This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One run is left out as not that car's own laps (far quicker than the car managed in any other session and than anyone else in its class all week; usually a swapped transponder): Tom Burt in Cal Club 2025 PM (1:42.300; the car's best in any other session was 1:52.334 and the rest of the class's best all week 1:50.233).
5 laps are left out as timing errors (far too short to be a lap of this track). The rest of those sessions, sectors included, is used.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Formula Enterprise
FE2
1
1:12.402Blake Pigeon
1:12.402Blake Pigeon
SCCA Ent SRF3
FE2/SRF3
42
1:13.988John Yeatman
1:13.988John Yeatman
1:39.712Paul Marino
156.6Paul Marino
27.234Paul Marino
28.582Paul Marino
43.028Jon McClintock
SCCA Ent FE2 (2007)
FE2
1
1:13.988John Yeatman
1:13.988John Yeatman
SCCA Ent FE2 (2010)
FE2
1
1:14.003Thomas W Burt
1:14.003Thomas W Burt
SCCA Ent FE2
FE2
5
1:39.265Jon McClintock
1:39.265Jon McClintock
1:39.712Paul Marino
156.6Paul Marino
27.234Paul Marino
28.582Paul Marino
43.028Jon McClintock
SCCA Ent SRF3
SRF3
38
1:50.233Caleb Shrader
1:50.233Caleb Shrader
1:50.825Caleb Shrader
138.9Paul Marino
30.136Caleb Shrader
31.672Caleb Shrader
44.841Tom Burt
Porsche 986 Boxster
T3
1
1:51.337Reto Eberle
128.4Reto Eberle
29.898Reto Eberle
33.530Reto Eberle
54.812Reto Eberle
Ford Mustang
T3
5
1:55.675Scotty B White
1:55.965Roger Eagleton
1:55.675Scotty B White
137.2Scotty B White
31.598Scotty B White
33.496Scotty B White
50.029Scotty B White
Nissan 370Z
T3
1
1:56.241Gamaliel Aguilar-Gamez
1:56.241Gamaliel Aguilar-Gamez
1:56.899Gamaliel Aguilar-Gamez
131.8Gamaliel Aguilar-Gamez
31.456Gamaliel Aguilar-Gamez
33.615Gamaliel Aguilar-Gamez
50.788Gamaliel Aguilar-Gamez
BMW Z4M
T3
1
1:59.315J. David Orem
2:00.000J. David Orem
1:59.698J. David Orem
128.1J. David Orem
32.480J. David Orem
34.645J. David Orem
51.770J. David Orem
BMW 330ci
T3
1
1:59.844Ron Tanemura
1:59.844Ron Tanemura
1:59.971Ron Tanemura
136.3Ron Tanemura
32.188Ron Tanemura
34.401Ron Tanemura
52.107Ron Tanemura
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
slowerSRF Renault Alliance solid front rotors banned; restrictor reduced 35mm to 34mm for 2011+ Kawasaki; minimum weight increased to 1100 lbs for 2009+ stock engines.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481"). The 1985 Renault Alliance solid front rotor (Reference: Bendix PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type rotor. The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038 may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind;
Show 4 more lines
maximum of one spring per caliper." P2 Engine Table Spec Line Engine Series
A specification table follows in the original; it is not shown here.
wordingT3 Porsche Spec Boxster tire rule updates to current SPB rules or any 245 DOT tire.
As printed in Fastrack
In T3 Spec Lines, Porsche Spec Boxster, change Notes as follows: "Must conform to all SPB rules in the PCA rulebook. Each competitor shall have available definitive current documentation of the PCA rules. Tires must meet 2016 Current SPB rules or any 245 DOT tire permitted. No other touring allowances permitted."
Applies to Porsche 986 Boxster on this page: Reto Eberle
T3 OEM VW Steering Spindle Replacements 06-10 VW GTI and Jetta
wordingSRF3 tail sections allowed on SRFs with GEN3 airbox shimming up to 19 mm; alternate dash panel P/N 180100 or 180101 relocated in rules.
As printed in Fastrack
In Spec Racer Ford, GCR section 9.1.8.D.1.E, change as follows: "j. Optional Bodywork Modification: Viewing the tail section of the car from behind, draw a vertical line at the left and right ends of the outer vents from the bottom edge of the bodywork up to a point two (2) inches below the crease at the lower edge of the vented panel. Make a vertical cut at each line. The horizontal cut is to be one (1) inch below the crease at the base of the vented panel. Leave a one (1) inch radius at each corner. Air Scoop (P/N 190000) must be installed in conjunction with rear cutout per Enterprises installation instructions. SRF3 tail sections are allowed on SRFs. For purposes of tail section to center section fitment with the GEN3 airbox, shimming is allowed at the rear of the center section. Shim material may be up to 19 mm (0.75") thick along the 1" upper square sidepod
Show 11 more lines
tube. Mounting location cannot be modified or added. Shim material must be securely attached, but must not be welded. An alternate dash panel has been approved for use in Spec Racer Fords. The dash will be furnished by Enterprises only. P/N 180100 or 180101 k. Required Bodywork Modification: A 22.5" diameter wheel arch shall be cut in each side of the tail section. Viewing the tail section from the side, draw a vertical line at the drive axle centerline. Locate the top of the wheel arch at a point measured from the bottom edge of the tail section 9.25" vertically along the centerline. The 22.5" diameter circle intersects the bottom edge of the tail section 11.1" either side of the centerline. The tail section may be reinforced in the forward and aft portions of the wheel arch. Dimension tolerance is +/- 0.75". l. An alternate dash panel has been approved for use in Spec Racer Fords. The dash will be furnished by Enterprises only. P/N 180100 or 180101."
T3 Request to all ECS Tuning inner-cooler to 06-10 VW GTI spec
unclearSRF Hoosier wet front tire updated to P/N 46100 P185/60R13 H20 or W2.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."
fasterT3 Camaro V6 1LE and LT-I4 Turbo 1LE max wheel diameter increases from 18 to 20 inches.
As printed in Fastrack
In T3 Spec Lines, Chevrolet Camaro V6 1LE (2016-), change Max. Wheel Size as follows: "18 x 10 20 x 10" In T3 Spec Lines, Chevrolet Camaro LT-I4 Turbo 1LE (2016-), change Max. Wheel Size as follows: "18 x 10 20 x 10"
wordingT3 Mazda RX-8 removes transmission/final drive pairing requirement; T4 removes same requirement, adds Mazdaspeed radiator and coil spring kit.
As printed in Fastrack
In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows: "Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3 transmission must be paired with the listed alternate final drive. Front sway bar permitted 32mm MAX rear sway bar 19 MAX, Front springs max 750, 500 rear. Cold air intake permitted. Header permitted. Aftermarket flywheel and single disc clutch permitted with no weight penalty." In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows: "Mazdaspeed radiator #0000-01-8501 allowed. Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3 transmission must be paired with the listed alternate final drive. Mazdaspeed coil spring kit #QSEA-34-01Z allowed. 60mm flat plate restrictor required. OE Rear spoiler allowed #F151-V4-920F. OE front air dam allowed #F151-V4-900f-BB. Springs Allowed:
Show 2 more lines
(F) Mazda Motorsports- 0000- 04-9700-08 or Eibach- 0800.250.0700 (R) Mazda Motorsports- 0000-04-9400-07 or Eibach 0700.250.0400, and helper 0000-04-9926 allowed. Alternate sway bars allowed max 32mm (f) 19mm (r)."
fasterT3 BMW 320i (14-15) gains aftermarket intercooler permission; T4 loses it.
As printed in Fastrack
In T3 Spec Lines, BMW 320i (14-15), add to Notes the following: "Aftermarket intercooler permitted." In T4 Spec Lines, BMW 320i (14-15), remove from Notes the following: "Aftermarket intercooler permitted."
wordingT3 Pontiac Solstice GXP minimum ride height set to 3 inches.
As printed in Fastrack
In T2 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following: "Minimum ride height is 3 inches." In T3 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following: "Minimum ride height is 3 inches."
wordingSRF radiator rule clarified: P/N 480466 replaceable with Automotive P/N 1R698, CU698 or manufacturer equivalent with documentation.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.V.j, change as follows: "Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent, as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."
T3 2006-10 Volkswagen GTI - Weight Reduction request and KO4 Turbo
fasterT3 Porsche Cayman (09-12) and (13-16) gear and final drive ratios adjusted; 09-12 6-SPD final drive 3.88 to 3.875, PDK 3.909 to 3.250; 13-16 6-SPD final drive 3.89 unchanged, PDK 3.91 to 3.250.
As printed in Fastrack
In T3 Spec Lines, change gear ratios and final drive ratios as follows:
A specification table follows in the original; it is not shown here.
wordingT3 VW Golf GTI and Golf R TIR location clarified to maximum 60mm from impeller.
As printed in Fastrack
In T3 Spec Lines, Volkswagen GTI (2013), change Notes as follows: "Rear sway bar max 42 mm (body and suspension mounting same as OEM), Any spring up to a maximum spring rate of 800 pounds may be used. Turbo Inlet Restrictor 36mm required max 60mm from impeller. R32 model brake package allowed. Verkline WAS-048 camber arms permitted." In T3 Spec Lines, Volkswagen Golf R (15-16) change Notes as follows: "Max spring rate 800 F&R, Max swaybar 38mm F, 42mm R. 36mm TIR required max 60mm from impeller."
wordingSRF rain/brake light now requires Super Bright LEDs Inc. P/N PT-STRB-R24 with specific connector and rain light switch.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain light."
wordingSRF requires Super Bright LEDs P/N PT-STRB-R24 rain/brake light with strobing capability and specific wiring.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."
slowerT3 Nissan 350Z DE motor loses 75 lbs to 3125; HR motor gains 47mm restrictors, up from 44mm.
As printed in Fastrack
In T3 Spec Lines, Nissan 350ZTrack/ Touring/Standard/Nismo(03-08), change as follows: Weight: "DE Motor: 3200 3125 HR Motor: 3275" Notes: "HR Engine: Two 44mm 47 mm flat plate restrictors required. DE engine: Cold air intake permitted."
wordingT3 2010 Mustang GT 4.6 now allows 2013-14 GT style front/rear fascia, hood, and associated assemblies.
As printed in Fastrack
In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), add to Notes the following: "2010 models may update the front and rear fascia, hood and associated assemblies to the 2013-14 GT style."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
fasterT3 BMW SpecE46 minimum weight drops 50 lbs to 2850.
As printed in Fastrack
In T3 Spec Lines, BMW SpecE46, change as follows: Min Weight: "2900 2850" Notes: "Must conform to all SpecE46 rules Version 2.10. SpecE46 spec tire permitted or any DOT permitted up to 225 permitted. No other touring allowances permitted. Engines may not be modified unless specified in the Spec E46 rules and must conform to touring tech procedures. Driver must possess a current copy of the rules. Dyno results do not ensure engine compliance. SE46 HP limit does not apply."
otherSRF adds brake duct and pedal extension rules, rear shift cable clamp option, camber limit to 5.0°, radiator opening height 3.5" ±0.5", and P2 engine restrictor changes.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.H, add the following: "NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part # P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad "anti-rattle" clips must be removed." In SRF, GCR section 9.1.8.D.1.V, add the following:
Show 23 more lines
"ii. Rear SADEV shift cable aluminum two-piece style clamp may be used. The P/N WM302007A clamp must serve no other purpose." In SRF, GCR section 9.1.8.D.1.X.k, add the following: "Negative camber shall must not exceed 5.0 degrees absolute maximum front and rear." In SRF, GCR section 9.1.8.D.1.AA.b, add the following: "2. Height of the radiator opening vertical surface 3 1/2“ +/- 1/2"." P2 Engine Table B.1 2008 and older Stock Suzuki, Yamaha, Honda, BMW 38.5mm P2 Engine Table B.2 Not required P2 Engine Table B.3 38.5mm Modified Engine 950 lbs. 1005cc max P2 Engine Table B.1 2008 and older 37mm P2 Engine Table B.2 Not required P2 Engine Table B.3 39mm Stock Engine 1050 lbs.
slowerT3 Subaru STI (15-20) minimum weight increases 100 lbs to 3450; all three STI variants get larger turbo inlet restrictors.
As printed in Fastrack
In T3 Spec Lines, Subaru WRX STI (03-07), change Notes as follows: "Killer B intake pipe #EJTI and coupler permitted. 37mm 39mm TIR required." In T3 Spec Lines, Subaru STI (15-20), change as follows: Min Weight: "3350 3450" Notes: "Killer B intake pipe #EJTI and coupler permitted. 37mm 40mm TIR required." In T3 Spec Lines, Subaru Legacy GT/Spec B (05-09), change Notes as follows: "Killer B intake pipe #EJTI and coupler permitted. 37mm 39mm Turbo inlet restrictor required."
T3 15-18 Golf R Alignment with Existing GTI and R Speclines
In GCR, Section 9.1.9.2.D.1.g.3., change as follows: "Batteries may be replaced provided the replacement is capable of starting the car. Batteries may not be relocated unless noted on the spec line. Batteries must be adequately secured. Battery labeling must conform to 9.3.35.D. with those of an alternate manufacturer, provided they are of similar amp-hour capacity, size and within 10% of OEM weight."
T3 Open Strut Tower Brace Options for Ford Mustang V6 (11-14)
cars addedT4 now permits C-Spec cars to compete alongside B-Spec cars.
As printed in Fastrack
In GCR, Section 9.1.9.2., change as follows: "Touring car eligibility: Cars are eligible for the class they are listed with a specification line and with the specific allowances permitted. In addition, T2-T4 cars may race one class up in touring classes above their specification line class as long as they are a legal T2-T4 car and conform to their specification line allowances as classified. Cars conforming to C-Spec rules are permitted to compete in Touring 4."
wordingT2-T4 spec lines for 46 cars expire 12/31/24; appeal required to continue.
As printed in Fastrack
In T2-T4 Spec Lines, add **This Spec line will expire 12/31/24, Please submit to appeal** to Notes to the following Spec Lines: T2: Acura TL SHAWD (10-13) Audi S4 (12-14) Audi S5 (13-14) Audi TT RS (2018-) Cadillac ATS-V (16-17)
Show 46 more lines
Cadillac CTS-V (06-07) Chevrolet Camaro SS (98-02) Honda Civic (2017-) Saturn Sky / Convertible (07-09) Subaru Impreza WRX STi (03-07) Subaru Impreza WRX STi (08-11) T3: Audi S4 (10-11) Audi S4 (12-14) Audi TTS Coupe (10-11) Cadillac ATS (2015) Chevrolet Cobalt (05-07) Dodge SRT-4 (03-05) Ford Fiesta ST (2014-) Hyundai Genesis Coupe (2010-) Hyundai Veloster Turbo (18-21) Mazda RX-8 Base/R3/Sport/ GT (04-12) Mini Cooper S (2016-) Subaru WRX (02-05) Toyota Camry (11-15) T4: Acura Integra GS-R VTEC (3 or 4 door) (94-01) Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05) BMW 320i (14-15) Chevrolet Cobalt SS, Sport Coupe (06-10) Chevrolet Sonic RS (2011-) Chrysler/Dodge Neon ACR SOHC (4 door) (01-02) Dodge Dart (14-15) Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99) Fiat 500 Abarth (12-14) Ford Focus SVT (02-04) Ford Focus ZX4 ST (05-06) Ford Focus (08-11) Ford Mustang V-6 (01-04) Honda Accord LX & EX (03-07) Honda Accord LX-S/EX/EX-L (08-12) Honda Civic Coupe Si (99-00) Honda Civic SI (02-03) Hyundai Elantra GLS (11-12) Hyundai Tiburon V-6 (03-08) Hyundai Veloster Turbo/ R-Spec (14-15) Kia Forte Koup and Sedan LX/EX (10-13) Kia Forte Koup and Sedan SX (10-13) Kia Forte Koup (14-15) Mazda Protégé ES (2000) Mazda Protégé 5 (02-03)
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
fasterT3 Spec Z 350Z rear wheel width increases to 10 inches; HR Engine restrictors change from 42mm to 44mm.
As printed in Fastrack
In T3 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo Spec Z (03-08), change as follows: Max Wheel Size (inch): "18 x 9 (F) 18 x 10 (R)" Notes: "Nissan Motorsports: Shock Front left P/N E6110-SZ350 & Front right E6111- SZ350 & rear E6210-SZ350, springs front P/N 54010-SZ350 & rear 55020- SZ350, F&R 5600S-SZ350, Front sway bar max 37mm. Rear sway bar max 25mm, Bushings P/N (54541, 54560, 55045, 55148, 55149, 55152, 55153, 55158, 56218) - RRZ30 allowed. Nismo flywheel permitted. SPC Control Arms 72125 and 72123 are allowed. HR Engine: Two 42mm flat plate restrictors required. Zspeed and Z1 alternative clutch slave permitted. Must conform to all SpecZ 2018 Edition rules. No other touring allowances beyond 2018 SpecZ edition rules or allowances listed here. Nissan brake part numbers NISMO Race Front Caliper Kit 41001-FR350, NISMO Front Rotor-RIGHT 40206-
Show 3 more lines
SZ350, NISMO Front Rotor-LEFT 40207-SZ350 permitted. 44011-RC350 rear caliper kit permitted, 43206-SZ350 Right rotor permitted, 43207-SZ350 Left rotor permitted. Car must conform to the Official 2024 Spec Z Rules. HR Engine: Two 44mm flat plate restrictors required. Tires must conform to Spec Z rules. Competitor must be able to provide a copy of the current rules."
suspension & brakesT3 Nissan 350Z and 370Z now allow brake booster vacuum regulator, must not be in-car adjustable.
As printed in Fastrack
In T3 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo (03-08), add to Notes as follows: "Brake booster vacuum regulator allowed, cannot be in-car adjustable." In T3 Spec Lines, Nissan 370Z, incl. Nismo (2009-2022), add to Notes the following: "Brake booster vacuum regulator allowed, cannot be in-car adjustable."
Applies to Nissan 370Z on this page: Gamaliel Aguilar-Gamez
fasterT3 Ford Mustang 4.6L restrictor holes increased from 40 mm to 45 mm.
As printed in Fastrack
In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), change Notes as follows: "A flat plate restrictor with two 40 mm 45mm holes required directly behind throttle body."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 Appeal for Retention of T3 Mazda RX-8 Spec Line (Letter #35378)
unclearT3 and T4 Mazda RX-8 may remove or disable factory oil injection system.
As printed in Fastrack
In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows: "OEM oil injection system may be removed or disabled." In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows: "OEM oil injection system may be removed or disabled."
slowerT2, T3, T4 driveshafts may use alternative materials or one-piece units; non-OEM adds 25 lbs.
As printed in Fastrack
In GCR Section 9.1.9.2.D.4.b., add the following: "6. T2-T3- Driveshafts may be replaced with alternative materials ie. carbon fiber, aluminum, steel. Two-piece driveshafts may be replaced with one-piece units. If non-OEM driveshaft is used, add 25 lbs."
wordingAudi S4 00-02 in T3 must compete in 3 Super Tour events before Runoffs eligibility.
As printed in Fastrack
In T3 Spec Lines, Audi S4 (00-02), add to Notes as follows: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
unclearFord Mustang GT 5.0L and V6 now permit Track/Performance Package parts in T2 and T3.
As printed in Fastrack
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes as follows: "Track/Performance Package parts permitted." In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows: "Track/Performance Package parts permitted." In T3 Spec Lines, Ford Mustang V6 (15-17), change Notes as follows: "Track/Performance package allowed."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
fasterT2-T4 Ford Mustangs: remove 25 lbs penalty for non-OEM driveshaft, clarify alternate driveshaft allowances.
As printed in Fastrack
In GCR Section 9.1.9.2.D.4.b.6., remove as follows: "If non-OEM driveshaft is used, add 25 lbs." In T2 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows: "Driveshaft from Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang Boss 302 (12-13), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang GT 5.0L (11-14)ki, change Notes as follows: "Alternate metallic driveshaft is allowed."
Show 12 more lines
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L (05-10), change Notes as follows: 'An Aluminum driveshaft is allowed." "Alternate metallic driveshaft is allowed." In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), change Notes as follows: "An Aluminum driveshaft is allowed." "Alternate metallic driveshaft is allowed." In T3 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows: "Driveshaft from Alternate metallic driveshaft is allowed."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
cars addedT3 BMW Z4 3.0si expands to include 3.0i Roadster and Coupe (07-08); hardtop permitted with positive fasteners.
As printed in Fastrack
In T3 Spec Lines, BMW Z4 3.0si, & Coupe (07-08) change Model and add to Notes as follows: "BMW Z4 3.0si, 3.0i, Roadster & Coupe (07-08)" Notes: "Any OEM or aftermarket hardtop permitted that retains the OEM roof silhouette (if a hardtop is used, latches shall be replaced with positive fasteners)."
fasterT3 Honda Civic Si (2017-2021) restrictor removed, weight to 2950 lbs, Runoffs eligibility requires 3 Super Tour events.
As printed in Fastrack
In T3 Spec Lines, Honda Civic Si (2017-) with 2900 weight, change as follows: Model: "Honda Civic Si (2017-2021)" Restrictor: "36mm TIR" Add to Notes: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**" In T3 Spec Lines, Honda Civic Si (2017-), change as follows: Model: "Honda Civic Si (2017-2021)" Restrictor: "36mm TIR" Weight (lbs): "30752950"
Show 1 more lines
Add to Notes: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
wordingT3 Subaru STI (15-20) and WRX STI (03-07) permitted to use OEM spec block #IAG-ENG-S550 and head studs.
As printed in Fastrack
In T3 Spec Lines, Subaru STI (15-20), add to Notes the following: "OEM spec block permitted # IAG-ENG-S550, Head studs permitted." In T3 Spec Lines, Subaru WRX STI (03-07), add to Notes the following: "OEM spec block permitted # IAG-ENG-S550, Head studs permitted."
slowerSRF wet tires: P185/60R13 H20/W2 option removed; P185/65R13 W2 front now required with P205/60R13 W2 rear.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used. OR Front – Hoosier P/N 46101 P185/65R13 W2 Rear – Hoosier P/N 46105 P205/60R13 W2
Show 8 more lines
1. It is forbidden to regroove tires. 2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for violation will be the loss of qualifying times and/or the disqualification of race results. 3. Hoosier SRF/SRF3 Decal Placement: Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises."
SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info
wordingSRF Hoosier decal requirement reduced from four decals in specific locations to three decals with simpler placement rules.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows: "Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
slowerSRF brake rotor minimum thickness increases from 12.20mm to 13.25mm, Wilwood vented rotor P/N 800065.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."
wordingSRF3 Hoosier logo placement changes from four decals to three decals in different locations.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.2.B, change as follows: "Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."
wordingT3 VW Golf R (12-13 and 15-18) 36mm TIR placement now allows OEM turbo inlet, removing 60mm distance limit from impeller.
As printed in Fastrack
In T3 Spec Lines, Volkswagen Golf R (12-13), change Restrictor Required as follows: "36mm TIR max 60mm from impeller TIR may be placed in the OEM turbo inlet as long as the restriction is entirely within the leading edge of the housing." In T3 Spec Lines, Volkswagen Golf R (15-18), change Restrictor Required as follows: "36mm TIR max 60mm from impeller TIR may be placed in the OEM turbo inlet as long as the restriction is entirely within the leading edge of the housing."
T3 Redundant Verbiage Regarding Mustang Spec Lines for Driveshaft
wordingT2 and T3 Mustang spec lines remove redundant driveshaft alternate/aluminum allowance wording.
As printed in Fastrack
In T2 Spec Lines, change Notes as follows: Ford Mustang V6 (11-14): "Alternate driveshaft is allowed." Ford Mustang Boss 302 (12-13): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (11-14): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (15-17): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (2018-): "Alternate driveshaft is allowed. Springs up to 800#/in front and rear permitted. Alternate metallic driveshaft permitted." Ford Mustang Coupe GT & Shelby GT 4.6L (05-10): "Alternate driveshaft is allowed."
Show 4 more lines
In T3 Spec Lines, change Notes as follows: Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10): "Alternate driveshaft is allowed." Ford Mustang V6 (11-14): "Alternate driveshaft is allowed." Ford Mustang V6 (05-10): "An Aluminum driveshaft is allowed."
wordingT2, T3, T4 fuel cell installations may remove charcoal canisters, emissions valves, and sensors.
As printed in Fastrack
In GCR, Section 9.1.9.2.D.1.c. add the following: "5. Removal of ancillary fuel tank equipment charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket fuel cell installations."
wordingT2, T3, T4 brake component wording clarified: 2-piece rotors allowed in T2 within 5% OE diameter, T3 within 2% OEM diameter.
As printed in Fastrack
In GCR, Section, 9.1.9.2.D.6. Brakes, change as follows: "a. Components 1. The make and material of brake pads and linings may be changed. 2. Brake fluid may be substituted with any brake fluid. 3. Brake rotor dust shields may be removed or replaced to accommodate brake ducts. 4. Flexible rubber brake lines may be replaced with Teflon lined, metal braided hoses. 5. Any brake ducts are permitted, but they must serve no other purpose. Fender liners may be modified solely for routing and attachment of brake ducts. Duct intake openings may be created by the opening of 2 sections up to 14.5 square inches each in
Show 10 more lines
the front fascia. The stock headlamp location is not permitted for brake ducting. Two alternative duct openings may be created by the removal of the fog lights or 2 sections up to 14.5 square inches each of stock false grills originally located in the front fascia. 6. Stock replacement brake rotors may be obtained from sources other than the manufacturer provided they are the exact equivalent of the stock rotors. In T2 only - 2-piece rotors with ferrous metal rotor disks and aluminum hats are allowed, must be within 5% of OE diameter. In T3 only - 2-piece front rotors with ferrous metal rotor disks and aluminum hats are allowed, must be within 2% of OEM diameter. Drilled and slotted rotors are permitted. 7. Parking brakes, mechanisms, and actuating components may be removed. 8. Brake vacuum reservoirs sized 0.50 gallons or smaller are permitted. The port or fitting at the vacuum source may not be modified, enlarged or relocated. The vacuum reservoir and brake booster must be a closed system."
wordingT2, T3, T4 fuel cell cars may remove charcoal canisters, emissions valves, and sensors.
As printed in Fastrack
In GCR, Section, 9.1.9.2.D.1.c., add the following: "5. Removal of ancillary fuel tank equipment; charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket fuel cell installations."
T3 Allow Spec MX5 upgrade kit for 2009-11 RX8 S2 Transmision
wordingT3 and T4 Mazda RX-8 and MX-5 permit transmission kit #0000-02-5700.
As printed in Fastrack
In T4 Spec Lines, add the following to Notes: Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted. Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted." In T3 Spec Lines, add the following to Notes: Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted." Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted."
wordingT4 BMW 320i 14-15 Spec Line expires 12/31/24 removed; Turner Motorsports intercooler #024703TMS02 allowed.
As printed in Fastrack
In T4 Spec Lines, BMW 320i (14-15), change Notes as follows: "**This Spec line will expire 12/31/24, Please submit to appeal** Turner Motorsports intercooler #024703TMS02 allowed."
T3 Classification for a 2005 Cadillac CTS 3.6 liter 6 speed manual
fasterT3 Subaru WRX STI 03-07 drops 100 lbs to 3200; Legacy GT/Spec B 05-09 drops 150 lbs to 3200.
As printed in Fastrack
In T3 Spec Lines, Subaru WRX STI (03-07), change Weight as follows: "3300 3200" In T3 Spec Lines, Subaru Legacy GT/Spec B (05-09), change Weight as follows: "3350 3200"
T3 Request to Move Spec Mustang to Touring 3 (from T2)
fasterT3 Ford Mustang V6 (11-14) and (15-17) now permit cold air intake.
As printed in Fastrack
In T3 Spec Lines, Ford Mustang V6 (11-14), add to Notes the following: "Cold air intake permitted." In T3 Spec Lines, Ford Mustang V6 (15-17), add to Notes the following: "Cold air intake permitted."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
In T2, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Acura TL SHAWD (10-13) Audi S4 (12-14) Audi S5 (13-14) Audi TT RS (2018-) Cadillac ATS-V (16-17) Cadillac CTS-V (06-07) Chevrolet Camaro SS (98-02)
Show 49 more lines
Honda Civic Type-R (2017-) Saturn Sky / Convertible (07-09)" In T3, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Audi TTS Coupe (10-11) Cadillac ATS (2015) Chevrolet Cobalt (05-07) Dodge SRT-4 (03-05) Ford Fiesta ST (2014-) Hyundai Genesis Coupe (2010-) Hyundai Veloster Turbo (18-21) Mini Cooper S (2016-) Toyota Camry (11-15)" In T4, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Acura Integra GS-R VTEC (3 or 4 door) (94-01) Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05) Chevrolet Cobalt SS, Sport Coupe (06-10) Chevrolet Sonic RS (2011-) Chrysler/Dodge Neon ACR SOHC (4 door) (01-02) Dodge Dart (14-15) Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99) Fiat 500 Abarth (12-14) Ford Focus SVT (02.5-04) Ford Focus ZX4 ST (05-06) Ford Focus (08-11) Ford Mustang V-6 (01-04) Honda Accord LX & EX (03-07) Honda Accord LX-S/EX/EX-L (08-12) Honda Civic Coupe Si (99-00) Honda Civic SI (02-03) Hyundai Elantra GLS (11-12) Hyundai Tiburon V-6 (03-08) Hyundai Veloster Turbo/ R-Spec (14-15) Kia Forte Koup and Sedan LX/EX (10-13) Kia Forte Koup and Sedan SX (10-13 Kia Forte Koup (14-15) Mazda Protégé ES (2000) Mazda Protégé 5 (02-03) Mazda6 s (03-07) Mitsubishi Eclipse GT (00-05) Nissan Sentra SER (02-03) Pontiac Firebird V-6 (96-02) Scion tC (03-07) Subaru Impreza (non-turbo) (04-06) Toyota Celica GT (00-05) Toyota Celica GTS/GT (00-05) Volkswagen Golf TDI (2010) Volkswagen Passat (12-14) Volkswgen Passat TDI (12-14) Volkswgen Passat 1.8T (2014-)"
wordingFE2 allows driver safety and comfort modifications for disabled drivers with SCCA approval, not transferable to other drivers.
As printed in Fastrack
In FE2, GCR section 9.1.1.G.2.E, add the following: "g. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
wordingSRF drivers with disabilities may modify seat and controls for safety and comfort with approval and logbook notation.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.D, add the following: "f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
unclearT3 BMW Spec E46 rules updated to Version 3.0 from Version 1.1.
As printed in Fastrack
In T3 Spec Lines, BMW Spec E46, change Notes as follows: "Must conform to all SpecE46 rules Version 2.10. Version 1.1 dated Jan. 6, 2025. Version 3.0."
unclearBMW Spec E46 in T3 updates to SpecE46 rules Version 3.0.
As printed in Fastrack
In T3 Spec Lines, BMW Spec E46, change Notes as follows: "Must conform to all SpecE46 rules Version 2.10. Version 1.1 dated Jan. 6, 2025. Version 3.0."
Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following: "SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual." Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038
Show 11 more lines
may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind; maximum of one spring per caliper. 1. Hawk Blue pads P/N 801993 only 2. Wilwood Vented Rotor P/N 800065 only, as delivered, with no machining of any kind. Minimum thickness 13.25mm (0.522") 3. Wilwood universal caliper Kit P/N 1180008 as delivered, caliper only P/N 800038; Wilwood knock back spring P/N 800045 may be used as delivered, with no machining of any kind, and only one spring per caliper 4. Renault caliper rubber bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185A 5. Renault caliper piston may be replaced with P/N 1196184 vented piston as delivered, with no machining of any kind 6. Girling .750" Master Cylinder P/N 880358 as delivered, with no machining of any kind 7. Wilwood .750" Master Cylinder P/N 880357 as delivered, with no machining of any kind 8. Tilton .750" Master Cylinder P/N 880360 as delivered, with no machining of any kind"
otherSRF3 adds HD Oil Cooler P/N G1148500 as alternative to standard cooler P/N G480503.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.V.ff, change as follows: "SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
wordingT3 and T4 Mazda MX-5 Miata models add approved gear kit PT#-0000-02-6100 to notes.
As printed in Fastrack
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T3 Spec Lines, Mazda MX-5 Miata (16-18), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, add to Notes the following: "Gear kit Kit PT#- 0000-02-6100."
wordingT4 Mazda MX-5 Miata/Club/RF (19-24) and (16-18) remove discontinued hardtop part #0000-07-5901; T3 MX-5 Miata (16-18) and Global Cup ND (16-21) same.
As printed in Fastrack
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must remain stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5804-01). Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs #0000-04-9700-08, springs up to 500lb front and 300lb rear allowed. Mazda tower brace 0000-04-5626 allowed. Mazda header
Show 20 more lines
0000-06-5410 allowed." In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. Up to 500lb front and 300lb rear springs allowed. Mazda Motorsports Header part #0000-06-5410 allowed. Mazda tower brace 0000-04-5626 allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5." In T3 Spec Lines, Mazda MX-5 Miata (16-18), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Header permitted. Cold air intake permitted. Front strut brace permitted. Front and rear sway bars permitted up to 35mm, Springs 800 front and 800 Rear max permitted. Any OEM or aftermarket hardtop permitted that retains the OEM roof silhouette including Mazda hardtop part #0000-07-5902- ND and part #0000-07-5901 (discontinued DG Motorsports top). If a hardtop is used, latches shall be replaced with positive fasteners. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, change Notes as follows: "Shoulder harness installation must conform to FIA mounting specifications that are approved for this vehicle per section 6.2 FIA article 253, safety equipment. Must meet all ND2 MX-5 Global Cup rules. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop Mazda hardtop part #0000-07-5902-ND and #0000-07-5902-ND part #0000- 07-5901 (discontinued DG Motorsports). If a hardtop is used, latches shall be replaced with positive fasteners. OBD2 requirement does not apply. Ballast box may be removed. ND2s with sequential gearbox allowed +100 lbs.
unclearT3 Ford Mustang EcoBoost loses optional 2-piece 355mm Brembo rotor brake kit option with 50 lb penalty.
As printed in Fastrack
In T3 Spec Lines, Ford Mustang EcoBoost (2015-), change Notes as follows: ", or optional 2-piece rotor 355mm max Brembo brake kit #M-2300-S allowed with +50lb penalty."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 Request to Allow Spec Mustang to Touring 3 in Appendix M Trim
fasterT3 BMW Spec E9X tire width increases to 255 from 225; spec E9X tire or any DOT permitted.
As printed in Fastrack
In T3 Spec lines, BMW Spec 9X, change as follows: Car: "BMW Spec 9X BMW Spec E9X" Notes: "Must conform to all SpecE9X rules Version 2.10. Spec E9X spec tire permitted or any DOT permitted up to 225 255 permitted. No other touring allowances permitted. Engines may not be modified unless specified in the Spec E46 rules and must conform to touring tech procedures. Driver must possess a current copy of the rules. Dyno results do not ensure engine compliance. THIS SPEC LINE DOES NOT QUALIFY FOR SCCA RUNOFFS COMPETITION UNTIL IT HAS BEEN REPRESENTED IN 3 SCCA SUPER TOUR EVENTS."
fasterT3 SpecE46 permitted tire width increases from 225 to 245.
As printed in Fastrack
In T3 Spec Lines, BMW SpecE46, change Notes as follows: "Must conform to all SpecE46 rules Version 3.0. SpecE46 spec tire permitted or any DOT permitted up to 225 245 permitted. No other touring allowances permitted. Engines may not be modified unless specified in the Spec E46 rules and must conform to touring tech procedures. Driver must possess a current copy of the rules. Dyno results do not ensure engine compliance. SE46 HP limit does not apply."
T3 Alternate Placement of Fuse Panel and Electronics Request
wordingT2, T3, T4 cars may relocate under-dash electronics and fuse boxes for access after roll cage installation.
As printed in Fastrack
In GCR, Section 9.1.9.2.D.9.d, add the following: "8. Under-dash electronics including computers, modules and fuse boxes may be relocated so they can be easily accessed after roll cage installation."
suspension & brakesT4 Performance now permits 1-piece alternative rotors matching spec line sizes; alternate brake kits allowed same.
As printed in Fastrack
In GCR, Section 9.1.9.2.D.6.a.6., change as follows: "In T2-Performance alternative rotors, including 2 piece rotors are permitted. Rotors must be within 5% of OE diameter or a maximum diameter of 360mm. In T3- Performance alternative rotors, including 2 piece rotors are permitted with a maximum diameter of 360mm. T4- Performance alternative 1-piece rotors are permitted but rotors must meet the sizes listed in the spec line. Spec lines showing alternate brake kits are also permitted to use 1-piece performance alternative rotors of the same size."
T3 Please change 2011-2014 Mustang V6 Spec Line to 2005-2014
fasterT2-T4 adjustable toe links now allow performance alternative bushings and spherical bearings, previously prohibited except in specified examples.
As printed in Fastrack
In GCR, Section 9.1.9.D.5.a.1., change as follows: "T2-T4: A maximum of 3.5 degrees of negative camber is allowed on front and rear suspensions. Spec line part(s) may not be modified to increase caster and camber. Strut suspensions may adjust camber and caster by the use of eccentric bushings, eccentric bolts (crash bolts) at the strut-to-spindle, and/or by use of slotted adjustment plates at the top of the strut mounting plate. If upper strut slotted adjustment plates are used, they shall be located on existing chassis structure, utilizing the unmodified manufacturer’s original bolt holes and may not serve as reinforcement for that structure. Slotted adjustment plates (strut camber plates) may incorporate a single spherical bearing (spherical bushing) and a ball thrust bearing per strut tower. On other forms of suspension, camber and caster adjustment may be achieved by the use of shims and/or eccentric
Show 4 more lines
bushings. Adjustable toe links with spherical bearings are permitted and may serve no purpose other than adjusting toe angle. Adjustable toe links are permitted. They are allowed to have performance alternative bushings and spherical bearings. They may serve no purpose other than adjusting toe angle. Spherical bearings/bushings are not permitted in T2-T4 except for the specific examples listed in the class rules or vehicle spec line."
What the rules allowed changed as listed; this does not say what any particular car ran.