Quickest here:FA 1:35.792 Greg Labadie, Cal Club 2026 qualifying · FC 1:45.137 Robert Armington, Cal Club 2026 qualifying
FAFCsolid race · dashed qualifying · slower is lower
FAFCsolid race · dashed qualifying · each class's best lap as a share of FA's at the same event (the reference class, changeable above); 100% is level, higher is quicker
Event
FA
FC
Qual best
Race best
Trap
Qual best
Race best
Trap
vs FA
% of FA
Cal Club 2026 CALCL262026-02-21
1:35.792Greg Labadie · only car-3.750s (-3.77%)
1:37.275Greg Labadie · only car-2.623s (-2.63%)
163.8Greg Labadie+36.4 mph (+28.6%)
1:45.137Robert Armington · fastest of 4 · top 4 within 25.0s-4.930s (-4.48%)
1:45.314Robert Armington · fastest of 4 · top 4 within 12.9s-3.208s (-2.96%)
147.5Bill Wallschlaeger+33.0 mph (+28.9%)
+8.039squal +9.345s
108.3%qual 109.8%
9 rule changes (FA: 7, FC: 2)2 induction · 1 aero · 1 cars added · 1 engine · 1 tyres & wheels · 1 weight · 2 wording · FA Pro Mazda: lower intake manifold now unrestricted, throttle body raised to 80mm, wing height must not exceed 99cm, bodywork width must not exceed 132cm. · FA MZR gains alternate Noor P/N 0088-8-00 intake manifold with AT Power runners as option to Elan or Mazda Speed Elite. · FA Formula 1000 motorcycle-based engine loses maximum compression ratio 14.5:1 limit. · FA Formula 1000 allows carbon fiber external panels, forward-facing gaps, raises floor to 125mm, adds eight 75×125mm rub blocks, expands diffuser to 110cm with 75mm radius transitions. · FC USF2000 Tube Frame may use Hewland LD200 4-speed H-pattern as alternative to Hewland JL-200 5-speed sequential. · FC F2000 Metrik ZF2 minimum weight reduced to 1220 lbs. · FA class adds USF Pro 2000 car eligibility for Formula Atlantic racing. · FA Ligier JS F3 front tires may be Hoosier 43363 240/580R13 MS, rear 43368 300/590R13 MS. · FA Formula Renault 2.0 (10-17) spec notes clarified: engine sealed, manual compliance required, tire choice unrestricted, no alterations except repairs.showhide
FA Pro Mazda Classification and Performance Enhancement Proposal #39411inductionfasterFA Pro Mazda: lower intake manifold now unrestricted, throttle body raised to 80mm, wing height must not exceed 99cm, bodywork width must not exceed 132cm.
FA Alternate Intake Manifold for MZR #38223inductionunclearFA MZR gains alternate Noor P/N 0088-8-00 intake manifold with AT Power runners as option to Elan or Mazda Speed Elite.
FA Engine Compression Rule Change Request #39302enginefasterFA Formula 1000 motorcycle-based engine loses maximum compression ratio 14.5:1 limit.
FA Change Formula 1000 allowances #39608aerofasterFA Formula 1000 allows carbon fiber external panels, forward-facing gaps, raises floor to 125mm, adds eight 75×125mm rub blocks, expands diffuser to 110cm with 75mm radius transitions.
FC F2000 MZR Spec Line Clarity/Revision Requested #38927wordingneutralFC USF2000 Tube Frame may use Hewland LD200 4-speed H-pattern as alternative to Hewland JL-200 5-speed sequential.
FC Adjust F2000 Metrik ZF2 weight #39612weight -20 lbsfasterFC F2000 Metrik ZF2 minimum weight reduced to 1220 lbs.
FA Re-Consider USF Pro 2000 Car for Formula Atlantic Class #38783cars addedneutralFA class adds USF Pro 2000 car eligibility for Formula Atlantic racing.
FA Ligier JS F3 Tire Choice #38434tyres & wheelsneutralFA Ligier JS F3 front tires may be Hoosier 43363 240/580R13 MS, rear 43368 300/590R13 MS.
FA Update Formula Renault 2.0 spec line notes #37853wordingneutralFA Formula Renault 2.0 (10-17) spec notes clarified: engine sealed, manual compliance required, tire choice unrestricted, no alterations except repairs.
Cal Club 2025 CALCL252025-02-22
1:39.542Greg Labadie · only car
1:39.898Greg Labadie · only car
127.4Greg Labadie
1:50.067Paul MacFarlane · only car
1:48.522Paul MacFarlane · only car
114.4Paul MacFarlane
+8.624squal +10.525s
108.6%qual 110.6%
78 earlier rule changes on record, in force before Cal Club 2025 (from 2019)11 cars added · 8 weight · 5 engine · 5 induction · 2 tyres & wheels · 1 aero · 1 removed · 45 wording · FA adds Tatuus F.3 T-318 or FR-19 as spec line car in Table 2 for Formula Regional European Championship. · FC tire limit reduced to four dry and four wet for Regional/Major/Super Tour, eight for Runoffs. · FF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs. · FC adds F2000 Metrik ZF2 with Ford Zetec engine and four-piston Brembo calipers as spec-line car. · F600 Rotax 494, 493, 593 engines now require single expansion chamber and pull starter; electric starter optional. · FC tire marking rule clarified: four dry and wet tires for Regionals, eight each for Runoffs; damaged tire replacement procedures revised. · FA Pro Formula Mazda front wheels widen to 10 in. max; rear wheels narrow to 14 in. min. · USF2000 Van Diemen with Mazda MZR LF-DE 2.0L added as spec line car in FC; removed from FX. · FA Pro Formula Mazda maximum bodywork width behind front wheels increases to 51.97 inches. · FA MSR Formula Mazda FMzR added to Table 2 classification. · FA BDA engine displacement specification line added to Table 1, effective 2023-01-01. · FC/FF PE3-8400 ECU monitor firmware version reduced from V3.04.50 to V3.04.35. · Formula Renault 2.0 (10-17) reclassified from FX to FA; weight reduced to 1280 lbs, restrictor removed. · FA Swift 016 2.3L restrictor increases from 31mm to 32mm SIR; minimum weight drops 30 lbs to 1420. · Pro Formula Mazda allows street or bridge port, unrestricted apex seals, 70mm throttle body, 99cm wing height max, 132cm bodywork width max. · FC Ford Zetec Performance Electronics ECU model renamed PE-3 to PE3-8400; Monitor firmware updated to V3.04.50. · FA Ligier JS F3 must comply with Formula Regional Americas rules instead of FIA Formula 3 Regional Technical Regulations. · FA sealed engines must undergo full inspection; competitor pays reassembly and resealing costs. · FA Formula Lites FL15 and FR Americas Ligier JS F3 engine sealing requirements clarified to reference respective series technical regulations. · FA transmission rule clarified: transverse shafts prohibited except final drive and motorcycle gearbox in Formula 1000. · FA Swift 016 2.5 liter aero spec now references 2.3 liter notes instead of N notes. · FA Pro Formula Mazda now allows street port or bridge port, previously porting was prohibited. · FA adds Honda K20Z3 2.0L engine spec at 1350 lbs minimum and Mazda MZR 2.0L spec at 1300 lbs minimum to Table 1. · FC chassis/frame section reorganized: anti-intrusion panels between main tubes clarified, suspension mounting restrictions strengthened, firewall requirements reworded. · FC Zetec ECU requirements clarified: Pectel T2 or Performance PE-3 required with specific communications ports and SCCA tune-file/map. · FC composite anti-intrusion panels of non-uniform thickness limited to eight fasteners per side. · FC tire marking rules clarified: competitor responsible for declaring, marking, and logging tires with Tech before qualifying or race. · FA Mazda MZR 2.0 spec line removes redundant '2.0' designation; Honda Civic K20Z3 spec line unchanged. · FA Toyota 1800 moves from Table 1 to Table 2 (Spec Line Cars). · FA Swift 016 Mazda MZR/Ford Duratec wheel width specification clarified: front 10, rear 14 minimum and 15 maximum. · FA rule wording clarified: Table 1 for purpose-built and ex-pro cars, Table 2 for spec line cars with exceptions noted. · FA Mazda MZR/Ford Duratec 2296cc and 2500cc moved from Table 1 to Table 2. · FA Mazda MZR 2.0 and Honda Civic K20Z3 remove sequential designation from 5-speed transmission spec. · FA Mazda MZR 2.0 limited to Ralt RT40, RT41, Swift 008, 014 chassis; Honda Civic K20Z3 removes Swift 016 chassis. · FA Swift 016 2.3 liter engine name corrected to Mazda MZR/Ford Duratec. · FA Swift 016 2.5 liter engine name corrected to Mazda MZR/Ford Duratec. · FA removes four spec lines and replaces Ford Duratec/Mazda MZR with Honda B16 at 1615cc, 1175 lbs minimum. · FA Spec Line C loses 25 lbs to 1175; Line I loses 75 lbs to 1175; Line K gains 15 lbs to 1175. · FA purpose built and ex-Pro Atlantic cars lose 25 lb sequential transmission penalty wording. · FA Ligier JS F3 car name corrected in FR Americas spec line. · FA Ford Duratec/Mazda MZR 2500 spec line D wording cleanup: 4-valve becomes 4 valves per cylinder. · FA Honda Civic K20Z3 intake manifold and throttle body assembly now allows AT Power Direct-To-Head 45mm individual throttle bodies as alternative to HPD parts. · FA Ford Duratec/Mazda MZR intake restrictor reduced from 32mm to 30mm SIR; Swift 016 2.5 Mazda restrictor reduced from 35mm to 33mm SIR. · FA Toyota 4A-GE engines cleaned up, spec lines A and B engine designations corrected. · FA Ford BD Series max displacement increases from 1600 to 1615 cc, minimum weight stays 1200 lbs. · FA Ford Duratec/Mazda MZR and Honda B16 both now 1615cc max displacement; Honda B16 removes NA requirement. · FA Pro Formula Mazda engine specs moved from Table 1 to Table 2 notes; Renesis Rotary details consolidated. · FA F3 Americas spec line updated effective 2021-03-01; specific changes not legible in provided text. · FC Pinto engine loses 10 lbs to 1190; Pinto aluminum head loses 10 lbs to 1190; Zetec loses 10 lbs to 1210. · Formula Lites Crawford FL15 newly classified in FA. · FC: Pectel T2 and Performance PE-3 ECU maps clarified; SCCA Club or 2013 Pro map required. · FC Zetec engine minimum weight increases 20 lbs to 1220 lbs. · FA stock engines not given weight adjustment; modified engines now allowed in class. · FA engine modifications wording clarified: bore/crankshaft/stroke/flywheel unrestricted if displacement limit met, distributor/transistor ignition allowed without engine modification, compression ratio increasable by machining/gasket chang… · FA transmission rules clarified: no more than five forward speeds and operational reverse gear unless Table 2 notes otherwise. · FA Swift 016 Mazda Duratec Gurney flap wording clarified; terminology and mounting rules unchanged. · FA Volkswagen 1835cc SOHC removed from Table 1. · FA engine rules clarified: blocks and heads must be OEM unless Tables note exceptions. · FA Formula 1000 motorcycle-based engine compression ratio raised to 14.5:1 from 13.5:1. · FA removes Ex-FSV front wheel width 6–8 inches and rear 8–10 inches provisions; all cars use front 10 inches, rear 14–15 inches. · FA Formula 3 engines now allowed through 2017, previously 2008, with 30mm restrictor required. · FA engine note clarification removes Table E reference, Pro Formula Mazda directed to Table 1. · Formula 1000 motorcycle-based engine classified into FA, throttle bodies and ECUs unrestricted. · F1000 reclassified into FA with specification changes effective 2020-01-01. · FA Swift 016 2.3L Mazda Duratec restrictor reduced from 33mm to 31mm SIR, making it slower. · FA wheel dimension rules moved from Bodywork subsection to General section; no specification changes. · FA Mazda MZR 2.0 now limited to Ralt RT40, Ralt RT41, and Swift 014 chassis only. · FC Zetec connecting rods now allow Eagle #CRS5483F3D in addition to original Ford. · FC adds Mahle #930169439 piston as alternate option to existing Ford, Sealed Power, and United Engine choices. · FA Honda Civic K20Z3 engines consolidated: three separate base/uprated specs removed, replaced with single unified 1350 lb minimum weight spec for Swift 014/016. · FA Swift 014 Mazda MZR 2.0 piston minimum weight reduced from 320g to 280g. · FA Line N minimum weight increases to 1375 lbs. · FA cars must install AIM part #X47KPFSOLO2R0 data box mount for Majors and Runoffs. · FC Wiseco piston and Crower connecting rod part numbers updated; minimum weight 976 grams. · FA Formula 3 car sequential gearbox weight penalty of 25 lbs removed; minimum weight now 1215 lbs. · FA Swift 014-Mazda MZR 2.0 engine now requires OE block casting #LF95 and specific OE components instead of sealed Elite Engines sourcing. · FA Swift 016 Mazda Duratec 2.3L and 2.5L minimum weight increases from 1420 to 1450 lbs. · FC Wiseco piston and Crower connecting rod assembly minimum weight increases from 555 to 976 grams.showhide
FA Classify FR European Championship car as spec line car in Table 2 #37658cars addedneutralFA adds Tatuus F.3 T-318 or FR-19 as spec line car in Table 2 for Formula Regional European Championship.
FC 9.1.1.10.h. FC Tire Rule #36533tyres & wheelsslowerFC tire limit reduced to four dry and four wet for Regional/Major/Super Tour, eight for Runoffs.
FC Change FF/FC Weight with Sequential Gearbox #36651weightfasterFF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs.
FC Four Pot Calipers #35481cars addedneutralFC adds F2000 Metrik ZF2 with Ford Zetec engine and four-piston Brembo calipers as spec-line car.
FC Please correct omitted punctuation #34890engineneutralF600 Rotax 494, 493, 593 engines now require single expansion chamber and pull starter; electric starter optional.
FC Review FC Runoffs Tire Marking Rule #34274wordingneutralFC tire marking rule clarified: four dry and wet tires for Regionals, eight each for Runoffs; damaged tire replacement procedures revised.
FA Simplify Pro Formula Mazda wheel allowance #34190tyres & wheelsunclearFA Pro Formula Mazda front wheels widen to 10 in. max; rear wheels narrow to 14 in. min.
FC USF2000 Van Diemen with Mazda MZR LF-DE 2.0L in FC #34329cars addedneutralUSF2000 Van Diemen with Mazda MZR LF-DE 2.0L added as spec line car in FC; removed from FX.
FA E&O - Correct Pro Formula Mazda spec line dimensional equivalent #34085aerofasterFA Pro Formula Mazda maximum bodywork width behind front wheels increases to 51.97 inches.
FA Add new spec line for MSR Formula Mazda FMzR to Table 2 #34139cars addedneutralFA MSR Formula Mazda FMzR added to Table 2 classification.
FA BDA Displacement #33431wordingneutralFA BDA engine displacement specification line added to Table 1, effective 2023-01-01.
FC E&O 9.1.1.B.16.j #33634wordingunclearFC/FF PE3-8400 ECU monitor firmware version reduced from V3.04.50 to V3.04.35.
FA Reclassify 2010-2017 Formula Renault 2.0 as a spec line car in FA #33395cars addedfasterFormula Renault 2.0 (10-17) reclassified from FX to FA; weight reduced to 1280 lbs, restrictor removed.
FA Change Swift 016 2.3L restrictor size and minimum weight #33472induction -30 lbsfasterFA Swift 016 2.3L restrictor increases from 31mm to 32mm SIR; minimum weight drops 30 lbs to 1420.
FA Pro Formula Mazda Dimension E&O #33160wordingneutralPro Formula Mazda allows street or bridge port, unrestricted apex seals, 70mm throttle body, 99cm wing height max, 132cm bodywork width max.
FC Add Specification to Performance Electronics ECU for Ford Zetec #32761wordingneutralFC Ford Zetec Performance Electronics ECU model renamed PE-3 to PE3-8400; Monitor firmware updated to V3.04.50.
FA Update FR Americas rulebook requirement #32491wordingneutralFA Ligier JS F3 must comply with Formula Regional Americas rules instead of FIA Formula 3 Regional Technical Regulations.
FA Clarify verification of sealed engine compliance #32522wordingneutralFA sealed engines must undergo full inspection; competitor pays reassembly and resealing costs.
FA Clarify Formula Lites and FR Americas sealed engine requirement #32523wordingneutralFA Formula Lites FL15 and FR Americas Ligier JS F3 engine sealing requirements clarified to reference respective series technical regulations.
FA E&O FA Transmission section #32251wordingneutralFA transmission rule clarified: transverse shafts prohibited except final drive and motorcycle gearbox in Formula 1000.
FA E&O Swift 016 2.5 liter Aero column #32363wordingunclearFA Swift 016 2.5 liter aero spec now references 2.3 liter notes instead of N notes.
FA Closing the Gap #31934inductionfasterFA Pro Formula Mazda now allows street port or bridge port, previously porting was prohibited.
FA Reorganize Tables 1 and 2 #31985cars addedneutralFA adds Honda K20Z3 2.0L engine spec at 1350 lbs minimum and Mazda MZR 2.0L spec at 1300 lbs minimum to Table 1.
FC Clean up Chassis/Frame section #31867wordingneutralFC chassis/frame section reorganized: anti-intrusion panels between main tubes clarified, suspension mounting restrictions strengthened, firewall requirements reworded.
FC Clarify Zetec ECU requirements #31554wordingneutralFC Zetec ECU requirements clarified: Pectel T2 or Performance PE-3 required with specific communications ports and SCCA tune-file/map.
FC Clarify composite anti-intrusion panel language #31426wordingneutralFC composite anti-intrusion panels of non-uniform thickness limited to eight fasteners per side.
FC Clarify tire marking requirements #31455wordingneutralFC tire marking rules clarified: competitor responsible for declaring, marking, and logging tires with Tech before qualifying or race.
FA E&O Table 2 engine names #31085wordingneutralFA Mazda MZR 2.0 spec line removes redundant '2.0' designation; Honda Civic K20Z3 spec line unchanged.
FA Move Toyota 1800 to Table 2 #30822cars addedneutralFA Toyota 1800 moves from Table 1 to Table 2 (Spec Line Cars).
FA E&O Swift 016 wheel width reference #30939wordingneutralFA Swift 016 Mazda MZR/Ford Duratec wheel width specification clarified: front 10, rear 14 minimum and 15 maximum.
FA Update FA rules package #30717wordingneutralFA rule wording clarified: Table 1 for purpose-built and ex-pro cars, Table 2 for spec line cars with exceptions noted.
FA Move Mazda MZR/Ford Duratec 2296cc and 2500cc to Table 2 #30718wordingneutralFA Mazda MZR/Ford Duratec 2296cc and 2500cc moved from Table 1 to Table 2.
FA Clean up Table 2 Mazda MZR 2.0L and Honda Civic K20Z3 spec lines #30719wordingneutralFA Mazda MZR 2.0 and Honda Civic K20Z3 remove sequential designation from 5-speed transmission spec.
FA E&O Mazda MZR 2.0 and Honda Civic K20Z3 chassis eligibility #30632wordingneutralFA Mazda MZR 2.0 limited to Ralt RT40, RT41, Swift 008, 014 chassis; Honda Civic K20Z3 removes Swift 016 chassis.
FA Correct engine name in Swift 016 2.3 liter spec line #30447wordingneutralFA Swift 016 2.3 liter engine name corrected to Mazda MZR/Ford Duratec.
FA Correct engine name in Swift 016 2.5 liter spec line #30448wordingneutralFA Swift 016 2.5 liter engine name corrected to Mazda MZR/Ford Duratec.
FA Revise Table 1 Spec Lines and clarify application of Engine Notes #30456cars addedunclearFA removes four spec lines and replaces Ford Duratec/Mazda MZR with Honda B16 at 1615cc, 1175 lbs minimum.
FA Update Table 1 Weights for Spec Lines C, I, and K #30355weight -25 lbsfasterFA Spec Line C loses 25 lbs to 1175; Line I loses 75 lbs to 1175; Line K gains 15 lbs to 1175.
FA Remove redundant reference in Table 2 spec line #30366wordingfasterFA purpose built and ex-Pro Atlantic cars lose 25 lb sequential transmission penalty wording.
FA Correct the name of the FR Americas car #30369wordingneutralFA Ligier JS F3 car name corrected in FR Americas spec line.
FA Clean up Spec Line D in Table 1 #30372wordingneutralFA Ford Duratec/Mazda MZR 2500 spec line D wording cleanup: 4-valve becomes 4 valves per cylinder.
FA Table 2 Honda K20Z3 request #30386inductionfasterFA Honda Civic K20Z3 intake manifold and throttle body assembly now allows AT Power Direct-To-Head 45mm individual throttle bodies as alternative to HPD parts.
FA E&O FA Intake Restrictors #30273inductionslowerFA Ford Duratec/Mazda MZR intake restrictor reduced from 32mm to 30mm SIR; Swift 016 2.5 Mazda restrictor reduced from 35mm to 33mm SIR.
FA Clean up Spec Lines A and B in Table 1 #30274wordingneutralFA Toyota 4A-GE engines cleaned up, spec lines A and B engine designations corrected.
FA Clean up Spec Line C in Table 1 #30275enginefasterFA Ford BD Series max displacement increases from 1600 to 1615 cc, minimum weight stays 1200 lbs.
FA Clean up Spec Lines J and L in Table 1 #30276wordingneutralFA Ford Duratec/Mazda MZR and Honda B16 both now 1615cc max displacement; Honda B16 removes NA requirement.
FA Move engine specifications to Pro Formula Mazda spec line notes #30278wordingneutralFA Pro Formula Mazda engine specs moved from Table 1 to Table 2 notes; Renesis Rotary details consolidated.
FA Update F3 Americas spec line #30280wordingunclearFA F3 Americas spec line updated effective 2021-03-01; specific changes not legible in provided text.
FC Request for FC Weight Change #30171weightfasterFC Pinto engine loses 10 lbs to 1190; Pinto aluminum head loses 10 lbs to 1190; Zetec loses 10 lbs to 1210.
FA Request to classify Formula Lites Crawford FL15 #29702cars addedneutralFormula Lites Crawford FL15 newly classified in FA.
FC Urgent: SCCA PE3 map unsuitable #29475wordingneutralFC: Pectel T2 and Performance PE-3 ECU maps clarified; SCCA Club or 2013 Pro map required.
FC Request for weight adjustments to equalize FC competition. #28888weightslowerFC Zetec engine minimum weight increases 20 lbs to 1220 lbs.
FA Request to Adjust FB Weight for Stock Engines #29005wordingneutralFA stock engines not given weight adjustment; modified engines now allowed in class.
FA E&O permitted engine modifications #28831wordingneutralFA engine modifications wording clarified: bore/crankshaft/stroke/flywheel unrestricted if displacement limit met, distributor/transistor ignition allowed without engine modification, compression ratio increasable by machining/gasket chang…
FA E&O Transmissions #28832wordingneutralFA transmission rules clarified: no more than five forward speeds and operational reverse gear unless Table 2 notes otherwise.
FA Swift 016 Gurney flap wicker clarification #28884wordingneutralFA Swift 016 Mazda Duratec Gurney flap wording clarified; terminology and mounting rules unchanged.
FA Remove redundant spec line in Table 1 #28720removedneutralFA Volkswagen 1835cc SOHC removed from Table 1.
FA E&O general engine rules #28772wordingneutralFA engine rules clarified: blocks and heads must be OEM unless Tables note exceptions.
FA Request higher compression ratio and prior weights for F1000 cars #28162enginefasterFA Formula 1000 motorcycle-based engine compression ratio raised to 14.5:1 from 13.5:1.
FA Remove redundant wheel dimension provisions #28554wordingneutralFA removes Ex-FSV front wheel width 6–8 inches and rear 8–10 inches provisions; all cars use front 10 inches, rear 14–15 inches.
FA E&O Formula 3 spec line #28596enginefasterFA Formula 3 engines now allowed through 2017, previously 2008, with 30mm restrictor required.
FA FA weight correction/clarification #28430wordingneutralFA engine note clarification removes Table E reference, Pro Formula Mazda directed to Table 1.
FA Request to merge FB into FA #25611cars addedfasterFormula 1000 motorcycle-based engine classified into FA, throttle bodies and ECUs unrestricted.
FA Suggestions for FB/F1000 into FA #27319cars addedunclearF1000 reclassified into FA with specification changes effective 2020-01-01.
FA Change Swift 016 - 2.3 liter Mazda Duratec restrictor size #27880inductionslowerFA Swift 016 2.3L Mazda Duratec restrictor reduced from 33mm to 31mm SIR, making it slower.
FA Move wheel dimensions from Bodywork subsection to #27493wordingneutralFA wheel dimension rules moved from Bodywork subsection to General section; no specification changes.
FA Table 2 Mazda MZR 2.0 E&O #27640wordingneutralFA Mazda MZR 2.0 now limited to Ralt RT40, Ralt RT41, and Swift 014 chassis only.
FC Request for Better Zetec Connecting Rods #27710wordingneutralFC Zetec connecting rods now allow Eagle #CRS5483F3D in addition to original Ford.
FC Add Alternate Piston #27795wordingneutralFC adds Mahle #930169439 piston as alternate option to existing Ford, Sealed Power, and United Engine choices.
FA Follow up to Letter #27344 on Honda Powered FA Rules #27363wordingneutralFA Honda Civic K20Z3 engines consolidated: three separate base/uprated specs removed, replaced with single unified 1350 lb minimum weight spec for Swift 014/016.
FA Swift 014 Mazda MZR 2.0 E&O #27305enginefasterFA Swift 014 Mazda MZR 2.0 piston minimum weight reduced from 320g to 280g.
FA Adjust Line N restrictor size and minimum weight #26691weight +30 lbsslowerFA Line N minimum weight increases to 1375 lbs.
FA Add data plate requirement #26707wordingneutralFA cars must install AIM part #X47KPFSOLO2R0 data box mount for Majors and Runoffs.
FC E&O Wiseco piston and Crower connecting rod #26659wordingneutralFC Wiseco piston and Crower connecting rod part numbers updated; minimum weight 976 grams.
FA Request to add FA engine spec lines #26183weightfasterFA Formula 3 car sequential gearbox weight penalty of 25 lbs removed; minimum weight now 1215 lbs.
FA FA MZR 2.0 Engine Specification #25814wordingneutralFA Swift 014-Mazda MZR 2.0 engine now requires OE block casting #LF95 and specific OE components instead of sealed Elite Engines sourcing.
FA FA 016 weight increase #26063weightslowerFA Swift 016 Mazda Duratec 2.3L and 2.5L minimum weight increases from 1420 to 1450 lbs.
FC Correct Wiseco piston and connecting rod #25809weightslowerFC Wiseco piston and Crower connecting rod assembly minimum weight increases from 555 to 976 grams.
Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of FA" is the class's best as a share of FA's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when FA's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.