SRF3 + GTX + T1 + B Spec at Buttonwillow Raceway Park
No mapCal Club 2024
This track has been raced on 2 configurations (The Circuit, 2.57 mi; 2.92 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
B Spec has no laps in the events chosen. It ran at Cal Club 2024: add that event.
One run is left out as not that car's own laps (far quicker than the car managed in any other session and than anyone else in its class all week; usually a swapped transponder): Tom Burt in Cal Club 2025 PM (1:42.300; the car's best in any other session was 1:52.334 and the rest of the class's best all week 1:50.233).
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
BMW M3
T1
1
1:46.465Ian Barberi
1:46.465Ian Barberi
1:47.434Ian Barberi
114.9Ian Barberi
28.992Ian Barberi
30.811Ian Barberi
46.263Ian Barberi
BMW M4 GT4
T1
1
1:47.084Drew Delmonico
1:47.084Drew Delmonico
1:47.467Drew Delmonico
161.4Drew Delmonico
29.150Drew Delmonico
30.850Drew Delmonico
46.316Drew Delmonico
Chevrolet
GTX
2
1:49.569Bob Blizzard
124.8Michael Arnheiter
29.869Bob Blizzard
31.704Bob Blizzard
47.478Bob Blizzard
Chevrolet
GTX
1
1:49.569Bob Blizzard
124.2Bob Blizzard
29.869Bob Blizzard
31.704Bob Blizzard
47.478Bob Blizzard
Chevrolet Camero
GTX
1
1:59.339Michael Arnheiter
124.8Michael Arnheiter
32.354Michael Arnheiter
33.705Michael Arnheiter
50.741Michael Arnheiter
Ford Mustang GT4
GTX/T1
2
1:49.596Rob Scholl
1:49.596Rob Scholl
116.4Rob Scholl
30.070Rob Scholl
31.820Rob Scholl
46.910Rob Scholl
Ford Mustang GT4
GTX
1
1:49.596Rob Scholl
1:49.596Rob Scholl
116.4Rob Scholl
30.070Rob Scholl
31.820Rob Scholl
46.910Rob Scholl
Ford Mustang
T1
1
1:59.261Pratt Cole
1:59.261Pratt Cole
98.6Pratt Cole
32.624Pratt Cole
34.661Pratt Cole
51.577Pratt Cole
SCCA Ent SRF3
SRF3
38
1:50.233Caleb Shrader
1:50.233Caleb Shrader
1:50.825Caleb Shrader
138.9Paul Marino
30.136Caleb Shrader
31.672Caleb Shrader
44.841Tom Burt
Porsche 981 Cayman
GTX
1
1:54.892Moze Cowper
1:54.892Moze Cowper
1:55.330Moze Cowper
146.0Moze Cowper
31.377Moze Cowper
32.983Moze Cowper
49.706Moze Cowper
Pontiac GTO
T1
1
1:59.123Ed Gless
1:59.760Ed Gless
1:59.123Ed Gless
120.7Ed Gless
32.383Ed Gless
34.587Ed Gless
51.370Ed Gless
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
T1 9.1.9.1 T1 new category item/ line 26 rule to expire Jan 1 2023
neutralMercedes AMG-C63 S (2023) classified in T1 with 4000 lbs minimum weight and 3700 restrictor.
In T1 Spec Lines, classify Mercedes AMG-C63 S (2023) as follows:
A specification table follows in the original; it is not shown here.
SRF3 SRF3 Alternator Pulley Update In
#36095 from Robey Clark · Rule change · TB 24-06 (2024-06 Fastrack)
fasterSRF3 alternator pulley minimum weight reduced from 12 oz to 11 oz.
SFR3, GCR section 9.1.8.D.2.H.17, change as follows: "Alternator Pulley: P/N G902130, or P/N G902130A, or P/N G902131 (six row). 12 11 oz minimum weight."
SRF3 Update Rain Tire Rule and Hoosier Decal Placement
#36436 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)
slowerSRF wet tires: P185/60R13 H20/W2 option removed; P185/65R13 W2 front now required with P205/60R13 W2 rear.
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used. OR Front – Hoosier P/N 46101 P185/65R13 W2 Rear – Hoosier P/N 46105 P205/60R13 W2
Show 8 more lines
1. It is forbidden to regroove tires. 2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for violation will be the loss of qualifying times and/or the disqualification of race results. 3. Hoosier SRF/SRF3 Decal Placement: Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises."
SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info
#36624 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)
neutralSRF Hoosier decal requirement reduced from four decals in specific locations to three decals with simpler placement rules.
In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows: "Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
SRF3 Update SRF3 Air Filter Rule
#36681 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
unclearSRF3 air filter rule removes K&N RC-9160 option, leaving only P/N WM301020 allowed.
In SRF, GCR section 9.1.8.D.2.H.23, change as follows: "Air Filter: P/N WM301020 or K&N RC-9160"
SRF3 Update SRF Brake Rotor Thickness
#36687 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
slowerSRF brake rotor minimum thickness increases from 12.20mm to 13.25mm, Wilwood vented rotor P/N 800065.
In SRF, GCR section 9.1.8.D.1.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."
SRF3 Hoosier Tire Decal Placement
#36739 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
neutralSRF3 Hoosier logo placement changes from four decals to three decals in different locations.
In SRF, GCR section 9.1.8.D.2.B, change as follows: "Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."
T1 Changes to T1 Tires for GT4 and Other Cars
#35383 from Andrew Aquilante · Rule change · TB 24-12 (2024-12 Fastrack)
unclearT1 GT4 tire sizes adjusted across ten cars: most non-DOT rear to 305/660, Audi and McLaren 305/645, Camaro and Mustang 305/680.
In T1 GT4 Spec Lines, change Tire Size as follows: Aston Martin Vantage AMR GT4 4010: "315 DOT, 305/660 Non-DOT" Audi R8 GT4 - Spec Line #4020: "315 DOT, 305/645 Non-DOT" BMW M4 GT4 - Spec Line #4030: "315 DOT, 305/660 Non-DOT" Chevrolet Camaro GT4-R- Spec Line #4035: "315 DOT, 305/680 Non-DOT" Ford Mustang GT4 - Spec Line #4040: "315 DOT, 315/680 Non-DOT" Mclaren 570S GT4 - Spec Line #4050: "315 DOT, 305/645 Non-DOT" Mercedes AMG GT4 - Spec Line #4060: "315 DOT, 305/660 Non-DOT"
Show 3 more lines
Porsche 718 Cayman GT4 CS MR - Spec Line #4070: "315 DOT, 305/660 Non-DOT" Porsche 718 GT4 RS Clubsport - Spec Line #4080: "315 DOT, 305/660 Non-DOT" Toyota Supra GR GT4 - Spec Line #4090: "315 DOT, 305/660 Non-DOT"
neutralBMW M4 GT4 (G82) added to T1 GT4 at 3525 lbs minimum weight with Red power stick control.
In T1 GT4 Spec Lines, SL#4030, change as follows: Model: "BMW M4 GT4 (F82)" Performance Control: "Gold power stick Red power stick" In T1 GT4 Spec Lines, classify BMW M4 GT4 (G82) as follows:
A specification table follows in the original; it is not shown here.
T1 Alt. Clutch Allowance
#36606 from Hugh Stewart · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT1 Spec Lines now permits 5.5 inch clutch in Engine Notes.
In T1 Spec Lines, SL# 1050, change add to Engine Notes the following: "5.5 inch clutch permitted."
T1 BOP Changes Need Updates
#36667 from Joe Rainey · Rule change · TB 24-12 (2024-12 Fastrack)
fasterT1 GT4 Spec Line 4020 restrictor opens from 44mm to 45mm, minimum weight drops to 3400 lbs.
In T1 GT4 Spec Lines, Spec Line 4020, change as follows: Performance Control: Power level 2020, 44mm 45mm SRO compliant restrictor" Min. Weight with driver (LBS): "3550 3400"
T1 Request Ford Performance Darkhorse R in T1
#37136 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)
neutralMustang Darkhorse R added to T1 homologated cars at 3,250 lbs minimum with 305/315 tires, ineligible for Runoffs until 3 Super Tour events.
In T1-Homologated Cars Spec Line, classify Mustang Darkhorse R (Mustang Challenge) as follows: T1 – Homologated Cars
A specification table follows in the original; it is not shown here.
T1 Car Mods for T1 Corvette under line item 1150
#37173 from Thomas Napolitano · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT1 Corvette may roll or flatten wheel opening lips for tire clearance; plastic fenders may remove lips if edge thickness matches basic material.
In GCR, Section 9.1.9.1.A.2,, add the following: "It is permitted to roll under or flatten any interior lip on the wheel opening for tire clearance. Cars with plastic/composite fenders may remove any interior wheel opening lip, but the resulting material edge shall be no thinner than the basic fender material thickness. Non-metallic inner fender liners may be removed. Vents may be added to fenders."
T1 Increased Bore Throttle Bodies for E46 M3 S54 Engine
#37273 from Mark Pfeffer · Rule change · TB 24-12 (2024-12 Fastrack)
fasterT1 E46 M3 S54 can now use Dinan Throttle Body #D760-3400 on 3.250L engine.
In T1 Spec Lines, E46 M3 Spec Line # 1050, add to Engine Notes the following: "Dinan Throttle Body #D760-3400 allowed on the 3.250L."
GTX Correct language regarding OEM Areo Devices
#37137 from Christopher Childs · Rule change · TB 25-01 (2025-01 Fastrack)
In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows: "B. Aerodynamic Devices 2. Rear wing c. The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule."
A specification table follows in the original; it is not shown here.
T1 T1 Parity Compared to GT4
#37170 from Tony Ave · Rule change · TB 25-02 (2025-02 Fastrack)
slowerT1 Mustang gains 125 lbs to 3600, restrictor shrinks 65mm to 60mm. Corvette gains 50 lbs to 3500, restrictor shrinks 70mm to 67mm. BMW deleted.
In T1 Spec Lines, change Weight and Restrictor Required as follows: Mustang - Spec Line 1430 Weight: "3475 3600" Restrictor Required: "65mm 60mm - FPR" Corvette Spec Line 1190 Weight: "3450 3500" Restrictor Required: "70mm 67mm - Flat Plate" In T1 Spec Lines, delete Spec Line BMW # 1190 in its entirety.
T1 Clarification of Request Approval #37273
#37399 from Mark Pfeffer · Rule change · TB 25-02 (2025-02 Fastrack)
unclearT1 E46 M3 Spec Line 1050 allows VAC Motorsports throttle body VAC-TB-S54 on 3.250L engine instead of Dinan.
In T1 Spec Lines, E46 M3 Spec Line # 1050, change Engine Notes as follows: "Dinan Throttle Body #D760-3400 VAC Motorsports #VAC-TB-S54 allowed on the 3.250L."
unclearT1 Mustang Spec 1430 restrictor opens 60mm to 65mm; Spec 1460 weight rises to 3500 lbs, restrictor 70mm; Corvette 1190 restrictor opens 67mm to 70mm; BMW 1090 restrictor narrows 40mm to 35mm; BMW 1100 weight rises to 3350 lbs.
In T1 Spec Lines, change Weight, Restrictor Required and/or Notes as follows: Mustang - Spec Line 1430: Restrictor Required: "60mm 65mm - FPR" Mustang - Spec Line 1460: Weight: "3425 3500" Restrictor Required: "70mm - FPR" Corvette Spec Line 1190: Restrictor Required: "67mm 70mm - Flat Plate"
Show 5 more lines
BMW - Spec Line 1090: Required Restrictor: "(2) X 40mm 35mm diameter hole inlet restrictor plate required" Chassis Notes: "This spec line is set to expire 12/31/25." BMW - Spec Line 1100: Minimum Weight: "3150 3350”
SRF3 Driver Safety & Comfort
#37966 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)
neutralSRF drivers with disabilities may modify seat and controls for safety and comfort with approval and logbook notation.
In SRF, GCR section 9.1.8.D.1.D, add the following: "f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
SRF3 Update SADEV transmission specs
#37992 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)
neutralCadillac CT4-V Blackwing added to T1 Spec Line 1115, 3564cc, 3750 lbs minimum weight.
In T1 Spec Lines, classify Cadillac CT4-V Blackwing as follows:
A specification table follows in the original; it is not shown here.
T1 Acceptance of Porsche 981 GT4 Clubsport into T1
#36664 from John Brown · Rule change · TB 25-05 (2025-05 Fastrack)
neutralPorsche 981 GT4 Clubsport added to T1 as spec line 4085, minimum weight 3100 lbs with driver.
In T1-GT4 Spec Lines, classify Porsche 981 GT4 Clubsport as follows:
A specification table follows in the original; it is not shown here.
T1 Request to Restore T1 Honda S2000 to Proper Weights
#37644 from David Mead · Rule change · TB 25-05 (2025-05 Fastrack)
fasterT1 Honda S2000 minimum weight reduced from 2950 lbs to 2900 lbs.
In T1 Spec Lines, Honda S2000, Spec Line 1530, change as follows: Minimum Weight: "2950 2900" Chassis Notes: "This spec line is set to expire as of 12/31/2025 if not represented in Majors competition in 2025."
T1 DCT Transmission in E46
#37964 from Matt Spicuzzi · Rule change · TB 25-05 (2025-05 Fastrack)
neutralT1 BMW E46 M3 permits BMW #GS7D36SG aftermarket sequential transmission in SL# 1060 and 1070.
In T1 Spec Lines, BMW E46 M3, add to Chassis Notes the following: SL# 1060: "BMW #GS7D36SG transmission permitted as an aftermarket sequential option." SL# 1070: "BMW #GS7D36SG transmission permitted as an aftermarket sequential option."
Applies to BMW M3 on this page: Ian Barberi
GTX Request to Classify Porsche GT2 RS Clubsport
#37972 from Paul Fairchild · Rule change · TB 25-05 (2025-05 Fastrack)
neutralGTX Porsche GT2 RS Clubsport classified with factory specifications required at all race events.
In GTX, Classify Porsche GT2 RS Clubsport, as follows: GTX Make Homologation Model Restrictor (mm) Weight (lbs) Notes Porsche GT2 RS Clubsport Must have factory specifications available at all race events
T1 Reduce E92 M3 Minimum Weight to 3050
#38092 from Shane Brown · Rule change · TB 25-05 (2025-05 Fastrack)
fasterT1 BMW M3 E92 minimum weight reduced to 3300 lbs.
In T1 Spec Lines, BMW M3 E92 (08-13), Spec Line 1100, change Min. Weight as follows: "3350 3300"
fasterT1 Mustang Darkhorse R gets 315 front and rear tyres, loses 500 lbs minimum weight to 3600.
In T1 Spec Lines, Mustang Darkhorse R (Mustang Challenge) Spec Line- 4119, change as follows: Tire size: "305 315 (f) 315(r)" Performance Control: "TBD" Min. Weight with driver (LBS): "10.5 (f) 11 (r) 3600" Chassis Notes: "Must conform to Mustang Challenge Rules. Tires conforming to Mustang Challenge rules are permitted. **This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
GTX Ligier P3 LS Swap
#38164 from Bart Wolf · Rule change · TB 25-06 (2025-06 Fastrack)
unclearGTX Ligier LMP3 now allows any normally aspirated LS Chevrolet engine.
In GTX Spec Lines, GTX-MISC., Ligier, LMP3, 3.0L, Add to Notes the following: "Allow any normally aspirated LS Chevrolet engine may be used."
SRF3 SRF Rule Updates
#38853 from Robey Clark · Rule change · TB 25-09 (2025-09 Fastrack)
Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following: "SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual." Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038
Show 11 more lines
may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind; maximum of one spring per caliper. 1. Hawk Blue pads P/N 801993 only 2. Wilwood Vented Rotor P/N 800065 only, as delivered, with no machining of any kind. Minimum thickness 13.25mm (0.522") 3. Wilwood universal caliper Kit P/N 1180008 as delivered, caliper only P/N 800038; Wilwood knock back spring P/N 800045 may be used as delivered, with no machining of any kind, and only one spring per caliper 4. Renault caliper rubber bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185A 5. Renault caliper piston may be replaced with P/N 1196184 vented piston as delivered, with no machining of any kind 6. Girling .750" Master Cylinder P/N 880358 as delivered, with no machining of any kind 7. Wilwood .750" Master Cylinder P/N 880357 as delivered, with no machining of any kind 8. Tilton .750" Master Cylinder P/N 880360 as delivered, with no machining of any kind"
SRF3 Add HD Oil Cooler
#38979 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)
neutralSRF3 adds HD Oil Cooler P/N G1148500 as alternative to standard cooler P/N G480503.
In SRF, GCR section 9.1.8.D.1.V.ff, change as follows: "SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
T1 Keep S2000 Classification
#39344 from David Mead · Rule change · TB 25-12 (2025-12 Fastrack)
unclearUnable to summarize: letter states intent but provides no actual rule changes to S2000 specification.
In T1 Spec Lines, reinstate Spec Line # 1139, Chevrolet Corvette C6 (05-13) Includes Z51, GrandSport, Z06, Z06 Carbon, as follows: Max Displ: "LS1, LS6 OEM" Min Weight: "3200" Required Restrictor: "70mm"
What the rules allowed changed as listed; this does not say what any particular car ran.