This track has been raced on 4 configurations (The Circuit, 2.57 mi; 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
5 laps are left out as timing errors (far too short to be a lap of this track). The rest of those sessions, sectors included, is used.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Pro Formula Mazda
FA
1
1:14.588Greg Labadie
1:14.588Greg Labadie
Swift 016
FA
1
1:35.792Greg Labadie
1:35.792Greg Labadie
1:37.275Greg Labadie
163.8Greg Labadie
26.713Greg Labadie
26.816Greg Labadie
41.822Greg Labadie
Lamborghini Huracan GT3 Evo
GT1
1
1:39.857Michael McAleenan
1:39.857Michael McAleenan
1:41.045Michael McAleenan
167.6Michael McAleenan
27.368Michael McAleenan
29.135Michael McAleenan
42.926Michael McAleenan
Jaguar XKR
GT1
1
1:39.901Michael Lewis
1:39.901Michael Lewis
1:41.635Michael Lewis
151.5Michael Lewis
27.895Michael Lewis
28.765Michael Lewis
43.241Michael Lewis
BMW M3
T1
1
1:46.465Ian Barberi
1:46.465Ian Barberi
1:47.434Ian Barberi
114.9Ian Barberi
28.992Ian Barberi
30.811Ian Barberi
46.263Ian Barberi
BMW M4 GT4
T1
1
1:47.084Drew Delmonico
1:47.084Drew Delmonico
1:47.467Drew Delmonico
161.4Drew Delmonico
29.150Drew Delmonico
30.850Drew Delmonico
46.316Drew Delmonico
Mazda RX-7
GT1
1
1:53.007Michael Lewis
1:53.007Michael Lewis
110.9Michael Lewis
30.700Michael Lewis
32.429Michael Lewis
49.385Michael Lewis
Ford Mustang
AS/T1
5
1:55.849Roger Eagleton
1:56.445Roger Eagleton
1:55.849Roger Eagleton
135.2Ross Murray
31.659Roger Eagleton
33.571Roger Eagleton
50.288Ross Murray
Ford Mustang
AS/T1
5
1:55.849Roger Eagleton
1:56.445Roger Eagleton
1:55.849Roger Eagleton
135.2Ross Murray
31.659Roger Eagleton
33.571Roger Eagleton
50.288Ross Murray
Ford Mustang FR500S
AS
1
1:58.795Pratt Cole
1:59.911Pratt Cole
1:58.795Pratt Cole
103.3Pratt Cole
32.531Pratt Cole
33.997Pratt Cole
51.550Pratt Cole
Pontiac GTO
T1
1
1:59.123Ed Gless
1:59.760Ed Gless
1:59.123Ed Gless
120.7Ed Gless
32.383Ed Gless
34.587Ed Gless
51.370Ed Gless
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
T1 Sequential Gearbox Limitations in T1
#33691 from David Mead · Rule change · TB 23-03 (2023-03 Fastrack)
neutralT1 cars with aftermarket sequential transmissions get 10-inch max bellhousing; non-sequential cars gain 100 lbs weight break.
In GCR, Section 9.1.9.1.I.4., change as follows: "Aftermarket sequential transmissions are permitted. Cars with aftermarket sequential shift transmissions shall utilize a 1:1 (or greater/overdriven) ratio in top gear. Transmission location must be OEM. Maximum bellhousing length is 10 inches. Cars that don’t use an aftermarket sequential transmission may decrease their competition weight by 100 lbs."
In T1 Spec Lines, Chevrolet Camaro Gen 5 ('10-'15) Including SS, Z28, classify Spec Line Number 1135 as follows:
A specification table follows in the original; it is not shown here.
GT1 Mercedes AMG GT3 Notes
#33804 from Gary D'Abate · Rule change · TB 23-04 (2023-04 Fastrack)
neutralGT1 Mercedes AMG GT3 16-19 preparation wording changed to per FIA GT3 homologation.
In GT1-ST Spec Lines, Mercedes Benz AMG GT3 (16-19), change Notes as follows: "Car must be prepared to per its FIA GT3 homologation. except as specified differently within the GT1 class rules."
GT1 Please classify Fields Cardinal V8
#33784 from James Rogersn · Rule change · TB 23-05 (2023-05 Fastrack)
neutralFields Cardinal V8 classified in GT1 with Ford V8 engine, 4.9L displacement, 2100 lbs minimum weight.
In GT Spec Lines, GT1 Cars - Fields Cardinal, classify Fields Cardinal V8 as follows: GT1 Cars – Fields Cardinal Model Years Body Style Drive- line Wheel- base (in) Notes Fields Cardinal V8 2023 2 Dr. RWD 92.0 Roll Cage MUST be modified to comply with
Show 6 more lines
GCR Section 9.4. In GT Spec Lines, GT1Engines - classify Ford V8 as follows: GT1 Engines - Ford Engine Family Engine Type Bore x
A specification table follows in the original; it is not shown here.
neutralT1 GT4 weights clarified for nine cars, ranging from 3200 lbs Porsche 718 Cayman to 3575 lbs Aston Martin.
RM 23-04 – Touring 1 weights dated 3/21/2023 As an E&O to the February Fastrack, in T1-GT4 leave weights as follows: Aston Martin Vantage AMR GT4: 3575 Audi R8 GT4: 3550 BMW M4 GT4: 3500 Ford Mustang GT4: 3550 Maclaren 570S GT4: 3450 Mercedes AMG GT4: 3450
Show 3 more lines
Porsche 718 Cayman GT4 CS MR: 3200 Porsche 718 GT4 RS Clubsport: 3450 Toyota Supra GR GT4: 3350
FA E&O - Correct Pro Formula Mazda spec line dimensional equivalent
#34085 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)
fasterFA Pro Formula Mazda maximum bodywork width behind front wheels increases to 51.97 inches.
In FA Table 2, Pro Formula Mazda spec line, change as follows: "The overall maximum width of the bodywork behind the front wheels shall not exceed 132cm (51.17 51.97 inches)."
FA Add new spec line for MSR Formula Mazda FMzR to Table 2
#34139 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)
neutralFA MSR Formula Mazda FMzR added to Table 2 classification.
RM 23-06 – MSR - FMzR Formula Atlantic Classification dated 4/21/2023 In FA Table 2, add a spec line as follows:
T1 Touring 1 Tire Sizes
#34191 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)
fasterT1-GT4 McLaren 570S and Mercedes AMG GT4 front tires widen to 315 mm.
#34048 from David Mead · Rule change · TB 23-06 (2023-05 Fastrack)
neutralT1 Ford Mustang S197 (05-14) reinstated with 3550 lbs minimum weight, 75mm restrictor, Voodoo engine permitted.
In T1 Spec Lines, classify Ford Mustang S197 (05-14) Includes GT, Boss302, 302S, 302R, FR500C, FR500S as follows:
A specification table follows in the original; it is not shown here.
Applies to Ford Mustang on this page: Pratt Cole
FA Simplify Pro Formula Mazda wheel allowance
#34190 from Club Racing Board · Rule change · TB 23-06 (2023-06 Fastrack)
unclearFA Pro Formula Mazda front wheels widen to 10 in. max; rear wheels narrow to 14 in. min.
In FA, Pro Formula Mazda spec line, change wheel width as follows: "Pro Mazda series wheels
A specification table follows in the original; it is not shown here.
T1 Gen 5 Camaro Engine
#33875 from Matt Spicuzzi · Rule change · TB 23-06 (2023-07 Fastrack)
neutralT1 Chevrolet Camaro Gen 5 LS7 gets two spec lines: 1131 with 70mm restrictor, 1136 with 53mm restrictor, both 3450 lbs minimum.
In T1-NEW Spec Lines, Chevrolet Camaro Gen 5 (10-15) Including SS, Z28, classify Spec Line Number 1131 and 1136 as follows:
A specification table follows in the original; it is not shown here.
T1 Inquiry to letter #33682
#34071 from Andrew Aquilante · Rule change · TB 23-06 (2023-07 Fastrack)
slowerT1 Chevrolet Camaro Gen 5, Corvette C5 and C6: engine resleeve restricted to stock parameters only, no longer LS3 bore/stroke.
In T1 NEW Spec Lines, Chevrolet Camaro Gen 5 (10-15) Including SS, Z28, change Engine Notes as follows: 1130: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1135: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement.May resleeve to stock parameters for engine repair or replacement." In T1 NEW Spec Lines, Chevrolet Corvette C5 (‘97-’04) – Includes: Z06, Coupe, Convertible, change Engine Notes as follows: 1132: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement."
Show 18 more lines
1134: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1136: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1138: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." In T1 NEW Spec Lines, Chevrolet Corvette C6 (05-13) - Includes Z51, GrandSport, Z06, Z06 Carbon, change Engine Notes as follows: 1150: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1160: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1170: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1180: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1190: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement."
T1 Viper Cleanup
#34107 from Scotty B White · Rule change · TB 23-06 (2023-05 Fastrack)
fasterT1 Dodge Viper ACR/ACR-X restrictor increases from 50mm to 60mm flat plate.
In T1 NEW Spec Lines, Dodge Viper ACR/ACR-X Spec Line 1360, change Required Restrictor as follows: "50mm 60mm flat plate"
T1 Viper 8300 OEM FPR Size
#34268 from Scotty B White · Rule change · TB 23-06 (2023-05 Fastrack)
unclearT1 Dodge Viper ACR/ACR-X: Spec Line 1370 restrictor increases to 55mm, Line 1390 decreases to 55mm.
In T1 NEW Spec Lines, Dodge Viper ACR/ACR-X Spec Line 1370, change Required Restrictor as follows: "(2) 47mm 55mm flat plates" In T1 NEW Spec Lines, Dodge Viper ACR/ACR-X Spec Line 1390, change Required Restrictor as follows: "(2) 60mm 55mm flat plates"
T1 Ford Mustang S197 (05-14) Clarification
#34450 from Club Racing Board · Rule change · TB 23-06 (2023-05 Fastrack)
neutralT1 Ford Mustang S197 05-14 now requires OEM 8.8 differential housing.
In T1-NEW Spec lines, Ford Mustang S197 (05-14) Includes GT, Boss302, 302S, 302R, FR500C, FR500S, change Notes as follows: "OEM 8.8 Differential Housing"
AS Crate Motor Part Numbers
#32944 from Sam Daniels · Rule change · TB 23-08 (2023-08 Fastrack)
neutralAS crate motor part number specified: GM Performance CT400 P/N 19370604 engine assembly for GM vehicles.
In AS, GCR Section 9.1.6.F.2., change as follows: "GM Performance parts CT400 P/N-1937 → 0604 or 1937 → 0604 engine assembly for GM produced vehicles."
AS Request wheel size change
#33007 from Michael Kamalian · Rule change · TB 23-08 (2023-08 Fastrack)
fasterAS Spec Lines Ford Mustang GT 5.0L (15-17) max wheel size increases to 19.0 inches.
In AS Spec Lines, Ford Mustang GT 5.0l (15-17) Restricted Preparation, change Notes as follows: "Max. Wheel Size: Dia.18.0 19.0 inches."
Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole
AS Alternative Upper Front Control Arms for Dodge Challenger
#33352 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)
neutralAS Dodge Challenger 5.7L/6.1L/6.4L V8 now permits SPC-66045 alternate front upper control arms.
In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2 valves/cylinder, change Notes as follows: "SPC-66045 Alternate front upper control arms are permitted."
AS Front Brake Caliper Adapters for Dodge Challenger
#33353 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)
neutralAS Dodge Challenger 5.7L/6.1L/6.4L V8 allows alternate front brake caliper adapters for updated or backdated components.
In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2 valves/cylinder, change Notes as follows: "Stock brakes or alternate Dodge brakes (Part numbers: front caliper (0517 → 5106 (R) and 0517 → 5107 (L); rear caliper (R1542564 (R) and R1542565 (L))) may be used with the brake rotor sizes listed in this specification line. Alternate brackets may be used to facilitate updated/backdated components."
T1 C5 Approved Aero That Was Mistakenly Deleted
#34374 from Joe Aquilante · Rule change · TB 23-08 (2023-08 Fastrack)
fasterT1 Corvette C5 gains approved aero parts: carbon rear spoiler, vented front splitter, side skirts, with 50 lb weight reduction allowed.
In T1 NEW Spec Lines, Chevrolet Corvette C5 (‘97-’04) – Includes: Z06, Coupe, Convertible, Spec Lines 1132-1138, add to Notes as follows: "Any option of OEM Bodywork parts may be used as basis for aero measurements. Rear spoiler max 5” Above bumper allowed. +50lbs. The following parts are permitted, with a 50lb decrease from base weight, in lieu of the aero options permitted in 9.1.9.1.B: (C7Carbon Rear- Spoiler CCC5 EX- RSB-GB, Vented Front Splitter CCC5-FS-GB, Side Skirts CCC5 SS-GB.)"
T1 Why no Camaro?
#34421 from Scotty B White · Rule change · TB 23-08 (2023-05 Fastrack)
neutralChevrolet Camaro GT4-R classified in T1 GT4 Spec Line 4035, minimum weight 3375 lbs, 315 max tire, 63mm restrictor, ineligible for Runoffs.
In T1 GT4 Spec Lines, classify Chevrolet Camaro GT4-R as follows:
A specification table follows in the original; it is not shown here.
T1 Request to Remove Expiration from T1 spec lines #1350 & #1370
#34470 from Scotty B White · Rule change · TB 23-08 (2023-05 Fastrack)
neutralT1 Dodge Viper ACR / SRT RT-10 and ACR/ACR-X spec lines 1350 and 1370 remove 12/23 expiration.
In T1 NEW Spec Lines, Dodge Viper ACR / SRT RT-10, change Spec Line Number as follows: "1350 *Spec line Expires 12/23*" In T1 NEW Spec Lines, Dodge Viper ACR/ACR-X, change Spec Line Number as follows: "1370 *Spec line Expires 12/23*"
neutralT1 GT4 BMW M4 Spec Line Number changed from 4050 to 4030.
In T1 GT4 Spec Lines, BMW M4, change Spec Line Number as follows: "4050 4030"
T1 New T1 add spec line for C5 corvette LS2 engines (Copy from C6)
#33764 from Craig Anderson · Rule change · TB 23-12 (2023-09 Fastrack)
neutralT1 Chevrolet Corvette C5 LS2 added with 6000cc displacement, 3300 lbs minimum weight, 72mm flat plate restrictor.
In T1 Spec Lines, classify Chevrolet Corvette C5 (‘97-’04) – Includes: Z06, Coupe, Convertible as follows:
A specification table follows in the original; it is not shown here.
T1 2004 - 2006 Pontiac GTO Re-Integration Back Into T1
#34403 from Ed Gless · Rule change · TB 23-12 (2023-12 Fastrack)
neutralPontiac GTO 2006-2009 re-integrated into T1 with LS2 at 3400 lbs, 72mm restrictor, and LS3 at 3500 lbs, 61mm restrictor.
In T1 Spec Lines, classify Pontiac GTO 2006-2009 as follows:
A specification table follows in the original; it is not shown here.
Applies to Pontiac GTO on this page: Ed Gless
GT1 Errors in GTCS Headings and Use of the Terms Category and ClassChange existing GTL and GTA Rules
#34453 from David Gomberg · Rule change · TB 23-12 (2023-12 Fastrack)
neutralGTL spec lines moved to contiguous position with GT2 and GT3; GTA category and spec lines renumbered and moved behind GTL.
from the current (or before) Table of Contents (TOC), to what is shown in the after TOC. GTL spec lines will now be contiguous with GT2 and 3 spec lines. GTA category and spec lines will be moved and renumbered behind GTL. GTA Section will not change but page numbers will, (as shown in Red italics). 9.1.2.F. GT-2, 3, LITE Category Specifications 314 GT2 Cars 327 GT2/ST 341 GT3 Cars 348
#34561 from Scotty B White · Rule change · TB 23-12 (2023-12 Fastrack)
neutralT1 Porsche 997-1 GT3 Cup added at spec line 4210, minimum weight 3050 lbs.
In T1 Spec Lines, delete the Porsche 996 GT3 Cup car from the standard spec lines and classify "Homologated car" section as follows: T1 – Homologated Cars
A specification table follows in the original; it is not shown here.
T1 C7 Corvette Rule Change Request
#34897 from Heath Karl · Rule change · TB 23-12 (2023-09 Fastrack)
neutralT1 Chevrolet Corvette C7 (14-19) including Z51, Grandsport newly classified as homologated car.
In T1 Spec Lines, classify Chevrolet Corvette C7 (14 - 19) - Includes Z51, Grandsport as follows: T1 – Homologated Cars
A specification table follows in the original; it is not shown here.
T1 Camaro Gen 5 Weight Reduction Due to Competitive Disadvantage
#35092 from Clark Nunes · Rule change · TB 23-12 (2023-09 Fastrack)
fasterT1 Gen 5 Camaro minimum weight drops 75 lbs to 3475; restrictor increases 70mm to 75mm.
In T1 Spec Lines, Gen 5 Camaro, change as follows: Spec Line 1130 - Minimum Weight "3550 3475" Spec Line 1135 - Minimum Weight "3550 3475" Restrictor Required "70mm 75mm-Flat Plate"
neutralT1 Aston Martin Vantage permitted to use OEM Sportshift II transmission.
In T1 Spec Lines, Aston Martin Vantage, add to Chassis Notes as follows: "OEM Sportshift II transmission permitted."
GT1 Request for Acceptance of Lamborghini Huracan GT3 in GT1-ST
#34929 from Michael McAleenan · Rule change · TB 24-01 (2024-01 Fastrack)
neutralLamborghini Huracan GT3 EVO(1) and GT3 added to GT1-ST at 3000 and 3100 lbs minimum weight respectively.
In GT1-ST Spec Lines, classify Lamborghini Huracan GT3 EVO(1) (2018-) as follows: GT1-ST Maximum Displacement Minimum Weight Restrictor Notes Lamborghini Huracan GT3 EVO(1) (2018-) 5204 3000 2 X39mm Per FIA Homologation GT3-040 In GT1-ST Spec Lines, classify Lamborghini Huracan GT3 (2019-) as follows:
Show 6 more lines
GT1-ST Maximum Displacement Minimum Weight Restrictor Notes Lamborghini Huracan GT3 2019- 5204 3100 52mm Per FIA Homologation GT3-040
GT1 Cylinder heads
#35040 from Pater Mumford · Rule change · TB 24-01 (2024-01 Fastrack)
neutralGT1 Trick Flow Specialties Ultra 18 Degree GM Cylinder Head Part #TFS-3181T001-CO1 allowed.
In GCR, Section 9.1.2.D.1.e.3., add at the end of section add the follows: "Trick Flow Specialties Ultra 18 Degree GM Cylinder Head assembly Part #TFS-3181T001-CO1 is allowed."
unclearT1-GT4 batch adjustments: five cars lighter, two heavier, restrictors and ECU maps changed, five models now eligible for Runoffs.
In GCR, Section 9.1.9.1.A.T., change as follows: "Tires- Tires must conform to GCR section 9.3.TIRES and als o must conform to spec line requirements. DOT approved tires are permitted. Slicks conforming to the spec line are permitted." In Touring 1 - Homologated Cars Spec Lines, 4100- BMW M2 ClubSport Racing, change Must Conform To as follows: "Tires conforming to SRO TCX rules allowed. Must meet factory specs." In Touring 1 - Homologated Cars Spec Lines, 4120- Ford Mustang FP350S 2017, change as follows: Must Conform To: "Tires conforming to Trans Am SGT tire rules allowed Must meet factory specs." Chassis Notes: "VIN not required. Additional permitted allowances: DOT tires required. Other consumables are open, alternate
Show 40 more lines
driveshaft permitted, aftermarket wheels and fuel cell per Touring category rules permitted. Shocks conforming to T1 rules permitted. Alternative rear toe links permitted." In T1-GT4 Spec Lines, change Chassis Notes as follows: Aston Martin Vantage AMR GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)** Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Audi R8 GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." BMW M4 GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Chevrolet Camaro GT4-R: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Ford Mustang GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Maclaren 570S GT4: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Mercedes AMG GT4: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Porsche 718 Cayman GT4 CS MR: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Porsche 718 GT4 RS Club-sport: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Toyota Supra GR GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." In T1-GT4 Spec Lines, change as follows: Aston Martin Vantage AMR GT4: Weight: “3575 3490” Performance Control: “SRO power level ECU Map 3 IMSA Map id 11” Chevrolet Camaro GT4-R: Weight: “3375 3435” Performance Control: “63 62mm” Ford Mustang GT4: Weight: “3550 3535” Performance Control: “63 71mm SRO compliant restrictor IMSA ECU Cal” Maclaren 570S GT4: Weight: “3450 3250” Performance Control: “SRO 2019 BOP ECU map SRO Rest 1” Mercedes AMG GT4: Weight: “3450 3470” Performance Control: “Power level 2 map 5” Porsche 718 Cayman GT4 CS MR: Weight: “3200 3250” Performance Control: “54 53.7mm” Toyota Supra GR GT4: Weight: “3350 3315”
fasterGT1, GT2, GT3, GTL, GTX rear spoiler maximum surface area limit of 295.0 square inches removed.
In GCR Section 9.1.2.G (GTA Category Specifications), change as follows: “9.1.2.G.III.I The single-plane rear spoiler must be mounted at an angel angle from 50 to 75 degrees (perpendicular to the ground being 90 degrees) and may not extend beyond the rear bumper when viewed from directly above the rear bumper. Spoilers must be a minimum of .063 aluminum or Lexan and may vary in overall height to match the contours of the bodywork. The rear spoiler dimensions shall not exceed 59.0 inches wide by 5.0 inches in height, (measured on the material surface) , or 295.0 square inches total surface area. Braces to prevent spoiler deflection are allowed, but may serve no other purpose.”
neutralT1 NEW class removes 23 spec lines including Acura NSX, Ferrari, Porsche 996, Nissan Z cars, and others; Porsche 997 spec line 1680 expiration removed.
In GCR Contents, change as follows: "9.1.9.1 TOURING (T1) CATEGORY NEW T1 NEW" In GCR, Section 9.1.9.1.Touring (T1) NEW Category Specifications, change as follows: "9.1.9.1.Touring (T1) NEW Category Specifications" In T1 NEW Spec Lines, change as follows: "9.1.9.1.A T1 NEW Spec Lines" "T1 NEW"
Show 26 more lines
In T1 NEW Spec Lines, delete the following Spec Lines in their entirety: "Acura NSX (Spec Line 1000) Acura NSX Turbo (Spec Line 1010) Acura NSX Turbo World Challenge (Spec Line 1020) Audi TTRS (GTS 2011 Spec) (Spec Line 1040) Dodge Viper ACR/ACR-X (Spec Line 1360) Ferrari 360 (Spec Line 1400) Ferrari 430 (Spec Line 1410) Ferrari 430 Challenge (Spec Line 1420) Mazda MX-5 (06-15) (Spec Line 1520 and 1530) Mazda RX-7 (Spec Line 1540) Nissan GTR (Spec Line 1550) Nissan 350/370Z (Spec Line 1560) Nissan 370Z Supercharged (Spec Line 1570) Nissan 350Z (Spec Line 1580) Nissan 350Z/370Z (Spec Line 1590) Porsche Cayman/S/GTS (05-15) (Spec Line 1600, 1610 and 1620) Porsche Cayman GTS (2011) (Spec Line 1630) Porsche 928 S4 Porsche 928 GTS-R (Spec Line 1640) Porsche 996 (Spec Line 1650) Porsche 996 TT OEM (Spec Line 1660) Subaru WRX, WRX STI (05-2020) (Spec Line 1700) Toyota Celica All-Trac (Spec Line 1710) Toyota Supra MK4 (Spec Line 1720)" In T1 NEW Spec Lines, Porsche 997, change Spec Line Number as follows: "1680 *Spec line Expires 12/23*"
GT1 GT Direct Injection allowance and rules
#35437 from Grand Touring Committee · Rule change · TB 24-02 (2024-01 Fastrack)
fasterGT1/GT2/GT3/GTL/GTX Direct Injection now permitted if OE, using only OE pump, hoses, injectors.
In GCR, Section 9.1.2.F.7.5.E. change as follows: “Direct Injection is not permitted only if it came OE and must be installed using only OE high pressure pump(s), hard and soft hoses and injectors.”
GT1 GT2/3 remove Direction Injection not allowed in Spec line notes
#35439 from Grand Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)
fasterGT2/3 Nissan, Mazda, Mitsubishi 4G93, QR25DE/DD, QE25DE/DD Direct Injection now permitted per 9.1.2.F.7.5.E.
In GT2/3 modify Spec Line notes as follows: GT2: Nissan: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” GT3: Mazda: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” Mitsubishi 4G93: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E. ” Nissan QR25DE/DD 1988cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” Nissan QE25DE/DD 2489cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.”
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
AS Request to Classify 1970-1981 Camaro and Firebird in AS
neutralChevrolet Camaro, Pontiac Firebird 70-81 Full Prep classified AS at 3400-3600 lbs with 250 lb weight reduction.
In AS Spec Lines, classify Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep as follows: AS Wheelbase Gear Ratios Std. (or Alt.) Brakes (Max) (in/mm) Weight (lbs) Notes:
A specification table follows in the original; it is not shown here.
AS Fuel Cell 12
#34194 from Clark Cambern · Rule change · TB 24-03 (2024-03 Fastrack)
neutralAS class: multiple cars gain fuel cell placement note allowing 24 inches from standard tank, unrestricted filler location.
In AS Spec Lines, add to Notes as follows: Cadillac CTS-V (04-07): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.” Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.” Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
Show 22 more lines
installation of a safety fuel cell.” Chevrolet Camaro SS (V8) (10-15): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.” Chevrolet Camaro (10-15): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.” Dodge Challenger (08-20): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.” Ford Mustang GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.” Ford Mustang Coupe GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.” Ford Mustang GT 5.0l (15-17): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.” Ford Mustang GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.”
T1 9.1.9.1 T1 new category item/ line 26 rule to expire Jan 1 2023
neutralPontiac GTO 2006-2009 LS1 added to T1 as Spec Line 1590, 5700 cc, 3400 lbs minimum.
In T1 Spec Lines, classify Pontiac GTO 2006-2009 as Spec Line Number 1590 as follows:
A specification table follows in the original; it is not shown here.
AS Please Classify the 6th Gen Into AS.
#35448 from Daniel Richardson · Rule change · TB 24-03 (2024-03 Fastrack)
neutralChevrolet Camaro 16- Full Prep classified into AS at 3400 lbs with 250 lb weight reduction.
In AS Spec Lines, classify Chevrolet Camaro (16-) Full Prep as follows: AS Wheelbase Gear Ratios Std. (or Alt.) Brakes (Max) (in/mm) Weight (lbs) Notes:
Show 4 more lines
Chevrolet Camaro (16-) Full Prep 110.6 3.42, 2.28,
A specification table follows in the original; it is not shown here.
AS spec lines
#35713 from American Sedan Committee · Rule change · TB 24-03 (2024-03 Fastrack)
neutralAS adds Ford Mustang GT 05-14 Restricted prep Engine with 62mm FPR, 3400 lbs minimum, 18-inch wheels.
In AS Spec Lines, classify Ford Mustang GT (05-14) with Restricted prep Engine as follows: AS Wheelbase Gear Ratios Std.
A specification table follows in the original; it is not shown here.
Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole
In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following: "For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190." In AS Spec Lines, Pontiac GTO (04-06), add to Notes the following: "For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."
AS Allowance of 11
#35824 from American Sedan Committee · Rule change · TB 24-04 (2024-04 Fastrack)
fasterAS Cadillac CTS-V, Chevrolet Camaro SS, Dodge Challenger, Ford Mustang GT, Pontiac GTO allowed 11" wheels until 3/1/25.
In AS Spec Lines, Cadillac CTS-V (04-07), add to Notes the following: "11" wide wheels can be used until 3/1/25." In AS Spec Lines, Chevrolet Camaro SS (V8) (10-15), add to Notes the following: "11" wide wheels can be used until 3/1/25." In AS Spec Lines, Dodge Challenger (08-20), add to Notes the following: "11" wide wheels can be used until 3/1/25." In AS Spec Lines, Ford Mustang GT 5.0l (15-17), add to Notes the following: "11" wide wheels can be used until 3/1/25."
Show 2 more lines
In AS Spec Lines, Pontiac GTO (04-06), add to Notes the following: "11" wide wheels can be used until 3/1/25."
Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole
slowerGT2-ST Acura NSX minimum weight raised to 3000 lbs, restrictor increased to 45mm TIR.
In GT2-ST Spec Lines, Acura NSX, change as follows: Minimum Weight: "2700 3000" Restrictor: "43 45mm TIR"
GT1 Camaro 1993- and 2010-
#35652 from John Bodnar · Rule change · TB 24-05 (2024-05 Fastrack)
neutralGT1 Camaro 1993-2002 classification updated; 2010- model separately classified.
In GCR, Section 9.1.2.E.1.b.3., change as follows: "Camaro (1993-2002)"
AS 6th gen Camaro limited prep
#35733 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)
neutralAS Chevrolet Camaro 1LE (2016-) classified with 3600 lbs minimum weight, 60mm restrictor, 275 tires.
In AS Spec Lines, classify Chevrolet Camaro 1LE (2016-) as follows: AS Wheelbase Gear Ratios Std. (or Alt.) Brakes (Max) (in/mm) Weight (lbs.) Notes: Chevrolet Camaro, 1LE
Show 2 more lines
(2016-) 110.6 2.66,1.78,1.30,0.74,.5 (F)
A specification table follows in the original; it is not shown here.
neutralAS Chevrolet/Pontiac Camaro & Firebird 82-92 5.7L LS1 classified at 3200 lbs with 65mm restrictor plate required.
In AS Spec Lines, classify Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves per cylinder, as follows: AS Wheelbase Gear Ratios Std.
A specification table follows in the original; it is not shown here.
AS Full Prep Head
#35891 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)
neutralAS Chevrolet Camaro, Firebird, and Ford Mustang models permitted to use Flo Tek cylinder heads.
In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (82-92), add to Notes the following: "Flo Tek Head part #102-500 are permitted." In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following: "Flo Tek Head part #102-500 are permitted." In AS Spec Lines, Chevrolet Camaro (10-15), add to Notes the following: "Flo Tek Head part #102-500 are permitted." In AS Spec Lines, Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86), add to Notes the following: "Flo Tek Part # 203-500 are permitted."
Show 4 more lines
In AS Spec Lines, Ford Mustang Including Cobra 94-04, add to Notes the following: "Flo Tek Part # 203-500 are permitted." In AS Spec Lines, Ford Mustang GT (05-14), add to Notes the following: "Flo Tek Part # 203-500 are permitted."
Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole
neutralMercedes AMG-C63 S (2023) classified in T1 with 4000 lbs minimum weight and 3700 restrictor.
In T1 Spec Lines, classify Mercedes AMG-C63 S (2023) as follows:
A specification table follows in the original; it is not shown here.
AS Request for Classification of 2018-2023 mustang In
#35764 from Michael Kamalian · Rule change · TB 24-06 (2024-06 Fastrack)
neutralAS Ford Mustang GT 5.0L (2018-) classified at 3600 lbs with 60mm restrictor, Brembo BBK permitted.
AS Spec Lines, classify Ford Mustang GT 5.0L (2018-) as follows: AS Wheelbase Gear Ratios
A specification table follows in the original; it is not shown here.
AS Mustang transmission ratios
#36662 from American Sedan Committee · Rule change · TB 24-09 (2024-09 Fastrack)
unclearAS Ford Mustang GT models gain alternate transmission ratio options for 2024-09-01.
In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Notes as follows: "Alternate transmission Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68.” In AS Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows: "Alternate transmission Ratios 3.24, 2.10, 1.42, 1.00, 0.81, .062."
Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole
GT1 Request to Classify Mazda 26B Engine
#36230 from Wayne Graham · Rule change · TB 24-09 (2024-09 Fastrack)
neutralGT1 Mazda 26B engine classified at 2850 lbs minimum weight.
In GT1 Spec Lines, GT1 Approved Automobile List, Mazda, add the following: "(Effective 11/1/2024) 26B engine = 2850 lbs."
T1 Changes to T1 Tires for GT4 and Other Cars
#35383 from Andrew Aquilante · Rule change · TB 24-12 (2024-12 Fastrack)
unclearT1 GT4 tire sizes adjusted across ten cars: most non-DOT rear to 305/660, Audi and McLaren 305/645, Camaro and Mustang 305/680.
In T1 GT4 Spec Lines, change Tire Size as follows: Aston Martin Vantage AMR GT4 4010: "315 DOT, 305/660 Non-DOT" Audi R8 GT4 - Spec Line #4020: "315 DOT, 305/645 Non-DOT" BMW M4 GT4 - Spec Line #4030: "315 DOT, 305/660 Non-DOT" Chevrolet Camaro GT4-R- Spec Line #4035: "315 DOT, 305/680 Non-DOT" Ford Mustang GT4 - Spec Line #4040: "315 DOT, 315/680 Non-DOT" Mclaren 570S GT4 - Spec Line #4050: "315 DOT, 305/645 Non-DOT" Mercedes AMG GT4 - Spec Line #4060: "315 DOT, 305/660 Non-DOT"
Show 3 more lines
Porsche 718 Cayman GT4 CS MR - Spec Line #4070: "315 DOT, 305/660 Non-DOT" Porsche 718 GT4 RS Clubsport - Spec Line #4080: "315 DOT, 305/660 Non-DOT" Toyota Supra GR GT4 - Spec Line #4090: "315 DOT, 305/660 Non-DOT"
neutralBMW M4 GT4 (G82) added to T1 GT4 at 3525 lbs minimum weight with Red power stick control.
In T1 GT4 Spec Lines, SL#4030, change as follows: Model: "BMW M4 GT4 (F82)" Performance Control: "Gold power stick Red power stick" In T1 GT4 Spec Lines, classify BMW M4 GT4 (G82) as follows:
A specification table follows in the original; it is not shown here.
GT1 Lamborghini Huracan GT3 Evo Restrictor Help
#36254 from Michael McAleenan · Rule change · TB 24-12 (2024-12 Fastrack)
fasterGT1-ST Lamborghini Huracan GT3 Evo and 2019+ GT3 both shift to Unrestricted from 39mm and 52mm restrictors.
In GT1-ST Spec Lines, Lamborghini Huracan GT3 EVO(1) (2018-), change Restrictor as follows: "2 X 39mmUnrestricted" In GT1-ST Spec Lines, Lamborghini Huracan GT3 (2019-), change Restrictor as follows: "52mm Unrestricted"
T1 Alt. Clutch Allowance
#36606 from Hugh Stewart · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT1 Spec Lines now permits 5.5 inch clutch in Engine Notes.
In T1 Spec Lines, SL# 1050, change add to Engine Notes the following: "5.5 inch clutch permitted."
T1 BOP Changes Need Updates
#36667 from Joe Rainey · Rule change · TB 24-12 (2024-12 Fastrack)
fasterT1 GT4 Spec Line 4020 restrictor opens from 44mm to 45mm, minimum weight drops to 3400 lbs.
In T1 GT4 Spec Lines, Spec Line 4020, change as follows: Performance Control: Power level 2020, 44mm 45mm SRO compliant restrictor" Min. Weight with driver (LBS): "3550 3400"
T1 Request Ford Performance Darkhorse R in T1
#37136 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)
neutralMustang Darkhorse R added to T1 homologated cars at 3,250 lbs minimum with 305/315 tires, ineligible for Runoffs until 3 Super Tour events.
In T1-Homologated Cars Spec Line, classify Mustang Darkhorse R (Mustang Challenge) as follows: T1 – Homologated Cars
A specification table follows in the original; it is not shown here.
T1 Car Mods for T1 Corvette under line item 1150
#37173 from Thomas Napolitano · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT1 Corvette may roll or flatten wheel opening lips for tire clearance; plastic fenders may remove lips if edge thickness matches basic material.
In GCR, Section 9.1.9.1.A.2,, add the following: "It is permitted to roll under or flatten any interior lip on the wheel opening for tire clearance. Cars with plastic/composite fenders may remove any interior wheel opening lip, but the resulting material edge shall be no thinner than the basic fender material thickness. Non-metallic inner fender liners may be removed. Vents may be added to fenders."
T1 Increased Bore Throttle Bodies for E46 M3 S54 Engine
#37273 from Mark Pfeffer · Rule change · TB 24-12 (2024-12 Fastrack)
fasterT1 E46 M3 S54 can now use Dinan Throttle Body #D760-3400 on 3.250L engine.
In T1 Spec Lines, E46 M3 Spec Line # 1050, add to Engine Notes the following: "Dinan Throttle Body #D760-3400 allowed on the 3.250L."
fasterAS Ford Mustang Coyote engines increase restrictor to 80mm from 64mm or 67mm.
In AS Spec Lines, add to Notes as follows: Ford mustang (GT 05-14): "Gen 1- 67mm Gen 2-64mm" Ford mustang (GT 05-14): "Gen 1- 67mm" Ford mustang (GT 15-17): "Gen 1- 67mm" Ford mustang (GT 94-04): "Gen 1- 67mm Gen 2-64mm" Ford mustang cobra & Cobra R Mercury Capri (79-93) (79-86): "Gen 1- 67mm Gen 2-64mm"
AS Performance Pack for 2015+ Mustang
#36867 from Michael Kamalian · Rule change · TB 25-01 (2025-01 Fastrack)
fasterAS Mustang GT 05-14 4.6L loses 300 lbs; 15-17 and 2018+ models lose 61mm and 60mm restrictors respectively.
In AS Spec Lines, Ford Mustang Coupe GT (05-14) Restricted Prep., change Notes as follows: "The 4.6L engine assembly has a weight reduction of 300 lbs. 5.0L/6spd engine/trans: track pack front and rear spoiler allowed." In AS Spec Lines, Ford Mustang Coupe GT (05-14) with Restricted Prep. engine, change Notes as follows: "Max. Wheel Size: Dia.18.0 inches. Stock brakes or alternate Ford 14” Brembo Brake (Ford Racing Kit #M-2300-S) and full prep brake package may be used. Either engine may be used. 1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Cold Air Intake allowed Charge Motion Control Valves can be blocked off and removed for firewall clearance Allow Cold Air Intake Tremec Magnum transmission may be used P/N- TUKT16901. Full Prep Transmissions rule package may also be used. Max compression ratio, 11.2:1 track pack front and rear spoiler allowed. Alternate transmission
Show 10 more lines
Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68." In AS Spec Lines, Ford Mustang GT 5.0l (15-17) Restricted Preparation, change Notes as follows: "Max. Wheel Size: Dia. 18.0 inches. Stock brakes or alternate Ford Brembo Brake caliper (Ford Racing Kit #M-2300-S) may be used. 61mm flat plate restrictor required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. 11” wide wheels can be used until 3/1/25. Performance pack front and rear spoiler, body kit allowed." In AS Spec Lines, Ford Mustang GT 5.0L (2018-), change Notes as follows: "Package Brembo front BBK and 380mm rotors permitted (Ford PN M-2300-V) at no weight penalty. 60mm flat plate restrictor required. 2014 Mustang GT exhaust manifolds permitted. Ford Racing oil pan #M-6675-M50BR permitted. Alternate transmission Ratios 3.24, 2.10, 1.42, 1.00, 0.81, .062. Performance pack front and rear spoiler, body kit allowed."
Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole
GT1 Addition of a limited prep LS Chevy engine for GT1
#37045 from Robert Logsdon · Rule change · TB 25-01 (2025-01 Fastrack)
In GCR, Section 9.1.2. GT1 Spec Lines, GT1 Approved Automobile List, LS1 V8 engine allowed with stock intake, add the following: "LS1 Limited Prep GT1 motor 2600 # with driver Blocks : GM castings or aftermarket, no lightening, Max volume 383 cubic inches Cylinder Heads: GM LS castings or aftermarket, stock valve angle, intake and exhaust ports must be in stock location, porting and polishing allowed Valves: No titanium valves, must be stock size for head part number
Show 12 more lines
Rockers: Factory 1.7 rockers only, aftermarket trunion mod allowed Pushrods: Free Intake manifold: stock EFI for variant used or GM 525 carb intake or Edelbrock carb variants ie: Performer RPM, Victor, Victor Jr. or similar. Camshaft: Hydraulic roller only, standard journal size, lift and duration free Timing chain: single or double roller type only water pump: stock or aftermarket in stock location Harmonic dampener: SFI approved, Pistons: Factory or aftermarket flat top pistons only, valve reliefs allowed, coatings allowed Crankshaft: Factory or forged steel aftermarket, 50 lb min. weight Rods: GM stock or aftermarket forged steel Carburetor: one 4150 type 750 cfm max"
AS Gear Ratios
#37131 from Timothy White · Rule change · TB 25-01 (2025-01 Fastrack)
neutralAS class gear ratio options specified for multiple American muscle cars, including Cadillac CTS-V, Chevrolet Camaro, Ford Mustang, Dodge Challenger, and Pontiac GTO.
In AS Spec Lines, change Gear Ratios as follows: Cadillac CTS-V (04-07): "2.97, 2.07, 1.43,1.00, 0.84,0.56 or 3.01, 2.07, 1.43, 1.0, .84, .57 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00" Chevrolet Camaro, Pontiac Firebird (70-81), Full Prep: "3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00" Chevrolet Camaro, Pontiac Firebird (70-81), Restricted Prep.: "3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00" Chevrolet/Pontiac Camaro & Firebird (82-92) Full Prep:
Show 42 more lines
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00" Chevrolet/Pontiac Camaro & Firebird (93-02) Full Prep: "3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00,0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 or 2.20,1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81" Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted prep: "2.97, 2.07, 1.43, 1.00, 0.80, 0.62 or 3.36, 2.07, 1.35, 1.00, .80, .62 or 2.66, 1.78, 1.30, 1.00, 0.74, 0.50 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00" Chevrolet Camaro SS (V8) (10-15) Restricted Prep: "3.01, 2.07, 1.43, 1.0, .84, .57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00" Chevrolet Camaro (10-15) Full Prep: "3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00, 0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81" Chevrolet Camaro (16-) Full Prep: "3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00, 0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81" Chevrolet Camaro, 1LE (16-): "2.66,1.78,1.30, 0.74,.50 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00" Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2 valves/cylinder: "2.97, 2.1, 1.46, 1.00, 0.74, 0.50 or 2.26, 1.58, 1.19, 1.00, 0.77, 0.63 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00" Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) Full Prep: "3.07, 1.72, 1.00, 0.70 or 2.95, 1.94, 1.34, 1.00, 0.63 or 3.35, 1.99, 1.33, 1.00, 0.68 or 2.87 1.89 1.28 1.00 0.81" Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) with Restricted Prep Engine: "2.95, 1.94, 1.34,1.00, 0.63 or 3.35,1.99,1.33, 1.00, 0.69 or 2.88, 1.91, 1.33, 1.00 or 3.27,1.98, 1.34, 1.00, 0.68, 3.66, 2.43, 1.69, 1.32, 1.00, .68. or 2.87,1.89,1.28,1.00,.81" Ford Mustang Including Cobra 94-04 Full Prep: "3.07, 1.72, 1.00, 0.70 or 2.95, 1.94, 1.34, 1.00, 0.63 or 3.35, 1.99, 1.33, 1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 or 2.20, 1.64,1.28,1.00 or 2.87 1.89 1.28 1.00 0.81" Ford Mustang Cobra and GT 94-95 (Restricted Prep): "3.35, 1.99, 1.33, 1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00" Ford Mustang including Cobra 96-04 (Restricted Prep) 4.6L two and four valve motor: "3.35, 1.99, 1.33, 1.00, 0.68 or 3.27, 1.98, 1.34, 1.00, 0.67 or 3.37, 1.99, 1.33, 1.00, 0.68 or 3.38, 2.00, 1.32, 1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00" Ford Mustang GT (05-14) Full Prep: "3.38, 2.00, 1.32, 1.00, 0.68 or 3.66, 2.43, 1.69,1.32, 1.00, 0.65 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00" Ford Mustang GT 5.0l (15-17) Restricted Preparation: "3.66, 2.43, 1.69,1.32, 1.00, .65 or 4.69, 2.98,2.14, 1.76,1.52, 1.27,1.00, 0.85, 0.68, 0.63, or 3.24, 2.10, 1.42, 1.00, 0.81, .062. or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00" Ford Mustang GT 5.0L (2018-) Restricted Preparation: "2.97, 2.07, 1.43, 1.00, 0.84, 0.57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00" Pontiac GTO (04-06) Restricted Prep. "2.97, 2.07, 1.43, 1.00, 0.84, 0.57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
GT1 Correct language regarding OEM Areo Devices
#37137 from Christopher Childs · Rule change · TB 25-01 (2025-01 Fastrack)
In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows: "B. Aerodynamic Devices 2. Rear wing c. The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule."
A specification table follows in the original; it is not shown here.
AS ECU specs for LS engine
#37208 from Gary Mathews · Rule change · TB 25-01 (2025-01 Fastrack)
In AS SPEC LINES, Cadillac CTS-V (04-07) Restricted Prep., change Notes as follows: "Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Tremec TR6060 Transmission with 3.0 1, 2.07, 1.43, 1.0, .84, .57 ratios permitted. 11” wide wheels can be used until 3/1/25. Any ECM may be used." In AS SPEC LINES, Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep ., add to Notes as follows: "Any ECM may be used." In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1, add to Notes as follows:
Show 14 more lines
"Any ECM may be used." In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep.5.7L V-8 LT1, add to Notes as follows: "Any ECM may be used." In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep. 5.7L V-8 LT1; 98-02 , change Notes as follows: "5.7L LS1: GM Performance Parts camshaft Kit P/N-19355738 is permitted. Cylinder Bore, 99 mm; Stroke, 92 mm; Intake Valve Diameter, 50.8; Exhaust Valve Diameter, 39.4 mm; Throttle Body Bore, 75 mm; SLP Intake Lid (SLP part number 21044 (98-99) and 21045 (00-02)) is permitted. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. 1-3/4 headers allowed. For the LS1connecting rods Callies P/NCSC6100DS6A2AH, Scat rods P/N2-1CR6100-944, GM performance rods P/N12649190. Any ECM may be used." In AS SPEC LINES, Chevrolet Camaro SS (V8) (10-15) Restricted Prep., add to Notes as follows: "Any ECM may be used."
GT1 GT1-ST Adjustments
#37481 from Grand Touring Committee · Rule change · TB 25-01 (2025-01 Fastrack)
unclearGT1-ST restrictor sizes removed for 13 cars; new specs not printed in letter.
In GT1-ST SPEC LINES, change as follows: Aston Martin Vantage GT3 (2012) : Restrictor: "2 x 41.5mm" Audi R8 LMS Ultra GT3 (10-14) : Restrictor: "2 x 49mm" BMW Z4 GT3 (10-13): Restrictor: "70mm" Chevrolet Corvette C8 (20-):
Show 23 more lines
Restrictor: "71mm- Flat Plate" Dodge Viper GT3R (2012-): Restrictor: "2 x 40mm" Dodge Viper, incl Comp Coupe, ACR/ACR-X Max Displacement 8400, Weight 3200: Restrictor: "68mm flat plate" Ferrari 458 GT3 (2011-): Restrictor: "2 x 43mm" Lamborghini Gallardo GT3 (2013): Restrictor: "2 x 47mm" Lamborghini Huracan GT3 EVO(1) (2018-): Restrictor: "2 X39mm" McLaren MP12C GT3 (2013-): Restrictor: "2 x 36mm 1.50 bar" Lamborghini Huracan GT3 (2019-): Restrictor: "2 x 40 mm" McLaren MP12C GT3 (2013-): Restrictor: "2 x 40 mm" Mercedes Benz SLS GT3 (2011-): Restrictor: "2 x 36 mm" Porsche 991 GT3-R (2016): Restrictor: "(2) 35 mm" Porsche 997 GT3 R (2013-): Restrictor: "65mm"
T1 T1 Parity Compared to GT4
#37170 from Tony Ave · Rule change · TB 25-02 (2025-02 Fastrack)
slowerT1 Mustang gains 125 lbs to 3600, restrictor shrinks 65mm to 60mm. Corvette gains 50 lbs to 3500, restrictor shrinks 70mm to 67mm. BMW deleted.
In T1 Spec Lines, change Weight and Restrictor Required as follows: Mustang - Spec Line 1430 Weight: "3475 3600" Restrictor Required: "65mm 60mm - FPR" Corvette Spec Line 1190 Weight: "3450 3500" Restrictor Required: "70mm 67mm - Flat Plate" In T1 Spec Lines, delete Spec Line BMW # 1190 in its entirety.
T1 Clarification of Request Approval #37273
#37399 from Mark Pfeffer · Rule change · TB 25-02 (2025-02 Fastrack)
unclearT1 E46 M3 Spec Line 1050 allows VAC Motorsports throttle body VAC-TB-S54 on 3.250L engine instead of Dinan.
In T1 Spec Lines, E46 M3 Spec Line # 1050, change Engine Notes as follows: "Dinan Throttle Body #D760-3400 VAC Motorsports #VAC-TB-S54 allowed on the 3.250L."
neutralAcura NSX GT3 EVO 22 classified in GT1 with 3500cc twin turbo V-6, 3100 lbs, max RPM 7500.
In GT1 Spec Lines, GT 1 Cars - ACURA, classify Acura NSX GT3 EVO 22 as follows: GT 1 Cars - ACURA Model Years Body Style Drive- line Wheel- base (in) Notes Acura NSX GT3 EVO 22 N/A 2dr RWD 103.5 Ground Clearance 50mm
Show 5 more lines
In GT1 Spec Lines, GT 1 Engines - ACURA, classify Crossflow V-6 as follows: GT 1 Engines - ACURA Engine Family Engine Type Bore x
A specification table follows in the original; it is not shown here.
unclearT1 Mustang Spec 1430 restrictor opens 60mm to 65mm; Spec 1460 weight rises to 3500 lbs, restrictor 70mm; Corvette 1190 restrictor opens 67mm to 70mm; BMW 1090 restrictor narrows 40mm to 35mm; BMW 1100 weight rises to 3350 lbs.
In T1 Spec Lines, change Weight, Restrictor Required and/or Notes as follows: Mustang - Spec Line 1430: Restrictor Required: "60mm 65mm - FPR" Mustang - Spec Line 1460: Weight: "3425 3500" Restrictor Required: "70mm - FPR" Corvette Spec Line 1190: Restrictor Required: "67mm 70mm - Flat Plate"
Show 5 more lines
BMW - Spec Line 1090: Required Restrictor: "(2) X 40mm 35mm diameter hole inlet restrictor plate required" Chassis Notes: "This spec line is set to expire 12/31/25." BMW - Spec Line 1100: Minimum Weight: "3150 3350”
FA Update Formula Renault 2.0 spec line notes
#37853 from Club Racing Board · Rule change · TB 25-03 (2025-03 Fastrack)
neutralFA Formula Renault 2.0 (10-17) spec notes clarified: engine sealed, manual compliance required, tire choice unrestricted, no alterations except repairs.
In FA Table 2, Formula Renault 2.0 (10-17) spec line, change the notes as follows: "Engine must remain sealed. Car must comply with year-specific Formula Renault 2.0 manual, technical regulations, and all applicable bulletins found here:. Competitors must have copies of these materials in their possession and present them upon request. https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/bulletins-techniques/2017, https://sites.google.com/a/renault-sport.com/formule-renault-2-0-en/manuel-d-utilisateur/2017. The following exceptions apply: Tire choice is unrestricted. No part of the car may be altered from original Formula Renault 2.0 components, except for necessary repairs that do not affect performance."
AS Race memo
#37902 from American Sedan Committee · Rule change · TB 25-03 (2025-03 Fastrack)
unclearAS Spec Lines removes ECM flexibility restriction from five Cadillac and Chevrolet/Pontiac V8 models.
unclearAS Flotek Head plunge cut dimensions figure updated in GCR Section 9.1.6.
In GCR, Section 9.1.6., replace Figure 1 Value Seat Cutting Dimensions with the following:
AS Notes clean up
#37693 from American Sedan Committee · Rule change · TB 25-04 (2025-04 Fastrack)
neutralAS class notes cleanup: multiple Camaro, Firebird, CTS-V, Challenger, Mustang specs and fuel cell/ECM/head restrictions removed.
In AS Spec Lines, change/add to Notes as follows: Cadillac CTS-V (04-07): "Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used. The Drive Shaft Shop, Axle shaft part #'s 510220/510221 permitted." Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep: "Engine built to A/S Build Sheet specifications with the following: Head Casting #s: 14101081, 14014416 Port Volume (Max.): 081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb. weight reduction. Edelbrock Cylinder Head Part
Show 88 more lines
#s 608979, 608879." Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep.: "Any ECM maybe used." Chevrolet/Pontiac Camaro & Firebird (82-92) Full Prep.: "Engine built to A/S Build Sheet specifications with the following: Head Casting #s: 14101081, 14014416 Port Volume (Max.): 081 cast¬ing: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb weight reduction. Edelbrock Cylinder Head Part #s 608979, 608879 are permitted. For regional competition only, unmodified GM Performance cylinder head part #s 19300955, 19300956 may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186 installed between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on each side of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Flo Tek Head part #102-500 are permitted." Chevrolet/Pontiac Camaro & Firebird (82-92) Restricted prep engine: "Any ECM maybe used." Chevrolet/Pontiac Camaro & Firebird (93-02) Full Prep: "Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.): 081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb weight reduction. Edelbrock Cylinder Head Part #’s 608979, 608879 are permitted. For regional competition only, unmodified GM Performance cylinder head part #s 19300955, 19300956 may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186 installed between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on each side of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Flo Tek Head part #102-500 are permitted." Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep: "Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used." Chevrolet Camaro SS (V8) (10-15) Restricted Prep: "Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used." Chevrolet Camaro (10-15) Full Prep: "Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.): 081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 200 lb weight reduction. Edelbrock Cylinder Head Part #’s 608979, 608879 are permitted. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Fuel cells must be located within 24 inches of the standard tank. The 24-inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Flo Tek Head part #102-500 are permitted. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell." Chevrolet Camaro (16-) Full Prep: "Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.): 081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 200 lb weight reduction. Edelbrock Cylinder Head Part #’s 608979, 608879 are permitted, Flo Tek Head part #102-500 are permitted." Chevrolet Camaro, 1LE (16-): "60mm flat plate restrictor required. Any ECM maybe used." Dodge Challenger (08-20) Restricted Preparation: "80mm flat plate restrictor is required on the 6.4L engine. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell." Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) Full Prep: "Engine built to A/S Build Sheet specifications with the following: Head Casting #s: F3ZE AA (GT40), F1ZE-AA (GT-40), F77E-AA (GT- 40P), Port Volume (Max.): 143.00cc IN/54.00cc EX (GT-40 & GT-40P) with a 250 lb weight reduction. Edelbrock Cylinder Head Part #s 602579, 602479 are permitted. For regional competition only, unmodified Ford Performance cylinder head part #s M-6049-Z304DA7, M-6049-Z304D may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186 installed between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on each side of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Flo Tek Part # 203-500 are permitted." Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri(79-86) with Restricted Prep Engine: "62mm flat plate restrictor is required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted." Ford Mustang Including Cobra 94-04 Full Prep: "Engine built to A/S Build Sheet specifications with the following: Head Casting #s: F3ZE AA (GT40), F1ZE-AA (GT-40), F77E-AA (GT- 40P), Port Volume (Max.): 143.00cc IN/54.00cc EX (GT-40 & GT-40P) with a 250 lb weight reduction. Edelbrock Cylinder Head Part #s 602579, 602479 are permitted. For regional competition only, unmodified Ford Performance cylinder head part #s M-6049-Z304DA7, M-6049-Z304D may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186 installed between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on each side of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Flo Tek Part # 203-500 are permitted." Ford Mustang GT (94-04) with Restricted Prep Engine: "MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted." Ford Mustang Cobra and GT 94-95(Restricted Prep): "1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted." Ford Mustang including Cobra 96-04 (Restricted Prep): "1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted." Ford Mustang Coupe GT (05-14) Restricted Prep.: "1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted. MT82 6 speed is permitted." Ford Mustang GT (05-14) with Restricted Prep Engine: "1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted. MT82 6 speed is permitted." Ford Mustang GT 5.0l (15-17) Restricted Preparation: "61mm flat plate restrictor required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted." Ford Mustang GT 5.0L (2018-): "60mm flat plate restrictor required. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
neutralCadillac CT4-V Blackwing added to T1 Spec Line 1115, 3564cc, 3750 lbs minimum weight.
In T1 Spec Lines, classify Cadillac CT4-V Blackwing as follows:
A specification table follows in the original; it is not shown here.
T1 Acceptance of Porsche 981 GT4 Clubsport into T1
#36664 from John Brown · Rule change · TB 25-05 (2025-05 Fastrack)
neutralPorsche 981 GT4 Clubsport added to T1 as spec line 4085, minimum weight 3100 lbs with driver.
In T1-GT4 Spec Lines, classify Porsche 981 GT4 Clubsport as follows:
A specification table follows in the original; it is not shown here.
T1 Request to Restore T1 Honda S2000 to Proper Weights
#37644 from David Mead · Rule change · TB 25-05 (2025-05 Fastrack)
fasterT1 Honda S2000 minimum weight reduced from 2950 lbs to 2900 lbs.
In T1 Spec Lines, Honda S2000, Spec Line 1530, change as follows: Minimum Weight: "2950 2900" Chassis Notes: "This spec line is set to expire as of 12/31/2025 if not represented in Majors competition in 2025."
T1 DCT Transmission in E46
#37964 from Matt Spicuzzi · Rule change · TB 25-05 (2025-05 Fastrack)
neutralT1 BMW E46 M3 permits BMW #GS7D36SG aftermarket sequential transmission in SL# 1060 and 1070.
In T1 Spec Lines, BMW E46 M3, add to Chassis Notes the following: SL# 1060: "BMW #GS7D36SG transmission permitted as an aftermarket sequential option." SL# 1070: "BMW #GS7D36SG transmission permitted as an aftermarket sequential option."
Applies to BMW M3 on this page: Ian Barberi
AS Errors and Omission
#38055 from American Sedan Committee · Rule change · TB 25-05 (2025-05 Fastrack)
slowerAS Ford Mustang GT 5.0L (15-17) flat plate restrictor reduced from 67mm to 64mm.
In AS Spec Lines, Ford Mustang GT 5.0l (15-17), Flat Plate Restrictor Size, change as follows: "67mm 64mm"
T1 Reduce E92 M3 Minimum Weight to 3050
#38092 from Shane Brown · Rule change · TB 25-05 (2025-05 Fastrack)
fasterT1 BMW M3 E92 minimum weight reduced to 3300 lbs.
In T1 Spec Lines, BMW M3 E92 (08-13), Spec Line 1100, change Min. Weight as follows: "3350 3300"
fasterT1 Mustang Darkhorse R gets 315 front and rear tyres, loses 500 lbs minimum weight to 3600.
In T1 Spec Lines, Mustang Darkhorse R (Mustang Challenge) Spec Line- 4119, change as follows: Tire size: "305 315 (f) 315(r)" Performance Control: "TBD" Min. Weight with driver (LBS): "10.5 (f) 11 (r) 3600" Chassis Notes: "Must conform to Mustang Challenge Rules. Tires conforming to Mustang Challenge rules are permitted. **This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
AS Request to Add LS1/LS6 Intakes for 5.3L Truck Engine EnO
#38197 from Jim Clark · Rule change · TB 25-05 (2025-05 Fastrack)
neutralAS LS1/LS6 5.3L truck engine gains four approved intake part numbers: 12561269, 88894095, 89017363, 89017364.
In GCR, Section 9.1.6.F., add the following to Intake Part #’s: "17113697, 19418185, 89017230, 89017363, 89017364, and 89017365, 12561269 and 88894095"
AS Errors and Omissions
#38234 from American Sedan Committee · Rule change · TB 25-06 (2025-06 Fastrack)
neutralAS Ford Mustang GT 05-14 Restricted Prep Engine gains alternative gear ratios: 3.66, 2.43, 1.69, 1.32, 1.00, .65
In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Gear Ratios the following: "or 3.66, 2.43, 1.69, 1.32, 1.00, .65"
Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole
AS RE: Previous Letter 37695 Update
#38245 from Michael Kamalian · Rule change · TB 25-07 (2025-07 Fastrack)
fasterAS Ford Mustang GT 5.0 2018- weight reduced from 3600 to 3525 lbs.
In AS Spec Lines, Ford Mustang GT 5.0 (2018-), change Weight as follows: "3600 3525"
Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe
FA Ligier JS F3 Tire Choice
#38434 from Rocco Magni · Rule change · TB 25-07 (2025-07 Fastrack)
neutralFA Ligier JS F3 front tires may be Hoosier 43363 240/580R13 MS, rear 43368 300/590R13 MS.
In FA Table 2, FR Americas Ligier JS F3 spec line, change the notes as follows: "Engine must be sealed in compliance with FR Americas or prior F3 Americas requirements. Car must comply with FR Americas rules, with the following exception: front tires may be Hoosier P/N 43363, size 240/580R13 in MS compound, and rear tires may be Hoosier P/N 43368, size 300/590R13 in MS compound. Competitors must have current copies of Formula Regional Americas Championship Sporting Regulations, Onroak Automotive Ligier JS F3 Information Manual, and HPD engine-related specifications and instructions in their possession and present them upon request."
GT1 Correction to Limited prep LS Chevy engine for GT1
#38902 from Robert Logsdon · Rule change · TB 25-09 (2025-09 Fastrack)
neutralGT1 LS Limited Prep Engine expands to include LS1, LS2, LS3, LS6 with 11:1 max compression.
In GCR, Section 9.1.2. GT1 Spec Lines, GT1 Approved Automobile List, LS1 engine allowed with stock intake, make the following change: "LS1 Limited Prep GT1 Motor Chevy LS Limited Prep Engine including LS1, LS2, LS3 and LS6." "Pistons: Factory or aftermarket flat top pistons only, valve reliefs allowed, coatings allowed. Maximum compression ratio 11:1."
GT1 RM 25-06 GT1 reclassify the Acura NSX GT3 EVO 22 to GT1-ST
#39101 from Club Racing Board · Rule change · TB 25-10 (2025-10 Fastrack)
neutralAcura NSX GT3 EVO 22 reclassified from GT1 to GT1-ST with 3100 lbs minimum weight.
IN GT1 reclassify the Acura NSX GT3 EVO 22 to GT1-ST as follows: GT1 Approved Automobile List Make/Model Wheelbase ACURA NSX GT3 EVO 22 103.5” DOHC 4v per cylinder EFI Twin Turbo Crossflow V-6 Displacement 3500cc Bore and Stroke 91x90 MAX RPM 7500 MAX BOOST 2.1 bar Weight 3100 lbs GT1-ST Maximum
Show 4 more lines
Displacement Minimum Weight Restrictor Notes ACURA NSX GT3 EVO 22 3500cc 3100 Per FIA Homologation GT3-047
AS Cadillac CTS-V BOP Weight Change
#38640 from Alex Lozano · Rule change · TB 25-09 (2025-09 Fastrack)
neutralFA class adds USF Pro 2000 car eligibility for Formula Atlantic racing.
Effective 11/1/25 in FA Table 2, add the following:
AS 1994 Mustang Spec Line Request
#39104 from Barry Borgschatz, Jr · Rule change · TB 25-12 (2025-12 Fastrack)
unclearAS Ford Mustang GT 94-04 Restricted Prep Engine now permits Ford Motorsport M-6250-F303 camshaft.
In AS Spec Lines, Ford Mustang GT(94-04) with Restricted Prep Engine, add to notes the following: "Ford Motorsport #M-6250-F303 camshaft is permitted."
Applies to Ford Mustang on this page: Roger Eagleton, Ross Murray, Matt Lituchy, Michael Lowe, Pratt Cole
T1 Keep S2000 Classification
#39344 from David Mead · Rule change · TB 25-12 (2025-12 Fastrack)
unclearUnable to summarize: letter states intent but provides no actual rule changes to S2000 specification.
neutralT1 BMW M3 E92 (08-13) Spec Line 1090 removed entirely.
In T1 Spec Lines, BMW M3 E92 (08-13) Spec Line number 1090, delete Spec Line in its entirety.
FA Alternate Intake Manifold for MZR
#38223 from Ove Olsson · Rule change · TB 26-01 (2026-01 Fastrack)
unclearFA MZR gains alternate Noor P/N 0088-8-00 intake manifold with AT Power runners as option to Elan or Mazda Speed Elite.
In FA, GCR section 9.1.1.2.d, modify as follows: "9. Intake manifold must be unmodified Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT, 1.882” maximum bore diameter at throttle plates. Elan or Mazda Speed equivalent Elite intake manifold may be replaced with unmodified intake Noor P/N 0088-8-00 with intake runners AT Power P/N 13624." "10. Elan DP02-60-003 or Mazda Speed equivalent Elite USF2015AT intake manifold must use an A aluminum spacer must be used between the intake manifold and cylinder head castings; minimum spacer length is 2.200”."
fasterFA Formula 1000 motorcycle-based engine loses maximum compression ratio 14.5:1 limit.
In FA Table 2, Formula 1000 spec line, change the Engine as follows: "Motorcycle-based 4-cycle up to 1000cc, maximum compression ratio 14.5:1;. o Otherwise, current FA engine rules apply."
GT1 NSX Parity With Other GT3s Let Alone a GT1 Car
fasterGT1-ST Acura NSX GT3 EVO 22 weight drops 100 lbs to 3000 lbs.
In GT1-ST, Acura NSX GT3 EVO 22, change Weight as follows: "3100 3000"
AS Restrictor Plate Change for Gen 2 Ford Coyote Engine
#39501 from American Sedan Committee · Rule change · TB 26-01 (2026-01 Fastrack)
slowerAS Ford Mustang Restricted Prep engines lose 3 mm restrictor plate, from 64 mm to 61 mm.
In AS Spec Lines, change Restrictor as follows: Ford Mustang Incl. Cobra and Cobra R (79-93) and Mercury Capri (79-86) with Restricted Prep Engine: "64 mm 61 mm" Ford Mustang GT (94-04) with Restricted Prep Engine: "64 mm 61 mm" Ford Mustang Coupe GT (05-14) Restricted Prep 5.0L/6 speed 4 valves per cylinder: "64 mm 61 mm" Ford Mustang GT (05-14) with Restricted Prep Engine: "64 mm 61 mm" Ford Mustang GT 5.0L (15-17) Restricted Preparation: "64 mm 61 mm"
unclearT1 Spec Line restrictor changes from 70mm flat plate to unspecified new specification.
In T1 Spec Line, Spec line # 1132, change Restrictor as follows: "70mm - Flat Plate"
FA Change Formula 1000 allowances
#39608 from Club Racing Board · Rule change · TB 26-01 (2026-01 Fastrack)
fasterFA Formula 1000 allows carbon fiber external panels, forward-facing gaps, raises floor to 125mm, adds eight 75×125mm rub blocks, expands diffuser to 110cm with 75mm radius transitions.
In FA Table 2, Formula 1000 spec line, change the Notes as follows: "Car must comply with December 2019 GCR Formula 1000 (FB) Preparation Rules, https://www.scca.com/downloads/48184- gcr-december-2019/download, except as modified by this spec line. The prohibition of using carbon fiber in any external panels or any panels licked by the airstream in Part 3.C of the December 2019 GCR F1000 (FB) Preparation Rules is removed, with the exception that the car's floor pan/undertray must comply with the requirements of Part 2.D of the December 2019 GCR F1000 (FB) Preparation Rules. The prohibition of forward-facing gaps or openings in the bodywork in Part 3.I of the December 2019 GCR F1000 (FB) Preparation Rules is removed. Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is modified as follows: "Between the rear of the front tire and the front of the rear tire, no point on the lower surface of the car (the surface
Show 7 more lines
licked by the air stream) shall be more than 125mm above the plane determined by the reference area designated by the entrant and on a line perpendicular to that reference plane." Part 3.D of the December 2019 GCR F1000 (FB) Preparation Rules is also modified as follows: "A maximum of eight (8) rub blocks of maximum dimension 75mm by 125mm are allowed anywhere on the lower surface of the chassis and may extend below the reference plane." Part 3.E of the December 2019 GCR F1000 (FB) Preparation Rules is modified as follows: "The radius of transitions between the diffuser sides and adjacent horizontal structures may be up to 75mm. The width of the diffuser, as measured between its sides and above any radiused transitions, may not exceed 110cm in any lateral section." The CRB may require the use of Flat Plate Intake Restrictors at any time."
AS Edelbrock manifold (& timing kit) to Chevy LS Spec Lines Request
#39055 from Jason Smith · Rule change · TB 26-01 (2026-01 Fastrack)
neutralAS Chevy LS adds Edelbrock Performer RPM 71187 intake manifold with MSD 6014 ignition and 4776 Holly carburetor as spec line option.
In GCR, Section 9.1.6.D.2.h.2., add the following: "(Effective 2/1/2026) i. Weight based on full preparation chassis choice spec line for GM LM7 5.3L Carburetor Option: Must use the full prep 4776 holly carburetor and spacer gasket Edelbrock Performer RPM 71187 intake manifold MSD 6014 ignition box (Edelbrock part # kit 7118)"
GT1 Request for Addition of Porsche 992.1 GT3 Cup into GT1
#39322 from Erik Madsen · Rule change · TB 26-02 (2026-02 Fastrack)
neutralGT1 adds Porsche 992.1 GT3 Cup (2022-2025) with OEM ABS, traction control, RSR bumper, canards, and any exhaust allowed.
In 9.1.2. GT1 Spec Lines, add the following: "992.1 GT3 Cup (2022-2025) OEM ABS and Traction Control allowed. Porsche OEM RSR bumper and canards allowed. Any exhaust system may be utilized."
FA Pro Mazda Classification and Performance Enhancement Proposal
#39411 from Stephen Lamana · Rule change · TB 26-02 (2026-02 Fastrack)
fasterFA Pro Mazda: lower intake manifold now unrestricted, throttle body raised to 80mm, wing height must not exceed 99cm, bodywork width must not exceed 132cm.
In FA Table 2, Pro Formula Mazda spec line, change the notes as follows: "All current FA rules apply to areas not covered by this spec line. Apex seals unrestricted. Street port or bridge port allowed. Unmodified OEM l Lower intake manifold required unrestricted, upper intake manifold unrestricted. Balance tube not permitted. Fuel injection only. Maximum 70 80mm T throttle B body. The maximum height of the wing and/or endplates shall must not exceed 99cm (38.98 inches). The overall maximum width of the bodywork behind the front wheels shall must not exceed 132cm (51.97 inches)."
T1 LS1 into Corvette C6 Spec Line Request
#39716 from Danny Kellermeyerhttps://crbscca.com/secu · Rule change · TB 26-02 (2026-02 Fastrack)
In T1 Spec Lines, reinstate Spec Line # 1139, Chevrolet Corvette C6 (05-13) Includes Z51, GrandSport, Z06, Z06 Carbon, as follows: Max Displ: "LS1, LS6 OEM" Min Weight: "3200" Required Restrictor: "70mm"
What the rules allowed changed as listed; this does not say what any particular car ran.