Quickest here:FF 1:51.118 Eric Poulsen, Cal Club 2025 race · GTX 1:49.596 Rob Scholl, Cal Club 2025 race · FA 1:35.792 Greg Labadie, Cal Club 2026 qualifying
FFGTXFAsolid race · dashed qualifying · slower is lower
FFGTXFAsolid race · dashed qualifying · each class's best lap as a share of FF's at the same event (the reference class, changeable above); 100% is level, higher is quicker
Event
FF
GTX
FA
Qual best
Race best
Trap
Qual best
Race best
Trap
vs FF
% of FF
Qual best
Race best
Trap
vs FF
% of FF
Cal Club 2026 CALCL262026-02-21
1:53.098Edward Erlandson · fastest of 2+1.054s (+0.94%)
1:54.741Edward Erlandson · fastest of 2+3.623s (+3.26%)
133.7Edward Erlandson+19.0 mph (+16.5%)
1:54.892Moze Cowper · only car
1:55.330Moze Cowper · only car+5.734s (+5.23%)
146.0Moze Cowper+29.6 mph (+25.4%)
+0.589squal +1.794s
100.5%qual 101.6%
1:35.792Greg Labadie · only car-3.750s (-3.77%)
1:37.275Greg Labadie · only car-2.623s (-2.63%)
163.8Greg Labadie+36.4 mph (+28.6%)
-17.466squal -17.306s
84.8%qual 84.7%
13 rule changes (FF: 3, GTX: 3, FA: 7)3 cars added · 3 tyres & wheels · 2 engine · 2 induction · 1 aero · 2 wording · FA Pro Mazda: lower intake manifold now unrestricted, throttle body raised to 80mm, wing height must not exceed 99cm, bodywork width must not exceed 132cm. · FA MZR gains alternate Noor P/N 0088-8-00 intake manifold with AT Power runners as option to Elan or Mazda Speed Elite. · FA Formula 1000 motorcycle-based engine loses maximum compression ratio 14.5:1 limit. · FA Formula 1000 allows carbon fiber external panels, forward-facing gaps, raises floor to 125mm, adds eight 75×125mm rub blocks, expands diffuser to 110cm with 75mm radius transitions. · FF clarifies alternative tire eligibility for cars homologated 1989 or earlier with rocker arm or outboard suspension on all four corners. · GTX Misc Table 4 adds RCR T70 Coupe with 2200 lbs minimum weight, no restrictor specified. · FA class adds USF Pro 2000 car eligibility for Formula Atlantic racing. · FA Ligier JS F3 front tires may be Hoosier 43363 240/580R13 MS, rear 43368 300/590R13 MS. · GTX Ligier LMP3 now allows any normally aspirated LS Chevrolet engine. · FF adds rocker arm and outboard suspension cars optional bias ply and VFF tires; removes front-as-rear rule, adds mixing restrictions. · GTX Porsche GT2 RS Clubsport classified with factory specifications required at all race events. · FA Formula Renault 2.0 (10-17) spec notes clarified: engine sealed, manual compliance required, tire choice unrestricted, no alterations except repairs. · FF allows older cars with rocker arm or outboard suspension to use bias ply slicks or VFF tires instead of radials.showhide
FA Pro Mazda Classification and Performance Enhancement Proposal #39411inductionfasterFA Pro Mazda: lower intake manifold now unrestricted, throttle body raised to 80mm, wing height must not exceed 99cm, bodywork width must not exceed 132cm.
FA Alternate Intake Manifold for MZR #38223inductionunclearFA MZR gains alternate Noor P/N 0088-8-00 intake manifold with AT Power runners as option to Elan or Mazda Speed Elite.
FA Engine Compression Rule Change Request #39302enginefasterFA Formula 1000 motorcycle-based engine loses maximum compression ratio 14.5:1 limit.
FA Change Formula 1000 allowances #39608aerofasterFA Formula 1000 allows carbon fiber external panels, forward-facing gaps, raises floor to 125mm, adds eight 75×125mm rub blocks, expands diffuser to 110cm with 75mm radius transitions.
FF Formula F Alternative Tire Rule Proposed Clarifications #39281wordingneutralFF clarifies alternative tire eligibility for cars homologated 1989 or earlier with rocker arm or outboard suspension on all four corners.
GTX Please Consider Adding a Spec Line to GTX Table 4 for the RCR T70 #39470cars addedneutralGTX Misc Table 4 adds RCR T70 Coupe with 2200 lbs minimum weight, no restrictor specified.
FA Re-Consider USF Pro 2000 Car for Formula Atlantic Class #38783cars addedneutralFA class adds USF Pro 2000 car eligibility for Formula Atlantic racing.
FA Ligier JS F3 Tire Choice #38434tyres & wheelsneutralFA Ligier JS F3 front tires may be Hoosier 43363 240/580R13 MS, rear 43368 300/590R13 MS.
GTX Ligier P3 LS Swap #38164engineunclearGTX Ligier LMP3 now allows any normally aspirated LS Chevrolet engine.
FF Page 228, FF tire rule 9.1.1.10.e #38251tyres & wheelsneutralFF adds rocker arm and outboard suspension cars optional bias ply and VFF tires; removes front-as-rear rule, adds mixing restrictions.
GTX Request to Classify Porsche GT2 RS Clubsport #37972cars addedneutralGTX Porsche GT2 RS Clubsport classified with factory specifications required at all race events.
FA Update Formula Renault 2.0 spec line notes #37853wordingneutralFA Formula Renault 2.0 (10-17) spec notes clarified: engine sealed, manual compliance required, tire choice unrestricted, no alterations except repairs.
FF Formula F Proposal to Invite Older Cars Via a Tire Rule Change #37802tyres & wheelsfasterFF allows older cars with rocker arm or outboard suspension to use bias ply slicks or VFF tires instead of radials.
Cal Club 2025 CALCL252025-02-22
1:52.044Eric Poulsen · only car
1:51.118Eric Poulsen · only car
114.7Eric Poulsen
1:49.596Rob Scholl · only car
116.4Rob Scholl
-1.522s
98.6%
1:39.542Greg Labadie · only car
1:39.898Greg Labadie · only car
127.4Greg Labadie
-11.220squal -12.502s
89.9%qual 88.8%
112 earlier rule changes on record, in force before Cal Club 2025 (from 2019)29 cars added · 8 induction · 7 engine · 6 weight · 2 aero · 2 tyres & wheels · 1 removed · 57 wording · FA adds Tatuus F.3 T-318 or FR-19 as spec line car in Table 2 for Formula Regional European Championship. · TA2 rear wing height rule clarified: OEM aerodynamic devices exempt from peak-of-roof requirement. · FF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs. · FF Honda Fit allows Fast Forward 0.25mm oversize pistons PN FF800-110 as alternative; piston diameter spec clarified to 2.8835 inches. · FF VTEC activation valve must function; EGR blanking plate rule clarified with Fast Forward part numbers. · GT2-ST Acura NSX minimum weight raised to 3000 lbs, restrictor increased to 45mm TIR. · GT1, GT2, GT3, GTL, GTX rear spoiler maximum surface area limit of 295.0 square inches removed. · GT1/GT2/GT3/GTL/GTX Direct Injection now permitted if OE, using only OE pump, hoses, injectors. · GT2/3 Nissan, Mazda, Mitsubishi 4G93, QR25DE/DD, QE25DE/DD Direct Injection now permitted per 9.1.2.F.7.5.E. · FF Honda Fit gains Fast Forward FF800-100 oversize piston ring pack option. · GTX adds KTM X-Bow classification with restrictor and weight specifications effective 2024-01-01. · GTL spec lines moved to contiguous position with GT2 and GT3; GTA category and spec lines renumbered and moved behind GTL. · GTX Ligier LMP3 3.7L NA classified at 2203 lbs with 22 mm restrictor. · GTX Ligier JSP4 newly classified as GTX Misc with restrictor and weight specified. · FA Pro Formula Mazda front wheels widen to 10 in. max; rear wheels narrow to 14 in. min. · FA Pro Formula Mazda maximum bodywork width behind front wheels increases to 51.97 inches. · FA MSR Formula Mazda FMzR added to Table 2 classification. · Fields Cardinal V8 classified in GT1 with Ford V8 engine, 4.9L displacement, 2100 lbs minimum weight. · FF Honda Fit engine adds Fast Forward part number alternatives for intake, exhaust, oil system, and scavenge pump components. · FA BDA engine displacement specification line added to Table 1, effective 2023-01-01. · Formula Renault 2.0 (10-17) reclassified from FX to FA; weight reduced to 1280 lbs, restrictor removed. · FA Swift 016 2.3L restrictor increases from 31mm to 32mm SIR; minimum weight drops 30 lbs to 1420. · GT2 TA2 and GTA throttle body part numbers updated to GM 90mm electronic #12570790 or Edelbrock 90mm mechanical #33869 or #3870. · Pro Formula Mazda allows street or bridge port, unrestricted apex seals, 70mm throttle body, 99cm wing height max, 132cm bodywork width max. · GT taillights may now be original style or a panel graphic with functioning red LED brake lamps; wording change only. · Porsche 992 GT3 Cup Car newly classified in GTX. · FA Ligier JS F3 must comply with Formula Regional Americas rules instead of FIA Formula 3 Regional Technical Regulations. · FA sealed engines must undergo full inspection; competitor pays reassembly and resealing costs. · FA Formula Lites FL15 and FR Americas Ligier JS F3 engine sealing requirements clarified to reference respective series technical regulations. · GTX Wolf GB08 F1 Ford 52XS V8 added to classification at 1725 lbs minimum weight. · C7 Corvette Grand Sport classified in GTX Misc at 3200 lbs with option to remove displacement on demand valve train. · GTX eligible prototypes expanded: IMSA GTP years changed to 1981-1993, five prototype categories added. · FA transmission rule clarified: transverse shafts prohibited except final drive and motorcycle gearbox in Formula 1000. · FA Swift 016 2.5 liter aero spec now references 2.3 liter notes instead of N notes. · FA Pro Formula Mazda now allows street port or bridge port, previously porting was prohibited. · GTX McLaren 720s GT3 newly classified at 3000 lbs with 3000 mm restrictor. · FA adds Honda K20Z3 2.0L engine spec at 1350 lbs minimum and Mazda MZR 2.0L spec at 1300 lbs minimum to Table 1. · GTX-FIA GT3 removes all intake restrictor requirements for fifteen car models; McLaren name corrected. · GT3 Fun Cup Beetle EVO3 classified with 1984 cc sealed SOHC engine, 2060 lbs minimum weight. · FA Mazda MZR 2.0 spec line removes redundant '2.0' designation; Honda Civic K20Z3 spec line unchanged. · GTX SRO-GT4 Porsche 718 Club Sport MR GT4 classified, unrestricted, 2900 lbs minimum weight. · FA Toyota 1800 moves from Table 1 to Table 2 (Spec Line Cars). · FA Swift 016 Mazda MZR/Ford Duratec wheel width specification clarified: front 10, rear 14 minimum and 15 maximum. · GTA part numbers updated: 0-80541-1 to 0-80541-2 in two sections and 6010 to 6014X in TA2 Appendix. · Grullon GT with 2.0L K20 moved from GTX to GT2-ST, minimum weight 2350 lbs, unrestricted. · FA rule wording clarified: Table 1 for purpose-built and ex-pro cars, Table 2 for spec line cars with exceptions noted. · FA Mazda MZR/Ford Duratec 2296cc and 2500cc moved from Table 1 to Table 2. · FA Mazda MZR 2.0 and Honda Civic K20Z3 remove sequential designation from 5-speed transmission spec. · GTX Grullon GT added, unrestricted, 2350 lbs, factory spec required. · FA Mazda MZR 2.0 limited to Ralt RT40, RT41, Swift 008, 014 chassis; Honda Civic K20Z3 removes Swift 016 chassis. · FA Swift 016 2.3 liter engine name corrected to Mazda MZR/Ford Duratec. · FA Swift 016 2.5 liter engine name corrected to Mazda MZR/Ford Duratec. · FA removes four spec lines and replaces Ford Duratec/Mazda MZR with Honda B16 at 1615cc, 1175 lbs minimum. · FA Spec Line C loses 25 lbs to 1175; Line I loses 75 lbs to 1175; Line K gains 15 lbs to 1175. · FA purpose built and ex-Pro Atlantic cars lose 25 lb sequential transmission penalty wording. · FA Ligier JS F3 car name corrected in FR Americas spec line. · FA Ford Duratec/Mazda MZR 2500 spec line D wording cleanup: 4-valve becomes 4 valves per cylinder. · FA Honda Civic K20Z3 intake manifold and throttle body assembly now allows AT Power Direct-To-Head 45mm individual throttle bodies as alternative to HPD parts. · FF block relief permitted only as needed to fit allowed crankshaft. · FA Ford Duratec/Mazda MZR intake restrictor reduced from 32mm to 30mm SIR; Swift 016 2.5 Mazda restrictor reduced from 35mm to 33mm SIR. · FA Toyota 4A-GE engines cleaned up, spec lines A and B engine designations corrected. · FA Ford BD Series max displacement increases from 1600 to 1615 cc, minimum weight stays 1200 lbs. · FA Ford Duratec/Mazda MZR and Honda B16 both now 1615cc max displacement; Honda B16 removes NA requirement. · FA Pro Formula Mazda engine specs moved from Table 1 to Table 2 notes; Renesis Rotary details consolidated. · FA F3 Americas spec line updated effective 2021-03-01; specific changes not legible in provided text. · Formula Lites Crawford FL15 newly classified in FA. · FF class cylinder head may now have optional coolant bleed line fitting to top of head for air release. · FF Honda LC1 ECU by HPD permitted effective 12/1/2020, must use HPD lambda sensor. · GT1, GT2, GT3, GTL, GTX now permit turbocharging/supercharging if listed on spec line. · FF Honda LC1 ECU implementation date changed from 3/1/2020 to pending availability of support materials. · GTX Chevrolet Camaro ZL1 LT4 with factory supercharger classified at 3400 lbs minimum weight. · GTX adds KTM X-Bow GT4, turbocharged 2.5L Audi TFSI I5, 2000 lbs minimum weight. · FA stock engines not given weight adjustment; modified engines now allowed in class. · TA2 Gurney flap wording clarified: terminology standardized to 'Gurney flap', height limits and thickness specifications remain 0.50 inch / 0.625 inch or 0.375 inch / 0.0625 inch depending on configuration. · STO rear wing wording clarified: 'wicker' changed to 'Gurney flap' in maximum chord and mounting height rules. · GT classes clarify Gurney flap wording, replacing wickerbill/tab terminology with flap; specifications unchanged. · FA engine modifications wording clarified: bore/crankshaft/stroke/flywheel unrestricted if displacement limit met, distributor/transistor ignition allowed without engine modification, compression ratio increasable by machining/gasket chang… · FA transmission rules clarified: no more than five forward speeds and operational reverse gear unless Table 2 notes otherwise. · FA Swift 016 Mazda Duratec Gurney flap wording clarified; terminology and mounting rules unchanged. · GTX tube frame cars must weigh 2780 pounds; stock car bodies now permitted. · FA Volkswagen 1835cc SOHC removed from Table 1. · FA engine rules clarified: blocks and heads must be OEM unless Tables note exceptions. · GTX adds Lotus Evora GTS with 3.5L 2GR-FE engine, no restrictor, 2950 lbs minimum weight. · FA Formula 1000 motorcycle-based engine compression ratio raised to 14.5:1 from 13.5:1. · FA removes Ex-FSV front wheel width 6–8 inches and rear 8–10 inches provisions; all cars use front 10 inches, rear 14–15 inches. · FA Formula 3 engines now allowed through 2017, previously 2008, with 30mm restrictor required. · FF alternator changes from not required to optional. · FA engine note clarification removes Table E reference, Pro Formula Mazda directed to Table 1. · FF allows Honda HPD LC1 low-cost ECU with lambda sensor; E1 ECU no longer supported but existing units permitted if sealed. · FF rain tyres now allow Hoosier W3 Radial in addition to existing Hoosier Wet option. · GT1, GT2, GT3, GTL, GTX may omit windshield clips if factory glass is bonded per original specifications. · Formula 1000 motorcycle-based engine classified into FA, throttle bodies and ECUs unrestricted. · F1000 reclassified into FA with specification changes effective 2020-01-01. · FA Swift 016 2.3L Mazda Duratec restrictor reduced from 33mm to 31mm SIR, making it slower. · Factory Five Type 65 Coupe R with Ford 302/351 or 5.0/5.2L NA added to GTX-MISC at 2600 lbs. · FA wheel dimension rules moved from Bodywork subsection to General section; no specification changes. · FA Mazda MZR 2.0 now limited to Ralt RT40, Ralt RT41, and Swift 014 chassis only. · FA Honda Civic K20Z3 engines consolidated: three separate base/uprated specs removed, replaced with single unified 1350 lb minimum weight spec for Swift 014/016. · FA Swift 014 Mazda MZR 2.0 piston minimum weight reduced from 320g to 280g. · FA Line N minimum weight increases to 1375 lbs. · FA cars must install AIM part #X47KPFSOLO2R0 data box mount for Majors and Runoffs. · GTX tube frame cars gain fuel injection with 90mm maximum throttle body size. · Ligier JS2 R classified in GTX, no performance parameters specified in filing. · GT1 and GT2/GT3/LITE ride height requirements removed from GCR sections 9.1.2.D.5.a.1 and 9.1.2.F.7.b. · FA Formula 3 car sequential gearbox weight penalty of 25 lbs removed; minimum weight now 1215 lbs. · GTX replaces all FIA GT4 references with SRO GT4. · FA Swift 014-Mazda MZR 2.0 engine now requires OE block casting #LF95 and specific OE components instead of sealed Elite Engines sourcing. · FA Swift 016 Mazda Duratec 2.3L and 2.5L minimum weight increases from 1420 to 1450 lbs. · FF Honda Fit permitted to use 0.25mm oversize pistons, cylinder honing increased to 73.315mm maximum. · FF heat shield rule clarified: thermal wrap allowed on manifold exterior if easily removable for inspection. · FF catch tank minimum capacity rules clarified: coolant catch tank now one U.S. pint minimum, oil catch tank one U.S. quart minimum. · GTX FIA GT3: Audi R8 40mm restrictor 2900 lbs, BMW Z4 70mm 2800 lbs, Ferrari 488 35mm restrictor 3025 lbs classified.showhide
FA Classify FR European Championship car as spec line car in Table 2 #37658cars addedneutralFA adds Tatuus F.3 T-318 or FR-19 as spec line car in Table 2 for Formula Regional European Championship.
GTX Correct language regarding OEM Areo Devices #37137wordingneutralTA2 rear wing height rule clarified: OEM aerodynamic devices exempt from peak-of-roof requirement.
FF Change FF/FC Weight with Sequential Gearbox #36651weightfasterFF and FC cars with sequential gearbox must add 10 lbs. to minimum weight, down from 25 lbs.
FF Alternative Oversize Honda Fit Pistons #37064wordingneutralFF Honda Fit allows Fast Forward 0.25mm oversize pistons PN FF800-110 as alternative; piston diameter spec clarified to 2.8835 inches.
FF Update to FF EGR Blanking Plate Rule #36633wordingneutralFF VTEC activation valve must function; EGR blanking plate rule clarified with Fast Forward part numbers.
GTX Request for Spec Line 1010 Reconsideration #35009weight +300 lbsslowerGT2-ST Acura NSX minimum weight raised to 3000 lbs, restrictor increased to 45mm TIR.
GTX Rear Blade Spoiler Clarification #35261aerofasterGT1, GT2, GT3, GTL, GTX rear spoiler maximum surface area limit of 295.0 square inches removed.
GTX GT Direct Injection allowance and rules #35437enginefasterGT1/GT2/GT3/GTL/GTX Direct Injection now permitted if OE, using only OE pump, hoses, injectors.
GTX GT2/3 remove Direction Injection not allowed in Spec line notes #35439inductionfasterGT2/3 Nissan, Mazda, Mitsubishi 4G93, QR25DE/DD, QE25DE/DD Direct Injection now permitted per 9.1.2.F.7.5.E.
FF Honda Fit Oversize Piston Rings #35305wordingneutralFF Honda Fit gains Fast Forward FF800-100 oversize piston ring pack option.
GTX KTM X Bow GTX #34956cars addedneutralGTX adds KTM X-Bow classification with restrictor and weight specifications effective 2024-01-01.
GTX Errors in GTCS Headings and Use of the Terms Category and ClassChange existing GTL and GTA Rules #34453wordingneutralGTL spec lines moved to contiguous position with GT2 and GT3; GTA category and spec lines renumbered and moved behind GTL.
GTX Request Ligier LMP3 Classification #34043cars addedneutralGTX Ligier LMP3 3.7L NA classified at 2203 lbs with 22 mm restrictor.
GTX Ligier JSP4 Request #34173cars addedneutralGTX Ligier JSP4 newly classified as GTX Misc with restrictor and weight specified.
FA Simplify Pro Formula Mazda wheel allowance #34190tyres & wheelsunclearFA Pro Formula Mazda front wheels widen to 10 in. max; rear wheels narrow to 14 in. min.
FA E&O - Correct Pro Formula Mazda spec line dimensional equivalent #34085aerofasterFA Pro Formula Mazda maximum bodywork width behind front wheels increases to 51.97 inches.
FA Add new spec line for MSR Formula Mazda FMzR to Table 2 #34139cars addedneutralFA MSR Formula Mazda FMzR added to Table 2 classification.
GTX Please classify Fields Cardinal V8 #33784cars addedneutralFields Cardinal V8 classified in GT1 with Ford V8 engine, 4.9L displacement, 2100 lbs minimum weight.
FF Add Fast Forward Part Numbers for Honda Fit Engine #33752wordingneutralFF Honda Fit engine adds Fast Forward part number alternatives for intake, exhaust, oil system, and scavenge pump components.
FA BDA Displacement #33431wordingneutralFA BDA engine displacement specification line added to Table 1, effective 2023-01-01.
FA Reclassify 2010-2017 Formula Renault 2.0 as a spec line car in FA #33395cars addedfasterFormula Renault 2.0 (10-17) reclassified from FX to FA; weight reduced to 1280 lbs, restrictor removed.
FA Change Swift 016 2.3L restrictor size and minimum weight #33472induction -30 lbsfasterFA Swift 016 2.3L restrictor increases from 31mm to 32mm SIR; minimum weight drops 30 lbs to 1420.
GTX GT2 (TA2)/GTA Part Number Update #33315wordingneutralGT2 TA2 and GTA throttle body part numbers updated to GM 90mm electronic #12570790 or Edelbrock 90mm mechanical #33869 or #3870.
FA Pro Formula Mazda Dimension E&O #33160wordingneutralPro Formula Mazda allows street or bridge port, unrestricted apex seals, 70mm throttle body, 99cm wing height max, 132cm bodywork width max.
GTX Tail lights on all GT category race cars. #32799wordingneutralGT taillights may now be original style or a panel graphic with functioning red LED brake lamps; wording change only.
GTX Classify 992 GT3 Cup #32649cars addedneutralPorsche 992 GT3 Cup Car newly classified in GTX.
FA Update FR Americas rulebook requirement #32491wordingneutralFA Ligier JS F3 must comply with Formula Regional Americas rules instead of FIA Formula 3 Regional Technical Regulations.
FA Clarify verification of sealed engine compliance #32522wordingneutralFA sealed engines must undergo full inspection; competitor pays reassembly and resealing costs.
FA Clarify Formula Lites and FR Americas sealed engine requirement #32523wordingneutralFA Formula Lites FL15 and FR Americas Ligier JS F3 engine sealing requirements clarified to reference respective series technical regulations.
GTX Add Classification to the accepted Model Table #31981cars addedneutralGTX Wolf GB08 F1 Ford 52XS V8 added to classification at 1725 lbs minimum weight.
GTX Request to classify C7 Corvette Grand Sport IN GTX Misc #32254cars addedneutralC7 Corvette Grand Sport classified in GTX Misc at 3200 lbs with option to remove displacement on demand valve train.
GTX E&O list of eligible prototypes #32511cars addedneutralGTX eligible prototypes expanded: IMSA GTP years changed to 1981-1993, five prototype categories added.
FA E&O FA Transmission section #32251wordingneutralFA transmission rule clarified: transverse shafts prohibited except final drive and motorcycle gearbox in Formula 1000.
FA E&O Swift 016 2.5 liter Aero column #32363wordingunclearFA Swift 016 2.5 liter aero spec now references 2.3 liter notes instead of N notes.
FA Closing the Gap #31934inductionfasterFA Pro Formula Mazda now allows street port or bridge port, previously porting was prohibited.
GTX McLaren 720s GT3 #31955cars addedneutralGTX McLaren 720s GT3 newly classified at 3000 lbs with 3000 mm restrictor.
FA Reorganize Tables 1 and 2 #31985cars addedneutralFA adds Honda K20Z3 2.0L engine spec at 1350 lbs minimum and Mazda MZR 2.0L spec at 1300 lbs minimum to Table 1.
GTX Remove restrictions from GTX-FIA GT3 #32039inductionfasterGTX-FIA GT3 removes all intake restrictor requirements for fifteen car models; McLaren name corrected.
GTX Request car classification #31032cars addedneutralGT3 Fun Cup Beetle EVO3 classified with 1984 cc sealed SOHC engine, 2060 lbs minimum weight.
FA E&O Table 2 engine names #31085wordingneutralFA Mazda MZR 2.0 spec line removes redundant '2.0' designation; Honda Civic K20Z3 spec line unchanged.
GTX Request to classify 2020 Porsche 718 GT4 Clubsport MR #30956cars addedneutralGTX SRO-GT4 Porsche 718 Club Sport MR GT4 classified, unrestricted, 2900 lbs minimum weight.
FA Move Toyota 1800 to Table 2 #30822cars addedneutralFA Toyota 1800 moves from Table 1 to Table 2 (Spec Line Cars).
FA E&O Swift 016 wheel width reference #30939wordingneutralFA Swift 016 Mazda MZR/Ford Duratec wheel width specification clarified: front 10, rear 14 minimum and 15 maximum.
GTX Request to Update GTA Obsolete Part Numbers #30615wordingneutralGTA part numbers updated: 0-80541-1 to 0-80541-2 in two sections and 6010 to 6014X in TA2 Appendix.
GTX GTX class correction to GT2/ST #30973cars addedneutralGrullon GT with 2.0L K20 moved from GTX to GT2-ST, minimum weight 2350 lbs, unrestricted.
FA Update FA rules package #30717wordingneutralFA rule wording clarified: Table 1 for purpose-built and ex-pro cars, Table 2 for spec line cars with exceptions noted.
FA Move Mazda MZR/Ford Duratec 2296cc and 2500cc to Table 2 #30718wordingneutralFA Mazda MZR/Ford Duratec 2296cc and 2500cc moved from Table 1 to Table 2.
FA Clean up Table 2 Mazda MZR 2.0L and Honda Civic K20Z3 spec lines #30719wordingneutralFA Mazda MZR 2.0 and Honda Civic K20Z3 remove sequential designation from 5-speed transmission spec.
FA E&O Mazda MZR 2.0 and Honda Civic K20Z3 chassis eligibility #30632wordingneutralFA Mazda MZR 2.0 limited to Ralt RT40, RT41, Swift 008, 014 chassis; Honda Civic K20Z3 removes Swift 016 chassis.
FA Correct engine name in Swift 016 2.3 liter spec line #30447wordingneutralFA Swift 016 2.3 liter engine name corrected to Mazda MZR/Ford Duratec.
FA Correct engine name in Swift 016 2.5 liter spec line #30448wordingneutralFA Swift 016 2.5 liter engine name corrected to Mazda MZR/Ford Duratec.
FA Revise Table 1 Spec Lines and clarify application of Engine Notes #30456cars addedunclearFA removes four spec lines and replaces Ford Duratec/Mazda MZR with Honda B16 at 1615cc, 1175 lbs minimum.
FA Update Table 1 Weights for Spec Lines C, I, and K #30355weight -25 lbsfasterFA Spec Line C loses 25 lbs to 1175; Line I loses 75 lbs to 1175; Line K gains 15 lbs to 1175.
FA Remove redundant reference in Table 2 spec line #30366wordingfasterFA purpose built and ex-Pro Atlantic cars lose 25 lb sequential transmission penalty wording.
FA Correct the name of the FR Americas car #30369wordingneutralFA Ligier JS F3 car name corrected in FR Americas spec line.
FA Clean up Spec Line D in Table 1 #30372wordingneutralFA Ford Duratec/Mazda MZR 2500 spec line D wording cleanup: 4-valve becomes 4 valves per cylinder.
FA Table 2 Honda K20Z3 request #30386inductionfasterFA Honda Civic K20Z3 intake manifold and throttle body assembly now allows AT Power Direct-To-Head 45mm individual throttle bodies as alternative to HPD parts.
FF Kent crankshaft clarification #30426wordingneutralFF block relief permitted only as needed to fit allowed crankshaft.
FA E&O FA Intake Restrictors #30273inductionslowerFA Ford Duratec/Mazda MZR intake restrictor reduced from 32mm to 30mm SIR; Swift 016 2.5 Mazda restrictor reduced from 35mm to 33mm SIR.
FA Clean up Spec Lines A and B in Table 1 #30274wordingneutralFA Toyota 4A-GE engines cleaned up, spec lines A and B engine designations corrected.
FA Clean up Spec Line C in Table 1 #30275enginefasterFA Ford BD Series max displacement increases from 1600 to 1615 cc, minimum weight stays 1200 lbs.
FA Clean up Spec Lines J and L in Table 1 #30276wordingneutralFA Ford Duratec/Mazda MZR and Honda B16 both now 1615cc max displacement; Honda B16 removes NA requirement.
FA Move engine specifications to Pro Formula Mazda spec line notes #30278wordingneutralFA Pro Formula Mazda engine specs moved from Table 1 to Table 2 notes; Renesis Rotary details consolidated.
FA Update F3 Americas spec line #30280wordingunclearFA F3 Americas spec line updated effective 2021-03-01; specific changes not legible in provided text.
FA Request to classify Formula Lites Crawford FL15 #29702cars addedneutralFormula Lites Crawford FL15 newly classified in FA.
FF Allow Optional Coolant Bleed Line to Correct a Known Problem #29673wordingneutralFF class cylinder head may now have optional coolant bleed line fitting to top of head for air release.
FF Clarification regarding Honda LC1 ECU implementation date #29684wordingneutralFF Honda LC1 ECU by HPD permitted effective 12/1/2020, must use HPD lambda sensor.
GTX GT Category Wording #29193wordingunclearGT1, GT2, GT3, GTL, GTX now permit turbocharging/supercharging if listed on spec line.
FF Clarification regarding Honda LC1 ECU implementation #29135wordingneutralFF Honda LC1 ECU implementation date changed from 3/1/2020 to pending availability of support materials.
GTX Request Car classification #28935cars addedneutralGTX Chevrolet Camaro ZL1 LT4 with factory supercharger classified at 3400 lbs minimum weight.
FA Request to Adjust FB Weight for Stock Engines #29005wordingneutralFA stock engines not given weight adjustment; modified engines now allowed in class.
GTX TA2 Gurney flap wicker clarification #28874wordingneutralTA2 Gurney flap wording clarified: terminology standardized to 'Gurney flap', height limits and thickness specifications remain 0.50 inch / 0.625 inch or 0.375 inch / 0.0625 inch depending on configuration.
GTX STO Gurney flap wicker clarification #28883wordingneutralSTO rear wing wording clarified: 'wicker' changed to 'Gurney flap' in maximum chord and mounting height rules.
FA E&O permitted engine modifications #28831wordingneutralFA engine modifications wording clarified: bore/crankshaft/stroke/flywheel unrestricted if displacement limit met, distributor/transistor ignition allowed without engine modification, compression ratio increasable by machining/gasket chang…
FA E&O Transmissions #28832wordingneutralFA transmission rules clarified: no more than five forward speeds and operational reverse gear unless Table 2 notes otherwise.
FA Swift 016 Gurney flap wicker clarification #28884wordingneutralFA Swift 016 Mazda Duratec Gurney flap wording clarified; terminology and mounting rules unchanged.
GTX Request to Re-classify SP Stock car to GTX #28333cars addedneutralGTX tube frame cars must weigh 2780 pounds; stock car bodies now permitted.
FA Remove redundant spec line in Table 1 #28720removedneutralFA Volkswagen 1835cc SOHC removed from Table 1.
FA E&O general engine rules #28772wordingneutralFA engine rules clarified: blocks and heads must be OEM unless Tables note exceptions.
GTX Request to Classify Lotus Evora GTS #27057cars addedneutralGTX adds Lotus Evora GTS with 3.5L 2GR-FE engine, no restrictor, 2950 lbs minimum weight.
FA Request higher compression ratio and prior weights for F1000 cars #28162enginefasterFA Formula 1000 motorcycle-based engine compression ratio raised to 14.5:1 from 13.5:1.
FA Remove redundant wheel dimension provisions #28554wordingneutralFA removes Ex-FSV front wheel width 6–8 inches and rear 8–10 inches provisions; all cars use front 10 inches, rear 14–15 inches.
FA E&O Formula 3 spec line #28596enginefasterFA Formula 3 engines now allowed through 2017, previously 2008, with 30mm restrictor required.
FF E&O FF Kent Engine alternator language #28204wordingneutralFF alternator changes from not required to optional.
FA FA weight correction/clarification #28430wordingneutralFA engine note clarification removes Table E reference, Pro Formula Mazda directed to Table 1.
FF Honda Racing HPD low cost ECU proposal #27563engineneutralFF allows Honda HPD LC1 low-cost ECU with lambda sensor; E1 ECU no longer supported but existing units permitted if sealed.
FF Update rain tire designation #28443tyres & wheelsneutralFF rain tyres now allow Hoosier W3 Radial in addition to existing Hoosier Wet option.
GTX Windshield Clips #27323wordingneutralGT1, GT2, GT3, GTL, GTX may omit windshield clips if factory glass is bonded per original specifications.
FA Request to merge FB into FA #25611cars addedfasterFormula 1000 motorcycle-based engine classified into FA, throttle bodies and ECUs unrestricted.
FA Suggestions for FB/F1000 into FA #27319cars addedunclearF1000 reclassified into FA with specification changes effective 2020-01-01.
FA Change Swift 016 - 2.3 liter Mazda Duratec restrictor size #27880inductionslowerFA Swift 016 2.3L Mazda Duratec restrictor reduced from 33mm to 31mm SIR, making it slower.
GTX Request Factory Five Daytona coupe classification #26308cars addedneutralFactory Five Type 65 Coupe R with Ford 302/351 or 5.0/5.2L NA added to GTX-MISC at 2600 lbs.
FA Move wheel dimensions from Bodywork subsection to #27493wordingneutralFA wheel dimension rules moved from Bodywork subsection to General section; no specification changes.
FA Table 2 Mazda MZR 2.0 E&O #27640wordingneutralFA Mazda MZR 2.0 now limited to Ralt RT40, Ralt RT41, and Swift 014 chassis only.
FA Follow up to Letter #27344 on Honda Powered FA Rules #27363wordingneutralFA Honda Civic K20Z3 engines consolidated: three separate base/uprated specs removed, replaced with single unified 1350 lb minimum weight spec for Swift 014/016.
FA Swift 014 Mazda MZR 2.0 E&O #27305enginefasterFA Swift 014 Mazda MZR 2.0 piston minimum weight reduced from 320g to 280g.
FA Adjust Line N restrictor size and minimum weight #26691weight +30 lbsslowerFA Line N minimum weight increases to 1375 lbs.
FA Add data plate requirement #26707wordingneutralFA cars must install AIM part #X47KPFSOLO2R0 data box mount for Majors and Runoffs.
GTX Request GTX Fuel injection for previous GT-1 tube frame cars #26141inductionfasterGTX tube frame cars gain fuel injection with 90mm maximum throttle body size.
GTX Request to Classify Ligier JS2 R #26535cars addedneutralLigier JS2 R classified in GTX, no performance parameters specified in filing.
GTX Request Ride Height Clarification #26600wordingneutralGT1 and GT2/GT3/LITE ride height requirements removed from GCR sections 9.1.2.D.5.a.1 and 9.1.2.F.7.b.
FA Request to add FA engine spec lines #26183weightfasterFA Formula 3 car sequential gearbox weight penalty of 25 lbs removed; minimum weight now 1215 lbs.
GTX Replace FIA references with SRO #26427wordingneutralGTX replaces all FIA GT4 references with SRO GT4.
FA FA MZR 2.0 Engine Specification #25814wordingneutralFA Swift 014-Mazda MZR 2.0 engine now requires OE block casting #LF95 and specific OE components instead of sealed Elite Engines sourcing.
FA FA 016 weight increase #26063weightslowerFA Swift 016 Mazda Duratec 2.3L and 2.5L minimum weight increases from 1420 to 1450 lbs.
FF Request for Oversize Honda Fit Pistons #25810enginefasterFF Honda Fit permitted to use 0.25mm oversize pistons, cylinder honing increased to 73.315mm maximum.
FF Heat Shield - Fit Intake #26102wordingneutralFF heat shield rule clarified: thermal wrap allowed on manifold exterior if easily removable for inspection.
FF Request catch cans/tanks clarification #26158wordingneutralFF catch tank minimum capacity rules clarified: coolant catch tank now one U.S. pint minimum, oil catch tank one U.S. quart minimum.
GTX GTX Homologation table update #26034cars addedneutralGTX FIA GT3: Audi R8 40mm restrictor 2900 lbs, BMW Z4 70mm 2800 lbs, Ferrari 488 35mm restrictor 3025 lbs classified.
Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of FF" is the class's best as a share of FF's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when FF's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.