This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One run is left out as not that car's own laps (far quicker than the car managed in any other session and than anyone else in its class all week; usually a swapped transponder): Tom Burt in Cal Club 2025 PM (1:42.300; the car's best in any other session was 1:52.334 and the rest of the class's best all week 1:50.233).
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Chevrolet Camaro
GT2
3
1:42.698Tim Carroll
1:42.698Tim Carroll
1:44.128Tim Carroll
149.2Jean Meynet
28.543Jean Meynet
29.839Tim Carroll
44.262Tim Carroll
Ford Mustang
GT2
1
1:45.818Brad McAllister
1:45.818Brad McAllister
1:46.926Brad McAllister
115.9Brad McAllister
28.729Brad McAllister
30.833Brad McAllister
45.847Brad McAllister
Dodge Challenger
GT2
1
1:46.922Ben Valentine
1:46.922Ben Valentine
1:47.171Ben Valentine
132.9Ben Valentine
29.689Ben Valentine
30.929Ben Valentine
45.990Ben Valentine
Porsche GT3
GT2
2
1:47.914Rocky Crocker
1:47.914Rocky Crocker
1:48.433Rocky Crocker
155.7Rocky Crocker
29.826Rocky Crocker
31.456Rocky Crocker
46.030Rocky Crocker
Porsche GT3
GT2
1
1:47.914Rocky Crocker
1:47.914Rocky Crocker
1:48.433Rocky Crocker
155.7Rocky Crocker
29.826Rocky Crocker
31.456Rocky Crocker
46.030Rocky Crocker
Porsche GT3 Cup
GT2
1
1:57.745Robert Kelley
1:57.745Robert Kelley
1:58.760Robert Kelley
125.1Robert Kelley
32.864Robert Kelley
33.998Robert Kelley
50.578Robert Kelley
Chevrolet Corvette
GT2
1
1:49.904Igor Lyustin
1:50.345Igor Lyustin
1:49.904Igor Lyustin
145.8Igor Lyustin
30.271Igor Lyustin
31.850Igor Lyustin
47.568Igor Lyustin
SCCA Ent SRF3
SRF3
38
1:50.233Caleb Shrader
1:50.233Caleb Shrader
1:50.825Caleb Shrader
138.9Paul Marino
30.136Caleb Shrader
31.672Caleb Shrader
44.841Tom Burt
Mazda RX-7
EP/GT2
5
1:51.013Guy Laidig
1:51.013Guy Laidig
1:52.486Guy Laidig
138.7Guy Laidig
30.134Guy Laidig
32.225Guy Laidig
47.907Guy Laidig
Mazda Miata
EP
1
1:52.034Joe Carr
1:59.603Joe Carr
1:59.157Joe Carr
131.6Joe Carr
31.719Joe Carr
32.405Joe Carr
49.966Joe Carr
Mazda MX-5
EP
2
1:53.088Glen McCready
1:53.088Glen McCready
1:53.487Glen McCready
125.6Glen McCready
30.761Glen McCready
32.765Glen McCready
49.458Glen McCready
Dodge VIPER
GT2
1
1:57.753Robert Kelley
2:00.453Robert Kelley
1:59.538Robert Kelley
92.9Robert Kelley
31.983Robert Kelley
33.965Robert Kelley
51.553Robert Kelley
BMW E30
EP
1
2:00.712Sean Lovett
2:00.712Sean Lovett
2:01.864Sean Lovett
127.6Sean Lovett
32.761Sean Lovett
34.806Sean Lovett
53.058Sean Lovett
Porsche Boxster
EP
1
2:01.940William Robinson
2:01.940William Robinson
2:02.887William Robinson
130.6William Robinson
32.969William Robinson
35.257William Robinson
53.408William Robinson
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
slowerSRF Renault Alliance solid front rotors banned; restrictor reduced 35mm to 34mm for 2011+ Kawasaki; minimum weight increased to 1100 lbs for 2009+ stock engines.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481"). The 1985 Renault Alliance solid front rotor (Reference: Bendix PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type rotor. The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038 may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind;
Show 4 more lines
maximum of one spring per caliper." P2 Engine Table Spec Line Engine Series
A specification table follows in the original; it is not shown here.
wordingSRF3 tail sections allowed on SRFs with GEN3 airbox shimming up to 19 mm; alternate dash panel P/N 180100 or 180101 relocated in rules.
As printed in Fastrack
In Spec Racer Ford, GCR section 9.1.8.D.1.E, change as follows: "j. Optional Bodywork Modification: Viewing the tail section of the car from behind, draw a vertical line at the left and right ends of the outer vents from the bottom edge of the bodywork up to a point two (2) inches below the crease at the lower edge of the vented panel. Make a vertical cut at each line. The horizontal cut is to be one (1) inch below the crease at the base of the vented panel. Leave a one (1) inch radius at each corner. Air Scoop (P/N 190000) must be installed in conjunction with rear cutout per Enterprises installation instructions. SRF3 tail sections are allowed on SRFs. For purposes of tail section to center section fitment with the GEN3 airbox, shimming is allowed at the rear of the center section. Shim material may be up to 19 mm (0.75") thick along the 1" upper square sidepod
Show 11 more lines
tube. Mounting location cannot be modified or added. Shim material must be securely attached, but must not be welded. An alternate dash panel has been approved for use in Spec Racer Fords. The dash will be furnished by Enterprises only. P/N 180100 or 180101 k. Required Bodywork Modification: A 22.5" diameter wheel arch shall be cut in each side of the tail section. Viewing the tail section from the side, draw a vertical line at the drive axle centerline. Locate the top of the wheel arch at a point measured from the bottom edge of the tail section 9.25" vertically along the centerline. The 22.5" diameter circle intersects the bottom edge of the tail section 11.1" either side of the centerline. The tail section may be reinforced in the forward and aft portions of the wheel arch. Dimension tolerance is +/- 0.75". l. An alternate dash panel has been approved for use in Spec Racer Fords. The dash will be furnished by Enterprises only. P/N 180100 or 180101."
slowerEP BMW Z3 2.5L intake restrictor reduced from 58mm to 56mm flat plate.
As printed in Fastrack
Effective 4/1/2023 In EP Spec Line BMW Z3 2.5L, change Notes as follows: "58 56mm Flat Plate Intake Restrictor is required with both stock or alternate throttle body."
GT2 Adding Ginetta G56 GTA Factory ProTune for GT2 Class
cars added2009-2012 Porsche Cayman S classified in GT2, 3.4L, RWD, no PDK transmission allowed.
As printed in Fastrack
In GT Cars - Porsche, classify Porsche Cayman ‘S’ as follows: GT Cars - Porsche Model Years Body Style Drive- line Wheel- base (in) Notes Porsche Cayman ‘S’ 09-12 2 dr. Coupe RWD 95.08 3.4L No PDK Transmission
cars addedFields Cardinal V8 classified in GT1 with Ford V8 engine, 4.9L displacement, 2100 lbs minimum weight.
As printed in Fastrack
In GT Spec Lines, GT1 Cars - Fields Cardinal, classify Fields Cardinal V8 as follows: GT1 Cars – Fields Cardinal Model Years Body Style Drive- line Wheel- base (in) Notes Fields Cardinal V8 2023 2 Dr. RWD 92.0 Roll Cage MUST be modified to comply with
Show 6 more lines
GCR Section 9.4. In GT Spec Lines, GT1Engines - classify Ford V8 as follows: GT1 Engines - Ford Engine Family Engine Type Bore x
A specification table follows in the original; it is not shown here.
unclearSRF Hoosier wet front tire updated to P/N 46100 P185/60R13 H20 or W2.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."
wordingGT2 BMW engines: 3.4L 6-cyl at 2575 lbs, 4.0L V8 at 2900 lbs, 4.5L V8 at 2950 lbs, 5.0L V8 at 3000 lbs; S54 with 97mm stroke permitted at 2800 lbs.
As printed in Fastrack
In GT2-ST Spec Lines, BMW E46 M3 & E36 / BMW Z3 / BMW 5000cc V8, change notes as follows: "The 3.4 liter 6 cyl. (87.0 bore x 93.0 stroke) is permitted at 2575lbs. 4.0L V8 permitted at 2900lbs. 4.5L V8 permitted at 2950lbs. 5.0L V8 permitted at 3000lbs. Flossman body kit permitted as found at http://www.racingpartsbmw.de/start/eng/start.htm. Trans Am SGT spec: Regular shifter 3000 lbs., paddle shifter plus 150 lbs. 95mm S54 crankshaft @ +150lbs. Lang Racing part# S54-95mm-StrokerCrk. S54 engine is permitted a 97mm stroke crankshaft (part #VAC-SC-S54) @2800lbs."
GT2 Remove Weight and Restrictor Penalty for Corvette C7 Body
wordingFP and HP Sprite, Midget, and Spitfire 1500 intake valve size corrected to 36.6/(1.44).
As printed in Fastrack
In FP Spec Lines, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change Intake Valve Size as follows: "(I) 36.65.3/(1.44)" In FP Spec Lines, Triumph Spitfire Mk. IV & 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire Mk. III & IV 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)"
wordingEP Triumph TR8 78-81 removes alternate front hub allowance note; stock hubs now required.
As printed in Fastrack
In the EP Spec Lines, Triumph TR8 (78-81), remove the following wording from Notes: "Alternate front hubs are allowed provided they are of the same external dimensions as stock and weigh no less than the stock hubs."
fasterGT2 Mazda 20B 3 rotor loses 220 lbs, to 2280, consolidating two spec lines.
As printed in Fastrack
In GT2 Spec Lines, Engines - MAZDA, combine both 20B to one spec lines and keep the following: Weight: "2500 2280" Notes: "Must run +100 lbs. for Grand Am transaxle and independent rear suspension. Must comply with all other GT2 rules."
wordingSRF radiator rule clarified: P/N 480466 replaceable with Automotive P/N 1R698, CU698 or manufacturer equivalent with documentation.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.V.j, change as follows: "Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent, as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."
fasterGT2-ST Dodge Viper including Comp Coupe, ACR/ACR-X with VRL front fascia loses 100 lbs.
As printed in Fastrack
RM 23-10 GT2-ST Dodge Viper, incl Comp Coupe, ACR/ACR-X VRL Front Fascia As an Errors and omissions fix to what was originally intended for these cars, the Club Racing Board and Board of Directors have approved the following: In GT2-ST, Dodge Viper, incl Comp Coupe, ACR/ACR-X add VRL front fascia -100lbs to all Spec Lines.
GT2 Errors in GTCS Headings and Use of the Terms Category and ClassChange existing GTL and GTA Rules
wordingGTL spec lines moved to contiguous position with GT2 and GT3; GTA category and spec lines renumbered and moved behind GTL.
As printed in Fastrack
from the current (or before) Table of Contents (TOC), to what is shown in the after TOC. GTL spec lines will now be contiguous with GT2 and 3 spec lines. GTA category and spec lines will be moved and renumbered behind GTL. GTA Section will not change but page numbers will, (as shown in Red italics). 9.1.2.F. GT-2, 3, LITE Category Specifications 314 GT2 Cars 327 GT2/ST 341 GT3 Cars 348
cars addedEP Porsche 944/924S combines 2.5L and 2.7L variants with new weights: 2250–2415 lbs depending on engine and year.
As printed in Fastrack
In EP Spec Lines, delete the Porsche 944/924S 2.5L (2V) (83-88) spec line entirely, and create a new spec line for Porsche 944/924S 2.5L(2V) 2.7L(2V) (83-89) as follows:
A specification table follows in the original; it is not shown here.
wordingSRF rain/brake light now requires Super Bright LEDs Inc. P/N PT-STRB-R24 with specific connector and rain light switch.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain light."
wordingSRF requires Super Bright LEDs P/N PT-STRB-R24 rain/brake light with strobing capability and specific wiring.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."
slowerGT2-ST Dodge Viper hybrid kit restrictor reduced from 50mm to 45mm flat plates.
As printed in Fastrack
In GT2-ST Spec Lines, Dodge Viper, incl Comp Coupe, ACR/ ACR-X change NOTES as follows: 8300 OEM: "Stock OEM engine. Engine long block, valve train, and intake system must meet stock, shop manual specifications. Hybrid update including Mopar Performance Part #P5156137. May use Mopar part #5038554AF (Gen 5 Intake Manifold manifold allowed with (2) 55mm flat plates) and 8.4L mechanical throttle body allowed. VRL Front Fascia -100lbs." 8300: "Hybrid update including Mopar Performance Part # P5156137, Mopar part #5038554AF manifold and 8.4L mechanical throttle body allowed using (2) 50 45mm flat plate restrictors. VRL Front Fascia –100lbs." 8400: "Intake and Throttle Body from Mopar Performance Part # P5156137allowed using (2) 50 45mm flat plate restrictors. , Mopar part #5038554AF manifold (Gen 5 Intake Manifold allowed with (2) 50mm flat plates) VRL Front Fascia -
Show 1 more lines
100lbs 8400 OEM 3225 Stock OEM engine. Engine long block."
In EP spec line, Triumph GT6, make the following change in the Notes section: "Two (2) 1.75” auto-type carburetors @ 1970 40 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive. Three (3) Weber 40mm DCOE w/28mm venturi on individual runner manifold @ 2020 lb."
otherSRF adds brake duct and pedal extension rules, rear shift cable clamp option, camber limit to 5.0°, radiator opening height 3.5" ±0.5", and P2 engine restrictor changes.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.H, add the following: "NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part # P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad "anti-rattle" clips must be removed." In SRF, GCR section 9.1.8.D.1.V, add the following:
Show 23 more lines
"ii. Rear SADEV shift cable aluminum two-piece style clamp may be used. The P/N WM302007A clamp must serve no other purpose." In SRF, GCR section 9.1.8.D.1.X.k, add the following: "Negative camber shall must not exceed 5.0 degrees absolute maximum front and rear." In SRF, GCR section 9.1.8.D.1.AA.b, add the following: "2. Height of the radiator opening vertical surface 3 1/2“ +/- 1/2"." P2 Engine Table B.1 2008 and older Stock Suzuki, Yamaha, Honda, BMW 38.5mm P2 Engine Table B.2 Not required P2 Engine Table B.3 38.5mm Modified Engine 950 lbs. 1005cc max P2 Engine Table B.1 2008 and older 37mm P2 Engine Table B.2 Not required P2 Engine Table B.3 39mm Stock Engine 1050 lbs.
fasterEP Honda S2000 fuel injected throttle body inside diameter increases from 62mm to 64mm.
As printed in Fastrack
In EP spec line, Honda S2000, make the following changes to its spec line: Fuel Injected Equipped Throttle Body Inside Diameter: "62 64" Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .500”. An adaptor plate can be used to mount the 62mm throttle body from '00-05 to the '06-09 intake manifold. The adaptor plate can be no more than 1.25" thick, and its bore must not exceed the "Fuel Injected Equipped Throttle Body Inside Diameter" maximum spec of 64mm."
wordingEP Triumph TR8 dry sump allowance moved from carburetor line to notes section.
As printed in Fastrack
In EP spec line, Triumph TR8 (78-81), move the "Dry sump allowed" wording to the appropriate location as follows: Carburetor. No. & Type: “Zenith Stromberg carbs or fuel injection. Dry sump is allowed.” Notes: “Comp. Ratio limited to 12.0:1, Valve lift limited to .500”. Dry sump is allowed.”
fasterGT1, GT2, GT3, GTL, GTX rear spoiler maximum surface area limit of 295.0 square inches removed.
As printed in Fastrack
In GCR Section 9.1.2.G (GTA Category Specifications), change as follows: “9.1.2.G.III.I The single-plane rear spoiler must be mounted at an angel angle from 50 to 75 degrees (perpendicular to the ground being 90 degrees) and may not extend beyond the rear bumper when viewed from directly above the rear bumper. Spoilers must be a minimum of .063 aluminum or Lexan and may vary in overall height to match the contours of the bodywork. The rear spoiler dimensions shall not exceed 59.0 inches wide by 5.0 inches in height, (measured on the material surface) , or 295.0 square inches total surface area. Braces to prevent spoiler deflection are allowed, but may serve no other purpose.”
GT2 REDUCE C6 CORVETTE WEIGHT WITH OEM 7 LITER ENGINE REDUCE BY 150LB
fasterGT1/GT2/GT3/GTL/GTX Direct Injection now permitted if OE, using only OE pump, hoses, injectors.
As printed in Fastrack
In GCR, Section 9.1.2.F.7.5.E. change as follows: “Direct Injection is not permitted only if it came OE and must be installed using only OE high pressure pump(s), hard and soft hoses and injectors.”
GT2 GT2/3 remove Direction Injection not allowed in Spec line notes
fasterGT2/3 Nissan, Mazda, Mitsubishi 4G93, QR25DE/DD, QE25DE/DD Direct Injection now permitted per 9.1.2.F.7.5.E.
As printed in Fastrack
In GT2/3 modify Spec Line notes as follows: GT2: Nissan: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” GT3: Mazda: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” Mitsubishi 4G93: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E. ” Nissan QR25DE/DD 1988cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” Nissan QE25DE/DD 2489cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.”
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
cars added2015 Mitjet ST added to GT2, must run per VTS specifications with complete FIA form CdM008.
As printed in Fastrack
In GT2 Spec Lines, GT Cars - MITJET ST, classify MITJET ST as follows: GT Cars – MITJET ST Model Years Body Style Drive- line Wheel- base (in) Notes MITJET ST 2015 RWD 94.5 Must run per VTS specifications. Must have
Show 2 more lines
complete car Specifications (FIA form CdM008) at every entered race event.
In HP Spec Lines, delete the following redundant spec lines in their entirety: Spec line #10 - VW Rabbit Cabriolet 1780 Spec line #3 - VW Scirocco 1588 Spec line #4 - VW Scirocco 1780 (8-valve) (83-88) Spec line #5 - VW Scirocco 1588
wordingEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.
As printed in Fastrack
Spec Lines, make the following changes to the two Mazda RX-8 spec lines. Remove spec line entirely: Mazda RX-8 (04-11) Remove the wording "alternate": Mazda RX-8 (04-11)(alternate) Spec Mazda (SM/SMX) None.
wordingGT2-ST allows aftermarket replacement differential housings if exact equivalents.
As printed in Fastrack
In GCR Section, Appendix K. 2012.M2, add the following: "After market replacement differential housings are permitted as long as they are an exact equivalent."
cars addedGT4 cars now permitted in GT2-ST with factory restrictor, must comply with 2012 STO rules, slicks allowed with 100-pound penalty.
As printed in Fastrack
In 9.1.2. GT2 Spec Lines, GT3 Cars, change Note as follows: "Note: All GT4 cars are permitted to compete in GT2-ST provided they use a factory supplied power stick or Pro Series required restrictor. Must have GT4 rules in possession at all race events. Cars must comply with 2012 STO rules as stated in Appendix K of the GCR. Engine Displacements in this table are nominal. Each competitor shall have available definitive documentation (e.g., factory manual) of the original displacement for the engine used. Slicks allowed on all GT2/ST cars with a 100-pound weight penalty."
slowerSRF wet tires: P185/60R13 H20/W2 option removed; P185/65R13 W2 front now required with P205/60R13 W2 rear.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used. OR Front – Hoosier P/N 46101 P185/65R13 W2 Rear – Hoosier P/N 46105 P205/60R13 W2
Show 8 more lines
1. It is forbidden to regroove tires. 2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for violation will be the loss of qualifying times and/or the disqualification of race results. 3. Hoosier SRF/SRF3 Decal Placement: Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises."
SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info
wordingSRF Hoosier decal requirement reduced from four decals in specific locations to three decals with simpler placement rules.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows: "Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
slowerSRF brake rotor minimum thickness increases from 12.20mm to 13.25mm, Wilwood vented rotor P/N 800065.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."
wordingSRF3 Hoosier logo placement changes from four decals to three decals in different locations.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.2.B, change as follows: "Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."
fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.
As printed in Fastrack
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1" In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
slowerEP Triumph GT6 switches to three Weber 40 DCOE carbs with 28mm chokes, weight rises 50 lbs to 1990.
As printed in Fastrack
In EP Spec Lines, make the following changes in the "Triumph GT6" spec line: Carburetor No. & Type: (2): "1.5” 1.75" Auto-type carburetor(s)" Notes: "Two (2) 1.75” auto-type carburetors @ 1940 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive."
In GT2 SPEC LINES, GT Engines - PANOZ, classify 2013-2016 Ford EcoBoost Twin Turbo as follows: GT Engines – PANOZ Engine Family Engine Type Bore x Stroke (in.) Disp.
Show 2 more lines
(CC) Head Type Valves /
A specification table follows in the original; it is not shown here.
EP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line
In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows: "B. Aerodynamic Devices 2. Rear wing c. The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule."
A specification table follows in the original; it is not shown here.
fasterGT2 STO aftermarket ABS weight penalty reduced from 100 lbs to 50 lbs.
As printed in Fastrack
In GCR, Appendix K. 2012 STO Rules, O.9., change as follows: "May run OEM ABS or convert to an aftermarket ABS controller with 100 50 lb. weight penalty."
unclearGT2 Pontiac Fiero changes from FWD to RWD; hood bulge permitted for front engine relocation.
As printed in Fastrack
In GT2 Spec Lines, GT2 Cars - PONTIAC, Fiero, change as follows: Drive-line: "FWD RWD" Add to Notes: "Hood bulge permitted as requested for front engine relocation only."
slowerTA2 and STO OEM wings no longer exempt from rear wing height rule at roof peak.
As printed in Fastrack
In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows: "The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule." In GCR, Section APPENDIX K. 2012 STO GENERAL TECHNICAL REGULATIONS, D.4.b., add the following: "Factory wings, and spoilers, and roof vortex generators are permitted, but must be removed if an approved aftermarket wing is installed. OEM aerodynamic devices do not need to adhere to the height rule."
fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.
As printed in Fastrack
In HP Spec Lines "Ford Festiva (88-93)" change as follows: Weight: "1700 1600 *1743 1640 **1785 1680" Notes: "Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."
wordingSRF drivers with disabilities may modify seat and controls for safety and comfort with approval and logbook notation.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.D, add the following: "f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
wordingGT2 Porsche 911 Coupe & Targa may use 993 3.8 RSR rear deck lid or approved aftermarket reproductions.
As printed in Fastrack
In GT2 Spec Lines, GT2 Cars-Porsche, 911 Coupe & Targa., add to Notes the following: "Porsche 911-based race cars (911,963,994), the use of the 993 3.8 RSR rear deck lid/spoiler is permitted. Aftermarket reproductions of the original Porsche Motorsports deck lid provided they faithfully replicate OEM dimensions and functionality, are acceptable for use."
Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following: "SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual." Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038
Show 11 more lines
may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind; maximum of one spring per caliper. 1. Hawk Blue pads P/N 801993 only 2. Wilwood Vented Rotor P/N 800065 only, as delivered, with no machining of any kind. Minimum thickness 13.25mm (0.522") 3. Wilwood universal caliper Kit P/N 1180008 as delivered, caliper only P/N 800038; Wilwood knock back spring P/N 800045 may be used as delivered, with no machining of any kind, and only one spring per caliper 4. Renault caliper rubber bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185A 5. Renault caliper piston may be replaced with P/N 1196184 vented piston as delivered, with no machining of any kind 6. Girling .750" Master Cylinder P/N 880358 as delivered, with no machining of any kind 7. Wilwood .750" Master Cylinder P/N 880357 as delivered, with no machining of any kind 8. Tilton .750" Master Cylinder P/N 880360 as delivered, with no machining of any kind"
otherSRF3 adds HD Oil Cooler P/N G1148500 as alternative to standard cooler P/N G480503.
As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.V.ff, change as follows: "SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
wordingEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.
As printed in Fastrack
In GCR, Section 9.1.5.E., change as follows: 9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished." 9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must remain stock (tolerance of +/-.25mm)."
slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".
As printed in Fastrack
In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."
slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".
As printed in Fastrack
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following changes to the Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
wordingFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.
As printed in Fastrack
In FP Spec Lines, make the following spec line correction: "Volkswagen Rabbit (Includes Convertible Cabriolet)" In HP Spec Lines, make the following spec line correction: "Volkswagen Rabbit 1588 (Includes Cabriolet)" "Volkswagen Rabbit 1715 (Includes Cabriolet)" "Volkswagen Rabbit 1780 (Includes Cabriolet)"
wordingEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.
As printed in Fastrack
In GCR, Section 9.1.5.E.7., change as follows: "e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear disc brakes under this rule. When converting from rear drum brakes to rear disc brakes: 1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on the vehicle’s spec line. 2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock
Show 3 more lines
from converting to rear disc brakes under this rule. 3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes as stock from converting to rear disc brakes under this rule."
unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.
As printed in Fastrack
In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes: "Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."
cars addedGT2 adds Cadillac CTS, Chevrolet Impala/Malibu/Monte Carlo/SS, Dodge Intrepid, Ford Fusion/Taurus, Lincoln MKS, Pontiac G8/GTO/Grand Prix, Toyota Camry, and Gen late Model Stock Car bodies.
As printed in Fastrack
In GCR, Section 4.8.4.2.1., add the following: "Cars in the class must use 1997, through current year, commercially available stock car bodywork. The following make/model bodies are allowed: 1. Cadillac CTS 2. Chevrolet Impala 3. Chevrolet Malibu 4. Chevrolet Monte Carlo 5. Chevrolet SS
Show 12 more lines
6. Dodge Intrepid 7. Ford Fusion 8. Ford Taurus 9. Lincoln MKS 10. Pontiac G8 11. Pontiac GTO 12. Pontiac Grand Prix 13. Toyota Camry Gen late Model Stock Car Bodies are allows: 1. Chevrolet Camaro 2. Ford Mustang 3. Toyota Camry"
EP Request to Update E30 BMW Throttle Body Diameter Verbiage
slower991.2 GT3 Cup throttle body restrictor increases from 65mm to 70mm; 997.2 loses 100 lbs to 2800; Corvette LS engines get larger restrictors across multiple displacements and model years; LS3 and LT1 weight reduced 100 lbs each to 3150.
As printed in Fastrack
In GT2 Spec Lines, GT2 Cars – Porsche, classify 992.1 GT3 Cup as follows: GT2 Cars – Porsche Model Year Body Style Driveline Wheel Base Notes 992.1 GT3 Cup (22-25) 2 Dr RWD 4.0L flat six. 3250lbs. w/60mm Throttle Body Restrictor (TBR). Cars must be prepared in accordance with the appropriate
Show 49 more lines
model/year Porsche factory 911 GT3 Cup parts catalog/service manual. Cars may not be altered in any way except as authorized below. Drivers must have the correct year manuals as they apply to their specific car in their possession. Safety, drivers comfort, driver control and instrumentation items may be modified per the GCR. Original factory installed Matter/ IMV roll cages are allowed. The stock unmodified fuel tank is allowed. Windshield clips must be installed per GCR 9.3 Windshield Clips/Rear Window Straps. All other SCCA safety standards apply. Tires per GCR 9.3 Tires. Lubricants, consumable fluids (brake fluid, coolant etc.) and oil filters are open free. Factory (OEM manufacturer) Lexan front windows allowed as delivered. ABS is allowed. In GT2 Spec Lines, GT2 Cars – Porsche, change Notes as follows: 991.1 GT3 Cup: "3.8L flat six. 3000lbs. w/72mm Throttle Body Restrictor (TBR). Aftermarket header allowed." 991.2 GT3 Cup: "4.0L flat six. 3000lbs. w/65mm 70mm Throttle Body Restrictor (TBR)." 997.2 GT3 Cup: "3.8L flat six. 2900 2800 lbs. Aftermarket header allowed." In GT2 Spec Lines, GT2 – ST, Chevy Corvette (-2013), change as follows: 5665: Restrictor: "81 85mm flat plate" Notes: "GM LS1, LS6. LS1/LS6 C6 Corvettes using the OEM C6 intake manifold and 90 mm throttle body must use a 78mm flat plate restrictor. OEM 75mm throttle body and manifold do not require a restrictor. LS6 may reduce weight by 50 lbs. L S1/LS6 alternate intake manifold, DORMAN part # 615-900." LS2 5967 Restrictor: "83 85mm " L76 5967 Restrictor: "80 83mm flat plate" LS3 6162 Restrictor: "80 83mm flat plate" 6162 GM LS3: Weight: "3250 3150" Restrictor: "74 80mm flat plate" 6162 GM LT1: Weight: "3250 3150" Restrictor: "74 77mm flat plate" In GT2 Spec Lines, GT2 – ST, Chevy Corvette (14-19), change as follows: 5665: Restrictor: "83 85mm flat plate" Notes: "GM LS1, LS6. LS1/LS6 C6 Corvettes using the OEM C6 intake manifold and 90 mm throttle body must use a 78mm flat plate restrictor. OEM 75mm throttle body and manifold do not require a restrictor. LS6 may reduce weight by 50 lbs. L S1/LS6 alternate intake manifold, DORMAN part # 615-900." LS2 5967: Weight: "3100 3000" Restrictor: "83 85mm flat plate" L76 5967 Restrictor: "80 83mm flat plate" 6162 Restrictor: "80 83mm flat plate" 6162 LS3: Weight: "3200 3100" Restrictor: "77 80mm flat plate" 6162 LT1: Weight: "3200 3100" Restrictor: "74 80mm flat plate"
GT2 Allow Larger Air Cooled Engines in Porsche 911 GT2
fasterGT2 Porsche 911 SC gains option of 4.0L 4V engine at 2350 lbs or 4.0L 2V at 2275 lbs.
As printed in Fastrack
In GT Spec Lines, create GT Cars - PORSCHE and classify SC as follows: GT Cars - PORSCHE Model Years Body Style Drive- line Wheel- base (in) Notes SC 1978 2 Dr. Rear engine/RWD 89.45 May use alternate engine bore. 4.0L 2V @2275 lbs. 4.0L 4V @ 2350 lbs.
cars addedM3 E92 classified in GT2 with 3999cc V8, 35mm restrictor, 3300 lbs minimum weight.
As printed in Fastrack
In GT Spec Lines, classify M3 E92 in GT Cars - BMW as follows: GT Cars - BMW Model Years Body Style Drive- line Wheel- base (in) Notes M3 E92 (08-13) 2 Dr. RWD 108.7 Cannot be built to any other rule set.
Show 5 more lines
In GT Spec Lines, classify M3 E92 in GT Engines - BMW - BMW as follows: GT Engines - BMW Engine Family Engine Type Bore x Stroke
A specification table follows in the original; it is not shown here.
What the rules allowed changed as listed; this does not say what any particular car ran.