Quickest here:STU 1:50.913 Tony Rivera, Cal Club 2026 qualifying · P2 1:37.278 Tim Day Jr, Cal Club 2026 qualifying
STUP2solid race · dashed qualifying · slower is lower
STUP2solid race · dashed qualifying · each class's best lap as a share of STU's at the same event (the reference class, changeable above); 100% is level, higher is quicker
Event
STU
P2
Qual best
Race best
Trap
Qual best
Race best
Trap
vs STU
% of STU
Cal Club 2026 CALCL262026-02-21
1:50.913Tony Rivera · fastest of 6 · top 5 within 14.1s-4.488s (-3.89%)
1:52.737Tony Rivera · fastest of 7 · top 5 within 7.7s-0.903s (-0.79%)
135.2Tony Rivera+21.8 mph (+19.3%)
1:37.278Tim Day Jr · only car
1:39.758Tim Day Jr · only car
155.4Tim Day Jr
-12.979squal -13.635s
88.5%qual 87.7%
17 rule changes (STU: 17)7 weight · 3 tyres & wheels · 2 cars added · 2 induction · 1 engine · 2 wording · STU Mazda MZR (LF, L3, L5) Turbo classified; Jack Spania Racing 70 mm intake manifold and Fab9 Tuning bottom-mount turbo kit approved. · STU 36mm restrictor allows 2830 lbs (up 10 lbs from 2820); 37mm allows 2980 lbs (down 5 lbs from 2985). · STU cars over 3150 lbs lose 275-tire option with 2% weight adder. · STU Honda K20 and K24 engines lose 2% minimum weight penalty. · STU Honda K24 engine swap weight increases by 2% effective November 1, 2025. · STU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs. · STU-TCR tire width increases to 275 with weight adder raised from 100 to 150 pounds. · STL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs. · STU 2.8-3.2L N/A engines now allow 245 max tire width; over 3150 lbs may run 275 with 2% weight penalty. · STU Mazda MZR may use Goodwin 61-2510 or Gato Performance 31972 intake manifold. · STU Honda JDM H23a added, 2259cc displacement, minimum weight per Chart, must meet ST engine regulations. · STU wheel width rules clarified: cars ≤2,850 lbs max 8 inches, cars >2,850 lbs max 9 inches. · STU Spec Line GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tire options clarified with weight adjustments. · STU BMW N54/N55 3.0L classified at Chart +3% minimum weight; N54 twin turbo not allowed. · STU Mini Cooper S SC supercharger pulley diameter reduced from 2.285 to 2.185. · STU Honda K20C1 Turbo I4 exempted from 3% DI weight adder in Spec Lines Table A. · STU GT3U minimum weight increases 150 to 250 pounds.showhide
STU Request for Permission on Aftermarket Turbo Kit and Intake #39529cars addedfasterSTU Mazda MZR (LF, L3, L5) Turbo classified; Jack Spania Racing 70 mm intake manifold and Fab9 Tuning bottom-mount turbo kit approved.
STU Turbo Inlet Restrictor Table #38961inductionslowerSTU 36mm restrictor allows 2830 lbs (up 10 lbs from 2820); 37mm allows 2980 lbs (down 5 lbs from 2985).
STU 275 Tire Rule #38983tyres & wheelsslowerSTU cars over 3150 lbs lose 275-tire option with 2% weight adder.
STU STU Honda Engine weight penalty #39375weightfasterSTU Honda K20 and K24 engines lose 2% minimum weight penalty.
STU Non-Homologated Engine Swaps - Specifically K24A2 w/ Honda CRZ #38746weightslowerSTU Honda K24 engine swap weight increases by 2% effective November 1, 2025.
STU Lotus Weight Reduction E&O #38919weightfasterSTU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs.
STU STU-TCR Adjustments #38723tyres & wheelsslowerSTU-TCR tire width increases to 275 with weight adder raised from 100 to 150 pounds.
STU Lotus Weight Reduction #38772weight -50 lbsfasterSTL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs.
STU 2.8-3.2L N/A Engine Allowances #38007tyres & wheelsunclearSTU 2.8-3.2L N/A engines now allow 245 max tire width; over 3150 lbs may run 275 with 2% weight penalty.
STU 2006-2015 Mazda Miata Intake Manifold #38422wordingneutralSTU Mazda MZR may use Goodwin 61-2510 or Gato Performance 31972 intake manifold.
STU Requesting Approval of the JDM Honda h23a #38489cars addedneutralSTU Honda JDM H23a added, 2259cc displacement, minimum weight per Chart, must meet ST engine regulations.
STU Wheel Size Inconsistency #38018wordingneutralSTU wheel width rules clarified: cars ≤2,850 lbs max 8 inches, cars >2,850 lbs max 9 inches.
STU Table C: STU-GT3U Clarification #38268weightfasterSTU Spec Line GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tire options clarified with weight adjustments.
STU BMW N54/N55 Engine Allowance Follow Up #37447engineneutralSTU BMW N54/N55 3.0L classified at Chart +3% minimum weight; N54 twin turbo not allowed.
STU STU Mini Cooper pulley size clarification re: letter #36980 #37717inductionfasterSTU Mini Cooper S SC supercharger pulley diameter reduced from 2.285 to 2.185.
STU Question About a Weight Modifier #37782weightfasterSTU Honda K20C1 Turbo I4 exempted from 3% DI weight adder in Spec Lines Table A.
STU Increase Minimum Weight #37919weight +100 lbsslowerSTU GT3U minimum weight increases 150 to 250 pounds.
Cal Club 2025 CALCL252025-02-22
1:55.401Wilson Powell · fastest of 4 · top 4 within 8.7s
1:53.640Rylan Hazelton · fastest of 5 · top 5 within 8.0s
113.3Rylan Hazelton
132 earlier rule changes on record, in force before Cal Club 2025 (from 2019)17 engine · 17 induction · 16 cars added · 11 weight · 8 aero · 4 tyres & wheels · 58 wording · 1 other · STU Audi 1.8T wagon deleted; Porsche 944 1800 weight to Chart, turbo inlet restrictor removed. · STU-GT3 reclassified as STU-GT3U effective January 1, 2026. · STU GT3 TCR gains 275-width tire option with 100 lb weight penalty, but not in A compound. · P2 2000cc Pinto engine car minimum weight set to 1335 lbs. · STL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval. · STU BMW N54/N55 turbo inlet restrictors now required per GCR definition; turbo swapping prohibited. · STU Mini Cooper S SC 1900 restricts to 2.565 diameter pulley; 2100 allows 2.285 diameter pulley. · STU RWD turbo cars no longer required to reduce restrictor by 1 mm from table. · P2 Spec ECU engine modifications clarified: oil system, ECU, and exhaust unrestricted only. · P2 FIA Group CN spec notes clarified: Series changed to Challenge, documentation requirement moved to online link. · STU Mini Cooper S SC: alternate LEAP OMICRON hood scoop LEP-OMICRON3 permitted. · STU BMW S54 B32 OEM now permits dry sump oiling system. · STL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems. · P2 AMAC modified engine range clarified to 2008 and older stock engines only, restrictor 38mm, weight 1025 lbs. · P2 Suzuki GSX-R1000 07/08 engine crankcase may swap to GSX-S1000 16/19 part #11301-04840. · P2 Table 1 corrects engine date ranges and brand specifications for Stock and Modified engines across multiple car models. · Toyota GR Cup and GR86 Cup (2022-) newly classified in STU at 2700 lbs with 2387 cc engine. · P2 side body height requirement clarified: outermost surface between wheel openings must equal front axle centerline height. · P2 closed cockpit single seat cars now prohibited unless specifically allowed in Table 1. · P2 engine table wording updated; redundant effective date language removed. · P2 motorcycle engines: 2011+ Kawasaki restrictor reduced to 34mm, minimum weight raised to 1100 lbs; 2009+ other brands weight raised to 1100 lbs. · STU Mazda BP5A classified at 1839 cc maximum displacement, 2023-04-01. · STU minimum weight chart updated: 2450cc to 2595lbs, 2600cc to 2710lbs. · Sebeco NP01-EVO and Elan NP01 Mazda 2.0L MZR added to P2, 1600 lb minimum, no restrictor required. · P2 Radical SR3/SR4/Cup/Club Sport/Pro-Sport/PR6 removes assisted shifting requirement across all spec lines. · P2 chassis rules clarified to allow composite materials in non-fully-composite construction; anti-intrusion panel attachment standardized; Stohr and converted F600 cars added with specific allowances. · Unable to summarize: the change to P2 Engine Table Spec Line B.1 is not detailed in the provided text. · STU Mazda 13B Turbo classified, streetport only, stock turbos prohibited, alternatives allowed. · STU OEM louver vents now exempt from vent count and 200 square inch allowance. · STU 2400cc non-4-valve engines gain 9% base weight reduction; DI turbo prep limits removed. · STU normally-aspirated 2976–3200 cc single-throttle engines lose 10% base engine weight reduction. · ST redundant language removed from balance shaft and pulley modification rules. · P2 chassis construction rules clarified: fully composite or partially composite requiring composite for mobility allowed; partial composite must roll without composite parts. · P2 classification wording cleaned up in GCR section 9.1.8.C and Contents. · STU cars that qualified for 9 inch wheels in 2021 may continue through 2022 only. · STU splitter definition clarified: must be single-plane with no vertical deviations, attached to lowest front point. · P2 Oldsmobile cam rules clarify aftermarket manufacturer requirements; wording only. · STU BMW S52B32 minimum weight drops 90 lbs to 3110; max displacement cut to 3152 cc. · STU BMW S50B32 Euro classified at 3201 cc displacement, 3300 lbs minimum weight. · ST engine swap origin country requirement changes from North America to the United States for case-by-case approval. · STU Honda CRX (84-91) and Civic Del Sol (93-97) ineligible for front wheel drive weight reductions. · STU vehicles at or over 2950 lbs base weight may use 9 inch wide wheels instead of 8.0 inch maximum. · STU minimum weights reduced: 2450cc to 2596 lbs, 2500cc to 2635 lbs, 2550cc to 2675 lbs. · P2 adds Beasley B2 spec line with 1350 lbs, Mazda 12A, 40.5mm venturi, 16.5in wing. · P2 wing specs correct terminology from 'cord' to 'chord' for 16.5in single or dual element wings. · P2 Converted F5 cars reclassified as Converted F500 cars; suspension must comply with F500 requirements, minimum width 55 inches. · STU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed. · STU Audi A4 1.8T minimum weight fixed at 3050 lbs, VF30 turbo with 35mm restrictor now required only. · STL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements. · P2 motorcycle engines increase to 1505cc max, two-stroke to 1205cc max; automotive engines gain 50 lbs minimum weight to 1350. · STU engines may delete balance shafts and plug openings; alternate pulleys allowed for timing belt or chain operation only. · STU hood vents allowed to include louvers within 200 sq. inch area. · P2 Control Area definition narrowed; aerodynamic attachments and vertical structures like turning vanes now prohibited. · STU adds Honda K23 with 2354cc displacement and minimum weight per chart, K24 block allowed with K23 internals and head. · STU Honda K23 internals rule relaxed to require only K23 crankshaft, allowing other internal modifications. · STL and STU piston engines clarified: intake manifold and cylinder head porting remains free. · P2 Engine Table Spec Line B.1 changed effective 1-1-22, details not provided in excerpt. · P2 Control Area definition clarified: floor extensions and aerodynamic attachments on bottom or top side now explicitly included. · P2 CN Honda K20A-FD2 engine rebuild rules clarified: machining prohibition replaced with specific restrictions on balancing, porting, polishing, valve jobs, cylinder honing. · Converted F5 cars in P2 minimum width reduced to 55 inches from F5 spec. · P2 clarifies minimum body width requirement between front and rear wheels for Ralt RT40, RT41, Swift 008, 014. · STU fender flare wording clarified: exterior contour of any wheel opening may not change opening size, location or shape from side view. · STU Mazda 12A Bridge Port Miata weight reduced from 2550 lbs to 2350 lbs. · P2 tonneau covers now allowed to meet minimum dimensions; equipment attachment requirements clarified. · P2 multiple chassis models remove effective dates from Table 1 specifications. · P2 engines limited to 4 valves per cylinder maximum across all three spec lines. · STU fender flare rules clarified: maximum 2 inches, must cover tire contact patch from above, cannot alter body configuration or wheel opening geometry. · STU Honda S2000 allows F20/F22 K24 crankshaft with chart weight for achieved displacement. · ST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions. · P2 adds new spec line for 2-cycle 3-cylinder engine up to 820cc with 10 front and 14-15 rear wheel width. · STL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs. · ST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment. · STU Porsche PDK automatic transmission limited to 8 forward speeds instead of torque converter restriction. · STU Mazda 13B Street Port 2400 removes choke location restriction, allows auto-type 2bbl with dual-Y manifold. · STU driveshaft and half-shaft materials change from OEM-type to steel or aluminum. · STU Mazda 13B Street Port classified at 2400 lbs minimum weight, replacing peripheral and bridge port variants. · P2 Honda K20A-FD2 intake restrictor reduced from 55mm to 50mm, making cars faster. · ST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch. · P2 rear wing requirements clarified: standard wing 6×12 inches, end plates 14-inch square; alternate 110cm width wing 9×18 inches, end plates 14×18 inches. · STU fender flare rules reworded: up to 2" per corner allowed with 1% weight penalty total. · STL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments. · STL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change. · STU request for alternate intake manifold denied; no rule change issued. · GT3 and STU add Borg-Warner EFR6258 to approved turbocharger list. · STU large displacement turbo engines limited by GCR turbo list; non-turbo trim suggested as more competitive. · STU sequential shifters referred to Board of Directors for approval; no change implemented yet. · Elan NP01 classified in P2 Table 1 as Spec Line car with 2000cc displacement and P2 Engine Table restrictor. · STU Mazda 13B Bridge Port and Street Port engines added with 2550 and 2250 lbs minimum weights respectively. · P2 Enterprises Sports Racer adds 55mm flat plate intake restrictor Part # WM303013 as alternative to SIR. · P2 Enterprise Sports Racer 2.3L engine now requires SIR or Flat Plate restrictor sized in 0.5mm increments. · STU Honda S2000 adds HKS Supercharger kits 12001-AH006 and 12001-AH010 as allowed. · STU Lotus Elise Cup R and SC models, plus Exige SC, gain 100–200 lbs minimum weight. · STU Volkswagen GTI/GLI MK5 and Jetta Mk4 may install turbo inlet restrictor in OEM turbo inlet housing. · STU Honda K20C1 Turbo I4 restrictor reduces from 36mm to 35mm. · STU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs. · STU Porsche 944 now permits VW/Audi 1.8L and 2.0L turbo engines as alternates. · P2 fly-by-wire throttle control wording clarified: stock ECUs with drive-by-wire must activate original throttle shaft mechanism. · STU vehicles over 2951 lbs base weight may use 9 inch wide wheels, up from 2950 lbs. · STU turbocharged engines now use base weight instead of minimum weight, with 3% DI increase applied to base weight. · P2 adds BMW to motorcycle-based engine options in 4-cycle line alongside Kawasaki, Suzuki, Yamaha, Honda. · STU cars with manual OEM throttle bodies may convert to OEM electronic throttle body of same inner diameter. · P2 Honda K20A-FD2 non-composite chassis must use 55mm flat plate intake restrictor at 1500 lbs minimum weight. · P2 motorcycle engines: Stock restrictor 36.5mm to 35mm, modified 37.5mm to 34mm; B.5 restrictor 37.5mm to 33mm. All weights increase 25 lbs. · STU wing assembly wording corrected: no part higher than roof height. · P2 cars limited to power application on maximum two wheels, effective 2019-07-01. · STU Nissan SR20DET removes -2mm penalty in Table B. · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · P2 Enterprise minimum weight increases to 1375 lbs; peak horsepower of sealed ESR engine reduced per CRB specification. · STU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement. · STU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · STU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock. · STU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body. · STU suspension rules clarified: alternate components from same manufacturer moved from section E to section D. · STU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold. · STU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules. · TCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019. · STU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight. · P2 stock engine restrictor shrinks to 35.0mm and weight rises to 1025 lbs; modified engine restrictor to 34.0mm, weight to 1125 lbs; line B.5 restrictor to 33.0mm, weight to 1185 lbs. · P2 Line A.1 restrictor reduced from 40mm to 38mm. · Honda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork. · STU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances. · STU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed. · STU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10. · STU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options. · STU World Challenge car weight calculation method removed; new basis unclear from text provided. · STU AWD cars no longer required to reduce restrictor 1 mm from table. · STU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each. · P2 Spec Line cars now allow 1345cc Hayabusa stock engines at 1050 lbs with 30mm restrictor. · P2 Group CN Honda K20A-FD2 55mm restrictor implementation delayed from 1/1/2019 to 3/1/2019. · P2 Honda K20A-FD2 in CN chassis must use stock intake manifold with 64mm throttle body and 55mm restrictor at 1500 lbs minimum weight. · STU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR.showhide
STU Audi 1.8t Wagon STU Table B #36685cars addedfasterSTU Audi 1.8T wagon deleted; Porsche 944 1800 weight to Chart, turbo inlet restrictor removed.
STU Merger GT3 to STU #37486wordingneutralSTU-GT3 reclassified as STU-GT3U effective January 1, 2026.
STU GT3 TCR Tire allowance #37494tyres & wheelsslowerSTU GT3 TCR gains 275-width tire option with 100 lb weight penalty, but not in A compound.
P2 2000 cc Pinto Engine Car Weight #37187weightslowerP2 2000cc Pinto engine car minimum weight set to 1335 lbs.
STU Request to Remove Miata Hubs from General category #37138wordingneutralSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
STU BMW N54/N55 Engine Allowance #37146inductionslowerSTU BMW N54/N55 turbo inlet restrictors now required per GCR definition; turbo swapping prohibited.
STU R53 15% Pulley Request #36980inductionslowerSTU Mini Cooper S SC 1900 restricts to 2.565 diameter pulley; 2100 allows 2.285 diameter pulley.
STU RWD Turbo Disadvantage #36255inductionfasterSTU RWD turbo cars no longer required to reduce restrictor by 1 mm from table.
P2 E&O - Correct FIA Group CN spec line notes #35900wordingneutralP2 FIA Group CN spec notes clarified: Series changed to Challenge, documentation requirement moved to online link.
STU Letter #35397 addendum #35453wordingneutralSTU Mini Cooper S SC: alternate LEAP OMICRON hood scoop LEP-OMICRON3 permitted.
STU S54 Drysump #35464wordingneutralSTU BMW S54 B32 OEM now permits dry sump oiling system.
STU ST Electric-Assisted Steering Systems #35066wordingneutralSTL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems.
P2 E&O - Clarify B.1 modified engine range in AMAC spec lines #35225wordingneutralP2 AMAC modified engine range clarified to 2008 and older stock engines only, restrictor 38mm, weight 1025 lbs.
P2 Replacement Engine Crankcase for 07/08 Suzuki GSX-R1000 Engines #35340engineunclearP2 Suzuki GSX-R1000 07/08 engine crankcase may swap to GSX-S1000 16/19 part #11301-04840.
P2 Correct Table 1 for Engine Date Range Specifications #35182wordingneutralP2 Table 1 corrects engine date ranges and brand specifications for Stock and Modified engines across multiple car models.
STU 2022 Toyota GR Cup for STU #34449cars addedneutralToyota GR Cup and GR86 Cup (2022-) newly classified in STU at 2700 lbs with 2387 cc engine.
P2 Clarify minimum side body height requirement #34143wordingneutralP2 side body height requirement clarified: outermost surface between wheel openings must equal front axle centerline height.
P2 Clarify closed cockpit single seat car allowance #34144wordingneutralP2 closed cockpit single seat cars now prohibited unless specifically allowed in Table 1.
P2 Remove redundant effective date language and update engine table #34012wordingneutralP2 engine table wording updated; redundant effective date language removed.
P2 E&O - Correct dimensional equivalents #34038engineslowerP2 motorcycle engines: 2011+ Kawasaki restrictor reduced to 34mm, minimum weight raised to 1100 lbs; 2009+ other brands weight raised to 1100 lbs.
STU Alternate OEM Miata Intake Manifold #33827wordingneutralSTU Mazda BP5A classified at 1839 cc maximum displacement, 2023-04-01.
STU E&O STU NA Weight Chart. #33737weightfasterSTU minimum weight chart updated: 2450cc to 2595lbs, 2600cc to 2710lbs.
P2 Request to Classify Sebeco NP01 #33378cars addedneutralSebeco NP01-EVO and Elan NP01 Mazda 2.0L MZR added to P2, 1600 lb minimum, no restrictor required.
P2 Radical spec line clarifications #33485wordingneutralP2 Radical SR3/SR4/Cup/Club Sport/Pro-Sport/PR6 removes assisted shifting requirement across all spec lines.
P2 E&O original class intent #33519wordingneutralP2 chassis rules clarified to allow composite materials in non-fully-composite construction; anti-intrusion panel attachment standardized; Stohr and converted F600 cars added with specific allowances.
P2 Update Engine Table Spec Line B.1 #33608engineunclearUnable to summarize: the change to P2 Engine Table Spec Line B.1 is not detailed in the provided text.
STU Request Mazda 13 B turbo #32668cars addedneutralSTU Mazda 13B Turbo classified, streetport only, stock turbos prohibited, alternatives allowed.
STU Hood Vents and Intercooler Scoops #32733aerofasterSTU OEM louver vents now exempt from vent count and 200 square inch allowance.
STU Non 4 valve weight reduction removed #32808enginefasterSTU 2400cc non-4-valve engines gain 9% base weight reduction; DI turbo prep limits removed.
STU Error in new minimum weight table when combined with other text #32711engineslowerSTU normally-aspirated 2976–3200 cc single-throttle engines lose 10% base engine weight reduction.
STU Redundant Language in May GCR #32713wordingneutralST redundant language removed from balance shaft and pulley modification rules.
P2 E&O Clarification of Chassis Construction Requirements #32469wordingneutralP2 chassis construction rules clarified: fully composite or partially composite requiring composite for mobility allowed; partial composite must roll without composite parts.
P2 Clean up P2 wording #32525wordingneutralP2 classification wording cleaned up in GCR section 9.1.8.C and Contents.
STU Opposed to the Proposed STU Weight Chart #32381wordingneutralSTU cars that qualified for 9 inch wheels in 2021 may continue through 2022 only.
STU Clarification request for GCR 9.1.4.D.3.a Splitter Definition #32414wordingneutralSTU splitter definition clarified: must be single-plane with no vertical deviations, attached to lowest front point.
P2 After Market to Aftermarket #32373wordingneutralP2 Oldsmobile cam rules clarify aftermarket manufacturer requirements; wording only.
STU Request Adjustment to Min Weight for STU BMW E36 M3 (95-99) #31535weight -90 lbsfasterSTU BMW S52B32 minimum weight drops 90 lbs to 3110; max displacement cut to 3152 cc.
STU BMW E36 M3 Canadian (North American) S50B32 engine #31866cars addedneutralSTU BMW S50B32 Euro classified at 3201 cc displacement, 3300 lbs minimum weight.
STU Engine Swap Origin Country #32209wordingneutralST engine swap origin country requirement changes from North America to the United States for case-by-case approval.
STU CRX/Civic Del Sol #32214weightslowerSTU Honda CRX (84-91) and Civic Del Sol (93-97) ineligible for front wheel drive weight reductions.
STU Error correction #32383tyres & wheelsfasterSTU vehicles at or over 2950 lbs base weight may use 9 inch wide wheels instead of 8.0 inch maximum.
STU Single TB Weight Modifiers Add to Chart #32393weightfasterSTU minimum weights reduced: 2450cc to 2596 lbs, 2500cc to 2635 lbs, 2550cc to 2675 lbs.
P2 Add spec line for Beasley B2 #32147cars addedneutralP2 adds Beasley B2 spec line with 1350 lbs, Mazda 12A, 40.5mm venturi, 16.5in wing.
P2 E&O Table 1 spec line wing terminology #32148wordingneutralP2 wing specs correct terminology from 'cord' to 'chord' for 16.5in single or dual element wings.
P2 E&O class name #32196wordingneutralP2 Converted F5 cars reclassified as Converted F500 cars; suspension must comply with F500 requirements, minimum width 55 inches.
STU Single TB Weight Modifiers #31449weightfasterSTU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed.
STU Request to Remove A4 1.8t from STU Spec Line Tables #31465weightslowerSTU Audi A4 1.8T minimum weight fixed at 3050 lbs, VF30 turbo with 35mm restrictor now required only.
STU Improved Touring Tires #32063tyres & wheelsneutralSTL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements.
P2 E&O Engine section #31969enginefasterP2 motorcycle engines increase to 1505cc max, two-stroke to 1205cc max; automotive engines gain 50 lbs minimum weight to 1350.
STU Request Allowance for Balance Shaft Delete in STU #31434enginefasterSTU engines may delete balance shafts and plug openings; alternate pulleys allowed for timing belt or chain operation only.
STU Request Louvers in hood vents #31916aeroneutralSTU hood vents allowed to include louvers within 200 sq. inch area.
P2 E&O letter #31539 – Control Area definition #31783aeroslowerP2 Control Area definition narrowed; aerodynamic attachments and vertical structures like turning vanes now prohibited.
STU Request to Add Honda K23 Spec Line #30682cars addedneutralSTU adds Honda K23 with 2354cc displacement and minimum weight per chart, K24 block allowed with K23 internals and head.
STU RE: Aug FT letter 30682 #31060enginefasterSTU Honda K23 internals rule relaxed to require only K23 crankshaft, allowing other internal modifications.
STU Throttling Device Clarification #31323wordingneutralSTL and STU piston engines clarified: intake manifold and cylinder head porting remains free.
P2 BoP adjustment effective 1-1-22 #31538wordingunclearP2 Engine Table Spec Line B.1 changed effective 1-1-22, details not provided in excerpt.
P2 E&O clarification of "Control Area" definition #31539wordingneutralP2 Control Area definition clarified: floor extensions and aerodynamic attachments on bottom or top side now explicitly included.
P2 P2 CN Engine Rebuild Clarification #31000wordingneutralP2 CN Honda K20A-FD2 engine rebuild rules clarified: machining prohibition replaced with specific restrictions on balancing, porting, polishing, valve jobs, cylinder honing.
P2 F5 P2 Conversion #30856aerofasterConverted F5 cars in P2 minimum width reduced to 55 inches from F5 spec.
P2 Clarify minimum body width requirement #30859wordingneutralP2 clarifies minimum body width requirement between front and rear wheels for Ralt RT40, RT41, Swift 008, 014.
STU STU Fender flares #30696wordingneutralSTU fender flare wording clarified: exterior contour of any wheel opening may not change opening size, location or shape from side view.
STU Request weight reduction for 12A bridgeport motor in Miata #30751weight -200 lbsfasterSTU Mazda 12A Bridge Port Miata weight reduced from 2550 lbs to 2350 lbs.
P2 E&O tonneau cover provision in cockpit opening section #30459wordingneutralP2 tonneau covers now allowed to meet minimum dimensions; equipment attachment requirements clarified.
P2 Remove effective dates in Table 1 #30468wordingneutralP2 multiple chassis models remove effective dates from Table 1 specifications.
P2 E&O Maximum Valves Per Cylinder #30560engineneutralP2 engines limited to 4 valves per cylinder maximum across all three spec lines.
STU Request for Fender Flare Clarification #30375wordingneutralSTU fender flare rules clarified: maximum 2 inches, must cover tire contact patch from above, cannot alter body configuration or wheel opening geometry.
STU Provision for Interchangeable Engine Components Already Allowed #30342engineunclearSTU Honda S2000 allows F20/F22 K24 crankshaft with chart weight for achieved displacement.
STU ST Oil Coolers E&O Correction to 9.1.4.2.H #30388wordingneutralST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions.
P2 Add a new spec line for a 2-cycle, 3-cylinder engine up to 820cc #30272cars addedneutralP2 adds new spec line for 2-cycle 3-cylinder engine up to 820cc with 10 front and 14-15 rear wheel width.
STU Super Touring Alternate Miata Hubs #30345wordingneutralSTL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs.
STU Brake Component Relocation #29990wordingneutralST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment.
STU Porsche PDK #30081wordingneutralSTU Porsche PDK automatic transmission limited to 8 forward speeds instead of torque converter restriction.
STU Reference Letter #29333 Proposed STU 13B Spec Line Changes #30086inductionfasterSTU Mazda 13B Street Port 2400 removes choke location restriction, allows auto-type 2bbl with dual-Y manifold.
STU Drive Shaft Request #30087wordingneutralSTU driveshaft and half-shaft materials change from OEM-type to steel or aluminum.
STU 13B Rules Adjustment #29333cars addedslowerSTU Mazda 13B Street Port classified at 2400 lbs minimum weight, replacing peripheral and bridge port variants.
P2 Balance of Performance adjustments effective 01-01-2021 #29822inductionfasterP2 Honda K20A-FD2 intake restrictor reduced from 55mm to 50mm, making cars faster.
STU Request clarification on wing measurement #29640aeroneutralST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch.
P2 E&O clarification of P2 rear wing requirements #29205aeroneutralP2 rear wing requirements clarified: standard wing 6×12 inches, end plates 14-inch square; alternate 110cm width wing 9×18 inches, end plates 14×18 inches.
STU Request for Advanced Aero Rule Wording Clarification. #29124wordingneutralSTU fender flare rules reworded: up to 2" per corner allowed with 1% weight penalty total.
STU Minimum Weight Determination #27695wordingneutralSTL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments.
STU ST Gurney flap Wicker clarification #29012wordingneutralSTL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change.
STU Request for Alternate Intake Manifold #26514wordingneutralSTU request for alternate intake manifold denied; no rule change issued.
STU Request for Addition to GT3 Approved Turbo List #27576wordingneutralGT3 and STU add Borg-Warner EFR6258 to approved turbocharger list.
STU Request BoP for my Car #29004wordingneutralSTU large displacement turbo engines limited by GCR turbo list; non-turbo trim suggested as more competitive.
STU Sequential Shifters in STU #29031wordingneutralSTU sequential shifters referred to Board of Directors for approval; no change implemented yet.
P2 Classify Elan NP01 in P2 Table 1 #28812cars addedneutralElan NP01 classified in P2 Table 1 as Spec Line car with 2000cc displacement and P2 Engine Table restrictor.
STU Rotary Help #27833cars addedneutralSTU Mazda 13B Bridge Port and Street Port engines added with 2550 and 2250 lbs minimum weights respectively.
P2 SCCA Enterprises ESR / P2 engine restrictor testing #28669engineneutralP2 Enterprises Sports Racer adds 55mm flat plate intake restrictor Part # WM303013 as alternative to SIR.
P2 Add ESR inlet restrictor #27869inductionslowerP2 Enterprise Sports Racer 2.3L engine now requires SIR or Flat Plate restrictor sized in 0.5mm increments.
STU Request to approve Honda S2000 HKS supercharger #27281enginefasterSTU Honda S2000 adds HKS Supercharger kits 12001-AH006 and 12001-AH010 as allowed.
STU Request BoP on the Lotus #27637weight +100 lbsslowerSTU Lotus Elise Cup R and SC models, plus Exige SC, gain 100–200 lbs minimum weight.
STU Turbo Inlet Restrictor On MK5 Volkswagen #27704inductionslowerSTU Volkswagen GTI/GLI MK5 and Jetta Mk4 may install turbo inlet restrictor in OEM turbo inlet housing.
STU Honda K20C1 removal #27732inductionslowerSTU Honda K20C1 Turbo I4 restrictor reduces from 36mm to 35mm.
STU Change GM LNF 2.0 Allowance to LSJ Engine for Viable STL 2.0 #27884engineslowerSTU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs.
STU Alternate Engine for Porsche 944 #28259engineunclearSTU Porsche 944 now permits VW/Audi 1.8L and 2.0L turbo engines as alternates.
P2 Request for Fly by Wire Rule Wording Change #28247wordingneutralP2 fly-by-wire throttle control wording clarified: stock ECUs with drive-by-wire must activate original throttle shaft mechanism.
STU Please Modify the STU Wheel Size Rule for Clarity #27694weightfasterSTU vehicles over 2951 lbs base weight may use 9 inch wide wheels, up from 2950 lbs.
STU Turbo Engine Cars Base Weight #28032wordingneutralSTU turbocharged engines now use base weight instead of minimum weight, with 3% DI increase applied to base weight.
P2 Request for addition of BMW Engine in P2 Engine Table #27821cars addedneutralP2 adds BMW to motorcycle-based engine options in 4-cycle line alongside Kawasaki, Suzuki, Yamaha, Honda.
STU Request for an electronic throttle body #27342wordingneutralSTU cars with manual OEM throttle bodies may convert to OEM electronic throttle body of same inner diameter.
P2 Update Engine Table Line E notes #27414inductionslowerP2 Honda K20A-FD2 non-composite chassis must use 55mm flat plate intake restrictor at 1500 lbs minimum weight.
P2 Update P2 Engine Table spec lines to reflect 3/1/2019 #27254inductionslowerP2 motorcycle engines: Stock restrictor 36.5mm to 35mm, modified 37.5mm to 34mm; B.5 restrictor 37.5mm to 33mm. All weights increase 25 lbs.
STU Request to correct E&O advanced aerodynamics #27290wordingneutralSTU wing assembly wording corrected: no part higher than roof height.
P2 E&O Transmissions #27006otherslowerP2 cars limited to power application on maximum two wheels, effective 2019-07-01.
STU Remove -2mm penalty from SR20DET Nissan #26982enginefasterSTU Nissan SR20DET removes -2mm penalty in Table B.
STU Request clarification for manifold and throttle in STU #27004inductionfasterSTU alternate intake manifolds now allowed case-by-case instead of prohibited.
P2 Request to restrict all cars #26246weightslowerP2 Enterprise minimum weight increases to 1375 lbs; peak horsepower of sealed ESR engine reduced per CRB specification.
STU Request to clarify afterrmarket side skirts exhaust exit #26814wordingneutralSTU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement.
STU Wheel Flare wording #26872wordingneutralSTU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty.
STU Request Ride Height Clarification #26597wordingneutralSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld.
STU Request to Use Japanese Mazda 13b Intake Manifold #25790inductionfasterSTU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock.
STU Request Alternate Intake for Mazda MZR In a Rear Wheel Drive App. #26352inductionunclearSTU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body.
STU E&O Suspension #26424wordingneutralSTU suspension rules clarified: alternate components from same manufacturer moved from section E to section D.
STU Revisit B20 VTEC #26530enginefasterSTU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold.
STU Move Flared Fenders to STU Advanced Aero #26564aeroneutralSTU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules.
STU TCA Civic SI E&O #26606tyres & wheelsslowerTCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019.
STU S54 Spec line #26620wordingneutralSTU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight.
P2 Change Engine Table Lines B.1 & B.5 #25777inductionslowerP2 stock engine restrictor shrinks to 35.0mm and weight rises to 1025 lbs; modified engine restrictor to 34.0mm, weight to 1125 lbs; line B.5 restrictor to 33.0mm, weight to 1185 lbs.
P2 Change Line A.1 restrictor size #26429inductionslowerP2 Line A.1 restrictor reduced from 40mm to 38mm.
STU Request to Class Assignment for 2017 Civic #24287cars addedneutralHonda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork.
STU Request to run E46 3246cc in STU #25126cars addedneutralSTU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances.
STU Engine Classification for Rotary #25564wordingunclearSTU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed.
STU K24/K20 Head Swap Clarification/Amendment #25899wordingneutralSTU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10.
STU Request to Classify 12a Bridge Ported Rotary Engine #25985cars addedneutralSTU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options.
STU World Challenge Car Eligibility #26387wordingunclearSTU World Challenge car weight calculation method removed; new basis unclear from text provided.
STU Request a phone call for discussion regarding weight #26398inductionfasterSTU AWD cars no longer required to reduce restrictor 1 mm from table.
STU Advanced Aero E&O #26413aeroneutralSTU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each.
P2 Request to Allow 1345cc Hayabusa Engines for Spec Line P2 Cars #25595enginefasterP2 Spec Line cars now allow 1345cc Hayabusa stock engines at 1050 lbs with 30mm restrictor.
P2 Change CN inlet restrictor implementation date #25816wordingneutralP2 Group CN Honda K20A-FD2 55mm restrictor implementation delayed from 1/1/2019 to 3/1/2019.
P2 Clarify Honda K20A-FD2 parts requirement #25950inductionslowerP2 Honda K20A-FD2 in CN chassis must use stock intake manifold with 64mm throttle body and 55mm restrictor at 1500 lbs minimum weight.
STU Request to Equalize Direct Injected Turbo Cars #24890cars addedneutralSTU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR.
Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of STU" is the class's best as a share of STU's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when STU's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.