress rear sway bar 62.1060, Injen intake SP1511, Setrab transmission cooler 50-119-7612, any aftermarket header. Bilstein B14 kit 47172401 verified compatible." In B-Spec Spec Lines, Honda Fit MT (09-14), change Notes as follows: "Allow damper and spring set 51600F23SA100, Damper FR LH 51605F23SA100, Damper FR RH 51606F23SA100, Damper RR 52610F23SA100, Spring adjust asy RR 52691F23SA010. Seat upper FR spring 51688F23SA200, 51402FC4YA00 front helper spring and 51403FC4YA00 front spacer permitted. Front Damper Mount P/N 51920-F23S-A30 is allowed. Allow rear sway bar Progress # 62.1061 Allow Injen Intake SP1512, K&N Intake 69-1017TTK, or HPS intake 827-102 with a 25lb adder. Allow Acuity Shifter Base Bushing Kit 1954 Two pedal shutdown may be disabled by cutting/de-pinning pin 42 (BKSW) at the main ECU connector in the engine bay. Approved parts: Progress rear sway bar #62.1061, Injen Intake SP1512, K&N Intake 69-1017TTK, or Weapon R Intake 301-166-301, Acuity shifter bushing kit 1954. World Challenge suspension kit permitted but no longer available. Two pedal shutdown may be disabled by cutting/de-pinning pin 42 (BKSW) at the main ECU connector in the engine bay." In B-Spec Spec Lines, Honda Fit AT (09-14), change Notes as follows: "Allow damper and spring set 51600F23SA100, Damper FR LH 51605F23SA100, Damper FR RH 51606F23SA100, Damper RR 52610F23SA100, Spring adjust asy RR 52691F23SA010. Seat upper FR spring 51688F23SA200, 51402FC4YA00 front helper spring and 51403FC4YA00 front spacer permitted. Front Damper Mount P/N 51920-F23S-A30 is allowed. Allow rear sway bar Progress # 62.1061. Allow Setrab 50-119-7612 transmission cooler in addition to OEM. Any aftermarket exhaust/header allowed. Any Cold Air Intake Package allowed (any manufacturer). Weapon R Intake 301-166-301. Approved parts: Progress rear sway bar 62.1061, Injen Intake SP1512, any aftermarket header, Setrab transmission cooler 50-119-7612. Two pedal shutdown may be disabled by cutting/de-pinning pin 42 (BKSW) at the main ECU connector in the engine bay." In B-Spec Spec Lines, Honda Fit MT (15-19), change Notes as follows: "Allow damper FR LH 51605F23SA81, Damper FR RH FR RH 51606F23SA81, Damper RR 52610F23SA80, Spring adjust assy RR 52691F23SA80, Camber Adjuster Comp, Damper 51920F23SA82. Allow rear sway bar Progress 62.1063. Approved parts: Progress rear sway bar 62.1063." In B-Spec Spec Lines, Honda Fit CVT (15-19), change Notes as follows: "Allow damper FR LH 51605F23SA81, Damper FR RH FR RH 51606F23SA81, Damper RR 52610F23SA80, Spring adjust assy RR 52691F23SA80, Camber Adjuster Comp, Damper 51920F23SA82. Allow rear sway bar Progress 62.1063. Allow Setrab 50-119- 7612 transmission cooler in addition to OEM. Approved parts: Progress rear sway bar 62.1063, Setrab transmission cooler 50- 119-7612. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Hyundai Accent Hatchback (12-17), change Notes as follows: "Allow AKSJ03-10-001 Damper Frt Assembly; AKSJ03-20-001 Damper-ASTRear; KSJ03-20-003 Rear Upper Spring Perch Delrin; AKSJ03-60-001 Sump Pan Extension. Allow rear torque bar Evilla Motorsports #KR-B1. Bilstein B8 shock 33- 187112 approved for use in rear suspension. Bilstein B14 kit #47167490 front shocks verified compatible. Allow BabyFace Fabrication sump extension #BF-HYU-PAN Vehicles equipped with rear drum brakes subtract 25 lb. Approved parts: Evilla Motorsports rear torque bar KR-B1, BabyFace Fabrication sump extension BF-HYU-PAN. Vehicles equipped with rear drum brakes subtract 25 lbs." In B-Spec Spec Lines, Hyundai Accent Sedan (12-17), change Notes as follows: "Allow AKSJ03-10-001 Damper Frt Assembly; AKSJ03-20-001 Damper-AST-Rear; KSJ03-20- 003 Rear Upper Spring Perch Delrin; AKSJ03-60-001 Sump Pan Extension. Allow rear torque bar Evilla Motorsports #KR-B1. Bilstein B8 shock 33-187112 approved for use in rear suspension. Approved parts: Evilla Motorsports rear torque bar KR-B1, BabyFace Fabrication sump extension BF-HYU- PAN. Vehicles equipped with rear drum brakes subtract 25 lbs." In B-Spec Spec Lines, Kia Rio Hatchback (12-15), change Notes as follows: "Allow AKSJ03-10-001 Damper Frt Assembly; AKSJ03-20-001 Damper-AST-Rear; KSJ03-20- 003 Rear Upper Spring Perch Delrin; AKSJ03-60-001 Sump Pan Extension. Allow rear torque bar Evilla Motorsports #KR-B1. Bilstein B14 kit #47167490 front shocks verified compatible. Allow BabyFace Fabrication sump extension #BF-HYU-PAN Bilstein B8 shock 33-187112 approved for use in rear suspension. Approved parts: Evilla Motorsports rear torque bar KR-B1, BabyFace Fabrication sump extension BF-HYU-PAN. World Challenge suspension kit permitted but no longer available." In B-Spec Spec Lines, Kia Rio Sedan (12-17), change Notes as follows: "Allow AKSJ03-10-001 Damper Frt Assembly; AKSJ03-20-001 Damper-AST-Rear; KSJ03-20- 003 Rear Upper Spring Perch Delrin; AKSJ03-60-001 Sump Pan Extension. Allow rear torque bar Evilla Motorsports #KR-B1. Bilstein B8 shock 33-187112 approved for use in rear suspension. Approved parts: Evilla Motorsports rear torque bar #KR-B1, BabyFace Fabrication sump extension BF-HYU- PAN." In B-Spec Spec Lines, Mazda2 (10-14), change Notes as follows: "Rear sway bar 0000-04-2203-RR or 0000-04-2312, Allow rear torque bar Corksport #Mz2- 3-070. Cold air intake Corksport Mz2- 6-117-31100 and air duct Mz2-6-120-10 are allowed. Exhaust Header (cat delete) HB.EM 60-404-S-SS, HP-MZD001, allowed with a 50lb adder or Mazda Motorsports PN 0000-06-2410 with no weight adder permitted. Powerflex PFR19- 1511BX2 rear suspension bushings allowed. Allow Mazda part number 0000-01-2501-CR Radiator. Allow Mazda undertray part number DO8C- 56-110A, DO8C-56-311, DO7A-56-321. Approved parts: Mazda Motorsports rear sway bar 0000-04-2203-RR, Eibach/Mazda Motorsports rear sway bar 35143.312/0000-04-2312, Corksport rear torque bar #MZ2- 3-070, Corksport intake MZ2-6-117- 31100, Corksport air duct MZ2-6-120-10, Powerflex PFR19-1511BX2 rear suspension bushings, Mazda Motorsports radiator 0000-01-2501-CR, Mazda Motorsports header 0000-06-2410, Mazda undertray/side shields DO8C-56-110A, DO8C-56-311, DO7A- 56-321." In B-Spec Spec Lines, Mini Cooper Hatchback (R50) MT (02-06), change Notes as follows: "Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Allow rear sway bar Progress #62.0210. Approved parts: Progress rear sway bar 62.0210, Mevotech leteral link CMK100003. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches." In B-Spec Spec Lines, Mini Cooper Hatchback (R50) CVT (02-06), change Notes as follows: "Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Allow rear sway bar Progress #62.0210.CVT equipped cars allow Setrab 50-119-7612 transmission cooler in addition to OEM. Approved parts: Progress rear sway bar 62.0210, Mevotech leteral link CMK100003, Setrab transmission cooler 50-119- 7612. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches." In B-Spec Spec Lines, Mini Cooper (R56) MT (07-10), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. OBX header part #10- 2101-2S permitted. Approved parts: Progress rear sway bar 62.0210, OBX header 10-2101-2S. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. In B-Spec Spec Lines, Mini Cooper (R56) AT (07-10), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125.Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. OBX header part #10-2101-2S permitted. Automatic equipped cars only allow Setrab 50-119-7612 transmission cooler in addition to OEM. Approved parts: Progress rear sway bar 62.0210, Setrab transmission cooler 50-119-7612. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Mini Cooper Clubman (R55) (07-10), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. OBX header part #10- 2101-2S permitted. Approved parts: Progress rear sway bar 62.0210, OBX header 10-2101-2S. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. In B-Spec Spec Lines, Mini Cooper (R56LCI) MT (11-13), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. Approved parts: Progress rear sway bar 62.0210. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches." In B-Spec Spec Lines, Mini Cooper (R56LCI) AT (11-13), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. OBX header part #10- 2101-2S permitted with 41mm FPR. Automatic equipped cars only allow Setrab 50- 119-7612 transmission cooler in addition to OEM. Approved parts: Progress rear sway bar 62.0210, Setrab transmission cooler 50-119-7612. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Mini Cooper Clubman (R55) (11-15), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. Approved parts: Progress rear sway bar 62.0210. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches." In B-Spec Spec Lines, Mini Cooper Coupe (R58) (12-15), change Notes as follows: "Allow L/F Strut-spring assembly 31 31 1 126, R/F Strut-spring assembly 31 31 1 125, Rear Shock-spring assembly 33 50 1 125. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches. Adjustable front camber plate part number 31 30 1 507 is allowed. Allow rear sway bar Progress #62.0210. Approved parts: Progress rear sway bar 62.0210. Ride height measured from the metal underneath the bottom of the plastic door rocker molding shall be no less than 5 inches." In B-Spec Spec Lines, Nissan Versa Sedan (2012-2019), change Notes as follows: "Hardrace HR-Q0146 19mm rear sway bar permitted. Allow Injen intake SP1906. Approved parts: Hardrace rear sway bar HR- Q0146, Injen intake SP1906." In B-Spec Spec Lines, Nissan Versa Hatchback (2012-2019), change Notes as follows: "Hardrace HR-Q0146 19mm rear sway bar permitted. Allow Injen intake SP1906. Approved parts: Hardrace rear sway bar HR- Q0146, Injen intake SP1906." In B-Spec Spec Lines, Nissan Versa (2020-), change Notes as follows: "This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Toyota/Scion IA Sedan (16-20), change Notes as follows: "This configuration is not currently eligible for Runoffs competition. This car must compete in three (3) separate Super Tour weekends so that performance data can be collected. In addition to SCCA data box, OBDII data collected via an AIM or similar device must be submitted. Allow ST Suspension Kit 1327502. Approved parts: ST suspension kit 1327502. This configuration is not currently eligible for Runoffs competition. This car must compete in three separate Majors/Super Tour events so performance data can be collected. In addition to an SCCA data box, OBDII data collected via an AIM or similar device must be submitted." In B-Spec Spec Lines, Toyota Yaris Hatchback (07-11), change Notes as follows: "Speed sensor may be disconnected. Cold air intake K&N 69-8612TFK is allowed. Rear Swaybar PTR11-52071 is allowed. Approved parts: TRD rear sway bar PTR11-52071, K&N intake 69-8612TFK. Speed sensor may be disconnected." In B-Spec Spec Lines, Toyota Yaris Hatchback (12-18), change Notes as follows: "Rear Swaybar PTR11-52071 is allowed. Cold air intake K&N 69-8612TFK is allowed. Speed sensor may be disconnected. Vehicles equipped with rear disc brakes add 25 lb. Approved parts: TRD rear sway bar PTR11-52071, K&N intake 69-8612TFK. Speed sensor may be disconnected. Vehicles equipped with rear disc brakes add 25 lbs." In B-Spec Spec Lines, Toyota Yaris Sedan (07-12), change Notes as follows: "Rear Swaybar PTR11-52071 is allowed. Cold air intake K&N 69-8612TFK is allowed. Speed sensor may be disconnected. Approved parts: TRD rear sway bar PTR11-52071, K&N intake 69-8612TFK. Speed sensor may be disconnected."
Applies to Mini Cooper on this page: Trenton Kramer, Thomas Lepper
Applies to Toyota Yaris on this page: Joseph Gersch
unclearB-Spec: Sonic restrictors removed, Fit MT +25 lbs to 2550, Fit CVT restrictor removed, Mini Coopers restrictors increased 2-4 mm, Versa sedans -25 lbs to 2425, Versa/IA restrictors removed.
In B-Spec Spec Lines, change as follows: Chevrolet Sonic Sedan AT (12-19): Restrictor (mm) & Type: "35 FPR" Chevrolet Sonic Hatchback AT (12-19): Restrictor (mm) & Type: "35 FPR" Honda Fit MT (09-14): Weight (lbs): "2525 2550" Honda Fit CVT (15-19):
Show 23 more lines
Restrictor (mm) & Type: "33 FPR" Mini Cooper Hatchback (R50) MT (02-06): Weight (lbs): "2545 2525" Mini Cooper (R56) MT (07-10): Restrictor (mm) & Type: "FPR 45 47 OE Catalyst" Mini Cooper (R56) AT (07-10): Restrictor (mm) & Type: "47 FPR (OE Catalyst) 42 FPR (Header)" Mini Cooper Clubman (R55) (07-10): Restrictor (mm) & Type: "FPR 45 47 OE Catalyst" Mini Cooper (R56LCI) MT (11-13): Restrictor (mm) & Type: "FPR 44 46" Mini Cooper (R56LCI) AT (11-13): Restrictor (mm) & Type: "46 FPR (OE Catalyst) 41 FPR (Header)" Mini Cooper Clubman (R55) (11-15): Restrictor (mm) & Type: "FPR 44 46" Nissan Versa Sedan (2012-2019): Min weight: "2450 2425" Nissan Versa Hatchback (2012-2019): Min weight: "2450 2425" Nissan Versa (2020-): Restrictor (mm) & Type: "38 FPR" Toyota/Scion IA Sedan (16-20): Restrictor (mm) & Type: "38 FPR"
In B-Spec Spec Lines, Mazda2 (10-14), change Notes as follows: "Exhaust Header (cat delete) HB.EM 60-404-S-SS, HP-MZD001, allowed with a 50lb adder or Mazda Motorsports PN 0000-06- 2410 with no weight adder permitted.”
neutralC-Spec rear sway bars approved for Chevrolet Cruze, Dodge Dart, Ford Focus, Honda Civic, Mazda3i, Toyota Corolla with specified part numbers.
In C-Spec Spec Lines, change Notes as follows: Chevrolet Cruze (2010-16): "Allow BC Racing Q-06-BR suspension kit or RedShift Q-06-CSPEC. Allow Babyface Fabrication brake caliper piston SNC- SS. Approved parts: BC Racing Q-06-BR or RedShift Q-06-CSPEC suspension kit, Babyface Fabrication brake caliper piston SNC- SS, ZZ Performance ZZ-SNCRSB or Whiteline BHR93 rear sway bar. Dodge Dart (2014-16): "Allow BC Racing or RedShift Z-06-CSPEC kit. Approved parts: BC Racing Z-06-BR or RedShift Z-06-CSPEC kit, Progress rear sway bar 62.0606."
Show 28 more lines
Ford Focus Hatchback/Sedan (2011-18): "Allow BC Racing E-21-BR or RedShift E-21-CSPEC kit. Allow Corksport Axl-3-318-Black adjustable rear camber arms. Approved parts: BC Racing E-21-BR or RedShift E-21-CSPEC suspension kit, Corksport Axl-3-318-Black adjustable rear camber arms, Corksport Axl-3-071-12, Eibach 35134.312, or Whiteline BMR78XZ rear sway bar." Honda Civic Coupe/Sedan (2012-15): "Allow BC Racing A-58-BR or RedShift A-18-CSPEC kit. Approved parts: BC Racing A-58-BR or RedShift A-18-CSPEC suspension kit, Progress 62.1026 or Megan Racing MRS-HA-0791 rear sway bar." Honda Civic Coupe/Sedan (2006-11): "Allow BC Racing A-18-BR or RedShift A-58-CSPEC kit. Approved parts: BC Racing A-58-BR or RedShift A-18-CSPEC suspension kit, Progress 62.1026 or Megan Racing MRS-HA-0791 rear sway bar." Mazda3i SKYACTIV (2012-13): "Allow BC Racing N-03-BR or RedShift N-03-CSPEC kit. Allow Corksport Axl-3-318-Black adjustable rear camber arms. Approved parts: BC Racing N-03-BR or RedShift N-03-CSPEC suspension kit, Corksport Axl-3-318-Black adjustable rear camber arms, Corksport Axl-3-071-12, Eibach 35134.312, or Whiteline BMR78XZ rear sway bar." Mazda 3i MZR (2010-13): "Allow BC Racing N-03-BR or RedShift N-03-CSPEC kit. Allow Corksport Axl-3-318-Black adjustable rear camber arms. Approved parts: BC Racing N-03-BR or RedShift N-03-CSPEC suspension kit, Corksport Axl-3-318-Black adjustable rear camber arms, Corksport Axl-3-071-12, Eibach 35134.312, or Whiteline BMR78XZ rear sway bar." Mazda 3i (2004-09): "Allow Corksport Axl-3-318-Black adjustable rear camber arms. Approved parts: BC Racing N-03-BR or RedShift N-03-CSPEC suspension kit, Corksport Axl-3-318-Black adjustable rear camber arms, Corksport Axl-3-071-12, Eibach 35134.312, or Whiteline BMR78XZ rear sway bar." Toyota Corolla (2007-12): "Allow BC Racing C-02-BR or RedShift C-02-CSPEC kit. Approved parts: BC Racing C-02-BR or RedShift C-02-CSPEC suspension kit, TRD PTR11-12080 or Megan Racing MRS-TY-1710 rear sway bar." Toyota Corolla (2013-18): "Allow BC Racing C-02-BR or RedShift C-02-CSPEC kit. Approved parts: BC Racing C-02-BR or RedShift C-02-CSPEC suspension kit, TRD PTR11-12080 or Megan Racing MRS-TY-1710 rear sway bar."
What the rules allowed changed as listed; this does not say what any particular car ran.