Quickest here:EP 1:53.088 Glen McCready, Cal Club 2025 qualifying · STU 1:50.913 Tony Rivera, Cal Club 2026 qualifying · T1 1:46.465 Ian Barberi, Cal Club 2025 qualifying
EPSTUT1solid race · dashed qualifying · slower is lower
EPSTUT1solid race · dashed qualifying · each class's best lap as a share of EP's at the same event (the reference class, changeable above); 100% is level, higher is quicker
Event
EP
STU
T1
Qual best
Race best
Trap
Qual best
Race best
Trap
vs EP
% of EP
Qual best
Race best
Trap
vs EP
% of EP
Cal Club 2026 CALCL262026-02-21
1:57.474Kurt Frietzsche · fastest of 4 · top 4 within 4.5s+4.386s (+3.88%)
1:57.999Kurt Frietzsche · fastest of 4 · top 4 within 4.9s+4.512s (+3.98%)
131.6Joe Carr+23.8 mph (+22.1%)
1:50.913Tony Rivera · fastest of 6 · top 5 within 14.1s-4.488s (-3.89%)
1:52.737Tony Rivera · fastest of 7 · top 5 within 7.7s-0.903s (-0.79%)
135.2Tony Rivera+21.8 mph (+19.3%)
-5.262squal -6.561s
95.5%qual 94.4%
1:59.760Ed Gless · only car+13.295s (+12.49%)
1:59.123Ed Gless · only car+11.689s (+10.88%)
120.7Ed Gless-18.6 mph (-13.3%)
+1.124squal +2.286s
101.0%qual 101.9%
53 rule changes (EP: 23, STU: 17, T1: 13)19 weight · 7 induction · 6 cars added · 4 tyres & wheels · 3 engine · 1 removed · 13 wording · T1 Corvette C6 LS1/LS6 Spec Line reinstated: 3200 lbs minimum weight, 70mm restrictor required. · EP BMW 325i/is E30 throttle body specified as 60mm in fuel injection notes. · STU Mazda MZR (LF, L3, L5) Turbo classified; Jack Spania Racing 70 mm intake manifold and Fab9 Tuning bottom-mount turbo kit approved. · T1 Spec Line restrictor changes from 70mm flat plate to unspecified new specification. · EP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification. · EP BMW Z3 2.5L restrictor reduced 52mm to 50mm, weight increased to 2550 lbs base; five other BMW models get smaller restrictors. · STU 36mm restrictor allows 2830 lbs (up 10 lbs from 2820); 37mm allows 2980 lbs (down 5 lbs from 2985). · STU cars over 3150 lbs lose 275-tire option with 2% weight adder. · STU Honda K20 and K24 engines lose 2% minimum weight penalty. · Unable to summarize: letter states intent but provides no actual rule changes to S2000 specification. · T1 non-GT4 cars: multiple restrictors enlarged (70mm to 73mm, 75mm to 78mm, 55mm to 60mm, 61mm to 70mm); one weight increased to 3600. · T1 BMW M3 E92 (08-13) Spec Line 1090 removed entirely. · EP Nissan 280Z minimum weight reduced from 2560 to 2400 lbs. · EP Mazda MX-5 1.8L 90-97 weight reduced to 2125 lbs from 2150 lbs. · HP Austin-Healey Sprite/Midget 1098cc minimum weight drops 80 lbs to 1550. · HP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425". · HP Mini Cooper 07-15 valve lift reduced to .390", from .450". · FP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants. · EP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted. · EP Ford Mustang (94-98) fuel injected throttle body inside diameter specified at 60. · STU Honda K24 engine swap weight increases by 2% effective November 1, 2025. · HP Plymouth Arrow transmission max speeds clarified to 4 or 5. · EP, FP, HP wheel diameter added to Appendix G as absolute maximum specification. · EP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only. · STU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs. · STU-TCR tire width increases to 275 with weight adder raised from 100 to 150 pounds. · STL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs. · EP BMW Z4 03-05 restricted to 52mm flat plate intake restrictor. · EP Fiat 124 Spider 1600 & 2000 weight drops 50 lbs to 2000; carburetors gain 2mm chokes to 36mm. · STU 2.8-3.2L N/A engines now allow 245 max tire width; over 3150 lbs may run 275 with 2% weight penalty. · STU Mazda MZR may use Goodwin 61-2510 or Gato Performance 31972 intake manifold. · STU Honda JDM H23a added, 2259cc displacement, minimum weight per Chart, must meet ST engine regulations. · HP Fiat X-1/9 base weights reduced 50–53 lbs across 1300 and 1500 spec lines. · STU wheel width rules clarified: cars ≤2,850 lbs max 8 inches, cars >2,850 lbs max 9 inches. · STU Spec Line GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tire options clarified with weight adjustments. · Porsche 981 GT4 Clubsport added to T1 as spec line 4085, minimum weight 3100 lbs with driver. · T1 Honda S2000 minimum weight reduced from 2950 lbs to 2900 lbs. · T1 BMW E46 M3 permits BMW #GS7D36SG aftermarket sequential transmission in SL# 1060 and 1070. · T1 BMW M3 E92 minimum weight reduced to 3300 lbs. · T1 Mustang Darkhorse R gets 315 front and rear tyres, loses 500 lbs minimum weight to 3600. · Chevrolet Spark 16-22 classified HP Pre at 1850 lbs minimum weight, fuel injected, 1399 cc. · HP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1. · Cadillac CT4-V Blackwing added to T1 Spec Line 1115, 3564cc, 3750 lbs minimum weight. · EP BMW Z3 and 3-series models get smaller intake restrictors: Z3 2.5L to 52mm, Z3 2.8L to 55mm, 328i to 58mm, 325i to 56mm. · EP, FP, HP: interior or exterior mirrors meeting rule 9.3.36 now permitted. · EP Honda S2000 1997cc base loses 75 lbs to 2375; 2157cc base loses 60 lbs to 2450. · EP Mazda MX-5/Miata 99-05 minimum weight drops to 2100 lbs, 2153 lbs with power adder, 2205 lbs with two adders. · STU BMW N54/N55 3.0L classified at Chart +3% minimum weight; N54 twin turbo not allowed. · STU Mini Cooper S SC supercharger pulley diameter reduced from 2.285 to 2.185. · STU Honda K20C1 Turbo I4 exempted from 3% DI weight adder in Spec Lines Table A. · STU GT3U minimum weight increases 150 to 250 pounds. · T1 Mustang Spec 1430 restrictor opens 60mm to 65mm; Spec 1460 weight rises to 3500 lbs, restrictor 70mm; Corvette 1190 restrictor opens 67mm to 70mm; BMW 1090 restrictor narrows 40mm to 35mm; BMW 1100 weight rises to 3350 lbs.showhide
T1 LS1 into Corvette C6 Spec Line Request #39716cars addedcars addedT1 Corvette C6 LS1/LS6 Spec Line reinstated: 3200 lbs minimum weight, 70mm restrictor required.
EP Request to Update E30 BMW Throttle Body Diameter Verbiage #39363wordingwordingEP BMW 325i/is E30 throttle body specified as 60mm in fuel injection notes.
STU Request for Permission on Aftermarket Turbo Kit and Intake #39529cars addedfasterSTU Mazda MZR (LF, L3, L5) Turbo classified; Jack Spania Racing 70 mm intake manifold and Fab9 Tuning bottom-mount turbo kit approved.
T1 additional T1 adjustment #39520inductionunclearT1 Spec Line restrictor changes from 70mm flat plate to unspecified new specification.
EP TR2 Notes E&O #39180wordingunclearEP Triumph TR2-TR4A allows 5-speed gearbox without overdrive; removes Weber carb and weight specification.
EP Balance of Power #39187induction +50 lbsslowerEP BMW Z3 2.5L restrictor reduced 52mm to 50mm, weight increased to 2550 lbs base; five other BMW models get smaller restrictors.
STU Turbo Inlet Restrictor Table #38961inductionslowerSTU 36mm restrictor allows 2830 lbs (up 10 lbs from 2820); 37mm allows 2980 lbs (down 5 lbs from 2985).
STU 275 Tire Rule #38983tyres & wheelsslowerSTU cars over 3150 lbs lose 275-tire option with 2% weight adder.
STU STU Honda Engine weight penalty #39375weightfasterSTU Honda K20 and K24 engines lose 2% minimum weight penalty.
T1 Keep S2000 Classification #39344wordingunclearUnable to summarize: letter states intent but provides no actual rule changes to S2000 specification.
T1 Correcting and updating T1 GT4 spec lines #39394weight
T1 BOP adjustments to non GT4 T1 cars #39406induction +100 lbsfasterT1 non-GT4 cars: multiple restrictors enlarged (70mm to 73mm, 75mm to 78mm, 55mm to 60mm, 61mm to 70mm); one weight increased to 3600.
T1 Remove T1 Spec Line #39407removedremovedT1 BMW M3 E92 (08-13) Spec Line 1090 removed entirely.
EP Please Lower Weight of 280Z #38871weight -160 lbsfasterEP Nissan 280Z minimum weight reduced from 2560 to 2400 lbs.
EP Miata Weight Adjustment Follow Up #38949weight -25 lbsfasterEP Mazda MX-5 1.8L 90-97 weight reduced to 2125 lbs from 2150 lbs.
EP Weight Break for 1098 Midget / Sprite #38970weight -80 lbsfasterHP Austin-Healey Sprite/Midget 1098cc minimum weight drops 80 lbs to 1550.
EP HP Volvo 142 spec omission #38994engineslowerHP Volvo 142/142E gains compression ratio limit 12.0:1 and valve lift limit .425".
EP HP Mini DOHC 1.6 #38996engineslowerHP Mini Cooper 07-15 valve lift reduced to .390", from .450".
EP Add to Rabbit description #39019wordingwordingFP and HP Volkswagen Rabbit descriptions updated: Convertible changed to Cabriolet in FP; Cabriolet added to three HP engine variants.
EP Clean-up 9.1.5.E.7e #39025wordingwordingEP, FP, HP: rear drum brake to disc conversion clarified; rotors solid, diameter limited to largest front rotor permitted.
EP Add TB size to Ford Mustang (94-98) Spec Line #39130wordingwordingEP Ford Mustang (94-98) fuel injected throttle body inside diameter specified at 60.
STU Non-Homologated Engine Swaps - Specifically K24A2 w/ Honda CRZ #38746weightslowerSTU Honda K24 engine swap weight increases by 2% effective November 1, 2025.
EP HP Plymouth Arrow spec omission #38995wordingwordingHP Plymouth Arrow transmission max speeds clarified to 4 or 5.
EP Add Wheel Diameter to Appendix G #39008wordingwordingEP, FP, HP wheel diameter added to Appendix G as absolute maximum specification.
EP Add TB ID tolerance to general Prod rules #39009wordingwordingEP, FP, HP throttle body inside dimensions must remain stock with +/-.25mm tolerance; butterfly dimensions stock in FP, HP only.
STU Lotus Weight Reduction E&O #38919weightfasterSTU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs.
STU STU-TCR Adjustments #38723tyres & wheelsslowerSTU-TCR tire width increases to 275 with weight adder raised from 100 to 150 pounds.
STU Lotus Weight Reduction #38772weight -50 lbsfasterSTL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs.
EP BMW Z4 update #38490inductionslowerEP BMW Z4 03-05 restricted to 52mm flat plate intake restrictor.
EP EP Fiat 124 Spider Competition Adjustment Request #38498weight -50 lbsfasterEP Fiat 124 Spider 1600 & 2000 weight drops 50 lbs to 2000; carburetors gain 2mm chokes to 36mm.
STU 2.8-3.2L N/A Engine Allowances #38007tyres & wheelsunclearSTU 2.8-3.2L N/A engines now allow 245 max tire width; over 3150 lbs may run 275 with 2% weight penalty.
STU 2006-2015 Mazda Miata Intake Manifold #38422wordingwordingSTU Mazda MZR may use Goodwin 61-2510 or Gato Performance 31972 intake manifold.
STU Requesting Approval of the JDM Honda h23a #38489cars addedcars addedSTU Honda JDM H23a added, 2259cc displacement, minimum weight per Chart, must meet ST engine regulations.
EP Base Weight Adjustment for H-Production X1/9 Spec Lines #38255weight -50 lbsfasterHP Fiat X-1/9 base weights reduced 50–53 lbs across 1300 and 1500 spec lines.
STU Wheel Size Inconsistency #38018wordingwordingSTU wheel width rules clarified: cars ≤2,850 lbs max 8 inches, cars >2,850 lbs max 9 inches.
STU Table C: STU-GT3U Clarification #38268weightfasterSTU Spec Line GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tire options clarified with weight adjustments.
T1 Acceptance of Porsche 981 GT4 Clubsport into T1 #36664cars addedcars addedPorsche 981 GT4 Clubsport added to T1 as spec line 4085, minimum weight 3100 lbs with driver.
T1 Request to Restore T1 Honda S2000 to Proper Weights #37644weight -50 lbsfasterT1 Honda S2000 minimum weight reduced from 2950 lbs to 2900 lbs.
T1 DCT Transmission in E46 #37964wordingwordingT1 BMW E46 M3 permits BMW #GS7D36SG aftermarket sequential transmission in SL# 1060 and 1070.
T1 Reduce E92 M3 Minimum Weight to 3050 #38092weightfasterT1 BMW M3 E92 minimum weight reduced to 3300 lbs.
T1 Finalize Spec Line for T1 Darkhorse #38106tyres & wheelsfasterT1 Mustang Darkhorse R gets 315 front and rear tyres, loses 500 lbs minimum weight to 3600.
EP Request for Classification of Chevrolet Spark #37755cars addedcars addedChevrolet Spark 16-22 classified HP Pre at 1850 lbs minimum weight, fuel injected, 1399 cc.
EP Request to Lower Ford Festiva Minimum Weight to 1600 LBS #37939weight -100 lbsfasterHP Ford Festiva 88-93 minimum weight drops to 1600 lbs, variants to 1640 and 1680 lbs; compression ratio raised to 11.0:1.
T1 Cadillac CT4-V Blackwing #38003cars addedcars addedCadillac CT4-V Blackwing added to T1 Spec Line 1115, 3564cc, 3750 lbs minimum weight.
EP Request Competition Adjustment to BMW Z3 2.5L #37120inductionslowerEP BMW Z3 and 3-series models get smaller intake restrictors: Z3 2.5L to 52mm, Z3 2.8L to 55mm, 328i to 58mm, 325i to 56mm.
EP Interpretation of Production Rules on Mirrors #37235wordingwordingEP, FP, HP: interior or exterior mirrors meeting rule 9.3.36 now permitted.
EP Weight Reduction for Honda S2000 #37466weightfasterEP Honda S2000 1997cc base loses 75 lbs to 2375; 2157cc base loses 60 lbs to 2450.
EP Mazda 1999 Miata 1.8L #37488weight -50 lbsfasterEP Mazda MX-5/Miata 99-05 minimum weight drops to 2100 lbs, 2153 lbs with power adder, 2205 lbs with two adders.
STU BMW N54/N55 Engine Allowance Follow Up #37447engineengineSTU BMW N54/N55 3.0L classified at Chart +3% minimum weight; N54 twin turbo not allowed.
STU STU Mini Cooper pulley size clarification re: letter #36980 #37717inductionfasterSTU Mini Cooper S SC supercharger pulley diameter reduced from 2.285 to 2.185.
STU Question About a Weight Modifier #37782weightfasterSTU Honda K20C1 Turbo I4 exempted from 3% DI weight adder in Spec Lines Table A.
STU Increase Minimum Weight #37919weight +100 lbsslowerSTU GT3U minimum weight increases 150 to 250 pounds.
T1 Correct and make new T1 BOP adjustments. #37737weight +75 lbsunclearT1 Mustang Spec 1430 restrictor opens 60mm to 65mm; Spec 1460 weight rises to 3500 lbs, restrictor 70mm; Corvette 1190 restrictor opens 67mm to 70mm; BMW 1090 restrictor narrows 40mm to 35mm; BMW 1100 weight rises to 3350 lbs.
Cal Club 2025 CALCL252025-02-22
1:53.088Glen McCready · fastest of 5 · top 5 within 10.6s
1:53.487Glen McCready · fastest of 5 · top 5 within 10.6s
107.8Joe Carr
1:55.401Wilson Powell · fastest of 4 · top 4 within 8.7s
1:53.640Rylan Hazelton · fastest of 5 · top 5 within 8.0s
113.3Rylan Hazelton
+0.153squal +2.313s
100.1%qual 102.0%
1:46.465Ian Barberi · fastest of 2
1:47.434Ian Barberi · fastest of 3 · top 3 within 11.8s
139.3Drew Delmonico
-6.053squal -6.623s
94.7%qual 94.1%
281 earlier rule changes on record, in force before Cal Club 2025 (from 2019)50 cars added · 45 weight · 32 induction · 20 engine · 12 tyres & wheels · 10 aero · 6 suspension & brakes · 1 removed · 103 wording · 2 other · EP BMW Z3 2.5L requires 52mm flat plate intake restrictor; Z3 2.8L 55mm; 328i/is E36 58mm; 328i/ci E46 58mm; 325i/is E46 56mm; 325i/is E36 56mm; 325is M-Technic 56mm. · T1 Mustang gains 125 lbs to 3600, restrictor shrinks 65mm to 60mm. Corvette gains 50 lbs to 3500, restrictor shrinks 70mm to 67mm. BMW deleted. · T1 E46 M3 Spec Line 1050 allows VAC Motorsports throttle body VAC-TB-S54 on 3.250L engine instead of Dinan. · T1 Chevrolet Corvette C8 (2023-23) minimum weight reduced from 3600 lbs to 3500 lbs. · T1 Chevrolet Camaro Gen 5 restrictor increases from 75mm to 80mm flat plate. · T1 Audi R8 GT4 Spec Line #4020 maximum tyre size changes to 315 DOT, 305/645, or 30/65-18 (f), 33/68-18 (r) Non-DOT. · EP BMW 325i/is E30 (84-91) weight reduced 50–52 lbs across three spec lines to 2150, 2204, 2258. · STU Audi 1.8T wagon deleted; Porsche 944 1800 weight to Chart, turbo inlet restrictor removed. · STU-GT3 reclassified as STU-GT3U effective January 1, 2026. · STU GT3 TCR gains 275-width tire option with 100 lb weight penalty, but not in A compound. · EP Triumph GT6 switches to three Weber 40 DCOE carbs with 28mm chokes, weight rises 50 lbs to 1990. · STL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval. · STU BMW N54/N55 turbo inlet restrictors now required per GCR definition; turbo swapping prohibited. · T1 GT4 tire sizes adjusted across ten cars: most non-DOT rear to 305/660, Audi and McLaren 305/645, Camaro and Mustang 305/680. · BMW M4 GT4 (G82) added to T1 GT4 at 3525 lbs minimum weight with Red power stick control. · T1 Spec Lines now permits 5.5 inch clutch in Engine Notes. · T1 GT4 Spec Line 4020 restrictor opens from 44mm to 45mm, minimum weight drops to 3400 lbs. · Mustang Darkhorse R added to T1 homologated cars at 3,250 lbs minimum with 305/315 tires, ineligible for Runoffs until 3 Super Tour events. · T1 Corvette may roll or flatten wheel opening lips for tire clearance; plastic fenders may remove lips if edge thickness matches basic material. · T1 E46 M3 S54 can now use Dinan Throttle Body #D760-3400 on 3.250L engine. · HP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1. · EP Mazda Miata front and rear track widths increased to 1516/1534 mm (59.7/60.4 in.) across all generations. · STU Mini Cooper S SC 1900 restricts to 2.565 diameter pulley; 2100 allows 2.285 diameter pulley. · HP Volkswagen Golf and Jetta 85-92 track correction: front 1537mm (60.5in), rear 1529mm (60.2in). · STU RWD turbo cars no longer required to reduce restrictor by 1 mm from table. · Nissan 300ZX 84-89 classified to EP at 2550 lbs minimum, 2960cc 6-cyl SOHC, fuel injection, 12.0:1 compression limit, 0.500" valve lift limit. · Mazda RX-7 92-97 newly classified EP Prep Level 2 at 2200–2310 lbs with 13B 6-port rotary engine. · EP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains. · Mercedes AMG-C63 S (2023) classified in T1 with 4000 lbs minimum weight and 3700 restrictor. · T1 Honda S2000 classified with 2400 lb minimum weight, 2950 cc displacement, 4.75" supercharger pulley. · HP removes four redundant VW spec lines: Rabbit Cabriolet 1780, Scirocco 1588, Scirocco 1780 8-valve, Scirocco 1588. · STU Mini Cooper S SC: alternate LEAP OMICRON hood scoop LEP-OMICRON3 permitted. · STU BMW S54 B32 OEM now permits dry sump oiling system. · Pontiac GTO 2006-2009 LS1 added to T1 as Spec Line 1590, 5700 cc, 3400 lbs minimum. · HP Honda Civic 1.5 (88-91) weight reduced to 2175 lbs base, 2229 lbs with power adder, 2284 lbs with two. · STL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems. · C8 Corvette T1 restrictor plate increases from 70mm to 72mm flat plate. · T1 NEW class removes 23 spec lines including Acura NSX, Ferrari, Porsche 996, Nissan Z cars, and others; Porsche 997 spec line 1680 expiration removed. · EP BMW Z3 2.5L weight increases to 2500 lbs, 2563 lbs with turbo, 2625 lbs with supercharger. · EP Mazda MX-5 1.8L 1990-97 minimum weight drops to 2150 lbs; 1994-97 variants to 2000, 2050, 2100 lbs respectively. · EP Triumph GT6 dual 1.75" carbs weight drops to 1940 lbs; triple Weber 40 DCOE options consolidated. · EP Honda S2000 fuel injected throttle body inside diameter increases from 62mm to 64mm. · EP Triumph TR8 dry sump allowance moved from carburetor line to notes section. · EP Porsche 944/924S 2.5L and 2.7L weight minimums corrected: 2479cc to 2306/2363 lbs, 2681cc to 2358/2415 lbs. · T1-GT4 batch adjustments: five cars lighter, two heavier, restrictors and ECU maps changed, five models now eligible for Runoffs. · T1 spec lines 1000, 1010, 1020, 1040, 1360, 1400–1410, 1520–1680, 1700–1720 deleted entirely. · EP Porsche 944/924S combines 2.5L and 2.7L variants with new weights: 2250–2415 lbs depending on engine and year. · EP Triumph GT6 minimum weight reduced to 1800 lbs. · T1 Chevrolet Corvette C5 LS2 added with 6000cc displacement, 3300 lbs minimum weight, 72mm flat plate restrictor. · T1 Chevrolet Corvette C7 (14-19) including Z51, Grandsport newly classified as homologated car. · T1 Gen 5 Camaro minimum weight drops 75 lbs to 3475; restrictor increases 70mm to 75mm. · T1 Aston Martin Vantage permitted to use OEM Sportshift II transmission. · Pontiac GTO 2006-2009 re-integrated into T1 with LS2 at 3400 lbs, 72mm restrictor, and LS3 at 3500 lbs, 61mm restrictor. · T1 Porsche 997-1 GT3 Cup added at spec line 4210, minimum weight 3050 lbs. · EP Triumph TR8 78-81 removes alternate front hub allowance note; stock hubs now required. · EP Triumph GT6 carburetors change from SU or Stromberg to 1.5" Auto-type. · EP Triumph GT6 brakes may now use TR-6 standard or alternate calipers and discs. · Chevrolet Camaro GT4-R classified in T1 GT4 Spec Line 4035, minimum weight 3375 lbs, 315 max tire, 63mm restrictor, ineligible for Runoffs. · T1 Dodge Viper ACR / SRT RT-10 and ACR/ACR-X spec lines 1350 and 1370 remove 12/23 expiration. · T1 GT4 McLaren 570S, Mercedes AMG GT4, and Porsche 718 Cayman GT4 CS MR now eligible for Runoffs competition. · T1 GT4 BMW M4 Spec Line Number changed from 4050 to 4030. · T1 Corvette C5 gains approved aero parts: carbon rear spoiler, vented front splitter, side skirts, with 50 lb weight reduction allowed. · FP and HP Sprite, Midget, and Spitfire 1500 intake valve size corrected to 36.6/(1.44). · Toyota GR Cup and GR86 Cup (2022-) newly classified in STU at 2700 lbs with 2387 cc engine. · T1 Dodge Viper ACR/ACR-X restrictor increases from 50mm to 60mm flat plate. · T1 Dodge Viper ACR/ACR-X: Spec Line 1370 restrictor increases to 55mm, Line 1390 decreases to 55mm. · T1 Ford Mustang S197 05-14 now requires OEM 8.8 differential housing. · T1 Chevrolet Camaro Gen 5 LS7 gets two spec lines: 1131 with 70mm restrictor, 1136 with 53mm restrictor, both 3450 lbs minimum. · T1 Chevrolet Camaro Gen 5, Corvette C5 and C6: engine resleeve restricted to stock parameters only, no longer LS3 bore/stroke. · EP Porsche 914-6 2.0L intake valves increase to 2.0 mm, exhaust valves corrected to 38.0 mm. · T1 Ford Mustang S197 (05-14) reinstated with 3550 lbs minimum weight, 75mm restrictor, Voodoo engine permitted. · T1 GT4 weights clarified for nine cars, ranging from 3200 lbs Porsche 718 Cayman to 3575 lbs Aston Martin. · T1-GT4 McLaren 570S and Mercedes AMG GT4 front tires widen to 315 mm. · EP BMW Z3 2.5L intake restrictor reduced from 58mm to 56mm flat plate. · STU Mazda BP5A classified at 1839 cc maximum displacement, 2023-04-01. · T1 Chevrolet Camaro Gen5 LS3-6160 adds 70mm flat plate restrictor, weight 3550 lbs. · STU minimum weight chart updated: 2450cc to 2595lbs, 2600cc to 2710lbs. · T1 cars with aftermarket sequential transmissions get 10-inch max bellhousing; non-sequential cars gain 100 lbs weight break. · T1 GT4 all nine cars lose 125 lbs minimum weight with driver, from 3200–3575 to 3075–3450. · T1 removes GCR Section 9.1.9.1.A. and T1 Spec Lines entirely, sunsetting pre-2023 Touring 1 rules. · GT4 McLaren 570S maximum tire size changes to 285 front, 315 rear. · EP 79-85 RX-7 12A/13B brake spec simplification removes hub/rotor weight minimum allowance. · EP 280Z carburetor option adds Hitachi-SU 1bbl 46mm throttle bores alongside fuel injection. · EP Mazda RX-2, RX-3, RX-4, and 12A RX-7 now allow 2 bbl fuel injected throttle body w/ 42mm chokes on dual-y manifold. · EP Mazda RX-2, RX-3, RX-3SP, and RX-4 minimum weights reduced 50–52 lbs across all spec lines. · EP Triumph TR8 78-81 now allowed to run dry sump. · EP, FP, HP cylinder head ports limited to 1 inch maximum depth matching from mating surface. · EP Prep 280ZX (79-83) added to spec lines with 2425–2546 lbs, 2760cc SOHC 6-cyl, fuel injection, 12.0:1 compression limit, .500" valve lift limit. · Eight GT4 models added to T1 with weights from 3200 to 3575 lbs and restricted power per SRO 2022 rules. · VW New Beetle 2.5L 5-cyl added to EP at 2400–2520 lbs, 2480 cc, fuel injection, comp ratio 12.0:1 max, valve lift 0.500" max. · EP Mazda RX-7 12A/13B gains fuel injection option on dual-y manifold with 42mm choke(s). · EP VW Corrado 92-95 stroke corrected to 90.3 mm, displacement to 2792 cc. · STU Mazda 13B Turbo classified, streetport only, stock turbos prohibited, alternatives allowed. · STU OEM louver vents now exempt from vent count and 200 square inch allowance. · STU 2400cc non-4-valve engines gain 9% base weight reduction; DI turbo prep limits removed. · T1 Cadillac CTS/CTS-V, Chevrolet Camaro, Pontiac Firebird, Pontiac GTO 6162 OEM minimum weight reduced to 3475 lbs. · STU normally-aspirated 2976–3200 cc single-throttle engines lose 10% base engine weight reduction. · ST redundant language removed from balance shaft and pulley modification rules. · EP Subaru BRZ and Toyota 86/Scion FR-S model year ranges updated to 13-20. · T1-LP Ford Mustang FP350S restrictor increases from 70mm to 75mm. · Mercedes Benz AMG GT4 2017-2021 classified T1 Maximum at 3400 lbs minimum weight with HP-controlled SRO Power Level 2 engine. · EP Mazda MX-5 Global Cup 16-22 minimum weight set to 2400 lbs; sequential gearbox allowed with +150 lbs penalty. · BMW 128i (08-13) classified in EP at 2700 lbs minimum with stock throttle body, 11.0:1 compression ratio, 0.400 in. valve lift limits. · EP/FP/HP open cars may now use carbon fiber hardtops if they retain OEM appearance in all exterior profiles. · STU cars that qualified for 9 inch wheels in 2021 may continue through 2022 only. · STU splitter definition clarified: must be single-plane with no vertical deviations, attached to lowest front point. · EP Mazda RX-8 13B carburetor rules clarified: dual 2bbl carb, fuel injected throttle body, or stock fuel injection permitted. · EP and FP Production clarifies idle control valve rules: stock devices allowed original, removed with blocked ports, or mechanical replaced with electronic stock type. · STU BMW S52B32 minimum weight drops 90 lbs to 3110; max displacement cut to 3152 cc. · STU BMW S50B32 Euro classified at 3201 cc displacement, 3300 lbs minimum weight. · ST engine swap origin country requirement changes from North America to the United States for case-by-case approval. · STU Honda CRX (84-91) and Civic Del Sol (93-97) ineligible for front wheel drive weight reductions. · STU vehicles at or over 2950 lbs base weight may use 9 inch wide wheels instead of 8.0 inch maximum. · STU minimum weights reduced: 2450cc to 2596 lbs, 2500cc to 2635 lbs, 2550cc to 2675 lbs. · T1 Dodge Viper ACR displacement rises to 8400 OEM, minimum weight drops to 3550 lbs. · T1 Limited T1 wording changed to clarify all T1 cars permitted specifications. · T1 Mazda RX-7 classified: 2700 lbs minimum weight, 44mm restrictor, 13B Rotary with single Garrett Turbo #3076. · EP BMW Z3 2.5L intake restrictor reduced from 59mm to 58mm flat plate. · Ford Mustang 99-03 classified to EP at 2700/2768/2835 lbs; 94-98 Mustang weight reduced to 2550/2614/2678 lbs. · EP, FP, HP Improved Touring cars may use any DOT-approved tire per section 9.3.45 in Production class. · STU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed. · STU Audi A4 1.8T minimum weight fixed at 3050 lbs, VF30 turbo with 35mm restrictor now required only. · STL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements. · T1 Cadillac CTS/CTS-V, Chevrolet Camaro, Pontiac Firebird, Pontiac GTO LS3 minimum weight reduced to 3475 lbs. · T1 Camaro maximum displacement 7011 loses 50 lbs, to 3500. · T1 removes 33mm brake rotor thickness limit; rotors now unrestricted on thickness. · EP, FP, HP classes allow stock/original idle control devices unmodified or completely removed with openings blocked. · EP Porsche 968 (92-95) now allows dry sump. · EP 1979-1985 Mazda RX-7 12A and 13B weight reduced by 50-53 lbs across all configurations. · STU engines may delete balance shafts and plug openings; alternate pulleys allowed for timing belt or chain operation only. · STU hood vents allowed to include louvers within 200 sq. inch area. · EP Porsche 968 intake valve size increased from 37 to 39.0 mm. · EP, FP, HP front-wheel-drive cars may alter body and suspension to install alternate transmission, transaxle, and axle shaft. · EP BMW Z3 2.5L allows alternate throttle body from 92-95 325i with Turner adapter; head casting 1738400 permitted with specific blocks. · STU adds Honda K23 with 2354cc displacement and minimum weight per chart, K24 block allowed with K23 internals and head. · STU Honda K23 internals rule relaxed to require only K23 crankshaft, allowing other internal modifications. · STL and STU piston engines clarified: intake manifold and cylinder head porting remains free. · EP Porsche 944S2 89-91 requires 56mm flat plate intake restrictor; comp ratio max 12.0:1, valve lift max 0.500". · HP Corolla GTS RWD (84-87) added at 2300 lbs; HP Corolla FX16 FWD (87-88) added at 2260 lbs; old Corolla (84-87) removed. · T1 Mazda MX-5 Miata MazdaSpeed minimum weight rises to 2550 lbs, restrictor increases to 42mm. · T1 Chevrolet Corvette Cadillac XLR classified for model years through 2019. · HP Toyota MR-2 1.6L (85-89) track corrected to 15.47 inches front and rear. · Honda S2000 (00-03) reclassified as EP Prep with F22c engine option: 1997cc or 2157cc, weight 2450–2636 lbs depending on displacement. · EP Nissan 240-SX S13/S14 loses 200-210 lbs minimum weight; comp ratio rises to 12.0:1, valve lift to .500. · T1 BMW E46/E36/Z3 minimum weight increases to 2700 lbs, 3.4L engine car to 2750 lbs. · EP Lotus/Caterham 7 America carburetor changed from IT fuel injection prep to fuel injection. · Daimler SP 250 classified in EP at 2165 lbs with 2548 cc OHV 8-cylinder engine. · STU fender flare wording clarified: exterior contour of any wheel opening may not change opening size, location or shape from side view. · STU Mazda 12A Bridge Port Miata weight reduced from 2550 lbs to 2350 lbs. · T1 Dodge Viper SRT-10 restrictor increases from 45mm to 57mm. · T1 Chevrolet Corvette Cadillac XLR LS6 engine now permits Casting #799 heads with no other head modifications. · EP, FP, HP clarifies percentage weight penalties sum first, then apply to base weight, rounding to nearest pound. · T1 Ford Mustang Shelby/GT350/GT500 5.0L Coyote restrictor opens from 65mm to 70mm flat plate. · T1 Dodge Viper SRT-10 restrictor increases from 45mm to 57mm. · T1-LP Chevrolet Corvette C7 restrictor increases from 70 to 73 mm. · T1-LP Corvette Z06 06-13 now allows aluminum chassis replacement with equivalent OE steel chassis. · 84-87 Mazda 626 reclassified from FP to HP with 2300–2415 lbs weight, 1998cc SOHC, dual 32mm carbs. · FP Fiat X1/9 brake rotors change to 257 (10.1) x 12 (.407) solid disc. · EP Mazda MX-5 year range corrected from 06-14 to 06-15. · STU fender flare rules clarified: maximum 2 inches, must cover tire contact patch from above, cannot alter body configuration or wheel opening geometry. · T1 Chevrolet Camaro with 6162 displacement minimum weight reduced to 3500 lbs. · T1-LP Chevrolet Corvettes C5 Z06, C6 Grand Sport, and Z06 dry sump kit notes clarified to remove contradictions. · Mazda 3 S 04-08 classified in EP at 2350 lbs minimum, 2.26L DOHC, 12.0:1 compression, .500" valve lift limit. · STU Honda S2000 allows F20/F22 K24 crankshaft with chart weight for achieved displacement. · ST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions. · STL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs. · T1 LP removes 50 lbs weight allowance for stock headers, adds aero device allowance up to 100 lbs, permits headers. · ST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment. · STU Porsche PDK automatic transmission limited to 8 forward speeds instead of torque converter restriction. · STU Mazda 13B Street Port 2400 removes choke location restriction, allows auto-type 2bbl with dual-Y manifold. · STU driveshaft and half-shaft materials change from OEM-type to steel or aluminum. · T1 Ford Mustang Challenge 3-valve maximum displacement changes to 4600/5000. · T1 BMW E46 now allows carbon or fiberglass OEM-style dashboards with 25 pound penalty. · T1 Ford Mustang/Thunderbird limited to Shelby/Shelby GT350/GT500 models through 2018. · Dodge Viper ACR classified in T1 with 8400cc displacement, 3600 lbs minimum weight, 55mm restrictor. · BMW M2CS Club Sport classified in T1-LP Spec Lines effective 2021-02-01. · Porsche 997.1 GT3 Cup (2006-2011) classified in T1 at 3600cc, 3150 lbs minimum weight. · EP Austin-Healey 3000 Mk. I, II, III now allows TR-6 front calipers and discs as alternate. · STU Mazda 13B Street Port classified at 2400 lbs minimum weight, replacing peripheral and bridge port variants. · T1 Chevrolet Corvette Z06 years extended from 06-12 to 06-13. · FP Volkswagen Golf and Jetta 1.8 lose 50 lbs each, to 1900. HP Jetta GLI engine code removed. · EP, FP, HP Level 1 and Level 2 induction systems: clarified carburetor and fuel injection rules, jets/needles/rods unrestricted in Level 2. · EP Datsun SRL 311U Roadster minimum weight reduced to 1925 lbs from 2000 lbs. · EP Triumph TR8 78-81 weight reduced from 2600 to 2500 lbs. · ST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch. · T1 Corvette C8 Z51 gets wider wheels and tyres, weight drops 100 lbs to 3550. · HP 84-87 Toyota Corolla wheel diameter increases from 13 to 15 inches. · STU fender flare rules reworded: up to 2" per corner allowed with 1% weight penalty total. · EP BMW Z3 2.5L iron block casting 1738566-C designation removed, wording clarification only. · STL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments. · STL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change. · T1 rear wing Gurney flap wording clarified: Gurney flap in chord length and mounting height rules. · Porsche 911 S 67-68 classified in EP at three weight levels: 1800, 1845, or 1890 lbs. · STU request for alternate intake manifold denied; no rule change issued. · GT3 and STU add Borg-Warner EFR6258 to approved turbocharger list. · STU large displacement turbo engines limited by GCR turbo list; non-turbo trim suggested as more competitive. · STU sequential shifters referred to Board of Directors for approval; no change implemented yet. · EP BMW 2.8L, 328i E36/E46, and 325i E36 blocks now iron only; 325i E46 aluminum only. · STU Mazda 13B Bridge Port and Street Port engines added with 2550 and 2250 lbs minimum weights respectively. · T1 and T2 Corvettes may convert leaf spring suspension to coilover with 800 lb max spring rate allowed. · 1990-1994 Mazda Protege classified in FP Pre at 2150–2258 lbs with 1839cc DOHC engine, fuel injection. · HP Mini Cooper model year ranges for convertibles revised: 02-06 now includes 05-08, 07-13 now includes 09-15. · T1 Porsche 996 GT3 Cup eligible model years changed from 2002-2005 to 1998-2004. · T1 Corvette and Cadillac XLR permitted to install SCRSPLR-001 rear spoiler with OE bodywork. · T1 Gen 5 Camaro allowed 366mm OEM rear rotor and caliper without weight penalty. · EP Caterham 7 Spec Line removes redundant suspension note, clarifies engine prep limits and comp ratio to 10.0:1. · STU Honda S2000 adds HKS Supercharger kits 12001-AH006 and 12001-AH010 as allowed. · STU Lotus Elise Cup R and SC models, plus Exige SC, gain 100–200 lbs minimum weight. · STU Volkswagen GTI/GLI MK5 and Jetta Mk4 may install turbo inlet restrictor in OEM turbo inlet housing. · STU Honda K20C1 Turbo I4 restrictor reduces from 36mm to 35mm. · STU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs. · STU Porsche 944 now permits VW/Audi 1.8L and 2.0L turbo engines as alternates. · T1 Porsche 996 Spec Lines now allows 996 Cup Replica Rear deck lid. · T1 Acura NSX Turbo World Challenge and Audi TTRS GTS 2011 now require DOT tires per GCR section 9.3. · EP BMW Z3 2.5L compression ratio capped 12.0:1, valve lift .500, 59mm restrictor required; Z3 2.8L same limits added; 944S2 compression 12.0:1, valve lift .500, 56mm restrictor required. · EP BMW 325is M-Technic loses 100–105 lbs across three weight configurations, to 2550–2678. · HP Datsun 510 gains 40 DCOE carburetor option alongside existing 40 DCN and 36mm DCNVH choices. · EP BMW fuel injected throttle body maximum inside diameter set to 64mm. · STU vehicles over 2951 lbs base weight may use 9 inch wide wheels, up from 2950 lbs. · STU turbocharged engines now use base weight instead of minimum weight, with 3% DI increase applied to base weight. · T1 BMW E46 wagon with S54 engine allowed; displacement corrected from 3200 to 3250cc. · HP Datsun 1200 carburetor choke size increases from 26mm to 30mm. · T1 adds Subaru WRX/WRX STI 2005-2020 at 3000 lbs minimum weight with 46 mm restrictor. · T1 Ford Mustang GT (15-17) and GT5.0L (2018-) weight raised to 3500 lbs; Brembo BBK 380mm now at no penalty; restrictors removed from notes. · T1 Ford Mustang/Thunderbird 5000 Coyote OEM reclassified to include 2015–2017 and 2018+ model years with 65mm restrictor for 18+. · T1 BMW M3 E92 carbon dash allowed with 25 lb penalty. · T1 Corvette C5 Z06, C6 coupe, C6 Grand Sport, and Z06 may convert leaf springs to conventional coilover suspension. · FP and EP Mazda Miata models standardized to 55mm throttle body diameter; brake spec clarified. · EP, FP, HP cylinder head rules reorganized for clarity; no performance change. · STU cars with manual OEM throttle bodies may convert to OEM electronic throttle body of same inner diameter. · FP and HP Austin-Healey Sprite Mk I and MG Midget variants may replace rear bodywork aft of cockpit with stock-appearing alternate material components. · EP Mazda MX-5 Global Cup classification year changes from 16-18 to 16-19. · Production suspension rule clarifies spindles, hubs, bushings, bearings, ball joints unrestricted. · Production carb rules clarified: carburetor options, fuel injection throttle body dimensions, and intake manifold restrictions reorganised and refined. · EP, FP, HP carburetors clarified: jets, needles, metering rods, needle valves unrestricted; choke parts removable; permitted optional carburetors listed. · STU wing assembly wording corrected: no part higher than roof height. · T1-LP Chevrolet Camaro 1LE 2016- weight drops to 3500 lbs, restrictor increases to 70mm flat plate. · EP Mazda MX-5/Miata eligibility years expanded from 1999-2002 to 1999-2005. · Ford Mustang Challenge returns to T1 as E&O, 4600 cc, 3300 lbs minimum, no restrictor. · T1 Chevrolet Corvette Cadillac XLR year range corrected from 04-09. · STU Nissan SR20DET removes -2mm penalty in Table B. · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · T1 Camaro, CTS, Firebird, GTO restrictor increases from 67mm to 70mm flat plate. · STU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement. · STU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty. · T2-T4 clarifies DOT tire requirements; must have minimum U speed rating and be DOT certified; touring spec line supersedes other rules. · EP Mazda RX-8 firewall modification allowed for 13B engine fitment in stock location. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · Ford Mustang EcoBoost 3.5L classified in T1 at 3300 lbs minimum weight with 31mm restrictor. · T1 Corvette C5 body allowed C7 carbon aero parts, plus 50 lbs. · T1 Audi TTRS must conform to July 24th, 2015 revision 7 GTS rules instead of December 14th, 2011 revision 3. · T1 minimum ride height established at 3.5 inches, measured at rocker panel without driver. · T1 Porsche 928 S4/GTS-R minimum weight reduced to 3200 lbs, throttle restrictor removed. · EP, FP, HP clarified: tapered holes in ball joints now allowed for bolt conversion; wheel bearings and hubs unrestricted at any wheel. · EP open cars may now use aftermarket hardtops if they retain OEM appearance; specific model hardtop allowances removed. · STU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock. · STU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body. · STU suspension rules clarified: alternate components from same manufacturer moved from section E to section D. · STU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold. · STU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules. · TCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019. · STU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight. · Porsche 928 S4/928 GTS-R newly classified in T1 at 3500 lbs minimum with 60mm flat plate restrictor. · EP Mazda RX-7 12A and 13B (79-85) lose up to 80 lbs; 13B (86-91) loses up to 79 lbs. · Honda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork. · STU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances. · STU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed. · STU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10. · STU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options. · STU World Challenge car weight calculation method removed; new basis unclear from text provided. · STU AWD cars no longer required to reduce restrictor 1 mm from table. · STU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each. · T1-LP Ford Mustang GT 5.0L 2018+ classified at 3400 lbs with 65mm flat plate restrictor. · STU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR. · T1-LP Mustang GT350(R) spec line replaced with 2015+ model parameters including 5163cc engine, 3650 lbs curb weight, 315 tire size. · Ford Mustang FP350S (2018) classified in T1-LP at 3600 lbs with 18×11 wheels and 315 tires. · T1 suspension rules clarified: spherical bearings and bushings now explicitly permitted, alternate control arms allowed. · T1 Porsche 996 drops 200 lbs to 3000; 996 GT3 Cup drops 150 lbs to 3000; 997 drops 50 lbs to 3100. · Porsche 997 T1 Maximum now allows OEM PDK transmission alongside existing drivetrain options. · T1 Acura NSX Turbo World Challenge weight to 3100 lbs, restrictor to 44mm. · T1-T3 spec cars receive clarifications on permitted modifications, documentation requirements, and rule conformance; no performance changes.showhide
EP Effective date for Jan 2025 GCR updates #37654inductionslowerEP BMW Z3 2.5L requires 52mm flat plate intake restrictor; Z3 2.8L 55mm; 328i/is E36 58mm; 328i/ci E46 58mm; 325i/is E46 56mm; 325i/is E36 56mm; 325is M-Technic 56mm.
T1 T1 Parity Compared to GT4 #37170weight +125 lbsslowerT1 Mustang gains 125 lbs to 3600, restrictor shrinks 65mm to 60mm. Corvette gains 50 lbs to 3500, restrictor shrinks 70mm to 67mm. BMW deleted.
T1 Clarification of Request Approval #37273 #37399engineunclearT1 E46 M3 Spec Line 1050 allows VAC Motorsports throttle body VAC-TB-S54 on 3.250L engine instead of Dinan.
T1 C8 Corvette Facts #37400weight -100 lbsfasterT1 Chevrolet Corvette C8 (2023-23) minimum weight reduced from 3600 lbs to 3500 lbs.
T1 Camaro Gen 5 Competitive Disadvantage #37440inductionfasterT1 Chevrolet Camaro Gen 5 restrictor increases from 75mm to 80mm flat plate.
T1 Tire Changes in the Rules for GT4 #37497tyres & wheelsunclearT1 Audi R8 GT4 Spec Line #4020 maximum tyre size changes to 315 DOT, 305/645, or 30/65-18 (f), 33/68-18 (r) Non-DOT.
EP Request to Reduce Weight of BMW 325i/is E30 (84-91) Spec Line #37119weight -50 lbsfasterEP BMW 325i/is E30 (84-91) weight reduced 50–52 lbs across three spec lines to 2150, 2204, 2258.
STU Audi 1.8t Wagon STU Table B #36685cars addedfasterSTU Audi 1.8T wagon deleted; Porsche 944 1800 weight to Chart, turbo inlet restrictor removed.
STU Merger GT3 to STU #37486wordingwordingSTU-GT3 reclassified as STU-GT3U effective January 1, 2026.
STU GT3 TCR Tire allowance #37494tyres & wheelsslowerSTU GT3 TCR gains 275-width tire option with 100 lb weight penalty, but not in A compound.
EP Triumph GT6 Adjustments #37112inductionslowerEP Triumph GT6 switches to three Weber 40 DCOE carbs with 28mm chokes, weight rises 50 lbs to 1990.
STU Request to Remove Miata Hubs from General category #37138wordingwordingSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
STU BMW N54/N55 Engine Allowance #37146inductionslowerSTU BMW N54/N55 turbo inlet restrictors now required per GCR definition; turbo swapping prohibited.
T1 Changes to T1 Tires for GT4 and Other Cars #35383tyres & wheelsunclearT1 GT4 tire sizes adjusted across ten cars: most non-DOT rear to 305/660, Audi and McLaren 305/645, Camaro and Mustang 305/680.
T1 G82 M4 GT4 inclusion in T1 #35864cars addedcars addedBMW M4 GT4 (G82) added to T1 GT4 at 3525 lbs minimum weight with Red power stick control.
T1 Alt. Clutch Allowance #36606wordingwordingT1 Spec Lines now permits 5.5 inch clutch in Engine Notes.
T1 BOP Changes Need Updates #36667weight -150 lbsfasterT1 GT4 Spec Line 4020 restrictor opens from 44mm to 45mm, minimum weight drops to 3400 lbs.
T1 Request Ford Performance Darkhorse R in T1 #37136cars addedcars addedMustang Darkhorse R added to T1 homologated cars at 3,250 lbs minimum with 305/315 tires, ineligible for Runoffs until 3 Super Tour events.
T1 Car Mods for T1 Corvette under line item 1150 #37173wordingwordingT1 Corvette may roll or flatten wheel opening lips for tire clearance; plastic fenders may remove lips if edge thickness matches basic material.
T1 Increased Bore Throttle Bodies for E46 M3 S54 Engine #37273enginefasterT1 E46 M3 S54 can now use Dinan Throttle Body #D760-3400 on 3.250L engine.
EP 1275 HP Spridget Level 2 Only #36518enginefasterHP Sprite and Midget 1275cc and 1098cc Level 2 compression ratio raised to 12.0:1.
EP NA Miata Track Width Correction #36902wordingwordingEP Mazda Miata front and rear track widths increased to 1516/1534 mm (59.7/60.4 in.) across all generations.
STU R53 15% Pulley Request #36980inductionslowerSTU Mini Cooper S SC 1900 restricts to 2.565 diameter pulley; 2100 allows 2.285 diameter pulley.
EP Errant entry in HP production line item #36231wordingwordingHP Volkswagen Golf and Jetta 85-92 track correction: front 1537mm (60.5in), rear 1529mm (60.2in).
STU RWD Turbo Disadvantage #36255inductionfasterSTU RWD turbo cars no longer required to reduce restrictor by 1 mm from table.
EP NIssan 300ZX Z31 to EP #35830cars addedcars addedNissan 300ZX 84-89 classified to EP at 2550 lbs minimum, 2960cc 6-cyl SOHC, fuel injection, 12.0:1 compression limit, 0.500" valve lift limit.
EP RX7 1993 and Up Request In EP Spec Lines, classify #36031cars addedcars addedMazda RX-7 92-97 newly classified EP Prep Level 2 at 2200–2310 lbs with 13B 6-port rotary engine.
EP Clean-up Multiple EP RX-8 Spec Lines In EP #36156wordingwordingEP Mazda RX-8 (04-11) alternate spec line removed; one primary line remains.
T1 Please Expedite classing the C63 Mercedes #35987cars addedcars addedMercedes AMG-C63 S (2023) classified in T1 with 4000 lbs minimum weight and 3700 restrictor.
T1 Honda S2000 #35582cars addedcars addedT1 Honda S2000 classified with 2400 lb minimum weight, 2950 cc displacement, 4.75" supercharger pulley.
EP GCR Correction - Redundant HP Spec Lines #35623wordingwordingHP removes four redundant VW spec lines: Rabbit Cabriolet 1780, Scirocco 1588, Scirocco 1780 8-valve, Scirocco 1588.
STU Letter #35397 addendum #35453wordingwordingSTU Mini Cooper S SC: alternate LEAP OMICRON hood scoop LEP-OMICRON3 permitted.
STU S54 Drysump #35464wordingwordingSTU BMW S54 B32 OEM now permits dry sump oiling system.
T1 9.1.9.1 T1 new category item/ line 26 rule to expire Jan 1 2023 #35411cars addedcars addedPontiac GTO 2006-2009 LS1 added to T1 as Spec Line 1590, 5700 cc, 3400 lbs minimum.
EP Update 1988-1991 Civic to Match 1988-1991 CRX #35399weightfasterHP Honda Civic 1.5 (88-91) weight reduced to 2175 lbs base, 2229 lbs with power adder, 2284 lbs with two.
STU ST Electric-Assisted Steering Systems #35066wordingwordingSTL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems.
T1 C8 Corvette T1 Restrictor Plate Request #35213inductionfasterC8 Corvette T1 restrictor plate increases from 70mm to 72mm flat plate.
T1 The Cars Have Expired #35379removedremovedT1 NEW class removes 23 spec lines including Acura NSX, Ferrari, Porsche 996, Nissan Z cars, and others; Porsche 997 spec line 1680 expiration removed.
EP Request to Review Z3 2.5 Spec Line #35073weight +50 lbsslowerEP BMW Z3 2.5L weight increases to 2500 lbs, 2563 lbs with turbo, 2625 lbs with supercharger.
EP Miata Alternate Head #35253weight -50 lbsfasterEP Mazda MX-5 1.8L 1990-97 minimum weight drops to 2150 lbs; 1994-97 variants to 2000, 2050, 2100 lbs respectively.
EP Honda S2000 throttle body #35272inductionfasterEP Honda S2000 fuel injected throttle body inside diameter increases from 62mm to 64mm.
EP Correction within Triumph TR8 Spec Line #35315wordingwordingEP Triumph TR8 dry sump allowance moved from carburetor line to notes section.
EP Correction to EP 924S/944 Spec Line #35317wordingwordingEP Porsche 944/924S 2.5L and 2.7L weight minimums corrected: 2479cc to 2306/2363 lbs, 2681cc to 2358/2415 lbs.
T1 GT4 batch adjustment in T1 #35162other -85 lbsunclearT1-GT4 batch adjustments: five cars lighter, two heavier, restrictors and ECU maps changed, five models now eligible for Runoffs.
EP Porsche 944/924S Rule Change Request #35002cars addedcars addedEP Porsche 944/924S combines 2.5L and 2.7L variants with new weights: 2250–2415 lbs depending on engine and year.
EP Triumph GT6 Adjustments #35054weight -30 lbsfasterEP Triumph GT6 minimum weight reduced to 1800 lbs.
T1 New T1 add spec line for C5 corvette LS2 engines (Copy from C6) #33764cars addedcars addedT1 Chevrolet Corvette C5 LS2 added with 6000cc displacement, 3300 lbs minimum weight, 72mm flat plate restrictor.
T1 C7 Corvette Rule Change Request #34897cars addedcars addedT1 Chevrolet Corvette C7 (14-19) including Z51, Grandsport newly classified as homologated car.
T1 Camaro Gen 5 Weight Reduction Due to Competitive Disadvantage #35092weight -75 lbsfasterT1 Gen 5 Camaro minimum weight drops 75 lbs to 3475; restrictor increases 70mm to 75mm.
T1 Addendum to Letter #35022: Drivetrain Rule #35105wordingwordingT1 Aston Martin Vantage permitted to use OEM Sportshift II transmission.
T1 2004 - 2006 Pontiac GTO Re-Integration Back Into T1 #34403cars addedcars addedPontiac GTO 2006-2009 re-integrated into T1 with LS2 at 3400 lbs, 72mm restrictor, and LS3 at 3500 lbs, 61mm restrictor.
T1 Request to Classify Porsche 997-1 GT3 Cup #34561cars addedcars addedT1 Porsche 997-1 GT3 Cup added at spec line 4210, minimum weight 3050 lbs.
EP Hub Note Clean Up In EP TR8 Spec Line #34649wordingwordingEP Triumph TR8 78-81 removes alternate front hub allowance note; stock hubs now required.
EP Triumph GT6 Adjustments #34662wordingunclearEP Triumph GT6 carburetors change from SU or Stromberg to 1.5" Auto-type.
EP Triumph GT6 Adjustments: Brakes #34663wordingwordingEP Triumph GT6 brakes may now use TR-6 standard or alternate calipers and discs.
T1 Why no Camaro? #34421cars addedcars addedChevrolet Camaro GT4-R classified in T1 GT4 Spec Line 4035, minimum weight 3375 lbs, 315 max tire, 63mm restrictor, ineligible for Runoffs.
T1 Request to Remove Expiration from T1 spec lines #1350 & #1370 #34470wordingwordingT1 Dodge Viper ACR / SRT RT-10 and ACR/ACR-X spec lines 1350 and 1370 remove 12/23 expiration.
T1 Remove #34475wordingwordingT1 GT4 McLaren 570S, Mercedes AMG GT4, and Porsche 718 Cayman GT4 CS MR now eligible for Runoffs competition.
T1 Error in T1 GT4 numbering scheme- #34578wordingwordingT1 GT4 BMW M4 Spec Line Number changed from 4050 to 4030.
T1 C5 Approved Aero That Was Mistakenly Deleted #34374aerofasterT1 Corvette C5 gains approved aero parts: carbon rear spoiler, vented front splitter, side skirts, with 50 lb weight reduction allowed.
EP Correct Intake Valve Size on 1500cc Midget/Spitfire #34419wordingwordingFP and HP Sprite, Midget, and Spitfire 1500 intake valve size corrected to 36.6/(1.44).
STU 2022 Toyota GR Cup for STU #34449cars addedcars addedToyota GR Cup and GR86 Cup (2022-) newly classified in STU at 2700 lbs with 2387 cc engine.
T1 Viper Cleanup #34107inductionfasterT1 Dodge Viper ACR/ACR-X restrictor increases from 50mm to 60mm flat plate.
T1 Viper 8300 OEM FPR Size #34268inductionunclearT1 Dodge Viper ACR/ACR-X: Spec Line 1370 restrictor increases to 55mm, Line 1390 decreases to 55mm.
T1 Ford Mustang S197 (05-14) Clarification #34450wordingwordingT1 Ford Mustang S197 05-14 now requires OEM 8.8 differential housing.
T1 Gen 5 Camaro Engine #33875cars addedcars addedT1 Chevrolet Camaro Gen 5 LS7 gets two spec lines: 1131 with 70mm restrictor, 1136 with 53mm restrictor, both 3450 lbs minimum.
T1 Inquiry to letter #33682 #34071engineslowerT1 Chevrolet Camaro Gen 5, Corvette C5 and C6: engine resleeve restricted to stock parameters only, no longer LS3 bore/stroke.
EP 914-6 Valve Size Correction #34185enginefasterEP Porsche 914-6 2.0L intake valves increase to 2.0 mm, exhaust valves corrected to 38.0 mm.
T1 Request to reinstate T1 S197 Mustang #34048cars addedcars addedT1 Ford Mustang S197 (05-14) reinstated with 3550 lbs minimum weight, 75mm restrictor, Voodoo engine permitted.
T1 T1 GT4 adjustments #33786wordingwordingT1 GT4 weights clarified for nine cars, ranging from 3200 lbs Porsche 718 Cayman to 3575 lbs Aston Martin.
T1 Touring 1 Tire Sizes #34191tyres & wheelsfasterT1-GT4 McLaren 570S and Mercedes AMG GT4 front tires widen to 315 mm.
EP Investigate Parity of Z3 #33343inductionslowerEP BMW Z3 2.5L intake restrictor reduced from 58mm to 56mm flat plate.
STU Alternate OEM Miata Intake Manifold #33827wordingwordingSTU Mazda BP5A classified at 1839 cc maximum displacement, 2023-04-01.
T1 Clarification for Camaro Gen5 2010-2015 #33739inductionslowerT1 Chevrolet Camaro Gen5 LS3-6160 adds 70mm flat plate restrictor, weight 3550 lbs.
STU E&O STU NA Weight Chart. #33737weightfasterSTU minimum weight chart updated: 2450cc to 2595lbs, 2600cc to 2710lbs.
T1 Sequential Gearbox Limitations in T1 #33691wordingwordingT1 cars with aftermarket sequential transmissions get 10-inch max bellhousing; non-sequential cars gain 100 lbs weight break.
T1 T1 GT4 adjustments #33786weightfasterT1 GT4 all nine cars lose 125 lbs minimum weight with driver, from 3200–3575 to 3075–3450.
T1 Sunset of pre 2023 Touring 1 Rules. #33916wordingwordingT1 removes GCR Section 9.1.9.1.A. and T1 Spec Lines entirely, sunsetting pre-2023 Touring 1 rules.
T1 Corrections to T1 Spec Lines #33678tyres & wheelsunclearGT4 McLaren 570S maximum tire size changes to 285 front, 315 rear.
EP Revise 79-85 RX7 Brake Spec Line Allowance #33293wordingunclearEP 79-85 RX-7 12A/13B brake spec simplification removes hub/rotor weight minimum allowance.
EP Request alternate carburetors for EP 280z #33405wordingwordingEP 280Z carburetor option adds Hitachi-SU 1bbl 46mm throttle bores alongside fuel injection.
EP Fuel Injection 12a Mazda RX3 #33434inductioninductionEP Mazda RX-2, RX-3, RX-4, and 12A RX-7 now allow 2 bbl fuel injected throttle body w/ 42mm chokes on dual-y manifold.
EP Mazda RX3 - Weight Reduction #33436weight -50 lbsfasterEP Mazda RX-2, RX-3, RX-3SP, and RX-4 minimum weights reduced 50–52 lbs across all spec lines.
EP Request TR8 Dry Sump Allowance #33460enginefasterEP Triumph TR8 78-81 now allowed to run dry sump.
EP Review Limited Prep Port Matching Rules #33600wordingwordingEP, FP, HP cylinder head ports limited to 1 inch maximum depth matching from mating surface.
EP 280ZX Classification Request #33611cars addedcars addedEP Prep 280ZX (79-83) added to spec lines with 2425–2546 lbs, 2760cc SOHC 6-cyl, fuel injection, 12.0:1 compression limit, .500" valve lift limit.
T1 GT4 section to Current T1 Rules. #33632cars addedcars addedEight GT4 models added to T1 with weights from 3200 to 3575 lbs and restricted power per SRO 2022 rules.
EP Request to classify VW New Beetle 2.5L in EP #32725cars addedcars addedVW New Beetle 2.5L 5-cyl added to EP at 2400–2520 lbs, 2480 cc, fuel injection, comp ratio 12.0:1 max, valve lift 0.500" max.
EP Request Rotary Injection on Dual Y manifold #32775inductionunclearEP Mazda RX-7 12A/13B gains fuel injection option on dual-y manifold with 42mm choke(s).
EP Request for Corrado Stroke & Displacement Correction #32985wordingwordingEP VW Corrado 92-95 stroke corrected to 90.3 mm, displacement to 2792 cc.
STU Request Mazda 13 B turbo #32668cars addedcars addedSTU Mazda 13B Turbo classified, streetport only, stock turbos prohibited, alternatives allowed.
STU Hood Vents and Intercooler Scoops #32733aerofasterSTU OEM louver vents now exempt from vent count and 200 square inch allowance.
STU Non 4 valve weight reduction removed #32808enginefasterSTU 2400cc non-4-valve engines gain 9% base weight reduction; DI turbo prep limits removed.
T1 Correct Camaro Spec Line From Letter #30791 response to 3475lbs #32824weight -25 lbsfasterT1 Cadillac CTS/CTS-V, Chevrolet Camaro, Pontiac Firebird, Pontiac GTO 6162 OEM minimum weight reduced to 3475 lbs.
STU Error in new minimum weight table when combined with other text #32711engineslowerSTU normally-aspirated 2976–3200 cc single-throttle engines lose 10% base engine weight reduction.
STU Redundant Language in May GCR #32713wordingwordingST redundant language removed from balance shaft and pulley modification rules.
EP Subaru BRZ Model Years #32500wordingwordingEP Subaru BRZ and Toyota 86/Scion FR-S model year ranges updated to 13-20.
T1 Fix FP350S limited prep and Shelby 350 full prep issues #31680inductionfasterT1-LP Ford Mustang FP350S restrictor increases from 70mm to 75mm.
T1 Request to Classify AMG GT4 #32610cars addedcars addedMercedes Benz AMG GT4 2017-2021 classified T1 Maximum at 3400 lbs minimum weight with HP-controlled SRO Power Level 2 engine.
EP EP MX-5 Global Cup Car #32218weightslowerEP Mazda MX-5 Global Cup 16-22 minimum weight set to 2400 lbs; sequential gearbox allowed with +150 lbs penalty.
EP Please Class BMW 128i in EP #32370cars addedcars addedBMW 128i (08-13) classified in EP at 2700 lbs minimum with stock throttle body, 11.0:1 compression ratio, 0.400 in. valve lift limits.
EP Inconsistency in Body Work Descriptions #32396aerofasterEP/FP/HP open cars may now use carbon fiber hardtops if they retain OEM appearance in all exterior profiles.
STU Opposed to the Proposed STU Weight Chart #32381wordingwordingSTU cars that qualified for 9 inch wheels in 2021 may continue through 2022 only.
STU Clarification request for GCR 9.1.4.D.3.a Splitter Definition #32414wordingwordingSTU splitter definition clarified: must be single-plane with no vertical deviations, attached to lowest front point.
EP Mazda RX8 with 13b Rotary #32170wordingwordingEP Mazda RX-8 13B carburetor rules clarified: dual 2bbl carb, fuel injected throttle body, or stock fuel injection permitted.
EP Request Idle control valve clarification #32178wordingwordingEP and FP Production clarifies idle control valve rules: stock devices allowed original, removed with blocked ports, or mechanical replaced with electronic stock type.
STU Request Adjustment to Min Weight for STU BMW E36 M3 (95-99) #31535weight -90 lbsfasterSTU BMW S52B32 minimum weight drops 90 lbs to 3110; max displacement cut to 3152 cc.
STU BMW E36 M3 Canadian (North American) S50B32 engine #31866cars addedcars addedSTU BMW S50B32 Euro classified at 3201 cc displacement, 3300 lbs minimum weight.
STU Engine Swap Origin Country #32209wordingwordingST engine swap origin country requirement changes from North America to the United States for case-by-case approval.
STU CRX/Civic Del Sol #32214weightslowerSTU Honda CRX (84-91) and Civic Del Sol (93-97) ineligible for front wheel drive weight reductions.
STU Error correction #32383tyres & wheelsfasterSTU vehicles at or over 2950 lbs base weight may use 9 inch wide wheels instead of 8.0 inch maximum.
STU Single TB Weight Modifiers Add to Chart #32393weightfasterSTU minimum weights reduced: 2450cc to 2596 lbs, 2500cc to 2635 lbs, 2550cc to 2675 lbs.
T1 Viper/Z06 Parity #31942weight -50 lbsfasterT1 Dodge Viper ACR displacement rises to 8400 OEM, minimum weight drops to 3550 lbs.
T1 Discrepancy in T1 allowances #32293wordingwordingT1 Limited T1 wording changed to clarify all T1 cars permitted specifications.
EP EP Adjustments #31858inductionslowerEP BMW Z3 2.5L intake restrictor reduced from 59mm to 58mm flat plate.
EP 1999 3.8L Ford Mustang to EP? #31635weightfasterFord Mustang 99-03 classified to EP at 2700/2768/2835 lbs; 94-98 Mustang weight reduced to 2550/2614/2678 lbs.
EP Improved Touring Tires #32064tyres & wheelstyres & wheelsEP, FP, HP Improved Touring cars may use any DOT-approved tire per section 9.3.45 in Production class.
STU Single TB Weight Modifiers #31449weightfasterSTU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed.
STU Request to Remove A4 1.8t from STU Spec Line Tables #31465weightslowerSTU Audi A4 1.8T minimum weight fixed at 3050 lbs, VF30 turbo with 35mm restrictor now required only.
STU Improved Touring Tires #32063tyres & wheelstyres & wheelsSTL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements.
EP Throttle Body and Idle Air #31800wordingwordingEP, FP, HP classes allow stock/original idle control devices unmodified or completely removed with openings blocked.
EP Porsche 968 Engine Questions #31831otherotherEP Porsche 968 (92-95) now allows dry sump.
EP Request weight reduction for 1979-1985 Mazda RX-7 #31833weightfasterEP 1979-1985 Mazda RX-7 12A and 13B weight reduced by 50-53 lbs across all configurations.
STU Request Allowance for Balance Shaft Delete in STU #31434enginefasterSTU engines may delete balance shafts and plug openings; alternate pulleys allowed for timing belt or chain operation only.
STU Request Louvers in hood vents #31916aeroaeroSTU hood vents allowed to include louvers within 200 sq. inch area.
EP Porsche 968 Engine Questions #31478enginefasterEP Porsche 968 intake valve size increased from 37 to 39.0 mm.
EP PCS E. 2. n. 4. Add Axle Shaft to Allow FWD the Same Freedom #31592wordingwordingEP, FP, HP front-wheel-drive cars may alter body and suspension to install alternate transmission, transaxle, and axle shaft.
EP BMW Z3 2.5L Spec Line #31724wordingwordingEP BMW Z3 2.5L allows alternate throttle body from 92-95 325i with Turner adapter; head casting 1738400 permitted with specific blocks.
STU Request to Add Honda K23 Spec Line #30682cars addedcars addedSTU adds Honda K23 with 2354cc displacement and minimum weight per chart, K24 block allowed with K23 internals and head.
STU RE: Aug FT letter 30682 #31060enginefasterSTU Honda K23 internals rule relaxed to require only K23 crankshaft, allowing other internal modifications.
STU Throttling Device Clarification #31323wordingwordingSTL and STU piston engines clarified: intake manifold and cylinder head porting remains free.
EP 944S2 Restrictor #31396inductionslowerEP Porsche 944S2 89-91 requires 56mm flat plate intake restrictor; comp ratio max 12.0:1, valve lift max 0.500".
EP Classing Clarification for 1986 Toyota Corolla FX16 #31527cars addedcars addedHP Corolla GTS RWD (84-87) added at 2300 lbs; HP Corolla FX16 FWD (87-88) added at 2260 lbs; old Corolla (84-87) removed.
T1 Turbo Miata Help #31315weight +200 lbsslowerT1 Mazda MX-5 Miata MazdaSpeed minimum weight rises to 2550 lbs, restrictor increases to 42mm.
T1 Fix the T1 Corvette heading #31528wordingwordingT1 Chevrolet Corvette Cadillac XLR classified for model years through 2019.
EP E&O; MR2 Track #31120wordingwordingHP Toyota MR-2 1.6L (85-89) track corrected to 15.47 inches front and rear.
EP Request to Allow F22c Engine for 2000-2003 Honda S2000 #30548cars addedunclearHonda S2000 (00-03) reclassified as EP Prep with F22c engine option: 1997cc or 2157cc, weight 2450–2636 lbs depending on displacement.
EP Request a review of the S14 240SX in EP. #30873weight -200 lbsfasterEP Nissan 240-SX S13/S14 loses 200-210 lbs minimum weight; comp ratio rises to 12.0:1, valve lift to .500.
T1 T1 E46 BOP E&O for Letter # 29970 #30934weight +100 lbsslowerT1 BMW E46/E36/Z3 minimum weight increases to 2700 lbs, 3.4L engine car to 2750 lbs.
EP Lotus/Caterham 7 America Request #30392wordingunclearEP Lotus/Caterham 7 America carburetor changed from IT fuel injection prep to fuel injection.
EP Reclassify Daimler SP 250 #30721cars addedcars addedDaimler SP 250 classified in EP at 2165 lbs with 2548 cc OHV 8-cylinder engine.
STU STU Fender flares #30696wordingwordingSTU fender flare wording clarified: exterior contour of any wheel opening may not change opening size, location or shape from side view.
STU Request weight reduction for 12A bridgeport motor in Miata #30751weight -200 lbsfasterSTU Mazda 12A Bridge Port Miata weight reduced from 2550 lbs to 2350 lbs.
T1 Request BoP for the Viper in 1 LP #29968inductionfasterT1 Dodge Viper SRT-10 restrictor increases from 45mm to 57mm.
T1 LS6 Alternative Head Question #30074wordingwordingT1 Chevrolet Corvette Cadillac XLR LS6 engine now permits Casting #799 heads with no other head modifications.
EP Clarify Application of Percentage Based Weight Penalties #30669weightslowerEP, FP, HP clarifies percentage weight penalties sum first, then apply to base weight, rounding to nearest pound.
T1 T1-LP - Add Performance Pack, Bullet, Mach 1 to 18+ Mustang #29849inductionfasterT1 Ford Mustang Shelby/GT350/GT500 5.0L Coyote restrictor opens from 65mm to 70mm flat plate.
T1 Request BoP for the Viper in 1 LP #29968inductionfasterT1 Dodge Viper SRT-10 restrictor increases from 45mm to 57mm.
T1 Request to classify C7 and 13Viper in T1 LP #29969inductionfasterT1-LP Chevrolet Corvette C7 restrictor increases from 70 to 73 mm.
T1 Request LP Z06 steel chassis #30589wordingwordingT1-LP Corvette Z06 06-13 now allows aluminum chassis replacement with equivalent OE steel chassis.
EP Change Classification of 84-87 Mazda 626 from FP to HP #30350cars addedcars added84-87 Mazda 626 reclassified from FP to HP with 2300–2415 lbs weight, 1998cc SOHC, dual 32mm carbs.
EP Fiat X1/9 brake rotors #30423suspension & brakessuspension & brakesFP Fiat X1/9 brake rotors change to 257 (10.1) x 12 (.407) solid disc.
EP NC MX-5 year range correction E&O #30503wordingwordingEP Mazda MX-5 year range corrected from 06-14 to 06-15.
STU Request for Fender Flare Clarification #30375wordingwordingSTU fender flare rules clarified: maximum 2 inches, must cover tire contact patch from above, cannot alter body configuration or wheel opening geometry.
T1 Request For Reduction in Weight/Penalties for Camaro #30443weightfasterT1 Chevrolet Camaro with 6162 displacement minimum weight reduced to 3500 lbs.
T1 Fix dry sump Contradictions in T1-LP vs T2 #30596wordingwordingT1-LP Chevrolet Corvettes C5 Z06, C6 Grand Sport, and Z06 dry sump kit notes clarified to remove contradictions.
EP Please Classify Mazda3 in FP #30165cars addedcars addedMazda 3 S 04-08 classified in EP at 2350 lbs minimum, 2.26L DOHC, 12.0:1 compression, .500" valve lift limit.
STU Provision for Interchangeable Engine Components Already Allowed #30342engineunclearSTU Honda S2000 allows F20/F22 K24 crankshaft with chart weight for achieved displacement.
STU ST Oil Coolers E&O Correction to 9.1.4.2.H #30388wordingwordingST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions.
STU Super Touring Alternate Miata Hubs #30345wordingwordingSTL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs.
T1 T1 LP Aero adjustments #30196aerounclearT1 LP removes 50 lbs weight allowance for stock headers, adds aero device allowance up to 100 lbs, permits headers.
STU Brake Component Relocation #29990wordingwordingST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment.
STU Porsche PDK #30081wordingwordingSTU Porsche PDK automatic transmission limited to 8 forward speeds instead of torque converter restriction.
STU Reference Letter #29333 Proposed STU 13B Spec Line Changes #30086inductionfasterSTU Mazda 13B Street Port 2400 removes choke location restriction, allows auto-type 2bbl with dual-Y manifold.
STU Drive Shaft Request #30087wordingwordingSTU driveshaft and half-shaft materials change from OEM-type to steel or aluminum.
T1 Request to Clarify Miller Mustang Classification #28728engineunclearT1 Ford Mustang Challenge 3-valve maximum displacement changes to 4600/5000.
T1 BMW E46 Carbon Dash #29806weightslowerT1 BMW E46 now allows carbon or fiberglass OEM-style dashboards with 25 pound penalty.
T1 Request to Update T1 Mustang Spec Line #30001wordingwordingT1 Ford Mustang/Thunderbird limited to Shelby/Shelby GT350/GT500 models through 2018.
T1 Class BMW M2CS Club Sport #30195cars addedcars addedBMW M2CS Club Sport classified in T1-LP Spec Lines effective 2021-02-01.
T1 997.1 GT3 Cup #30229cars addedcars addedPorsche 997.1 GT3 Cup (2006-2011) classified in T1 at 3600cc, 3150 lbs minimum weight.
EP Alternate Front Brake Rotors and Calipers for EP AH 3000 #29893suspension & brakessuspension & brakesEP Austin-Healey 3000 Mk. I, II, III now allows TR-6 front calipers and discs as alternate.
STU 13B Rules Adjustment #29333cars addedslowerSTU Mazda 13B Street Port classified at 2400 lbs minimum weight, replacing peripheral and bridge port variants.
T1 Correct T1 Limited Prep Years #29708wordingwordingT1 Chevrolet Corvette Z06 years extended from 06-12 to 06-13.
EP Mk2 VW Consistency and Cleanup of FP and HP Spec Lines #29195weight -50 lbsfasterFP Volkswagen Golf and Jetta 1.8 lose 50 lbs each, to 1900. HP Jetta GLI engine code removed.
EP Correct Wording for Level 1 and Level 2 Induction Systems #29406wordingwordingEP, FP, HP Level 1 and Level 2 induction systems: clarified carburetor and fuel injection rules, jets/needles/rods unrestricted in Level 2.
EP Weight Reduction for Datsun Roadster #29409weight -75 lbsfasterEP Datsun SRL 311U Roadster minimum weight reduced to 1925 lbs from 2000 lbs.
EP EP TR8 Adjustment #29512weight -100 lbsfasterEP Triumph TR8 78-81 weight reduced from 2600 to 2500 lbs.
STU Request clarification on wing measurement #29640aeroaeroST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch.
T1 Changes to Corvette C8 #29898tyres & wheels -100 lbsfasterT1 Corvette C8 Z51 gets wider wheels and tyres, weight drops 100 lbs to 3550.
EP 84-87 Toyota Corolla HP Wheel Diameter Allowance Proposal E&O #29458tyres & wheelsfasterHP 84-87 Toyota Corolla wheel diameter increases from 13 to 15 inches.
STU Request for Advanced Aero Rule Wording Clarification. #29124wordingwordingSTU fender flare rules reworded: up to 2" per corner allowed with 1% weight penalty total.
EP EP BMW Z3 Rule Clarification #28998wordingwordingEP BMW Z3 2.5L iron block casting 1738566-C designation removed, wording clarification only.
STU Minimum Weight Determination #27695wordingwordingSTL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments.
STU ST Gurney flap Wicker clarification #29012wordingwordingSTL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change.
EP Request to Classify Porsche 911 2.0L #28456cars addedcars addedPorsche 911 S 67-68 classified in EP at three weight levels: 1800, 1845, or 1890 lbs.
STU Request for Alternate Intake Manifold #26514wordingwordingSTU request for alternate intake manifold denied; no rule change issued.
STU Request for Addition to GT3 Approved Turbo List #27576wordingwordingGT3 and STU add Borg-Warner EFR6258 to approved turbocharger list.
STU Request BoP for my Car #29004wordingwordingSTU large displacement turbo engines limited by GCR turbo list; non-turbo trim suggested as more competitive.
STU Sequential Shifters in STU #29031wordingwordingSTU sequential shifters referred to Board of Directors for approval; no change implemented yet.
EP BMW Cylinder Head Casting and Part Numbers #28708engineslowerEP BMW 2.8L, 328i E36/E46, and 325i E36 blocks now iron only; 325i E46 aluminum only.
STU Rotary Help #27833cars addedcars addedSTU Mazda 13B Bridge Port and Street Port engines added with 2550 and 2250 lbs minimum weights respectively.
T1 Consider coil spring conversion Corvette in T2 #28824suspension & brakessuspension & brakesT1 and T2 Corvettes may convert leaf spring suspension to coilover with 800 lb max spring rate allowed.
EP Request to Classify 1990-1994 Mazda Protege #28381cars addedcars added1990-1994 Mazda Protege classified in FP Pre at 2150–2258 lbs with 1839cc DOHC engine, fuel injection.
EP Error in Mini Cooper Spec Line #28713wordingwordingHP Mini Cooper model year ranges for convertibles revised: 02-06 now includes 05-08, 07-13 now includes 09-15.
T1 Additional Clarification on 996 Cup in T1 From Letter #28040 #28060wordingwordingT1 Porsche 996 GT3 Cup eligible model years changed from 2002-2005 to 1998-2004.
T1 Request SPEC Corvette Rear Spolier #28182aeroaeroT1 Corvette and Cadillac XLR permitted to install SCRSPLR-001 rear spoiler with OE bodywork.
T1 T1 Rear Brake Rotor Size Exemption for Gen 5 Camaro #28402wordingwordingT1 Gen 5 Camaro allowed 366mm OEM rear rotor and caliper without weight penalty.
EP Caterham 7 Spec Line #28498wordingwordingEP Caterham 7 Spec Line removes redundant suspension note, clarifies engine prep limits and comp ratio to 10.0:1.
STU Request to approve Honda S2000 HKS supercharger #27281enginefasterSTU Honda S2000 adds HKS Supercharger kits 12001-AH006 and 12001-AH010 as allowed.
STU Request BoP on the Lotus #27637weight +100 lbsslowerSTU Lotus Elise Cup R and SC models, plus Exige SC, gain 100–200 lbs minimum weight.
STU Turbo Inlet Restrictor On MK5 Volkswagen #27704inductionslowerSTU Volkswagen GTI/GLI MK5 and Jetta Mk4 may install turbo inlet restrictor in OEM turbo inlet housing.
STU Honda K20C1 removal #27732inductionslowerSTU Honda K20C1 Turbo I4 restrictor reduces from 36mm to 35mm.
STU Change GM LNF 2.0 Allowance to LSJ Engine for Viable STL 2.0 #27884engineslowerSTU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs.
STU Alternate Engine for Porsche 944 #28259engineunclearSTU Porsche 944 now permits VW/Audi 1.8L and 2.0L turbo engines as alternates.
T1 Request 996 GT3 Trunk for Wing Allowance. #28153wordingwordingT1 Porsche 996 Spec Lines now allows 996 Cup Replica Rear deck lid.
T1 All Touring, Change DOT Tire Language 9.1.9.1, 9.3.45 #28452wordingwordingT1 Acura NSX Turbo World Challenge and Audi TTRS GTS 2011 now require DOT tires per GCR section 9.3.
EP Request to Review Horsepower Parity #27662engineslowerEP BMW Z3 2.5L compression ratio capped 12.0:1, valve lift .500, 59mm restrictor required; Z3 2.8L same limits added; 944S2 compression 12.0:1, valve lift .500, 56mm restrictor required.
EP E36 (92-95) Brakes Errors and Omissions #28058weightfasterEP BMW 325is M-Technic loses 100–105 lbs across three weight configurations, to 2550–2678.
EP Request to allow 40 DCOE carb for the Datsun 510 #28195inductionfasterHP Datsun 510 gains 40 DCOE carburetor option alongside existing 40 DCN and 36mm DCNVH choices.
EP Add Throttle Body Size these EP BMW Spec Lines #28422inductionslowerEP BMW fuel injected throttle body maximum inside diameter set to 64mm.
STU Please Modify the STU Wheel Size Rule for Clarity #27694weightfasterSTU vehicles over 2951 lbs base weight may use 9 inch wide wheels, up from 2950 lbs.
STU Turbo Engine Cars Base Weight #28032wordingwordingSTU turbocharged engines now use base weight instead of minimum weight, with 3% DI increase applied to base weight.
T1 Request for E46 wagon with S54 engine in T1 #27427wordingwordingT1 BMW E46 wagon with S54 engine allowed; displacement corrected from 3200 to 3250cc.
EP Request for Help for Datsun 1200 #27934inductionfasterHP Datsun 1200 carburetor choke size increases from 26mm to 30mm.
T1 Request to include Subaru WRX/STI 02-18 in T1 #24916cars addedcars addedT1 adds Subaru WRX/WRX STI 2005-2020 at 3000 lbs minimum weight with 46 mm restrictor.
T1 Request Ford Mustang FP350S T1-LP weight and restrictor change #26662weight +100 lbsslowerT1 Ford Mustang GT (15-17) and GT5.0L (2018-) weight raised to 3500 lbs; Brembo BBK 380mm now at no penalty; restrictors removed from notes.
T1 Request to classify Ford Coyote 3rd Gen OEM #27145cars addedslowerT1 Ford Mustang/Thunderbird 5000 Coyote OEM reclassified to include 2015–2017 and 2018+ model years with 65mm restrictor for 18+.
T1 Request alternate dashboard #27276weightslowerT1 BMW M3 E92 carbon dash allowed with 25 lb penalty.
T1 Request for Allowance of Coil Springs on Limited Prep C6 Corvette #27713suspension & brakesfasterT1 Corvette C5 Z06, C6 coupe, C6 Grand Sport, and Z06 may convert leaf springs to conventional coilover suspension.
EP Request to List Mazda Miata Throttle Body Size #27907wordingwordingFP and EP Mazda Miata models standardized to 55mm throttle body diameter; brake spec clarified.
EP Re-organize Prep2 Cylinder Head Rules for Clarity & Consistency #27661wordingwordingEP, FP, HP cylinder head rules reorganized for clarity; no performance change.
STU Request for an electronic throttle body #27342wordingwordingSTU cars with manual OEM throttle bodies may convert to OEM electronic throttle body of same inner diameter.
EP Request bodywork for Austin Healey Bugeye Sprite MK1 #27106wordingwordingFP and HP Austin-Healey Sprite Mk I and MG Midget variants may replace rear bodywork aft of cockpit with stock-appearing alternate material components.
EP Request to classify the GMX5 2019 #27263wordingwordingEP Mazda MX-5 Global Cup classification year changes from 16-18 to 16-19.
EP level one susp. component rule #27270wordingwordingProduction suspension rule clarifies spindles, hubs, bushings, bearings, ball joints unrestricted.
EP Clarification of Carb Rules - Prep 1 #27300wordingwordingProduction carb rules clarified: carburetor options, fuel injection throttle body dimensions, and intake manifold restrictions reorganised and refined.
EP Clarification of Carb Rules - Prep 2 #27301wordingwordingEP, FP, HP carburetors clarified: jets, needles, metering rods, needle valves unrestricted; choke parts removable; permitted optional carburetors listed.
STU Request to correct E&O advanced aerodynamics #27290wordingwordingSTU wing assembly wording corrected: no part higher than roof height.
T1 T1 LP 2016 Camaro and Later #27198weight -100 lbsfasterT1-LP Chevrolet Camaro 1LE 2016- weight drops to 3500 lbs, restrictor increases to 70mm flat plate.
EP Request Miata Eligibility - 2003 #27121cars addedcars addedEP Mazda MX-5/Miata eligibility years expanded from 1999-2002 to 1999-2005.
T1 Request to return Ford Mustang Challenge Car to T1 #26751cars addedcars addedFord Mustang Challenge returns to T1 as E&O, 4600 cc, 3300 lbs minimum, no restrictor.
T1 Correct years in T1 FP Corvette spec #27023wordingwordingT1 Chevrolet Corvette Cadillac XLR year range corrected from 04-09.
STU Remove -2mm penalty from SR20DET Nissan #26982enginefasterSTU Nissan SR20DET removes -2mm penalty in Table B.
STU Request clarification for manifold and throttle in STU #27004inductionfasterSTU alternate intake manifolds now allowed case-by-case instead of prohibited.
T1 Request BoP Baten - T1 Camaro - Follow up to Letter # 26145 #26900inductionfasterT1 Camaro, CTS, Firebird, GTO restrictor increases from 67mm to 70mm flat plate.
STU Request to clarify afterrmarket side skirts exhaust exit #26814wordingwordingSTU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement.
STU Wheel Flare wording #26872wordingwordingSTU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty.
T1 Clarify DOT tires touring #26556tyres & wheelstyres & wheelsT2-T4 clarifies DOT tire requirements; must have minimum U speed rating and be DOT certified; touring spec line supersedes other rules.
EP Allow Firewall Modification for Fitment of 13B into RX8 #26726wordingwordingEP Mazda RX-8 firewall modification allowed for 13B engine fitment in stock location.
STU Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld.
T1 Request to Classify EcoBoost Mustang #25841cars addedcars addedFord Mustang EcoBoost 3.5L classified in T1 at 3300 lbs minimum weight with 31mm restrictor.
T1 Request Corvette aerodynamic aids #26265aeroslowerT1 Corvette C5 body allowed C7 carbon aero parts, plus 50 lbs.
T1 Audi TTRS VTS Documentation Revision #26578wordingunclearT1 Audi TTRS must conform to July 24th, 2015 revision 7 GTS rules instead of December 14th, 2011 revision 3.
T1 Request Ride Height Clarification #26599wordingwordingT1 minimum ride height established at 3.5 inches, measured at rocker panel without driver.
EP Rollcenter Correction Clarification #25873suspension & brakesfasterEP, FP, HP clarified: tapered holes in ball joints now allowed for bolt conversion; wheel bearings and hubs unrestricted at any wheel.
EP Hardtops #26476wordingwordingEP open cars may now use aftermarket hardtops if they retain OEM appearance; specific model hardtop allowances removed.
STU Request to Use Japanese Mazda 13b Intake Manifold #25790inductionfasterSTU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock.
STU Request Alternate Intake for Mazda MZR In a Rear Wheel Drive App. #26352inductionunclearSTU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body.
STU E&O Suspension #26424wordingwordingSTU suspension rules clarified: alternate components from same manufacturer moved from section E to section D.
STU Revisit B20 VTEC #26530enginefasterSTU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold.
STU Move Flared Fenders to STU Advanced Aero #26564aeroaeroSTU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules.
STU TCA Civic SI E&O #26606tyres & wheelsslowerTCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019.
STU S54 Spec line #26620wordingwordingSTU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight.
T1 Request to classify the Porsche 928GTS/S4 in Touring 1 #26315cars addedcars addedPorsche 928 S4/928 GTS-R newly classified in T1 at 3500 lbs minimum with 60mm flat plate restrictor.
EP Request for Competition Adjustment for 2nd Generation RX7 #25935weight -50 lbsfasterEP Mazda RX-7 12A and 13B (79-85) lose up to 80 lbs; 13B (86-91) loses up to 79 lbs.
STU Request to Class Assignment for 2017 Civic #24287cars addedcars addedHonda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork.
STU Request to run E46 3246cc in STU #25126cars addedcars addedSTU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances.
STU Engine Classification for Rotary #25564wordingunclearSTU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed.
STU K24/K20 Head Swap Clarification/Amendment #25899wordingwordingSTU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10.
STU Request to Classify 12a Bridge Ported Rotary Engine #25985cars addedcars addedSTU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options.
STU World Challenge Car Eligibility #26387wordingunclearSTU World Challenge car weight calculation method removed; new basis unclear from text provided.
STU Request a phone call for discussion regarding weight #26398inductionfasterSTU AWD cars no longer required to reduce restrictor 1 mm from table.
STU Advanced Aero E&O #26413aeroaeroSTU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each.
T1 Request Mustang GT Limited Prep 2018 Classification #24431cars addedcars addedT1-LP Ford Mustang GT 5.0L 2018+ classified at 3400 lbs with 65mm flat plate restrictor.
STU Request to Equalize Direct Injected Turbo Cars #24890cars addedcars addedSTU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR.
T1 Class 2015+ Mustang GT350(R) #21466wordingwordingT1-LP Mustang GT350(R) spec line replaced with 2015+ model parameters including 5163cc engine, 3650 lbs curb weight, 315 tire size.
T1 Request to Classify Ford FP350S in T1-LP #25341cars addedcars addedFord Mustang FP350S (2018) classified in T1-LP at 3600 lbs with 18×11 wheels and 315 tires.
T1 Amendment to Request #25555 #25556wordingwordingT1 suspension rules clarified: spherical bearings and bushings now explicitly permitted, alternate control arms allowed.
T1 Request to balance 996 v 997 T1 weight #25658weightfasterT1 Porsche 996 drops 200 lbs to 3000; 996 GT3 Cup drops 150 lbs to 3000; 997 drops 50 lbs to 3100.
T1 Request to Add PDK Transmission to 997 Porsche Spec Line #25668wordingwordingPorsche 997 T1 Maximum now allows OEM PDK transmission alongside existing drivetrain options.
T1 T1 World Challenge/Grand AM Spec Cars #25687weightslowerT1 Acura NSX Turbo World Challenge weight to 3100 lbs, restrictor to 44mm.
T1 Add Clarification to Spec Car Classifications Vehicle Spec #25774wordingwordingT1-T3 spec cars receive clarifications on permitted modifications, documentation requirements, and rule conformance; no performance changes.
Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of EP" is the class's best as a share of EP's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when EP's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.