FA vs GT1 vs STU pace at Buttonwillow Raceway Park
Quickest here:FA 1:35.792 Greg Labadie, Cal Club 2026 qualifying · GT1 1:39.857 Michael McAleenan, Cal Club 2026 qualifying · STU 1:50.913 Tony Rivera, Cal Club 2026 qualifying
FAGT1STUsolid race · dashed qualifying · slower is lower
FAGT1STUsolid race · dashed qualifying · each class's best lap as a share of FA's at the same event (the reference class, changeable above); 100% is level, higher is quicker
Event
FA
GT1
STU
Qual best
Race best
Trap
Qual best
Race best
Trap
vs FA
% of FA
Qual best
Race best
Trap
vs FA
% of FA
Cal Club 2026 CALCL262026-02-21
1:35.792Greg Labadie · only car-3.750s (-3.77%)
1:37.275Greg Labadie · only car-2.623s (-2.63%)
163.8Greg Labadie+36.4 mph (+28.6%)
1:39.857Michael McAleenan · fastest of 2-4.110s (-3.95%)
1:41.045Michael McAleenan · fastest of 2-1.260s (-1.23%)
167.6Michael McAleenan+53.8 mph (+47.3%)
+3.770squal +4.065s
103.9%qual 104.2%
1:50.913Tony Rivera · fastest of 6 · top 5 within 14.1s-4.488s (-3.89%)
1:52.737Tony Rivera · fastest of 7 · top 5 within 7.7s-0.903s (-0.79%)
135.2Tony Rivera+21.8 mph (+19.3%)
+15.462squal +15.121s
115.9%qual 115.8%
29 rule changes (FA: 7, GT1: 5, STU: 17)8 weight · 7 cars added · 4 induction · 4 tyres & wheels · 2 engine · 1 aero · 3 wording · FA Pro Mazda: lower intake manifold now unrestricted, throttle body raised to 80mm, wing height must not exceed 99cm, bodywork width must not exceed 132cm. · GT1 adds Porsche 992.1 GT3 Cup (2022-2025) with OEM ABS, traction control, RSR bumper, canards, and any exhaust allowed. · FA MZR gains alternate Noor P/N 0088-8-00 intake manifold with AT Power runners as option to Elan or Mazda Speed Elite. · FA Formula 1000 motorcycle-based engine loses maximum compression ratio 14.5:1 limit. · FA Formula 1000 allows carbon fiber external panels, forward-facing gaps, raises floor to 125mm, adds eight 75×125mm rub blocks, expands diffuser to 110cm with 75mm radius transitions. · GT1-ST Acura NSX GT3 EVO 22 weight drops 100 lbs to 3000 lbs. · STU Mazda MZR (LF, L3, L5) Turbo classified; Jack Spania Racing 70 mm intake manifold and Fab9 Tuning bottom-mount turbo kit approved. · STU 36mm restrictor allows 2830 lbs (up 10 lbs from 2820); 37mm allows 2980 lbs (down 5 lbs from 2985). · STU cars over 3150 lbs lose 275-tire option with 2% weight adder. · STU Honda K20 and K24 engines lose 2% minimum weight penalty. · FA class adds USF Pro 2000 car eligibility for Formula Atlantic racing. · STU Honda K24 engine swap weight increases by 2% effective November 1, 2025. · Acura NSX GT3 EVO 22 reclassified from GT1 to GT1-ST with 3100 lbs minimum weight. · GT1 LS Limited Prep Engine expands to include LS1, LS2, LS3, LS6 with 11:1 max compression. · STU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs. · STU-TCR tire width increases to 275 with weight adder raised from 100 to 150 pounds. · STL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs. · FA Ligier JS F3 front tires may be Hoosier 43363 240/580R13 MS, rear 43368 300/590R13 MS. · STU 2.8-3.2L N/A engines now allow 245 max tire width; over 3150 lbs may run 275 with 2% weight penalty. · STU Mazda MZR may use Goodwin 61-2510 or Gato Performance 31972 intake manifold. · STU Honda JDM H23a added, 2259cc displacement, minimum weight per Chart, must meet ST engine regulations. · STU wheel width rules clarified: cars ≤2,850 lbs max 8 inches, cars >2,850 lbs max 9 inches. · STU Spec Line GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tire options clarified with weight adjustments. · FA Formula Renault 2.0 (10-17) spec notes clarified: engine sealed, manual compliance required, tire choice unrestricted, no alterations except repairs. · Acura NSX GT3 EVO 22 classified in GT1 with 3500cc twin turbo V-6, 3100 lbs, max RPM 7500. · STU BMW N54/N55 3.0L classified at Chart +3% minimum weight; N54 twin turbo not allowed. · STU Mini Cooper S SC supercharger pulley diameter reduced from 2.285 to 2.185. · STU Honda K20C1 Turbo I4 exempted from 3% DI weight adder in Spec Lines Table A. · STU GT3U minimum weight increases 150 to 250 pounds.showhide
FA Pro Mazda Classification and Performance Enhancement Proposal #39411inductionfasterFA Pro Mazda: lower intake manifold now unrestricted, throttle body raised to 80mm, wing height must not exceed 99cm, bodywork width must not exceed 132cm.
GT1 Request for Addition of Porsche 992.1 GT3 Cup into GT1 #39322cars addedneutralGT1 adds Porsche 992.1 GT3 Cup (2022-2025) with OEM ABS, traction control, RSR bumper, canards, and any exhaust allowed.
FA Alternate Intake Manifold for MZR #38223inductionunclearFA MZR gains alternate Noor P/N 0088-8-00 intake manifold with AT Power runners as option to Elan or Mazda Speed Elite.
FA Engine Compression Rule Change Request #39302enginefasterFA Formula 1000 motorcycle-based engine loses maximum compression ratio 14.5:1 limit.
FA Change Formula 1000 allowances #39608aerofasterFA Formula 1000 allows carbon fiber external panels, forward-facing gaps, raises floor to 125mm, adds eight 75×125mm rub blocks, expands diffuser to 110cm with 75mm radius transitions.
GT1 NSX Parity With Other GT3s Let Alone a GT1 Car #39311weight -100 lbsfasterGT1-ST Acura NSX GT3 EVO 22 weight drops 100 lbs to 3000 lbs.
STU Request for Permission on Aftermarket Turbo Kit and Intake #39529cars addedfasterSTU Mazda MZR (LF, L3, L5) Turbo classified; Jack Spania Racing 70 mm intake manifold and Fab9 Tuning bottom-mount turbo kit approved.
STU Turbo Inlet Restrictor Table #38961inductionslowerSTU 36mm restrictor allows 2830 lbs (up 10 lbs from 2820); 37mm allows 2980 lbs (down 5 lbs from 2985).
STU 275 Tire Rule #38983tyres & wheelsslowerSTU cars over 3150 lbs lose 275-tire option with 2% weight adder.
STU STU Honda Engine weight penalty #39375weightfasterSTU Honda K20 and K24 engines lose 2% minimum weight penalty.
FA Re-Consider USF Pro 2000 Car for Formula Atlantic Class #38783cars addedneutralFA class adds USF Pro 2000 car eligibility for Formula Atlantic racing.
STU Non-Homologated Engine Swaps - Specifically K24A2 w/ Honda CRZ #38746weightslowerSTU Honda K24 engine swap weight increases by 2% effective November 1, 2025.
GT1 RM 25-06 GT1 reclassify the Acura NSX GT3 EVO 22 to GT1-ST #39101cars addedneutralAcura NSX GT3 EVO 22 reclassified from GT1 to GT1-ST with 3100 lbs minimum weight.
GT1 Correction to Limited prep LS Chevy engine for GT1 #38902cars addedneutralGT1 LS Limited Prep Engine expands to include LS1, LS2, LS3, LS6 with 11:1 max compression.
STU Lotus Weight Reduction E&O #38919weightfasterSTU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs.
STU STU-TCR Adjustments #38723tyres & wheelsslowerSTU-TCR tire width increases to 275 with weight adder raised from 100 to 150 pounds.
STU Lotus Weight Reduction #38772weight -50 lbsfasterSTL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs.
FA Ligier JS F3 Tire Choice #38434tyres & wheelsneutralFA Ligier JS F3 front tires may be Hoosier 43363 240/580R13 MS, rear 43368 300/590R13 MS.
STU 2.8-3.2L N/A Engine Allowances #38007tyres & wheelsunclearSTU 2.8-3.2L N/A engines now allow 245 max tire width; over 3150 lbs may run 275 with 2% weight penalty.
STU 2006-2015 Mazda Miata Intake Manifold #38422wordingneutralSTU Mazda MZR may use Goodwin 61-2510 or Gato Performance 31972 intake manifold.
STU Requesting Approval of the JDM Honda h23a #38489cars addedneutralSTU Honda JDM H23a added, 2259cc displacement, minimum weight per Chart, must meet ST engine regulations.
STU Wheel Size Inconsistency #38018wordingneutralSTU wheel width rules clarified: cars ≤2,850 lbs max 8 inches, cars >2,850 lbs max 9 inches.
STU Table C: STU-GT3U Clarification #38268weightfasterSTU Spec Line GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tire options clarified with weight adjustments.
FA Update Formula Renault 2.0 spec line notes #37853wordingneutralFA Formula Renault 2.0 (10-17) spec notes clarified: engine sealed, manual compliance required, tire choice unrestricted, no alterations except repairs.
GT1 Request to Classify Acura NSX GT3 Evo 22 #37367cars addedneutralAcura NSX GT3 EVO 22 classified in GT1 with 3500cc twin turbo V-6, 3100 lbs, max RPM 7500.
STU BMW N54/N55 Engine Allowance Follow Up #37447engineneutralSTU BMW N54/N55 3.0L classified at Chart +3% minimum weight; N54 twin turbo not allowed.
STU STU Mini Cooper pulley size clarification re: letter #36980 #37717inductionfasterSTU Mini Cooper S SC supercharger pulley diameter reduced from 2.285 to 2.185.
STU Question About a Weight Modifier #37782weightfasterSTU Honda K20C1 Turbo I4 exempted from 3% DI weight adder in Spec Lines Table A.
STU Increase Minimum Weight #37919weight +100 lbsslowerSTU GT3U minimum weight increases 150 to 250 pounds.
Cal Club 2025 CALCL252025-02-22
1:39.542Greg Labadie · only car
1:39.898Greg Labadie · only car
127.4Greg Labadie
1:43.967Michael Lewis · only car
1:42.305Michael Lewis · only car
113.8Michael Lewis
+2.407squal +4.425s
102.4%qual 104.4%
1:55.401Wilson Powell · fastest of 4 · top 4 within 8.7s
1:53.640Rylan Hazelton · fastest of 5 · top 5 within 8.0s
113.3Rylan Hazelton
+13.742squal +15.859s
113.8%qual 115.9%
189 earlier rule changes on record, in force before Cal Club 2025 (from 2019)33 cars added · 20 weight · 19 induction · 16 engine · 8 aero · 7 tyres & wheels · 1 removed · 85 wording · FA adds Tatuus F.3 T-318 or FR-19 as spec line car in Table 2 for Formula Regional European Championship. · GT1 LS1 Limited Prep engine added, 2600 lbs with driver, 383 cubic inches max, hydraulic roller cam, 750 cfm carb. · TA2 rear wing height rule clarified: OEM aerodynamic devices exempt from peak-of-roof requirement. · GT1-ST restrictor sizes removed for 13 cars; new specs not printed in letter. · STU Audi 1.8T wagon deleted; Porsche 944 1800 weight to Chart, turbo inlet restrictor removed. · STU-GT3 reclassified as STU-GT3U effective January 1, 2026. · STU GT3 TCR gains 275-width tire option with 100 lb weight penalty, but not in A compound. · GT1-ST Lamborghini Huracan GT3 Evo and 2019+ GT3 both shift to Unrestricted from 39mm and 52mm restrictors. · STL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval. · STU BMW N54/N55 turbo inlet restrictors now required per GCR definition; turbo swapping prohibited. · GT1 Mazda 26B engine classified at 2850 lbs minimum weight. · STU Mini Cooper S SC 1900 restricts to 2.565 diameter pulley; 2100 allows 2.285 diameter pulley. · STU RWD turbo cars no longer required to reduce restrictor by 1 mm from table. · GT2-ST Acura NSX minimum weight raised to 3000 lbs, restrictor increased to 45mm TIR. · GT1 Camaro 1993-2002 classification updated; 2010- model separately classified. · STU Mini Cooper S SC: alternate LEAP OMICRON hood scoop LEP-OMICRON3 permitted. · STU BMW S54 B32 OEM now permits dry sump oiling system. · GT1, GT2, GT3, GTL, GTX rear spoiler maximum surface area limit of 295.0 square inches removed. · GT1/GT2/GT3/GTL/GTX Direct Injection now permitted if OE, using only OE pump, hoses, injectors. · GT2/3 Nissan, Mazda, Mitsubishi 4G93, QR25DE/DD, QE25DE/DD Direct Injection now permitted per 9.1.2.F.7.5.E. · STL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems. · Lamborghini Huracan GT3 EVO(1) and GT3 added to GT1-ST at 3000 and 3100 lbs minimum weight respectively. · GT1 Trick Flow Specialties Ultra 18 Degree GM Cylinder Head Part #TFS-3181T001-CO1 allowed. · GTL spec lines moved to contiguous position with GT2 and GT3; GTA category and spec lines renumbered and moved behind GTL. · Toyota GR Cup and GR86 Cup (2022-) newly classified in STU at 2700 lbs with 2387 cc engine. · FA Pro Formula Mazda front wheels widen to 10 in. max; rear wheels narrow to 14 in. min. · FA Pro Formula Mazda maximum bodywork width behind front wheels increases to 51.97 inches. · FA MSR Formula Mazda FMzR added to Table 2 classification. · Fields Cardinal V8 classified in GT1 with Ford V8 engine, 4.9L displacement, 2100 lbs minimum weight. · GT1 Mercedes AMG GT3 16-19 preparation wording changed to per FIA GT3 homologation. · STU Mazda BP5A classified at 1839 cc maximum displacement, 2023-04-01. · STU minimum weight chart updated: 2450cc to 2595lbs, 2600cc to 2710lbs. · GT1 sequential transmission weight penalty reduced from 50 to 25 lbs. · GT1-ST Porsche 992 GT3 Cup classified with 3997cc displacement, 2950 lbs minimum weight. · FA BDA engine displacement specification line added to Table 1, effective 2023-01-01. · Formula Renault 2.0 (10-17) reclassified from FX to FA; weight reduced to 1280 lbs, restrictor removed. · FA Swift 016 2.3L restrictor increases from 31mm to 32mm SIR; minimum weight drops 30 lbs to 1420. · GT2 TA2 and GTA throttle body part numbers updated to GM 90mm electronic #12570790 or Edelbrock 90mm mechanical #33869 or #3870. · GT1 Trans Am bodywork weight penalty reduced from 100 lbs to 75 lbs. · GT1 Chevrolet RO7, Ford FR9, and Dodge R7 weight penalties reduced from 50 to 25 lbs. · Pro Formula Mazda allows street or bridge port, unrestricted apex seals, 70mm throttle body, 99cm wing height max, 132cm bodywork width max. · GT taillights may now be original style or a panel graphic with functioning red LED brake lamps; wording change only. · GT1 TransAm bodywork allowed with 100 lb. weight penalty. · STU Mazda 13B Turbo classified, streetport only, stock turbos prohibited, alternatives allowed. · STU OEM louver vents now exempt from vent count and 200 square inch allowance. · STU 2400cc non-4-valve engines gain 9% base weight reduction; DI turbo prep limits removed. · STU normally-aspirated 2976–3200 cc single-throttle engines lose 10% base engine weight reduction. · ST redundant language removed from balance shaft and pulley modification rules. · FA Ligier JS F3 must comply with Formula Regional Americas rules instead of FIA Formula 3 Regional Technical Regulations. · FA sealed engines must undergo full inspection; competitor pays reassembly and resealing costs. · FA Formula Lites FL15 and FR Americas Ligier JS F3 engine sealing requirements clarified to reference respective series technical regulations. · STU cars that qualified for 9 inch wheels in 2021 may continue through 2022 only. · STU splitter definition clarified: must be single-plane with no vertical deviations, attached to lowest front point. · FA transmission rule clarified: transverse shafts prohibited except final drive and motorcycle gearbox in Formula 1000. · FA Swift 016 2.5 liter aero spec now references 2.3 liter notes instead of N notes. · STU BMW S52B32 minimum weight drops 90 lbs to 3110; max displacement cut to 3152 cc. · STU BMW S50B32 Euro classified at 3201 cc displacement, 3300 lbs minimum weight. · ST engine swap origin country requirement changes from North America to the United States for case-by-case approval. · STU Honda CRX (84-91) and Civic Del Sol (93-97) ineligible for front wheel drive weight reductions. · STU vehicles at or over 2950 lbs base weight may use 9 inch wide wheels instead of 8.0 inch maximum. · STU minimum weights reduced: 2450cc to 2596 lbs, 2500cc to 2635 lbs, 2550cc to 2675 lbs. · FA Pro Formula Mazda now allows street port or bridge port, previously porting was prohibited. · Mercedes Benz AMG GT3 classified in GT1 at 3050 lbs with 40mm restrictors, prepared per FIA GT3 homologation. · GT1 wheels: 18-inch tyres get wider rear allowance, from 13 to 14 MAX inches. · STU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed. · STU Audi A4 1.8T minimum weight fixed at 3050 lbs, VF30 turbo with 35mm restrictor now required only. · STL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements. · FA adds Honda K20Z3 2.0L engine spec at 1350 lbs minimum and Mazda MZR 2.0L spec at 1300 lbs minimum to Table 1. · GT1 allows 17-inch wheels newly; 18-inch wheels require 50 lb penalty; maximum widths 12 front/13 rear, or 13/14 for 18-inch. · STU engines may delete balance shafts and plug openings; alternate pulleys allowed for timing belt or chain operation only. · STU hood vents allowed to include louvers within 200 sq. inch area. · STU adds Honda K23 with 2354cc displacement and minimum weight per chart, K24 block allowed with K23 internals and head. · STU Honda K23 internals rule relaxed to require only K23 crankshaft, allowing other internal modifications. · STL and STU piston engines clarified: intake manifold and cylinder head porting remains free. · GT3 Fun Cup Beetle EVO3 classified with 1984 cc sealed SOHC engine, 2060 lbs minimum weight. · FA Mazda MZR 2.0 spec line removes redundant '2.0' designation; Honda Civic K20Z3 spec line unchanged. · FA Toyota 1800 moves from Table 1 to Table 2 (Spec Line Cars). · FA Swift 016 Mazda MZR/Ford Duratec wheel width specification clarified: front 10, rear 14 minimum and 15 maximum. · GTA part numbers updated: 0-80541-1 to 0-80541-2 in two sections and 6010 to 6014X in TA2 Appendix. · FA rule wording clarified: Table 1 for purpose-built and ex-pro cars, Table 2 for spec line cars with exceptions noted. · FA Mazda MZR/Ford Duratec 2296cc and 2500cc moved from Table 1 to Table 2. · FA Mazda MZR 2.0 and Honda Civic K20Z3 remove sequential designation from 5-speed transmission spec. · STU fender flare wording clarified: exterior contour of any wheel opening may not change opening size, location or shape from side view. · STU Mazda 12A Bridge Port Miata weight reduced from 2550 lbs to 2350 lbs. · FA Mazda MZR 2.0 limited to Ralt RT40, RT41, Swift 008, 014 chassis; Honda Civic K20Z3 removes Swift 016 chassis. · FA Swift 016 2.3 liter engine name corrected to Mazda MZR/Ford Duratec. · FA Swift 016 2.5 liter engine name corrected to Mazda MZR/Ford Duratec. · FA removes four spec lines and replaces Ford Duratec/Mazda MZR with Honda B16 at 1615cc, 1175 lbs minimum. · STU fender flare rules clarified: maximum 2 inches, must cover tire contact patch from above, cannot alter body configuration or wheel opening geometry. · FA Spec Line C loses 25 lbs to 1175; Line I loses 75 lbs to 1175; Line K gains 15 lbs to 1175. · FA purpose built and ex-Pro Atlantic cars lose 25 lb sequential transmission penalty wording. · FA Ligier JS F3 car name corrected in FR Americas spec line. · FA Ford Duratec/Mazda MZR 2500 spec line D wording cleanup: 4-valve becomes 4 valves per cylinder. · FA Honda Civic K20Z3 intake manifold and throttle body assembly now allows AT Power Direct-To-Head 45mm individual throttle bodies as alternative to HPD parts. · STU Honda S2000 allows F20/F22 K24 crankshaft with chart weight for achieved displacement. · ST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions. · FA Ford Duratec/Mazda MZR intake restrictor reduced from 32mm to 30mm SIR; Swift 016 2.5 Mazda restrictor reduced from 35mm to 33mm SIR. · FA Toyota 4A-GE engines cleaned up, spec lines A and B engine designations corrected. · FA Ford BD Series max displacement increases from 1600 to 1615 cc, minimum weight stays 1200 lbs. · FA Ford Duratec/Mazda MZR and Honda B16 both now 1615cc max displacement; Honda B16 removes NA requirement. · FA Pro Formula Mazda engine specs moved from Table 1 to Table 2 notes; Renesis Rotary details consolidated. · FA F3 Americas spec line updated effective 2021-03-01; specific changes not legible in provided text. · STL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs. · ST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment. · STU Porsche PDK automatic transmission limited to 8 forward speeds instead of torque converter restriction. · STU Mazda 13B Street Port 2400 removes choke location restriction, allows auto-type 2bbl with dual-Y manifold. · STU driveshaft and half-shaft materials change from OEM-type to steel or aluminum. · Formula Lites Crawford FL15 newly classified in FA. · STU Mazda 13B Street Port classified at 2400 lbs minimum weight, replacing peripheral and bridge port variants. · ST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch. · GT1, GT2, GT3, GTL, GTX now permit turbocharging/supercharging if listed on spec line. · STU fender flare rules reworded: up to 2" per corner allowed with 1% weight penalty total. · GT1 adds Trans Am spec engines: Chevrolet R07, Ford FR9, Dodge R7, each with 50 lbs. weight penalty. · STL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments. · STL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change. · FA stock engines not given weight adjustment; modified engines now allowed in class. · TA2 Gurney flap wording clarified: terminology standardized to 'Gurney flap', height limits and thickness specifications remain 0.50 inch / 0.625 inch or 0.375 inch / 0.0625 inch depending on configuration. · STO rear wing wording clarified: 'wicker' changed to 'Gurney flap' in maximum chord and mounting height rules. · GT1 Gurney flap wicker clarification: terminology standardized from lips/tabs/wicker to flaps throughout specifications. · GT classes clarify Gurney flap wording, replacing wickerbill/tab terminology with flap; specifications unchanged. · STU request for alternate intake manifold denied; no rule change issued. · GT3 and STU add Borg-Warner EFR6258 to approved turbocharger list. · STU large displacement turbo engines limited by GCR turbo list; non-turbo trim suggested as more competitive. · STU sequential shifters referred to Board of Directors for approval; no change implemented yet. · FA engine modifications wording clarified: bore/crankshaft/stroke/flywheel unrestricted if displacement limit met, distributor/transistor ignition allowed without engine modification, compression ratio increasable by machining/gasket chang… · FA transmission rules clarified: no more than five forward speeds and operational reverse gear unless Table 2 notes otherwise. · FA Swift 016 Mazda Duratec Gurney flap wording clarified; terminology and mounting rules unchanged. · STU Mazda 13B Bridge Port and Street Port engines added with 2550 and 2250 lbs minimum weights respectively. · FA Volkswagen 1835cc SOHC removed from Table 1. · FA engine rules clarified: blocks and heads must be OEM unless Tables note exceptions. · FA Formula 1000 motorcycle-based engine compression ratio raised to 14.5:1 from 13.5:1. · FA removes Ex-FSV front wheel width 6–8 inches and rear 8–10 inches provisions; all cars use front 10 inches, rear 14–15 inches. · FA Formula 3 engines now allowed through 2017, previously 2008, with 30mm restrictor required. · STU Honda S2000 adds HKS Supercharger kits 12001-AH006 and 12001-AH010 as allowed. · STU Lotus Elise Cup R and SC models, plus Exige SC, gain 100–200 lbs minimum weight. · STU Volkswagen GTI/GLI MK5 and Jetta Mk4 may install turbo inlet restrictor in OEM turbo inlet housing. · STU Honda K20C1 Turbo I4 restrictor reduces from 36mm to 35mm. · STU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs. · STU Porsche 944 now permits VW/Audi 1.8L and 2.0L turbo engines as alternates. · FA engine note clarification removes Table E reference, Pro Formula Mazda directed to Table 1. · STU vehicles over 2951 lbs base weight may use 9 inch wide wheels, up from 2950 lbs. · STU turbocharged engines now use base weight instead of minimum weight, with 3% DI increase applied to base weight. · GT1, GT2, GT3, GTL, GTX may omit windshield clips if factory glass is bonded per original specifications. · Formula 1000 motorcycle-based engine classified into FA, throttle bodies and ECUs unrestricted. · F1000 reclassified into FA with specification changes effective 2020-01-01. · FA Swift 016 2.3L Mazda Duratec restrictor reduced from 33mm to 31mm SIR, making it slower. · GT2/ST Ford 5.0L Coyote 3rd Gen OEM added at 3200 lbs with Boss intake manifold permitted. · Factory Five Type 65 Coupe R with Ford 302/351 or 5.0/5.2L NA added to GTX-MISC at 2600 lbs. · GT1 sequential shifting transmission weight penalty reduced from 75 to 50 lbs. · GT1 non-18-inch-wheel cars now get 18-inch wheels with 50 lb penalty, down from 100 lb. · GT1 Spec Lines allows 5 Star NASCAR Camaro 2018+ body for General Motors Corporation. · FA wheel dimension rules moved from Bodywork subsection to General section; no specification changes. · FA Mazda MZR 2.0 now limited to Ralt RT40, Ralt RT41, and Swift 014 chassis only. · STU cars with manual OEM throttle bodies may convert to OEM electronic throttle body of same inner diameter. · FA Honda Civic K20Z3 engines consolidated: three separate base/uprated specs removed, replaced with single unified 1350 lb minimum weight spec for Swift 014/016. · FA Swift 014 Mazda MZR 2.0 piston minimum weight reduced from 320g to 280g. · GT1 Porsche 944/968 classified: 2981cc twin turbo, 2585 lbs minimum weight. · STU wing assembly wording corrected: no part higher than roof height. · GT1 allows Trans Am rear wing, 12" chord, 72" span, 1/2" wicker, 100 sq in endplates, no weight penalty. · STU Nissan SR20DET removes -2mm penalty in Table B. · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · FA Line N minimum weight increases to 1375 lbs. · STU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement. · STU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty. · FA cars must install AIM part #X47KPFSOLO2R0 data box mount for Majors and Runoffs. · GTX tube frame cars gain fuel injection with 90mm maximum throttle body size. · Ligier JS2 R classified in GTX, no performance parameters specified in filing. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · GT1 and GT2/GT3/LITE ride height requirements removed from GCR sections 9.1.2.D.5.a.1 and 9.1.2.F.7.b. · STU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock. · STU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body. · STU suspension rules clarified: alternate components from same manufacturer moved from section E to section D. · STU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold. · STU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules. · TCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019. · STU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight. · FA Formula 3 car sequential gearbox weight penalty of 25 lbs removed; minimum weight now 1215 lbs. · Honda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork. · STU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances. · STU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed. · STU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10. · STU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options. · STU World Challenge car weight calculation method removed; new basis unclear from text provided. · STU AWD cars no longer required to reduce restrictor 1 mm from table. · STU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each. · FA Swift 014-Mazda MZR 2.0 engine now requires OE block casting #LF95 and specific OE components instead of sealed Elite Engines sourcing. · FA Swift 016 Mazda Duratec 2.3L and 2.5L minimum weight increases from 1420 to 1450 lbs. · GTX FIA GT3: Audi R8 40mm restrictor 2900 lbs, BMW Z4 70mm 2800 lbs, Ferrari 488 35mm restrictor 3025 lbs classified. · STU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR.showhide
FA Classify FR European Championship car as spec line car in Table 2 #37658cars addedneutralFA adds Tatuus F.3 T-318 or FR-19 as spec line car in Table 2 for Formula Regional European Championship.
GT1 Addition of a limited prep LS Chevy engine for GT1 #37045cars addedneutralGT1 LS1 Limited Prep engine added, 2600 lbs with driver, 383 cubic inches max, hydraulic roller cam, 750 cfm carb.
GT1 Correct language regarding OEM Areo Devices #37137wordingneutralTA2 rear wing height rule clarified: OEM aerodynamic devices exempt from peak-of-roof requirement.
GT1 GT1-ST Adjustments #37481inductionunclearGT1-ST restrictor sizes removed for 13 cars; new specs not printed in letter.
STU Audi 1.8t Wagon STU Table B #36685cars addedfasterSTU Audi 1.8T wagon deleted; Porsche 944 1800 weight to Chart, turbo inlet restrictor removed.
STU Merger GT3 to STU #37486wordingneutralSTU-GT3 reclassified as STU-GT3U effective January 1, 2026.
STU GT3 TCR Tire allowance #37494tyres & wheelsslowerSTU GT3 TCR gains 275-width tire option with 100 lb weight penalty, but not in A compound.
GT1 Lamborghini Huracan GT3 Evo Restrictor Help #36254inductionfasterGT1-ST Lamborghini Huracan GT3 Evo and 2019+ GT3 both shift to Unrestricted from 39mm and 52mm restrictors.
STU Request to Remove Miata Hubs from General category #37138wordingneutralSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval.
STU BMW N54/N55 Engine Allowance #37146inductionslowerSTU BMW N54/N55 turbo inlet restrictors now required per GCR definition; turbo swapping prohibited.
GT1 Request to Classify Mazda 26B Engine #36230cars addedneutralGT1 Mazda 26B engine classified at 2850 lbs minimum weight.
STU R53 15% Pulley Request #36980inductionslowerSTU Mini Cooper S SC 1900 restricts to 2.565 diameter pulley; 2100 allows 2.285 diameter pulley.
STU RWD Turbo Disadvantage #36255inductionfasterSTU RWD turbo cars no longer required to reduce restrictor by 1 mm from table.
GT1 Request for Spec Line 1010 Reconsideration #35009weight +300 lbsslowerGT2-ST Acura NSX minimum weight raised to 3000 lbs, restrictor increased to 45mm TIR.
GT1 Camaro 1993- and 2010- #35652wordingneutralGT1 Camaro 1993-2002 classification updated; 2010- model separately classified.
STU Letter #35397 addendum #35453wordingneutralSTU Mini Cooper S SC: alternate LEAP OMICRON hood scoop LEP-OMICRON3 permitted.
STU S54 Drysump #35464wordingneutralSTU BMW S54 B32 OEM now permits dry sump oiling system.
GT1 Rear Blade Spoiler Clarification #35261aerofasterGT1, GT2, GT3, GTL, GTX rear spoiler maximum surface area limit of 295.0 square inches removed.
GT1 GT Direct Injection allowance and rules #35437enginefasterGT1/GT2/GT3/GTL/GTX Direct Injection now permitted if OE, using only OE pump, hoses, injectors.
GT1 GT2/3 remove Direction Injection not allowed in Spec line notes #35439inductionfasterGT2/3 Nissan, Mazda, Mitsubishi 4G93, QR25DE/DD, QE25DE/DD Direct Injection now permitted per 9.1.2.F.7.5.E.
STU ST Electric-Assisted Steering Systems #35066wordingneutralSTL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems.
GT1 Request for Acceptance of Lamborghini Huracan GT3 in GT1-ST #34929cars addedneutralLamborghini Huracan GT3 EVO(1) and GT3 added to GT1-ST at 3000 and 3100 lbs minimum weight respectively.
GT1 Cylinder heads #35040wordingneutralGT1 Trick Flow Specialties Ultra 18 Degree GM Cylinder Head Part #TFS-3181T001-CO1 allowed.
GT1 Errors in GTCS Headings and Use of the Terms Category and ClassChange existing GTL and GTA Rules #34453wordingneutralGTL spec lines moved to contiguous position with GT2 and GT3; GTA category and spec lines renumbered and moved behind GTL.
STU 2022 Toyota GR Cup for STU #34449cars addedneutralToyota GR Cup and GR86 Cup (2022-) newly classified in STU at 2700 lbs with 2387 cc engine.
FA Simplify Pro Formula Mazda wheel allowance #34190tyres & wheelsunclearFA Pro Formula Mazda front wheels widen to 10 in. max; rear wheels narrow to 14 in. min.
FA E&O - Correct Pro Formula Mazda spec line dimensional equivalent #34085aerofasterFA Pro Formula Mazda maximum bodywork width behind front wheels increases to 51.97 inches.
FA Add new spec line for MSR Formula Mazda FMzR to Table 2 #34139cars addedneutralFA MSR Formula Mazda FMzR added to Table 2 classification.
GT1 Please classify Fields Cardinal V8 #33784cars addedneutralFields Cardinal V8 classified in GT1 with Ford V8 engine, 4.9L displacement, 2100 lbs minimum weight.
GT1 Mercedes AMG GT3 Notes #33804wordingneutralGT1 Mercedes AMG GT3 16-19 preparation wording changed to per FIA GT3 homologation.
STU Alternate OEM Miata Intake Manifold #33827wordingneutralSTU Mazda BP5A classified at 1839 cc maximum displacement, 2023-04-01.
STU E&O STU NA Weight Chart. #33737weightfasterSTU minimum weight chart updated: 2450cc to 2595lbs, 2600cc to 2710lbs.
GT1 Sequential Transmission Weight Penalty #33503weightfasterGT1 sequential transmission weight penalty reduced from 50 to 25 lbs.
GT1 GT1 Porsche 992 #33730cars addedneutralGT1-ST Porsche 992 GT3 Cup classified with 3997cc displacement, 2950 lbs minimum weight.
FA BDA Displacement #33431wordingneutralFA BDA engine displacement specification line added to Table 1, effective 2023-01-01.
FA Reclassify 2010-2017 Formula Renault 2.0 as a spec line car in FA #33395cars addedfasterFormula Renault 2.0 (10-17) reclassified from FX to FA; weight reduced to 1280 lbs, restrictor removed.
FA Change Swift 016 2.3L restrictor size and minimum weight #33472induction -30 lbsfasterFA Swift 016 2.3L restrictor increases from 31mm to 32mm SIR; minimum weight drops 30 lbs to 1420.
GT1 GT2 (TA2)/GTA Part Number Update #33315wordingneutralGT2 TA2 and GTA throttle body part numbers updated to GM 90mm electronic #12570790 or Edelbrock 90mm mechanical #33869 or #3870.
GT1 Request to Reduce Trans Am Bodywork Weight Penalty #33331weightfasterGT1 Trans Am bodywork weight penalty reduced from 100 lbs to 75 lbs.
GT1 Request for Reduction in FR9 Weight Penalty #33332weightfasterGT1 Chevrolet RO7, Ford FR9, and Dodge R7 weight penalties reduced from 50 to 25 lbs.
FA Pro Formula Mazda Dimension E&O #33160wordingneutralPro Formula Mazda allows street or bridge port, unrestricted apex seals, 70mm throttle body, 99cm wing height max, 132cm bodywork width max.
GT1 Tail lights on all GT category race cars. #32799wordingneutralGT taillights may now be original style or a panel graphic with functioning red LED brake lamps; wording change only.
STU Request Mazda 13 B turbo #32668cars addedneutralSTU Mazda 13B Turbo classified, streetport only, stock turbos prohibited, alternatives allowed.
STU Hood Vents and Intercooler Scoops #32733aerofasterSTU OEM louver vents now exempt from vent count and 200 square inch allowance.
STU Non 4 valve weight reduction removed #32808enginefasterSTU 2400cc non-4-valve engines gain 9% base weight reduction; DI turbo prep limits removed.
STU Error in new minimum weight table when combined with other text #32711engineslowerSTU normally-aspirated 2976–3200 cc single-throttle engines lose 10% base engine weight reduction.
STU Redundant Language in May GCR #32713wordingneutralST redundant language removed from balance shaft and pulley modification rules.
FA Update FR Americas rulebook requirement #32491wordingneutralFA Ligier JS F3 must comply with Formula Regional Americas rules instead of FIA Formula 3 Regional Technical Regulations.
FA Clarify verification of sealed engine compliance #32522wordingneutralFA sealed engines must undergo full inspection; competitor pays reassembly and resealing costs.
FA Clarify Formula Lites and FR Americas sealed engine requirement #32523wordingneutralFA Formula Lites FL15 and FR Americas Ligier JS F3 engine sealing requirements clarified to reference respective series technical regulations.
STU Opposed to the Proposed STU Weight Chart #32381wordingneutralSTU cars that qualified for 9 inch wheels in 2021 may continue through 2022 only.
STU Clarification request for GCR 9.1.4.D.3.a Splitter Definition #32414wordingneutralSTU splitter definition clarified: must be single-plane with no vertical deviations, attached to lowest front point.
FA E&O FA Transmission section #32251wordingneutralFA transmission rule clarified: transverse shafts prohibited except final drive and motorcycle gearbox in Formula 1000.
FA E&O Swift 016 2.5 liter Aero column #32363wordingunclearFA Swift 016 2.5 liter aero spec now references 2.3 liter notes instead of N notes.
STU Request Adjustment to Min Weight for STU BMW E36 M3 (95-99) #31535weight -90 lbsfasterSTU BMW S52B32 minimum weight drops 90 lbs to 3110; max displacement cut to 3152 cc.
STU BMW E36 M3 Canadian (North American) S50B32 engine #31866cars addedneutralSTU BMW S50B32 Euro classified at 3201 cc displacement, 3300 lbs minimum weight.
STU Engine Swap Origin Country #32209wordingneutralST engine swap origin country requirement changes from North America to the United States for case-by-case approval.
STU CRX/Civic Del Sol #32214weightslowerSTU Honda CRX (84-91) and Civic Del Sol (93-97) ineligible for front wheel drive weight reductions.
STU Error correction #32383tyres & wheelsfasterSTU vehicles at or over 2950 lbs base weight may use 9 inch wide wheels instead of 8.0 inch maximum.
STU Single TB Weight Modifiers Add to Chart #32393weightfasterSTU minimum weights reduced: 2450cc to 2596 lbs, 2500cc to 2635 lbs, 2550cc to 2675 lbs.
FA Closing the Gap #31934inductionfasterFA Pro Formula Mazda now allows street port or bridge port, previously porting was prohibited.
GT1 Mercedes Benz AMG GT3 in GT1 #31883cars addedneutralMercedes Benz AMG GT3 classified in GT1 at 3050 lbs with 40mm restrictors, prepared per FIA GT3 homologation.
GT1 Wheel Widths #32205tyres & wheelsfasterGT1 wheels: 18-inch tyres get wider rear allowance, from 13 to 14 MAX inches.
STU Single TB Weight Modifiers #31449weightfasterSTU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed.
STU Request to Remove A4 1.8t from STU Spec Line Tables #31465weightslowerSTU Audi A4 1.8T minimum weight fixed at 3050 lbs, VF30 turbo with 35mm restrictor now required only.
STU Improved Touring Tires #32063tyres & wheelsneutralSTL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements.
FA Reorganize Tables 1 and 2 #31985cars addedneutralFA adds Honda K20Z3 2.0L engine spec at 1350 lbs minimum and Mazda MZR 2.0L spec at 1300 lbs minimum to Table 1.
GT1 Wheel Widths #31844tyres & wheelsslowerGT1 allows 17-inch wheels newly; 18-inch wheels require 50 lb penalty; maximum widths 12 front/13 rear, or 13/14 for 18-inch.
STU Request Allowance for Balance Shaft Delete in STU #31434enginefasterSTU engines may delete balance shafts and plug openings; alternate pulleys allowed for timing belt or chain operation only.
STU Request Louvers in hood vents #31916aeroneutralSTU hood vents allowed to include louvers within 200 sq. inch area.
STU Request to Add Honda K23 Spec Line #30682cars addedneutralSTU adds Honda K23 with 2354cc displacement and minimum weight per chart, K24 block allowed with K23 internals and head.
STU RE: Aug FT letter 30682 #31060enginefasterSTU Honda K23 internals rule relaxed to require only K23 crankshaft, allowing other internal modifications.
STU Throttling Device Clarification #31323wordingneutralSTL and STU piston engines clarified: intake manifold and cylinder head porting remains free.
GT1 Request car classification #31032cars addedneutralGT3 Fun Cup Beetle EVO3 classified with 1984 cc sealed SOHC engine, 2060 lbs minimum weight.
FA E&O Table 2 engine names #31085wordingneutralFA Mazda MZR 2.0 spec line removes redundant '2.0' designation; Honda Civic K20Z3 spec line unchanged.
FA Move Toyota 1800 to Table 2 #30822cars addedneutralFA Toyota 1800 moves from Table 1 to Table 2 (Spec Line Cars).
FA E&O Swift 016 wheel width reference #30939wordingneutralFA Swift 016 Mazda MZR/Ford Duratec wheel width specification clarified: front 10, rear 14 minimum and 15 maximum.
GT1 Request to Update GTA Obsolete Part Numbers #30615wordingneutralGTA part numbers updated: 0-80541-1 to 0-80541-2 in two sections and 6010 to 6014X in TA2 Appendix.
FA Update FA rules package #30717wordingneutralFA rule wording clarified: Table 1 for purpose-built and ex-pro cars, Table 2 for spec line cars with exceptions noted.
FA Move Mazda MZR/Ford Duratec 2296cc and 2500cc to Table 2 #30718wordingneutralFA Mazda MZR/Ford Duratec 2296cc and 2500cc moved from Table 1 to Table 2.
FA Clean up Table 2 Mazda MZR 2.0L and Honda Civic K20Z3 spec lines #30719wordingneutralFA Mazda MZR 2.0 and Honda Civic K20Z3 remove sequential designation from 5-speed transmission spec.
STU STU Fender flares #30696wordingneutralSTU fender flare wording clarified: exterior contour of any wheel opening may not change opening size, location or shape from side view.
STU Request weight reduction for 12A bridgeport motor in Miata #30751weight -200 lbsfasterSTU Mazda 12A Bridge Port Miata weight reduced from 2550 lbs to 2350 lbs.
FA E&O Mazda MZR 2.0 and Honda Civic K20Z3 chassis eligibility #30632wordingneutralFA Mazda MZR 2.0 limited to Ralt RT40, RT41, Swift 008, 014 chassis; Honda Civic K20Z3 removes Swift 016 chassis.
FA Correct engine name in Swift 016 2.3 liter spec line #30447wordingneutralFA Swift 016 2.3 liter engine name corrected to Mazda MZR/Ford Duratec.
FA Correct engine name in Swift 016 2.5 liter spec line #30448wordingneutralFA Swift 016 2.5 liter engine name corrected to Mazda MZR/Ford Duratec.
FA Revise Table 1 Spec Lines and clarify application of Engine Notes #30456cars addedunclearFA removes four spec lines and replaces Ford Duratec/Mazda MZR with Honda B16 at 1615cc, 1175 lbs minimum.
STU Request for Fender Flare Clarification #30375wordingneutralSTU fender flare rules clarified: maximum 2 inches, must cover tire contact patch from above, cannot alter body configuration or wheel opening geometry.
FA Update Table 1 Weights for Spec Lines C, I, and K #30355weight -25 lbsfasterFA Spec Line C loses 25 lbs to 1175; Line I loses 75 lbs to 1175; Line K gains 15 lbs to 1175.
FA Remove redundant reference in Table 2 spec line #30366wordingfasterFA purpose built and ex-Pro Atlantic cars lose 25 lb sequential transmission penalty wording.
FA Correct the name of the FR Americas car #30369wordingneutralFA Ligier JS F3 car name corrected in FR Americas spec line.
FA Clean up Spec Line D in Table 1 #30372wordingneutralFA Ford Duratec/Mazda MZR 2500 spec line D wording cleanup: 4-valve becomes 4 valves per cylinder.
FA Table 2 Honda K20Z3 request #30386inductionfasterFA Honda Civic K20Z3 intake manifold and throttle body assembly now allows AT Power Direct-To-Head 45mm individual throttle bodies as alternative to HPD parts.
STU Provision for Interchangeable Engine Components Already Allowed #30342engineunclearSTU Honda S2000 allows F20/F22 K24 crankshaft with chart weight for achieved displacement.
STU ST Oil Coolers E&O Correction to 9.1.4.2.H #30388wordingneutralST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions.
FA E&O FA Intake Restrictors #30273inductionslowerFA Ford Duratec/Mazda MZR intake restrictor reduced from 32mm to 30mm SIR; Swift 016 2.5 Mazda restrictor reduced from 35mm to 33mm SIR.
FA Clean up Spec Lines A and B in Table 1 #30274wordingneutralFA Toyota 4A-GE engines cleaned up, spec lines A and B engine designations corrected.
FA Clean up Spec Line C in Table 1 #30275enginefasterFA Ford BD Series max displacement increases from 1600 to 1615 cc, minimum weight stays 1200 lbs.
FA Clean up Spec Lines J and L in Table 1 #30276wordingneutralFA Ford Duratec/Mazda MZR and Honda B16 both now 1615cc max displacement; Honda B16 removes NA requirement.
FA Move engine specifications to Pro Formula Mazda spec line notes #30278wordingneutralFA Pro Formula Mazda engine specs moved from Table 1 to Table 2 notes; Renesis Rotary details consolidated.
FA Update F3 Americas spec line #30280wordingunclearFA F3 Americas spec line updated effective 2021-03-01; specific changes not legible in provided text.
STU Super Touring Alternate Miata Hubs #30345wordingneutralSTL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs.
STU Brake Component Relocation #29990wordingneutralST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment.
STU Porsche PDK #30081wordingneutralSTU Porsche PDK automatic transmission limited to 8 forward speeds instead of torque converter restriction.
STU Reference Letter #29333 Proposed STU 13B Spec Line Changes #30086inductionfasterSTU Mazda 13B Street Port 2400 removes choke location restriction, allows auto-type 2bbl with dual-Y manifold.
STU Drive Shaft Request #30087wordingneutralSTU driveshaft and half-shaft materials change from OEM-type to steel or aluminum.
FA Request to classify Formula Lites Crawford FL15 #29702cars addedneutralFormula Lites Crawford FL15 newly classified in FA.
STU 13B Rules Adjustment #29333cars addedslowerSTU Mazda 13B Street Port classified at 2400 lbs minimum weight, replacing peripheral and bridge port variants.
STU Request clarification on wing measurement #29640aeroneutralST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch.
GT1 GT Category Wording #29193wordingunclearGT1, GT2, GT3, GTL, GTX now permit turbocharging/supercharging if listed on spec line.
STU Request for Advanced Aero Rule Wording Clarification. #29124wordingneutralSTU fender flare rules reworded: up to 2" per corner allowed with 1% weight penalty total.
GT1 Request to Allow New Trans Am Legal Engines in GT1 #29002engineslowerGT1 adds Trans Am spec engines: Chevrolet R07, Ford FR9, Dodge R7, each with 50 lbs. weight penalty.
STU Minimum Weight Determination #27695wordingneutralSTL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments.
STU ST Gurney flap Wicker clarification #29012wordingneutralSTL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change.
FA Request to Adjust FB Weight for Stock Engines #29005wordingneutralFA stock engines not given weight adjustment; modified engines now allowed in class.
GT1 TA2 Gurney flap wicker clarification #28874wordingneutralTA2 Gurney flap wording clarified: terminology standardized to 'Gurney flap', height limits and thickness specifications remain 0.50 inch / 0.625 inch or 0.375 inch / 0.0625 inch depending on configuration.
GT1 STO Gurney flap wicker clarification #28883wordingneutralSTO rear wing wording clarified: 'wicker' changed to 'Gurney flap' in maximum chord and mounting height rules.
GT1 GT1 Gurney flap wicker clarification #28886wordingneutralGT1 Gurney flap wicker clarification: terminology standardized from lips/tabs/wicker to flaps throughout specifications.
STU Request for Alternate Intake Manifold #26514wordingneutralSTU request for alternate intake manifold denied; no rule change issued.
STU Request for Addition to GT3 Approved Turbo List #27576wordingneutralGT3 and STU add Borg-Warner EFR6258 to approved turbocharger list.
STU Request BoP for my Car #29004wordingneutralSTU large displacement turbo engines limited by GCR turbo list; non-turbo trim suggested as more competitive.
STU Sequential Shifters in STU #29031wordingneutralSTU sequential shifters referred to Board of Directors for approval; no change implemented yet.
FA E&O permitted engine modifications #28831wordingneutralFA engine modifications wording clarified: bore/crankshaft/stroke/flywheel unrestricted if displacement limit met, distributor/transistor ignition allowed without engine modification, compression ratio increasable by machining/gasket chang…
FA E&O Transmissions #28832wordingneutralFA transmission rules clarified: no more than five forward speeds and operational reverse gear unless Table 2 notes otherwise.
FA Swift 016 Gurney flap wicker clarification #28884wordingneutralFA Swift 016 Mazda Duratec Gurney flap wording clarified; terminology and mounting rules unchanged.
STU Rotary Help #27833cars addedneutralSTU Mazda 13B Bridge Port and Street Port engines added with 2550 and 2250 lbs minimum weights respectively.
FA Remove redundant spec line in Table 1 #28720removedneutralFA Volkswagen 1835cc SOHC removed from Table 1.
FA E&O general engine rules #28772wordingneutralFA engine rules clarified: blocks and heads must be OEM unless Tables note exceptions.
FA Request higher compression ratio and prior weights for F1000 cars #28162enginefasterFA Formula 1000 motorcycle-based engine compression ratio raised to 14.5:1 from 13.5:1.
FA Remove redundant wheel dimension provisions #28554wordingneutralFA removes Ex-FSV front wheel width 6–8 inches and rear 8–10 inches provisions; all cars use front 10 inches, rear 14–15 inches.
FA E&O Formula 3 spec line #28596enginefasterFA Formula 3 engines now allowed through 2017, previously 2008, with 30mm restrictor required.
STU Request to approve Honda S2000 HKS supercharger #27281enginefasterSTU Honda S2000 adds HKS Supercharger kits 12001-AH006 and 12001-AH010 as allowed.
STU Request BoP on the Lotus #27637weight +100 lbsslowerSTU Lotus Elise Cup R and SC models, plus Exige SC, gain 100–200 lbs minimum weight.
STU Turbo Inlet Restrictor On MK5 Volkswagen #27704inductionslowerSTU Volkswagen GTI/GLI MK5 and Jetta Mk4 may install turbo inlet restrictor in OEM turbo inlet housing.
STU Honda K20C1 removal #27732inductionslowerSTU Honda K20C1 Turbo I4 restrictor reduces from 36mm to 35mm.
STU Change GM LNF 2.0 Allowance to LSJ Engine for Viable STL 2.0 #27884engineslowerSTU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs.
STU Alternate Engine for Porsche 944 #28259engineunclearSTU Porsche 944 now permits VW/Audi 1.8L and 2.0L turbo engines as alternates.
FA FA weight correction/clarification #28430wordingneutralFA engine note clarification removes Table E reference, Pro Formula Mazda directed to Table 1.
STU Please Modify the STU Wheel Size Rule for Clarity #27694weightfasterSTU vehicles over 2951 lbs base weight may use 9 inch wide wheels, up from 2950 lbs.
STU Turbo Engine Cars Base Weight #28032wordingneutralSTU turbocharged engines now use base weight instead of minimum weight, with 3% DI increase applied to base weight.
GT1 Windshield Clips #27323wordingneutralGT1, GT2, GT3, GTL, GTX may omit windshield clips if factory glass is bonded per original specifications.
FA Request to merge FB into FA #25611cars addedfasterFormula 1000 motorcycle-based engine classified into FA, throttle bodies and ECUs unrestricted.
FA Suggestions for FB/F1000 into FA #27319cars addedunclearF1000 reclassified into FA with specification changes effective 2020-01-01.
FA Change Swift 016 - 2.3 liter Mazda Duratec restrictor size #27880inductionslowerFA Swift 016 2.3L Mazda Duratec restrictor reduced from 33mm to 31mm SIR, making it slower.
GT1 Request to classify the Ford Coyote 3rd Gen OEM #27146cars addedneutralGT2/ST Ford 5.0L Coyote 3rd Gen OEM added at 3200 lbs with Boss intake manifold permitted.
GT1 Request Factory Five Daytona coupe classification #26308cars addedneutralFactory Five Type 65 Coupe R with Ford 302/351 or 5.0/5.2L NA added to GTX-MISC at 2600 lbs.
GT1 Request to Adjust Transmission Penalty #27750weightfasterGT1 sequential shifting transmission weight penalty reduced from 75 to 50 lbs.
GT1 Request to Reduce Additional Weight for 18 #27751weightfasterGT1 non-18-inch-wheel cars now get 18-inch wheels with 50 lb penalty, down from 100 lb.
GT1 Request for Five Star Nascar Compliant Bodywork #27756cars addedneutralGT1 Spec Lines allows 5 Star NASCAR Camaro 2018+ body for General Motors Corporation.
FA Move wheel dimensions from Bodywork subsection to #27493wordingneutralFA wheel dimension rules moved from Bodywork subsection to General section; no specification changes.
FA Table 2 Mazda MZR 2.0 E&O #27640wordingneutralFA Mazda MZR 2.0 now limited to Ralt RT40, Ralt RT41, and Swift 014 chassis only.
STU Request for an electronic throttle body #27342wordingneutralSTU cars with manual OEM throttle bodies may convert to OEM electronic throttle body of same inner diameter.
FA Follow up to Letter #27344 on Honda Powered FA Rules #27363wordingneutralFA Honda Civic K20Z3 engines consolidated: three separate base/uprated specs removed, replaced with single unified 1350 lb minimum weight spec for Swift 014/016.
FA Swift 014 Mazda MZR 2.0 E&O #27305enginefasterFA Swift 014 Mazda MZR 2.0 piston minimum weight reduced from 320g to 280g.
STU Request to correct E&O advanced aerodynamics #27290wordingneutralSTU wing assembly wording corrected: no part higher than roof height.
GT1 Clarify Trans Am Legal Bodywork and Wing #26953aerofasterGT1 allows Trans Am rear wing, 12" chord, 72" span, 1/2" wicker, 100 sq in endplates, no weight penalty.
STU Remove -2mm penalty from SR20DET Nissan #26982enginefasterSTU Nissan SR20DET removes -2mm penalty in Table B.
STU Request clarification for manifold and throttle in STU #27004inductionfasterSTU alternate intake manifolds now allowed case-by-case instead of prohibited.
FA Adjust Line N restrictor size and minimum weight #26691weight +30 lbsslowerFA Line N minimum weight increases to 1375 lbs.
STU Request to clarify afterrmarket side skirts exhaust exit #26814wordingneutralSTU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement.
STU Wheel Flare wording #26872wordingneutralSTU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty.
FA Add data plate requirement #26707wordingneutralFA cars must install AIM part #X47KPFSOLO2R0 data box mount for Majors and Runoffs.
GT1 Request GTX Fuel injection for previous GT-1 tube frame cars #26141inductionfasterGTX tube frame cars gain fuel injection with 90mm maximum throttle body size.
GT1 Request to Classify Ligier JS2 R #26535cars addedneutralLigier JS2 R classified in GTX, no performance parameters specified in filing.
STU Request Ride Height Clarification #26597wordingneutralSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld.
GT1 Request Ride Height Clarification #26600wordingneutralGT1 and GT2/GT3/LITE ride height requirements removed from GCR sections 9.1.2.D.5.a.1 and 9.1.2.F.7.b.
STU Request to Use Japanese Mazda 13b Intake Manifold #25790inductionfasterSTU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock.
STU Request Alternate Intake for Mazda MZR In a Rear Wheel Drive App. #26352inductionunclearSTU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body.
STU E&O Suspension #26424wordingneutralSTU suspension rules clarified: alternate components from same manufacturer moved from section E to section D.
STU Revisit B20 VTEC #26530enginefasterSTU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold.
STU Move Flared Fenders to STU Advanced Aero #26564aeroneutralSTU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules.
STU TCA Civic SI E&O #26606tyres & wheelsslowerTCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019.
STU S54 Spec line #26620wordingneutralSTU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight.
FA Request to add FA engine spec lines #26183weightfasterFA Formula 3 car sequential gearbox weight penalty of 25 lbs removed; minimum weight now 1215 lbs.
STU Request to Class Assignment for 2017 Civic #24287cars addedneutralHonda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork.
STU Request to run E46 3246cc in STU #25126cars addedneutralSTU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances.
STU Engine Classification for Rotary #25564wordingunclearSTU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed.
STU K24/K20 Head Swap Clarification/Amendment #25899wordingneutralSTU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10.
STU Request to Classify 12a Bridge Ported Rotary Engine #25985cars addedneutralSTU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options.
STU World Challenge Car Eligibility #26387wordingunclearSTU World Challenge car weight calculation method removed; new basis unclear from text provided.
STU Request a phone call for discussion regarding weight #26398inductionfasterSTU AWD cars no longer required to reduce restrictor 1 mm from table.
STU Advanced Aero E&O #26413aeroneutralSTU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each.
FA FA MZR 2.0 Engine Specification #25814wordingneutralFA Swift 014-Mazda MZR 2.0 engine now requires OE block casting #LF95 and specific OE components instead of sealed Elite Engines sourcing.
FA FA 016 weight increase #26063weightslowerFA Swift 016 Mazda Duratec 2.3L and 2.5L minimum weight increases from 1420 to 1450 lbs.
GT1 GTX Homologation table update #26034cars addedneutralGTX FIA GT3: Audi R8 40mm restrictor 2900 lbs, BMW Z4 70mm 2800 lbs, Ferrari 488 35mm restrictor 3025 lbs classified.
STU Request to Equalize Direct Injected Turbo Cars #24890cars addedneutralSTU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR.
Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of FA" is the class's best as a share of FA's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when FA's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.