STU vs STL vs SMX pace at Buttonwillow Raceway Park
Quickest here:STU 1:50.913 Tony Rivera, Cal Club 2026 qualifying · STL 1:54.845 Gavin Wardle, Cal Club 2026 race · SMX 1:56.431 Ethan Lampe, Cal Club 2025 qualifying
STUSTLSMXsolid race · dashed qualifying · slower is lower
STUSTLSMXsolid race · dashed qualifying · each class's best lap as a share of STU's at the same event (the reference class, changeable above); 100% is level, higher is quicker
Event
STU
STL
SMX
Qual best
Race best
Trap
Qual best
Race best
Trap
vs STU
% of STU
Qual best
Race best
Trap
vs STU
% of STU
Cal Club 2026 CALCL262026-02-21
1:50.913Tony Rivera · fastest of 6 · top 5 within 14.1s-4.488s (-3.89%)
1:52.737Tony Rivera · fastest of 7 · top 5 within 7.7s-0.903s (-0.79%)
135.2Tony Rivera+21.8 mph (+19.3%)
1:57.526Jared Korth · fastest of 10 · top 5 within 1.2s+2.563s (+2.23%)
1:54.845Gavin Wardle · fastest of 11 · top 5 within 4.7s-0.837s (-0.72%)
136.6Bryce Johnson+26.2 mph (+23.7%)
+2.108squal +6.613s
101.9%qual 106.0%
1:56.503Lincoln Larson · fastest of 15 · top 5 within 0.7s+0.072s (+0.06%)
1:57.973William Wallis · fastest of 15 · top 5 within 0.8s+0.556s (+0.47%)
141.6Joey Andrews+28.0 mph (+24.6%)
+5.236squal +5.590s
104.6%qual 105.0%
24 rule changes (STU: 17, STL: 3, SMX: 4)9 weight · 3 tyres & wheels · 2 cars added · 2 induction · 1 engine · 7 wording · STL minimum weights increase across all classes, 1300 cc gains 195 lbs to 1950, up to 1850 cc at 2500. · STU Mazda MZR (LF, L3, L5) Turbo classified; Jack Spania Racing 70 mm intake manifold and Fab9 Tuning bottom-mount turbo kit approved. · STU 36mm restrictor allows 2830 lbs (up 10 lbs from 2820); 37mm allows 2980 lbs (down 5 lbs from 2985). · STU cars over 3150 lbs lose 275-tire option with 2% weight adder. · STU Honda K20 and K24 engines lose 2% minimum weight penalty. · STU Honda K24 engine swap weight increases by 2% effective November 1, 2025. · STU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs. · STL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs. · STU-TCR tire width increases to 275 with weight adder raised from 100 to 150 pounds. · STL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs. · STU 2.8-3.2L N/A engines now allow 245 max tire width; over 3150 lbs may run 275 with 2% weight penalty. · STU Mazda MZR may use Goodwin 61-2510 or Gato Performance 31972 intake manifold. · STU Honda JDM H23a added, 2259cc displacement, minimum weight per Chart, must meet ST engine regulations. · SMX drivers must submit data acquisition files on time or face suspension and $250 fine. · SMX penalty language clarified: level 1 and 3 infractions may carry $1,000 fine; level 2 and 4 may carry $500 fine. · SMX Toyo RR P235/40/ZR17 tire rules clarified: one set per weekend, marking after first session, damage replacement procedures revised. · SMX data submission deadline extended from 30 to 60 minutes after each timed session. · STL Mazda MX5 Challenge minimum weight now references GCR 9.1.7.1 instead of 2500 lbs; spec components removed, only alternative tires allowed. · STU wheel width rules clarified: cars ≤2,850 lbs max 8 inches, cars >2,850 lbs max 9 inches. · STU Spec Line GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tire options clarified with weight adjustments. · STU BMW N54/N55 3.0L classified at Chart +3% minimum weight; N54 twin turbo not allowed. · STU Mini Cooper S SC supercharger pulley diameter reduced from 2.285 to 2.185. · STU Honda K20C1 Turbo I4 exempted from 3% DI weight adder in Spec Lines Table A. · STU GT3U minimum weight increases 150 to 250 pounds.showhide
STL Weight adjustment for STL #39579weightslowerSTL minimum weights increase across all classes, 1300 cc gains 195 lbs to 1950, up to 1850 cc at 2500.
STU Request for Permission on Aftermarket Turbo Kit and Intake #39529cars addedfasterSTU Mazda MZR (LF, L3, L5) Turbo classified; Jack Spania Racing 70 mm intake manifold and Fab9 Tuning bottom-mount turbo kit approved.
STU Turbo Inlet Restrictor Table #38961inductionslowerSTU 36mm restrictor allows 2830 lbs (up 10 lbs from 2820); 37mm allows 2980 lbs (down 5 lbs from 2985).
STU 275 Tire Rule #38983tyres & wheelsslowerSTU cars over 3150 lbs lose 275-tire option with 2% weight adder.
STU STU Honda Engine weight penalty #39375weightfasterSTU Honda K20 and K24 engines lose 2% minimum weight penalty.
STU Non-Homologated Engine Swaps - Specifically K24A2 w/ Honda CRZ #38746weightslowerSTU Honda K24 engine swap weight increases by 2% effective November 1, 2025.
STU Lotus Weight Reduction E&O #38919weightfasterSTU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs.
STL Lotus Weight Reduction #38772weight -50 lbsfasterSTL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs.
STU STU-TCR Adjustments #38723tyres & wheelsslowerSTU-TCR tire width increases to 275 with weight adder raised from 100 to 150 pounds.
STU Lotus Weight Reduction #38772weight -50 lbsfasterSTL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs.
STU 2.8-3.2L N/A Engine Allowances #38007tyres & wheelsunclearSTU 2.8-3.2L N/A engines now allow 245 max tire width; over 3150 lbs may run 275 with 2% weight penalty.
STU 2006-2015 Mazda Miata Intake Manifold #38422wordingneutralSTU Mazda MZR may use Goodwin 61-2510 or Gato Performance 31972 intake manifold.
STU Requesting Approval of the JDM Honda h23a #38489cars addedneutralSTU Honda JDM H23a added, 2259cc displacement, minimum weight per Chart, must meet ST engine regulations.
SMX SMX Data Submission - Penalties #38248wordingneutralSMX drivers must submit data acquisition files on time or face suspension and $250 fine.
SMX Committee) SMX Penaly Clarification updated language #38337wordingneutralSMX penalty language clarified: level 1 and 3 infractions may carry $1,000 fine; level 2 and 4 may carry $500 fine.
SMX Clarify Tire Marking Regs #38004wordingneutralSMX Toyo RR P235/40/ZR17 tire rules clarified: one set per weekend, marking after first session, damage replacement procedures revised.
SMX SMX Data Submission Timeframe #38039wordingneutralSMX data submission deadline extended from 30 to 60 minutes after each timed session.
STL E&O: SMX Allowance in STL #37945wordingunclearSTL Mazda MX5 Challenge minimum weight now references GCR 9.1.7.1 instead of 2500 lbs; spec components removed, only alternative tires allowed.
STU Wheel Size Inconsistency #38018wordingneutralSTU wheel width rules clarified: cars ≤2,850 lbs max 8 inches, cars >2,850 lbs max 9 inches.
STU Table C: STU-GT3U Clarification #38268weightfasterSTU Spec Line GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tire options clarified with weight adjustments.
STU BMW N54/N55 Engine Allowance Follow Up #37447engineneutralSTU BMW N54/N55 3.0L classified at Chart +3% minimum weight; N54 twin turbo not allowed.
STU STU Mini Cooper pulley size clarification re: letter #36980 #37717inductionfasterSTU Mini Cooper S SC supercharger pulley diameter reduced from 2.285 to 2.185.
STU Question About a Weight Modifier #37782weightfasterSTU Honda K20C1 Turbo I4 exempted from 3% DI weight adder in Spec Lines Table A.
STU Increase Minimum Weight #37919weight +100 lbsslowerSTU GT3U minimum weight increases 150 to 250 pounds.
Cal Club 2025 CALCL252025-02-22
1:55.401Wilson Powell · fastest of 4 · top 4 within 8.7s
1:53.640Rylan Hazelton · fastest of 5 · top 5 within 8.0s
113.3Rylan Hazelton
1:54.963Nick Leverone · fastest of 16 · top 5 within 3.3s
1:55.682Nick Leverone · fastest of 17 · top 5 within 2.6s
110.4Ryan Gutile
+2.042squal -0.438s
101.8%qual 99.6%
1:56.431Ethan Lampe · fastest of 15 · top 5 within 1.5s
1:57.417Ethan Lampe · fastest of 15 · top 5 within 1.6s
113.6Ryan Gutile
+3.777squal +1.030s
103.3%qual 100.9%
139 earlier rule changes on record, in force before Cal Club 2025 (from 2019)22 induction · 16 cars added · 13 engine · 13 weight · 7 aero · 5 tyres & wheels · 63 wording · STU Audi 1.8T wagon deleted; Porsche 944 1800 weight to Chart, turbo inlet restrictor removed. · STU-GT3 reclassified as STU-GT3U effective January 1, 2026. · STU GT3 TCR gains 275-width tire option with 100 lb weight penalty, but not in A compound. · SMX allows OE instrument cluster relocation for aftermarket dash mounting, with wiring re-routed only; alternate gauges now permitted. · STL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval. · STL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval. · STU BMW N54/N55 turbo inlet restrictors now required per GCR definition; turbo swapping prohibited. · STU Mini Cooper S SC 1900 restricts to 2.565 diameter pulley; 2100 allows 2.285 diameter pulley. · SMX Spec MX-5 camera requirement wording changed; non-functioning recorder now grounds for penalty or disqualification. · SMX Spec MX-5 must run latest AIM Data Logger Spec MX-5 ECU Protocol; wording clarification for technical compliance. · SMX Mazda Miata OE versus OEM definitions clarified in GCR Section 9.1.7.1. · SM and SMX shifter bushing rules clarified: alternate bushing at shift lever bottom now allowed. · STU RWD turbo cars no longer required to reduce restrictor by 1 mm from table. · STU Mini Cooper S SC: alternate LEAP OMICRON hood scoop LEP-OMICRON3 permitted. · STU BMW S54 B32 OEM now permits dry sump oiling system. · STL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems. · STL Acura/Honda B-series and Mazda MZR restrictors reduced 2mm; minimum weights down 25–75 lbs for 1900–2000cc engines. · STL Mazda 12A must keep 5th and 6th intake port actuators and valves, no longer allowed removal or disabling. · STL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems. · STL Mazda RX-7 12A (79-85) now allows auto-type 2 bbl with 42mm choke(s) on dual-y manifold as alternate to stock Nikki 4 bbl. · Toyota GR Cup and GR86 Cup (2022-) newly classified in STU at 2700 lbs with 2387 cc engine. · STL ITA/ITS RX7 and 1985+ ITA/ITS/ITB/ITC vehicles clarified to conform to section 9.1.4.2 tire specifications. · STU Mazda BP5A classified at 1839 cc maximum displacement, 2023-04-01. · STU minimum weight chart updated: 2450cc to 2595lbs, 2600cc to 2710lbs. · STL Spec MX5 clutch, wheels, and tyres specified: ACT 0000-02-5004-G6, 17x8 wheels, Toyo RR and RA1 235-40-17. · STU Mazda 13B Turbo classified, streetport only, stock turbos prohibited, alternatives allowed. · STU OEM louver vents now exempt from vent count and 200 square inch allowance. · STU 2400cc non-4-valve engines gain 9% base weight reduction; DI turbo prep limits removed. · STU normally-aspirated 2976–3200 cc single-throttle engines lose 10% base engine weight reduction. · ST redundant language removed from balance shaft and pulley modification rules. · STU cars that qualified for 9 inch wheels in 2021 may continue through 2022 only. · STU splitter definition clarified: must be single-plane with no vertical deviations, attached to lowest front point. · STU BMW S52B32 minimum weight drops 90 lbs to 3110; max displacement cut to 3152 cc. · STU BMW S50B32 Euro classified at 3201 cc displacement, 3300 lbs minimum weight. · ST engine swap origin country requirement changes from North America to the United States for case-by-case approval. · STU Honda CRX (84-91) and Civic Del Sol (93-97) ineligible for front wheel drive weight reductions. · STU vehicles at or over 2950 lbs base weight may use 9 inch wide wheels instead of 8.0 inch maximum. · STU minimum weights reduced: 2450cc to 2596 lbs, 2500cc to 2635 lbs, 2550cc to 2675 lbs. · STU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed. · STL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements. · STU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed. · STU Audi A4 1.8T minimum weight fixed at 3050 lbs, VF30 turbo with 35mm restrictor now required only. · STL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements. · STU engines may delete balance shafts and plug openings; alternate pulleys allowed for timing belt or chain operation only. · STU hood vents allowed to include louvers within 200 sq. inch area. · STL and STU piston engines clarified: intake manifold and cylinder head porting remains free. · STL Mazda Renesis flat plate restrictor increases from 55mm to 60mm. · STL Mazda RX-7 12A 79-85 clarifies carburetor, emissions, and water jacket modification rules. · STU adds Honda K23 with 2354cc displacement and minimum weight per chart, K24 block allowed with K23 internals and head. · STU Honda K23 internals rule relaxed to require only K23 crankshaft, allowing other internal modifications. · STL and STU piston engines clarified: intake manifold and cylinder head porting remains free. · STL Spec MX-5 removes redundant specification line; no performance change. · STU fender flare wording clarified: exterior contour of any wheel opening may not change opening size, location or shape from side view. · STU Mazda 12A Bridge Port Miata weight reduced from 2550 lbs to 2350 lbs. · STL Volkswagen 2.0L TFSI 1984cc classified with turbocharger removal required, meeting all other STL specs. · STL Pontiac Solstice/Saturn Sky allowed 4" ride height. · STL Mazda B5 DOHC added to classification with standard STL regulations. · STL Honda B16A JDM restrictor reduced from 54mm to 53mm. · STU fender flare rules clarified: maximum 2 inches, must cover tire contact patch from above, cannot alter body configuration or wheel opening geometry. · ST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions. · STU Honda S2000 allows F20/F22 K24 crankshaft with chart weight for achieved displacement. · ST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions. · STL GM Ecotec engines now permit any combination within the family, must use 55mm flat plate restrictor. · STL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs. · STL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs. · ST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment. · STL rear wing trailing edge, including end plates and gurney flap, maximum rearward mounting clarified to center of rearmost bodywork. · STL allows OEM gear sets from same manufacturer transmissions with input shaft modifications for fitment. · ST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment. · STU Porsche PDK automatic transmission limited to 8 forward speeds instead of torque converter restriction. · STU Mazda 13B Street Port 2400 removes choke location restriction, allows auto-type 2bbl with dual-Y manifold. · STU driveshaft and half-shaft materials change from OEM-type to steel or aluminum. · STL RWD strut suspension weight penalty cut to 0.5%, other RWD cut to 2.5%. · STL Honda F20C loses 2% weight penalty, minimum weight reduced by approximately 35 lbs. · STL Honda B16/B17/B18C1 restrictor tightened to 53mm; B18C variants and Mazda MZR to 52mm. · STU Mazda 13B Street Port classified at 2400 lbs minimum weight, replacing peripheral and bridge port variants. · ST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch. · ST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch. · STU fender flare rules reworded: up to 2" per corner allowed with 1% weight penalty total. · STL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments. · STL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change. · STL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments. · STL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change. · GT3 and STU add Borg-Warner EFR6258 to approved turbocharger list. · STU request for alternate intake manifold denied; no rule change issued. · GT3 and STU add Borg-Warner EFR6258 to approved turbocharger list. · STU large displacement turbo engines limited by GCR turbo list; non-turbo trim suggested as more competitive. · STU sequential shifters referred to Board of Directors for approval; no change implemented yet. · STL adds 2016-2019 Mazda MX-5 Global Cup at 2000cc, 2450-2550 lbs minimum weight. · STL Mazda MX-5 Club Model 06-15 allows Mazda header part number 0000-06-5407-NC. · STL Honda/Acura B18 non-C gets 54mm restrictor; B18C variants drop B18C1, get 53mm restrictor. · STU Mazda 13B Bridge Port and Street Port engines added with 2550 and 2250 lbs minimum weights respectively. · STL Honda B18 restrictor reduced from 54mm to 53mm flat plate; B18C1 added with 54mm restrictor. · STU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs. · STL Mazda MZR restrictor reduced from 54 mm to 53 mm. · STL Mazda MZR restrictor reduced from 55 mm to 53 mm. · STU Honda S2000 adds HKS Supercharger kits 12001-AH006 and 12001-AH010 as allowed. · STU Lotus Elise Cup R and SC models, plus Exige SC, gain 100–200 lbs minimum weight. · STU Volkswagen GTI/GLI MK5 and Jetta Mk4 may install turbo inlet restrictor in OEM turbo inlet housing. · STU Honda K20C1 Turbo I4 restrictor reduces from 36mm to 35mm. · STU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs. · STU Porsche 944 now permits VW/Audi 1.8L and 2.0L turbo engines as alternates. · STL Mazda Spec MX5 Challenge adds approved wheel part numbers 0000-04-5706-GM, 0000-04-5706-SL. · STU vehicles over 2951 lbs base weight may use 9 inch wide wheels, up from 2950 lbs. · STU turbocharged engines now use base weight instead of minimum weight, with 3% DI increase applied to base weight. · STU cars with manual OEM throttle bodies may convert to OEM electronic throttle body of same inner diameter. · Mazda Spec MX-5 Challenge classified in STL with 2000cc displacement and 2500 lbs minimum weight. · STU wing assembly wording corrected: no part higher than roof height. · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · STU Nissan SR20DET removes -2mm penalty in Table B. · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · STL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. · STU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement. · STU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · STU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock. · STU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body. · STU suspension rules clarified: alternate components from same manufacturer moved from section E to section D. · STU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold. · STU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules. · TCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019. · STU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight. · STL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. · STL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. · STL Mazda MX-5 Cup brake pad compound changed to open. · STL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. · STL Mazda 12 and 13B now permit port matching; previous ban removed. · Honda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork. · STU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances. · STU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed. · STU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10. · STU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options. · STU World Challenge car weight calculation method removed; new basis unclear from text provided. · STU AWD cars no longer required to reduce restrictor 1 mm from table. · STU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each. · STL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. · STL Mazda Miata removes maximum displacement limit and adjusts minimum weight. · STU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR.showhide
STU Audi 1.8t Wagon STU Table B #36685cars addedfasterSTU Audi 1.8T wagon deleted; Porsche 944 1800 weight to Chart, turbo inlet restrictor removed.
STU Merger GT3 to STU #37486wordingneutralSTU-GT3 reclassified as STU-GT3U effective January 1, 2026.
STU GT3 TCR Tire allowance #37494tyres & wheelsslowerSTU GT3 TCR gains 275-width tire option with 100 lb weight penalty, but not in A compound.
SMX E&O SMX Regs 9.1.7.1.D.5.u-.w #37070wordingneutralSMX allows OE instrument cluster relocation for aftermarket dash mounting, with wiring re-routed only; alternate gauges now permitted.
STL Request to Remove Miata Hubs from General category #37138wordingneutralSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
STU Request to Remove Miata Hubs from General category #37138wordingneutralSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
STU BMW N54/N55 Engine Allowance #37146inductionslowerSTU BMW N54/N55 turbo inlet restrictors now required per GCR definition; turbo swapping prohibited.
STU R53 15% Pulley Request #36980inductionslowerSTU Mini Cooper S SC 1900 restricts to 2.565 diameter pulley; 2100 allows 2.285 diameter pulley.
SMX SMX Camera Rule Correction #36496wordingneutralSMX Spec MX-5 camera requirement wording changed; non-functioning recorder now grounds for penalty or disqualification.
SMX Committee) AIM ECU Protocol #36556wordingneutralSMX Spec MX-5 must run latest AIM Data Logger Spec MX-5 ECU Protocol; wording clarification for technical compliance.
SMX Committee) OE versus OEM Definitons #36608wordingneutralSMX Mazda Miata OE versus OEM definitions clarified in GCR Section 9.1.7.1.
SMX Committee) Shifter Bushing #36611wordingneutralSM and SMX shifter bushing rules clarified: alternate bushing at shift lever bottom now allowed.
STU RWD Turbo Disadvantage #36255inductionfasterSTU RWD turbo cars no longer required to reduce restrictor by 1 mm from table.
STU Letter #35397 addendum #35453wordingneutralSTU Mini Cooper S SC: alternate LEAP OMICRON hood scoop LEP-OMICRON3 permitted.
STU S54 Drysump #35464wordingneutralSTU BMW S54 B32 OEM now permits dry sump oiling system.
STL ST Electric-Assisted Steering Systems #35066wordingneutralSTL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems.
STL BOP Adjustments #35112inductionfasterSTL Acura/Honda B-series and Mazda MZR restrictors reduced 2mm; minimum weights down 25–75 lbs for 1900–2000cc engines.
STL Mazda 12A #35320engineslowerSTL Mazda 12A must keep 5th and 6th intake port actuators and valves, no longer allowed removal or disabling.
STU ST Electric-Assisted Steering Systems #35066wordingneutralSTL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems.
STL Alternate Carburetor Request for 79-85 RX7 12a #35181inductionunclearSTL Mazda RX-7 12A (79-85) now allows auto-type 2 bbl with 42mm choke(s) on dual-y manifold as alternate to stock Nikki 4 bbl.
STU 2022 Toyota GR Cup for STU #34449cars addedneutralToyota GR Cup and GR86 Cup (2022-) newly classified in STU at 2700 lbs with 2387 cc engine.
STL Clarify STL table B - IT spec notes on Tires #34187wordingneutralSTL ITA/ITS RX7 and 1985+ ITA/ITS/ITB/ITC vehicles clarified to conform to section 9.1.4.2 tire specifications.
STU Alternate OEM Miata Intake Manifold #33827wordingneutralSTU Mazda BP5A classified at 1839 cc maximum displacement, 2023-04-01.
STU E&O STU NA Weight Chart. #33737weightfasterSTU minimum weight chart updated: 2450cc to 2595lbs, 2600cc to 2710lbs.
STL Spec MX5 in STL #33473wordingneutralSTL Spec MX5 clutch, wheels, and tyres specified: ACT 0000-02-5004-G6, 17x8 wheels, Toyo RR and RA1 235-40-17.
STU Request Mazda 13 B turbo #32668cars addedneutralSTU Mazda 13B Turbo classified, streetport only, stock turbos prohibited, alternatives allowed.
STU Hood Vents and Intercooler Scoops #32733aerofasterSTU OEM louver vents now exempt from vent count and 200 square inch allowance.
STU Non 4 valve weight reduction removed #32808enginefasterSTU 2400cc non-4-valve engines gain 9% base weight reduction; DI turbo prep limits removed.
STU Error in new minimum weight table when combined with other text #32711engineslowerSTU normally-aspirated 2976–3200 cc single-throttle engines lose 10% base engine weight reduction.
STU Redundant Language in May GCR #32713wordingneutralST redundant language removed from balance shaft and pulley modification rules.
STU Opposed to the Proposed STU Weight Chart #32381wordingneutralSTU cars that qualified for 9 inch wheels in 2021 may continue through 2022 only.
STU Clarification request for GCR 9.1.4.D.3.a Splitter Definition #32414wordingneutralSTU splitter definition clarified: must be single-plane with no vertical deviations, attached to lowest front point.
STU Request Adjustment to Min Weight for STU BMW E36 M3 (95-99) #31535weight -90 lbsfasterSTU BMW S52B32 minimum weight drops 90 lbs to 3110; max displacement cut to 3152 cc.
STU BMW E36 M3 Canadian (North American) S50B32 engine #31866cars addedneutralSTU BMW S50B32 Euro classified at 3201 cc displacement, 3300 lbs minimum weight.
STU Engine Swap Origin Country #32209wordingneutralST engine swap origin country requirement changes from North America to the United States for case-by-case approval.
STU CRX/Civic Del Sol #32214weightslowerSTU Honda CRX (84-91) and Civic Del Sol (93-97) ineligible for front wheel drive weight reductions.
STU Error correction #32383tyres & wheelsfasterSTU vehicles at or over 2950 lbs base weight may use 9 inch wide wheels instead of 8.0 inch maximum.
STU Single TB Weight Modifiers Add to Chart #32393weightfasterSTU minimum weights reduced: 2450cc to 2596 lbs, 2500cc to 2635 lbs, 2550cc to 2675 lbs.
STL Single TB Weight Modifiers #31449weightfasterSTU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed.
STL Improved Touring Tires #32063tyres & wheelsneutralSTL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements.
STU Single TB Weight Modifiers #31449weightfasterSTU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed.
STU Request to Remove A4 1.8t from STU Spec Line Tables #31465weightslowerSTU Audi A4 1.8T minimum weight fixed at 3050 lbs, VF30 turbo with 35mm restrictor now required only.
STU Improved Touring Tires #32063tyres & wheelsneutralSTL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements.
STU Request Allowance for Balance Shaft Delete in STU #31434enginefasterSTU engines may delete balance shafts and plug openings; alternate pulleys allowed for timing belt or chain operation only.
STU Request Louvers in hood vents #31916aeroneutralSTU hood vents allowed to include louvers within 200 sq. inch area.
STL Throttling Device Clarification #31323wordingneutralSTL and STU piston engines clarified: intake manifold and cylinder head porting remains free.
STL Mazda Renesis Restriction #31467inductionfasterSTL Mazda Renesis flat plate restrictor increases from 55mm to 60mm.
STL Clarification of 79-85 RX7 Spec line #31621wordingneutralSTL Mazda RX-7 12A 79-85 clarifies carburetor, emissions, and water jacket modification rules.
STU Request to Add Honda K23 Spec Line #30682cars addedneutralSTU adds Honda K23 with 2354cc displacement and minimum weight per chart, K24 block allowed with K23 internals and head.
STU RE: Aug FT letter 30682 #31060enginefasterSTU Honda K23 internals rule relaxed to require only K23 crankshaft, allowing other internal modifications.
STU Throttling Device Clarification #31323wordingneutralSTL and STU piston engines clarified: intake manifold and cylinder head porting remains free.
STL Request to clean up Spec MX-5 Redundancy #31069wordingneutralSTL Spec MX-5 removes redundant specification line; no performance change.
STU STU Fender flares #30696wordingneutralSTU fender flare wording clarified: exterior contour of any wheel opening may not change opening size, location or shape from side view.
STU Request weight reduction for 12A bridgeport motor in Miata #30751weight -200 lbsfasterSTU Mazda 12A Bridge Port Miata weight reduced from 2550 lbs to 2350 lbs.
STL VW Engine Request #30625engineslowerSTL Volkswagen 2.0L TFSI 1984cc classified with turbocharger removal required, meeting all other STL specs.
STL Request Mazda B5 DOHC #30420cars addedneutralSTL Mazda B5 DOHC added to classification with standard STL regulations.
STL Honda B16A (JDM) Restrictor change #30531inductionslowerSTL Honda B16A JDM restrictor reduced from 54mm to 53mm.
STU Request for Fender Flare Clarification #30375wordingneutralSTU fender flare rules clarified: maximum 2 inches, must cover tire contact patch from above, cannot alter body configuration or wheel opening geometry.
STL ST Oil Coolers E&O Correction to 9.1.4.2.H #30388wordingneutralST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions.
STU Provision for Interchangeable Engine Components Already Allowed #30342engineunclearSTU Honda S2000 allows F20/F22 K24 crankshaft with chart weight for achieved displacement.
STU ST Oil Coolers E&O Correction to 9.1.4.2.H #30388wordingneutralST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions.
STL GM Ecotec engines in STL #30247wordingneutralSTL GM Ecotec engines now permit any combination within the family, must use 55mm flat plate restrictor.
STL Super Touring Alternate Miata Hubs #30345wordingneutralSTL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs.
STU Super Touring Alternate Miata Hubs #30345wordingneutralSTL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs.
STL Brake Component Relocation #29990wordingneutralST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment.
STL Super Touring Wing Clarification #30111aeroneutralSTL rear wing trailing edge, including end plates and gurney flap, maximum rearward mounting clarified to center of rearmost bodywork.
STL Transmission Options #30118wordingneutralSTL allows OEM gear sets from same manufacturer transmissions with input shaft modifications for fitment.
STU Brake Component Relocation #29990wordingneutralST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment.
STU Porsche PDK #30081wordingneutralSTU Porsche PDK automatic transmission limited to 8 forward speeds instead of torque converter restriction.
STU Reference Letter #29333 Proposed STU 13B Spec Line Changes #30086inductionfasterSTU Mazda 13B Street Port 2400 removes choke location restriction, allows auto-type 2bbl with dual-Y manifold.
STU Drive Shaft Request #30087wordingneutralSTU driveshaft and half-shaft materials change from OEM-type to steel or aluminum.
STL Request for FWD and RWD Parity #29728weightfasterSTL RWD strut suspension weight penalty cut to 0.5%, other RWD cut to 2.5%.
STL Request to Remove Honda F20C 2% Weight Penalty #29815weightfasterSTL Honda F20C loses 2% weight penalty, minimum weight reduced by approximately 35 lbs.
STL Request for FWD and RWD Parity #30023inductionslowerSTL Honda B16/B17/B18C1 restrictor tightened to 53mm; B18C variants and Mazda MZR to 52mm.
STU 13B Rules Adjustment #29333cars addedslowerSTU Mazda 13B Street Port classified at 2400 lbs minimum weight, replacing peripheral and bridge port variants.
STL Request clarification on wing measurement #29640aeroneutralST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch.
STU Request clarification on wing measurement #29640aeroneutralST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch.
STU Request for Advanced Aero Rule Wording Clarification. #29124wordingneutralSTU fender flare rules reworded: up to 2" per corner allowed with 1% weight penalty total.
STL Minimum Weight Determination #27695wordingneutralSTL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments.
STL ST Gurney flap Wicker clarification #29012wordingneutralSTL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change.
STU Minimum Weight Determination #27695wordingneutralSTL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments.
STU ST Gurney flap Wicker clarification #29012wordingneutralSTL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change.
STL Request for Addition to GT3 Approved Turbo List #27576wordingneutralGT3 and STU add Borg-Warner EFR6258 to approved turbocharger list.
STU Request for Alternate Intake Manifold #26514wordingneutralSTU request for alternate intake manifold denied; no rule change issued.
STU Request for Addition to GT3 Approved Turbo List #27576wordingneutralGT3 and STU add Borg-Warner EFR6258 to approved turbocharger list.
STU Request BoP for my Car #29004wordingneutralSTU large displacement turbo engines limited by GCR turbo list; non-turbo trim suggested as more competitive.
STU Sequential Shifters in STU #29031wordingneutralSTU sequential shifters referred to Board of Directors for approval; no change implemented yet.
STL Request to add 2016-2019 GMX-5 Spec line #28604cars addedneutralSTL adds 2016-2019 Mazda MX-5 Global Cup at 2000cc, 2450-2550 lbs minimum weight.
STL Request to update PN for MX-5 #28622wordingunclearSTL Mazda MX-5 Club Model 06-15 allows Mazda header part number 0000-06-5407-NC.
STL Correction - Clarification Honda/Acura B18B engine Letter # 26209 #28873inductionunclearSTL Honda/Acura B18 non-C gets 54mm restrictor; B18C variants drop B18C1, get 53mm restrictor.
STU Rotary Help #27833cars addedneutralSTU Mazda 13B Bridge Port and Street Port engines added with 2550 and 2250 lbs minimum weights respectively.
STL STL Honda B18 restrictor changes #28794inductionfasterSTL Honda B18 restrictor reduced from 54mm to 53mm flat plate; B18C1 added with 54mm restrictor.
STL Change GM LNF 2.0 Allowance to LSJ Engine for Viable STL 2.0 #27884engineslowerSTU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs.
STL Acura/Honda B18C engine chart. Reduce the current 54 mm flat plat #28663inductionslowerSTL Mazda MZR restrictor reduced from 54 mm to 53 mm.
STL Mazda MZR engine chart. Reduce the current 55 mm flat plate to 53 #28664inductionslowerSTL Mazda MZR restrictor reduced from 55 mm to 53 mm.
STU Request to approve Honda S2000 HKS supercharger #27281enginefasterSTU Honda S2000 adds HKS Supercharger kits 12001-AH006 and 12001-AH010 as allowed.
STU Request BoP on the Lotus #27637weight +100 lbsslowerSTU Lotus Elise Cup R and SC models, plus Exige SC, gain 100–200 lbs minimum weight.
STU Turbo Inlet Restrictor On MK5 Volkswagen #27704inductionslowerSTU Volkswagen GTI/GLI MK5 and Jetta Mk4 may install turbo inlet restrictor in OEM turbo inlet housing.
STU Honda K20C1 removal #27732inductionslowerSTU Honda K20C1 Turbo I4 restrictor reduces from 36mm to 35mm.
STU Change GM LNF 2.0 Allowance to LSJ Engine for Viable STL 2.0 #27884engineslowerSTU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs.
STU Alternate Engine for Porsche 944 #28259engineunclearSTU Porsche 944 now permits VW/Audi 1.8L and 2.0L turbo engines as alternates.
STL Request to add wheel part numbers #28342wordingneutralSTL Mazda Spec MX5 Challenge adds approved wheel part numbers 0000-04-5706-GM, 0000-04-5706-SL.
STU Please Modify the STU Wheel Size Rule for Clarity #27694weightfasterSTU vehicles over 2951 lbs base weight may use 9 inch wide wheels, up from 2950 lbs.
STU Turbo Engine Cars Base Weight #28032wordingneutralSTU turbocharged engines now use base weight instead of minimum weight, with 3% DI increase applied to base weight.
STU Request for an electronic throttle body #27342wordingneutralSTU cars with manual OEM throttle bodies may convert to OEM electronic throttle body of same inner diameter.
STL Request to Classify Spec MX-5 Challenge in STL #27399cars addedneutralMazda Spec MX-5 Challenge classified in STL with 2000cc displacement and 2500 lbs minimum weight.
STU Request to correct E&O advanced aerodynamics #27290wordingneutralSTU wing assembly wording corrected: no part higher than roof height.
STL Request clarification for manifold and throttle in STU #27004inductionfasterSTU alternate intake manifolds now allowed case-by-case instead of prohibited.
STU Remove -2mm penalty from SR20DET Nissan #26982enginefasterSTU Nissan SR20DET removes -2mm penalty in Table B.
STU Request clarification for manifold and throttle in STU #27004inductionfasterSTU alternate intake manifolds now allowed case-by-case instead of prohibited.
STL Request Restrictor Plate correction #26779inductionfasterSTL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate.
STU Request to clarify afterrmarket side skirts exhaust exit #26814wordingneutralSTU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement.
STU Wheel Flare wording #26872wordingneutralSTU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty.
STL Request Ride Height Clarification #26597wordingneutralSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld.
STU Request Ride Height Clarification #26597wordingneutralSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld.
STU Request to Use Japanese Mazda 13b Intake Manifold #25790inductionfasterSTU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock.
STU Request Alternate Intake for Mazda MZR In a Rear Wheel Drive App. #26352inductionunclearSTU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body.
STU E&O Suspension #26424wordingneutralSTU suspension rules clarified: alternate components from same manufacturer moved from section E to section D.
STU Revisit B20 VTEC #26530enginefasterSTU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold.
STU Move Flared Fenders to STU Advanced Aero #26564aeroneutralSTU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules.
STU TCA Civic SI E&O #26606tyres & wheelsslowerTCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019.
STU S54 Spec line #26620wordingneutralSTU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight.
STL Request to reduce weight of RX8 with Renesis rotary #25781weight -100 lbsfasterSTL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs.
STL Request for Open Brake Pads On Mazda MX-5 Cup NC #25821wordingneutralSTL Mazda MX-5 Cup brake pad compound changed to open.
STL Request to clarify B18C1 GSR Honda B motor table #26209cars addedneutralSTL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch.
STL Port Matching #26415wordingfasterSTL Mazda 12 and 13B now permit port matching; previous ban removed.
STU Request to Class Assignment for 2017 Civic #24287cars addedneutralHonda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork.
STU Request to run E46 3246cc in STU #25126cars addedneutralSTU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances.
STU Engine Classification for Rotary #25564wordingunclearSTU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed.
STU K24/K20 Head Swap Clarification/Amendment #25899wordingneutralSTU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10.
STU Request to Classify 12a Bridge Ported Rotary Engine #25985cars addedneutralSTU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options.
STU World Challenge Car Eligibility #26387wordingunclearSTU World Challenge car weight calculation method removed; new basis unclear from text provided.
STU Request a phone call for discussion regarding weight #26398inductionfasterSTU AWD cars no longer required to reduce restrictor 1 mm from table.
STU Advanced Aero E&O #26413aeroneutralSTU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each.
STL Request to equalize FPR Reduction on all B-Series Vtec Engines #24746inductionslowerSTL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor.
STL Request E&O for Mazda Miata Spec Line #25955wordingunclearSTL Mazda Miata removes maximum displacement limit and adjusts minimum weight.
STU Request to Equalize Direct Injected Turbo Cars #24890cars addedneutralSTU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR.
Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of STU" is the class's best as a share of STU's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when STU's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.