This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One session is left out because the timing does not look like full laps: Cal Club 2023 Qualifying #2.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
BMW M3
T1
1
1:46.465Ian Barberi
1:46.465Ian Barberi
1:47.434Ian Barberi
114.9Ian Barberi
28.992Ian Barberi
30.811Ian Barberi
46.263Ian Barberi
BMW M4 GT4
T1
1
1:47.084Drew Delmonico
1:47.084Drew Delmonico
1:47.467Drew Delmonico
161.4Drew Delmonico
29.150Drew Delmonico
30.850Drew Delmonico
46.316Drew Delmonico
Swift Db6
FF
2
1:49.259Edward Erlandson
1:55.247Johnnie Crean
1:54.993Johnnie Crean
124.5Johnnie Crean
31.358Johnnie Crean
32.841Johnnie Crean
47.766Edward Erlandson
SWIFT DB-6 Honda
FF
1
1:49.259Edward Erlandson
47.766Edward Erlandson
Swift Db6
FF
1
1:54.993Johnnie Crean
1:55.247Johnnie Crean
1:54.993Johnnie Crean
124.5Johnnie Crean
31.358Johnnie Crean
32.841Johnnie Crean
50.291Johnnie Crean
Piper DL7-Honda
FF
1
1:51.118Eric Poulsen
1:52.044Eric Poulsen
1:51.118Eric Poulsen
114.7Eric Poulsen
30.276Eric Poulsen
31.650Eric Poulsen
48.818Eric Poulsen
SWIFT DB-
FF
1
1:53.098Edward Erlandson
1:53.098Edward Erlandson
1:54.741Edward Erlandson
133.7Edward Erlandson
30.951Edward Erlandson
32.299Edward Erlandson
49.791Edward Erlandson
Mazda MX-5
T4
1
1:58.339Oscar Jackson
1:58.339Oscar Jackson
1:59.922Oscar Jackson
105.5Oscar Jackson
32.394Oscar Jackson
34.071Oscar Jackson
51.874Oscar Jackson
Pontiac GTO
T1
1
1:59.123Ed Gless
1:59.760Ed Gless
1:59.123Ed Gless
120.7Ed Gless
32.383Ed Gless
34.587Ed Gless
51.370Ed Gless
Ford Mustang
T1
1
1:59.261Pratt Cole
1:59.261Pratt Cole
98.6Pratt Cole
32.624Pratt Cole
34.661Pratt Cole
51.577Pratt Cole
Toyota FRS
T4
1
2:01.157Izzy Sanchez
2:01.678Izzy Sanchez
2:01.157Izzy Sanchez
135.5Izzy Sanchez
32.955Izzy Sanchez
34.751Izzy Sanchez
52.742Izzy Sanchez
Scion FR-S
T4
1
2:01.843Tony Kiratsous
2:01.843Tony Kiratsous
2:03.865Tony Kiratsous
133.6Tony Kiratsous
32.895Tony Kiratsous
34.958Tony Kiratsous
53.933Tony Kiratsous
Mazda Miata
T4
2
2:03.007Kristina Etherington
2:03.241Kristina Etherington
2:03.007Kristina Etherington
128.1Kristina Etherington
33.464Kristina Etherington
35.459Kristina Etherington
53.723Kristina Etherington
Porsche Boxster
T4
1
2:05.833Lynne Griffiths
2:05.833Lynne Griffiths
2:07.226Lynne Griffiths
122.0Lynne Griffiths
33.699Lynne Griffiths
36.036Lynne Griffiths
55.879Lynne Griffiths
Mazda RX-8
T4
1
2:05.858Steven Kiratsous
2:06.604Steven Kiratsous
2:05.858Steven Kiratsous
105.7Steven Kiratsous
33.416Steven Kiratsous
35.585Steven Kiratsous
55.885Steven Kiratsous
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
wordingT1 cars with aftermarket sequential transmissions get 10-inch max bellhousing; non-sequential cars gain 100 lbs weight break.
As printed in Fastrack
In GCR, Section 9.1.9.1.I.4., change as follows: "Aftermarket sequential transmissions are permitted. Cars with aftermarket sequential shift transmissions shall utilize a 1:1 (or greater/overdriven) ratio in top gear. Transmission location must be OEM. Maximum bellhousing length is 10 inches. Cars that don’t use an aftermarket sequential transmission may decrease their competition weight by 100 lbs."
FF Add Fast Forward Part Numbers for Honda Fit Engine
wordingFF Honda Fit engine adds Fast Forward part number alternatives for intake, exhaust, oil system, and scavenge pump components.
As printed in Fastrack
In FC/FF, GCR section 9.1.1.B.14.a.6, change as follows: "For all Honda part numbers in these specifications, superc seding part numbers are considered equivalent. In FC/FF, GCR section 9.1.1.B.14.f.5, change as follows: "Cylinder head breather restrictor must be used as supplied by HPD or Fast Forward, unmodified.: HPD PN: 15262-F21S-A200; Fast Forward PN: FF200-503." In FC/FF, GCR section 9.1.1.B.14.k.2, change as follows: "The upper manifold, air box and throttle body assembly must be used as delivered from Honda, HPD, or Fast Forward as noted below."
Show 35 more lines
In FC/FF, GCR section 9.1.1.B.14.k.2, insert as follows: "a. Intake manifold: HPD PN: 17210-F21S-A210; Fast Forward PN: FF200-201. b. Throttle body: Honda Fit: PN: 16400ZZ5024; HPD PN: 16400ZZ5024; Fast Forward PN: FF200-104. c. Throttle lever: HPD PN: 17330-F21S-A210; Fast Forward PN: FF200-101." In FC/FF, GCR section 9.1.1.B.14.k.3, change as follows: "All gaskets and sensors utilized on the inlet manifold from head to throttle body must be Honda Fit OEM, or HPD supplied or Fast Forward as noted below. a. Gasket In. manifold: HPD PN: 17105-RB0-004, Honda Fit OEM. b. Gasket, EGR chamber cover: HPD PN: 17146-RB0-004, Honda Fit OEM. c. Gasket In. port: HPD PN: 17115-RB0-007, Honda Fit OEM. d. Gasket, restrictor: HPD PN: 17399-F21S-A200, (2 required) HPD; Fast Forward PN: FF200-109. Two required." In FC/FF, GCR section 9.1.1.B.14.k.5, change as follows: "The Honda Fit engine is required to have an HPD supplied air inlet restrictor supplied by HPD or Fast Forward: HPD PN: 17344- F21S-A201; Fast Forward PN: FF200-110, with internal diameter of 30.5mm and thickness of 3.175mm (0.125 inches) correctly installed within the intake system." In FC/FF, GCR section 9.1.1.B.14.m.1, change as follows: "The exhaust manifold must be as supplied by HPD or Fast Forward:, HPD part # PN: 18150-F21S-A200 or # PN: 1818 50-F21S-B200; Fast Forward PN: FF500-001 or PN: FF500-002." In FC/FF, GCR section 9.1.1.B.14.n.1, change as follows: "The oil pan, baffle plate, and scavenge pump filter fittings must be as supplied by HP or Fast Forward as noted below. No modifications are permitted. a. Oil pan: HPD PN: 11200-F21S-A210 or PN: 11200-F21S-C240; Fast Forward PN: FF100-201A or PN: FF100-201B. b. Oil pan baffle plate: HPD PN: 11221-F21S-A210; Fast Forward PN: FF100-202. c. Oil scavenge pump filter fittings (2 required): HPD PN: 15180-F21S-A210; Fast Forward PN: FF100-204." In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows: "The scavenge pump and internal scavenge pump parts must be as supplied from HPD or Fast Forward as noted below." In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows: "b. Rotor outside diameter: HPD 44.400mm (1.748 inches):; Fast Forward 40.640mm (1.600 inches). c. Scavenge pump rotor set: HPD PN: 15450-F21S-A20; Fast Forward PN: FF100-110. d. Oil pump: HPD PN: 15100-F21S-A200; Fast Forward PN: FF100-100A. e. Scavenge pump cartridge: 15111-F21S-A21; Fast Forward PN: FF100-127. f. Scavenge pump port A: HPD PN: 15137-F21S-A20; Fast Forward PN: FF100-101. g. Scavenge pump port B: HPD PN: 15139-F21S-A20; Fast Forward PN: FF100-102. h. Scavenge pump shaft: HPD PN: 15510-F21S-A20; Fast Forward PN: FF100-103. i. Scavenge pump front cover: HPD PN: 15070-F21S-A21; Fast Forward PN: FF100-104."
wordingT1 GT4 weights clarified for nine cars, ranging from 3200 lbs Porsche 718 Cayman to 3575 lbs Aston Martin.
As printed in Fastrack
RM 23-04 – Touring 1 weights dated 3/21/2023 As an E&O to the February Fastrack, in T1-GT4 leave weights as follows: Aston Martin Vantage AMR GT4: 3575 Audi R8 GT4: 3550 BMW M4 GT4: 3500 Ford Mustang GT4: 3550 Maclaren 570S GT4: 3450 Mercedes AMG GT4: 3450
Show 3 more lines
Porsche 718 Cayman GT4 CS MR: 3200 Porsche 718 GT4 RS Clubsport: 3450 Toyota Supra GR GT4: 3350
fasterT4 Mini Cooper S all years now run 17-inch wheels, up from 16, with wider rims to 8 inches.
As printed in Fastrack
In T4 Spec Lines, Mini Cooper S (02-04), change as follows: Wheel Size: "16 x 7 17 x 8" Add to Notes: "Wheels conforming to B-spec rules are permitted." In T4 Spec Lines, Mini Cooper S (05-06), change as follows: Wheel Size: "16 x 7 17 x 8" Add to Notes: "Wheels conforming to B-spec rules are permitted." In T4 Spec Lines, Mini Cooper S (07-13), change as follows: Wheel Size: "17 x 7 8"
fasterT4 Audi A4 2.8 V6 wheels grow to 17x8, tyres to 245, springs now 800lb with 32mm sway bars.
As printed in Fastrack
In T4 Spec Lines, Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05), change as follows: Wheel Size: "16 x 7 17 x 8" Tire Size: "225 245" Notes: "The following items must remain stock: shock/struts (including mounts), original wheels, and transmission differential - unless specified below. 800lb springs allowed. Front and rear sway bars permitted 32mm max."
slowerT1 Chevrolet Camaro Gen 5, Corvette C5 and C6: engine resleeve restricted to stock parameters only, no longer LS3 bore/stroke.
As printed in Fastrack
In T1 NEW Spec Lines, Chevrolet Camaro Gen 5 (10-15) Including SS, Z28, change Engine Notes as follows: 1130: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1135: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement.May resleeve to stock parameters for engine repair or replacement." In T1 NEW Spec Lines, Chevrolet Corvette C5 (‘97-’04) – Includes: Z06, Coupe, Convertible, change Engine Notes as follows: 1132: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement."
Show 18 more lines
1134: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1136: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1138: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." In T1 NEW Spec Lines, Chevrolet Corvette C6 (05-13) - Includes Z51, GrandSport, Z06, Z06 Carbon, change Engine Notes as follows: 1150: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1160: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1170: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1180: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1190: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement."
fasterT4 Mini Cooper S R53 loses 50 lbs, to 2700 for both 02-04 and 05-06 model years.
As printed in Fastrack
In T4 Spec Lines, Mini Cooper S (02-04), change Weight as follows: "2750 2700" In T4 Spec Lines, Mini Cooper S (05-06), change Weight as follows: "2750 2700"
fasterT1 Corvette C5 gains approved aero parts: carbon rear spoiler, vented front splitter, side skirts, with 50 lb weight reduction allowed.
As printed in Fastrack
In T1 NEW Spec Lines, Chevrolet Corvette C5 (‘97-’04) – Includes: Z06, Coupe, Convertible, Spec Lines 1132-1138, add to Notes as follows: "Any option of OEM Bodywork parts may be used as basis for aero measurements. Rear spoiler max 5” Above bumper allowed. +50lbs. The following parts are permitted, with a 50lb decrease from base weight, in lieu of the aero options permitted in 9.1.9.1.B: (C7Carbon Rear- Spoiler CCC5 EX- RSB-GB, Vented Front Splitter CCC5-FS-GB, Side Skirts CCC5 SS-GB.)"
wordingT3 Mazda RX-8 removes transmission/final drive pairing requirement; T4 removes same requirement, adds Mazdaspeed radiator and coil spring kit.
As printed in Fastrack
In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows: "Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3 transmission must be paired with the listed alternate final drive. Front sway bar permitted 32mm MAX rear sway bar 19 MAX, Front springs max 750, 500 rear. Cold air intake permitted. Header permitted. Aftermarket flywheel and single disc clutch permitted with no weight penalty." In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows: "Mazdaspeed radiator #0000-01-8501 allowed. Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3 transmission must be paired with the listed alternate final drive. Mazdaspeed coil spring kit #QSEA-34-01Z allowed. 60mm flat plate restrictor required. OE Rear spoiler allowed #F151-V4-920F. OE front air dam allowed #F151-V4-900f-BB. Springs Allowed:
Show 2 more lines
(F) Mazda Motorsports- 0000- 04-9700-08 or Eibach- 0800.250.0700 (R) Mazda Motorsports- 0000-04-9400-07 or Eibach 0700.250.0400, and helper 0000-04-9926 allowed. Alternate sway bars allowed max 32mm (f) 19mm (r)."
fasterT3 BMW 320i (14-15) gains aftermarket intercooler permission; T4 loses it.
As printed in Fastrack
In T3 Spec Lines, BMW 320i (14-15), add to Notes the following: "Aftermarket intercooler permitted." In T4 Spec Lines, BMW 320i (14-15), remove from Notes the following: "Aftermarket intercooler permitted."
T1 Request to Remove Expiration from T1 spec lines #1350 & #1370
wordingT1 Dodge Viper ACR / SRT RT-10 and ACR/ACR-X spec lines 1350 and 1370 remove 12/23 expiration.
As printed in Fastrack
In T1 NEW Spec Lines, Dodge Viper ACR / SRT RT-10, change Spec Line Number as follows: "1350 *Spec line Expires 12/23*" In T1 NEW Spec Lines, Dodge Viper ACR/ACR-X, change Spec Line Number as follows: "1370 *Spec line Expires 12/23*"
wordingT3 Pontiac Solstice GXP minimum ride height set to 3 inches.
As printed in Fastrack
In T2 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following: "Minimum ride height is 3 inches." In T3 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following: "Minimum ride height is 3 inches."
cars addedT1 Porsche 997-1 GT3 Cup added at spec line 4210, minimum weight 3050 lbs.
As printed in Fastrack
In T1 Spec Lines, delete the Porsche 996 GT3 Cup car from the standard spec lines and classify "Homologated car" section as follows: T1 – Homologated Cars
A specification table follows in the original; it is not shown here.
slowerT4 Mazda MX-5 ND1 minimum weight increases 50 lbs to 2700; suspension springs now allow up to 500 lb front, 300 lb rear.
As printed in Fastrack
In T4 Spec Lines, Mazda MX-5 Miata/Club/ RF (16-18), change as follows: Weight: "2650 2700" Notes: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must remain stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs #0000-04-9700-08, rear springs #0000-04-9400-07, helper springs #0000-04-HLPR-EB (optional). Up to 500lb front and 300lb rear
unclearT1-GT4 batch adjustments: five cars lighter, two heavier, restrictors and ECU maps changed, five models now eligible for Runoffs.
As printed in Fastrack
In GCR, Section 9.1.9.1.A.T., change as follows: "Tires- Tires must conform to GCR section 9.3.TIRES and als o must conform to spec line requirements. DOT approved tires are permitted. Slicks conforming to the spec line are permitted." In Touring 1 - Homologated Cars Spec Lines, 4100- BMW M2 ClubSport Racing, change Must Conform To as follows: "Tires conforming to SRO TCX rules allowed. Must meet factory specs." In Touring 1 - Homologated Cars Spec Lines, 4120- Ford Mustang FP350S 2017, change as follows: Must Conform To: "Tires conforming to Trans Am SGT tire rules allowed Must meet factory specs." Chassis Notes: "VIN not required. Additional permitted allowances: DOT tires required. Other consumables are open, alternate
Show 40 more lines
driveshaft permitted, aftermarket wheels and fuel cell per Touring category rules permitted. Shocks conforming to T1 rules permitted. Alternative rear toe links permitted." In T1-GT4 Spec Lines, change Chassis Notes as follows: Aston Martin Vantage AMR GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)** Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Audi R8 GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." BMW M4 GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Chevrolet Camaro GT4-R: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Ford Mustang GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Maclaren 570S GT4: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Mercedes AMG GT4: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Porsche 718 Cayman GT4 CS MR: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Porsche 718 GT4 RS Club-sport: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Toyota Supra GR GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." In T1-GT4 Spec Lines, change as follows: Aston Martin Vantage AMR GT4: Weight: “3575 3490” Performance Control: “SRO power level ECU Map 3 IMSA Map id 11” Chevrolet Camaro GT4-R: Weight: “3375 3435” Performance Control: “63 62mm” Ford Mustang GT4: Weight: “3550 3535” Performance Control: “63 71mm SRO compliant restrictor IMSA ECU Cal” Maclaren 570S GT4: Weight: “3450 3250” Performance Control: “SRO 2019 BOP ECU map SRO Rest 1” Mercedes AMG GT4: Weight: “3450 3470” Performance Control: “Power level 2 map 5” Porsche 718 Cayman GT4 CS MR: Weight: “3200 3250” Performance Control: “54 53.7mm” Toyota Supra GR GT4: Weight: “3350 3315”
wordingFF Honda Fit gains Fast Forward FF800-100 oversize piston ring pack option.
As printed in Fastrack
In FF, GCR section 9.1.1.B.14.e.3.a, add the following: "The standard ring pack, PN 13011-RB1-004 (Riken) or 13011-RB1-006 (Nippon), or the oversize ring pack, PN 13021-RB7-Z01 (Riken), or 13021-RB7-Z02 (Nippon), or FF800-100 (Fast Forward), may be used."
In GCR, Section 9.1.9.2.D.1.g.3., change as follows: "Batteries may be replaced provided the replacement is capable of starting the car. Batteries may not be relocated unless noted on the spec line. Batteries must be adequately secured. Battery labeling must conform to 9.3.35.D. with those of an alternate manufacturer, provided they are of similar amp-hour capacity, size and within 10% of OEM weight."
wordingT4 Mazda MX-5 Miata/Club (16-18) and (19-21) permitted to replace 3rd and 4th gears with specific parts.
As printed in Fastrack
In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), add to Notes the following: "3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804- 02, 0000-02-5804-01)." In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-21), add to Notes the following: "3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804- 02, 0000-02-5804-01)."
Applies to Mazda MX-5 on this page: Oscar Jackson
Applies to Mazda Miata on this page: Kristina Etherington, Kayla Etherington
cars addedT4 now permits C-Spec cars to compete alongside B-Spec cars.
As printed in Fastrack
In GCR, Section 9.1.9.2., change as follows: "Touring car eligibility: Cars are eligible for the class they are listed with a specification line and with the specific allowances permitted. In addition, T2-T4 cars may race one class up in touring classes above their specification line class as long as they are a legal T2-T4 car and conform to their specification line allowances as classified. Cars conforming to C-Spec rules are permitted to compete in Touring 4."
wordingT2-T4 spec lines for 46 cars expire 12/31/24; appeal required to continue.
As printed in Fastrack
In T2-T4 Spec Lines, add **This Spec line will expire 12/31/24, Please submit to appeal** to Notes to the following Spec Lines: T2: Acura TL SHAWD (10-13) Audi S4 (12-14) Audi S5 (13-14) Audi TT RS (2018-) Cadillac ATS-V (16-17)
Show 46 more lines
Cadillac CTS-V (06-07) Chevrolet Camaro SS (98-02) Honda Civic (2017-) Saturn Sky / Convertible (07-09) Subaru Impreza WRX STi (03-07) Subaru Impreza WRX STi (08-11) T3: Audi S4 (10-11) Audi S4 (12-14) Audi TTS Coupe (10-11) Cadillac ATS (2015) Chevrolet Cobalt (05-07) Dodge SRT-4 (03-05) Ford Fiesta ST (2014-) Hyundai Genesis Coupe (2010-) Hyundai Veloster Turbo (18-21) Mazda RX-8 Base/R3/Sport/ GT (04-12) Mini Cooper S (2016-) Subaru WRX (02-05) Toyota Camry (11-15) T4: Acura Integra GS-R VTEC (3 or 4 door) (94-01) Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05) BMW 320i (14-15) Chevrolet Cobalt SS, Sport Coupe (06-10) Chevrolet Sonic RS (2011-) Chrysler/Dodge Neon ACR SOHC (4 door) (01-02) Dodge Dart (14-15) Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99) Fiat 500 Abarth (12-14) Ford Focus SVT (02-04) Ford Focus ZX4 ST (05-06) Ford Focus (08-11) Ford Mustang V-6 (01-04) Honda Accord LX & EX (03-07) Honda Accord LX-S/EX/EX-L (08-12) Honda Civic Coupe Si (99-00) Honda Civic SI (02-03) Hyundai Elantra GLS (11-12) Hyundai Tiburon V-6 (03-08) Hyundai Veloster Turbo/ R-Spec (14-15) Kia Forte Koup and Sedan LX/EX (10-13) Kia Forte Koup and Sedan SX (10-13) Kia Forte Koup (14-15) Mazda Protégé ES (2000) Mazda Protégé 5 (02-03)
removedT1 NEW class removes 23 spec lines including Acura NSX, Ferrari, Porsche 996, Nissan Z cars, and others; Porsche 997 spec line 1680 expiration removed.
As printed in Fastrack
In GCR Contents, change as follows: "9.1.9.1 TOURING (T1) CATEGORY NEW T1 NEW" In GCR, Section 9.1.9.1.Touring (T1) NEW Category Specifications, change as follows: "9.1.9.1.Touring (T1) NEW Category Specifications" In T1 NEW Spec Lines, change as follows: "9.1.9.1.A T1 NEW Spec Lines" "T1 NEW"
Show 26 more lines
In T1 NEW Spec Lines, delete the following Spec Lines in their entirety: "Acura NSX (Spec Line 1000) Acura NSX Turbo (Spec Line 1010) Acura NSX Turbo World Challenge (Spec Line 1020) Audi TTRS (GTS 2011 Spec) (Spec Line 1040) Dodge Viper ACR/ACR-X (Spec Line 1360) Ferrari 360 (Spec Line 1400) Ferrari 430 (Spec Line 1410) Ferrari 430 Challenge (Spec Line 1420) Mazda MX-5 (06-15) (Spec Line 1520 and 1530) Mazda RX-7 (Spec Line 1540) Nissan GTR (Spec Line 1550) Nissan 350/370Z (Spec Line 1560) Nissan 370Z Supercharged (Spec Line 1570) Nissan 350Z (Spec Line 1580) Nissan 350Z/370Z (Spec Line 1590) Porsche Cayman/S/GTS (05-15) (Spec Line 1600, 1610 and 1620) Porsche Cayman GTS (2011) (Spec Line 1630) Porsche 928 S4 Porsche 928 GTS-R (Spec Line 1640) Porsche 996 (Spec Line 1650) Porsche 996 TT OEM (Spec Line 1660) Subaru WRX, WRX STI (05-2020) (Spec Line 1700) Toyota Celica All-Trac (Spec Line 1710) Toyota Supra MK4 (Spec Line 1720)" In T1 NEW Spec Lines, Porsche 997, change Spec Line Number as follows: "1680 *Spec line Expires 12/23*"
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
wordingT4 Mazda RX-8 allows Mazdaspeed radiator, coil spring kit, OE rear spoiler, front air dam, springs to 700 lb front/400 lb rear, oil metering pump bypass, sway bars to 32 mm front/19 mm rear.
As printed in Fastrack
In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change Notes as follows: "Mazdaspeed radiator #0000-01-8501 allowed. Mazdaspeed coil spring kit #QSEA-34-01Z allowed. OE Rear spoiler allowed #F151-V4-920F. OE front air dam allowed #F151-V4-900f-BB. Springs allowed 700lb (f) max, 400(r) max. Oil metering pump may be bypassed. Alternate sway bars allowed max 32mm (f) 19mm (r)."
T4 Allow T4 and T3 RX8 to Disable/Remove Factory Oil Inj.
unclearT3 and T4 Mazda RX-8 may remove or disable factory oil injection system.
As printed in Fastrack
In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows: "OEM oil injection system may be removed or disabled." In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows: "OEM oil injection system may be removed or disabled."
slowerT4 Mazda MX5 Miata/Club/RF year range extended to 2024, suspension package permitted with 100 lbs weight increase.
As printed in Fastrack
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-21), change Year as follows: "(19-21 24)" In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-21), add to Notes as follows: "Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs #0000-04-9700- 08, springs up to 500lb front and 300lb rear allowed. Mazda tower brace 0000-04-5626 allowed."
slowerT2, T3, T4 driveshafts may use alternative materials or one-piece units; non-OEM adds 25 lbs.
As printed in Fastrack
In GCR Section 9.1.9.2.D.4.b., add the following: "6. T2-T3- Driveshafts may be replaced with alternative materials ie. carbon fiber, aluminum, steel. Two-piece driveshafts may be replaced with one-piece units. If non-OEM driveshaft is used, add 25 lbs."
fasterT4 Mazda MX-5 Miata/Club 16-18 removes differential stock requirement, allows up to 500lb front and 300lb rear springs.
As printed in Fastrack
In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must remain stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs #0000- 04-9700-08, rear springs #0000-04-9400-07, helper springs #0000-04-HLPR-EB (optional). Up to 500lb front and 300lb rear springs allowed. Mazda Motorsports Header part #0000-06-5410 allowed. Mazda tower brace 0000-04-5626 allowed."
Applies to Mazda MX-5 on this page: Oscar Jackson
Applies to Mazda Miata on this page: Kristina Etherington, Kayla Etherington
fasterT4 Mini Cooper S 02-04 and 05-06 now allow Milltek exhaust manifold #SSXM459 and 25mm rear sway bar.
As printed in Fastrack
T4 Spec Lines, Mini Cooper S (02-04), add to Notes the following: "Milltek exhaust manifold #SSXM459 allowed. 25mm rear sway bar allowed." T4 Spec Lines, Mini Cooper S (05-06), add to Notes the following: "Milltek exhaust manifold #SSXM459 allowed. 25mm rear sway bar allowed."
unclearFord Mustang GT 5.0L and V6 now permit Track/Performance Package parts in T2 and T3.
As printed in Fastrack
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes as follows: "Track/Performance Package parts permitted." In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows: "Track/Performance Package parts permitted." In T3 Spec Lines, Ford Mustang V6 (15-17), change Notes as follows: "Track/Performance package allowed."
fasterT2-T4 Ford Mustangs: remove 25 lbs penalty for non-OEM driveshaft, clarify alternate driveshaft allowances.
As printed in Fastrack
In GCR Section 9.1.9.2.D.4.b.6., remove as follows: "If non-OEM driveshaft is used, add 25 lbs." In T2 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows: "Driveshaft from Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang Boss 302 (12-13), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang GT 5.0L (11-14)ki, change Notes as follows: "Alternate metallic driveshaft is allowed."
Show 12 more lines
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), change Notes as follows: "Alternate metallic driveshaft is allowed." In T2 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L (05-10), change Notes as follows: 'An Aluminum driveshaft is allowed." "Alternate metallic driveshaft is allowed." In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), change Notes as follows: "An Aluminum driveshaft is allowed." "Alternate metallic driveshaft is allowed." In T3 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows: "Driveshaft from Alternate metallic driveshaft is allowed."
wordingT4 Mini Cooper S (02-04) deleted; (05-06) model year corrected to R53; (07-13) R56 simplified specs; (2014-2023) added with spring rates.
As printed in Fastrack
In T4 Spec Lines, Mini Cooper S (02-04), delete spec line in its entirety. In T4 Spec Lines, Mini Cooper S (05-06), change Model as follows: "Mini Cooper S R53 (0205-06)" In T4 Spec Lines, Mini Cooper S (07-13), change Model and Notes as follows: "Mini Cooper S R56 (07-13)" Notes: "The following items must remain stock: shock/struts (including mounts), original wheels, and transmission differential - unless specified below. Convertible model not allowed. Factory optional limited slip differential allowed. JCW struts (F) 31 31 6 768 410 (R)33 52 6 768 412, springs (F)31 33 6 768 415 (R)33 53 6 768 418. May de-camber
Show 8 more lines
wheels by the use of slotted adjusters at the top of the strut mounting plates. They shall be located on the existing chassis structure, utilizing the manufacturers original bolt holes and may not serve as reinforcement for that structure. Any spring up to a maximum spring rate of 500 lbs. front and 800 lbs. rear may be used. Wheels conforming to B-spec rules are permitted." In T4 Spec Lines, Mini Cooper S (2016-), change Model and add to Notes as follows: "Mini Cooper S (20142016-2023)" Notes: "Convertible model not allowed. Any spring up to a maximum spring rate of 500lbs. front and 800lbs. rear may be used."
fasterT4 OEM intake chambers, resonators and acoustic devices may be removed if ports sealed and before restrictor.
As printed in Fastrack
In GCR Section 9.1.9.2.D.1.b., add the following: "2. OEM intake- Chambers, resonators and acoustic devices may be removed, provided; that their ports are located prior to any required restrictor, their ports are completely sealed, and that the part serves no other purpose."
wordingFF VTEC activation valve must function; EGR blanking plate rule clarified with Fast Forward part numbers.
As printed in Fastrack
In FF, GCR section 9.1.1.B.14.r.1, change as follows: "All emission control devices must be removed and blocked off by the blanking plate provided by HPD or Fast Forward as noted below, except for the VTEC activation valve. The VTEC activation valve must be retained; and it must be functioning. No modifications are permitted. a. EGR Plate: Fast Forward PN: FF200-301. b. EGR Port Cover: Fast Forward PN: FF200-302."
fasterFF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs.
As printed in Fastrack
In FF, GCR section 9.1.1.B.20.A.3, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight." In FC, GCR section 9.1.1.B.20.B.4, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
wordingFF Honda Fit allows Fast Forward 0.25mm oversize pistons PN FF800-110 as alternative; piston diameter spec clarified to 2.8835 inches.
As printed in Fastrack
In FF, GCR section 9.1.1.B.14.e.1, change as follows: "Honda Fit OEM standard size pistons, PN: 13010-RB1-000, or Honda Fit OEM 0.25mm oversize pistons, PN: 13020-RB7-Z00, or Fast Forward 0.25mm oversize pistons, PN: FF800-110, may be used." In GCR section 9.1.1.B.14.e.2, change as follows: "a. Maximum standard piston diameter, measured at a point 16mm from the bottom of the skirt: 73.240mm (2.8834 2.8835 inches). b. Centerline of wrist pin to crown maximum: 26.21mm (1.032 inches). c. Maximum overall height from skirt to crown edge: 47.80mm (1.882 inches).
Show 13 more lines
d. Minimum weight: 198.0 grams (6.984 ounces). e. Minimum weight of piston pin: 66 grams (2.25 ounces). f. Combined minimum weight of piston, piston pin and connecting rod: 543.5 grams (18.85 ounces). g. Combined minimum weight of piston, wrist pin, and circlips: 267 grams (9.418 ounces). h. Centerline of wrist pin to crown edge: 26.289mm (1.035 inches). i. Ring groove widths: Top ring groove: 1.003mm (0.0395 inches). Middle ring groove: 1.016mm (0.0400 inches). Oil ring groove: 1.981mm (0.0780 inches). j. Ring groove distance from wrist pin center to bottom of groove: Top ring groove: 19.63mm (0.7730 inches). Middle ring groove: 15.29mm (0.6020 inches). Oil ring groove: 10.91mm (0.4295 inches)."
cars addedBMW M4 GT4 (G82) added to T1 GT4 at 3525 lbs minimum weight with Red power stick control.
As printed in Fastrack
In T1 GT4 Spec Lines, SL#4030, change as follows: Model: "BMW M4 GT4 (F82)" Performance Control: "Gold power stick Red power stick" In T1 GT4 Spec Lines, classify BMW M4 GT4 (G82) as follows:
A specification table follows in the original; it is not shown here.
T4 Redundant Verbiage Regarding Mustang Spec Lines for Driveshaft
wordingT2 and T3 Mustang spec lines remove redundant driveshaft alternate/aluminum allowance wording.
As printed in Fastrack
In T2 Spec Lines, change Notes as follows: Ford Mustang V6 (11-14): "Alternate driveshaft is allowed." Ford Mustang Boss 302 (12-13): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (11-14): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (15-17): "Alternate driveshaft is allowed." Ford Mustang GT 5.0L (2018-): "Alternate driveshaft is allowed. Springs up to 800#/in front and rear permitted. Alternate metallic driveshaft permitted." Ford Mustang Coupe GT & Shelby GT 4.6L (05-10): "Alternate driveshaft is allowed."
Show 4 more lines
In T3 Spec Lines, change Notes as follows: Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10): "Alternate driveshaft is allowed." Ford Mustang V6 (11-14): "Alternate driveshaft is allowed." Ford Mustang V6 (05-10): "An Aluminum driveshaft is allowed."
fasterT1 GT4 Spec Line 4020 restrictor opens from 44mm to 45mm, minimum weight drops to 3400 lbs.
As printed in Fastrack
In T1 GT4 Spec Lines, Spec Line 4020, change as follows: Performance Control: Power level 2020, 44mm 45mm SRO compliant restrictor" Min. Weight with driver (LBS): "3550 3400"
wordingT4 removes restriction on aftermarket wheel weight minimum of 15 lbs.
As printed in Fastrack
In GCR Section 9.1.9.2.D.7. Wheels and Tires, change as follows: "a. Wheels 1. Any type wheel suitable for competition may be used, provided: a. Any wheel not exceeding the specified diameter and rim width on the vehicle’s specification line may be used. Each wheel, measured without weights, must weigh at least 15 lbs. b. Wheels are permitted any offset provided the tire tread (that portion of the tire that contacts the ground) does not protrude beyond the fender opening when viewed from 9.1.9.2.Touring (T2-T4) Category Specifications GCR - 660 the top perpendicular to the ground, unless specified differently on the individual spec line for that car. To determine compliance the vehicle should be
Show 7 more lines
rolled through a powdered substance, as raced with driver, in order to indicate the tire tread contact patch under static conditions. When a maximum tire size is listed on a vehicle’s specification line, aspect ratio is open and any tire may be used that does not exceed the stated maximum section width. c. Cars equipped with lug bolts may convert to wheel studs and lug nuts. d. Wheel studs may be replaced with longer studs as necessary to fit optional wheels. Wheel spacers may be used for purposes of adjusting track. e-T4 only: (unless specified on spec line) Any aftermarket wheel with a minimum weight of 15 lbs allowed."
wordingT2, T3, T4 fuel cell installations may remove charcoal canisters, emissions valves, and sensors.
As printed in Fastrack
In GCR, Section 9.1.9.2.D.1.c. add the following: "5. Removal of ancillary fuel tank equipment charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket fuel cell installations."
wordingT2, T3, T4 brake component wording clarified: 2-piece rotors allowed in T2 within 5% OE diameter, T3 within 2% OEM diameter.
As printed in Fastrack
In GCR, Section, 9.1.9.2.D.6. Brakes, change as follows: "a. Components 1. The make and material of brake pads and linings may be changed. 2. Brake fluid may be substituted with any brake fluid. 3. Brake rotor dust shields may be removed or replaced to accommodate brake ducts. 4. Flexible rubber brake lines may be replaced with Teflon lined, metal braided hoses. 5. Any brake ducts are permitted, but they must serve no other purpose. Fender liners may be modified solely for routing and attachment of brake ducts. Duct intake openings may be created by the opening of 2 sections up to 14.5 square inches each in
Show 10 more lines
the front fascia. The stock headlamp location is not permitted for brake ducting. Two alternative duct openings may be created by the removal of the fog lights or 2 sections up to 14.5 square inches each of stock false grills originally located in the front fascia. 6. Stock replacement brake rotors may be obtained from sources other than the manufacturer provided they are the exact equivalent of the stock rotors. In T2 only - 2-piece rotors with ferrous metal rotor disks and aluminum hats are allowed, must be within 5% of OE diameter. In T3 only - 2-piece front rotors with ferrous metal rotor disks and aluminum hats are allowed, must be within 2% of OEM diameter. Drilled and slotted rotors are permitted. 7. Parking brakes, mechanisms, and actuating components may be removed. 8. Brake vacuum reservoirs sized 0.50 gallons or smaller are permitted. The port or fitting at the vacuum source may not be modified, enlarged or relocated. The vacuum reservoir and brake booster must be a closed system."
wordingT2, T3, T4 fuel cell cars may remove charcoal canisters, emissions valves, and sensors.
As printed in Fastrack
In GCR, Section, 9.1.9.2.D.1.c., add the following: "5. Removal of ancillary fuel tank equipment; charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket fuel cell installations."
wordingT3 and T4 Mazda RX-8 and MX-5 permit transmission kit #0000-02-5700.
As printed in Fastrack
In T4 Spec Lines, add the following to Notes: Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted. Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted." In T3 Spec Lines, add the following to Notes: Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted." Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted."
wordingT1 Corvette may roll or flatten wheel opening lips for tire clearance; plastic fenders may remove lips if edge thickness matches basic material.
As printed in Fastrack
In GCR, Section 9.1.9.1.A.2,, add the following: "It is permitted to roll under or flatten any interior lip on the wheel opening for tire clearance. Cars with plastic/composite fenders may remove any interior wheel opening lip, but the resulting material edge shall be no thinner than the basic fender material thickness. Non-metallic inner fender liners may be removed. Vents may be added to fenders."
wordingT4 BMW 320i 14-15 Spec Line expires 12/31/24 removed; Turner Motorsports intercooler #024703TMS02 allowed.
As printed in Fastrack
In T4 Spec Lines, BMW 320i (14-15), change Notes as follows: "**This Spec line will expire 12/31/24, Please submit to appeal** Turner Motorsports intercooler #024703TMS02 allowed."
fasterT4 Honda Civic Si 06-11 minimum weight drops 50 lbs to 2900, restrictor clarified.
As printed in Fastrack
In T4 Spec Lines, Honda Civic Si (06-11), change as follows: Required Restrictor: "55mm flat plate restrictor required." Min Weight: "2950 2900" Notes: "The following items must remain stock: transmission differential - unless specified below. 55mm flat plate restrictor required. LSD IS PERMITTED ACCORDING TO CATEGORY RULES"
T1 Increased Bore Throttle Bodies for E46 M3 S54 Engine
wordingT4 NC MX-5 06-15 removes SM5 suspension allowance, clarifies Mazda Motorsports LSD part number, adds weight penalty for other LSDs.
As printed in Fastrack
In T4 Spec Lines, Mazda MX-5 / Club Model (06-15), change Notes as follows: "Factory bolt-in roll bar/cross member may be removed to facilitate roll cage installation. MSR option permitted. Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front spring mount PT#-0000-04-5259, front springs #0000-04-9700-08, rear spring mount PT#-0000-04-5258, rear springs #0000-04-9400-07, helper springs #0000-04-HLPR- EB (optional), Swaybar kit – PT#-0000-04-5306-EB that includes (front sway bar kit PT#0000-04- 5306-FT, rear sway bar kit PT#- 0000-04-5306-RR), offset front camber bushing PT#-0000-04- 5407-NC. Mazda Motorsports cold air intake part #0000-06-5150- KT allowed. Mazda Motorsport RX8 rear Hub Conversion kit part number 0000-04-5811-KT allowed, RX8 front hubs PT# F189-33- 04X allowed. The SM5 suspension (only) is allowed with a 100 lbs. weight increase. Allow Mazda header part numbers 0000-06-
Show 4 more lines
5407 or 0000-06-5407-NC. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop and part #0000-07-5901- CC. Aftermarket power steering reservoir is allowed. Mazda Transmission kit part # 0000-02- 5700. Mazda Motorsports LSD #3265 5 0000-02-5564 permitted without penalty. Any other non-OEM limited slip differential allowed with +50 lbs. weight penalty. Front spoiler permitted (NF51-V4-900F)."
In T2, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Acura TL SHAWD (10-13) Audi S4 (12-14) Audi S5 (13-14) Audi TT RS (2018-) Cadillac ATS-V (16-17) Cadillac CTS-V (06-07) Chevrolet Camaro SS (98-02)
Show 49 more lines
Honda Civic Type-R (2017-) Saturn Sky / Convertible (07-09)" In T3, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Audi TTS Coupe (10-11) Cadillac ATS (2015) Chevrolet Cobalt (05-07) Dodge SRT-4 (03-05) Ford Fiesta ST (2014-) Hyundai Genesis Coupe (2010-) Hyundai Veloster Turbo (18-21) Mini Cooper S (2016-) Toyota Camry (11-15)" In T4, Effective 1/1/2025, delete for following Spec Lines in their entirety: "Acura Integra GS-R VTEC (3 or 4 door) (94-01) Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05) Chevrolet Cobalt SS, Sport Coupe (06-10) Chevrolet Sonic RS (2011-) Chrysler/Dodge Neon ACR SOHC (4 door) (01-02) Dodge Dart (14-15) Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99) Fiat 500 Abarth (12-14) Ford Focus SVT (02.5-04) Ford Focus ZX4 ST (05-06) Ford Focus (08-11) Ford Mustang V-6 (01-04) Honda Accord LX & EX (03-07) Honda Accord LX-S/EX/EX-L (08-12) Honda Civic Coupe Si (99-00) Honda Civic SI (02-03) Hyundai Elantra GLS (11-12) Hyundai Tiburon V-6 (03-08) Hyundai Veloster Turbo/ R-Spec (14-15) Kia Forte Koup and Sedan LX/EX (10-13) Kia Forte Koup and Sedan SX (10-13 Kia Forte Koup (14-15) Mazda Protégé ES (2000) Mazda Protégé 5 (02-03) Mazda6 s (03-07) Mitsubishi Eclipse GT (00-05) Nissan Sentra SER (02-03) Pontiac Firebird V-6 (96-02) Scion tC (03-07) Subaru Impreza (non-turbo) (04-06) Toyota Celica GT (00-05) Toyota Celica GTS/GT (00-05) Volkswagen Golf TDI (2010) Volkswagen Passat (12-14) Volkswgen Passat TDI (12-14) Volkswgen Passat 1.8T (2014-)"
unclearT1 E46 M3 Spec Line 1050 allows VAC Motorsports throttle body VAC-TB-S54 on 3.250L engine instead of Dinan.
As printed in Fastrack
In T1 Spec Lines, E46 M3 Spec Line # 1050, change Engine Notes as follows: "Dinan Throttle Body #D760-3400 VAC Motorsports #VAC-TB-S54 allowed on the 3.250L."
wordingT4 Ford Mustang V6 (05-14) final drive set to 3.45, GT/CS front bumper cover permitted with front fascia.
As printed in Fastrack
In T4 Spec Lines, Ford Mustang V6 (05-14), change as follows: Final drive: "3.45" Notes: "GT/CS front bumper cover #AR3Z-17D957-BA, allowed if used with front fascia."
T4 Request to Classify Club Spec in Appropriate Touring Classes
unclearT1 Mustang Spec 1430 restrictor opens 60mm to 65mm; Spec 1460 weight rises to 3500 lbs, restrictor 70mm; Corvette 1190 restrictor opens 67mm to 70mm; BMW 1090 restrictor narrows 40mm to 35mm; BMW 1100 weight rises to 3350 lbs.
As printed in Fastrack
In T1 Spec Lines, change Weight, Restrictor Required and/or Notes as follows: Mustang - Spec Line 1430: Restrictor Required: "60mm 65mm - FPR" Mustang - Spec Line 1460: Weight: "3425 3500" Restrictor Required: "70mm - FPR" Corvette Spec Line 1190: Restrictor Required: "67mm 70mm - Flat Plate"
Show 5 more lines
BMW - Spec Line 1090: Required Restrictor: "(2) X 40mm 35mm diameter hole inlet restrictor plate required" Chassis Notes: "This spec line is set to expire 12/31/25." BMW - Spec Line 1100: Minimum Weight: "3150 3350”
FF Formula F Proposal to Invite Older Cars Via a Tire Rule Change
fasterFF allows older cars with rocker arm or outboard suspension to use bias ply slicks or VFF tires instead of radials.
As printed in Fastrack
In FF, GCR section 9.1.1.B.10.e, change as follows: "Formula F shall be limited to the following tires (front tires may not be used as rears): Dries: Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13 Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13 Wets: Front - Hoosier Wet or W3 Radial 44421 185/60R13 Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Show 12 more lines
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at least one chassis end may use the following tires: Dries: Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick Wets: Radial wets listed above or Front - Hoosier 44165 135/545-13 VFF Rear - Hoosier 44170 165/580-13 VFF Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."
fasterT1 Honda S2000 minimum weight reduced from 2950 lbs to 2900 lbs.
As printed in Fastrack
In T1 Spec Lines, Honda S2000, Spec Line 1530, change as follows: Minimum Weight: "2950 2900" Chassis Notes: "This spec line is set to expire as of 12/31/2025 if not represented in Majors competition in 2025."
wordingT1 BMW E46 M3 permits BMW #GS7D36SG aftermarket sequential transmission in SL# 1060 and 1070.
As printed in Fastrack
In T1 Spec Lines, BMW E46 M3, add to Chassis Notes the following: SL# 1060: "BMW #GS7D36SG transmission permitted as an aftermarket sequential option." SL# 1070: "BMW #GS7D36SG transmission permitted as an aftermarket sequential option."
Applies to BMW M3 on this page: Ian Barberi
T4 Correct Ring and Pinion Ratio to T3, Sorry I Mean T4 3.7 V6 Stang
wordingT4 Ford Mustang V6 05-14 allows GT 8.8 rear axle or 7.5 axle with 3.45:1 ratio.
As printed in Fastrack
In T4 Spec Lines, Ford Mustang V6 (05-14), add to Notes the following: "GT 8.8 rear axle assembly allowed. 3.45 or 3.55 final drive ratio allowed. 7.5 rear axle assembly with 3.45:1 final drive allowed."
fasterT1 Mustang Darkhorse R gets 315 front and rear tyres, loses 500 lbs minimum weight to 3600.
As printed in Fastrack
In T1 Spec Lines, Mustang Darkhorse R (Mustang Challenge) Spec Line- 4119, change as follows: Tire size: "305 315 (f) 315(r)" Performance Control: "TBD" Min. Weight with driver (LBS): "10.5 (f) 11 (r) 3600" Chassis Notes: "Must conform to Mustang Challenge Rules. Tires conforming to Mustang Challenge rules are permitted. **This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
tyres & wheelsFF adds rocker arm and outboard suspension cars optional bias ply and VFF tires; removes front-as-rear rule, adds mixing restrictions.
As printed in Fastrack
In FF, GCR section 9.1.1.B.10.e, change as follows: "Formula F shall be limited to the following tires (front tires may not be used as rears): Dries: Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13 Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13 Wets: Front - Hoosier Wet or W3 Radial 44421 185/60R13 Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Show 16 more lines
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at least one chassis end may use the following tires: Dries: Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick or Hoosier 44165 135/545-13 VFF Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick or Hoosier 44170 165/580-13 VFF Wets: Radial wets or VFF tires listed above or Front - Hoosier 44165 135/545-13 VFF Rear - Hoosier 44170 165/580-13 VFF Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."
tyres & wheelsT4 Scion FR-S and Subaru BRZ Solo Spec allow any 200TW 225/45/17 or 215/45/17 DOT tire.
As printed in Fastrack
In T4 Spec Lines, Scion FR-S Solo Spec Coupe (13-16), change Notes as follows: "Any 200TW 225/45/17 or 215/45/17 DOT tire permitted." In T4 Spec Lines, Subaru BRZ Solo® Spec Coupe (13-16), change Notes as follows: "Any 200TW 225/45/17 or 215/45/17 DOT tire permitted."
Applies to Scion FR-S on this page: Tony Kiratsous
wordingT4 now permits B-Spec and C-Spec cars to compete in the class.
As printed in Fastrack
In GCR, Section 9.1.9.2, Touring car eligibility, change as follows: "Touring car eligibility: Cars are eligible for the class they are listed with a specification line and with the specific allowances permitted. In addition T2-T4 cars may race one class up in touring classes above their specification line class as long as they are a legal T2-T4 car and conform to their specification line allowances as classified. Cars conforming to B-Spec or C-Spec rules are permitted to compete in Touring 4."
unclearT4 Mini Cooper S R53 02-06 gear ratios changed to 12.79, 7.79, 5.65, 4.62, 3.83, 3.13 or 11.42, 7.18, 5.39, 4.40, 3.65, 2.96.
As printed in Fastrack
In T4 Spec Lines, Mini Cooper S R53 (02-06), change Gear Ratios as follows: "12.79, 7.79, 5.65, 4.62, 3.83, 3.13 or overall- 11.42, 7.18, 5.39, 4.40, 3.65, 2.96"
wordingT3 and T4 Mazda MX-5 Miata models add approved gear kit PT#-0000-02-6100 to notes.
As printed in Fastrack
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T3 Spec Lines, Mazda MX-5 Miata (16-18), add to Notes the following: "Gear kit Kit PT#- 0000-02-6100." In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, add to Notes the following: "Gear kit Kit PT#- 0000-02-6100."
Applies to Mazda MX-5 on this page: Oscar Jackson
Applies to Mazda Miata on this page: Kristina Etherington, Kayla Etherington
wordingT4 Mazda MX-5 Miata/Club/RF (19-24) and (16-18) remove discontinued hardtop part #0000-07-5901; T3 MX-5 Miata (16-18) and Global Cup ND (16-21) same.
As printed in Fastrack
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must remain stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5804-01). Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs #0000-04-9700-08, springs up to 500lb front and 300lb rear allowed. Mazda tower brace 0000-04-5626 allowed. Mazda header
Show 20 more lines
0000-06-5410 allowed." In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars allowed. Up to 500lb front and 300lb rear springs allowed. Mazda Motorsports Header part #0000-06-5410 allowed. Mazda tower brace 0000-04-5626 allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5." In T3 Spec Lines, Mazda MX-5 Miata (16-18), change Notes as follows: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Header permitted. Cold air intake permitted. Front strut brace permitted. Front and rear sway bars permitted up to 35mm, Springs 800 front and 800 Rear max permitted. Any OEM or aftermarket hardtop permitted that retains the OEM roof silhouette including Mazda hardtop part #0000-07-5902- ND and part #0000-07-5901 (discontinued DG Motorsports top). If a hardtop is used, latches shall be replaced with positive fasteners. Retractable hardtop option permitted but must be disabled from moving action and positively fastened. In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, change Notes as follows: "Shoulder harness installation must conform to FIA mounting specifications that are approved for this vehicle per section 6.2 FIA article 253, safety equipment. Must meet all ND2 MX-5 Global Cup rules. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop Mazda hardtop part #0000-07-5902-ND and #0000-07-5902-ND part #0000- 07-5901 (discontinued DG Motorsports). If a hardtop is used, latches shall be replaced with positive fasteners. OBD2 requirement does not apply. Ballast box may be removed. ND2s with sequential gearbox allowed +100 lbs.
Applies to Mazda MX-5 on this page: Oscar Jackson
Applies to Mazda Miata on this page: Kristina Etherington, Kayla Etherington
T4 Touring 4 Post-Runoffs BOP Adjustments and Changes
In T4 Spec Lines, Acura RSX/ RSX Type-S (02-06), change Restrictor as follows: "55mm FPR" In T4 Spec Lines, Acura TSX (2004-2008), change Restrictor as follows: "47mm FPR 52mm FPR" In T4 Spec Lines, BMW Z4 2.5L (03-05) , change Weight as follows: "3050 2950" In T4 Spec, BMW 320i (14-15), remove this spec line in its entirety. In T4 Spec Lines, BMW 323 (98-00), change as follows:
Show 36 more lines
Tire size: "225 245" Weight: "3250 3150" In T4 Spec Lines, Ford Mustang V6 (05-14), change as follows: Restrictor: "50mm 43mm" Weight: "3300 3400" In T4 Spec Lines, Honda Civic Si (06-11), change Restrictor as follows: "55mm" In T4 Spec Lines, Honda Civic Si (12-15), change as follows: Restrictor: "47mm 52mm Notes: "Transmission and Differential must be stock." In T4 Spec Lines, Mazda MX-5 / Club Model (06-15), change as follows: Weight: "2550 2500" Notes: "Factory bolt-in roll bar/cross member may be removed to facilitate roll cage installation. MSR option permitted. Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front spring mount PT#-0000- 04-5259, front springs #0000-04-9700-08, rear spring mount PT#-0000-04-5258, rear springs #0000- 04-9400-07, helper springs #0000-04-HLPR-EB (optional), Swaybar kit – PT#-0000-04-5306-EB that includes (front sway bar kit PT#0000-04-5306-FT, rear sway bar kit PT#-0000-04-5306-RR), offset front camber bushing PT#- 0000-04-5407-NC. Mazda Motorsports cold air intake part #0000-06-5150-KT allowed. Mazda Motorsport RX8 rear Hub Conversion kit part number 0000-04-5811-KT allowed, RX8 front hubs PT# F189-33-04X allowed. Allow Mazda header part numbers 0000-06-5407 or 0000-06-5407-NC. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including Mazda hardtop and part #0000-07-5901-CC. Aftermarket power steering reservoir is allowed. Mazda Transmission kit part # 0000-02-5700. Mazda Motorsports LSD #32655 permitted without penalty. Any other non-OEM limited slip differential allowed with +50 lbs. weight penalty. Front spoiler permitted (NF51-V4-900F). Transmission kit # 0000-02-57 In T4 Spec Lines, Pontiac Solstice / Saturn Sky (06-09), change as follows: Weight: "2800 2700" Brakes: "(F) 296 315 Vented Disc max (R) 278 Solid Disc" Notes: "GM calipers #22720705, and #25900764 permitted" In T4 Spec Lines, Scion FRS/10 series (13-16), change Weight as follows: "2925 2875" In T4 Spec Lines, Subaru BRZ/ BRZ Limited (13-16), change Weight as follows: "2925 2875" In T4 Spec Lines, Subaru BRZ (17-21), change Weight as follows: "3000 2950" In T4 Spec Lines, Toyota 86, GT (17-21), change Weight as follows: "3000 2950" SCCA Runoffs
wordingFF clarifies alternative tire eligibility for cars homologated 1989 or earlier with rocker arm or outboard suspension on all four corners.
As printed in Fastrack
In FF, GCR section 9.1.1.B.10.e, change as follows: "Alternatively, Formula F cars with rocker arm suspension (e.g., 1987-90 Reynard, Swift DB1,) and/or outboard suspension on at least one chassis end homologated in 1989 or earlier with any combination of rocker arm or outboard suspension on all four corners (e.g., 1987 – 1990 Reynard, Swift DB1) may use the following alternative tires. Note: This rule is intended to allow older cars with the described suspension design to use the alternative tires. It is not to be exploited by modifying cars with push-rods or pull-rods to meet the above requirements or by modifying either end of older cars to push- or pull-rod suspension to be eligible to run the alternative tires. Cars that were homologated in 1989 or earlier with push- or pull-rod suspension on no more than two corners may seek approval to run the alternative tire by utilizing the compliance process outlined in GCR section 8.1.4."
T4 Alternate Placement of Fuse Panel and Electronics Request
wordingT2, T3, T4 cars may relocate under-dash electronics and fuse boxes for access after roll cage installation.
As printed in Fastrack
In GCR, Section 9.1.9.2.D.9.d, add the following: "8. Under-dash electronics including computers, modules and fuse boxes may be relocated so they can be easily accessed after roll cage installation."
suspension & brakesT4 Performance now permits 1-piece alternative rotors matching spec line sizes; alternate brake kits allowed same.
As printed in Fastrack
In GCR, Section 9.1.9.2.D.6.a.6., change as follows: "In T2-Performance alternative rotors, including 2 piece rotors are permitted. Rotors must be within 5% of OE diameter or a maximum diameter of 360mm. In T3- Performance alternative rotors, including 2 piece rotors are permitted with a maximum diameter of 360mm. T4- Performance alternative 1-piece rotors are permitted but rotors must meet the sizes listed in the spec line. Spec lines showing alternate brake kits are also permitted to use 1-piece performance alternative rotors of the same size."
fasterT4 Mustang 4.0 V6 tire size increases from 245 to 255.
As printed in Fastrack
In T4 Spec Lines, Ford Mustang V6 (05-10), change as follows: Tire: "245 255" Notes: "ABS (option code 552) allowed. FR3 Handling Pack #M-2007-FR3V6 allowed (kit does not need to be run in its entirety). The kit includes: Dampers M-18000-A, Lowering Springs M-5300-N, Sway Bars M- 5490-C, Strut Tower Brace M-20201-F. Ford Positraction LSD part #M-4204-C75 is allowed. Any springs max F: 500 and R: 400 permitted. Any sway bar up to F: 35mm and R: 28mm permitted. Aftermarket Shocks conforming to T4 rules allowed. Panhard bar, part # BAR-M-4264-A permitted, or any pan hard bar permitted must be set at same length as a stock bar, center mounting hole to center mounting hole +/- 0.25 inch. An alternative steel drive shaft is permitted; this drive shaft is otherwise unrestricted, but no modifications to other components
Show 4 more lines
are permitted to facilitate its installation. An Aluminum driveshaft is allowed. Any LSD permitted. Ford brake kit M-2300-D allowed. Aftermarket header allowed. GT 8.8 rear axle assembly allowed. 3.45 or 3.55 Alternate final drive ratio allowed. 7.5 rear axle assembly with 3.45:1 final drive allowed. Cold Air Intake allowed. Koni part numbers 8741-1494SPORT (front) and 8241-1240SPORT (rear). Spec clutch #SF661 and flywheel #SF66A permitted. 14” Brembo Brake Kit#M-2300-S permitted."
fasterT2-T4 adjustable toe links now allow performance alternative bushings and spherical bearings, previously prohibited except in specified examples.
As printed in Fastrack
In GCR, Section 9.1.9.D.5.a.1., change as follows: "T2-T4: A maximum of 3.5 degrees of negative camber is allowed on front and rear suspensions. Spec line part(s) may not be modified to increase caster and camber. Strut suspensions may adjust camber and caster by the use of eccentric bushings, eccentric bolts (crash bolts) at the strut-to-spindle, and/or by use of slotted adjustment plates at the top of the strut mounting plate. If upper strut slotted adjustment plates are used, they shall be located on existing chassis structure, utilizing the unmodified manufacturer’s original bolt holes and may not serve as reinforcement for that structure. Slotted adjustment plates (strut camber plates) may incorporate a single spherical bearing (spherical bushing) and a ball thrust bearing per strut tower. On other forms of suspension, camber and caster adjustment may be achieved by the use of shims and/or eccentric
Show 4 more lines
bushings. Adjustable toe links with spherical bearings are permitted and may serve no purpose other than adjusting toe angle. Adjustable toe links are permitted. They are allowed to have performance alternative bushings and spherical bearings. They may serve no purpose other than adjusting toe angle. Spherical bearings/bushings are not permitted in T2-T4 except for the specific examples listed in the class rules or vehicle spec line."
T1 LS1 into Corvette C6 Spec Line Request
#39716 from Danny Kellermeyerhttps://crbscca.com/secu · Rule change · TB 26-02 (2026-02 Fastrack)
In T1 Spec Lines, reinstate Spec Line # 1139, Chevrolet Corvette C6 (05-13) Includes Z51, GrandSport, Z06, Z06 Carbon, as follows: Max Displ: "LS1, LS6 OEM" Min Weight: "3200" Required Restrictor: "70mm"
What the rules allowed changed as listed; this does not say what any particular car ran.