This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
6 laps are left out as timing errors (far too short to be a lap of this track). The rest of those sessions, sectors included, is used.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Elan DP02/Mazda
P
1
1:32.576Jim Devenport
1:32.872Jim Devenport
1:33.972Jim Devenport
171.9Jim Devenport
25.461Jim Devenport
26.606Jim Devenport
40.217Jim Devenport
Dauntless Stohr
P
2
1:36.516Johnnie Crean
1:36.516Johnnie Crean
1:37.287John Manfroy
160.4John Manfroy
25.956Johnnie Crean
27.257John Manfroy
42.386John Manfroy
Dauntless Stohr
P
1
1:36.516Johnnie Crean
1:36.516Johnnie Crean
1:39.209Johnnie Crean
157.4Johnnie Crean
25.956Johnnie Crean
28.143Johnnie Crean
42.417Johnnie Crean
Dauntless-Stohr P07d
P
1
1:37.287John Manfroy
1:41.818John Manfroy
1:37.287John Manfroy
160.4John Manfroy
26.696John Manfroy
27.257John Manfroy
42.386John Manfroy
Stohr WF1
P
1
1:38.716Kevin Mitz
1:38.716Kevin Mitz
1:39.638Kevin Mitz
155.4Kevin Mitz
26.934Kevin Mitz
28.397Kevin Mitz
43.336Kevin Mitz
Penton Norma M20FC
P
1
1:39.296Joseph Moran
1:39.296Joseph Moran
1:40.832Joseph Moran
149.0Joseph Moran
27.106Joseph Moran
28.111Joseph Moran
43.651Joseph Moran
BMW M3
T1
1
1:46.465Ian Barberi
1:46.465Ian Barberi
1:47.434Ian Barberi
114.9Ian Barberi
28.992Ian Barberi
30.811Ian Barberi
46.263Ian Barberi
BMW M4 GT4
T1
1
1:47.084Drew Delmonico
1:47.084Drew Delmonico
1:47.467Drew Delmonico
161.4Drew Delmonico
29.150Drew Delmonico
30.850Drew Delmonico
46.316Drew Delmonico
Porsche 986 Boxster
T3
1
1:51.337Reto Eberle
128.4Reto Eberle
29.898Reto Eberle
33.530Reto Eberle
54.812Reto Eberle
Mazda RX-7
FP
1
1:55.440Michael Lewis
1:56.121Michael Lewis
1:55.440Michael Lewis
128.8Michael Lewis
31.255Michael Lewis
33.299Michael Lewis
50.847Michael Lewis
Ford Mustang
T1/T3
6
1:55.675Scotty B White
1:55.965Roger Eagleton
1:55.675Scotty B White
137.2Scotty B White
31.598Scotty B White
33.496Scotty B White
50.029Scotty B White
Nissan Sentra SE-R
FP
1
1:55.722Brian Linn
1:57.239Brian Linn
1:55.722Brian Linn
128.3Brian Linn
31.416Brian Linn
33.400Brian Linn
50.478Brian Linn
Volkswagen GTI
FP
1
1:56.016Tim Linerud
2:06.156Tim Linerud
93.4Tim Linerud
33.738Tim Linerud
35.656Tim Linerud
55.246Tim Linerud
Nissan 370Z
T3
1
1:56.241Gamaliel Aguilar-Gamez
1:56.241Gamaliel Aguilar-Gamez
1:56.899Gamaliel Aguilar-Gamez
131.8Gamaliel Aguilar-Gamez
31.456Gamaliel Aguilar-Gamez
33.615Gamaliel Aguilar-Gamez
50.788Gamaliel Aguilar-Gamez
Mazda MIata
FP
1
1:56.276Steven Powers
1:57.032Steven Powers
1:56.276Steven Powers
134.3Steven Powers
31.570Steven Powers
33.696Steven Powers
50.716Steven Powers
Pontiac GTO
T1
1
1:59.123Ed Gless
1:59.760Ed Gless
1:59.123Ed Gless
120.7Ed Gless
32.383Ed Gless
34.587Ed Gless
51.370Ed Gless
Fiat X 1/9
FP
1
1:59.128Daniel Snow
2:00.398Daniel Snow
1:59.128Daniel Snow
137.8Daniel Snow
31.878Daniel Snow
34.053Daniel Snow
52.221Daniel Snow
BMW Z4M
T3
1
1:59.315J. David Orem
2:00.000J. David Orem
1:59.698J. David Orem
128.1J. David Orem
32.480J. David Orem
34.645J. David Orem
51.770J. David Orem
BMW 330ci
T3
1
1:59.844Ron Tanemura
1:59.844Ron Tanemura
1:59.971Ron Tanemura
136.3Ron Tanemura
32.188Ron Tanemura
34.401Ron Tanemura
52.107Ron Tanemura
Porsche 914-4
FP
1
2:15.932Garey Raymond
2:21.274Garey Raymond
2:15.932Garey Raymond
84.8Garey Raymond
37.237Garey Raymond
39.091Garey Raymond
59.604Garey Raymond
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
wordingT3 Porsche Spec Boxster tire rule updates to current SPB rules or any 245 DOT tire.
As printed in Fastrack
In T3 Spec Lines, Porsche Spec Boxster, change Notes as follows: "Must conform to all SPB rules in the PCA rulebook. Each competitor shall have available definitive current documentation of the PCA rules. Tires must meet 2016 Current SPB rules or any 245 DOT tire permitted. No other touring allowances permitted."
Applies to Porsche 986 Boxster on this page: Reto Eberle
wordingT1 cars with aftermarket sequential transmissions get 10-inch max bellhousing; non-sequential cars gain 100 lbs weight break.
As printed in Fastrack
In GCR, Section 9.1.9.1.I.4., change as follows: "Aftermarket sequential transmissions are permitted. Cars with aftermarket sequential shift transmissions shall utilize a 1:1 (or greater/overdriven) ratio in top gear. Transmission location must be OEM. Maximum bellhousing length is 10 inches. Cars that don’t use an aftermarket sequential transmission may decrease their competition weight by 100 lbs."
T3 OEM VW Steering Spindle Replacements 06-10 VW GTI and Jetta
wordingT1 GT4 weights clarified for nine cars, ranging from 3200 lbs Porsche 718 Cayman to 3575 lbs Aston Martin.
As printed in Fastrack
RM 23-04 – Touring 1 weights dated 3/21/2023 As an E&O to the February Fastrack, in T1-GT4 leave weights as follows: Aston Martin Vantage AMR GT4: 3575 Audi R8 GT4: 3550 BMW M4 GT4: 3500 Ford Mustang GT4: 3550 Maclaren 570S GT4: 3450 Mercedes AMG GT4: 3450
Show 3 more lines
Porsche 718 Cayman GT4 CS MR: 3200 Porsche 718 GT4 RS Clubsport: 3450 Toyota Supra GR GT4: 3350
wordingFord Fiesta HP and Chevrolet Sonic FP model year ranges extended from 2016 to 2019.
As printed in Fastrack
In HP, adjust model years of the "Ford Fiesta (11-16)" spec line as follows: "Ford Fiesta (11-16 9)" In FP, adjust model years of the "Chevrolet Sonic (12-16)" spec line as follows: "Chevrolet Sonic (12-16 9)"
fasterT3 Camaro V6 1LE and LT-I4 Turbo 1LE max wheel diameter increases from 18 to 20 inches.
As printed in Fastrack
In T3 Spec Lines, Chevrolet Camaro V6 1LE (2016-), change Max. Wheel Size as follows: "18 x 10 20 x 10" In T3 Spec Lines, Chevrolet Camaro LT-I4 Turbo 1LE (2016-), change Max. Wheel Size as follows: "18 x 10 20 x 10"
slowerT1 Chevrolet Camaro Gen 5, Corvette C5 and C6: engine resleeve restricted to stock parameters only, no longer LS3 bore/stroke.
As printed in Fastrack
In T1 NEW Spec Lines, Chevrolet Camaro Gen 5 (10-15) Including SS, Z28, change Engine Notes as follows: 1130: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1135: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement.May resleeve to stock parameters for engine repair or replacement." In T1 NEW Spec Lines, Chevrolet Corvette C5 (‘97-’04) – Includes: Z06, Coupe, Convertible, change Engine Notes as follows: 1132: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement."
Show 18 more lines
1134: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1136: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1138: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." In T1 NEW Spec Lines, Chevrolet Corvette C6 (05-13) - Includes Z51, GrandSport, Z06, Z06 Carbon, change Engine Notes as follows: 1150: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1160: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1170: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1180: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1190: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement."
wordingFP and HP Sprite, Midget, and Spitfire 1500 intake valve size corrected to 36.6/(1.44).
As printed in Fastrack
In FP Spec Lines, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change Intake Valve Size as follows: "(I) 36.65.3/(1.44)" In FP Spec Lines, Triumph Spitfire Mk. IV & 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire Mk. III & IV 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)"
fasterT1 Corvette C5 gains approved aero parts: carbon rear spoiler, vented front splitter, side skirts, with 50 lb weight reduction allowed.
As printed in Fastrack
In T1 NEW Spec Lines, Chevrolet Corvette C5 (‘97-’04) – Includes: Z06, Coupe, Convertible, Spec Lines 1132-1138, add to Notes as follows: "Any option of OEM Bodywork parts may be used as basis for aero measurements. Rear spoiler max 5” Above bumper allowed. +50lbs. The following parts are permitted, with a 50lb decrease from base weight, in lieu of the aero options permitted in 9.1.9.1.B: (C7Carbon Rear- Spoiler CCC5 EX- RSB-GB, Vented Front Splitter CCC5-FS-GB, Side Skirts CCC5 SS-GB.)"
wordingT3 Mazda RX-8 removes transmission/final drive pairing requirement; T4 removes same requirement, adds Mazdaspeed radiator and coil spring kit.
As printed in Fastrack
In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows: "Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3 transmission must be paired with the listed alternate final drive. Front sway bar permitted 32mm MAX rear sway bar 19 MAX, Front springs max 750, 500 rear. Cold air intake permitted. Header permitted. Aftermarket flywheel and single disc clutch permitted with no weight penalty." In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows: "Mazdaspeed radiator #0000-01-8501 allowed. Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3 transmission must be paired with the listed alternate final drive. Mazdaspeed coil spring kit #QSEA-34-01Z allowed. 60mm flat plate restrictor required. OE Rear spoiler allowed #F151-V4-920F. OE front air dam allowed #F151-V4-900f-BB. Springs Allowed:
Show 2 more lines
(F) Mazda Motorsports- 0000- 04-9700-08 or Eibach- 0800.250.0700 (R) Mazda Motorsports- 0000-04-9400-07 or Eibach 0700.250.0400, and helper 0000-04-9926 allowed. Alternate sway bars allowed max 32mm (f) 19mm (r)."
fasterT3 BMW 320i (14-15) gains aftermarket intercooler permission; T4 loses it.
As printed in Fastrack
In T3 Spec Lines, BMW 320i (14-15), add to Notes the following: "Aftermarket intercooler permitted." In T4 Spec Lines, BMW 320i (14-15), remove from Notes the following: "Aftermarket intercooler permitted."
T1 Request to Remove Expiration from T1 spec lines #1350 & #1370
wordingT1 Dodge Viper ACR / SRT RT-10 and ACR/ACR-X spec lines 1350 and 1370 remove 12/23 expiration.
As printed in Fastrack
In T1 NEW Spec Lines, Dodge Viper ACR / SRT RT-10, change Spec Line Number as follows: "1350 *Spec line Expires 12/23*" In T1 NEW Spec Lines, Dodge Viper ACR/ACR-X, change Spec Line Number as follows: "1370 *Spec line Expires 12/23*"
wordingT3 Pontiac Solstice GXP minimum ride height set to 3 inches.
As printed in Fastrack
In T2 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following: "Minimum ride height is 3 inches." In T3 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following: "Minimum ride height is 3 inches."
T1 New T1 add spec line for C5 corvette LS2 engines (Copy from C6)
cars addedT1 Porsche 997-1 GT3 Cup added at spec line 4210, minimum weight 3050 lbs.
As printed in Fastrack
In T1 Spec Lines, delete the Porsche 996 GT3 Cup car from the standard spec lines and classify "Homologated car" section as follows: T1 – Homologated Cars
A specification table follows in the original; it is not shown here.
fasterT3 Porsche Cayman (09-12) and (13-16) gear and final drive ratios adjusted; 09-12 6-SPD final drive 3.88 to 3.875, PDK 3.909 to 3.250; 13-16 6-SPD final drive 3.89 unchanged, PDK 3.91 to 3.250.
As printed in Fastrack
In T3 Spec Lines, change gear ratios and final drive ratios as follows:
A specification table follows in the original; it is not shown here.
cars addedEP Porsche 944/924S combines 2.5L and 2.7L variants with new weights: 2250–2415 lbs depending on engine and year.
As printed in Fastrack
In EP Spec Lines, delete the Porsche 944/924S 2.5L (2V) (83-88) spec line entirely, and create a new spec line for Porsche 944/924S 2.5L(2V) 2.7L(2V) (83-89) as follows:
A specification table follows in the original; it is not shown here.
fasterFP Toyota Corolla 2TC loses 43 lbs to 1810; HP Corolla loses 50–52 lbs to 1910–2006.
As printed in Fastrack
In FP Spec Lines, Toyota Corolla 2TC (71-74), change weight as follows: "1853 1810" In HP Spec Lines, Toyota Corolla (71-74), change weight as follows: “1960 1910 * 2009 1958 ** 2058 2006”
wordingT3 VW Golf GTI and Golf R TIR location clarified to maximum 60mm from impeller.
As printed in Fastrack
In T3 Spec Lines, Volkswagen GTI (2013), change Notes as follows: "Rear sway bar max 42 mm (body and suspension mounting same as OEM), Any spring up to a maximum spring rate of 800 pounds may be used. Turbo Inlet Restrictor 36mm required max 60mm from impeller. R32 model brake package allowed. Verkline WAS-048 camber arms permitted." In T3 Spec Lines, Volkswagen Golf R (15-16) change Notes as follows: "Max spring rate 800 F&R, Max swaybar 38mm F, 42mm R. 36mm TIR required max 60mm from impeller."
unclearT1-GT4 batch adjustments: five cars lighter, two heavier, restrictors and ECU maps changed, five models now eligible for Runoffs.
As printed in Fastrack
In GCR, Section 9.1.9.1.A.T., change as follows: "Tires- Tires must conform to GCR section 9.3.TIRES and als o must conform to spec line requirements. DOT approved tires are permitted. Slicks conforming to the spec line are permitted." In Touring 1 - Homologated Cars Spec Lines, 4100- BMW M2 ClubSport Racing, change Must Conform To as follows: "Tires conforming to SRO TCX rules allowed. Must meet factory specs." In Touring 1 - Homologated Cars Spec Lines, 4120- Ford Mustang FP350S 2017, change as follows: Must Conform To: "Tires conforming to Trans Am SGT tire rules allowed Must meet factory specs." Chassis Notes: "VIN not required. Additional permitted allowances: DOT tires required. Other consumables are open, alternate
Show 40 more lines
driveshaft permitted, aftermarket wheels and fuel cell per Touring category rules permitted. Shocks conforming to T1 rules permitted. Alternative rear toe links permitted." In T1-GT4 Spec Lines, change Chassis Notes as follows: Aston Martin Vantage AMR GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)** Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Audi R8 GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." BMW M4 GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Chevrolet Camaro GT4-R: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Ford Mustang GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Maclaren 570S GT4: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Mercedes AMG GT4: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Porsche 718 Cayman GT4 CS MR: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Porsche 718 GT4 RS Club-sport: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Toyota Supra GR GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." In T1-GT4 Spec Lines, change as follows: Aston Martin Vantage AMR GT4: Weight: “3575 3490” Performance Control: “SRO power level ECU Map 3 IMSA Map id 11” Chevrolet Camaro GT4-R: Weight: “3375 3435” Performance Control: “63 62mm” Ford Mustang GT4: Weight: “3550 3535” Performance Control: “63 71mm SRO compliant restrictor IMSA ECU Cal” Maclaren 570S GT4: Weight: “3450 3250” Performance Control: “SRO 2019 BOP ECU map SRO Rest 1” Mercedes AMG GT4: Weight: “3450 3470” Performance Control: “Power level 2 map 5” Porsche 718 Cayman GT4 CS MR: Weight: “3200 3250” Performance Control: “54 53.7mm” Toyota Supra GR GT4: Weight: “3350 3315”
slowerT3 Nissan 350Z DE motor loses 75 lbs to 3125; HR motor gains 47mm restrictors, up from 44mm.
As printed in Fastrack
In T3 Spec Lines, Nissan 350ZTrack/ Touring/Standard/Nismo(03-08), change as follows: Weight: "DE Motor: 3200 3125 HR Motor: 3275" Notes: "HR Engine: Two 44mm 47 mm flat plate restrictors required. DE engine: Cold air intake permitted."
wordingT3 2010 Mustang GT 4.6 now allows 2013-14 GT style front/rear fascia, hood, and associated assemblies.
As printed in Fastrack
In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), add to Notes the following: "2010 models may update the front and rear fascia, hood and associated assemblies to the 2013-14 GT style."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
In EP spec line, Triumph GT6, make the following change in the Notes section: "Two (2) 1.75” auto-type carburetors @ 1970 40 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive. Three (3) Weber 40mm DCOE w/28mm venturi on individual runner manifold @ 2020 lb."
fasterT3 BMW SpecE46 minimum weight drops 50 lbs to 2850.
As printed in Fastrack
In T3 Spec Lines, BMW SpecE46, change as follows: Min Weight: "2900 2850" Notes: "Must conform to all SpecE46 rules Version 2.10. SpecE46 spec tire permitted or any DOT permitted up to 225 permitted. No other touring allowances permitted. Engines may not be modified unless specified in the Spec E46 rules and must conform to touring tech procedures. Driver must possess a current copy of the rules. Dyno results do not ensure engine compliance. SE46 HP limit does not apply."
fasterEP Honda S2000 fuel injected throttle body inside diameter increases from 62mm to 64mm.
As printed in Fastrack
In EP spec line, Honda S2000, make the following changes to its spec line: Fuel Injected Equipped Throttle Body Inside Diameter: "62 64" Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .500”. An adaptor plate can be used to mount the 62mm throttle body from '00-05 to the '06-09 intake manifold. The adaptor plate can be no more than 1.25" thick, and its bore must not exceed the "Fuel Injected Equipped Throttle Body Inside Diameter" maximum spec of 64mm."
slowerT3 Subaru STI (15-20) minimum weight increases 100 lbs to 3450; all three STI variants get larger turbo inlet restrictors.
As printed in Fastrack
In T3 Spec Lines, Subaru WRX STI (03-07), change Notes as follows: "Killer B intake pipe #EJTI and coupler permitted. 37mm 39mm TIR required." In T3 Spec Lines, Subaru STI (15-20), change as follows: Min Weight: "3350 3450" Notes: "Killer B intake pipe #EJTI and coupler permitted. 37mm 40mm TIR required." In T3 Spec Lines, Subaru Legacy GT/Spec B (05-09), change Notes as follows: "Killer B intake pipe #EJTI and coupler permitted. 37mm 39mm Turbo inlet restrictor required."
wordingEP Triumph TR8 dry sump allowance moved from carburetor line to notes section.
As printed in Fastrack
In EP spec line, Triumph TR8 (78-81), move the "Dry sump allowed" wording to the appropriate location as follows: Carburetor. No. & Type: “Zenith Stromberg carbs or fuel injection. Dry sump is allowed.” Notes: “Comp. Ratio limited to 12.0:1, Valve lift limited to .500”. Dry sump is allowed.”
In GCR, Section 9.1.9.2.D.1.g.3., change as follows: "Batteries may be replaced provided the replacement is capable of starting the car. Batteries may not be relocated unless noted on the spec line. Batteries must be adequately secured. Battery labeling must conform to 9.3.35.D. with those of an alternate manufacturer, provided they are of similar amp-hour capacity, size and within 10% of OEM weight."
T3 Open Strut Tower Brace Options for Ford Mustang V6 (11-14)
cars addedT4 now permits C-Spec cars to compete alongside B-Spec cars.
As printed in Fastrack
In GCR, Section 9.1.9.2., change as follows: "Touring car eligibility: Cars are eligible for the class they are listed with a specification line and with the specific allowances permitted. In addition, T2-T4 cars may race one class up in touring classes above their specification line class as long as they are a legal T2-T4 car and conform to their specification line allowances as classified. Cars conforming to C-Spec rules are permitted to compete in Touring 4."
wordingT2-T4 spec lines for 46 cars expire 12/31/24; appeal required to continue.
As printed in Fastrack
In T2-T4 Spec Lines, add **This Spec line will expire 12/31/24, Please submit to appeal** to Notes to the following Spec Lines: T2: Acura TL SHAWD (10-13) Audi S4 (12-14) Audi S5 (13-14) Audi TT RS (2018-) Cadillac ATS-V (16-17)
Show 46 more lines
Cadillac CTS-V (06-07) Chevrolet Camaro SS (98-02) Honda Civic (2017-) Saturn Sky / Convertible (07-09) Subaru Impreza WRX STi (03-07) Subaru Impreza WRX STi (08-11) T3: Audi S4 (10-11) Audi S4 (12-14) Audi TTS Coupe (10-11) Cadillac ATS (2015) Chevrolet Cobalt (05-07) Dodge SRT-4 (03-05) Ford Fiesta ST (2014-) Hyundai Genesis Coupe (2010-) Hyundai Veloster Turbo (18-21) Mazda RX-8 Base/R3/Sport/ GT (04-12) Mini Cooper S (2016-) Subaru WRX (02-05) Toyota Camry (11-15) T4: Acura Integra GS-R VTEC (3 or 4 door) (94-01) Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05) BMW 320i (14-15) Chevrolet Cobalt SS, Sport Coupe (06-10) Chevrolet Sonic RS (2011-) Chrysler/Dodge Neon ACR SOHC (4 door) (01-02) Dodge Dart (14-15) Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99) Fiat 500 Abarth (12-14) Ford Focus SVT (02-04) Ford Focus ZX4 ST (05-06) Ford Focus (08-11) Ford Mustang V-6 (01-04) Honda Accord LX & EX (03-07) Honda Accord LX-S/EX/EX-L (08-12) Honda Civic Coupe Si (99-00) Honda Civic SI (02-03) Hyundai Elantra GLS (11-12) Hyundai Tiburon V-6 (03-08) Hyundai Veloster Turbo/ R-Spec (14-15) Kia Forte Koup and Sedan LX/EX (10-13) Kia Forte Koup and Sedan SX (10-13) Kia Forte Koup (14-15) Mazda Protégé ES (2000) Mazda Protégé 5 (02-03)
removedT1 NEW class removes 23 spec lines including Acura NSX, Ferrari, Porsche 996, Nissan Z cars, and others; Porsche 997 spec line 1680 expiration removed.
As printed in Fastrack
In GCR Contents, change as follows: "9.1.9.1 TOURING (T1) CATEGORY NEW T1 NEW" In GCR, Section 9.1.9.1.Touring (T1) NEW Category Specifications, change as follows: "9.1.9.1.Touring (T1) NEW Category Specifications" In T1 NEW Spec Lines, change as follows: "9.1.9.1.A T1 NEW Spec Lines" "T1 NEW"
Show 26 more lines
In T1 NEW Spec Lines, delete the following Spec Lines in their entirety: "Acura NSX (Spec Line 1000) Acura NSX Turbo (Spec Line 1010) Acura NSX Turbo World Challenge (Spec Line 1020) Audi TTRS (GTS 2011 Spec) (Spec Line 1040) Dodge Viper ACR/ACR-X (Spec Line 1360) Ferrari 360 (Spec Line 1400) Ferrari 430 (Spec Line 1410) Ferrari 430 Challenge (Spec Line 1420) Mazda MX-5 (06-15) (Spec Line 1520 and 1530) Mazda RX-7 (Spec Line 1540) Nissan GTR (Spec Line 1550) Nissan 350/370Z (Spec Line 1560) Nissan 370Z Supercharged (Spec Line 1570) Nissan 350Z (Spec Line 1580) Nissan 350Z/370Z (Spec Line 1590) Porsche Cayman/S/GTS (05-15) (Spec Line 1600, 1610 and 1620) Porsche Cayman GTS (2011) (Spec Line 1630) Porsche 928 S4 Porsche 928 GTS-R (Spec Line 1640) Porsche 996 (Spec Line 1650) Porsche 996 TT OEM (Spec Line 1660) Subaru WRX, WRX STI (05-2020) (Spec Line 1700) Toyota Celica All-Trac (Spec Line 1710) Toyota Supra MK4 (Spec Line 1720)" In T1 NEW Spec Lines, Porsche 997, change Spec Line Number as follows: "1680 *Spec line Expires 12/23*"
fasterT3 Spec Z 350Z rear wheel width increases to 10 inches; HR Engine restrictors change from 42mm to 44mm.
As printed in Fastrack
In T3 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo Spec Z (03-08), change as follows: Max Wheel Size (inch): "18 x 9 (F) 18 x 10 (R)" Notes: "Nissan Motorsports: Shock Front left P/N E6110-SZ350 & Front right E6111- SZ350 & rear E6210-SZ350, springs front P/N 54010-SZ350 & rear 55020- SZ350, F&R 5600S-SZ350, Front sway bar max 37mm. Rear sway bar max 25mm, Bushings P/N (54541, 54560, 55045, 55148, 55149, 55152, 55153, 55158, 56218) - RRZ30 allowed. Nismo flywheel permitted. SPC Control Arms 72125 and 72123 are allowed. HR Engine: Two 42mm flat plate restrictors required. Zspeed and Z1 alternative clutch slave permitted. Must conform to all SpecZ 2018 Edition rules. No other touring allowances beyond 2018 SpecZ edition rules or allowances listed here. Nissan brake part numbers NISMO Race Front Caliper Kit 41001-FR350, NISMO Front Rotor-RIGHT 40206-
Show 3 more lines
SZ350, NISMO Front Rotor-LEFT 40207-SZ350 permitted. 44011-RC350 rear caliper kit permitted, 43206-SZ350 Right rotor permitted, 43207-SZ350 Left rotor permitted. Car must conform to the Official 2024 Spec Z Rules. HR Engine: Two 44mm flat plate restrictors required. Tires must conform to Spec Z rules. Competitor must be able to provide a copy of the current rules."
suspension & brakesT3 Nissan 350Z and 370Z now allow brake booster vacuum regulator, must not be in-car adjustable.
As printed in Fastrack
In T3 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo (03-08), add to Notes as follows: "Brake booster vacuum regulator allowed, cannot be in-car adjustable." In T3 Spec Lines, Nissan 370Z, incl. Nismo (2009-2022), add to Notes the following: "Brake booster vacuum regulator allowed, cannot be in-car adjustable."
Applies to Nissan 370Z on this page: Gamaliel Aguilar-Gamez
fasterT3 Ford Mustang 4.6L restrictor holes increased from 40 mm to 45 mm.
As printed in Fastrack
In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), change Notes as follows: "A flat plate restrictor with two 40 mm 45mm holes required directly behind throttle body."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
T3 Appeal for Retention of T3 Mazda RX-8 Spec Line (Letter #35378)
In HP Spec Lines, delete the following redundant spec lines in their entirety: Spec line #10 - VW Rabbit Cabriolet 1780 Spec line #3 - VW Scirocco 1588 Spec line #4 - VW Scirocco 1780 (8-valve) (83-88) Spec line #5 - VW Scirocco 1588
unclearT3 and T4 Mazda RX-8 may remove or disable factory oil injection system.
As printed in Fastrack
In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows: "OEM oil injection system may be removed or disabled." In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows: "OEM oil injection system may be removed or disabled."
wordingFP Honda CRX 84-87 can replace plastic front header, rocker skirt, door cap panels with stock-appearance replicas in alternate materials.
As printed in Fastrack
In FP spec line "Honda CRX / CRX Si (84-87)", add the following wording to the Notes section: "The plastic OE front header/nose body panel, lower rocker side-skirt, and lower door cap panel can be replaced by a replica, which may be constructed of an alternate material, provided its appearance remains stock."
slowerFP Acura Integra and Honda Civic models now require 55mm Flat Plate Intake Restrictor.
As printed in Fastrack
In the following FP spec lines, add the following wording to the Notes section: Acura Integra (90-93) Acura Integra LS (94-01) Acura Integra GSR (92-93) Honda Civic Del Sol VTEC (94-97) Honda Civic Si (99-00) "55mm Flat Plate Intake Restrictor is required."
slowerT2, T3, T4 driveshafts may use alternative materials or one-piece units; non-OEM adds 25 lbs.
As printed in Fastrack
In GCR Section 9.1.9.2.D.4.b., add the following: "6. T2-T3- Driveshafts may be replaced with alternative materials ie. carbon fiber, aluminum, steel. Two-piece driveshafts may be replaced with one-piece units. If non-OEM driveshaft is used, add 25 lbs."
wordingAudi S4 00-02 in T3 must compete in 3 Super Tour events before Runoffs eligibility.
As printed in Fastrack
In T3 Spec Lines, Audi S4 (00-02), add to Notes as follows: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
wordingEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.
As printed in Fastrack
Spec Lines, make the following changes to the two Mazda RX-8 spec lines. Remove spec line entirely: Mazda RX-8 (04-11) Remove the wording "alternate": Mazda RX-8 (04-11)(alternate) Spec Mazda (SM/SMX) None.
unclearFord Mustang GT 5.0L and V6 now permit Track/Performance Package parts in T2 and T3.
As printed in Fastrack
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes as follows: "Track/Performance Package parts permitted." In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows: "Track/Performance Package parts permitted." In T3 Spec Lines, Ford Mustang V6 (15-17), change Notes as follows: "Track/Performance package allowed."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
fasterT2-T4 Ford Mustangs: remove 25 lbs penalty for non-OEM driveshaft, clarify alternate driveshaft allowances.
As printed in Fastrack
In GCR Section 9.1.9.2.D.4.b.6., remove as follows: "If non-OEM driveshaft is used, add 25 lbs." In T2 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows: "Driveshaft from Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang Boss 302 (12-13), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang GT 5.0L (11-14)ki, change Notes as follows: "Alternate metallic driveshaft is allowed."
Show 12 more lines
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L (05-10), change Notes as follows: 'An Aluminum driveshaft is allowed." "Alternate metallic driveshaft is allowed." In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), change Notes as follows: "An Aluminum driveshaft is allowed." "Alternate metallic driveshaft is allowed." In T3 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows: "Driveshaft from Alternate metallic driveshaft is allowed."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
cars addedT3 BMW Z4 3.0si expands to include 3.0i Roadster and Coupe (07-08); hardtop permitted with positive fasteners.
As printed in Fastrack
In T3 Spec Lines, BMW Z4 3.0si, & Coupe (07-08) change Model and add to Notes as follows: "BMW Z4 3.0si, 3.0i, Roadster & Coupe (07-08)" Notes: "Any OEM or aftermarket hardtop permitted that retains the OEM roof silhouette (if a hardtop is used, latches shall be replaced with positive fasteners)."
fasterT3 Honda Civic Si (2017-2021) restrictor removed, weight to 2950 lbs, Runoffs eligibility requires 3 Super Tour events.
As printed in Fastrack
In T3 Spec Lines, Honda Civic Si (2017-) with 2900 weight, change as follows: Model: "Honda Civic Si (2017-2021)" Restrictor: "36mm TIR" Add to Notes: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**" In T3 Spec Lines, Honda Civic Si (2017-), change as follows: Model: "Honda Civic Si (2017-2021)" Restrictor: "36mm TIR" Weight (lbs): "30752950"
Show 1 more lines
Add to Notes: "**This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
wordingT3 Subaru STI (15-20) and WRX STI (03-07) permitted to use OEM spec block #IAG-ENG-S550 and head studs.
As printed in Fastrack
In T3 Spec Lines, Subaru STI (15-20), add to Notes the following: "OEM spec block permitted # IAG-ENG-S550, Head studs permitted." In T3 Spec Lines, Subaru WRX STI (03-07), add to Notes the following: "OEM spec block permitted # IAG-ENG-S550, Head studs permitted."
fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.
As printed in Fastrack
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1" In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
cars addedBMW M4 GT4 (G82) added to T1 GT4 at 3525 lbs minimum weight with Red power stick control.
As printed in Fastrack
In T1 GT4 Spec Lines, SL#4030, change as follows: Model: "BMW M4 GT4 (F82)" Performance Control: "Gold power stick Red power stick" In T1 GT4 Spec Lines, classify BMW M4 GT4 (G82) as follows:
A specification table follows in the original; it is not shown here.
wordingT3 VW Golf R (12-13 and 15-18) 36mm TIR placement now allows OEM turbo inlet, removing 60mm distance limit from impeller.
As printed in Fastrack
In T3 Spec Lines, Volkswagen Golf R (12-13), change Restrictor Required as follows: "36mm TIR max 60mm from impeller TIR may be placed in the OEM turbo inlet as long as the restriction is entirely within the leading edge of the housing." In T3 Spec Lines, Volkswagen Golf R (15-18), change Restrictor Required as follows: "36mm TIR max 60mm from impeller TIR may be placed in the OEM turbo inlet as long as the restriction is entirely within the leading edge of the housing."
T3 Redundant Verbiage Regarding Mustang Spec Lines for Driveshaft
wordingT2 and T3 Mustang spec lines remove redundant driveshaft alternate/aluminum allowance wording.
As printed in Fastrack
In T2 Spec Lines, change Notes as follows: Ford Mustang V6 (11-14): "Alternate driveshaft is allowed." Ford Mustang Boss 302 (12-13): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (11-14): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (15-17): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (2018-): "Alternate driveshaft is allowed. Springs up to 800#/in front and rear permitted. Alternate metallic driveshaft permitted." Ford Mustang Coupe GT & Shelby GT 4.6L (05-10): "Alternate driveshaft is allowed."
Show 4 more lines
In T3 Spec Lines, change Notes as follows: Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10): "Alternate driveshaft is allowed." Ford Mustang V6 (11-14): "Alternate driveshaft is allowed." Ford Mustang V6 (05-10): "An Aluminum driveshaft is allowed."
fasterT1 GT4 Spec Line 4020 restrictor opens from 44mm to 45mm, minimum weight drops to 3400 lbs.
As printed in Fastrack
In T1 GT4 Spec Lines, Spec Line 4020, change as follows: Performance Control: Power level 2020, 44mm 45mm SRO compliant restrictor" Min. Weight with driver (LBS): "3550 3400"
wordingT2, T3, T4 fuel cell installations may remove charcoal canisters, emissions valves, and sensors.
As printed in Fastrack
In GCR, Section 9.1.9.2.D.1.c. add the following: "5. Removal of ancillary fuel tank equipment charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket fuel cell installations."
wordingT2, T3, T4 brake component wording clarified: 2-piece rotors allowed in T2 within 5% OE diameter, T3 within 2% OEM diameter.
As printed in Fastrack
In GCR, Section, 9.1.9.2.D.6. Brakes, change as follows: "a. Components 1. The make and material of brake pads and linings may be changed. 2. Brake fluid may be substituted with any brake fluid. 3. Brake rotor dust shields may be removed or replaced to accommodate brake ducts. 4. Flexible rubber brake lines may be replaced with Teflon lined, metal braided hoses. 5. Any brake ducts are permitted, but they must serve no other purpose. Fender liners may be modified solely for routing and attachment of brake ducts. Duct intake openings may be created by the opening of 2 sections up to 14.5 square inches each in
Show 10 more lines
the front fascia. The stock headlamp location is not permitted for brake ducting. Two alternative duct openings may be created by the removal of the fog lights or 2 sections up to 14.5 square inches each of stock false grills originally located in the front fascia. 6. Stock replacement brake rotors may be obtained from sources other than the manufacturer provided they are the exact equivalent of the stock rotors. In T2 only - 2-piece rotors with ferrous metal rotor disks and aluminum hats are allowed, must be within 5% of OE diameter. In T3 only - 2-piece front rotors with ferrous metal rotor disks and aluminum hats are allowed, must be within 2% of OEM diameter. Drilled and slotted rotors are permitted. 7. Parking brakes, mechanisms, and actuating components may be removed. 8. Brake vacuum reservoirs sized 0.50 gallons or smaller are permitted. The port or fitting at the vacuum source may not be modified, enlarged or relocated. The vacuum reservoir and brake booster must be a closed system."
wordingT2, T3, T4 fuel cell cars may remove charcoal canisters, emissions valves, and sensors.
As printed in Fastrack
In GCR, Section, 9.1.9.2.D.1.c., add the following: "5. Removal of ancillary fuel tank equipment; charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket fuel cell installations."
wordingT3 and T4 Mazda RX-8 and MX-5 permit transmission kit #0000-02-5700.
As printed in Fastrack
In T4 Spec Lines, add the following to Notes: Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted. Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted." In T3 Spec Lines, add the following to Notes: Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted." Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted."
wordingT1 Corvette may roll or flatten wheel opening lips for tire clearance; plastic fenders may remove lips if edge thickness matches basic material.
As printed in Fastrack
In GCR, Section 9.1.9.1.A.2,, add the following: "It is permitted to roll under or flatten any interior lip on the wheel opening for tire clearance. Cars with plastic/composite fenders may remove any interior wheel opening lip, but the resulting material edge shall be no thinner than the basic fender material thickness. Non-metallic inner fender liners may be removed. Vents may be added to fenders."
wordingT4 BMW 320i 14-15 Spec Line expires 12/31/24 removed; Turner Motorsports intercooler #024703TMS02 allowed.
As printed in Fastrack
In T4 Spec Lines, BMW 320i (14-15), change Notes as follows: "**This Spec line will expire 12/31/24, Please submit to appeal** Turner Motorsports intercooler #024703TMS02 allowed."
T3 Classification for a 2005 Cadillac CTS 3.6 liter 6 speed manual
fasterT3 Subaru WRX STI 03-07 drops 100 lbs to 3200; Legacy GT/Spec B 05-09 drops 150 lbs to 3200.
As printed in Fastrack
In T3 Spec Lines, Subaru WRX STI (03-07), change Weight as follows: "3300 3200" In T3 Spec Lines, Subaru Legacy GT/Spec B (05-09), change Weight as follows: "3350 3200"
T3 Request to Move Spec Mustang to Touring 3 (from T2)
fasterT3 Ford Mustang V6 (11-14) and (15-17) now permit cold air intake.
As printed in Fastrack
In T3 Spec Lines, Ford Mustang V6 (11-14), add to Notes the following: "Cold air intake permitted." In T3 Spec Lines, Ford Mustang V6 (15-17), add to Notes the following: "Cold air intake permitted."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
In T2, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Acura TL SHAWD (10-13) Audi S4 (12-14) Audi S5 (13-14) Audi TT RS (2018-) Cadillac ATS-V (16-17) Cadillac CTS-V (06-07) Chevrolet Camaro SS (98-02)
Show 49 more lines
Honda Civic Type-R (2017-) Saturn Sky / Convertible (07-09)" In T3, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Audi TTS Coupe (10-11) Cadillac ATS (2015) Chevrolet Cobalt (05-07) Dodge SRT-4 (03-05) Ford Fiesta ST (2014-) Hyundai Genesis Coupe (2010-) Hyundai Veloster Turbo (18-21) Mini Cooper S (2016-) Toyota Camry (11-15)" In T4, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Acura Integra GS-R VTEC (3 or 4 door) (94-01) Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05) Chevrolet Cobalt SS, Sport Coupe (06-10) Chevrolet Sonic RS (2011-) Chrysler/Dodge Neon ACR SOHC (4 door) (01-02) Dodge Dart (14-15) Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99) Fiat 500 Abarth (12-14) Ford Focus SVT (02.5-04) Ford Focus ZX4 ST (05-06) Ford Focus (08-11) Ford Mustang V-6 (01-04) Honda Accord LX & EX (03-07) Honda Accord LX-S/EX/EX-L (08-12) Honda Civic Coupe Si (99-00) Honda Civic SI (02-03) Hyundai Elantra GLS (11-12) Hyundai Tiburon V-6 (03-08) Hyundai Veloster Turbo/ R-Spec (14-15) Kia Forte Koup and Sedan LX/EX (10-13) Kia Forte Koup and Sedan SX (10-13 Kia Forte Koup (14-15) Mazda Protégé ES (2000) Mazda Protégé 5 (02-03) Mazda6 s (03-07) Mitsubishi Eclipse GT (00-05) Nissan Sentra SER (02-03) Pontiac Firebird V-6 (96-02) Scion tC (03-07) Subaru Impreza (non-turbo) (04-06) Toyota Celica GT (00-05) Toyota Celica GTS/GT (00-05) Volkswagen Golf TDI (2010) Volkswagen Passat (12-14) Volkswgen Passat TDI (12-14) Volkswgen Passat 1.8T (2014-)"
cars addedF Production now allows GT-Lite cars meeting Appendix N specifications to compete, effective 2025-01-01.
As printed in Fastrack
“(Effective January 1, 2026) (Effective January 1, 2025)." Any GT-Lite (GTL) car meeting all of the requirements of Appendix N GT-LITE CATEGORY SPECIFICATIONS for inclusion into F PRODUCTION" may compete in the F-Production class. For GTL cars competing in FP, the level of preparation and modifications will be determined by Appendix N and not by PCS 9.1.5.”
unclearT1 E46 M3 Spec Line 1050 allows VAC Motorsports throttle body VAC-TB-S54 on 3.250L engine instead of Dinan.
As printed in Fastrack
In T1 Spec Lines, E46 M3 Spec Line # 1050, change Engine Notes as follows: "Dinan Throttle Body #D760-3400 VAC Motorsports #VAC-TB-S54 allowed on the 3.250L."
wordingPrototype Staudacher and unrestricted engine notes corrected for minimum weight wording.
As printed in Fastrack
In Prototype Engine Table, Spec Line B, change the notes as follows: "Staudacher cars may run 950 lb min. wt. minimum weight with 38.5mm flat plate intake restrictor." In Prototype Engine Table, Spec Line D, change the notes as follows: "No restrictor required at 1150 lb min. wt. minimum weight."
wordingPrototype class renamed from P1 to P, affecting designation throughout rules with no performance changes.
As printed in Fastrack
In Categories and Classes, GCR section 9.1, change as follows: "9.1.8. SPORTS RACING CATEGORY CLASSES A Sports Racing (ASR) Regional Class Prototype 1 (P1)" In Homologation Requirements, GCR section 9.2.2, change as follows: "All Formula, Sports Racing, and P1, and P2 cars must be constructed in strict accordance with the rules and regulations contained in the current GCR unless specifically excepted." In Non-Metallic Wheel/Chassis Construction, GCR section 9.3.37, change as follows:
Show 20 more lines
"Non-metallic wheel construction is prohibited. Non-metallic chassis construction is prohibited, except in ASR, P1, FS and FA." In Appendix B, GCR section 1.4.2.G, change as follows: "It is preferable not to combine GT1, AS, T1, T2, T3, and STU with P1, P2, SRF, FP, HP, or GTL." In Appendix C, GCR section 2.6.G, change as follows: "A 14 or 15 year-old must complete his first SCCA driver school in a car not classed in GT1, GT2, FA, FB, F S, ITR, ASR, P1, P2, or T1." In Appendix E, section 1, change as follows: "Depending on the length and banking of the oval course being used, it is recommended that Regions consider restricting the faster classes (GT1, FA, and P 1) from competition at oval track events." In Sports Racing Category, GCR section 9.1.8.1, change as follows: "The SCCA Sports Racing Category shall be for automobiles which are designed and constructed for road racing competition, offering provisions for a driver and passenger, or a driver alone (single-seater). They shall conform to the following requirements. Sports Racers Cars except SRF & SRF3 homologated prior to 1-1-2014 are eligible to compete as P1 or P2 as long as they meet applicable class rules,; no re-homologation is required." "Single seat Formula car chassis (Ex.: FA, FC, FF, FV) fitted with enclosed bodies (as specified in these rules) may run in a Sports Racing/Prototype Class (ASR, P 1, P2) provided they comply with the requirements of the Classification Specification and GCR Section 9." In Sports Racing Category, GCR section 9.1.8.2, change as follows: "In an effort to control shock/damper technology and cost to a level reasonable for Road Racing, in ASR, P1, and P2, any fluid dampers are allowed with the following restrictions:"
cars addedFP GTL Volkswagen Jetta Mark IV 4dr FWD 98.2 wheelbase newly classified.
As printed in Fastrack
In FP Spec Lines, Appendix N, GTL-FP Cars - Volkswagen, classify Jetta Mark - IV as follows: GTL-FP Cars - VOLKSWAGEN Model Years Body Style Drive-line Wheelbase (in) Notes Jetta Mark - IV 4dr FWD 98.2
inductionFP Spec Lines option: carburettor chokes permitted as alternative to SIR, same size as listed SIR.
As printed in Fastrack
In FP Spec Lines, Appendix N: L.9, Fuel Injection System, add the following: "As an option, induction system “Chokes” may be used where a SIR is required. Said chokes shall be fitted to each barrel of carburetor/throttle body and all airflow into engine must pass through them. Choke size will be the same as listed SIR unless noted."
unclearT1 Mustang Spec 1430 restrictor opens 60mm to 65mm; Spec 1460 weight rises to 3500 lbs, restrictor 70mm; Corvette 1190 restrictor opens 67mm to 70mm; BMW 1090 restrictor narrows 40mm to 35mm; BMW 1100 weight rises to 3350 lbs.
As printed in Fastrack
In T1 Spec Lines, change Weight, Restrictor Required and/or Notes as follows: Mustang - Spec Line 1430: Restrictor Required: "60mm 65mm - FPR" Mustang - Spec Line 1460: Weight: "3425 3500" Restrictor Required: "70mm - FPR" Corvette Spec Line 1190: Restrictor Required: "67mm 70mm - Flat Plate"
Show 5 more lines
BMW - Spec Line 1090: Required Restrictor: "(2) X 40mm 35mm diameter hole inlet restrictor plate required" Chassis Notes: "This spec line is set to expire 12/31/25." BMW - Spec Line 1100: Minimum Weight: "3150 3350”
fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.
As printed in Fastrack
In HP Spec Lines "Ford Festiva (88-93)" change as follows: Weight: "1700 1600 *1743 1640 **1785 1680" Notes: "Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."
fasterT1 Honda S2000 minimum weight reduced from 2950 lbs to 2900 lbs.
As printed in Fastrack
In T1 Spec Lines, Honda S2000, Spec Line 1530, change as follows: Minimum Weight: "2950 2900" Chassis Notes: "This spec line is set to expire as of 12/31/2025 if not represented in Majors competition in 2025."
wordingT1 BMW E46 M3 permits BMW #GS7D36SG aftermarket sequential transmission in SL# 1060 and 1070.
As printed in Fastrack
In T1 Spec Lines, BMW E46 M3, add to Chassis Notes the following: SL# 1060: "BMW #GS7D36SG transmission permitted as an aftermarket sequential option." SL# 1070: "BMW #GS7D36SG transmission permitted as an aftermarket sequential option."
fasterT1 Mustang Darkhorse R gets 315 front and rear tyres, loses 500 lbs minimum weight to 3600.
As printed in Fastrack
In T1 Spec Lines, Mustang Darkhorse R (Mustang Challenge) Spec Line- 4119, change as follows: Tire size: "305 315 (f) 315(r)" Performance Control: "TBD" Min. Weight with driver (LBS): "10.5 (f) 11 (r) 3600" Chassis Notes: "Must conform to Mustang Challenge Rules. Tires conforming to Mustang Challenge rules are permitted. **This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
wordingClass P adds clarification notes on restrictor requirements, throttle bodies, Mazda 12A engine spec, and P2 auto-based engine rules.
As printed in Fastrack
In P Engine Table, Spec Line D notes, add the following: "No restrictor required at 1150 lbs. minimum weight." In P Engine Table, Spec Line G notes, add the following: "Group CN non-composite chassis with Honda K20A-FD2 may use unrestricted individual throttle bodies at 1500 lbs. minimum weight." In P Table 1, Beasley B2 spec line notes, add the following: "Engine must be Mazda 12A rotary with 40.5mm venturi. Car must comply with all other Prototype requirements." In P Table 1, P2 cars built to 2000cc auto-based specification spec line notes, add the following:
Show 3 more lines
"Car must comply with all other P2 rules applicable to cars using stock production-based four-cylinder automotive engines. Note: Competitors are also free to modify their cars to comply with the general Prototype rules and Engine Table Spec Line H instead."
unclearT3 BMW Spec E46 rules updated to Version 3.0 from Version 1.1.
As printed in Fastrack
In T3 Spec Lines, BMW Spec E46, change Notes as follows: "Must conform to all SpecE46 rules Version 2.10. Version 1.1 dated Jan. 6, 2025. Version 3.0."
FP Base Weight Adjustment for H-Production X1/9 Spec Lines
unclearBMW Spec E46 in T3 updates to SpecE46 rules Version 3.0.
As printed in Fastrack
In T3 Spec Lines, BMW Spec E46, change Notes as follows: "Must conform to all SpecE46 rules Version 2.10. Version 1.1 dated Jan. 6, 2025. Version 3.0."
unclearP class 13B rotary engine restrictor changes to 40mm SIR fuel injection or 41.5mm venturi carburetor.
As printed in Fastrack
Effective 9/1/25 in Prototype Engine Table, Spec Line K, change the restrictor as follows: "40mm SIR with fuel injection or 41.5mm venturi with carburetor"
P Add Radical Cup series Radical SR3 spec line to Table 1
wordingPrototype P2 cars may now run P2 spec or modified Prototype spec in Prototype class; clarified language and added Radical Cup series table.
As printed in Fastrack
Effective 9/1/25, in Prototype, GCR section 9.1.8.B.K, change as follows: "P2 cars may compete in either the Prototype class or the P2 class but must participate in the Prototype class to the extent necessary to qualify for an invitation to the Runoffs in Prototype. P2 cars may be modified to comply with the general Prototype rules and Prototype Engine Table or may continue to run in P2 specification in the Prototype class as permitted in Table 1 below." Table 1 (Spec Line Cars)
A specification table follows in the original; it is not shown here.
wordingEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.
As printed in Fastrack
In GCR, Section 9.1.5.E., change as follows: 9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished." 9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must remain stock (tolerance of +/-.25mm)."
slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".
As printed in Fastrack
In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."
slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".
As printed in Fastrack
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following changes to the Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
wordingFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.
As printed in Fastrack
In FP Spec Lines, make the following spec line correction: "Volkswagen Rabbit (Includes Convertible Cabriolet)" In HP Spec Lines, make the following spec line correction: "Volkswagen Rabbit 1588 (Includes Cabriolet)" "Volkswagen Rabbit 1715 (Includes Cabriolet)" "Volkswagen Rabbit 1780 (Includes Cabriolet)"
wordingEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.
As printed in Fastrack
In GCR, Section 9.1.5.E.7., change as follows: "e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear disc brakes under this rule. When converting from rear drum brakes to rear disc brakes: 1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on the vehicle’s spec line. 2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock
Show 3 more lines
from converting to rear disc brakes under this rule. 3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes as stock from converting to rear disc brakes under this rule."
wordingT3 and T4 Mazda MX-5 Miata models add approved gear kit PT#-0000-02-6100 to notes.
As printed in Fastrack
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T3 Spec Lines, Mazda MX-5 Miata (16-18), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, add to Notes the following: "Gear kit Kit PT#- 0000-02-6100."
wordingT4 Mazda MX-5 Miata/Club/RF (19-24) and (16-18) remove discontinued hardtop part #0000-07-5901; T3 MX-5 Miata (16-18) and Global Cup ND (16-21) same.
As printed in Fastrack
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must remain stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5804-01). Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs #0000-04-9700-08, springs up to 500lb front and 300lb rear allowed. Mazda tower brace 0000-04-5626 allowed. Mazda header
Show 20 more lines
0000-06-5410 allowed." In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. Up to 500lb front and 300lb rear springs allowed. Mazda Motorsports Header part #0000-06-5410 allowed. Mazda tower brace 0000-04-5626 allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5." In T3 Spec Lines, Mazda MX-5 Miata (16-18), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Header permitted. Cold air intake permitted. Front strut brace permitted. Front and rear sway bars permitted up to 35mm, Springs 800 front and 800 Rear max permitted. Any OEM or aftermarket hardtop permitted that retains the OEM roof silhouette including Mazda hardtop part #0000-07-5902- ND and part #0000-07-5901 (discontinued DG Motorsports top). If a hardtop is used, latches shall be replaced with positive fasteners. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, change Notes as follows: "Shoulder harness installation must conform to FIA mounting specifications that are approved for this vehicle per section 6.2 FIA article 253, safety equipment. Must meet all ND2 MX-5 Global Cup rules. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop Mazda hardtop part #0000-07-5902-ND and #0000-07-5902-ND part #0000- 07-5901 (discontinued DG Motorsports). If a hardtop is used, latches shall be replaced with positive fasteners. OBD2 requirement does not apply. Ballast box may be removed. ND2s with sequential gearbox allowed +100 lbs.
unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.
As printed in Fastrack
In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes: "Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."
unclearT3 Ford Mustang EcoBoost loses optional 2-piece 355mm Brembo rotor brake kit option with 50 lb penalty.
As printed in Fastrack
In T3 Spec Lines, Ford Mustang EcoBoost (2015-), change Notes as follows: ", or optional 2-piece rotor 355mm max Brembo brake kit #M-2300-S allowed with +50lb penalty."
Applies to Ford Mustang on this page: Scotty B White, Roger Eagleton, Matt Lituchy, Michael Lowe, Rick Luckett
fasterT3 BMW Spec E9X tire width increases to 255 from 225; spec E9X tire or any DOT permitted.
As printed in Fastrack
In T3 Spec lines, BMW Spec 9X, change as follows: Car: "BMW Spec 9X BMW Spec E9X" Notes: "Must conform to all SpecE9X rules Version 2.10. Spec E9X spec tire permitted or any DOT permitted up to 225 255 permitted. No other touring allowances permitted. Engines may not be modified unless specified in the Spec E46 rules and must conform to touring tech procedures. Driver must possess a current copy of the rules. Dyno results do not ensure engine compliance. THIS SPEC LINE DOES NOT QUALIFY FOR SCCA RUNOFFS COMPETITION UNTIL IT HAS BEEN REPRESENTED IN 3 SCCA SUPER TOUR EVENTS."
fasterT3 SpecE46 permitted tire width increases from 225 to 245.
As printed in Fastrack
In T3 Spec Lines, BMW SpecE46, change Notes as follows: "Must conform to all SpecE46 rules Version 3.0. SpecE46 spec tire permitted or any DOT permitted up to 225 245 permitted. No other touring allowances permitted. Engines may not be modified unless specified in the Spec E46 rules and must conform to touring tech procedures. Driver must possess a current copy of the rules. Dyno results do not ensure engine compliance. SE46 HP limit does not apply."
T3 Alternate Placement of Fuse Panel and Electronics Request
wordingT2, T3, T4 cars may relocate under-dash electronics and fuse boxes for access after roll cage installation.
As printed in Fastrack
In GCR, Section 9.1.9.2.D.9.d, add the following: "8. Under-dash electronics including computers, modules and fuse boxes may be relocated so they can be easily accessed after roll cage installation."
suspension & brakesPrototype carbon-carbon and carbon-ceramic brake rotors now permitted instead of prohibited.
As printed in Fastrack
In Prototype, GCR section 9.1.8.B.F.2, change as follows: "Brake calipers may be ferrous or aluminum alloy. Effective 1/1/2026, carbon-carbon and carbon-ceramic brake rotors are prohibited and rotors must be ferrous. Brake rotor material is unrestricted."
suspension & brakesT4 Performance now permits 1-piece alternative rotors matching spec line sizes; alternate brake kits allowed same.
As printed in Fastrack
In GCR, Section 9.1.9.2.D.6.a.6., change as follows: "In T2-Performance alternative rotors, including 2 piece rotors are permitted. Rotors must be within 5% of OE diameter or a maximum diameter of 360mm. In T3- Performance alternative rotors, including 2 piece rotors are permitted with a maximum diameter of 360mm. T4- Performance alternative 1-piece rotors are permitted but rotors must meet the sizes listed in the spec line. Spec lines showing alternate brake kits are also permitted to use 1-piece performance alternative rotors of the same size."
unclearFP Fiat X1/9 gains dual carburetor options with 28mm side-draft alternates and revised valve/transmission specs.
As printed in Fastrack
In FP Spec Lines, change as follows: Fiat X-1/9 & Bertone 1300: "(1) Weber 32 DMTR or DATRA/100 w/32mm bores (1) 40 DCNF w/32mm choke(s) (2) auto-type side-draft w/28mm choke(s) on I.R. manifold Orientation of the alternate carburetor is unrestricted. The alternate carb adapter may not be thicker than 1.25”. The adapter may have a bore larger than the throttle bore of the approved alternate carburetor. Valve Size: (I) 35.5/(1.40) (E) 31.3/(1.23)30.5/(1.20) (E) 1.23
Show 10 more lines
Trans. Speeds: 5" Fiat X-1/9 & Bertone: "Fuel Injection (1) 34 DMTR, (1) 36 DCNF w/34mm choke(s), or (1) 40DCNF w/34mm choke(s) (1) 36 or 40 DCNF w/34mm choke(s) (2) auto-type side-draft w/28mm choke(s) on I.R. manifold Orientation of the alternate carburetor is unrestricted. The alternate carb adapter may not be thicker than 1.25”. The adapter may have a bore larger than the throttle bore of the approved alternate carburetor. Valve Size: (I) 35.5/(1.40) (E) 33.0/(1.30) Trans. Speeds: 5 or 4"
fasterT2-T4 adjustable toe links now allow performance alternative bushings and spherical bearings, previously prohibited except in specified examples.
As printed in Fastrack
In GCR, Section 9.1.9.D.5.a.1., change as follows: "T2-T4: A maximum of 3.5 degrees of negative camber is allowed on front and rear suspensions. Spec line part(s) may not be modified to increase caster and camber. Strut suspensions may adjust camber and caster by the use of eccentric bushings, eccentric bolts (crash bolts) at the strut-to-spindle, and/or by use of slotted adjustment plates at the top of the strut mounting plate. If upper strut slotted adjustment plates are used, they shall be located on existing chassis structure, utilizing the unmodified manufacturer’s original bolt holes and may not serve as reinforcement for that structure. Slotted adjustment plates (strut camber plates) may incorporate a single spherical bearing (spherical bushing) and a ball thrust bearing per strut tower. On other forms of suspension, camber and caster adjustment may be achieved by the use of shims and/or eccentric
Show 4 more lines
bushings. Adjustable toe links with spherical bearings are permitted and may serve no purpose other than adjusting toe angle. Adjustable toe links are permitted. They are allowed to have performance alternative bushings and spherical bearings. They may serve no purpose other than adjusting toe angle. Spherical bearings/bushings are not permitted in T2-T4 except for the specific examples listed in the class rules or vehicle spec line."
T1 LS1 into Corvette C6 Spec Line Request
#39716 from Danny Kellermeyerhttps://crbscca.com/secu · Rule change · TB 26-02 (2026-02 Fastrack)
In T1 Spec Lines, reinstate Spec Line # 1139, Chevrolet Corvette C6 (05-13) Includes Z51, GrandSport, Z06, Z06 Carbon, as follows: Max Displ: "LS1, LS6 OEM" Min Weight: "3200" Required Restrictor: "70mm"
What the rules allowed changed as listed; this does not say what any particular car ran.