This track has been raced on 4 configurations (The Circuit, 2.57 mi; 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
One run is left out as not that car's own laps (far quicker than the car managed in any other session and than anyone else in its class all week; usually a swapped transponder): Tom Burt in Cal Club 2025 PM (1:42.300; the car's best in any other session was 1:52.334 and the rest of the class's best all week 1:50.233).
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
MG Midget
HP
4
1:40.295Bill Okell
2:04.965Brian Linn
2:03.082Lee Fleming
126.2Lee Fleming
27.543Bill Okell
28.857Bill Okell
43.861Bill Okell
BMW M3
T1
1
1:46.465Ian Barberi
1:46.465Ian Barberi
1:47.434Ian Barberi
114.9Ian Barberi
28.992Ian Barberi
30.811Ian Barberi
46.263Ian Barberi
BMW M4 GT4
T1
1
1:47.084Drew Delmonico
1:47.084Drew Delmonico
1:47.467Drew Delmonico
161.4Drew Delmonico
29.150Drew Delmonico
30.850Drew Delmonico
46.316Drew Delmonico
SCCA Ent SRF3
SRF3
38
1:50.233Caleb Shrader
1:50.233Caleb Shrader
1:50.825Caleb Shrader
138.9Paul Marino
30.136Caleb Shrader
31.672Caleb Shrader
44.841Tom Burt
Pontiac GTO
T1
1
1:59.123Ed Gless
1:59.760Ed Gless
1:59.123Ed Gless
120.7Ed Gless
32.383Ed Gless
34.587Ed Gless
51.370Ed Gless
Ford Mustang
T1
1
1:59.261Pratt Cole
1:59.261Pratt Cole
98.6Pratt Cole
32.624Pratt Cole
34.661Pratt Cole
51.577Pratt Cole
Toyota Yaris
HP
1
2:08.224Bobby Beyer
2:10.927Bobby Beyer
2:08.224Bobby Beyer
92.3Bobby Beyer
34.660Bobby Beyer
37.206Bobby Beyer
56.144Bobby Beyer
Mini Cooper
HP
1
2:09.238Tom Tuttle
2:11.042Tom Tuttle
2:09.238Tom Tuttle
99.0Tom Tuttle
34.631Tom Tuttle
37.306Tom Tuttle
56.479Tom Tuttle
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
SRF3 Update SRF Brake Rule
#33469 from Robey Clark · Rule change · TB 23-01 (2023-01 Fastrack)
slowerSRF Renault Alliance solid front rotors banned; restrictor reduced 35mm to 34mm for 2011+ Kawasaki; minimum weight increased to 1100 lbs for 2009+ stock engines.
In SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481"). The 1985 Renault Alliance solid front rotor (Reference: Bendix PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type rotor. The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038 may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind;
Show 4 more lines
maximum of one spring per caliper." P2 Engine Table Spec Line Engine Series
A specification table follows in the original; it is not shown here.
T1 Sequential Gearbox Limitations in T1
#33691 from David Mead · Rule change · TB 23-03 (2023-03 Fastrack)
neutralT1 cars with aftermarket sequential transmissions get 10-inch max bellhousing; non-sequential cars gain 100 lbs weight break.
In GCR, Section 9.1.9.1.I.4., change as follows: "Aftermarket sequential transmissions are permitted. Cars with aftermarket sequential shift transmissions shall utilize a 1:1 (or greater/overdriven) ratio in top gear. Transmission location must be OEM. Maximum bellhousing length is 10 inches. Cars that don’t use an aftermarket sequential transmission may decrease their competition weight by 100 lbs."
SRF3 Update SRF Bodywork Fitment Rule
#33765 from Robey Clark · Rule change · TB 23-03 (2023-03 Fastrack)
neutralSRF3 tail sections allowed on SRFs with GEN3 airbox shimming up to 19 mm; alternate dash panel P/N 180100 or 180101 relocated in rules.
In Spec Racer Ford, GCR section 9.1.8.D.1.E, change as follows: "j. Optional Bodywork Modification: Viewing the tail section of the car from behind, draw a vertical line at the left and right ends of the outer vents from the bottom edge of the bodywork up to a point two (2) inches below the crease at the lower edge of the vented panel. Make a vertical cut at each line. The horizontal cut is to be one (1) inch below the crease at the base of the vented panel. Leave a one (1) inch radius at each corner. Air Scoop (P/N 190000) must be installed in conjunction with rear cutout per Enterprises installation instructions. SRF3 tail sections are allowed on SRFs. For purposes of tail section to center section fitment with the GEN3 airbox, shimming is allowed at the rear of the center section. Shim material may be up to 19 mm (0.75") thick along the 1" upper square sidepod
Show 11 more lines
tube. Mounting location cannot be modified or added. Shim material must be securely attached, but must not be welded. An alternate dash panel has been approved for use in Spec Racer Fords. The dash will be furnished by Enterprises only. P/N 180100 or 180101 k. Required Bodywork Modification: A 22.5" diameter wheel arch shall be cut in each side of the tail section. Viewing the tail section from the side, draw a vertical line at the drive axle centerline. Locate the top of the wheel arch at a point measured from the bottom edge of the tail section 9.25" vertically along the centerline. The 22.5" diameter circle intersects the bottom edge of the tail section 11.1" either side of the centerline. The tail section may be reinforced in the forward and aft portions of the wheel arch. Dimension tolerance is +/- 0.75". l. An alternate dash panel has been approved for use in Spec Racer Fords. The dash will be furnished by Enterprises only. P/N 180100 or 180101."
neutralT1 GT4 weights clarified for nine cars, ranging from 3200 lbs Porsche 718 Cayman to 3575 lbs Aston Martin.
RM 23-04 – Touring 1 weights dated 3/21/2023 As an E&O to the February Fastrack, in T1-GT4 leave weights as follows: Aston Martin Vantage AMR GT4: 3575 Audi R8 GT4: 3550 BMW M4 GT4: 3500 Ford Mustang GT4: 3550 Maclaren 570S GT4: 3450 Mercedes AMG GT4: 3450
Show 3 more lines
Porsche 718 Cayman GT4 CS MR: 3200 Porsche 718 GT4 RS Clubsport: 3450 Toyota Supra GR GT4: 3350
SRF3 Update SRF Front W2 Rain Tire Part Number
#34118 from Robey Clark · Rule change · TB 23-05 (2023-05 Fastrack)
neutralSRF Hoosier front rain tyre part number changes from 46100 to 46101 P185/65R13 W2.
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Front – Hoosier P/N 46100 1 P185/65R13 W2"
T1 Touring 1 Tire Sizes
#34191 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)
fasterT1-GT4 McLaren 570S and Mercedes AMG GT4 front tires widen to 315 mm.
#34048 from David Mead · Rule change · TB 23-06 (2023-05 Fastrack)
neutralT1 Ford Mustang S197 (05-14) reinstated with 3550 lbs minimum weight, 75mm restrictor, Voodoo engine permitted.
In T1 Spec Lines, classify Ford Mustang S197 (05-14) Includes GT, Boss302, 302S, 302R, FR500C, FR500S as follows:
A specification table follows in the original; it is not shown here.
Applies to Ford Mustang on this page: Pratt Cole
SRF3 Hoosier SRF Wet Front Tire Rule Update
#34189 from Robey Clark · Rule change · TB 23-06 (2023-06 Fastrack)
unclearSRF Hoosier wet front tire updated to P/N 46100 P185/60R13 H20 or W2.
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."
neutralFord Fiesta HP and Chevrolet Sonic FP model year ranges extended from 2016 to 2019.
In HP, adjust model years of the "Ford Fiesta (11-16)" spec line as follows: "Ford Fiesta (11-16 9)" In FP, adjust model years of the "Chevrolet Sonic (12-16)" spec line as follows: "Chevrolet Sonic (12-16 9)"
T1 Gen 5 Camaro Engine
#33875 from Matt Spicuzzi · Rule change · TB 23-06 (2023-07 Fastrack)
neutralT1 Chevrolet Camaro Gen 5 LS7 gets two spec lines: 1131 with 70mm restrictor, 1136 with 53mm restrictor, both 3450 lbs minimum.
In T1-NEW Spec Lines, Chevrolet Camaro Gen 5 (10-15) Including SS, Z28, classify Spec Line Number 1131 and 1136 as follows:
A specification table follows in the original; it is not shown here.
T1 Inquiry to letter #33682
#34071 from Andrew Aquilante · Rule change · TB 23-06 (2023-07 Fastrack)
slowerT1 Chevrolet Camaro Gen 5, Corvette C5 and C6: engine resleeve restricted to stock parameters only, no longer LS3 bore/stroke.
In T1 NEW Spec Lines, Chevrolet Camaro Gen 5 (10-15) Including SS, Z28, change Engine Notes as follows: 1130: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1135: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement.May resleeve to stock parameters for engine repair or replacement." In T1 NEW Spec Lines, Chevrolet Corvette C5 (‘97-’04) – Includes: Z06, Coupe, Convertible, change Engine Notes as follows: 1132: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement."
Show 18 more lines
1134: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1136: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1138: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." In T1 NEW Spec Lines, Chevrolet Corvette C6 (05-13) - Includes Z51, GrandSport, Z06, Z06 Carbon, change Engine Notes as follows: 1150: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1160: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1170: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1180: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement." 1190: "May resleeve any LS block to LS3 bore/ stroke for Engine replacement. May resleeve to stock parameters for engine repair or replacement."
T1 Viper Cleanup
#34107 from Scotty B White · Rule change · TB 23-06 (2023-05 Fastrack)
fasterT1 Dodge Viper ACR/ACR-X restrictor increases from 50mm to 60mm flat plate.
In T1 NEW Spec Lines, Dodge Viper ACR/ACR-X Spec Line 1360, change Required Restrictor as follows: "50mm 60mm flat plate"
T1 Viper 8300 OEM FPR Size
#34268 from Scotty B White · Rule change · TB 23-06 (2023-05 Fastrack)
unclearT1 Dodge Viper ACR/ACR-X: Spec Line 1370 restrictor increases to 55mm, Line 1390 decreases to 55mm.
In T1 NEW Spec Lines, Dodge Viper ACR/ACR-X Spec Line 1370, change Required Restrictor as follows: "(2) 47mm 55mm flat plates" In T1 NEW Spec Lines, Dodge Viper ACR/ACR-X Spec Line 1390, change Required Restrictor as follows: "(2) 60mm 55mm flat plates"
HP ITC to FP?
#34286 from David Snow · Rule change · TB 23-06 (2023-07 Fastrack)
neutralHP Volkswagen Rabbit Cabriolet 1780 removed; Rabbit 1588 and 1715 reclassified with engine sizes and year ranges specified.
In HP Spec Lines, Volkswagen Rabbit Cabriolet 1780, delete in its entirely: In HP, Spec Lines, Volkswagen Rabbit, change Title as follows: “Volkswagen Rabbit 1588 (includes Cabriolet / convertible)” “Volkswagen Rabbit 1715 (81-84) (excl. conv.)” “Volkswagen Rabbit GTI 1780 (83-84)”
HP Correct Intake Valve Size on 1500cc Midget/Spitfire
#34419 from Production Committee · Rule change · TB 23-06 (2023-05 Fastrack)
neutralFP and HP Sprite, Midget, and Spitfire 1500 intake valve size corrected to 36.6/(1.44).
In FP Spec Lines, Austin-Healey Sprite Mk. I, II,III, IV MG Midget Mk I,II, III, IV & 1500, change Intake Valve Size as follows: "(I) 36.65.3/(1.44)" In FP Spec Lines, Triumph Spitfire Mk. IV & 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)" In HP Spec Lines, Triumph Spitfire Mk. III & IV 1500, change Intake Valve Size as follows: "(I) 36.65.5/(1.440)"
T1 Ford Mustang S197 (05-14) Clarification
#34450 from Club Racing Board · Rule change · TB 23-06 (2023-05 Fastrack)
neutralT1 Ford Mustang S197 05-14 now requires OEM 8.8 differential housing.
In T1-NEW Spec lines, Ford Mustang S197 (05-14) Includes GT, Boss302, 302S, 302R, FR500C, FR500S, change Notes as follows: "OEM 8.8 Differential Housing"
T1 C5 Approved Aero That Was Mistakenly Deleted
#34374 from Joe Aquilante · Rule change · TB 23-08 (2023-08 Fastrack)
fasterT1 Corvette C5 gains approved aero parts: carbon rear spoiler, vented front splitter, side skirts, with 50 lb weight reduction allowed.
In T1 NEW Spec Lines, Chevrolet Corvette C5 (‘97-’04) – Includes: Z06, Coupe, Convertible, Spec Lines 1132-1138, add to Notes as follows: "Any option of OEM Bodywork parts may be used as basis for aero measurements. Rear spoiler max 5” Above bumper allowed. +50lbs. The following parts are permitted, with a 50lb decrease from base weight, in lieu of the aero options permitted in 9.1.9.1.B: (C7Carbon Rear- Spoiler CCC5 EX- RSB-GB, Vented Front Splitter CCC5-FS-GB, Side Skirts CCC5 SS-GB.)"
T1 Why no Camaro?
#34421 from Scotty B White · Rule change · TB 23-08 (2023-05 Fastrack)
neutralChevrolet Camaro GT4-R classified in T1 GT4 Spec Line 4035, minimum weight 3375 lbs, 315 max tire, 63mm restrictor, ineligible for Runoffs.
In T1 GT4 Spec Lines, classify Chevrolet Camaro GT4-R as follows:
A specification table follows in the original; it is not shown here.
T1 Request to Remove Expiration from T1 spec lines #1350 & #1370
#34470 from Scotty B White · Rule change · TB 23-08 (2023-05 Fastrack)
neutralT1 Dodge Viper ACR / SRT RT-10 and ACR/ACR-X spec lines 1350 and 1370 remove 12/23 expiration.
In T1 NEW Spec Lines, Dodge Viper ACR / SRT RT-10, change Spec Line Number as follows: "1350 *Spec line Expires 12/23*" In T1 NEW Spec Lines, Dodge Viper ACR/ACR-X, change Spec Line Number as follows: "1370 *Spec line Expires 12/23*"
In HP Spec Line, Nissan/Datsun PL510, change Carburetor. No. & Type as follows: "(1) 40 DCN, DCNF w/ 32 4mm choke(s), . or (1) 36mm DCNVH. (2) auto type side draft(s) w/ 32 4mm choke(s) on I.R. manifold @ 90lbs penalty."
SRF3 SRF Radiator Rule Update
#34805 from Robey Clark · Rule change · TB 23-10 (2023-10 Fastrack)
neutralSRF radiator rule clarified: P/N 480466 replaceable with Automotive P/N 1R698, CU698 or manufacturer equivalent with documentation.
In SRF, GCR section 9.1.8.D.1.V.j, change as follows: "Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent, as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."
T1 New T1 add spec line for C5 corvette LS2 engines (Copy from C6)
#33764 from Craig Anderson · Rule change · TB 23-12 (2023-09 Fastrack)
neutralT1 Chevrolet Corvette C5 LS2 added with 6000cc displacement, 3300 lbs minimum weight, 72mm flat plate restrictor.
In T1 Spec Lines, classify Chevrolet Corvette C5 (‘97-’04) – Includes: Z06, Coupe, Convertible as follows:
A specification table follows in the original; it is not shown here.
T1 2004 - 2006 Pontiac GTO Re-Integration Back Into T1
#34403 from Ed Gless · Rule change · TB 23-12 (2023-12 Fastrack)
neutralPontiac GTO 2006-2009 re-integrated into T1 with LS2 at 3400 lbs, 72mm restrictor, and LS3 at 3500 lbs, 61mm restrictor.
In T1 Spec Lines, classify Pontiac GTO 2006-2009 as follows:
A specification table follows in the original; it is not shown here.
Applies to Pontiac GTO on this page: Ed Gless
T1 Request to Classify Porsche 997-1 GT3 Cup
#34561 from Scotty B White · Rule change · TB 23-12 (2023-12 Fastrack)
neutralT1 Porsche 997-1 GT3 Cup added at spec line 4210, minimum weight 3050 lbs.
In T1 Spec Lines, delete the Porsche 996 GT3 Cup car from the standard spec lines and classify "Homologated car" section as follows: T1 – Homologated Cars
A specification table follows in the original; it is not shown here.
T1 C7 Corvette Rule Change Request
#34897 from Heath Karl · Rule change · TB 23-12 (2023-09 Fastrack)
neutralT1 Chevrolet Corvette C7 (14-19) including Z51, Grandsport newly classified as homologated car.
In T1 Spec Lines, classify Chevrolet Corvette C7 (14 - 19) - Includes Z51, Grandsport as follows: T1 – Homologated Cars
A specification table follows in the original; it is not shown here.
HP Porsche 944/924S Rule Change Request
#35002 from Adam Achepohl · Rule change · TB 23-12 (2023-12 Fastrack)
neutralEP Porsche 944/924S combines 2.5L and 2.7L variants with new weights: 2250–2415 lbs depending on engine and year.
In EP Spec Lines, delete the Porsche 944/924S 2.5L (2V) (83-88) spec line entirely, and create a new spec line for Porsche 944/924S 2.5L(2V) 2.7L(2V) (83-89) as follows:
A specification table follows in the original; it is not shown here.
HP FP and HP Toyota Corolla
#35030 from Keith Church · Rule change · TB 23-12 (2023-12 Fastrack)
fasterFP Toyota Corolla 2TC loses 43 lbs to 1810; HP Corolla loses 50–52 lbs to 1910–2006.
In FP Spec Lines, Toyota Corolla 2TC (71-74), change weight as follows: "1853 1810" In HP Spec Lines, Toyota Corolla (71-74), change weight as follows: “1960 1910 * 2009 1958 ** 2058 2006”
HP Weight Reduction for Mazda 626
#35031 from David Reiter · Rule change · TB 23-12 (2023-12 Fastrack)
fasterHP Mazda 626 84-87 weight reduced to 2200 lbs, 2255 lbs, and 2310 lbs across three configurations.
In HP Spec Lines, Mazda 626 (84-87), change weight as follows: "2300 2200 *2358 2255 **2415 2310"
HP Triumph GT6 Adjustments
#35054 from ANTHONY PARKER · Rule change · TB 23-12 (2023-12 Fastrack)
fasterEP Triumph GT6 minimum weight reduced to 1800 lbs.
In EP Spec Lines, Triumph GT6, change weight as follows: "1830 1800"
T1 Camaro Gen 5 Weight Reduction Due to Competitive Disadvantage
#35092 from Clark Nunes · Rule change · TB 23-12 (2023-09 Fastrack)
fasterT1 Gen 5 Camaro minimum weight drops 75 lbs to 3475; restrictor increases 70mm to 75mm.
In T1 Spec Lines, Gen 5 Camaro, change as follows: Spec Line 1130 - Minimum Weight "3550 3475" Spec Line 1135 - Minimum Weight "3550 3475" Restrictor Required "70mm 75mm-Flat Plate"
fasterHP Honda CRX 1.5 (88-91) weight reduced to 2175 lbs, 2229 lbs, and 2284 lbs across three spec lines.
In HP Spec Lines, Honda CRX 1.5 (88-91), change weight as follows: "2245 2175 *2301 2229 **2357 2284"
SRF3 Update SRF Rain / Brake Rule
#34706 from Robey Clark · Rule change · TB 23-09 (2023-09 Fastrack)
neutralSRF rain/brake light now requires Super Bright LEDs Inc. P/N PT-STRB-R24 with specific connector and rain light switch.
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain light."
SRF3 Update SRF Brake Light Rule v1
#34853 from Robey Clark · Rule change · TB 23-10 (2023-10 Fastrack)
neutralSRF requires Super Bright LEDs P/N PT-STRB-R24 rain/brake light with strobing capability and specific wiring.
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."
HP Request to Review Z3 2.5 Spec Line
#35073 from Tim Schreyer · Rule change · TB 24-01 (2024-01 Fastrack)
slowerEP BMW Z3 2.5L weight increases to 2500 lbs, 2563 lbs with turbo, 2625 lbs with supercharger.
In EP spec line, BMW Z3 2.5L, change weight as follows: "2450 2500 *2511 2563 **2573 2625"
HP Parity in HP
#35138 from Kendall Jones · Rule change · TB 24-01 (2024-01 Fastrack)
fasterHP Sprite/Midget Mk I–IV, Mk 1500 compression ratio raised to 12.0:1 at Prep Level 1/2.
In HP Spec Line, Austin-Healey Sprite Mk I, II, III, IV / MG Midget Mk I, II, III, IV & 1500, Prep Level 1/2, change Notes section as follows: "Compression ratio limited to 11 12.0:1"
unclearT1-GT4 batch adjustments: five cars lighter, two heavier, restrictors and ECU maps changed, five models now eligible for Runoffs.
In GCR, Section 9.1.9.1.A.T., change as follows: "Tires- Tires must conform to GCR section 9.3.TIRES and als o must conform to spec line requirements. DOT approved tires are permitted. Slicks conforming to the spec line are permitted." In Touring 1 - Homologated Cars Spec Lines, 4100- BMW M2 ClubSport Racing, change Must Conform To as follows: "Tires conforming to SRO TCX rules allowed. Must meet factory specs." In Touring 1 - Homologated Cars Spec Lines, 4120- Ford Mustang FP350S 2017, change as follows: Must Conform To: "Tires conforming to Trans Am SGT tire rules allowed Must meet factory specs." Chassis Notes: "VIN not required. Additional permitted allowances: DOT tires required. Other consumables are open, alternate
Show 40 more lines
driveshaft permitted, aftermarket wheels and fuel cell per Touring category rules permitted. Shocks conforming to T1 rules permitted. Alternative rear toe links permitted." In T1-GT4 Spec Lines, change Chassis Notes as follows: Aston Martin Vantage AMR GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)** Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Audi R8 GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." BMW M4 GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Chevrolet Camaro GT4-R: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Ford Mustang GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Maclaren 570S GT4: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Mercedes AMG GT4: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Porsche 718 Cayman GT4 CS MR: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Porsche 718 GT4 RS Club-sport: "Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." Toyota Supra GR GT4: "**NOT YET ELLIGIBLE FOR RUNOFFS COMPETITION (Q.2)**Slick tires conforming to IMSA GT4 or SRO GT4 specs are permitted." In T1-GT4 Spec Lines, change as follows: Aston Martin Vantage AMR GT4: Weight: “3575 3490” Performance Control: “SRO power level ECU Map 3 IMSA Map id 11” Chevrolet Camaro GT4-R: Weight: “3375 3435” Performance Control: “63 62mm” Ford Mustang GT4: Weight: “3550 3535” Performance Control: “63 71mm SRO compliant restrictor IMSA ECU Cal” Maclaren 570S GT4: Weight: “3450 3250” Performance Control: “SRO 2019 BOP ECU map SRO Rest 1” Mercedes AMG GT4: Weight: “3450 3470” Performance Control: “Power level 2 map 5” Porsche 718 Cayman GT4 CS MR: Weight: “3200 3250” Performance Control: “54 53.7mm” Toyota Supra GR GT4: Weight: “3350 3315”
In EP spec line, Triumph GT6, make the following change in the Notes section: "Two (2) 1.75” auto-type carburetors @ 1970 40 lbs. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, May use 5 speed gearbox w/o overdrive. Three (3) Weber 40mm DCOE w/28mm venturi on individual runner manifold @ 2020 lb."
SRF3 SRF / SRF3 Rule Updates
#35268 from Robey Clark · Rule change · TB 24-01 (2024-01 Fastrack)
neutralSRF adds brake duct and pedal extension rules, rear shift cable clamp option, camber limit to 5.0°, radiator opening height 3.5" ±0.5", and P2 engine restrictor changes.
In SRF, GCR section 9.1.8.D.1.H, add the following: "NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part # P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad "anti-rattle" clips must be removed." In SRF, GCR section 9.1.8.D.1.V, add the following:
Show 23 more lines
"ii. Rear SADEV shift cable aluminum two-piece style clamp may be used. The P/N WM302007A clamp must serve no other purpose." In SRF, GCR section 9.1.8.D.1.X.k, add the following: "Negative camber shall must not exceed 5.0 degrees absolute maximum front and rear." In SRF, GCR section 9.1.8.D.1.AA.b, add the following: "2. Height of the radiator opening vertical surface 3 1/2“ +/- 1/2"." P2 Engine Table B.1 2008 and older Stock Suzuki, Yamaha, Honda, BMW 38.5mm P2 Engine Table B.2 Not required P2 Engine Table B.3 38.5mm Modified Engine 950 lbs. 1005cc max P2 Engine Table B.1 2008 and older 37mm P2 Engine Table B.2 Not required P2 Engine Table B.3 39mm Stock Engine 1050 lbs.
HP Honda S2000 throttle body
#35272 from Aaron Johnson · Rule change · TB 24-01 (2024-01 Fastrack)
fasterEP Honda S2000 fuel injected throttle body inside diameter increases from 62mm to 64mm.
In EP spec line, Honda S2000, make the following changes to its spec line: Fuel Injected Equipped Throttle Body Inside Diameter: "62 64" Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .500”. An adaptor plate can be used to mount the 62mm throttle body from '00-05 to the '06-09 intake manifold. The adaptor plate can be no more than 1.25" thick, and its bore must not exceed the "Fuel Injected Equipped Throttle Body Inside Diameter" maximum spec of 64mm."
HP Front Header/Nose Panel Alternate Material For 84-87 CRX
neutralHP Honda CRX/Si 84-87 front header/nose panel may use alternate material if appearance remains stock.
In HP Spec Lines, Honda CRX/Si (84-87), in Notes, make the following change: "Compression ratio limited to 11.0:1, Valve lift limited to .390”. The front header/nose body panel can be replaced by a replica which may be constructed of an alternate material provided its appearance remains stock."
HP Correction within Triumph TR8 Spec Line
#35315 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)
neutralEP Triumph TR8 dry sump allowance moved from carburetor line to notes section.
In EP spec line, Triumph TR8 (78-81), move the "Dry sump allowed" wording to the appropriate location as follows: Carburetor. No. & Type: “Zenith Stromberg carbs or fuel injection. Dry sump is allowed.” Notes: “Comp. Ratio limited to 12.0:1, Valve lift limited to .500”. Dry sump is allowed.”
HP Correction to EP 924S/944 Spec Line
#35317 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)
neutralEP Porsche 944/924S 2.5L and 2.7L weight minimums corrected: 2479cc to 2306/2363 lbs, 2681cc to 2358/2415 lbs.
In EP spec line, Porsche 944/924S 2.5L (2V) / 2.7L (2V) (83-89), change Weight as follows:
A specification table follows in the original; it is not shown here.
HP Review Classification of HP Mazda 2
#35318 from Production Committee · Rule change · TB 24-01 (2024-01 Fastrack)
neutralT1 NEW class removes 23 spec lines including Acura NSX, Ferrari, Porsche 996, Nissan Z cars, and others; Porsche 997 spec line 1680 expiration removed.
In GCR Contents, change as follows: "9.1.9.1 TOURING (T1) CATEGORY NEW T1 NEW" In GCR, Section 9.1.9.1.Touring (T1) NEW Category Specifications, change as follows: "9.1.9.1.Touring (T1) NEW Category Specifications" In T1 NEW Spec Lines, change as follows: "9.1.9.1.A T1 NEW Spec Lines" "T1 NEW"
Show 26 more lines
In T1 NEW Spec Lines, delete the following Spec Lines in their entirety: "Acura NSX (Spec Line 1000) Acura NSX Turbo (Spec Line 1010) Acura NSX Turbo World Challenge (Spec Line 1020) Audi TTRS (GTS 2011 Spec) (Spec Line 1040) Dodge Viper ACR/ACR-X (Spec Line 1360) Ferrari 360 (Spec Line 1400) Ferrari 430 (Spec Line 1410) Ferrari 430 Challenge (Spec Line 1420) Mazda MX-5 (06-15) (Spec Line 1520 and 1530) Mazda RX-7 (Spec Line 1540) Nissan GTR (Spec Line 1550) Nissan 350/370Z (Spec Line 1560) Nissan 370Z Supercharged (Spec Line 1570) Nissan 350Z (Spec Line 1580) Nissan 350Z/370Z (Spec Line 1590) Porsche Cayman/S/GTS (05-15) (Spec Line 1600, 1610 and 1620) Porsche Cayman GTS (2011) (Spec Line 1630) Porsche 928 S4 Porsche 928 GTS-R (Spec Line 1640) Porsche 996 (Spec Line 1650) Porsche 996 TT OEM (Spec Line 1660) Subaru WRX, WRX STI (05-2020) (Spec Line 1700) Toyota Celica All-Trac (Spec Line 1710) Toyota Supra MK4 (Spec Line 1720)" In T1 NEW Spec Lines, Porsche 997, change Spec Line Number as follows: "1680 *Spec line Expires 12/23*"
In HP Spec Lines, delete the following redundant spec lines in their entirety: Spec line #10 - VW Rabbit Cabriolet 1780 Spec line #3 - VW Scirocco 1588 Spec line #4 - VW Scirocco 1780 (8-valve) (83-88) Spec line #5 - VW Scirocco 1588
neutralHP Honda CRX/Si 84-87 plastic panels can be replaced with replica alternate material if stock appearance maintained.
In HP spec line "Honda CRX/Si (84-87)", make the following change to the Notes section: "The plastic OE front header/nose body panel, lower rocker side-skirt, and lower door cap panel can be replaced by a replica, which may be constructed of an alternate material, provided its appearance remains stock."
neutralNissan 300ZX 84-89 classified to EP at 2550 lbs minimum, 2960cc 6-cyl SOHC, fuel injection, 12.0:1 compression limit, 0.500" valve lift limit.
In EP Spec Lines, classify Nissan 300ZX (84-89), as follows:
A specification table follows in the original; it is not shown here.
HP RX7 1993 and Up Request In EP Spec Lines, classify
#36031 from Edward Zabinski · Rule change · TB 24-06 (2024-06 Fastrack)
neutralMazda RX-7 92-97 newly classified EP Prep Level 2 at 2200–2310 lbs with 13B 6-port rotary engine.
Mazda RX-7 (92-97) as follows:
A specification table follows in the original; it is not shown here.
SRF3 SRF3 Alternator Pulley Update In
#36095 from Robey Clark · Rule change · TB 24-06 (2024-06 Fastrack)
fasterSRF3 alternator pulley minimum weight reduced from 12 oz to 11 oz.
SFR3, GCR section 9.1.8.D.2.H.17, change as follows: "Alternator Pulley: P/N G902130, or P/N G902130A, or P/N G902131 (six row). 12 11 oz minimum weight."
HP Clean-up Multiple EP RX-8 Spec Lines In EP
#36156 from Production Committee · Rule change · TB 24-06 (2024-06 Fastrack)
neutralEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.
Spec Lines, make the following changes to the two Mazda RX-8 spec lines. Remove spec line entirely: Mazda RX-8 (04-11) Remove the wording "alternate": Mazda RX-8 (04-11)(alternate) Spec Mazda (SM/SMX) None.
neutralHP Volkswagen Golf and Jetta 85-92 track correction: front 1537mm (60.5in), rear 1529mm (60.2in).
In HP Spec Lines, change Track (F/R)mm/(in.) as follows: Volkswagen Golf (GTI, GT, GL) (85-92): "2 1537/1529 (60.5/60.2)" Volkswagen Jetta (GLI, GL) (85-92): "2 1537/1529 (60.5/60.2)"
SRF3 Update Rain Tire Rule and Hoosier Decal Placement
#36436 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)
slowerSRF wet tires: P185/60R13 H20/W2 option removed; P185/65R13 W2 front now required with P205/60R13 W2 rear.
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used. OR Front – Hoosier P/N 46101 P185/65R13 W2 Rear – Hoosier P/N 46105 P205/60R13 W2
Show 8 more lines
1. It is forbidden to regroove tires. 2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for violation will be the loss of qualifying times and/or the disqualification of race results. 3. Hoosier SRF/SRF3 Decal Placement: Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises."
SRF3 Update to Letter 36619 with new Hoosier Contingency Decal Info
#36624 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)
neutralSRF Hoosier decal requirement reduced from four decals in specific locations to three decals with simpler placement rules.
In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows: "Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
SRF3 Update SRF3 Air Filter Rule
#36681 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
unclearSRF3 air filter rule removes K&N RC-9160 option, leaving only P/N WM301020 allowed.
In SRF, GCR section 9.1.8.D.2.H.23, change as follows: "Air Filter: P/N WM301020 or K&N RC-9160"
SRF3 Update SRF Brake Rotor Thickness
#36687 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
slowerSRF brake rotor minimum thickness increases from 12.20mm to 13.25mm, Wilwood vented rotor P/N 800065.
In SRF, GCR section 9.1.8.D.1.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."
SRF3 Hoosier Tire Decal Placement
#36739 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)
neutralSRF3 Hoosier logo placement changes from four decals to three decals in different locations.
In SRF, GCR section 9.1.8.D.2.B, change as follows: "Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."
fasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.
In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1275cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1" In HP Spec Lines, Austin-Healey Sprite MkI, II, III, IV MG Midget (ALL) - Level 2 - 1098cc, change Notes as follows: "(Effective 11/1/2024) Compression ratio limited to 11 12.0:1"
HP Request for Classification of 1989-1994 Suzuki Swift GT 16V Twin
neutralBMW M4 GT4 (G82) added to T1 GT4 at 3525 lbs minimum weight with Red power stick control.
In T1 GT4 Spec Lines, SL#4030, change as follows: Model: "BMW M4 GT4 (F82)" Performance Control: "Gold power stick Red power stick" In T1 GT4 Spec Lines, classify BMW M4 GT4 (G82) as follows:
A specification table follows in the original; it is not shown here.
T1 Alt. Clutch Allowance
#36606 from Hugh Stewart · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT1 Spec Lines now permits 5.5 inch clutch in Engine Notes.
In T1 Spec Lines, SL# 1050, change add to Engine Notes the following: "5.5 inch clutch permitted."
T1 BOP Changes Need Updates
#36667 from Joe Rainey · Rule change · TB 24-12 (2024-12 Fastrack)
fasterT1 GT4 Spec Line 4020 restrictor opens from 44mm to 45mm, minimum weight drops to 3400 lbs.
In T1 GT4 Spec Lines, Spec Line 4020, change as follows: Performance Control: Power level 2020, 44mm 45mm SRO compliant restrictor" Min. Weight with driver (LBS): "3550 3400"
T1 Request Ford Performance Darkhorse R in T1
#37136 from Christopher Childs · Rule change · TB 24-12 (2024-12 Fastrack)
neutralMustang Darkhorse R added to T1 homologated cars at 3,250 lbs minimum with 305/315 tires, ineligible for Runoffs until 3 Super Tour events.
In T1-Homologated Cars Spec Line, classify Mustang Darkhorse R (Mustang Challenge) as follows: T1 – Homologated Cars
A specification table follows in the original; it is not shown here.
T1 Car Mods for T1 Corvette under line item 1150
#37173 from Thomas Napolitano · Rule change · TB 24-12 (2024-12 Fastrack)
neutralT1 Corvette may roll or flatten wheel opening lips for tire clearance; plastic fenders may remove lips if edge thickness matches basic material.
In GCR, Section 9.1.9.1.A.2,, add the following: "It is permitted to roll under or flatten any interior lip on the wheel opening for tire clearance. Cars with plastic/composite fenders may remove any interior wheel opening lip, but the resulting material edge shall be no thinner than the basic fender material thickness. Non-metallic inner fender liners may be removed. Vents may be added to fenders."
HP MINI Cooper Spec Line Correction - Rear Brake Rotor Diameter
#37176 from Robert Bax · Rule change · TB 24-12 (2024-12 Fastrack)
neutralHP Mini Cooper 02-06 rear brake rotor increases from 239/9.4 mm/in to 259/10.2.
In HP Spec Lines, Mini Cooper (02-06), change Brakes Std.mm/(in.) as follows: "(F) 276/(10.9) Vented Disc (R) 239/(9.4) 259/(10.2) Solid Disc"
Applies to Mini Cooper on this page: Tom Tuttle
T1 Increased Bore Throttle Bodies for E46 M3 S54 Engine
#37273 from Mark Pfeffer · Rule change · TB 24-12 (2024-12 Fastrack)
fasterT1 E46 M3 S54 can now use Dinan Throttle Body #D760-3400 on 3.250L engine.
In T1 Spec Lines, E46 M3 Spec Line # 1050, add to Engine Notes the following: "Dinan Throttle Body #D760-3400 allowed on the 3.250L."
HP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line
#37119 from Tim Schreyer · Rule change · TB 25-01 (2025-01 Fastrack)
fasterEP BMW 325i/is E30 (84-91) weight reduced 50–52 lbs across three spec lines to 2150, 2204, 2258.
In EP SPEC LINES, BMW 325i/is (E30) (84-91), change Weight as follows: "2200 2150 *2255 2204 **2310 2258"
HP Request to Update 1988-1991 Civic to Match 1988-1991 CRX
fasterHP Honda Civic 1.5 88-91 weight reduced to 2175 lbs base, 2229 lbs with one asterisk, 2284 lbs with two asterisks.
In HP SPEC LINES, Honda Civic 1.5 (88-91), change Weight as follows: "2245 2175 *2301 2229 **2357 2284"
T1 T1 Parity Compared to GT4
#37170 from Tony Ave · Rule change · TB 25-02 (2025-02 Fastrack)
slowerT1 Mustang gains 125 lbs to 3600, restrictor shrinks 65mm to 60mm. Corvette gains 50 lbs to 3500, restrictor shrinks 70mm to 67mm. BMW deleted.
In T1 Spec Lines, change Weight and Restrictor Required as follows: Mustang - Spec Line 1430 Weight: "3475 3600" Restrictor Required: "65mm 60mm - FPR" Corvette Spec Line 1190 Weight: "3450 3500" Restrictor Required: "70mm 67mm - Flat Plate" In T1 Spec Lines, delete Spec Line BMW # 1190 in its entirety.
T1 Clarification of Request Approval #37273
#37399 from Mark Pfeffer · Rule change · TB 25-02 (2025-02 Fastrack)
unclearT1 E46 M3 Spec Line 1050 allows VAC Motorsports throttle body VAC-TB-S54 on 3.250L engine instead of Dinan.
In T1 Spec Lines, E46 M3 Spec Line # 1050, change Engine Notes as follows: "Dinan Throttle Body #D760-3400 VAC Motorsports #VAC-TB-S54 allowed on the 3.250L."
#37466 from Michael Unger · Rule change · TB 25-03 (2025-03 Fastrack)
fasterEP Honda S2000 1997cc base loses 75 lbs to 2375; 2157cc base loses 60 lbs to 2450.
In EP, Spec Lines make the following weight changes:
A specification table follows in the original; it is not shown here.
HP Mazda 1999 Miata 1.8L
#37488 from Joe Carr · Rule change · TB 25-03 (2025-03 Fastrack)
fasterEP Mazda MX-5/Miata 99-05 minimum weight drops to 2100 lbs, 2153 lbs with power adder, 2205 lbs with two adders.
In EP Spec Lines, make the following weight change: Mazda MX-5 /Miata (99-05): "2150 2100 *2204 2153 **2258 2205"
HP MINI Cooper (07-13) Spec Line Correction: Errors and Omissions
#37560 from Robert Bax · Rule change · TB 25-03 (2025-03 Fastrack)
slowerHP Mini Cooper 07-13 engine corrected to DOHC; valve lift limit reduced to 0.390 inches.
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), change as follows: Engine Type: "4 Cyl SOHC DOHC" Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
unclearT1 Mustang Spec 1430 restrictor opens 60mm to 65mm; Spec 1460 weight rises to 3500 lbs, restrictor 70mm; Corvette 1190 restrictor opens 67mm to 70mm; BMW 1090 restrictor narrows 40mm to 35mm; BMW 1100 weight rises to 3350 lbs.
In T1 Spec Lines, change Weight, Restrictor Required and/or Notes as follows: Mustang - Spec Line 1430: Restrictor Required: "60mm 65mm - FPR" Mustang - Spec Line 1460: Weight: "3425 3500" Restrictor Required: "70mm - FPR" Corvette Spec Line 1190: Restrictor Required: "67mm 70mm - Flat Plate"
Show 5 more lines
BMW - Spec Line 1090: Required Restrictor: "(2) X 40mm 35mm diameter hole inlet restrictor plate required" Chassis Notes: "This spec line is set to expire 12/31/25." BMW - Spec Line 1100: Minimum Weight: "3150 3350”
HP Request for Classification of Chevrolet Spark
#37755 from Kristian Smith · Rule change · TB 25-04 (2025-04 Fastrack)
neutralChevrolet Spark 16-22 classified HP Pre at 1850 lbs minimum weight, fuel injected, 1399 cc.
In HP Spec Lines, classify the Chevrolet Spark (16-22):
A specification table follows in the original; it is not shown here.
HP Request to Lower Ford Festiva Minimum Weight to 1600 LBS
fasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.
In HP Spec Lines "Ford Festiva (88-93)" change as follows: Weight: "1700 1600 *1743 1640 **1785 1680" Notes: "Compression ratio limited to 10.5 11.0:1. Valve lift limited to .450”."
SRF3 Driver Safety & Comfort
#37966 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)
neutralSRF drivers with disabilities may modify seat and controls for safety and comfort with approval and logbook notation.
In SRF, GCR section 9.1.8.D.1.D, add the following: "f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
SRF3 Update SADEV transmission specs
#37992 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)
neutralCadillac CT4-V Blackwing added to T1 Spec Line 1115, 3564cc, 3750 lbs minimum weight.
In T1 Spec Lines, classify Cadillac CT4-V Blackwing as follows:
A specification table follows in the original; it is not shown here.
T1 Acceptance of Porsche 981 GT4 Clubsport into T1
#36664 from John Brown · Rule change · TB 25-05 (2025-05 Fastrack)
neutralPorsche 981 GT4 Clubsport added to T1 as spec line 4085, minimum weight 3100 lbs with driver.
In T1-GT4 Spec Lines, classify Porsche 981 GT4 Clubsport as follows:
A specification table follows in the original; it is not shown here.
T1 Request to Restore T1 Honda S2000 to Proper Weights
#37644 from David Mead · Rule change · TB 25-05 (2025-05 Fastrack)
fasterT1 Honda S2000 minimum weight reduced from 2950 lbs to 2900 lbs.
In T1 Spec Lines, Honda S2000, Spec Line 1530, change as follows: Minimum Weight: "2950 2900" Chassis Notes: "This spec line is set to expire as of 12/31/2025 if not represented in Majors competition in 2025."
T1 DCT Transmission in E46
#37964 from Matt Spicuzzi · Rule change · TB 25-05 (2025-05 Fastrack)
neutralT1 BMW E46 M3 permits BMW #GS7D36SG aftermarket sequential transmission in SL# 1060 and 1070.
In T1 Spec Lines, BMW E46 M3, add to Chassis Notes the following: SL# 1060: "BMW #GS7D36SG transmission permitted as an aftermarket sequential option." SL# 1070: "BMW #GS7D36SG transmission permitted as an aftermarket sequential option."
Applies to BMW M3 on this page: Ian Barberi
T1 Reduce E92 M3 Minimum Weight to 3050
#38092 from Shane Brown · Rule change · TB 25-05 (2025-05 Fastrack)
fasterT1 BMW M3 E92 minimum weight reduced to 3300 lbs.
In T1 Spec Lines, BMW M3 E92 (08-13), Spec Line 1100, change Min. Weight as follows: "3350 3300"
fasterT1 Mustang Darkhorse R gets 315 front and rear tyres, loses 500 lbs minimum weight to 3600.
In T1 Spec Lines, Mustang Darkhorse R (Mustang Challenge) Spec Line- 4119, change as follows: Tire size: "305 315 (f) 315(r)" Performance Control: "TBD" Min. Weight with driver (LBS): "10.5 (f) 11 (r) 3600" Chassis Notes: "Must conform to Mustang Challenge Rules. Tires conforming to Mustang Challenge rules are permitted. **This car is not eligible for the Runoffs until it has competed in 3 Super Tour events.**"
HP Base Weight Adjustment for H-Production X1/9 Spec Lines
#38255 from Matthew Brannon · Rule change · TB 25-06 (2025-06 Fastrack)
fasterHP Fiat X-1/9 base weights reduced 50–53 lbs across 1300 and 1500 spec lines.
In HP Spec Lines, change Weight as follows: Fiat X-1/9 & Bertone1500: “1790 1740 *1835 1784 **1880 1827” Fiat X-1/9 1300: “1650 1600 *1691 1640 **1733 1680” Fiat X-1/9 1300: “2060 2010” Fiat X-1/9 1500: “1950 1900”
Effective 9/1/25 in SRF, GCR section 9.1.8.D.1.V.ff, add the following: "SRF3 Oil Cooler, P/N G480503 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual." Effective 9/1/25 in SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 must be used as delivered with no machining of any kind. Minimum thickness 13.25mm (0.522”). The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038
Show 11 more lines
may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind; maximum of one spring per caliper. 1. Hawk Blue pads P/N 801993 only 2. Wilwood Vented Rotor P/N 800065 only, as delivered, with no machining of any kind. Minimum thickness 13.25mm (0.522") 3. Wilwood universal caliper Kit P/N 1180008 as delivered, caliper only P/N 800038; Wilwood knock back spring P/N 800045 may be used as delivered, with no machining of any kind, and only one spring per caliper 4. Renault caliper rubber bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185A 5. Renault caliper piston may be replaced with P/N 1196184 vented piston as delivered, with no machining of any kind 6. Girling .750" Master Cylinder P/N 880358 as delivered, with no machining of any kind 7. Wilwood .750" Master Cylinder P/N 880357 as delivered, with no machining of any kind 8. Tilton .750" Master Cylinder P/N 880360 as delivered, with no machining of any kind"
SRF3 Add HD Oil Cooler
#38979 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)
neutralSRF3 adds HD Oil Cooler P/N G1148500 as alternative to standard cooler P/N G480503.
In SRF, GCR section 9.1.8.D.1.V.ff, change as follows: "SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
HP HP Plymouth Arrow spec omission
#38995 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralHP Plymouth Arrow transmission max speeds clarified to 4 or 5.
In HP Spec Lines, Plymouth Arrow (76-80), add the following wording to Trans. Speeds(max): "4 or 5"
HP Add Wheel Diameter to Appendix G
#39008 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP wheel diameter added to Appendix G as absolute maximum specification.
In Appendix G.2.3, change as follows: "Rim width and diameter are is absolute maximums."
HP Add TB ID tolerance to general Prod rules
#39009 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
neutralEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.
In GCR, Section 9.1.5.E., change as follows: 9.1.5.E.1.b.4: "The inside dimensions of the throttle body casting/housing (as measured at the throttle butterfly) must remain stock (tolerance of +/-.25mm), but the throttle body can otherwise be ported and polished." 9.1.5.E.2.b.4: "The inside dimensions of the throttle body casting/housing and all dimensions of the throttle butterfly must remain stock (tolerance of +/-.25mm)."
HP Please Lower Weight of 280Z
#38871 from Matthew Miller · Rule change · TB 25-09 (2025-09 Fastrack)
fasterEP Nissan 280Z minimum weight reduced from 2560 to 2400 lbs.
In EP Spec Lines, Nissan 280Z, change Weight (lbs) as follows: "(Effective 11/1/2025) 2560 2400 *2624 2460 **2688 2520"
HP Miata Weight Adjustment Follow Up
#38949 from Don Tucker · Rule change · TB 25-10 (2025-10 Fastrack)
fasterEP Mazda MX-5 1.8L 90-97 weight reduced to 2125 lbs from 2150 lbs.
In EP Spec Lines, Mazda MX-5 / Miata 1.8L (90-97), Effective 11/1/2025 make the following weight change: "2150 2125"
HP Weight Break for 1098 Midget / Sprite
#38970 from Kendall Jones · Rule change · TB 25-10 (2025-10 Fastrack)
In HP Spec Lines, Austin-Healey Sprite/Midget 1098cc, Effective 11/1/2025make the following weight change: "1630 1550"
HP HP Volvo 142 spec omission
#38994 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".
In HP Spec Lines, Volvo 142/142E P-1800 Engine, Effective 11/1/2025 add the following wording to Notes: "Comp. Ratio limited to 12.0:1. Valve lift limited to .425”."
HP HP Mini DOHC 1.6
#38996 from Production Committee · Rule change · TB 25-10 (2025-10 Fastrack)
slowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".
In HP Spec Lines, Mini Cooper (07-13) (includes 09-15 convertible and 12-15 Coupe), Effective 11/1/2025 make the following changes to the Notes: "Compression ratio limited to 11.0:1, Valve lift limited to .450”.390"."
HP Add to Rabbit description
#39019 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.
In FP Spec Lines, make the following spec line correction: "Volkswagen Rabbit (Includes Convertible Cabriolet)" In HP Spec Lines, make the following spec line correction: "Volkswagen Rabbit 1588 (Includes Cabriolet)" "Volkswagen Rabbit 1715 (Includes Cabriolet)" "Volkswagen Rabbit 1780 (Includes Cabriolet)"
HP Clean-up 9.1.5.E.7e
#39025 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.
In GCR, Section 9.1.5.E.7., change as follows: "e. Cars fitted with rear drum brakes, can convert to rear disc brakes without penalty. Note that the “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes stock, from converting to rear disc brakes under this rule. When converting from rear drum brakes to rear disc brakes: 1. Rear brake rotors must be solid and can be no larger in diameter than the largest permitted front brake rotor, as defined on the vehicle’s spec line. 2. Rear calipers and mounting brackets are unrestricted but must be made of a ferrous or aluminum material. The standard and alternate brake listings on a vehicle’s specification line, does not prohibit a car that was fitted with rear drum brakes as stock
Show 3 more lines
from converting to rear disc brakes under this rule. 3. The “Brakes Std.” and “Brakes Alt.” listings on a vehicle’s spec line do not prohibit a car that was fitted with rear drum brakes as stock from converting to rear disc brakes under this rule."
HP Add TB size to Ford Mustang (94-98) Spec Line
#39130 from Production Committee · Rule change · TB 25-11 (2025-11 Fastrack)
neutralEP Ford Mustang (94-98) fuel injected throttle body inside diameter specified at 60.
In EP Spec Lines, Ford Mustang (94-98) add the following to the Fuel Injected Equipped Throttle Body Inside Diameter column: "60"
HP Request to Re-Classsify Datsun SPL-311 to HP from FP
#39116 from Robert Heatwole · Rule change · TB 25-12 (2025-12 Fastrack)
neutralDatsun SPL-311 newly classified to HP at 2050 lbs with 1595cc OHV iron engine and specified carburetors.
In HP Spec Lines, classify Nissan/Datsun SPL 311 as follows:
A specification table follows in the original; it is not shown here.
HP TR2 Notes E&O
#39180 from Anthony Parker · Rule change · TB 25-12 (2025-12 Fastrack)
unclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.
In EP Spec Lines, Triumph TR2, 3, 3A, 4, 4A, TR4, TR4A, IRS, make the following change to the Notes: "Front apron assembly may be made of alternate material. Three (3) Weber 40 DCOE on IR manifold with 28mm chokes @ 1990 lbs. Laycock overdrive, may use 5 speed gearbox without overdrive."
HP Balance of Power
#39187 from Jim Simaras · Rule change · TB 25-12 (2025-12 Fastrack)
slowerEP BMW Z3 2.5L restrictor reduced 52mm to 50mm, weight increased to 2550 lbs base; five other BMW models get smaller restrictors.
In EP Spec Lines, make the following changes to Restrictors: BMW Z3 2.5L: "52mm 50mm Flat Plate Intake Restrictor" BMW Z3 2.8L (97-00): "55mm 53mm Flat Plate Intake Restrictor" BMW 328i/is E36 (96-99): "58mm 55mm Flat Plate Intake Restrictor" BMW 328i/ci E46 (01-06): "58mm 55mm Flat Plate Intake Restrictor" BMW 325i/is (E46) (01-06): "56mm 53mm Flat Plate Intake Restrictor" BMW 325is M-Technic (1994): "56mm 53mm Flat Plate Intake Restrictor" BMW 325i/is E-36 (92-95): "56mm 53mm Flat Plate Intake Restrictor"
Show 4 more lines
In EP Spec Lines, BMW Z3 2.5L, change Weight as follows: "2500 2550 *2563 2614 **2625 2678"
HP Alternative BOP Request for 84-87 Honda CRX/Civic
#39223 from Bill Lamkin · Rule change · TB 25-12 (2025-12 Fastrack)
fasterHP Honda Civic and CRX models get wider 13-inch wheels: 6 to 7 inches.
In HP Spec Lines, change Wheels as follows: Honda Civic: "13 x 6 7" Honda Civic DX (92-95): "13 x 6 7" Honda Civic/Si (84-87): "13 x 6 7" Honda Civic 1.5 (88-91): "13 x 6 7" Honda CRX/Si (84-87): "13 x 6 7" Honda CRX 1.5(88-91): "13 x 67"
T1 Keep S2000 Classification
#39344 from David Mead · Rule change · TB 25-12 (2025-12 Fastrack)
unclearUnable to summarize: letter states intent but provides no actual rule changes to S2000 specification.
unclearT1 Spec Line restrictor changes from 70mm flat plate to unspecified new specification.
In T1 Spec Line, Spec line # 1132, change Restrictor as follows: "70mm - Flat Plate"
HP Request to Reclassify BMW 2002 Into H Production
#39567 from Jonathan Kinberg · Rule change · TB 26-01 (2026-01 Fastrack)
neutralBMW 2002 newly classified to H Production at 2350 lbs with 1990cc iron block, 40 DCNF carburetor, 11.0:1 compression.
In HP Spec Lines, classify BMW 2002, as follows:
A specification table follows in the original; it is not shown here.
HP Triumph Spitfire 1296cc Compression Ratio Increase to 12:1
#39589 from Neil Verity · Rule change · TB 26-02 (2026-02 Fastrack)
fasterHP Triumph Spitfire 1296cc compression ratio increases from 11.0 to 12.0:1.
In HP Spec Lines, make the following spec line changes: Triumph Spitfire: Carburetion "Valves: (I) 33.0/(1.30) (E) 29.7/(1.17) Comp. ratio 11.0 12.0:1, Valve lift .450” Trans. Speeds: 4" Triumph Spitfire Mk. III & IV 1500: Carburetion
In T1 Spec Lines, reinstate Spec Line # 1139, Chevrolet Corvette C6 (05-13) Includes Z51, GrandSport, Z06, Z06 Carbon, as follows: Max Displ: "LS1, LS6 OEM" Min Weight: "3200" Required Restrictor: "70mm"
What the rules allowed changed as listed; this does not say what any particular car ran.